diff options
Diffstat (limited to 'drivers/isdn/hisax/enternow_pci.c')
| -rw-r--r-- | drivers/isdn/hisax/enternow_pci.c | 399 |
1 files changed, 399 insertions, 0 deletions
diff --git a/drivers/isdn/hisax/enternow_pci.c b/drivers/isdn/hisax/enternow_pci.c new file mode 100644 index 00000000000..1cc4d11e007 --- /dev/null +++ b/drivers/isdn/hisax/enternow_pci.c @@ -0,0 +1,399 @@ +/* enternow_pci.c,v 0.99 2001/10/02 + * + * enternow_pci.c Card-specific routines for + * Formula-n enter:now ISDN PCI ab + * Gerdes AG Power ISDN PCI + * Woerltronic SA 16 PCI + * (based on HiSax driver by Karsten Keil) + * + * Author Christoph Ersfeld <info@formula-n.de> + * Formula-n Europe AG (www.formula-n.com) + * previously Gerdes AG + * + * + * This file is (c) under GNU PUBLIC LICENSE + * + * Notes: + * This driver interfaces to netjet.c which performs B-channel + * processing. + * + * Version 0.99 is the first release of this driver and there are + * certainly a few bugs. + * It isn't testet on linux 2.4 yet, so consider this code to be + * beta. + * + * Please don't report me any malfunction without sending + * (compressed) debug-logs. + * It would be nearly impossible to retrace it. + * + * Log D-channel-processing as follows: + * + * 1. Load hisax with card-specific parameters, this example ist for + * Formula-n enter:now ISDN PCI and compatible + * (f.e. Gerdes Power ISDN PCI) + * + * modprobe hisax type=41 protocol=2 id=gerdes + * + * if you chose an other value for id, you need to modify the + * code below, too. + * + * 2. set debug-level + * + * hisaxctrl gerdes 1 0x3ff + * hisaxctrl gerdes 11 0x4f + * cat /dev/isdnctrl >> ~/log & + * + * Please take also a look into /var/log/messages if there is + * anything importand concerning HISAX. + * + * + * Credits: + * Programming the driver for Formula-n enter:now ISDN PCI and + * necessary the driver for the used Amd 7930 D-channel-controller + * was spnsored by Formula-n Europe AG. + * Thanks to Karsten Keil and Petr Novak, who gave me support in + * Hisax-specific questions. + * I want so say special thanks to Carl-Friedrich Braun, who had to + * answer a lot of questions about generally ISDN and about handling + * of the Amd-Chip. + * + */ + + +#include <linux/config.h> +#include "hisax.h" +#include "isac.h" +#include "isdnl1.h" +#include "amd7930_fn.h" +#include "enternow.h" +#include <linux/interrupt.h> +#include <linux/ppp_defs.h> +#include <linux/pci.h> +#include <linux/init.h> +#include "netjet.h" + + + +const char *enternow_pci_rev = "$Revision: 1.1.4.5 $"; + + +/* *************************** I/O-Interface functions ************************************* */ + + +/* cs->readisac, macro rByteAMD */ +BYTE +ReadByteAmd7930(struct IsdnCardState *cs, BYTE offset) +{ + /* direktes Register */ + if(offset < 8) + return (InByte(cs->hw.njet.isac + 4*offset)); + + /* indirektes Register */ + else { + OutByte(cs->hw.njet.isac + 4*AMD_CR, offset); + return(InByte(cs->hw.njet.isac + 4*AMD_DR)); + } +} + +/* cs->writeisac, macro wByteAMD */ +void +WriteByteAmd7930(struct IsdnCardState *cs, BYTE offset, BYTE value) +{ + /* direktes Register */ + if(offset < 8) + OutByte(cs->hw.njet.isac + 4*offset, value); + + /* indirektes Register */ + else { + OutByte(cs->hw.njet.isac + 4*AMD_CR, offset); + OutByte(cs->hw.njet.isac + 4*AMD_DR, value); + } +} + + +void +enpci_setIrqMask(struct IsdnCardState *cs, BYTE val) { + if (!val) + OutByte(cs->hw.njet.base+NETJET_IRQMASK1, 0x00); + else + OutByte(cs->hw.njet.base+NETJET_IRQMASK1, TJ_AMD_IRQ); +} + + +static BYTE dummyrr(struct IsdnCardState *cs, int chan, BYTE off) +{ + return(5); +} + +static void dummywr(struct IsdnCardState *cs, int chan, BYTE off, BYTE value) +{ + +} + + +/* ******************************************************************************** */ + + +static void +reset_enpci(struct IsdnCardState *cs) +{ + if (cs->debug & L1_DEB_ISAC) + debugl1(cs, "enter:now PCI: reset"); + + /* Reset on, (also for AMD) */ + cs->hw.njet.ctrl_reg = 0x07; + OutByte(cs->hw.njet.base + NETJET_CTRL, cs->hw.njet.ctrl_reg); + mdelay(20); + /* Reset off */ + cs->hw.njet.ctrl_reg = 0x30; + OutByte(cs->hw.njet.base + NETJET_CTRL, cs->hw.njet.ctrl_reg); + /* 20ms delay */ + mdelay(20); + cs->hw.njet.auxd = 0; // LED-status + cs->hw.njet.dmactrl = 0; + OutByte(cs->hw.njet.base + NETJET_AUXCTRL, ~TJ_AMD_IRQ); + OutByte(cs->hw.njet.base + NETJET_IRQMASK1, TJ_AMD_IRQ); + OutByte(cs->hw.njet.auxa, cs->hw.njet.auxd); // LED off +} + + +static int +enpci_card_msg(struct IsdnCardState *cs, int mt, void *arg) +{ + u_long flags; + BYTE *chan; + + if (cs->debug & L1_DEB_ISAC) + debugl1(cs, "enter:now PCI: card_msg: 0x%04X", mt); + + switch (mt) { + case CARD_RESET: + spin_lock_irqsave(&cs->lock, flags); + reset_enpci(cs); + Amd7930_init(cs); + spin_unlock_irqrestore(&cs->lock, flags); + break; + case CARD_RELEASE: + release_io_netjet(cs); + break; + case CARD_INIT: + reset_enpci(cs); + inittiger(cs); + /* irq must be on here */ + Amd7930_init(cs); + break; + case CARD_TEST: + break; + case MDL_ASSIGN: + /* TEI assigned, LED1 on */ + cs->hw.njet.auxd = TJ_AMD_IRQ << 1; + OutByte(cs->hw.njet.base + NETJET_AUXDATA, cs->hw.njet.auxd); + break; + case MDL_REMOVE: + /* TEI removed, LEDs off */ + cs->hw.njet.auxd = 0; + OutByte(cs->hw.njet.base + NETJET_AUXDATA, 0x00); + break; + case MDL_BC_ASSIGN: + /* activate B-channel */ + chan = (BYTE *)arg; + + if (cs->debug & L1_DEB_ISAC) + debugl1(cs, "enter:now PCI: assign phys. BC %d in AMD LMR1", *chan); + + cs->dc.amd7930.ph_command(cs, (cs->dc.amd7930.lmr1 | (*chan + 1)), "MDL_BC_ASSIGN"); + /* at least one b-channel in use, LED 2 on */ + cs->hw.njet.auxd |= TJ_AMD_IRQ << 2; + OutByte(cs->hw.njet.base + NETJET_AUXDATA, cs->hw.njet.auxd); + break; + case MDL_BC_RELEASE: + /* deactivate B-channel */ + chan = (BYTE *)arg; + + if (cs->debug & L1_DEB_ISAC) + debugl1(cs, "enter:now PCI: release phys. BC %d in Amd LMR1", *chan); + + cs->dc.amd7930.ph_command(cs, (cs->dc.amd7930.lmr1 & ~(*chan + 1)), "MDL_BC_RELEASE"); + /* no b-channel active -> LED2 off */ + if (!(cs->dc.amd7930.lmr1 & 3)) { + cs->hw.njet.auxd &= ~(TJ_AMD_IRQ << 2); + OutByte(cs->hw.njet.base + NETJET_AUXDATA, cs->hw.njet.auxd); + } + break; + default: + break; + + } + return(0); +} + +static irqreturn_t +enpci_interrupt(int intno, void *dev_id, struct pt_regs *regs) +{ + struct IsdnCardState *cs = dev_id; + BYTE s0val, s1val, ir; + u_long flags; + + spin_lock_irqsave(&cs->lock, flags); + s1val = InByte(cs->hw.njet.base + NETJET_IRQSTAT1); + + /* AMD threw an interrupt */ + if (!(s1val & TJ_AMD_IRQ)) { + /* read and clear interrupt-register */ + ir = ReadByteAmd7930(cs, 0x00); + Amd7930_interrupt(cs, ir); + s1val = 1; + } else + s1val = 0; + s0val = InByte(cs->hw.njet.base + NETJET_IRQSTAT0); + if ((s0val | s1val)==0) { // shared IRQ + spin_unlock_irqrestore(&cs->lock, flags); + return IRQ_NONE; + } + if (s0val) + OutByte(cs->hw.njet.base + NETJET_IRQSTAT0, s0val); + + /* DMA-Interrupt: B-channel-stuff */ + /* set bits in sval to indicate which page is free */ + if (inl(cs->hw.njet.base + NETJET_DMA_WRITE_ADR) < + inl(cs->hw.njet.base + NETJET_DMA_WRITE_IRQ)) + /* the 2nd write page is free */ + s0val = 0x08; + else /* the 1st write page is free */ + s0val = 0x04; + if (inl(cs->hw.njet.base + NETJET_DMA_READ_ADR) < + inl(cs->hw.njet.base + NETJET_DMA_READ_IRQ)) + /* the 2nd read page is free */ + s0val = s0val | 0x02; + else /* the 1st read page is free */ + s0val = s0val | 0x01; + if (s0val != cs->hw.njet.last_is0) /* we have a DMA interrupt */ + { + if (test_and_set_bit(FLG_LOCK_ATOMIC, &cs->HW_Flags)) { + spin_unlock_irqrestore(&cs->lock, flags); + return IRQ_HANDLED; + } + cs->hw.njet.irqstat0 = s0val; + if ((cs->hw.njet.irqstat0 & NETJET_IRQM0_READ) != + (cs->hw.njet.last_is0 & NETJET_IRQM0_READ)) + /* we have a read dma int */ + read_tiger(cs); + if ((cs->hw.njet.irqstat0 & NETJET_IRQM0_WRITE) != + (cs->hw.njet.last_is0 & NETJET_IRQM0_WRITE)) + /* we have a write dma int */ + write_tiger(cs); + test_and_clear_bit(FLG_LOCK_ATOMIC, &cs->HW_Flags); + } + spin_unlock_irqrestore(&cs->lock, flags); + return IRQ_HANDLED; +} + + +static struct pci_dev *dev_netjet __initdata = NULL; + +/* called by config.c */ +int __init +setup_enternow_pci(struct IsdnCard *card) +{ + int bytecnt; + struct IsdnCardState *cs = card->cs; + char tmp[64]; + +#ifdef CONFIG_PCI +#ifdef __BIG_ENDIAN +#error "not running on big endian machines now" +#endif + strcpy(tmp, enternow_pci_rev); + printk(KERN_INFO "HiSax: Formula-n Europe AG enter:now ISDN PCI driver Rev. %s\n", HiSax_getrev(tmp)); + if (cs->typ != ISDN_CTYPE_ENTERNOW) + return(0); + test_and_clear_bit(FLG_LOCK_ATOMIC, &cs->HW_Flags); + + for ( ;; ) + { + if ((dev_netjet = pci_find_device(PCI_VENDOR_ID_TIGERJET, + PCI_DEVICE_ID_TIGERJET_300, dev_netjet))) { + if (pci_enable_device(dev_netjet)) + return(0); + cs->irq = dev_netjet->irq; + if (!cs->irq) { + printk(KERN_WARNING "enter:now PCI: No IRQ for PCI card found\n"); + return(0); + } + cs->hw.njet.base = pci_resource_start(dev_netjet, 0); + if (!cs->hw.njet.base) { + printk(KERN_WARNING "enter:now PCI: No IO-Adr for PCI card found\n"); + return(0); + } + /* checks Sub-Vendor ID because system crashes with Traverse-Card */ + if ((dev_netjet->subsystem_vendor != 0x55) || + (dev_netjet->subsystem_device != 0x02)) { + printk(KERN_WARNING "enter:now: You tried to load this driver with an incompatible TigerJet-card\n"); + printk(KERN_WARNING "Use type=20 for Traverse NetJet PCI Card.\n"); + return(0); + } + } else { + printk(KERN_WARNING "enter:now PCI: No PCI card found\n"); + return(0); + } + + cs->hw.njet.auxa = cs->hw.njet.base + NETJET_AUXDATA; + cs->hw.njet.isac = cs->hw.njet.base + 0xC0; // Fenster zum AMD + + /* Reset an */ + cs->hw.njet.ctrl_reg = 0x07; // geändert von 0xff + OutByte(cs->hw.njet.base + NETJET_CTRL, cs->hw.njet.ctrl_reg); + /* 20 ms Pause */ + mdelay(20); + + cs->hw.njet.ctrl_reg = 0x30; /* Reset Off and status read clear */ + OutByte(cs->hw.njet.base + NETJET_CTRL, cs->hw.njet.ctrl_reg); + mdelay(10); + + cs->hw.njet.auxd = 0x00; // war 0xc0 + cs->hw.njet.dmactrl = 0; + + OutByte(cs->hw.njet.base + NETJET_AUXCTRL, ~TJ_AMD_IRQ); + OutByte(cs->hw.njet.base + NETJET_IRQMASK1, TJ_AMD_IRQ); + OutByte(cs->hw.njet.auxa, cs->hw.njet.auxd); + + break; + } +#else + + printk(KERN_WARNING "enter:now PCI: NO_PCI_BIOS\n"); + printk(KERN_WARNING "enter:now PCI: unable to config Formula-n enter:now ISDN PCI ab\n"); + return (0); + +#endif /* CONFIG_PCI */ + + bytecnt = 256; + + printk(KERN_INFO + "enter:now PCI: PCI card configured at 0x%lx IRQ %d\n", + cs->hw.njet.base, cs->irq); + if (!request_region(cs->hw.njet.base, bytecnt, "Fn_ISDN")) { + printk(KERN_WARNING + "HiSax: %s config port %lx-%lx already in use\n", + CardType[card->typ], + cs->hw.njet.base, + cs->hw.njet.base + bytecnt); + return (0); + } + setup_Amd7930(cs); + cs->hw.njet.last_is0 = 0; + /* macro rByteAMD */ + cs->readisac = &ReadByteAmd7930; + /* macro wByteAMD */ + cs->writeisac = &WriteByteAmd7930; + cs->dc.amd7930.setIrqMask = &enpci_setIrqMask; + + cs->BC_Read_Reg = &dummyrr; + cs->BC_Write_Reg = &dummywr; + cs->BC_Send_Data = &netjet_fill_dma; + cs->cardmsg = &enpci_card_msg; + cs->irq_func = &enpci_interrupt; + cs->irq_flags |= SA_SHIRQ; + + return (1); +} |