diff options
Diffstat (limited to 'drivers/tty/serial/sh-sci.c')
-rw-r--r-- | drivers/tty/serial/sh-sci.c | 183 |
1 files changed, 165 insertions, 18 deletions
diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c index aff9d612dff..9e62349b3d9 100644 --- a/drivers/tty/serial/sh-sci.c +++ b/drivers/tty/serial/sh-sci.c @@ -50,6 +50,7 @@ #include <linux/dma-mapping.h> #include <linux/scatterlist.h> #include <linux/slab.h> +#include <linux/gpio.h> #ifdef CONFIG_SUPERH #include <asm/sh_bios.h> @@ -73,6 +74,7 @@ struct sci_port { struct clk *fclk; char *irqstr[SCIx_NR_IRQS]; + char *gpiostr[SCIx_NR_FNS]; struct dma_chan *chan_tx; struct dma_chan *chan_rx; @@ -474,8 +476,15 @@ static void sci_init_pins(struct uart_port *port, unsigned int cflag) if (!reg->size) return; - if (!(cflag & CRTSCTS)) - sci_out(port, SCSPTR, 0x0080); /* Set RTS = 1 */ + if ((s->cfg->capabilities & SCIx_HAVE_RTSCTS) && + ((!(cflag & CRTSCTS)))) { + unsigned short status; + + status = sci_in(port, SCSPTR); + status &= ~SCSPTR_CTSIO; + status |= SCSPTR_RTSIO; + sci_out(port, SCSPTR, status); /* Set RTS = 1 */ + } } static int sci_txfill(struct uart_port *port) @@ -621,6 +630,7 @@ static void sci_receive_chars(struct uart_port *port) } else { for (i = 0; i < count; i++) { char c = sci_in(port, SCxRDR); + status = sci_in(port, SCxSR); #if defined(CONFIG_CPU_SH3) /* Skip "chars" during break */ @@ -649,9 +659,11 @@ static void sci_receive_chars(struct uart_port *port) /* Store data and status */ if (status & SCxSR_FER(port)) { flag = TTY_FRAME; + port->icount.frame++; dev_notice(port->dev, "frame error\n"); } else if (status & SCxSR_PER(port)) { flag = TTY_PARITY; + port->icount.parity++; dev_notice(port->dev, "parity error\n"); } else flag = TTY_NORMAL; @@ -723,6 +735,8 @@ static int sci_handle_errors(struct uart_port *port) */ if (s->cfg->overrun_bit != SCIx_NOT_SUPPORTED) { if (status & (1 << s->cfg->overrun_bit)) { + port->icount.overrun++; + /* overrun error */ if (tty_insert_flip_char(tty, 0, TTY_OVERRUN)) copied++; @@ -737,6 +751,8 @@ static int sci_handle_errors(struct uart_port *port) struct sci_port *sci_port = to_sci_port(port); if (!sci_port->break_flag) { + port->icount.brk++; + sci_port->break_flag = 1; sci_schedule_break_timer(sci_port); @@ -752,6 +768,8 @@ static int sci_handle_errors(struct uart_port *port) } else { /* frame error */ + port->icount.frame++; + if (tty_insert_flip_char(tty, 0, TTY_FRAME)) copied++; @@ -761,6 +779,8 @@ static int sci_handle_errors(struct uart_port *port) if (status & SCxSR_PER(port)) { /* parity error */ + port->icount.parity++; + if (tty_insert_flip_char(tty, 0, TTY_PARITY)) copied++; @@ -787,6 +807,8 @@ static int sci_handle_fifo_overrun(struct uart_port *port) if ((sci_in(port, SCLSR) & (1 << s->cfg->overrun_bit))) { sci_out(port, SCLSR, 0); + port->icount.overrun++; + tty_insert_flip_char(tty, 0, TTY_OVERRUN); tty_flip_buffer_push(tty); @@ -812,6 +834,9 @@ static int sci_handle_breaks(struct uart_port *port) /* Debounce break */ s->break_flag = 1; #endif + + port->icount.brk++; + /* Notify of BREAK */ if (tty_insert_flip_char(tty, 0, TTY_BREAK)) copied++; @@ -1082,6 +1107,67 @@ static void sci_free_irq(struct sci_port *port) } } +static const char *sci_gpio_names[SCIx_NR_FNS] = { + "sck", "rxd", "txd", "cts", "rts", +}; + +static const char *sci_gpio_str(unsigned int index) +{ + return sci_gpio_names[index]; +} + +static void __devinit sci_init_gpios(struct sci_port *port) +{ + struct uart_port *up = &port->port; + int i; + + if (!port->cfg) + return; + + for (i = 0; i < SCIx_NR_FNS; i++) { + const char *desc; + int ret; + + if (!port->cfg->gpios[i]) + continue; + + desc = sci_gpio_str(i); + + port->gpiostr[i] = kasprintf(GFP_KERNEL, "%s:%s", + dev_name(up->dev), desc); + + /* + * If we've failed the allocation, we can still continue + * on with a NULL string. + */ + if (!port->gpiostr[i]) + dev_notice(up->dev, "%s string allocation failure\n", + desc); + + ret = gpio_request(port->cfg->gpios[i], port->gpiostr[i]); + if (unlikely(ret != 0)) { + dev_notice(up->dev, "failed %s gpio request\n", desc); + + /* + * If we can't get the GPIO for whatever reason, + * no point in keeping the verbose string around. + */ + kfree(port->gpiostr[i]); + } + } +} + +static void sci_free_gpios(struct sci_port *port) +{ + int i; + + for (i = 0; i < SCIx_NR_FNS; i++) + if (port->cfg->gpios[i]) { + gpio_free(port->cfg->gpios[i]); + kfree(port->gpiostr[i]); + } +} + static unsigned int sci_tx_empty(struct uart_port *port) { unsigned short status = sci_in(port, SCxSR); @@ -1090,19 +1176,39 @@ static unsigned int sci_tx_empty(struct uart_port *port) return (status & SCxSR_TEND(port)) && !in_tx_fifo ? TIOCSER_TEMT : 0; } +/* + * Modem control is a bit of a mixed bag for SCI(F) ports. Generally + * CTS/RTS is supported in hardware by at least one port and controlled + * via SCSPTR (SCxPCR for SCIFA/B parts), or external pins (presently + * handled via the ->init_pins() op, which is a bit of a one-way street, + * lacking any ability to defer pin control -- this will later be + * converted over to the GPIO framework). + * + * Other modes (such as loopback) are supported generically on certain + * port types, but not others. For these it's sufficient to test for the + * existence of the support register and simply ignore the port type. + */ static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl) { - /* This routine is used for seting signals of: DTR, DCD, CTS/RTS */ - /* We use SCIF's hardware for CTS/RTS, so don't need any for that. */ - /* If you have signals for DTR and DCD, please implement here. */ + if (mctrl & TIOCM_LOOP) { + struct plat_sci_reg *reg; + + /* + * Standard loopback mode for SCFCR ports. + */ + reg = sci_getreg(port, SCFCR); + if (reg->size) + sci_out(port, SCFCR, sci_in(port, SCFCR) | 1); + } } static unsigned int sci_get_mctrl(struct uart_port *port) { - /* This routine is used for getting signals of: DTR, DCD, DSR, RI, - and CTS/RTS */ - - return TIOCM_DTR | TIOCM_RTS | TIOCM_CTS | TIOCM_DSR; + /* + * CTS/RTS is handled in hardware when supported, while nothing + * else is wired up. Keep it simple and simply assert DSR/CAR. + */ + return TIOCM_DSR | TIOCM_CAR; } #ifdef CONFIG_SERIAL_SH_SCI_DMA @@ -1449,12 +1555,17 @@ static void sci_stop_rx(struct uart_port *port) static void sci_enable_ms(struct uart_port *port) { - /* Nothing here yet .. */ + /* + * Not supported by hardware, always a nop. + */ } static void sci_break_ctl(struct uart_port *port, int break_state) { - /* Nothing here yet .. */ + /* + * Not supported by hardware. Most parts couple break and rx + * interrupts together, with break detection always enabled. + */ } #ifdef CONFIG_SERIAL_SH_SCI_DMA @@ -1652,6 +1763,7 @@ static unsigned int sci_scbrr_calc(unsigned int algo_id, unsigned int bps, static void sci_reset(struct uart_port *port) { + struct plat_sci_reg *reg; unsigned int status; do { @@ -1660,7 +1772,8 @@ static void sci_reset(struct uart_port *port) sci_out(port, SCSCR, 0x00); /* TE=0, RE=0, CKE1=0 */ - if (port->type != PORT_SCI) + reg = sci_getreg(port, SCFCR); + if (reg->size) sci_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST); } @@ -1668,9 +1781,9 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old) { struct sci_port *s = to_sci_port(port); + struct plat_sci_reg *reg; unsigned int baud, smr_val, max_baud; int t = -1; - u16 scfcr = 0; /* * earlyprintk comes here early on with port->uartclk set to zero. @@ -1720,7 +1833,27 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios, } sci_init_pins(port, termios->c_cflag); - sci_out(port, SCFCR, scfcr | ((termios->c_cflag & CRTSCTS) ? SCFCR_MCE : 0)); + + reg = sci_getreg(port, SCFCR); + if (reg->size) { + unsigned short ctrl = sci_in(port, SCFCR); + + if (s->cfg->capabilities & SCIx_HAVE_RTSCTS) { + if (termios->c_cflag & CRTSCTS) + ctrl |= SCFCR_MCE; + else + ctrl &= ~SCFCR_MCE; + } + + /* + * As we've done a sci_reset() above, ensure we don't + * interfere with the FIFOs while toggling MCE. As the + * reset values could still be set, simply mask them out. + */ + ctrl &= ~(SCFCR_RFRST | SCFCR_TFRST); + + sci_out(port, SCFCR, ctrl); + } sci_out(port, SCSCR, s->cfg->scscr); @@ -1892,6 +2025,8 @@ static int __devinit sci_init_single(struct platform_device *dev, struct uart_port *port = &sci_port->port; int ret; + sci_port->cfg = p; + port->ops = &sci_uart_ops; port->iotype = UPIO_MEM; port->line = index; @@ -1937,6 +2072,8 @@ static int __devinit sci_init_single(struct platform_device *dev, port->dev = &dev->dev; + sci_init_gpios(sci_port); + pm_runtime_irq_safe(&dev->dev); pm_runtime_enable(&dev->dev); } @@ -1971,8 +2108,6 @@ static int __devinit sci_init_single(struct platform_device *dev, p->error_mask |= (1 << p->overrun_bit); } - sci_port->cfg = p; - port->mapbase = p->mapbase; port->type = p->type; port->flags = p->flags; @@ -2113,9 +2248,16 @@ static int sci_runtime_suspend(struct device *dev) struct uart_port *port = &sci_port->port; if (uart_console(port)) { + struct plat_sci_reg *reg; + sci_port->saved_smr = sci_in(port, SCSMR); sci_port->saved_brr = sci_in(port, SCBRR); - sci_port->saved_fcr = sci_in(port, SCFCR); + + reg = sci_getreg(port, SCFCR); + if (reg->size) + sci_port->saved_fcr = sci_in(port, SCFCR); + else + sci_port->saved_fcr = 0; } return 0; } @@ -2129,7 +2271,10 @@ static int sci_runtime_resume(struct device *dev) sci_reset(port); sci_out(port, SCSMR, sci_port->saved_smr); sci_out(port, SCBRR, sci_port->saved_brr); - sci_out(port, SCFCR, sci_port->saved_fcr); + + if (sci_port->saved_fcr) + sci_out(port, SCFCR, sci_port->saved_fcr); + sci_out(port, SCSCR, sci_port->cfg->scscr); } return 0; @@ -2169,6 +2314,8 @@ static int sci_remove(struct platform_device *dev) cpufreq_unregister_notifier(&port->freq_transition, CPUFREQ_TRANSITION_NOTIFIER); + sci_free_gpios(port); + uart_remove_one_port(&sci_uart_driver, &port->port); clk_put(port->iclk); |