| Age | Commit message (Collapse) | Author |
|---|
|
The version 3 and version 4 ColdFire cache controllers support both
write-through and copy-back modes on the data cache. Allow for Kconfig
time configuration of this, and set the cache mode appropriately.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The newer version 2 ColdFire CPU cores support a configurable cache
arrangement. The cache memory can be used as all instruction cache, all
data cache, or split in half for both instruction and data caching.
Support this setup via a Kconfig time menu that allows a kernel builder
to choose the arrangement they want to use.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Currently the code to push cache lines is only available to version 4
cores. Version 3 cores may also need to use this if we support copy-
back caches on them. Move this code to make it more generic, and
useful for all version ColdFire cores.
With this in place we can now have a single cache_flush_all() code
path that does all the right things on all version cores.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The cache control code for the ColdFire CPU's is a big ugly mess
of "#ifdef"ery liberally coated with bit constants. Clean it up.
The cache controllers in the various ColdFire parts are actually quite
similar. Just differing in some bit flags and options supported. Using
the header defines now in place it is pretty easy to factor out the
small differences and use common setup and flush/invalidate code.
I have preserved the cache setups as they where in the old code
(except where obviously wrong - like in the case of the 5249). Following
from this it should be easy now to extend the possible setups used on
the CACHE controllers that support split cacheing or copy-back or
write through options.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The empty __iounmap() function is not used on m68knommu at all.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The kernel_map() functions is not used anywhere, remove it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The non-MMU m68k does not use the do_page_fault() code, so remove it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The more modern ColdFire parts (even if based on older version cores)
have separate user and supervisor stack pointers (a7 register).
Modify the ColdFire CPU setup and exception code to enable and use
this on parts that have it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
There is no need for the DEBUG based command line printing in here.
The kernel will print out the command line in the banner later in
the boot up. So remove it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
There are no users of the old "fasthandler" interrupt entry code.
So remove it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The instruction timings of the ColdFire 54xx family parts are
different to other version 4 parts (or version 2 or 3 parts for
that matter too).
Move the instruction timing setting into the ColdFire part
specific headers, and set the 54xx value appropriately.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Move the ColdFire CPU names out of setup.c and into their repsective
headers. That way when we add new ones we won't need to modify
setup.c any more.
Add the missing 548x CPU name.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The Freescale M547x family of ColdFire processors is very similar
to the M548x series. We use all the same support for it. Initially
all we need is a high level configuration option for it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The ColdFire 547x family of processors is very similar to the ColdFire
548x series. Almost all of the support for them is the same. Make the
code supporting the 548x more gneric, so it will be capable of
supporting both families.
For the most part this is a renaming excerise to make the support
code more obviously apply to both families.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (38 commits)
kbuild: convert `arch/tile' to the kconfig mainmenu upgrade
README: cite nconfig
Revert "kconfig: Temporarily disable dependency warnings"
kconfig: Use PATH_MAX instead of 128 for path buffer sizes.
kconfig: Fix realloc usage()
kconfig: Propagate const
kconfig: Don't go out from read config loop when you read new symbol
kconfig: fix menuconfig on debian lenny
kbuild: migrate all arch to the kconfig mainmenu upgrade
kconfig: expand file names
kconfig: use the file's name of sourced file
kconfig: constify file name
kconfig: don't emit warning upon rootmenu's prompt redefinition
kconfig: replace KERNELVERSION usage by the mainmenu's prompt
kconfig: delay gconf window initialization
kconfig: expand by default the rootmenu's prompt
kconfig: add a symbol string expansion helper
kconfig: regen parser
kconfig: implement the `mainmenu' directive
kconfig: allow PACKAGE to be defined on the compiler's command-line
...
Fix up trivial conflict in arch/mn10300/Kconfig
|
|
Use new 'regno', 'datap' variables in order to remove duplicated
expressions and unnecessary castings. Alse remove checking @addr less
than 0 because addr is now unsigned.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix up the arguments to arch_ptrace() to take account of the fact that
@addr and @data are now unsigned long rather than long as of a preceding
patch in this series.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (21 commits)
m68knommu: convert to using tracehook_report_syscall_*
m68knommu: some boards use fixed phy for FEC ethernet
m68knommu: support the external GPIO based interrupts of the 5272
m68knommu: mask of vector bits in exception word properly
m68knommu: change to new flag variables
m68knommu: Fix MCFUART_TXFIFOSIZE for m548x.
m68knommu: add basic mmu-less m548x support
m68knommu: .gitignore vmlinux.lds
m68knommu: stop using __do_IRQ
m68knommu: rename PT_OFF_VECTOR to PT_OFF_FORMATVEC.
m68knommu: add support for Coldfire 547x/548x interrupt controller
m68k{nommu}: Remove unused DEFINE's from asm-offsets.c
m68knommu: whitespace cleanup in 68328/entry.S
m68knommu: Document supported chips in intc-2.c and intc-simr.c.
m68knommu: fix strace support for 68328/68360
m68knommu: fix default starting date
arch/m68knommu: Removing dead 68328_SERIAL_UART2 config option
arch/m68knommu: Removing dead RAM_{16,32}_MB config option
arch/m68knommu: Removing dead M68KFPU_EMU config option
arch/m68knommu: Removing dead RELOCATE config option
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Add missing I/O macros {in,out}{w,l}_p() for !CONFIG_ISA
m68k: Remove big kernel lock in cache flush code
m68k: __pa(): cast arg to long
fbdev: atafb - Remove undead ifdef ATAFB_FALCON
zorro: Fix device_register() error handling
fbdev/m68k: Fix section mismatches in q40fb.c
m68k/m68knommu: merge the MMU and non-MMU traps.h
m68k/m68knommu: merge MMU and non-MMU thread_info.h
m68k/m68knommu: merge MMU and non-MMU atomic.h
m68k/m68knommu: clean up page.h
m68k/m68knommu: merge machdep.h files into a single file
m68k/m68knommu: merge MMU and non-MMU string.h
m68k/m68knommu: Remove dead SMP config option
m68k: move definition of THREAD_SIZE into thread_info_mm.h
m68k: Use asm-generic/ioctls.h (enables termiox)
m68k: Remove dead GG2 config option
|
|
The MMU and non-MMU versions of thread_info.h are quite similar.
Merge the two files.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
CONFIG_SMP doesn't exist in Kconfig (for this architecure), therefore
remove all references to it from the source.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Break up syscall_trace() into separate entry and exit routines that use
tracehook_report_syscall_entry() and tracehook_report_syscall_exit().
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Define a fixed phy setup for use on boarts that directly connect the
FEC ethernet controller to a switch.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The external GPIO interrupts of the ColdFire 5272 SoC are edge triggered,
unlike the internal interrupt sources (which are level triggered).
Add proper support for these interrupts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The vector field of the processors exception frame actually contains
both the vector exception number and fault status field bits.
The exception processing code was not correctly masking out the
fault status field bits before switching on the vector number.
The default case was catching the bad check, but we are reporting
the wrong kind of exception in some cases.
Reported-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Replace EXTRA_CFLAGS with ccflags-y and EXTRA_AFLAGS with asflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Add a very basic mmu-less support for coldfire m548x family. This is perhaps
also valid for m547x family. The port comprises the serial, tick timer and
reboot support. The gpio part compiles but is empty. This gives a functional
albeit limited linux for the m548x coldfire family. This has been tested
on a Freescale M548xEVB Lite board with a M5484 processor and the default
dbug monitor.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The use of __do_IRQ is deprecated, so lets stop using it.
Generally the interrupts on the supported processors here are
level triggered, so this is strait forward to switch over to
using the standard handle_level_irq flow handler. (Although
some ColdFire parts support edge triggered GPIO line interrupts
we have no support for them yet).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
In m68k/m68knommu assembly files, the same value is called sometimes
PT_OFF_VECTOR, but more frequently PT_OFF_FORMATVEC. Standardize
name to PT_OFF_FORMATVEC.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The Coldfire MCF547x/MCF548x have the same interrupt controller as
the MCF528x e.g., but only one, not two as in the MCF528x. Modify
intc-2.c to support only one interrupt controller if MCFICM_INTC1 is
not defined.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
m68k{nommu}/asm-offsets.c define many constants which are not used
anymore anywhere; remove IRQ_DEVID, IRQ_HANDLER, IRQ_NEXT, STAT_IRQ,
TASK_ACTIVE_MM, TASK_BLOCKED, TASK_FLAGS, TASK_PTRACE, TASK_STATE,
TASK_THREAD_INFO, TI_CPU, TI_EXECDOMAIN and TI_TASK.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The chips lists were in commit logs, but should also be in source files.
This way it is easier to choose the right source file for a not yet
supported Coldfire.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
strace enabled is marked using the `flags' field of the `thread_info' struct.
68360 version of entry.S did test a wrong bit in a wrong structure
(task_struct).
68328 version of entry.S did test the right bit in the right structure,
but wrongly, because the `flags' field is 32 bit wide, while the used
assembler insn (btst) only accesses a 8 bit byte in memory.
Fix both using code already used in the coldfire version of entry.S
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Currently m68knommu boards without RTC chip start with an unexpected
default date of 1999-11-30 (Actually the source asks for 2000-00-00)
Make that 1970-01-01 instead, as expected.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
CONFIG_68328_SERIAL_UART2 doesn't exist in Kconfig, therefore removing
all references to it from the source.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
CONFIG_RAM_{16,32}_MB doesn't exist in Kconfig, therefore removing
all references to it from the source.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
CONFIG_M68KFPU_EMU doesn't exist in Kconfig, therefore removing
all references to it from the source. This Flags seems to exist only
on m68k with mmu, and this dead blocks are copy paste.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
CONFIG_RELOCATE doesn't exist in Kconfig, therefore removing
all references to it from the source.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
CONFIG_M68000 doesn't exist in Kconfig, therefore removing
all references to it from the source.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
We need to revert the temporary hack in 71ebc01, hence the merge.
|
|
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
|
|
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Michal Marek <mmarek@suse.cz>
|
|
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
|
|
Recent changes to linker segments that hold per-cpu data broke linking
for m68knommu targets:
LD vmlinux
/usr/local/bin/m68k-uclinux-ld.real: error: no memory region specified for loadable section `.data..shared_aligned'
Add missing segments into the m68knommu linker script.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: include sched.h in ColdFire/SPI driver
m68knommu: formatting of pointers in printk()
m68knommu: arch/m68k/include/asm/ide.h fix for nommu
|
|
arch/m68knommu/kernel/process.c: formatting of pointers in printk()
Use %p instead of %08x in printk().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Make do_execve() take a const filename pointer so that kernel_execve() compiles
correctly on ARM:
arch/arm/kernel/sys_arm.c:88: warning: passing argument 1 of 'do_execve' discards qualifiers from pointer target type
This also requires the argv and envp arguments to be consted twice, once for
the pointer array and once for the strings the array points to. This is
because do_execve() passes a pointer to the filename (now const) to
copy_strings_kernel(). A simpler alternative would be to cast the filename
pointer in do_execve() when it's passed to copy_strings_kernel().
do_execve() may not change any of the strings it is passed as part of the argv
or envp lists as they are some of them in .rodata, so marking these strings as
const should be fine.
Further kernel_execve() and sys_execve() need to be changed to match.
This has been test built on x86_64, frv, arm and mips.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
