| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
arch/arm/kernel/signal.c
drivers/mmc/card/block.c
drivers/mtd/nand/Kconfig
include/linux/amba/mmci.h
kernel/printk.c
mm/shmem.c
net/socket.c
|
|
There is no need to test for a device_type property in ns8250
compatible serial ports. device_type is an OpenFirmware property that
is not required when using the flattened tree representation.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Conflicts:
drivers/usb/core/hcd-pci.c
drivers/usb/host/isp1760-hcd.c
include/linux/usb/ch9.h
|
|
Magic SysRq key is not working for OMAP on new serial
console ttyOx because SUPPORT_SYSRQ is not defined
for omap-serial.
This patch defines SUPPORT_SYSRQ in omap-serial and
enables handling of Magic SysRq character.
Further there is an issue of losing first break character.
Removing the reset of the lsr_break_flag fixes this issue.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Manjunath G Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(cherry picked from commit 364a6ece62455f669336e50d5b00f14ba650da93)
|
|
|
|
Conflicts:
arch/arm/mach-mxs/gpio.c
drivers/usb/gadget/fsl_mxc_udc.c
|
|
commit 0d0389e5414c8950b1613e8bdc74289cde3d6d98 upstream.
In 8250.c original ns16550 autoconfig code, we change the divisor latch when
we goto to high speed mode, we're assuming the previous speed is legacy. This
some times is not true.
For example in a system with both CONFIG_SERIAL_8250 and
CONFIG_SERIAL_8250_PNP set, in this case, the code (autoconfig) will be called
twice, one in serial8250_init/probe() and the other is from
serial_pnp_probe. When serial_pnp_probe calls the autoconfig for NS16550A,
it's already in high speed mode, change the divisor latch (quot << 3) in this
case will make the UART console garbled.
CC: Greg Kroah-Hartman <greg@kroah.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 95926d2db6256e08d06b753752a0d903a0580acc upstream.
For any reason if the NS16550A was not work in high speed mode (e.g. we hold
NS16550A from going to high speed mode in autoconfig_16550a()), now we are
resume from suspend, we should also set the uartclk to the correct
value. Otherwise it is still the old 1843200 and that will bring issues.
CC: Greg Kroah-Hartman <greg@kroah.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d8653d305ef66861c91fa7455fb8038460a7274c upstream.
This is used to store the spi_device ->modalias so they have to be the same
size. SPI_NAME_SIZE is 32.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Resolved Conflicts:
drivers/mmc/core/sdio.c
|
|
|
|
* rmk/for-linus: (1557 commits)
ARM: 6806/1: irq: introduce entry and exit functions for chained handlers
ARM: 6781/1: Thumb-2: Work around buggy Thumb-2 short branch relocations in gas
ARM: 6747/1: P2V: Thumb2 support
ARM: 6798/1: aout-core: zero thread debug registers in a.out core dump
ARM: 6796/1: Footbridge: Fix I/O mappings for NOMMU mode
ARM: 6784/1: errata: no automatic Store Buffer drain on Cortex-A9
ARM: 6772/1: errata: possible fault MMU translations following an ASID switch
ARM: 6776/1: mach-ux500: activate fix for errata 753970
ARM: 6794/1: SPEAr: Append UL to device address macros.
ARM: 6793/1: SPEAr: Remove unused *_SIZE macros from spear*.h files
ARM: 6792/1: SPEAr: Replace SIZE macro's with SZ_4K macros
ARM: 6791/1: SPEAr3xx: Declare device structures after shirq code
ARM: 6790/1: SPEAr: Clock Framework: Rename usbd clock and align apb_clk entry
ARM: 6789/1: SPEAr3xx: Rename sdio to sdhci
ARM: 6788/1: SPEAr: Include mach/hardware.h instead of mach/spear.h
ARM: 6787/1: SPEAr: Reorder #includes in .h & .c files.
ARM: 6681/1: SPEAr: add debugfs support to clk API
ARM: 6703/1: SPEAr: update clk API support
ARM: 6679/1: SPEAr: make clk API functions more generic
ARM: 6737/1: SPEAr: formalized timer support
...
Conflicts:
arch/arm/mach-msm/board-msm7x27.c
arch/arm/mach-msm/board-msm7x30.c
arch/arm/mach-msm/board-qsd8x50.c
arch/arm/mach-msm/board-sapphire.c
arch/arm/mach-msm/include/mach/memory.h
|
|
Conflicts:
arch/arm/mach-exynos4/cpufreq.c
arch/arm/mach-exynos4/irq-eint.c
arch/arm/mach-mx5/clock-mx51-mx53.c
arch/arm/mach-ux500/board-mop500-sdi.c
arch/arm/plat-s5p/Makefile
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into devel-stable
Conflicts:
arch/arm/mm/Kconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-tcc into devel-stable
|
|
|
|
devel-stable
|
|
This piece of code was just slightly different between the DMA
and IRQ paths, in DMA mode we surely shouldn't read more than
256 character either, so factor this out in its own function and
use for both DMA and PIO mode.
Tested on Ux500 and U300.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This adds an optional RX DMA codepath for the devices that
support this by using the apropriate burst sizes instead of
pulling single bytes.
Includes portions of code written by Russell King during
a PL08x hacking session.
This has been tested on U300 and Ux500.
Tested-by: Jerzy Kasenberg <jerzy.kasenberg@tieto.com>
Tested-by: Grzegorz Sygieda <grzegorz.sygieda@tieto.com>
Tested-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Per Forlin <per.friden@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
fmvj18x_cs:add new id
Toshiba lan&modem multifuction card (model name:IPC5010A)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/rtc/Kconfig
Change-Id: I7c1b1711311c008c378774cce1c80bc265f9b0a9
|
|
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
arch/arm/kernel/head.S
|
|
This patch changes dependency of ARCH_EXYNOS4 from ARCH_S5PV310
according to the change of ARCH name, EXYNOS4.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure MAYDAY_INITIAL_TIMEOUT is at least 2 jiffies long
workqueue, freezer: unify spelling of 'freeze' + 'able' to 'freezable'
workqueue: wake up a worker when a rescuer is leaving a gcwq
|
|
There are two spellings in use for 'freeze' + 'able' - 'freezable' and
'freezeable'. The former is the more prominent one. The latter is
mostly used by workqueue and in a few other odd places. Unify the
spelling to 'freezable'.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Steven Whitehouse <swhiteho@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
|
|
The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: matrix_keypad - increase the limit of rows and columns
Input: wacom - fix error path in wacom_probe()
Input: ads7846 - check proper condition when freeing gpio
Revert "Input: do not pass injected events back to the originating handler"
Input: sysrq - rework re-inject logic
Input: serio - clear pending rescans after sysfs driver rebind
Input: rotary_encoder - use proper irqflags
Input: wacom_w8001 - report resolution to userland
|
|
linux/device.h include
Do not include linux/device.h twice in drivers/tty/serial/mxs-auart.c .
Once is enough.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Conflicts:
arch/arm/mach-mxs/clock-mx28.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The RX lock is used to protect the RX buffer from concurrent access in DMA
mode between the timer and RX interrupt routines. It is independent from
the uart lock which is used to protect the TX buffer. It is possible for
a uart TX transfer to be started up from the RX interrupt handler if low
latency is enabled. So we need to split the locks to avoid deadlocking in
this situation.
In PIO mode, the RX lock is not necessary because the handle_simple_irq
and handle_level_irq functions ensure driver interrupt handlers are called
once on one core.
And now that the RX path has its own lock, the TX interrupt has nothing to
do with the RX path, so disabling it at the same time.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Commit 0587102cf9f427c185bfdeb2cef41e13ee0264b1 replaced a direct
implementation of SIOCGICOUNT with an implementation of
tty_operations::get_icount, but it did not actually set
rs_360_ops.get_icount.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org [2.6.37]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This field is settable but did not get copied.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Commit 728674a7e466628df2aeec6d11a2ae1ef968fb67 moved virtio_console.c
to drivers/tty/hvc/ under the perception of this being an hvc driver.
It was such once, but these days it has generic communication
capabilities as well, so move it to drivers/char/.
In the future, the hvc part from this file can be split off and moved
under drivers/tty/hvc/.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
UART TX. The idea here is to provide a mechanism where we can wakeup our peer before sending data.
Signed-off-by: San Mehat <san@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/serial: fix apbuart build
n_hdlc: fix read and write locking
serial: unbreak billionton CF card
tty: use for_each_console() and WARN() on sysfs failures
vt: fix issue when fbcon wants to takeover a second time.
Fix up trivial conflict in drivers/tty/tty_io.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
|
|
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* msm-uart:
serial: msm: Add support for UARTDM cores
msm: Add name field to UART resources
|
|
Fix build errors by selecting SERIAL_CORE:
ERROR: "uart_register_driver" [drivers/tty/serial/apbuart.ko] undefined!
ERROR: "uart_write_wakeup" [drivers/tty/serial/apbuart.ko] undefined!
ERROR: "uart_update_timeout" [drivers/tty/serial/apbuart.ko] undefined!
ERROR: "uart_get_divisor" [drivers/tty/serial/apbuart.ko] undefined!
ERROR: "uart_get_baud_rate" [drivers/tty/serial/apbuart.ko] undefined!
ERROR: "uart_add_one_port" [drivers/tty/serial/apbuart.ko] undefined!
ERROR: "uart_unregister_driver" [drivers/tty/serial/apbuart.ko] undefined!
ERROR: "uart_remove_one_port" [drivers/tty/serial/apbuart.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix locking in read and write code of n_hdlc line discipline.
2.6.36 replaced lock_kernel() with tty_lock(). The tty mutex is not
dropped automatically when the thread sleeps like the BKL. This results
in a blocked read or write holding the tty mutex and stalling operations
by other devices that use the tty mutex.
A review of n_hdlc read and write code shows:
1. neither BKL or tty mutex are required for correct operation
2. read can block while read data is available if data is posted
between availability check and call to interruptible_sleep_on()
3. write does not set process state to TASK_INTERRUPTIBLE
on each pass through the processing loop which can cause
unneeded scheduling of the thread
The unnecessary tty mutex references have been removed.
Read changed to use same code as n_tty read
for completing reads and blocking.
Write corrected to set process state to TASK_INTERRUPTIBLE on each pass
through processing loop.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Unbreak Billionton CF bluetooth card. This actually fixes a regression
on zaurus.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This fixes the build warnings in the tty code, and uses the proper
function for iterating over the console devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
With framebuffer handover and multiple GPUs, we get into a
position where the fbcon unbinds the vesafb framebuffer for GPU 1,
but we still have a radeon framebuffer bound from GPU 0, so
we don't unregister the console driver. Then when we tried to bind
the new radeon framebuffer for GPU1 we never get to the bind
call as we fail due to the console being registered already.
This changes the return value to -EBUSY when the driver is
already registered and continues to bind for -EBUSY.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* akpm:
kernel/smp.c: consolidate writes in smp_call_function_interrupt()
kernel/smp.c: fix smp_call_function_many() SMP race
memcg: correctly order reading PCG_USED and pc->mem_cgroup
backlight: fix 88pm860x_bl macro collision
drivers/leds/ledtrig-gpio.c: make output match input, tighten input checking
MAINTAINERS: update Atmel AT91 entry
mm: fix truncate_setsize() comment
memcg: fix rmdir, force_empty with THP
memcg: fix LRU accounting with THP
memcg: fix USED bit handling at uncharge in THP
memcg: modify accounting function for supporting THP better
fs/direct-io.c: don't try to allocate more than BIO_MAX_PAGES in a bio
mm: compaction: prevent division-by-zero during user-requested compaction
mm/vmscan.c: remove duplicate include of compaction.h
memblock: fix memblock_is_region_memory()
thp: keep highpte mapped until it is no longer needed
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: update MAINTAINERS file due to driver movement
tty: move drivers/serial/ to drivers/tty/serial/
tty: move hvc drivers to drivers/tty/hvc/
|
