| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull hwmon updates from Jean Delvare:
"We have support for the MCP3021, MC13892 and GMT G781, automatic fan
speed control for LM63/LM64 chips, and a few clean-ups."
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Add MCP3021 ADC driver
hwmon: (mc13783-adc) Add support for the MC13892 PMIC
hwmon: (mc13783-adc) Remove space before tab
hwmon: (lm63) Let the user adjust the lookup table
hwmon: (lm63) Make fan speed control strategy changeable
hwmon: (lm63) Reorganize the code
hwmon: (lm90) Restore original configuration if probe function fails
hwmon: (lm90) Add support for GMT G781
hwmon: (lm90) Fix multi-line comments
hwmon: (w83795) Fix multi-line comments
hwmon: (w83795) Unconditionally support manual fan speed control
hwmon: (fam15h_power) Increase output resolution
hwmon: (fam15h_power) Correct sign extension of running_avg_capture
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"The IOMMU updates for this round are not very large patch-wise. But
they contain two new IOMMU drivers for the ARM Tegra 2 and 3
platforms. Besides that there are also a few patches for the AMD
IOMMU which prepare the driver for adding intr-remapping support and a
couple of fixes."
* tag 'iommu-updates-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix section mismatch
iommu/amd: Move interrupt setup code into seperate function
iommu/amd: Make sure IOMMU interrupts are re-enabled on resume
iommu/amd: Fix section warning for prealloc_protection_domains
iommu/amd: Don't initialize IOMMUv2 resources when not required
iommu/amd: Update git-tree in MAINTAINERS
iommu/tegra-gart: fix spin_unlock in map failure path
iommu/amd: Fix double free of mem-region in error-path
iommu/amd: Split amd_iommu_init function
ARM: IOMMU: Tegra30: Add iommu_ops for SMMU driver
ARM: IOMMU: Tegra20: Add iommu_ops for GART driver
|
|
Pull i2c embedded updates from Wolfram Sang:
"Nothing special from i2c-embedded for this merge window. Two new
drivers, minor feature additions, bugfixes, cleanups.
All patches have been in linux-next for some time, too."
* 'i2c-embedded/for-3.4' of git://git.pengutronix.de/git/wsa/linux:
i2c-eg20t: Remove write-only variables
i2c-eg20t: Rework pch_i2c_wait_for_bus_idle to reduce wait time
i2c-s3c2410: Add stub runtime power management
i2c-s3c2410: Convert to devm_kzalloc()
i2c: add CSR SiRFprimaII on-chip I2C controllers driver
i2c: tegra: Remove unnecessary write to INT_STATUS
i2c: imx: fix imx driver to work though signal is pending
i2c: designware: dw_i2c_init_driver as subsys initcall
misc: at24: describe platform_data with kernel_doc
i2c: Move I2C_EG20T option to the right place.
i2c: Support for Netlogic XLR/XLS I2C controller.
i2c: mpc: Add support for SMBUS_READ_BLOCK_DATA
i2c: versatile: Add Device Tree support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
|
|
Pull networking fixes from David Miller:
1) L2TP doesn't get autoloaded when you try to open an L2TP socket due
to a missing module alias, fix from Benjamin LaHaise.
2) Netlabel and RDS should propagate gfp flags given to them by
callers, fixes from Dan Carpeneter.
3) Recursive locking fix in usbnet wasn't bulletproof and can result in
objects going away mid-flight due to races, fix from Ming Lei.
4) Fix up some confusion about a bool module parameter in netfilter's
iptable_filter and ip6table_filter, from Rusty Russell.
5) If SKB recycling is used via napi_reuse_skb() we end up with
different amounts of headroom reserved than we had at the original
SKB allocation. Fix from Eric Dumazet.
6) Fix races in TG3 driver ring refilling, from Michael Chan.
7) We have callbacks for IPSEC replay notifiers, but some call sites
were not using the ops method and instead were calling one of the
implementations directly. Oops. Fix from Steffen Klassert.
8) Fix IP address validation properly in the bonding driver, the
previous fix only works with netlink where the subnet mask and IP
address are changed in one atomic operation. When 'ifconfig' ioctls
are used the IP address and the subnet mask are changed in two
distinct operations. Fix from Andy Gospodarek.
9) Provide a sky2 module operation to work around power management
issues with some BIOSes. From Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
usbnet: consider device busy at each recieved packet
bonding: remove entries for master_ip and vlan_ip and query devices instead
netfilter: remove forward module param confusion.
usbnet: don't clear urb->dev in tx_complete
usbnet: increase URB reference count before usb_unlink_urb
xfrm: Access the replay notify functions via the registered callbacks
xfrm: Remove unused xfrm_state from xfrm_state_check_space
RDS: use gfp flags from caller in conn_alloc()
netlabel: use GFP flags from caller instead of GFP_ATOMIC
l2tp: enable automatic module loading for l2tp_ppp
cnic: Fix parity error code conflict
tg3: Fix RSS ring refill race condition
sky2: override for PCI legacy power management
net: fix napi_reuse_skb() skb reserve
|
|
Pull UBI changes from Artem Bityutskiy:
- Reduce memory consumption
- Fix picking unknown blocks
- Fix error-path in 'ubi_scan()'
- Minor clean-ups
* tag 'upstream-3.4-rc1' of git://git.infradead.org/linux-ubi:
UBI: rename MOVE_CANCEL_BITFLIPS to MOVE_TARGET_BITFLIPS
UBI: rename peb_buf1 to peb_buf
UBI: reduce memory consumption
UBI: fix eraseblock picking criteria
UBI: fix documentation and improve readability
UBI: fix error handling in ubi_scan()
|
|
Add I2C driver for MCP3021 that is an ADC chip from Microchip.
The MCP3021 is a successive approximation A/D converter (ADC)
with 10-bit resolution.
The driver export the value of Vin to sysfs, the voltage unit is
mV. Through the sysfs interface, lm-sensors tool can also display
Vin voltage.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Based on a patch by David Jander that mostly did s/mc13783/mc13xxx/ .
Additionally use dev_get_drvdata instead of to_platform_device +
platform_get_drvdata in mc13783_adc_read (spotted by Jean Delvare).
Cc: David Jander <david.jander@protonic.nl>
Signed-off-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Make the automatic fan speed control lookup table writable. This lets
the user tweak the fan speed / temperature response curve.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Let the user switch between automatic and manual fan speed control.
Before switching to automatic fan speed control, we always check that
the lookup table looks sane.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Reorder functions and driver declaration to no longer need to
forward-declare functions. Also rename new_client to just client
everywhere for readability.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The lm90 driver restores the original chip configuration in its exit function.
However, the chip configuration is not restored if the probe function fails.
Restore it there as well.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
GMT G781 is a ADM1032-compatible temperature sensor chip.
Add support to the LM90 driver.
Cc: Mike Gorchak <lestat@i.com.ua>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Manual fan speed control uses a standard interface and has received
sufficient testing and review by now, it can be enabled
unconditionally. This includes attributes pwm[1-8], pwm[1-8]_enable,
pwm[1-8]_mode and pwm[1-8]_freq.
We only let the user switch from automatic mode to manual mode, but
not the other way around, as automatic control settings may not have
been set properly by the BIOS.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
On high CPU load the accumulating values in the running_avg_cap
register are very low (below 10), so averaging them too early leads
to unnecessary poor output resolution. Since we pretend to output
micro-Watt we better keep all the bits we have as long as possible.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Wrong bit was used for sign extension which caused wrong end results.
Thanks to Andre for spotting this bug.
Reported-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org
|
|
Pull fbdev updates for 3.4 from Florian Tobias Schandinat:
- drivers for Samsung Exynos MIPI DSI and display port
- i740fb to support those old Intel chips
- large updates to OMAP, viafb and sh_mobile_lcdcfb
- some updates to s3c-fb and udlfb, few patches to others
Fix up conflicts in drivers/video/udlfb.c due to Key Sievers' fix making
it in twice.
* tag 'fbdev-updates-for-3.4' of git://github.com/schandinat/linux-2.6: (156 commits)
Revert "video:uvesafb: Fix oops that uvesafb try to execute NX-protected page"
OMAPDSS: register dss drivers in module init
video: pxafb: add clk_prepare/clk_unprepare calls
fbdev: bfin_adv7393fb: Drop needless include
fbdev: sh_mipi_dsi: add extra phyctrl for sh_mipi_dsi_info
fbdev: remove dependency of FB_SH_MOBILE_MERAM from FB_SH_MOBILE_LCDC
Revert "MAINTAINERS: add entry for exynos mipi display drivers"
fbdev: da8xx: add support for SP10Q010 display
fbdev: da8xx:: fix reporting of the display timing info
drivers/video/pvr2fb.c: ensure arguments to request_irq and free_irq are compatible
OMAPDSS: APPLY: fix clearing shadow dirty flag with manual update
fbdev: sh_mobile_meram: Implement system suspend/resume
fbdev: sh_mobile_meram: Remove unneeded sanity checks
fbdev: sh_mobile_meram: Don't perform update in register operation
arm: mach-shmobile: Constify sh_mobile_meram_cfg structures
fbdev: sh_mobile_lcdc: Don't store copy of platform data
fbdev: sh_mobile_meram: Remove unused sh_mobile_meram_icb_cfg fields
arm: mach-shmobile: Don't set MERAM ICB numbers in platform data
fbdev: sh_mobile_meram: Allocate ICBs automatically
fbdev: sh_mobile_meram: Use genalloc to manage MERAM allocation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Things are really quieting down with the regmap API, while we're still
seeing a trickle of new features coming in they're getting much
smaller than they were. It's also nice to have some features which
support other subsystems building infrastructure on top of regmap.
Highlights include:
- Support for padding between the register and the value when
interacting with the device, sometimes needed for fast interfaces.
- Support for applying register updates to the device when restoring
the register state. This is intended to be used to apply updates
supplied by manufacturers for tuning the performance of the device
(many of which are to undocumented registers which aren't otherwise
covered).
- Support for multi-register operations on cached registers.
- Support for syncing only part of the register cache.
- Stubs and parameter query functions intended to make it easier for
other subsystems to build infrastructure on top of the regmap API.
plus a few driver updates making use of the new features which it was
easier to merge via this tree."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (41 commits)
regmap: Fix future missing prototype of devres_alloc() and friends
regmap: Rejig struct declarations for stubbed API
regmap: Fix rbtree block base in sync
regcache: Make sure we sync register 0 in an rbtree cache
regmap: delete unused module.h from drivers/base/regmap files
regmap: Add stub for regcache_sync_region()
mfd: Improve performance of later WM1811 revisions
regmap: Fix x86_64 breakage
regmap: Allow drivers to sync only part of the register cache
regmap: Supply ranges to the sync operations
regmap: Add tracepoints for cache only and cache bypass
regmap: Mark the cache as clean after a successful sync
regmap: Remove default cache sync implementation
regmap: Skip hardware defaults for LZO caches
regmap: Expose the driver name in debugfs
mfd: wm8400: Convert to devm_regmap_init_i2c()
mfd: wm831x: Convert to devm_regmap_init()
mfd: wm8994: Convert to devm_regmap_init()
mfd/ASoC: Convert WM8994 driver to use regmap patches
mfd: Add __devinit and __devexit annotations in wm8994
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull IEEE 1394 (FireWire) subsystem updates post v3.3 from Stefan Richter:
- Some SBP-2 initiator fixes, side product from ongoing work on a target.
- Reintroduction of an isochronous I/O feature of the older ieee1394 driver
stack (flush buffer completions); it was evidently rarely used but not
actually unused. Matching libraw1394 code is already available.
- Be sure to prefix all kernel log messages with device name or card name,
and other logging related cleanups.
- Misc other small cleanups, among them a small API change that affects
sound/firewire/ too. Clemens Ladisch is aware of it.
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394: (26 commits)
firewire: allow explicit flushing of iso packet completions
firewire: prevent dropping of completed iso packet header data
firewire: ohci: factor out iso completion flushing code
firewire: ohci: simplify iso header pointer arithmetic
firewire: ohci: optimize control bit checks
firewire: ohci: remove unused excess_bytes field
firewire: ohci: copy_iso_headers(): make comment match the code
firewire: cdev: fix IR multichannel event documentation
firewire: ohci: fix too-early completion of IR multichannel buffers
firewire: ohci: move runtime debug facility out of #ifdef
firewire: tone down some diagnostic log messages
firewire: sbp2: replace a GFP_ATOMIC allocation
firewire: sbp2: Fix SCSI sense data mangling
firewire: sbp2: Ignore SBP-2 targets on the local node
firewire: sbp2: Take into account Unit_Unique_ID
firewire: nosy: Use the macro DMA_BIT_MASK().
firewire: core: convert AR-req handler lock from _irqsave to _bh
firewire: core: fix race at address_handler unregistration
firewire: core: remove obsolete comment
firewire: core: prefix log messages with card name
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates for v3.4 from Linus Walleij (*):
- Switches the PXA 168, 910 and MMP over to use pinctrl
- Locking revamped
- Massive refactorings...
- Reform the driver API to use multiple states
- Support pin config in the mapping tables
- Pinctrl drivers for the nVidia Tegra series
- Generic pin config support lib for simple pin controllers
- Implement pin config for the U300
* tag 'pinctrl-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
ARM: u300: configure some pins as an example
pinctrl: support pinconfig on the U300
pinctrl/coh901: use generic pinconf enums and parameters
pinctrl: introduce generic pin config
pinctrl: fix error path in pinconf_map_to_setting()
pinctrl: allow concurrent gpio and mux function ownership of pins
pinctrl: forward-declare struct device
pinctrl: split pincontrol states into its own header
pinctrl: include machine header to core.h
ARM: tegra: Select PINCTRL Kconfig variables
pinctrl: add a driver for NVIDIA Tegra
pinctrl: Show selected function and group in pinmux-pins debugfs
pinctrl: enhance mapping table to support pin config operations
pinctrl: API changes to support multiple states per device
pinctrl: add usecount to pins for muxing
pinctrl: refactor struct pinctrl handling in core.c vs pinmux.c
pinctrl: fix and simplify locking
pinctrl: fix the pin descriptor kerneldoc
pinctrl: assume map table entries can't have a NULL name field
pinctrl: introduce PINCTRL_STATE_DEFAULT, define hogs as that state
...
(*) What is it with all these Linuses these days? There's a Linus at
google too. Some day I will get myself my own broadsword, and run
around screaming "There can be only one".
I used to be _special_ dammit. Snif.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata updates from Jeff Garzik:
1) AHCI regression fix. A recent "make driver conform to spec" change
broke on deployed hardware. Make new behavior optional, rather than
default, turning it on only for specific embedded platforms that
need this.
Everybody else runs in the famous "non conformant but working" mode.
2) pata_cmd64x, pata_legacy cleanups
3) new Intel SATA PCI IDs
4) misc minor vendor feature additions
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_cmd64x: implement sff_irq_check() method
pata_cmd64x: implement sff_irq_clear() method
pata_cmd64x: use interrupt status from MRDMODE register
pata_cmd64x: turn string of *if* statements into *switch*
drivers/ata/pata_mpc52xx.c: clean up error handling code
ahci_platform: add STRICT_AHCI platform type
ahci: move AHCI_HFLAGS() macro to ahci.h
ahci: add AHCI_HFLAG_DELAY_ENGINE host flag
sata_fsl: add support for interrupt coalsecing feature
ata/pata_arasan_cf: Add Hibernation support
pata_legacy: correctly mask recovery field for HT6560B
ata_piix: IDE-mode SATA patch for Intel Lynx Point DeviceIDs
ahci: AHCI-mode SATA patch for Intel Lynx Point DeviceIDs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov:
"- we finally merged driver for USB version of Synaptics touchpads
(I guess most commonly found in IBM/Lenovo keyboard/touchpad combo);
- a bunch of new drivers for embedded platforms (Cypress
touchscreens, DA9052 OnKey, MAX8997-haptic, Ilitek ILI210x
touchscreens, TI touchscreen);
- input core allows clients to specify desired clock source for
timestamps on input events (EVIOCSCLOCKID ioctl);
- input core allows querying state of all MT slots for given event
code via EVIOCGMTSLOTS ioctl;
- various driver fixes and improvements."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: ili210x - add support for Ilitek ILI210x based touchscreens
Input: altera_ps2 - use of_match_ptr()
Input: synaptics_usb - switch to module_usb_driver()
Input: convert I2C drivers to use module_i2c_driver()
Input: convert SPI drivers to use module_spi_driver()
Input: omap4-keypad - move platform_data to <linux/platform_data>
Input: kxtj9 - who_am_i check value and initial data rate fixes
Input: add driver support for MAX8997-haptic
Input: tegra-kbc - revise device tree support
Input: of_keymap - add device tree bindings for simple key matrices
Input: wacom - fix physical size calculation for 3rd-gen Bamboo
Input: twl4030-vibra - really switch from #if to #ifdef
Input: hp680_ts_input - ensure arguments to request_irq and free_irq are compatible
Input: max8925_onkey - avoid accessing input device too early
Input: max8925_onkey - allow to be used as a wakeup source
Input: atmel-wm97xx - convert to dev_pm_ops
Input: atmel-wm97xx - set driver owner
Input: add cyttsp touchscreen maintainer entry
Input: cyttsp - remove useless checks in cyttsp_probe()
Input: usbtouchscreen - add support for Data Modul EasyTouch TP 72037
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen updates from Konrad Rzeszutek Wilk:
"which has three neat features:
- PV multiconsole support, so that there can be hvc1, hvc2, etc; This
can be used in HVM and in PV mode.
- P-state and C-state power management driver that uploads said power
management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
There is one thing in the Kconfig that you won't like: "default y
if (X86_ACPI_CPUFREQ = y || X86_POWERNOW_K8 = y)" (note, that it
all depends on CONFIG_XEN which depends on CONFIG_PARAVIRT which by
default is off). I've a fix to convert that boolean expression
into "default m" which I am going to post after the cpufreq git
pull - as the two patches to make this work depend on a fix in Dave
Jones's tree.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx"
Fix up trivial conflicts in drivers/tty/hvc/hvc_xen.c due to changes to
a removed commit.
* tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen kconfig: relax INPUT_XEN_KBDDEV_FRONTEND deps
xen/acpi-processor: C and P-state driver that uploads said data to hypervisor.
xen: constify all instances of "struct attribute_group"
xen/xenbus: ignore console/0
hvc_xen: introduce HVC_XEN_FRONTEND
hvc_xen: implement multiconsole support
hvc_xen: support PV on HVM consoles
xenbus: don't free other end details too early
xen/enlighten: Expose MWAIT and MWAIT_LEAF if hypervisor OKs it.
xen/setup/pm/acpi: Remove the call to boot_option_idle_override.
xenbus: address compiler warnings
xen: use this_cpu_xxx replace percpu_xxx funcs
xen/pciback: Support pci_reset_function, aka FLR or D3 support.
pci: Introduce __pci_reset_function_locked to be used when holding device_lock.
xen: Utilize the restore_msi_irqs hook.
|
|
usbnet should centrally handle busy reporting in the rx path
so subdrivers need not worry. This hurts use cases which do
rx only or predominantly.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm
Pull cleancache changes from Konrad Rzeszutek Wilk:
"This has some patches for the cleancache API that should have been
submitted a _long_ time ago. They are basically cleanups:
- rename of flush to invalidate
- moving reporting of statistics into debugfs
- use __read_mostly as necessary.
Oh, and also the MAINTAINERS file change. The files (except the
MAINTAINERS file) have been in #linux-next for months now. The late
addition of MAINTAINERS file is a brain-fart on my side - didn't
realize I needed that just until I was typing this up - and I based
that patch on v3.3 - so the tree is on top of v3.3."
* tag 'stable/for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm:
MAINTAINERS: Adding cleancache API to the list.
mm: cleancache: Use __read_mostly as appropiate.
mm: cleancache: report statistics via debugfs instead of sysfs.
mm: zcache/tmem/cleancache: s/flush/invalidate/
mm: cleancache: s/flush/invalidate/
|
|
The following patch aimed to resolve an issue where secondary, tertiary,
etc. addresses added to bond interfaces could overwrite the
bond->master_ip and vlan_ip values.
commit 917fbdb32f37e9a93b00bb12ee83532982982df3
Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
Date: Wed Nov 23 23:37:15 2011 +0000
bonding: only use primary address for ARP
That patch was good because it prevented bonds using ARP monitoring from
sending frames with an invalid source IP address. Unfortunately, it
didn't always work as expected.
When using an ioctl (like ifconfig does) to set the IP address and
netmask, 2 separate ioctls are actually called to set the IP and netmask
if the mask chosen doesn't match the standard mask for that class of
address. The first ioctl did not have a mask that matched the one in
the primary address and would still cause the device address to be
overwritten. The second ioctl that was called to set the mask would
then detect as secondary and ignored, but the damage was already done.
This was not an issue when using an application that used netlink
sockets as the setting of IP and netmask came down at once. The
inconsistent behavior between those two interfaces was something that
needed to be resolved.
While I was thinking about how I wanted to resolve this, Ralf Zeidler
came with a patch that resolved this on a RHEL kernel by keeping a full
shadow of the entries in dev->ifa_list for the bonding device and vlan
devices in the bonding driver. I didn't like the duplication of the
list as I want to see the 'bonding' struct and code shrink rather than
grow, but liked the general idea.
As the Subject indicates this patch drops the master_ip and vlan_ip
elements from the 'bonding' and 'vlan_entry' structs, respectively.
This can be done because a device's address-list is now traversed to
determine the optimal source IP address for ARP requests and for checks
to see if the bonding device has a particular IP address. This code
could have all be contained inside the bonding driver, but it made more
sense to me to EXPORT and call inet_confirm_addr since it did exactly
what was needed.
I tested this and a backported patch and everything works as expected.
Ralf also helped with verification of the backported patch.
Thanks to Ralf for all his help on this.
v2: Whitespace and organizational changes based on suggestions from Jay
Vosburgh and Dave Miller.
v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's
suggestion.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Ralf Zeidler <ralf.zeidler@nsn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"The biggest patch is the rework of the smp code, something I wanted to
do for some time. There are some patches for our various dump methods
and one new thing: z/VM LGR detection. LGR stands for linux-guest-
relocation and is the guest migration feature of z/VM. For debugging
purposes we keep a log of the systems where a specific guest has lived."
Fix up trivial conflict in arch/s390/kernel/smp.c due to the scheduler
cleanup having removed some code next to removed s390 code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] kernel: Pass correct stack for smp_call_ipl_cpu()
[S390] Ensure that vmcore_info pointer is never accessed directly
[S390] dasd: prevent validate server for offline devices
[S390] Remove monolithic build option for zcrypt driver.
[S390] stack dump: fix indentation in output
[S390] kernel: Add OS info memory interface
[S390] Use block_sigmask()
[S390] kernel: Add z/VM LGR detection
[S390] irq: external interrupt code passing
[S390] irq: set __ARCH_IRQ_EXIT_IRQS_DISABLED
[S390] zfcpdump: Implement async sdias event processing
[S390] Use copy_to_absolute_zero() instead of "stura/sturg"
[S390] rework idle code
[S390] rework smp code
[S390] rename lowcore field
[S390] Fix gcc 4.6.0 compile warning
|
|
URB unlinking is always racing with its completion and tx_complete
may be called before or during running usb_unlink_urb, so tx_complete
must not clear urb->dev since it will be used in unlink path,
otherwise invalid memory accesses or usb device leak may be caused
inside usb_unlink_urb.
Cc: stable@kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock, but it makes usb_unlink_urb
racing with defer_bh, and the URB to being unlinked may be freed before
or during calling usb_unlink_urb, so use-after-free problem may be
triggerd inside usb_unlink_urb.
The patch fixes the use-after-free problem by increasing URB
reference count with skb queue lock held before calling
usb_unlink_urb, so the URB won't be freed until return from
usb_unlink_urb.
Cc: stable@kernel.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~airlied/linux
Pull nouveau destaging + Kelper modesetting support from Dave Airlie:
"This pull request is unexpected and not something I had mentioned
previously.
So NVIDIA announced new Kepler GPUs this morning, and Ben has killed
himself getting modesetting support for them together to have on
launch day. Most of the code to support the new chips has already
gone in, however this pull contains a few more pieces along with the
final enables so the driver binds to the new Kepler cards. Its quite
amazing that nouveau can support a GPU on its launch day even if its
just unaccelerated modesetting, and I'd like to have support in the
next kernel.
In order to sweeten the deal, Ben has also requested nouveau destage
and become ABI stable, the only change is the version number bump
which he prepared userspace for quite a long time ago. The driver
hasn't broken ABI since that one big break that caused a lot of fuss.
It's also quite a small set of code, and not likely to break anything."
* 'drm-nouveau-destage' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/dp: support version 4.0 of DP table
drm/nve0/disp: nvidia randomly decided to move the dithering method
drm/nve0: initial modesetting support for kepler chipsets
drm/nouveau: add bios connector type for dms59
drm/nouveau: move out of staging drivers
drm/nouveau: bump version to 1.0.0
drm/nvd0/disp: ignore clock set if no pclk
drm/nouveau: oops, increase channel dispc_vma to 4
drm/nouveau: inform userspace of new kernel subchannel requirements
drm/nouveau: remove m2mf creation on userspace channels
drm/nvc0-/disp: reimplement flip completion method as fifo method
drm/nouveau: move fence sequence check to start of loop
drm/nouveau: remove subchannel names from places where it doesn't matter
drm/nouveau/ttm: always do buffer moves on kernel channel
|
|
git://people.freedesktop.org/~airlied/linux
Pull radeon southern islands / trinity support from Dave Airlie:
"This is support from AMD for their newest GPU and APUs. The products
called RadeonHD 7xxx, and the Trinity APU series.
This did come in a bit late, due to some over-complicated AMD internal
review process, which from the outside seems unnecessary once the
company has decided it wants to support open source. However as I
said previously I'd rather not put the people who've got this hw for 3
months now being forced to use fglrx on it if there is open code.
Its pretty well self contained and just plugs into the driver in
various places."
* 'drm-radeon-sitn-support' of git://people.freedesktop.org/~airlied/linux: (48 commits)
drm/radeon/kms: update duallink checks for DCE6
drm/radeon/kms: add trinity pci ids
drm/radeon/kms: add radeon_asic struct for trinity
drm/radeon/kms: add support for ucode loading on trinity (v2)
drm/radeon/kms/vm: set vram base offset properly for TN
drm/radeon/kms: Update evergreen functions for trinity
drm/radeon/kms: cayman gpu init updates for trinity
drm/radeon/kms: Add checks for TN in the DP bridge code
drm/radeon/kms/DCE6.1: ss is not supported on the internal pplls
drm/radeon/kms: disable PPLL0 on DCE6.1 when not in use
drm/radeon/kms: Adjust pll picker for DCE6.1
drm/radeon/kms: DCE6.1 disp eng pll updates
drm/radeon/kms: DCE6.1 watermark updates for TN
drm/radeon/kms: no support for internal thermal sensor on TN yet
drm/radeon/kms: add trinity (TN) chip family
drm/radeon/kms: Add SI pci ids
drm/radeon: Update radeon_info_ioctl for SI. (v2)
drm/radeon/kms: add radeon_asic struct for SI
drm/radeon/kms: add support for compute rings in CS ioctl on SI
drm/radeon/kms: fill in startup/shutdown callbacks for SI
...
|
|
Pull drm main changes from Dave Airlie:
"This is the main drm pull request, I'm probably going to send two more
smaller ones, will explain below.
This contains a patch that is also in the fbdev tree, but it should be
the same patch, it added an API for hot unplugging framebuffer
devices, and I need that API for a new driver.
It also contains some changes to the i2c tree which Jean has acked,
and one change to moorestown platform stuff in x86.
Highlights:
- new drivers: UDL driver for USB displaylink devices, kms only,
should support correct hotplug operations.
- core: i2c speedups + better hotplug support, EDID overriding via
firmware interface - allows user to load a firmware for a broken
monitor/kvm from userspace, it even has documentation for it.
- exynos: new HDMI audio + hdmi 1.4 + virtual output driver
- gma500: code cleanup
- radeon: cleanups, CS optimisations, streamout support and pageflip
fix
- nouveau: NVD9 displayport support + more reclocking work
- i915: re-enabling GMBUS, finish gpu patch (might help hibernation
who knows), missed irq fixes, stencil tiling fixes, interlaced
support, aliasesd PPGTT support for SNB/IVB, swizzling for SNB/IVB,
semaphore fixes
As well as the usual bunch of cleanups and fixes all over the place.
I've got two things I'd like to merge a bit later:
a) AMD support for all their new radeonhd 7000 series GPU and APUs.
AMD dropped this a bit late due to insane internal review
processes, (please AMD just follow Intel and let open source guys
ship stuff early) however I don't want to penalise people who own
this hardware (since its been on sale for 3-4 months and GPU hw
doesn't exactly have a lifetime in years) and consign them to
using closed drivers for longer than necessary. The changes are
well contained and just plug into the driver new gpu functionality
so they should be fairly regression proof. I just want to give
them a bit of a run on the hw AMD kindly sent me.
b) drm prime/dma-buf interface code. This is just infrastructure
code to expose the dma-buf stuff to drm drivers and to userspace.
I'm not planning on pushing any driver support in this cycle
(except maybe exynos), but I'd like to get the infrastructure code
in so for the next cycle I can start getting the driver support
into the individual drivers. We have started driver support for
i915, nouveau and udl along with I think exynos and omap in
staging. However this code relies on the dma-buf tree being
pulled into your tree first since it needs the latest interfaces
from that tree. I'll push to get that tree sent asap.
(oh and any warnings you see in i915 are gcc's fault from what anyone
can see)."
Fix up trivial conflicts in arch/x86/platform/mrst/mrst.c due to the new
msic_thermal_platform_data() thermal function being added next to the
tc35876x_platform_data() i2c device function..
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (326 commits)
drm/i915: use DDC_ADDR instead of hard-coding it
drm/radeon: use DDC_ADDR instead of hard-coding it
drm: remove unneeded redefinition of DDC_ADDR
drm/exynos: added virtual display driver.
drm: allow loading an EDID as firmware to override broken monitor
drm/exynos: enable hdmi audio feature
drm/exynos: add default pixel format for plane
drm/exynos: cleanup exynos_hdmi.h
drm/exynos: add is_local member in exynos_drm_subdrv struct
drm/exynos: add subdrv open/close functions
drm/exynos: remove module of exynos drm subdrv
drm/exynos: release pending pageflip events when closed
drm/exynos: added new funtion to get/put dma address.
drm/exynos: update gem and buffer framework.
drm/exynos: added mode_fixup feature and code clean.
drm/exynos: add HDMI version 1.4 support
drm/exynos: remove exynos_mixer.h
gma500: Fix mmap frambuffer
drm/radeon: Drop radeon_gem_object_(un)pin.
drm/radeon: Restrict offset for legacy display engine.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull updates of sound stuff from Takashi Iwai:
"Here is the first big update chunk of sound stuff for 3.4-rc1.
In the common sound infrastructure, there are a few changes for
dynamic PCM support (used in ASoC) and a few clean-ups. Majority of
changes are found, as usual, in HD-audio and ASoC.
Some highlights of HD-audio changes:
- All the long-standing static quirk codes for Realtek codec were
finally removed by fixing and extending the Realtek auto-parser.
- The mute-LED control is standardized over all HD-audio codec
drivers using the extended vmaster hook.
- The vmaster slave mixer elements are initialized to 0dB as default
so that the user won't be annoyed by the silent output after
updates, e.g. due to the additions of new elements.
- Other many fix-ups for the misc HD-audio devices.
In the ASoC side, this is a very active release, including a quite a
few framework enhancements. Some highlights:
- Support for widgets not associated with a CODEC, an important part
of the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based
DMA drivers contributed by Lars-Peter Clausen. This will save a
lot of code and make it much easier to deploy enhancements to
dmaengine.
- Support for binary controls, used for providing runtime
configuration of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do
without any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much
effort to put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to
DMAEngine.
- Conversion of EP93xx drivers to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics
WM2200.
- Move audmux driver from arc/arm to sound/soc
- McBSP move from arch/ to sound/ and updates
Also, a few small updates and fixes for other drivers like au88x0,
ymfpci, USB 6fire, USB usx2yaudio are included."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (446 commits)
ASoC: wm8994: Provide VMID mode control and fix default sequence
ASoC: wm8994: Add missing break in resume
ASoC: wm_hubs: Don't actively manage LINEOUT_VMID_BUF
ASoC: pxa-ssp: atomically set stream active masks
ASoC: fsl: p1022ds: tell the WM8776 codec driver that it's the master
ASoC: Samsung: Added to support mono recording
ALSA: hda - Fix build with CONFIG_PM=n
ALSA: au88x0 - Avoid possible Oops at unbinding
ALSA: usb-audio - Fix build error by consitification of rate list
ASoC: core: Fix obscure leak of runtime array
ALSA: pcm - Avoid GFP_ATOMIC in snd_pcm_link()
ALSA: pcm: Constify the list in snd_pcm_hw_constraint_list
ASoC: wm8996: Add 44.1kHz support
ALSA: hda - Fix build of patch_sigmatel.c without CONFIG_SND_HDA_POWER_SAVE
ASoC: mx27vis-aic32x4: Convert it to platform driver
ALSA: hda - fix printing of high HDMI sample rates
ALSA: ymfpci - Fix legacy registers on S3/S4 resume
ALSA: control - Fixe a trailing white space error
ALSA: hda - Add expose_enum_ctl flag to snd_hda_add_vmaster_hook()
ALSA: hda - Add "Mute-LED Mode" enum control
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"This contains the usual set of updates and bugfixes to target-core +
existing fabric module code, along with a handful of the patches
destined for v3.3 stable.
It also contains the necessary target-core infrastructure pieces
required to run using tcm_qla2xxx.ko WWPNs with the new Qlogic Fibre
Channel fabric module currently queued in target-pending/for-next-merge,
and coming for round 2.
The highlights for this series include:
- Add target_submit_tmr() helper function for fabric task management
(andy)
- Convert tcm_fc to use target_submit_tmr() (andy)
- Replace target core various cmd flags with a transport state (hch)
- Convert loopback to use workqueue submission (hch)
- Convert target core to use array_zalloc for tpg_lun_list (joern)
- Convert target core to use array_zalloc for device_list (joern)
- Add target core support for TMR_ABORT_TASK (nab)
- Add target core se_sess->sess_kref + get/put helpers (nab)
- Add target core se_node_acl->acl_kref for ->acl_free_comp usage
(nab)
- Convert iscsi-target to use target_put_session + sess_kref (nab)
- Fix tcm_fc fc_exch memory leak in ft_send_resp_status (nab)
- Fix ib_srpt srpt_handle_cmd send_ioctx->ioctx_kref leak on
exception (nab)
- Fix target core up handling of short INQUIRY buffers (roland)
- Untangle target-core front-end and back-end meanings of max_sectors
attribute (roland)
- Set loopback residual field for SCSI commands (roland)
- Fix target-core 16-bit target ports for SET TARGET PORT GROUPS
emulation (roland)
Thanks again to Andy, Christoph, Joern, Roland, and everyone who has
contributed this round!"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (64 commits)
ib_srpt: Fix srpt_handle_cmd send_ioctx->ioctx_kref leak on exception
loopback: Fix transport_generic_allocate_tasks error handling
iscsi-target: remove improper externs
iscsi-target: Remove unused variables in iscsi_target_parameters.c
target: remove obvious warnings
target: Use array_zalloc for device_list
target: Use array_zalloc for tpg_lun_list
target: Fix sense code for unsupported SERVICE ACTION IN
target: Remove hack to make READ CAPACITY(10) lie if thin provisioning is enabled
target: Bump core version to v4.1.0-rc2-ml + fabric versions
tcm_fc: Fix fc_exch memory leak in ft_send_resp_status
target: Drop unused legacy target_core_fabric_ops API callers
iscsi-target: Convert to use target_put_session + sess_kref
target: Convert se_node_acl->acl_group removal to use ->acl_kref
target: Add se_node_acl->acl_kref for ->acl_free_comp usage
target: Add se_node_acl->acl_free_comp for NodeACL release path
target: Add se_sess->sess_kref + get/put helpers
target: Convert session_lock to irqsave
target: Fix typo in drivers/target
iscsi-target: Fix dynamic -> explict NodeACL pointer reference
...
|
|
Pull md updates for 3.4 from Neil Brown:
"Mostly tidying up code in preparation for some bigger changes next
time.
A few bug fixes tagged for -stable.
Main functionality change is that some RAID10 arrays can now grow to
use extra space that may have been made available on the individual
devices."
Fixed up trivial conflicts with the k[un]map_atomic() cleanups in
drivers/md/bitmap.c.
* tag 'md-3.4' of git://neil.brown.name/md: (22 commits)
md: Add judgement bb->unacked_exist in function md_ack_all_badblocks().
md: fix clearing of the 'changed' flags for the bad blocks list.
md/bitmap: discard CHUNK_BLOCK_SHIFT macro
md/bitmap: remove unnecessary indirection when allocating.
md/bitmap: remove some pointless locking.
md/bitmap: change a 'goto' to a normal 'if' construct.
md/bitmap: move printing of bitmap status to bitmap.c
md/bitmap: remove some unused noise from bitmap.h
md/raid10 - support resizing some RAID10 arrays.
md/raid1: handle merge_bvec_fn in member devices.
md/raid10: handle merge_bvec_fn in member devices.
md: add proper merge_bvec handling to RAID0 and Linear.
md: tidy up rdev_for_each usage.
md/raid1,raid10: avoid deadlock during resync/recovery.
md/bitmap: ensure to load bitmap when creating via sysfs.
md: don't set md arrays to readonly on shutdown.
md: allow re-add to failed arrays.
md/raid5: use atomic_dec_return() instead of atomic_dec() and atomic_read().
md: Use existed macros instead of numbers
md/raid5: removed unused 'added_devices' variable.
...
|
|
|
|
amd_iommu_enable_interrupts() called in amd_iommu_resume().
Signed-off-by: Gerard Snitselaar <dev@snitselaar.org>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 platform changes from Ingo Molnar.
Removes the Moorestown platform that nobody ever used.
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform: Move APIC ID validity check into platform APIC code
x86/olpc/xo15/sci: Enable lid close wakeup control
x86/geode/net5501: Add platform driver for Soekris Engineering net5501
x86/geode/alix2: Supplement driver to include GPIO button support
x86/mid/powerbtn: Use MSIC read/write instead of ipc_scu
x86/mid/thermal: Turn off thermistor
x86/mid/thermal: Add msic_thermal alias
x86/mid/thermal: Convert to use Intel MSIC API
x86/mid/scu_ipc: Remove Moorestown support
x86/mid: Kill off Moorestown
x86/mrst: Add msic_thermal platform support
x86/config: Select MSIC MFD driver on Intel Medfield platform
x86/mid: Remove Intel Moorestown
x86/mrst: Set ISA bus type for fake MP IRQs
x86/ioapic: Use legacy_pic to set correct gsi-irq mapping
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MCE changes from Ingo Molnar.
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix return value of mce_chrdev_read() when erst is disabled
x86/mce: Convert static array of pointers to per-cpu variables
x86/mce: Replace hard coded hex constants with symbolic defines
x86/mce: Recognise machine check bank signature for data path error
x86/mce: Handle "action required" errors
x86/mce: Add mechanism to safely save information in MCE handler
x86/mce: Create helper function to save addr/misc when needed
HWPOISON: Add code to handle "action required" errors.
HWPOISON: Clean up memory_failure() vs. __memory_failure()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/debug changes from Ingo Molnar.
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix section warnings
x86-64: Fix CFI data for common_interrupt()
x86: Properly _init-annotate NMI selftest code
x86/debug: Fix/improve the show_msr=<cpus> debug print out
|
|
Merge first batch of patches from Andrew Morton:
"A few misc things and all the MM queue"
* emailed from Andrew Morton <akpm@linux-foundation.org>: (92 commits)
memcg: avoid THP split in task migration
thp: add HPAGE_PMD_* definitions for !CONFIG_TRANSPARENT_HUGEPAGE
memcg: clean up existing move charge code
mm/memcontrol.c: remove unnecessary 'break' in mem_cgroup_read()
mm/memcontrol.c: remove redundant BUG_ON() in mem_cgroup_usage_unregister_event()
mm/memcontrol.c: s/stealed/stolen/
memcg: fix performance of mem_cgroup_begin_update_page_stat()
memcg: remove PCG_FILE_MAPPED
memcg: use new logic for page stat accounting
memcg: remove PCG_MOVE_LOCK flag from page_cgroup
memcg: simplify move_account() check
memcg: remove EXPORT_SYMBOL(mem_cgroup_update_page_stat)
memcg: kill dead prev_priority stubs
memcg: remove PCG_CACHE page_cgroup flag
memcg: let css_get_next() rely upon rcu_read_lock()
cgroup: revert ss_id_lock to spinlock
idr: make idr_get_next() good for rcu_read_lock()
memcg: remove unnecessary thp check in page stat accounting
memcg: remove redundant returns
memcg: enum lru_list lru
...
|
|
git://git.freedesktop.org/git/nouveau/linux-2.6 into drm-next
* 'drm-nouveau-next' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/dp: support version 4.0 of DP table
drm/nve0/disp: nvidia randomly decided to move the dithering method
drm/nve0: initial modesetting support for kepler chipsets
drm/nouveau: add bios connector type for dms59
drm/nouveau: move out of staging drivers
drm/nouveau: bump version to 1.0.0
drm/nvd0/disp: ignore clock set if no pclk
drm/nouveau: oops, increase channel dispc_vma to 4
drm/nouveau: inform userspace of new kernel subchannel requirements
drm/nouveau: remove m2mf creation on userspace channels
drm/nvc0-/disp: reimplement flip completion method as fifo method
drm/nouveau: move fence sequence check to start of loop
drm/nouveau: remove subchannel names from places where it doesn't matter
drm/nouveau/ttm: always do buffer moves on kernel channel
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
