| Age | Commit message (Collapse) | Author |
|---|
|
When scanning, it is somewhat important to scan
on the correct virtual interface. All drivers
that currently implement hw_scan only support a
single virtual interface, but that may change
and then we'd want to be ready.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Now that the mac80211 is choosing dynamic ps timeouts based on the ps-qos
network latency configuration, configure a default value of -1 as the dynamic
ps timeout in cfg80211. This value allows the mac80211 to determine the value
to be used.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Determine the dynamic PS timeout based on the configured ps-qos network
latency. For backwards wext compatibility, allow the dynamic PS timeout
configured by the cfg80211 to overrule the automatically determined value.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is used to configure APs to not bridge traffic between connected stations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Our offset handling becomes even a little more hackish now. For some reason I
do not understand all offsets as inrelative. It assumes base offset is 0x1000
but it will work for now as we make offsets relative anyway by removing base
0x1000. Should be cleaner however.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Attempting to read registers that don't exist on the SSB bus can cause
hangs on some boxes. At least some b43 devices are 'in the wild' that
don't have SPROMs at all. When the SSB bus support loads, it attempts
to read these (non-existant) SPROMs and causes hard hangs on the box --
no console output, etc.
This patch adds some intelligence to determine whether or not the SPROM
is present before attempting to read it. This avoids those hard hangs
on those devices with no SPROM attached to their SSB bus. The
SSB-attached devices (e.g. b43, et al.) won't work, but at least the box
will survive to test further patches. :-)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>
|
|
When I updated this from the corresponding
userspace library, an annotation error crept
in -- this variable needs to be annotated as
little endian. No effect on code generation.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds the survey function to both mac80211 itself and to mac80211_hwsim.
For the latter driver, we simply invent some noise level.A real driver which
cannot determine the real channel noise MUST NOT report any noise, especially
not a magically conjured one :-)
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.
The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.
It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.
I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.
Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.
Signed-off-by: Daniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The flag is called IEEE80211_TX_STAT_AMPDU rather than using the whole word
STATUS.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
wl1251 has WLAN_IRQ pin for generating interrupts to host processor,
which is mandatory in SPI mode and optional in SDIO mode (which can
use SDIO interrupts instead). However TI recommends using deditated
IRQ line for SDIO too.
Add support for using dedicated interrupt line with SDIO, but also leave
ability to switch to SDIO interrupts in case it's needed.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
LDPC will be enabled through the rate control algorithm
for each buffer the the tx_info flags.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Grouped mesh action codes together with the other action codes in
ieee80211.h.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into merge
Conflicts:
Documentation/feature-removal-schedule.txt
drivers/net/wireless/ath/ath5k/phy.c
drivers/net/wireless/iwlwifi/iwl-4965.c
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/iwlwifi/iwl-core.h
drivers/net/wireless/iwlwifi/iwl-tx.c
|
|
The aggregation code has a number of quirks, like
inventing an unneeded WLAN_BACK_TIMER value and
leaking memory under certain circumstances during
station destruction. Fix these issues by using
the regular aggregation session teardown code and
blocking new aggregation sessions, all before the
station is really destructed.
As a side effect, this gets rid of the long code
block to destroy aggregation safely.
Additionally, rename tid_state_rx which can only
have the values IDLE and OPERATIONAL to
tid_active_rx to make it easier to understand
that there is no bitwise stuff going on on the
RX side -- the TX side remains because it needs
to keep track of the driver and peer states.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
cfg80211 is quite strict on allowing authentication and association
commands only in certain states. In order to meet these requirements,
user space applications may need to clear authentication or
association state in some cases. Currently, this can be done with
deauth/disassoc command, but that ends up sending out Deauthentication
or Disassociation frame unnecessarily. Add a new nl80211 attribute to
allow this sending of the frame be skipped, but with all other
deauth/disassoc operations being completed.
Similar state change is also needed for IEEE 802.11r FT protocol in
the FT-over-DS case which does not use Authentication frame exchange
in a transition to another BSS. For this to work with cfg80211, an
authentication entry needs to be created for the target BSS without
sending out an Authentication frame. The nl80211 authentication
command can be used for this purpose, too, with the new attribute to
indicate that the command is only for changing local state. This
enables wpa_supplicant to complete FT-over-DS transition successfully.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line.
However, the 8686 will only drive this line when the ECSI bit is set in
the CCCR_IF register.
Thanks to Alagu Sankar for pointing me in the right direction.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alagu Sankar <alagusankar@embwise.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
to match use in IW_IOCTL_IDX macro
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add interface to disable/enable QoS (aka WMM or WME). Currently drivers
enable it explicitly when ->conf_tx method is called, and newer disable.
Disabling is needed for some APs, which do not support QoS, such
we should send QoS frames to them.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Mac80211 drivers can now pass paged SKBs to mac80211 via
ieee80211_rx{_irqsafe}. The implementation currently use
skb_linearize() in a few places i.e. management frame
handling, software decryption, defragmentation and A-MSDU
process. We will optimize them one by one later.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Cc: Kalle Valo <kalle.valo@iki.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In nl80211.h, be a little more elaborate in the docs for the definitions
NL80211_ATTR_CQM_RSSI_THOLD and NL80211_ATTR_CQM_RSSI_HYST.
Reported-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add support for the set_cqm_config op. This op function configures the
requested connection quality monitor rssi threshold and rssi hysteresis
values to the hardware if the hardware supports
IEEE80211_HW_SUPPORTS_CQM.
For unsupported hardware, currently -EOPNOTSUPP is returned, so the mac80211
is currently not doing connection quality monitoring on the host. This could be
added later, if needed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add support for basic configuration of a connection quality monitoring to the
nl80211 interface, and basic support for notifying about triggered monitoring
events.
Via this interface a user-space connection manager may configure and receive
pre-warning events of deteriorating WLAN connection quality, and start
preparing for roaming in advance, before the connection is already lost.
An example usage of such a trigger is starting scanning for nearby AP's in
an attempt to find one with better connection quality, and associate to it
before the connection characteristics of the existing connection become too bad
or the association is even lost, leading in a prolonged delay in connectivity.
The interface currently supports only RSSI, but it could be later extended
to include other parameters, such as signal-to-noise ratio, if need for that
arises.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch is based on a RFC patch by Kalle Valo.
The wl1271 has a feature which handles the connection monitor logic
in hardware, basically sending periodically nullfunc frames and reporting
to the host if AP is lost, after attempting to recover by sending
probe-requests to the AP.
Add support to mac80211 by adding a new flag IEEE80211_HW_CONNECTION_MONITOR
which prevents conn_mon_timer from triggering during idle periods, and
prevents sending probe-requests to the AP if beacon-loss is indicated by the
hardware.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
These two #defines use the same value, but
SIOCIWFIRST makes more sense in this use.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Copied the idea from orinoco
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The noise value as is won't be used, isn't
filled by most drivers and doesn't really
make a whole lot of sense on a per packet
basis -- proper cfg80211 survey support in
mac80211 will need to be different.
Mark the struct member as deprecated so it
will be removed from drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit 6b03a53a (tcp: use limited socket backlog) added the possibility
of dropping frames when backlog queue is full.
Commit d218d111 (tcp: Generalized TTL Security Mechanism) added the
possibility of dropping frames when TTL is under a given limit.
This patch adds new SNMP MIB entries, named TCPBacklogDrop and
TCPMinTTLDrop, published in /proc/net/netstat in TcpExt: line
netstat -s | egrep "TCPBacklogDrop|TCPMinTTLDrop"
TCPBacklogDrop: 0
TCPMinTTLDrop: 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the "__must_check" tag to sk_add_backlog() so that any failure to
check and drop packets will be warned about.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPV6_PREFER_SRC_xxx definitions:
| #define IPV6_PREFER_SRC_TMP 0x0001
| #define IPV6_PREFER_SRC_PUBLIC 0x0002
| #define IPV6_PREFER_SRC_COA 0x0004
RT6_LOOKUP_F_xxx definitions:
| #define RT6_LOOKUP_F_SRCPREF_TMP 0x00000008
| #define RT6_LOOKUP_F_SRCPREF_PUBLIC 0x00000010
| #define RT6_LOOKUP_F_SRCPREF_COA 0x00000020
So, we can translate between these two groups by shift operation
instead of multiple 'if's.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 03/04/2010 09:26 AM, Ben Hutchings wrote:
> On Thu, 2010-03-04 at 00:51 -0800, Jeff Kirsher wrote:
>> From: Jeff Garzik<jgarzik@redhat.com>
>>
>> This patch is an alternative approach for accessing string
>> counts, vs. the drvinfo indirect approach. This way the drvinfo
>> space doesn't run out, and we don't break ABI later.
> [...]
>> --- a/net/core/ethtool.c
>> +++ b/net/core/ethtool.c
>> @@ -214,6 +214,10 @@ static noinline int ethtool_get_drvinfo(struct net_device *dev, void __user *use
>> info.cmd = ETHTOOL_GDRVINFO;
>> ops->get_drvinfo(dev,&info);
>>
>> + /*
>> + * this method of obtaining string set info is deprecated;
>> + * consider using ETHTOOL_GSSET_INFO instead
>> + */
>
> This comment belongs on the interface (ethtool.h) not the
> implementation.
Debatable -- the current comment is located at the callsite of
ops->get_sset_count(), which is where an implementor might think to add
a new call. Not all the numeric fields in ethtool_drvinfo are obtained
from ->get_sset_count().
Hence the "some" in the attached patch to include/linux/ethtool.h,
addressing your comment.
> [...]
>> +static noinline int ethtool_get_sset_info(struct net_device *dev,
>> + void __user *useraddr)
>> +{
> [...]
>> + /* calculate size of return buffer */
>> + for (i = 0; i< 64; i++)
>> + if (sset_mask& (1ULL<< i))
>> + n_bits++;
> [...]
>
> We have a function for this:
>
> n_bits = hweight64(sset_mask);
Agreed.
I've attached a follow-up patch, which should enable my/Jeff's kernel
patch to be applied, followed by this one.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is an alternative approach for accessing string
counts, vs. the drvinfo indirect approach. This way the drvinfo
space doesn't run out, and we don't break ABI later.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk_add_backlog -> __sk_add_backlog
sk_add_backlog_limited -> sk_add_backlog
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We got system OOM while running some UDP netperf testing on the loopback
device. The case is multiple senders sent stream UDP packets to a single
receiver via loopback on local host. Of course, the receiver is not able
to handle all the packets in time. But we surprisingly found that these
packets were not discarded due to the receiver's sk->sk_rcvbuf limit.
Instead, they are kept queuing to sk->sk_backlog and finally ate up all
the memory. We believe this is a secure hole that a none privileged user
can crash the system.
The root cause for this problem is, when the receiver is doing
__release_sock() (i.e. after userspace recv, kernel udp_recvmsg ->
skb_free_datagram_locked -> release_sock), it moves skbs from backlog to
sk_receive_queue with the softirq enabled. In the above case, multiple
busy senders will almost make it an endless loop. The skbs in the
backlog end up eat all the system memory.
The issue is not only for UDP. Any protocols using socket backlog is
potentially affected. The patch adds limit for socket backlog so that
the backlog size cannot be expanded endlessly.
Reported-by: Alex Shi <alex.shi@intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru
Cc: "Pekka Savola (ipv6)" <pekkas@netcore.fi>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Decreases the odds wakee will suffer from frequent cache misses.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When I merged the bundle creation code, I introduced a bogus
flowi value in the bundle. Instead of getting from the caller,
it was instead set to the flow in the route object, which is
totally different.
The end result is that the bundles we created never match, and
we instead end up with an ever growing bundle list.
Thanks to Jamal for find this problem.
Reported-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for handling KEY_RFKILL in the rfkill input module. This
simply toggles the state of all rfkill devices. The comment in rfkill.h
is also updated to reflect that RFKILL_TYPE_ALL may be used inside the
kernel.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux: (49 commits)
OMAP: DSS2: Taal: Fix TE when resuming
OMAP: DSS2: Taal: Fix ESD check
OMAP: DSS2: OMAPFB: Constify some function parameters
OMAP: DSS2: OMAPFB: install omapfb.h
OMAP: DSS2: DSI: add error prints
OMAP: DSS2: TPO-TD03MTEA1: fix function names
OMAP: DSS2: DSI: add dsi_vc_dcs_read_2() helper
OMAP: DSS2: OMAPFB: Remove FB_OMAP2_FORCE_AUTO_UPDATE
OMAP: DSS2: DSI: remove external TE support
OMAP: DSS2: move timing functions
OMAP: DSS2: move set/get_wss()
OMAP: DSS2: move enable/disable/suspend/resume
OMAP: DSS2: move update() and sync()
OMAP: DSS2: move set/get_update_mode()
OMAP: DSS2: move enable/get_te()
OMAP: DSS2: move get_recommended_bpp()
OMAP: DSS2: move get_resolution()
OMAP: DSS2: move enable/disable_channel to overlay manager
OMAP: DSS2: move wait_vsync()
OMAP: DSS2: move get/set_rotate()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (214 commits)
omap2: Initialize Menelaus and MMC for N8X0
AM3517 EVM: correct typo - tca6416 mispelt as tca6516
AM3517 EVM: Enable I2C support
AM35x: Enable OMAP_MUX in defconfig
AM35x: Add missing GPIO mux config for EHCI port
Zoom3: Defconfig update
omap: i2c: Fix muxing for command line enabled bus
OMAP4: clock: Remove clock hacks from timer-gp.c
OMAP4: clock: Add dummy clock nodes for interface clocks
OMAP4: clock: Rename leaf clock nodes to end with a _ick or _fck
OMAP2+ clock: revise omap2_clk_{disable,enable}()
OMAP2/3 clock: combine OMAP2 & 3 boot-time MPU rate change code
OMAP clockdomain: if no autodeps exist, don't try to add or remove them
OMAP hwmod: add hwmod class support
OMAP hwmod: convert header files with static allocations into C files
OMAP hwmod: convert hwmod to use hardware clock names rather than clkdev dev+con
OMAP clock: add omap_clk_get_by_name() for use by OMAP hwmod core code
OMAP3: clock: add capability to change rate of dpll4_m5_ck_3630
OMAP4 clock: drop the ALWAYS_ENABLED clock flag
OMAP clock: drop RATE_FIXED clock flag
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits)
virtio_net: remove forgotten assignment
be2net: fix tx completion polling
sis190: fix cable detect via link status poll
net: fix protocol sk_buff field
bridge: Fix build error when IGMP_SNOOPING is not enabled
bnx2x: Tx barriers and locks
scm: Only support SCM_RIGHTS on unix domain sockets.
vhost-net: restart tx poll on sk_sndbuf full
vhost: fix get_user_pages_fast error handling
vhost: initialize log eventfd context pointer
vhost: logging thinko fix
wireless: convert to use netdev_for_each_mc_addr
ethtool: do not set some flags, if others failed
ipoib: returned back addrlen check for mc addresses
netlink: Adding inode field to /proc/net/netlink
axnet_cs: add new id
bridge: Make IGMP snooping depend upon BRIDGE.
bridge: Add multicast count/interval sysfs entries
bridge: Add hash elasticity/max sysfs entries
bridge: Add multicast_snooping sysfs toggle
...
Trivial conflicts in Documentation/feature-removal-schedule.txt
|
|
Commit e992cd9b72a18 (kmemcheck: make bitfield annotations truly no-ops
when disabled) allows us to revert a workaround we did in the past to
not add holes in sk_buff structure.
This patch partially reverts commit 14d18a81b5171
(net: fix kmemcheck annotations) so that sparse doesnt complain:
include/linux/skbuff.h:357:41: error: invalid bitfield specifier for
type restricted __be16.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/arm/plat-omap/Kconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits)
DaVinci DM365: Adding support for SPI EEPROM
DaVinci DM365: Adding DM365 SPI support
DaVinci DM355: Modifications to DM355 SPI support
DaVinci: SPI: Adding header file for SPI support.
davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup
davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
DaVinci: DM365: Voice codec support for the DM365 SoC
davinci: clock: let clk->set_rate function sleep
Add SDA and SCL pin numbers to i2c platform data
davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138
davinci: build list of unused EDMA events dynamically
davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case
davinci: Keep count of channel controllers on a platform
davinci: Correct return value of edma_alloc_channel api
davinci: add CDCE949 support on DM6467 EVM
davinci: add support for CDCE949 clock synthesizer
davinci: da850/omap-l138 EVM: register for suspend support
davinci: da850/omap-l138: add support for SoC suspend
davinci: add power management support
DaVinci: DM365: Changing default queue for DM365.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits)
sata_via: Delay on vt6420 when starting ATAPI DMA write
ata: Detect Delkin Devices compact flash
pata_efar: Enable parallel scanning
pata_atiixp: enable parallel scan
[libata] pata_atiixp: add locking for parallel scanning
[libata] pata_efar: add locking for parallel scanning
libata: Pass host flags into the pci helper
[libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI
libata: Allow pata_legacy to be built on non-ISA but PCI systems
pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets
pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards
[libata] pata_at91: fix backslash-continued string
pata_via: store UDMA masks in via_isa_bridges table
pata_via: fix address setup timings underlocking
pata_serverworks: fix error message
pata_serverworks: fix PIO setup for the second channel
pata_efar: fix secondary port support
pata_cypress: fix PIO timings underclocking
pata_cs5535: use correct values for PIO1 and PIO2 data timings
pata_cmd64x: remove unused definitions
...
|
