summaryrefslogtreecommitdiff
path: root/net
AgeCommit message (Collapse)Author
2008-12-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits) net: Allow dependancies of FDDI & Tokenring to be modular. igb: Fix build warning when DCA is disabled. net: Fix warning fallout from recent NAPI interface changes. gro: Fix potential use after free sfc: If AN is enabled, always read speed/duplex from the AN advertising bits sfc: When disabling the NIC, close the device rather than unregistering it sfc: SFT9001: Add cable diagnostics sfc: Add support for multiple PHY self-tests sfc: Merge top-level functions for self-tests sfc: Clean up PHY mode management in loopback self-test sfc: Fix unreliable link detection in some loopback modes sfc: Generate unique names for per-NIC workqueues 802.3ad: use standard ethhdr instead of ad_header 802.3ad: generalize out mac address initializer 802.3ad: initialize ports LACPDU from const initializer 802.3ad: remove typedef around ad_system 802.3ad: turn ports is_individual into a bool 802.3ad: turn ports is_enabled into a bool 802.3ad: make ntt bool ixgbe: Fix set_ringparam in ixgbe to use the same memory pools. ... Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due to the conversion to %pI (in this networking merge) and the addition of doing IPv6 addresses (from the earlier merge of CIFS).
2008-12-28Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6Linus Torvalds
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (85 commits) [S390] provide documentation for hvc_iucv kernel parameter. [S390] convert ctcm printks to dev_xxx and pr_xxx macros. [S390] convert zfcp printks to pr_xxx macros. [S390] convert vmlogrdr printks to pr_xxx macros. [S390] convert zfcp dumper printks to pr_xxx macros. [S390] convert cpu related printks to pr_xxx macros. [S390] convert qeth printks to dev_xxx and pr_xxx macros. [S390] convert sclp printks to pr_xxx macros. [S390] convert iucv printks to dev_xxx and pr_xxx macros. [S390] convert ap_bus printks to pr_xxx macros. [S390] convert dcssblk and extmem printks messages to pr_xxx macros. [S390] convert monwriter printks to pr_xxx macros. [S390] convert s390 debug feature printks to pr_xxx macros. [S390] convert monreader printks to pr_xxx macros. [S390] convert appldata printks to pr_xxx macros. [S390] convert setup printks to pr_xxx macros. [S390] convert hypfs printks to pr_xxx macros. [S390] convert time printks to pr_xxx macros. [S390] convert cpacf printks to pr_xxx macros. [S390] convert cio printks to pr_xxx macros. ...
2008-12-26gro: Fix potential use after freeHerbert Xu
The initial skb may have been freed after napi_gro_complete in napi_gro_receive if it was merged into an existing packet. Thus we cannot check same_flow (which indicates whether it was merged) after calling napi_gro_complete. This patch fixes this by saving the same_flow status before the call to napi_gro_complete. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26net: Init NAPI dev_list on napi_delPeter P Waskiewicz Jr
The recent GRO patches introduced the NAPI removal of devices in free_netdev. For drivers that can change the number of queues during driver operation, the NAPI infrastructure doesn't allow the freeing and re-addition of NAPI entities without reloading the driver. This change reinitializes the dev_list in each NAPI struct on delete, instead of just deleting it (and assigning the list pointers to POISON). Drivers that wish to remove/re-add NAPI will need to re-initialize the netdev napi_list after removing all NAPI instances, before re-adding NAPI devices again. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26ipsec: Remove useless ret variableHerbert Xu
This patch removes a useless ret variable from the IPv4 ESP/UDP decapsulation code. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25net/appletalk: Remove redundant testJulia Lawall
atif is tested for being NULL twice, with the same effect in each case. I have kept the second test, as it seems to fit well with the comment above it. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; expression E; position p1,p2; @@ if (x@p1 == NULL || ...) { ... when forall return ...; } ... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\) ( x@p2 == NULL | x@p2 != NULL ) // another path to the test that is not through p1? @s exists@ local idexpression r.x; position r.p1,r.p2; @@ ... when != x@p1 ( x@p2 == NULL | x@p2 != NULL ) @fix depends on !s@ position r.p1,r.p2; expression x,E; statement S1,S2; @@ ( - if ((x@p2 != NULL) || ...) S1 | - if ((x@p2 == NULL) && ...) S1 | - BUG_ON(x@p2 == NULL); ) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25tcp: Always set urgent pointer if it's beyond snd_nxtHerbert Xu
Our TCP stack does not set the urgent flag if the urgent pointer does not fit in 16 bits, i.e., if it is more than 64K from the sequence number of a packet. This behaviour is different from the BSDs, and clearly contradicts the purpose of urgent mode, which is to send the notification (though not necessarily the associated data) as soon as possible. Our current behaviour may in fact delay the urgent notification indefinitely if the receiver window does not open up. Simply matching BSD however may break legacy applications which incorrectly rely on the out-of-band delivery of urgent data, and conversely the in-band delivery of non-urgent data. Alexey Kuznetsov suggested a safe solution of following BSD only if the urgent pointer itself has not yet been transmitted. This way we guarantee that when the remote end sees the packet with non-urgent data marked as urgent due to wrap-around we would have advanced the urgent pointer beyond, either to the actual urgent data or to an as-yet untransmitted packet. The only potential downside is that applications on the remote end may see multiple SIGURG notifications. However, this would occur anyway with other TCP stacks. More importantly, the outcome of such a duplicate notification is likely to be harmless since the signal itself does not carry any information other than the fact that we're in urgent mode. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25sctp: Add validity check for SCTP_PARTIAL_DELIVERY_POINT socket optionWei Yongjun
The latest ietf socket extensions API draft said: 8.1.21. Set or Get the SCTP Partial Delivery Point Note also that the call will fail if the user attempts to set this value larger than the socket receive buffer size. This patch add this validity check for SCTP_PARTIAL_DELIVERY_POINT socket option. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25sctp: Avoid memory overflow while FWD-TSN chunk is received with bad stream IDWei Yongjun
If FWD-TSN chunk is received with bad stream ID, the sctp will not do the validity check, this may cause memory overflow when overwrite the TSN of the stream ID. The FORWARD-TSN chunk is like this: FORWARD-TSN chunk Type = 192 Flags = 0 Length = 172 NewTSN = 99 Stream = 10000 StreamSequence = 0xFFFF This patch fix this problem by discard the chunk if stream ID is not less than MIS. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25sctp: Implement socket option SCTP_GET_ASSOC_NUMBERWei Yongjun
Implement socket option SCTP_GET_ASSOC_NUMBER of the latest ietf socket extensions API draft. 8.2.5. Get the Current Number of Associations (SCTP_GET_ASSOC_NUMBER) This option gets the current number of associations that are attached to a one-to-many style socket. The option value is an uint32_t. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25sctp: Fix a typo in socket.cWei Yongjun
Just fix a typo in socket.c. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25sctp: Bring SCTP_MAXSEG socket option into ietf API extension complianceWei Yongjun
Brings maxseg socket option set/get into line with the latest ietf socket extensions API draft, while maintaining backwards compatibility. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25vlan: fix convertion to net_device_opsEric Dumazet
commit 656299f706e52e0409733d704c2761f1b12d6954 (vlan: convert to net_device_ops) added a net_device_ops with a NULL ndo_start_xmit field. This gives a crash in dev_hard_start_xmit() Fix it using two net_device_ops structures, one for hwaccel vlan, one for non hwaccel vlan. Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25netns: igmp: make /proc/net/{igmp,mcfilter} per netnsAlexey Dobriyan
This patch makes the followinf proc entries per-netns: /proc/net/igmp /proc/net/mcfilter Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com> Acked-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25netns: igmp: allow IPPROTO_IGMP sockets in netnsAlexey Dobriyan
Looks like everything is already ready. Required for ebtables(8) for one thing. Also, required for ipmr per-netns (coming soon). (Benjamin) Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Acked-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25[S390] convert iucv printks to dev_xxx and pr_xxx macros.Ursula Braun
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25[S390] iucv: Locking free version of iucv_message_(receive|send)Hendrik Brueckner
Provide a locking free version of iucv_message_receive and iucv_message_send that do not call local_bh_enable in a spin_lock_(bh|irqsave)() context. Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
2008-12-25Merge branch 'next' into for-linusJames Morris
2008-12-23Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/ppp_generic.c
2008-12-22pkt_sched: Remove smp_wmb() in qdisc_watchdog()Jarek Poplawski
While implementing a TCQ_F_THROTTLED flag there was used an smp_wmb() in qdisc_watchdog(), but since this flag is practically used only in sch_netem(), and since it's not even clear what reordering is avoided here (TCQ_F_THROTTLED vs. __QDISC_STATE_SCHED?) it seems the barrier could be safely removed. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-22net: Fix oops in dev_ifsioc()Jarek Poplawski
A command like this: "brctl addif br1 eth1" issued as a user gave me an oops when bridge module wasn't loaded. It's caused by using a dev pointer before checking for NULL. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-21pkt_sched: Annotate uninitialized var in sfq_enqueue()Jarek Poplawski
Some gcc versions warn that ret may be used uninitialized in sfq_enqueue(). It's a false positive, so let's annotate this. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-21net: add DCNA attribute to the BCN interface for DCBDon Skidmore
Adds the Backward Congestion Notification Address (BCNA) attribute to the Backward Congestion Notification (BCN) interface for Data Center Bridging (DCB), which was missing. Receive the BCNA attribute in the ixgbe driver. The BCNA attribute is for a switch to inform the endstation about the physical port identification in order to support BCN on aggregated links. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2008-12-21net: fix DCB setstate to return success/failureDon Skidmore
Data Center Bridging (DCB) had no way to know if setstate had failed in the driver. This patch enables dcb netlink code to handle the status for the DCB setstate interface. Likewise it allows the driver to return a failed status if MSI-X isn't enabled. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-19mac80211: implement dynamic power saveKalle Valo
This patch implements dynamic power save for mac80211. Basically it means enabling power save mode after an idle period. Implementing it dynamically gives a good compromise of low power consumption and low latency. Some hardware have support for this in firmware, but some require the host to do it. The dynamic power save is implemented by adding an timeout to ieee80211_subif_start_xmit(). The timeout can be enabled from userspace with Wireless Extensions. For example, the command below enables the dynamic power save and sets the time timeout to 500 ms: iwconfig wlan0 power timeout 500m Power save now only works with devices which handle power save in firmware. It's also disabled by default and the heuristics when and how to enable is considered as a policy decision and will be left for the userspace to handle. In case the firmware has support for this, drivers can disable this feature with IEEE80211_HW_NO_STACK_DYNAMIC_PS. Big thanks to Johannes Berg for the help with the design and code. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19mac80211: track master queue statusKalle Valo
This is a preparation for the dynamic power save support. In future there are two paths to stop the master queues and we need to track this properly to avoid starting queues incorrectly. Implement this by adding a status array for each queue. The original idea and design is from Johannes Berg, I just did the implementation based on his notes. All the bugs are mine, of course. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19mac80211: enable IEEE80211_CONF_PS only when associatedKalle Valo
Also disable power save when disassociated. It makes no sense to have power save enabled while disassociated. iwlwifi seems to have this check in the driver, but it's better to do this in mac80211 instead. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19mac80211: Print unknown packet type in tasklet_handlerLarry Finger
In stress testing p54usb, the WARN_ON() in ieee80211_tasklet_handler() was triggered; however, there is no logging of the received value for packet type. Adding that feature will improve the warning. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19mac80211: fix a typo in ieee80211_send_assoc() method.Rami Rosen
This patch fixes a typo in ieee80211_send_assoc(), net/mac80211/mlme.c. The error is usage of a wrong member when building the ie80211 management frame (it should be assoc_req, and not reassoc_req). Signed-off-by: Rami Rosen <ramirose@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19mac80211: Remove radiotap rate-present flag for HTJouni Malinen
Since we do not currently report HT rates (MCS index) in radiotap header for HT rates, we should not claim the rate is present. The rate octet itself is used as padding in this case, so only the it_present flag needs to be removed in case of HT rates. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19mac80211: Send Layer 2 Update frame on reassociationJouni Malinen
When a STA roams back to the same AP before the previous STA entry has expired, a new STA entry is not added in mac80211. However, a Layer 2 Update frame still needs to be transmitted to update layer 2 devices about the new location for the STA. Without this, switches may continue to forward frames to the previous (now incorrect) port when STA roams between APs. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19mac80211: Add HT rates into RX status reportingJouni Malinen
This patch adds option for HT-enabled drivers to report HT rates (HT20/HT40, short GI, MCS index) to mac80211. These rates are currently not in the rate table, so the rate_idx is used to indicate MCS index. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19mac80211: Fix HT channel selectionSujith
HT management is done differently for AP and STA modes, unify to just the ->config() callback since HT is fundamentally a PHY property and cannot be per-BSS. Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote the channel type ( NO_HT, HT20, HT40+, HT40- ). Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19nl80211: Add signal strength and bandwith to nl80211station infoHenning Rogge
This patch adds signal strength and transmission bitrate to the station_info of nl80211. Signed-off-by: Henning Rogge <rogge@fgan.de> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-18tcp: Stop scaring users with "treason uncloaked!"Matt Mackall
The original message was unhelpful and extremely alarming to our poor users, despite its charm. Make it less frightening. Signed-off-by: Matt Mackall <mpm@selenic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18Revert "xfrm: Accept ESP packets regardless of UDP encapsulation mode"David S. Miller
This reverts commit e061b165c7f4ec5e2e160d990b49011b5b6e5c6a. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18net: Fix module refcount leak in kernel_accept()Wei Yongjun
The kernel_accept() does not hold the module refcount of newsock->ops->owner, so we need __module_get(newsock->ops->owner) code after call kernel_accept() by hand. In sunrpc, the module refcount is missing to hold. So this cause kernel panic. Used following script to reproduct: while [ 1 ]; do mount -t nfs4 192.168.0.19:/ /mnt touch /mnt/file umount /mnt lsmod | grep ipv6 done This patch fixed the problem by add __module_get(newsock->ops->owner) to kernel_accept(). So we do not need to used __module_get(newsock->ops->owner) in every place when used kernel_accept(). Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17Revert "net: release skb->dst in sock_queue_rcv_skb()"David S. Miller
This reverts commit 70355602879229c6f8bd694ec9c0814222bc4936. As pointed out by Mark McLoughlin IP_PKTINFO cmsg data is one post-queueing user, so this optimization is not valid right now. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17dccp_diag: LISTEN sockets don't have CCIDsArnaldo Carvalho de Melo
And thus when we try to use 'ss -danemi' on these sockets that have no ccid blocks (data collected using systemtap after I fixed the problem): dccp_diag_get_info sk=0xffff8801220a3100, dp->dccps_hc_rx_ccid=0x0000000000000000, dp->dccps_hc_tx_ccid=0x0000000000000000 We get an OOPS: mica.ghostprotocols.net login: BUG: unable to handle kernel NULL pointer dereferenc0 IP: [<ffffffffa0136082>] dccp_diag_get_info+0x82/0xc0 [dccp_diag] PGD 12106f067 PUD 122488067 PMD 0 Oops: 0000 [#1] PREEMPT Fix is trivial, and 'ss -d' is working again: [root@mica ~]# ss -danemi State Recv-Q Send-Q Local Address:Port Peer Address:Port LISTEN 0 0 *:5001 *:* ino:7288 sk:220a3100ffff8801 mem:(r0,w0,f0,t0) cwnd:0 ssthresh:0 [root@mica ~]# Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17Phonet: get rid of deferred work on the transmission pathRémi Denis-Courmont
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17Phonet: use atomic for packet TX windowRémi Denis-Courmont
GPRS TX flow control won't need to lock the underlying socket anymore. Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17Phonet: allocate separate ARP type for GPRS over a Phonet pipeRémi Denis-Courmont
A separate xmit lock class supports GPRS over a Phonet pipe over a TUN device (type ARPHRD_NONE). Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17Phonet: allocate a non-Ethernet ARP typeRémi Denis-Courmont
Also leave some room for more 802.11 types. Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-16ipv6: fix the outgoing interface selection order in udpv6_sendmsg()Yang Hongyang
1.When no interface is specified in an IPV6_PKTINFO ancillary data item, the interface specified in an IPV6_PKTINFO sticky optionis is used. RFC3542: 6.7. Summary of Outgoing Interface Selection This document and [RFC-3493] specify various methods that affect the selection of the packet's outgoing interface. This subsection summarizes the ordering among those in order to ensure deterministic behavior. For a given outgoing packet on a given socket, the outgoing interface is determined in the following order: 1. if an interface is specified in an IPV6_PKTINFO ancillary data item, the interface is used. 2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky option, the interface is used. Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-16ipv6: fix the return interface index when get it while no message is receivedYang Hongyang
When get receiving interface index while no message is received, the the value seted with setsockopt() should be returned. RFC 3542: Issuing getsockopt() for the above options will return the sticky option value i.e., the value set with setsockopt(). If no sticky option value has been set getsockopt() will return the following values: - For the IPV6_PKTINFO option, it will return an in6_pktinfo structure with ipi6_addr being in6addr_any and ipi6_ifindex being zero. Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-16ipv6: Add IPV6_PKTINFO sticky option support to setsockopt()Yang Hongyang
There are three reasons for me to add this support: 1.When no interface is specified in an IPV6_PKTINFO ancillary data item, the interface specified in an IPV6_PKTINFO sticky optionis is used. RFC3542: 6.7. Summary of Outgoing Interface Selection This document and [RFC-3493] specify various methods that affect the selection of the packet's outgoing interface. This subsection summarizes the ordering among those in order to ensure deterministic behavior. For a given outgoing packet on a given socket, the outgoing interface is determined in the following order: 1. if an interface is specified in an IPV6_PKTINFO ancillary data item, the interface is used. 2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky option, the interface is used. 2.When no IPV6_PKTINFO ancillary data is received,getsockopt() should return the sticky option value which set with setsockopt(). RFC 3542: Issuing getsockopt() for the above options will return the sticky option value i.e., the value set with setsockopt(). If no sticky option value has been set getsockopt() will return the following values: 3.Make the setsockopt implementation POSIX compliant. Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-16Phonet: improve GPRS variable namesRémi Denis-Courmont
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-16ipmr: merge common codeIlpo Järvinen
Also removes redundant skb->len < x check which can't be true once pskb_may_pull(skb, x) succeeded. $ diff-funcs pim_rcv ipmr.c ipmr.c pim_rcv_v1 --- ipmr.c:pim_rcv() +++ ipmr.c:pim_rcv_v1() @@ -1,22 +1,27 @@ -static int pim_rcv(struct sk_buff * skb) +int pim_rcv_v1(struct sk_buff * skb) { - struct pimreghdr *pim; + struct igmphdr *pim; struct iphdr *encap; struct net_device *reg_dev = NULL; if (!pskb_may_pull(skb, sizeof(*pim) + sizeof(*encap))) goto drop; - pim = (struct pimreghdr *)skb_transport_header(skb); - if (pim->type != ((PIM_VERSION<<4)|(PIM_REGISTER)) || - (pim->flags&PIM_NULL_REGISTER) || - (ip_compute_csum((void *)pim, sizeof(*pim)) != 0 && - csum_fold(skb_checksum(skb, 0, skb->len, 0)))) + pim = igmp_hdr(skb); + + if (!mroute_do_pim || + skb->len < sizeof(*pim) + sizeof(*encap) || + pim->group != PIM_V1_VERSION || pim->code != PIM_V1_REGISTER) goto drop; - /* check if the inner packet is destined to mcast group */ encap = (struct iphdr *)(skb_transport_header(skb) + - sizeof(struct pimreghdr)); + sizeof(struct igmphdr)); + /* + Check that: + a. packet is really destinted to a multicast group + b. packet is not a NULL-REGISTER + c. packet is not truncated + */ if (!ipv4_is_multicast(encap->daddr) || encap->tot_len == 0 || ntohs(encap->tot_len) + sizeof(*pim) > skb->len) @@ -40,9 +45,9 @@ skb->ip_summed = 0; skb->pkt_type = PACKET_HOST; dst_release(skb->dst); + skb->dst = NULL; reg_dev->stats.rx_bytes += skb->len; reg_dev->stats.rx_packets++; - skb->dst = NULL; nf_reset(skb); netif_rx(skb); dev_put(reg_dev); $ codiff net/ipv4/ipmr.o.old net/ipv4/ipmr.o.new net/ipv4/ipmr.c: pim_rcv_v1 | -283 pim_rcv | -284 2 functions changed, 567 bytes removed net/ipv4/ipmr.c: __pim_rcv | +307 1 function changed, 307 bytes added net/ipv4/ipmr.o.new: 3 functions changed, 307 bytes added, 567 bytes removed, diff: -260 (Tested on x86_64). It seems that pimlen arg could be left out as well and eq-sizedness of structs trapped with BUILD_BUG_ON but I don't think that's more than a cosmetic flaw since there aren't that many args anyway. Compile tested. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-15ethtool: Add GGRO and SGRO opsHerbert Xu
This patch adds the ethtool ops to enable and disable GRO. It also makes GRO depend on RX checksum offload much the same as how TSO depends on SG support. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-15tcp: Add GRO supportHerbert Xu
This patch adds the TCP-specific portion of GRO. The criterion for merging is extremely strict (the TCP header must match exactly apart from the checksum) so as to allow refragmentation. Otherwise this is pretty much identical to LRO, except that we support the merging of ECN packets. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>