From 01f3880dd8a7fa78c419da2db740cba511ca7798 Mon Sep 17 00:00:00 2001 From: Michael Ellerman Date: Wed, 16 Jul 2008 14:21:34 +1000 Subject: powerpc: Streamline ret_from_except_lite for non-iSeries platforms There is a small passage of code in ret_from_except_lite which is only required on iSeries. For a multi-platform kernel on non-iSeries machines this means we end up executing ~15 nops in ret_from_except_lite. It would be nicer if non-iSeries could skip the code entirely, and on iSeries we can jump out of line to execute the code. I have no performance numbers to justify this, other than the assertion that executing 15 nops takes longer than executing 0. Signed-off-by: Michael Ellerman Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/entry_64.S | 53 +++++++++++++++++++++++------------------- 1 file changed, 29 insertions(+), 24 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S index 2d802e97097..55445f1dba8 100644 --- a/arch/powerpc/kernel/entry_64.S +++ b/arch/powerpc/kernel/entry_64.S @@ -512,31 +512,12 @@ _GLOBAL(ret_from_except_lite) #endif restore: - ld r5,SOFTE(r1) -#ifdef CONFIG_PPC_ISERIES BEGIN_FW_FTR_SECTION - cmpdi 0,r5,0 - beq 4f - /* Check for pending interrupts (iSeries) */ - ld r3,PACALPPACAPTR(r13) - ld r3,LPPACAANYINT(r3) - cmpdi r3,0 - beq+ 4f /* skip do_IRQ if no interrupts */ - - li r3,0 - stb r3,PACASOFTIRQEN(r13) /* ensure we are soft-disabled */ -#ifdef CONFIG_TRACE_IRQFLAGS - bl .trace_hardirqs_off - mfmsr r10 -#endif - ori r10,r10,MSR_EE - mtmsrd r10 /* hard-enable again */ - addi r3,r1,STACK_FRAME_OVERHEAD - bl .do_IRQ - b .ret_from_except_lite /* loop back and handle more */ -4: -END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) -#endif + ld r5,SOFTE(r1) +FW_FTR_SECTION_ELSE + b iseries_check_pending_irqs +ALT_FW_FTR_SECTION_END_IFCLR(FW_FEATURE_ISERIES) +2: TRACE_AND_RESTORE_IRQ(r5); /* extract EE bit and use it to restore paca->hard_enabled */ @@ -592,6 +573,30 @@ END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) rfid b . /* prevent speculative execution */ +iseries_check_pending_irqs: +#ifdef CONFIG_PPC_ISERIES + ld r5,SOFTE(r1) + cmpdi 0,r5,0 + beq 2b + /* Check for pending interrupts (iSeries) */ + ld r3,PACALPPACAPTR(r13) + ld r3,LPPACAANYINT(r3) + cmpdi r3,0 + beq+ 2b /* skip do_IRQ if no interrupts */ + + li r3,0 + stb r3,PACASOFTIRQEN(r13) /* ensure we are soft-disabled */ +#ifdef CONFIG_TRACE_IRQFLAGS + bl .trace_hardirqs_off + mfmsr r10 +#endif + ori r10,r10,MSR_EE + mtmsrd r10 /* hard-enable again */ + addi r3,r1,STACK_FRAME_OVERHEAD + bl .do_IRQ + b .ret_from_except_lite /* loop back and handle more */ +#endif + do_work: #ifdef CONFIG_PREEMPT andi. r0,r3,MSR_PR /* Returning to user mode? */ -- cgit v1.2.3 From 542ad5d4ccbaf49f581bacff1af206077189bc30 Mon Sep 17 00:00:00 2001 From: Harvey Harrison Date: Thu, 31 Jul 2008 05:29:03 +1000 Subject: powerpc: Use the common ascii hex helpers [akpm@linux-foundation.org: exclude prom_init.c] Signed-off-by: Harvey Harrison Signed-off-by: Andrew Morton Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/btext.c | 34 ++++++++++++++++------------------ 1 file changed, 16 insertions(+), 18 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/btext.c b/arch/powerpc/kernel/btext.c index d8f0329b134..26e58630ed7 100644 --- a/arch/powerpc/kernel/btext.c +++ b/arch/powerpc/kernel/btext.c @@ -442,28 +442,26 @@ void btext_drawtext(const char *c, unsigned int len) void btext_drawhex(unsigned long v) { - char *hex_table = "0123456789abcdef"; - if (!boot_text_mapped) return; #ifdef CONFIG_PPC64 - btext_drawchar(hex_table[(v >> 60) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 56) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 52) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 48) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 44) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 40) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 36) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 32) & 0x0000000FUL]); + btext_drawchar(hex_asc_hi(v >> 56)); + btext_drawchar(hex_asc_lo(v >> 56)); + btext_drawchar(hex_asc_hi(v >> 48)); + btext_drawchar(hex_asc_lo(v >> 48)); + btext_drawchar(hex_asc_hi(v >> 40)); + btext_drawchar(hex_asc_lo(v >> 40)); + btext_drawchar(hex_asc_hi(v >> 32)); + btext_drawchar(hex_asc_lo(v >> 32)); #endif - btext_drawchar(hex_table[(v >> 28) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 24) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 20) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 16) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 12) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 8) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 4) & 0x0000000FUL]); - btext_drawchar(hex_table[(v >> 0) & 0x0000000FUL]); + btext_drawchar(hex_asc_hi(v >> 24)); + btext_drawchar(hex_asc_lo(v >> 24)); + btext_drawchar(hex_asc_hi(v >> 16)); + btext_drawchar(hex_asc_lo(v >> 16)); + btext_drawchar(hex_asc_hi(v >> 8)); + btext_drawchar(hex_asc_lo(v >> 8)); + btext_drawchar(hex_asc_hi(v)); + btext_drawchar(hex_asc_lo(v)); btext_drawchar(' '); } -- cgit v1.2.3 From 5df72bf3f7345a84f5ef274bf72a4546caf3ad02 Mon Sep 17 00:00:00 2001 From: Harvey Harrison Date: Thu, 31 Jul 2008 05:29:03 +1000 Subject: powerpc: Replace __FUNCTION__ with __func__ __FUNCTION__ is gcc-specific, use __func__ [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Harvey Harrison Cc: Benjamin Herrenschmidt Signed-off-by: Andrew Morton Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/lparcfg.c | 8 ++++---- arch/powerpc/platforms/pseries/cmm.c | 4 ++-- 2 files changed, 6 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/lparcfg.c b/arch/powerpc/kernel/lparcfg.c index b3eef30b513..d051e8cbcd0 100644 --- a/arch/powerpc/kernel/lparcfg.c +++ b/arch/powerpc/kernel/lparcfg.c @@ -510,10 +510,10 @@ static ssize_t update_ppp(u64 *entitlement, u8 *weight) return -EINVAL; pr_debug("%s: current_entitled = %lu, current_weight = %u\n", - __FUNCTION__, ppp_data.entitlement, ppp_data.weight); + __func__, ppp_data.entitlement, ppp_data.weight); pr_debug("%s: new_entitled = %lu, new_weight = %u\n", - __FUNCTION__, new_entitled, new_weight); + __func__, new_entitled, new_weight); retval = plpar_hcall_norets(H_SET_PPP, new_entitled, new_weight); return retval; @@ -556,10 +556,10 @@ static ssize_t update_mpp(u64 *entitlement, u8 *weight) return -EINVAL; pr_debug("%s: current_entitled = %lu, current_weight = %u\n", - __FUNCTION__, mpp_data.entitled_mem, mpp_data.mem_weight); + __func__, mpp_data.entitled_mem, mpp_data.mem_weight); pr_debug("%s: new_entitled = %lu, new_weight = %u\n", - __FUNCTION__, new_entitled, new_weight); + __func__, new_entitled, new_weight); rc = plpar_hcall_norets(H_SET_MPP, new_entitled, new_weight); return rc; diff --git a/arch/powerpc/platforms/pseries/cmm.c b/arch/powerpc/platforms/pseries/cmm.c index 38fe32a7cc7..5cd4d276162 100644 --- a/arch/powerpc/platforms/pseries/cmm.c +++ b/arch/powerpc/platforms/pseries/cmm.c @@ -121,7 +121,7 @@ static long cmm_alloc_pages(long nr) npa = (struct cmm_page_array *)__get_free_page(GFP_NOIO | __GFP_NOWARN | __GFP_NORETRY | __GFP_NOMEMALLOC); if (!npa) { - pr_info("%s: Can not allocate new page list\n", __FUNCTION__); + pr_info("%s: Can not allocate new page list\n", __func__); free_page(addr); break; } @@ -138,7 +138,7 @@ static long cmm_alloc_pages(long nr) } if ((rc = plpar_page_set_loaned(__pa(addr)))) { - pr_err("%s: Can not set page to loaned. rc=%ld\n", __FUNCTION__, rc); + pr_err("%s: Can not set page to loaned. rc=%ld\n", __func__, rc); spin_unlock(&cmm_lock); free_page(addr); break; -- cgit v1.2.3 From e16a9c0990a18ee2f2874363392fdfedcf9ded58 Mon Sep 17 00:00:00 2001 From: Tony Breeds Date: Thu, 31 Jul 2008 13:51:42 +1000 Subject: powerpc: Guard htab_dt_scan_hugepage_blocks appropriately htab_dt_scan_hugepage_blocks is only used when CONFIG_HUGETLB_PAGE is defined, so guard the declaration likewise. Signed-off-by: Tony Breeds Signed-off-by: Paul Mackerras --- arch/powerpc/mm/hash_utils_64.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/mm/hash_utils_64.c b/arch/powerpc/mm/hash_utils_64.c index 14be408dfc9..7efcb9c5217 100644 --- a/arch/powerpc/mm/hash_utils_64.c +++ b/arch/powerpc/mm/hash_utils_64.c @@ -343,6 +343,7 @@ static int __init htab_dt_scan_page_sizes(unsigned long node, return 0; } +#ifdef CONFIG_HUGETLB_PAGE /* Scan for 16G memory blocks that have been set aside for huge pages * and reserve those blocks for 16G huge pages. */ @@ -380,6 +381,7 @@ static int __init htab_dt_scan_hugepage_blocks(unsigned long node, add_gpage(phys_addr, block_size, expected_pages); return 0; } +#endif /* CONFIG_HUGETLB_PAGE */ static void __init htab_init_page_sizes(void) { -- cgit v1.2.3 From fedcf4c73e1b9c1c594cf12d946ea90b7a47cc08 Mon Sep 17 00:00:00 2001 From: Tony Breeds Date: Thu, 31 Jul 2008 13:51:43 +1000 Subject: powerpc: Guard from_rtc_time() in platforms/powermac/time.c from_rtc_time() is only called when one of 3 CONFIG options are defined. Guard the declaration appropriately. Signed-off-by: Tony Breeds Signed-off-by: Paul Mackerras --- arch/powerpc/platforms/powermac/time.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/platforms/powermac/time.c b/arch/powerpc/platforms/powermac/time.c index bbbefd64ab5..59eb840d8ce 100644 --- a/arch/powerpc/platforms/powermac/time.c +++ b/arch/powerpc/platforms/powermac/time.c @@ -93,11 +93,14 @@ static void to_rtc_time(unsigned long now, struct rtc_time *tm) } #endif +#if defined(CONFIG_ADB_CUDA) || defined(CONFIG_ADB_PMU) || \ + defined(CONFIG_PMAC_SMU) static unsigned long from_rtc_time(struct rtc_time *tm) { return mktime(tm->tm_year+1900, tm->tm_mon+1, tm->tm_mday, tm->tm_hour, tm->tm_min, tm->tm_sec); } +#endif #ifdef CONFIG_ADB_CUDA static unsigned long cuda_get_time(void) -- cgit v1.2.3 From dcfcfe756762682d084f40b96c78507f0d27d379 Mon Sep 17 00:00:00 2001 From: Tony Breeds Date: Thu, 31 Jul 2008 16:54:20 +1000 Subject: powerpc: Guard print_device_node_tree() with #if 0 Currently print_device_node_tree() isn't called but it can be useful for debugging. Leave the function there but hide it behind '#if 0' to save it being rewritten. If you want to call it you're already editing this file anyway. ;P Signed-off-by: Tony Breeds Signed-off-by: Paul Mackerras --- arch/powerpc/platforms/pseries/eeh_driver.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/eeh_driver.c b/arch/powerpc/platforms/pseries/eeh_driver.c index 8c1ca477c52..0ad56ff7b4a 100644 --- a/arch/powerpc/platforms/pseries/eeh_driver.c +++ b/arch/powerpc/platforms/pseries/eeh_driver.c @@ -41,7 +41,7 @@ static inline const char * pcid_name (struct pci_dev *pdev) return ""; } -#ifdef DEBUG +#if 0 static void print_device_node_tree(struct pci_dn *pdn, int dent) { int i; -- cgit v1.2.3 From 611cd90c91494d1ff9bd4bc349fe38789828733e Mon Sep 17 00:00:00 2001 From: Michael Ellerman Date: Wed, 6 Aug 2008 09:10:00 +1000 Subject: powerpc: fsl_msi doesn't need it's own of_node The FSL MSI code keeps a pointer to the of_node from the device it represents. However it also has an irq_host, which contains a pointer to the of_node, so use that one instead. Signed-off-by: Michael Ellerman Signed-off-by: Paul Mackerras --- arch/powerpc/sysdev/fsl_msi.c | 12 +++++------- arch/powerpc/sysdev/fsl_msi.h | 3 --- 2 files changed, 5 insertions(+), 10 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/fsl_msi.c b/arch/powerpc/sysdev/fsl_msi.c index 2c5187cc8a2..d49fa9904d5 100644 --- a/arch/powerpc/sysdev/fsl_msi.c +++ b/arch/powerpc/sysdev/fsl_msi.c @@ -108,7 +108,8 @@ static int fsl_msi_free_dt_hwirqs(struct fsl_msi *msi) bitmap_allocate_region(msi->fsl_msi_bitmap, 0, get_count_order(NR_MSI_IRQS)); - p = of_get_property(msi->of_node, "msi-available-ranges", &len); + p = of_get_property(msi->irqhost->of_node, "msi-available-ranges", + &len); if (!p) { /* No msi-available-ranges property, @@ -120,7 +121,7 @@ static int fsl_msi_free_dt_hwirqs(struct fsl_msi *msi) if ((len % (2 * sizeof(u32))) != 0) { printk(KERN_WARNING "fsl_msi: Malformed msi-available-ranges " - "property on %s\n", msi->of_node->full_name); + "property on %s\n", msi->irqhost->of_node->full_name); return -EINVAL; } @@ -317,14 +318,11 @@ static int __devinit fsl_of_msi_probe(struct of_device *dev, goto error_out; } - msi->of_node = of_node_get(dev->node); + msi->irqhost = irq_alloc_host(dev->node, IRQ_HOST_MAP_LINEAR, + NR_MSI_IRQS, &fsl_msi_host_ops, 0); - msi->irqhost = irq_alloc_host(of_node_get(dev->node), - IRQ_HOST_MAP_LINEAR, - NR_MSI_IRQS, &fsl_msi_host_ops, 0); if (msi->irqhost == NULL) { dev_err(&dev->dev, "No memory for MSI irqhost\n"); - of_node_put(dev->node); err = -ENOMEM; goto error_out; } diff --git a/arch/powerpc/sysdev/fsl_msi.h b/arch/powerpc/sysdev/fsl_msi.h index a653468521f..6574550c00a 100644 --- a/arch/powerpc/sysdev/fsl_msi.h +++ b/arch/powerpc/sysdev/fsl_msi.h @@ -22,9 +22,6 @@ #define FSL_PIC_IP_IPIC 0x00000002 struct fsl_msi { - /* Device node of the MSI interrupt*/ - struct device_node *of_node; - struct irq_host *irqhost; unsigned long cascade_irq; -- cgit v1.2.3 From 7e302869e0c5261aba779e059cddcd2fbf7aedbe Mon Sep 17 00:00:00 2001 From: Michael Ellerman Date: Wed, 6 Aug 2008 09:10:01 +1000 Subject: powerpc: Split-out common MSI bitmap logic into msi_bitmap.c There are now two almost identical implementations of an MSI bitmap allocator, one in mpic_msi.c and the other in fsl_msi.c. Merge them together and put the result in msi_bitmap.c. Some of the MPIC bits will remain to provide a nicer interface for the MPIC users. In the process we fix two buglets. The first is that the allocation routines, now msi_bitmap_alloc_hwirqs(), returned an unsigned result, even though they use -1 to indicate allocation failure. Although all the callers were checking correctly, it is much better for the routine to just return an int. At least until someone wants > ~2 billion MSIs. The second buglet is that the device tree reservation logic only allowed power-of-two reservations. AFAICT that didn't effect any existing code but it's nicer if we can reserve arbitrary irqs from MSI use. We also add some selftests, which exposed the two buglets and now test for them, as well as some basic sanity tests. The tests are only built when CONFIG_DEBUG_KERNEL=y. Signed-off-by: Michael Ellerman Signed-off-by: Paul Mackerras --- arch/powerpc/Kconfig.debug | 5 + arch/powerpc/include/asm/msi_bitmap.h | 35 +++++ arch/powerpc/sysdev/Kconfig | 6 + arch/powerpc/sysdev/Makefile | 1 + arch/powerpc/sysdev/msi_bitmap.c | 247 ++++++++++++++++++++++++++++++++++ 5 files changed, 294 insertions(+) create mode 100644 arch/powerpc/include/asm/msi_bitmap.h create mode 100644 arch/powerpc/sysdev/msi_bitmap.c (limited to 'arch') diff --git a/arch/powerpc/Kconfig.debug b/arch/powerpc/Kconfig.debug index 4ebc52a19f0..15eb27861fc 100644 --- a/arch/powerpc/Kconfig.debug +++ b/arch/powerpc/Kconfig.debug @@ -51,6 +51,11 @@ config FTR_FIXUP_SELFTEST depends on DEBUG_KERNEL default n +config MSI_BITMAP_SELFTEST + bool "Run self-tests of the MSI bitmap code." + depends on DEBUG_KERNEL + default n + config XMON bool "Include xmon kernel debugger" depends on DEBUG_KERNEL diff --git a/arch/powerpc/include/asm/msi_bitmap.h b/arch/powerpc/include/asm/msi_bitmap.h new file mode 100644 index 00000000000..97ac3f46ae0 --- /dev/null +++ b/arch/powerpc/include/asm/msi_bitmap.h @@ -0,0 +1,35 @@ +#ifndef _POWERPC_SYSDEV_MSI_BITMAP_H +#define _POWERPC_SYSDEV_MSI_BITMAP_H + +/* + * Copyright 2008, Michael Ellerman, IBM Corporation. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; version 2 of the + * License. + * + */ + +#include +#include + +struct msi_bitmap { + struct device_node *of_node; + unsigned long *bitmap; + spinlock_t lock; + unsigned int irq_count; +}; + +int msi_bitmap_alloc_hwirqs(struct msi_bitmap *bmp, int num); +void msi_bitmap_free_hwirqs(struct msi_bitmap *bmp, unsigned int offset, + unsigned int num); +void msi_bitmap_reserve_hwirq(struct msi_bitmap *bmp, unsigned int hwirq); + +int msi_bitmap_reserve_dt_hwirqs(struct msi_bitmap *bmp); + +int msi_bitmap_alloc(struct msi_bitmap *bmp, unsigned int irq_count, + struct device_node *of_node); +void msi_bitmap_free(struct msi_bitmap *bmp); + +#endif /* _POWERPC_SYSDEV_MSI_BITMAP_H */ diff --git a/arch/powerpc/sysdev/Kconfig b/arch/powerpc/sysdev/Kconfig index 72fb35b9ebc..396582835cb 100644 --- a/arch/powerpc/sysdev/Kconfig +++ b/arch/powerpc/sysdev/Kconfig @@ -6,3 +6,9 @@ config PPC4xx_PCI_EXPRESS bool depends on PCI && 4xx default n + +config PPC_MSI_BITMAP + bool + depends on PCI_MSI + default y if MPIC + default y if FSL_PCI diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile index a90054b56d5..b6c269eb265 100644 --- a/arch/powerpc/sysdev/Makefile +++ b/arch/powerpc/sysdev/Makefile @@ -5,6 +5,7 @@ endif mpic-msi-obj-$(CONFIG_PCI_MSI) += mpic_msi.o mpic_u3msi.o mpic_pasemi_msi.o obj-$(CONFIG_MPIC) += mpic.o $(mpic-msi-obj-y) fsl-msi-obj-$(CONFIG_PCI_MSI) += fsl_msi.o +obj-$(CONFIG_PPC_MSI_BITMAP) += msi_bitmap.o obj-$(CONFIG_PPC_MPC106) += grackle.o obj-$(CONFIG_PPC_DCR_NATIVE) += dcr-low.o diff --git a/arch/powerpc/sysdev/msi_bitmap.c b/arch/powerpc/sysdev/msi_bitmap.c new file mode 100644 index 00000000000..f84217b8863 --- /dev/null +++ b/arch/powerpc/sysdev/msi_bitmap.c @@ -0,0 +1,247 @@ +/* + * Copyright 2006-2008, Michael Ellerman, IBM Corporation. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; version 2 of the + * License. + * + */ + +#include +#include +#include + +int msi_bitmap_alloc_hwirqs(struct msi_bitmap *bmp, int num) +{ + unsigned long flags; + int offset, order = get_count_order(num); + + spin_lock_irqsave(&bmp->lock, flags); + /* + * This is fast, but stricter than we need. We might want to add + * a fallback routine which does a linear search with no alignment. + */ + offset = bitmap_find_free_region(bmp->bitmap, bmp->irq_count, order); + spin_unlock_irqrestore(&bmp->lock, flags); + + pr_debug("msi_bitmap: allocated 0x%x (2^%d) at offset 0x%x\n", + num, order, offset); + + return offset; +} + +void msi_bitmap_free_hwirqs(struct msi_bitmap *bmp, unsigned int offset, + unsigned int num) +{ + unsigned long flags; + int order = get_count_order(num); + + pr_debug("msi_bitmap: freeing 0x%x (2^%d) at offset 0x%x\n", + num, order, offset); + + spin_lock_irqsave(&bmp->lock, flags); + bitmap_release_region(bmp->bitmap, offset, order); + spin_unlock_irqrestore(&bmp->lock, flags); +} + +void msi_bitmap_reserve_hwirq(struct msi_bitmap *bmp, unsigned int hwirq) +{ + unsigned long flags; + + pr_debug("msi_bitmap: reserving hwirq 0x%x\n", hwirq); + + spin_lock_irqsave(&bmp->lock, flags); + bitmap_allocate_region(bmp->bitmap, hwirq, 0); + spin_unlock_irqrestore(&bmp->lock, flags); +} + +/** + * msi_bitmap_reserve_dt_hwirqs - Reserve irqs specified in the device tree. + * @bmp: pointer to the MSI bitmap. + * + * Looks in the device tree to see if there is a property specifying which + * irqs can be used for MSI. If found those irqs reserved in the device tree + * are reserved in the bitmap. + * + * Returns 0 for success, < 0 if there was an error, and > 0 if no property + * was found in the device tree. + **/ +int msi_bitmap_reserve_dt_hwirqs(struct msi_bitmap *bmp) +{ + int i, j, len; + const u32 *p; + + if (!bmp->of_node) + return 1; + + p = of_get_property(bmp->of_node, "msi-available-ranges", &len); + if (!p) { + pr_debug("msi_bitmap: no msi-available-ranges property " \ + "found on %s\n", bmp->of_node->full_name); + return 1; + } + + if (len % (2 * sizeof(u32)) != 0) { + printk(KERN_WARNING "msi_bitmap: Malformed msi-available-ranges" + " property on %s\n", bmp->of_node->full_name); + return -EINVAL; + } + + bitmap_allocate_region(bmp->bitmap, 0, get_count_order(bmp->irq_count)); + + spin_lock(&bmp->lock); + + /* Format is: ( )+ */ + len /= 2 * sizeof(u32); + for (i = 0; i < len; i++, p += 2) { + for (j = 0; j < *(p + 1); j++) + bitmap_release_region(bmp->bitmap, *p + j, 0); + } + + spin_unlock(&bmp->lock); + + return 0; +} + +int msi_bitmap_alloc(struct msi_bitmap *bmp, unsigned int irq_count, + struct device_node *of_node) +{ + int size; + + if (!irq_count) + return -EINVAL; + + size = BITS_TO_LONGS(irq_count) * sizeof(long); + pr_debug("msi_bitmap: allocator bitmap size is 0x%x bytes\n", size); + + bmp->bitmap = zalloc_maybe_bootmem(size, GFP_KERNEL); + if (!bmp->bitmap) { + pr_debug("msi_bitmap: ENOMEM allocating allocator bitmap!\n"); + return -ENOMEM; + } + + /* We zalloc'ed the bitmap, so all irqs are free by default */ + spin_lock_init(&bmp->lock); + bmp->of_node = of_node_get(of_node); + bmp->irq_count = irq_count; + + return 0; +} + +void msi_bitmap_free(struct msi_bitmap *bmp) +{ + /* we can't free the bitmap we don't know if it's bootmem etc. */ + of_node_put(bmp->of_node); + bmp->bitmap = NULL; +} + +#ifdef CONFIG_MSI_BITMAP_SELFTEST + +#define check(x) \ + if (!(x)) printk("msi_bitmap: test failed at line %d\n", __LINE__); + +void test_basics(void) +{ + struct msi_bitmap bmp; + int i, size = 512; + + /* Can't allocate a bitmap of 0 irqs */ + check(msi_bitmap_alloc(&bmp, 0, NULL) != 0); + + /* of_node may be NULL */ + check(0 == msi_bitmap_alloc(&bmp, size, NULL)); + + /* Should all be free by default */ + check(0 == bitmap_find_free_region(bmp.bitmap, size, + get_count_order(size))); + bitmap_release_region(bmp.bitmap, 0, get_count_order(size)); + + /* With no node, there's no msi-available-ranges, so expect > 0 */ + check(msi_bitmap_reserve_dt_hwirqs(&bmp) > 0); + + /* Should all still be free */ + check(0 == bitmap_find_free_region(bmp.bitmap, size, + get_count_order(size))); + bitmap_release_region(bmp.bitmap, 0, get_count_order(size)); + + /* Check we can fill it up and then no more */ + for (i = 0; i < size; i++) + check(msi_bitmap_alloc_hwirqs(&bmp, 1) >= 0); + + check(msi_bitmap_alloc_hwirqs(&bmp, 1) < 0); + + /* Should all be allocated */ + check(bitmap_find_free_region(bmp.bitmap, size, 0) < 0); + + /* And if we free one we can then allocate another */ + msi_bitmap_free_hwirqs(&bmp, size / 2, 1); + check(msi_bitmap_alloc_hwirqs(&bmp, 1) == size / 2); + + msi_bitmap_free(&bmp); + + /* Clients may check bitmap == NULL for "not-allocated" */ + check(bmp.bitmap == NULL); + + kfree(bmp.bitmap); +} + +void test_of_node(void) +{ + u32 prop_data[] = { 10, 10, 25, 3, 40, 1, 100, 100, 200, 20 }; + const char *expected_str = "0-9,20-24,28-39,41-99,220-255"; + char *prop_name = "msi-available-ranges"; + char *node_name = "/fakenode"; + struct device_node of_node; + struct property prop; + struct msi_bitmap bmp; + int size = 256; + DECLARE_BITMAP(expected, size); + + /* There should really be a struct device_node allocator */ + memset(&of_node, 0, sizeof(of_node)); + kref_init(&of_node.kref); + of_node.full_name = node_name; + + check(0 == msi_bitmap_alloc(&bmp, size, &of_node)); + + /* No msi-available-ranges, so expect > 0 */ + check(msi_bitmap_reserve_dt_hwirqs(&bmp) > 0); + + /* Should all still be free */ + check(0 == bitmap_find_free_region(bmp.bitmap, size, + get_count_order(size))); + bitmap_release_region(bmp.bitmap, 0, get_count_order(size)); + + /* Now create a fake msi-available-ranges property */ + + /* There should really .. oh whatever */ + memset(&prop, 0, sizeof(prop)); + prop.name = prop_name; + prop.value = &prop_data; + prop.length = sizeof(prop_data); + + of_node.properties = ∝ + + /* msi-available-ranges, so expect == 0 */ + check(msi_bitmap_reserve_dt_hwirqs(&bmp) == 0); + + /* Check we got the expected result */ + check(0 == bitmap_parselist(expected_str, expected, size)); + check(bitmap_equal(expected, bmp.bitmap, size)); + + msi_bitmap_free(&bmp); + kfree(bmp.bitmap); +} + +int msi_bitmap_selftest(void) +{ + printk(KERN_DEBUG "Running MSI bitmap self-tests ...\n"); + + test_basics(); + test_of_node(); + + return 0; +} +late_initcall(msi_bitmap_selftest); +#endif /* CONFIG_MSI_BITMAP_SELFTEST */ -- cgit v1.2.3 From 7e7ab3677502a0f798f38bfa1a7d53dd22faa0bc Mon Sep 17 00:00:00 2001 From: Michael Ellerman Date: Wed, 6 Aug 2008 09:10:02 +1000 Subject: powerpc: Convert the FSL MSI code to use msi_bitmap This is 90% straight forward, although we have to change a few printk format strings as well because of the change in type of hwirq. Signed-off-by: Michael Ellerman Signed-off-by: Paul Mackerras --- arch/powerpc/sysdev/fsl_msi.c | 103 ++++++------------------------------------ arch/powerpc/sysdev/fsl_msi.h | 5 +- 2 files changed, 17 insertions(+), 91 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/fsl_msi.c b/arch/powerpc/sysdev/fsl_msi.c index d49fa9904d5..f25ce818d40 100644 --- a/arch/powerpc/sysdev/fsl_msi.c +++ b/arch/powerpc/sysdev/fsl_msi.c @@ -14,7 +14,6 @@ */ #include #include -#include #include #include #include @@ -67,96 +66,22 @@ static struct irq_host_ops fsl_msi_host_ops = { .map = fsl_msi_host_map, }; -static irq_hw_number_t fsl_msi_alloc_hwirqs(struct fsl_msi *msi, int num) -{ - unsigned long flags; - int order = get_count_order(num); - int offset; - - spin_lock_irqsave(&msi->bitmap_lock, flags); - - offset = bitmap_find_free_region(msi->fsl_msi_bitmap, - NR_MSI_IRQS, order); - - spin_unlock_irqrestore(&msi->bitmap_lock, flags); - - pr_debug("%s: allocated 0x%x (2^%d) at offset 0x%x\n", - __func__, num, order, offset); - - return offset; -} - -static void fsl_msi_free_hwirqs(struct fsl_msi *msi, int offset, int num) -{ - unsigned long flags; - int order = get_count_order(num); - - pr_debug("%s: freeing 0x%x (2^%d) at offset 0x%x\n", - __func__, num, order, offset); - - spin_lock_irqsave(&msi->bitmap_lock, flags); - bitmap_release_region(msi->fsl_msi_bitmap, offset, order); - spin_unlock_irqrestore(&msi->bitmap_lock, flags); -} - -static int fsl_msi_free_dt_hwirqs(struct fsl_msi *msi) -{ - int i; - int len; - const u32 *p; - - bitmap_allocate_region(msi->fsl_msi_bitmap, 0, - get_count_order(NR_MSI_IRQS)); - - p = of_get_property(msi->irqhost->of_node, "msi-available-ranges", - &len); - - if (!p) { - /* No msi-available-ranges property, - * All the 256 MSI interrupts can be used - */ - fsl_msi_free_hwirqs(msi, 0, 0x100); - return 0; - } - - if ((len % (2 * sizeof(u32))) != 0) { - printk(KERN_WARNING "fsl_msi: Malformed msi-available-ranges " - "property on %s\n", msi->irqhost->of_node->full_name); - return -EINVAL; - } - - /* Format is: ( )+ */ - len /= 2 * sizeof(u32); - for (i = 0; i < len; i++, p += 2) - fsl_msi_free_hwirqs(msi, *p, *(p + 1)); - - return 0; -} - static int fsl_msi_init_allocator(struct fsl_msi *msi_data) { int rc; - int size = BITS_TO_LONGS(NR_MSI_IRQS) * sizeof(u32); - msi_data->fsl_msi_bitmap = kzalloc(size, GFP_KERNEL); + rc = msi_bitmap_alloc(&msi_data->bitmap, NR_MSI_IRQS, + msi_data->irqhost->of_node); + if (rc) + return rc; - if (msi_data->fsl_msi_bitmap == NULL) { - pr_debug("%s: ENOMEM allocating allocator bitmap!\n", - __func__); - return -ENOMEM; + rc = msi_bitmap_reserve_dt_hwirqs(&msi_data->bitmap); + if (rc < 0) { + msi_bitmap_free(&msi_data->bitmap); + return rc; } - rc = fsl_msi_free_dt_hwirqs(msi_data); - if (rc) - goto out_free; - return 0; -out_free: - kfree(msi_data->fsl_msi_bitmap); - - msi_data->fsl_msi_bitmap = NULL; - return rc; - } static int fsl_msi_check_device(struct pci_dev *pdev, int nvec, int type) @@ -176,7 +101,8 @@ static void fsl_teardown_msi_irqs(struct pci_dev *pdev) if (entry->irq == NO_IRQ) continue; set_irq_msi(entry->irq, NULL); - fsl_msi_free_hwirqs(msi_data, virq_to_hw(entry->irq), 1); + msi_bitmap_free_hwirqs(&msi_data->bitmap, + virq_to_hw(entry->irq), 1); irq_dispose_mapping(entry->irq); } @@ -198,15 +124,14 @@ static void fsl_compose_msi_msg(struct pci_dev *pdev, int hwirq, static int fsl_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type) { - irq_hw_number_t hwirq; - int rc; + int rc, hwirq; unsigned int virq; struct msi_desc *entry; struct msi_msg msg; struct fsl_msi *msi_data = fsl_msi; list_for_each_entry(entry, &pdev->msi_list, list) { - hwirq = fsl_msi_alloc_hwirqs(msi_data, 1); + hwirq = msi_bitmap_alloc_hwirqs(&msi_data->bitmap, 1); if (hwirq < 0) { rc = hwirq; pr_debug("%s: fail allocating msi interrupt\n", @@ -217,9 +142,9 @@ static int fsl_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type) virq = irq_create_mapping(msi_data->irqhost, hwirq); if (virq == NO_IRQ) { - pr_debug("%s: fail mapping hwirq 0x%lx\n", + pr_debug("%s: fail mapping hwirq 0x%x\n", __func__, hwirq); - fsl_msi_free_hwirqs(msi_data, hwirq, 1); + msi_bitmap_free_hwirqs(&msi_data->bitmap, hwirq, 1); rc = -ENOSPC; goto out_free; } diff --git a/arch/powerpc/sysdev/fsl_msi.h b/arch/powerpc/sysdev/fsl_msi.h index 6574550c00a..331c7e7025b 100644 --- a/arch/powerpc/sysdev/fsl_msi.h +++ b/arch/powerpc/sysdev/fsl_msi.h @@ -13,6 +13,8 @@ #ifndef _POWERPC_SYSDEV_FSL_MSI_H #define _POWERPC_SYSDEV_FSL_MSI_H +#include + #define NR_MSI_REG 8 #define IRQS_PER_MSI_REG 32 #define NR_MSI_IRQS (NR_MSI_REG * IRQS_PER_MSI_REG) @@ -31,8 +33,7 @@ struct fsl_msi { void __iomem *msi_regs; u32 feature; - unsigned long *fsl_msi_bitmap; - spinlock_t bitmap_lock; + struct msi_bitmap bitmap; }; #endif /* _POWERPC_SYSDEV_FSL_MSI_H */ -- cgit v1.2.3 From 25235f712b680d00756a73ee64289137989fc6fd Mon Sep 17 00:00:00 2001 From: Michael Ellerman Date: Wed, 6 Aug 2008 09:10:03 +1000 Subject: powerpc: Convert the MPIC MSI code to use msi_bitmap This affects the U3 MSI code as well as the PASEMI MSI code. We keep some of the MPIC routines as helpers, and also the U3 best-guess reservation logic. The rest is replaced by the generic code. And a few printk format changes due to hwirq type change. Signed-off-by: Michael Ellerman Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/mpic.h | 4 +- arch/powerpc/sysdev/mpic.h | 2 - arch/powerpc/sysdev/mpic_msi.c | 123 +++++----------------------------- arch/powerpc/sysdev/mpic_pasemi_msi.c | 24 ++++--- arch/powerpc/sysdev/mpic_u3msi.c | 22 +++--- 5 files changed, 44 insertions(+), 131 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/mpic.h b/arch/powerpc/include/asm/mpic.h index fe566a348a8..34d9ac433ac 100644 --- a/arch/powerpc/include/asm/mpic.h +++ b/arch/powerpc/include/asm/mpic.h @@ -5,6 +5,7 @@ #include #include #include +#include /* * Global registers @@ -301,8 +302,7 @@ struct mpic #endif #ifdef CONFIG_PCI_MSI - spinlock_t bitmap_lock; - unsigned long *hwirq_bitmap; + struct msi_bitmap msi_bitmap; #endif #ifdef CONFIG_MPIC_BROKEN_REGREAD diff --git a/arch/powerpc/sysdev/mpic.h b/arch/powerpc/sysdev/mpic.h index fbf8a266941..6209c62a426 100644 --- a/arch/powerpc/sysdev/mpic.h +++ b/arch/powerpc/sysdev/mpic.h @@ -14,8 +14,6 @@ #ifdef CONFIG_PCI_MSI extern void mpic_msi_reserve_hwirq(struct mpic *mpic, irq_hw_number_t hwirq); extern int mpic_msi_init_allocator(struct mpic *mpic); -extern irq_hw_number_t mpic_msi_alloc_hwirqs(struct mpic *mpic, int num); -extern void mpic_msi_free_hwirqs(struct mpic *mpic, int offset, int num); extern int mpic_u3msi_init(struct mpic *mpic); extern int mpic_pasemi_msi_init(struct mpic *mpic); #else diff --git a/arch/powerpc/sysdev/mpic_msi.c b/arch/powerpc/sysdev/mpic_msi.c index de3e5e8bc32..1d44eee80fa 100644 --- a/arch/powerpc/sysdev/mpic_msi.c +++ b/arch/powerpc/sysdev/mpic_msi.c @@ -15,59 +15,17 @@ #include #include #include +#include #include -static void __mpic_msi_reserve_hwirq(struct mpic *mpic, irq_hw_number_t hwirq) -{ - pr_debug("mpic: reserving hwirq 0x%lx\n", hwirq); - bitmap_allocate_region(mpic->hwirq_bitmap, hwirq, 0); -} - void mpic_msi_reserve_hwirq(struct mpic *mpic, irq_hw_number_t hwirq) { - unsigned long flags; - /* The mpic calls this even when there is no allocator setup */ - if (!mpic->hwirq_bitmap) + if (!mpic->msi_bitmap.bitmap) return; - spin_lock_irqsave(&mpic->bitmap_lock, flags); - __mpic_msi_reserve_hwirq(mpic, hwirq); - spin_unlock_irqrestore(&mpic->bitmap_lock, flags); -} - -irq_hw_number_t mpic_msi_alloc_hwirqs(struct mpic *mpic, int num) -{ - unsigned long flags; - int offset, order = get_count_order(num); - - spin_lock_irqsave(&mpic->bitmap_lock, flags); - /* - * This is fast, but stricter than we need. We might want to add - * a fallback routine which does a linear search with no alignment. - */ - offset = bitmap_find_free_region(mpic->hwirq_bitmap, mpic->irq_count, - order); - spin_unlock_irqrestore(&mpic->bitmap_lock, flags); - - pr_debug("mpic: allocated 0x%x (2^%d) at offset 0x%x\n", - num, order, offset); - - return offset; -} - -void mpic_msi_free_hwirqs(struct mpic *mpic, int offset, int num) -{ - unsigned long flags; - int order = get_count_order(num); - - pr_debug("mpic: freeing 0x%x (2^%d) at offset 0x%x\n", - num, order, offset); - - spin_lock_irqsave(&mpic->bitmap_lock, flags); - bitmap_release_region(mpic->hwirq_bitmap, offset, order); - spin_unlock_irqrestore(&mpic->bitmap_lock, flags); + msi_bitmap_reserve_hwirq(&mpic->msi_bitmap, hwirq); } #ifdef CONFIG_MPIC_U3_HT_IRQS @@ -83,13 +41,13 @@ static int mpic_msi_reserve_u3_hwirqs(struct mpic *mpic) /* Reserve source numbers we know are reserved in the HW */ for (i = 0; i < 8; i++) - __mpic_msi_reserve_hwirq(mpic, i); + msi_bitmap_reserve_hwirq(&mpic->msi_bitmap, i); for (i = 42; i < 46; i++) - __mpic_msi_reserve_hwirq(mpic, i); + msi_bitmap_reserve_hwirq(&mpic->msi_bitmap, i); for (i = 100; i < 105; i++) - __mpic_msi_reserve_hwirq(mpic, i); + msi_bitmap_reserve_hwirq(&mpic->msi_bitmap, i); np = NULL; while ((np = of_find_all_nodes(np))) { @@ -99,7 +57,7 @@ static int mpic_msi_reserve_u3_hwirqs(struct mpic *mpic) while (of_irq_map_one(np, index++, &oirq) == 0) { ops->xlate(mpic->irqhost, NULL, oirq.specifier, oirq.size, &hwirq, &flags); - __mpic_msi_reserve_hwirq(mpic, hwirq); + msi_bitmap_reserve_hwirq(&mpic->msi_bitmap, hwirq); } } @@ -112,70 +70,25 @@ static int mpic_msi_reserve_u3_hwirqs(struct mpic *mpic) } #endif -static int mpic_msi_reserve_dt_hwirqs(struct mpic *mpic) -{ - int i, len; - const u32 *p; - - p = of_get_property(mpic->irqhost->of_node, - "msi-available-ranges", &len); - if (!p) { - pr_debug("mpic: no msi-available-ranges property found on %s\n", - mpic->irqhost->of_node->full_name); - return -ENODEV; - } - - if (len % 8 != 0) { - printk(KERN_WARNING "mpic: Malformed msi-available-ranges " - "property on %s\n", mpic->irqhost->of_node->full_name); - return -EINVAL; - } - - bitmap_allocate_region(mpic->hwirq_bitmap, 0, - get_count_order(mpic->irq_count)); - - /* Format is: ( )+ */ - len /= sizeof(u32); - for (i = 0; i < len / 2; i++, p += 2) - mpic_msi_free_hwirqs(mpic, *p, *(p + 1)); - - return 0; -} - int mpic_msi_init_allocator(struct mpic *mpic) { - int rc, size; - - BUG_ON(mpic->hwirq_bitmap); - spin_lock_init(&mpic->bitmap_lock); + int rc; - size = BITS_TO_LONGS(mpic->irq_count) * sizeof(long); - pr_debug("mpic: allocator bitmap size is 0x%x bytes\n", size); + rc = msi_bitmap_alloc(&mpic->msi_bitmap, mpic->irq_count, + mpic->irqhost->of_node); + if (rc) + return rc; - mpic->hwirq_bitmap = alloc_maybe_bootmem(size, GFP_KERNEL); - - if (!mpic->hwirq_bitmap) { - pr_debug("mpic: ENOMEM allocating allocator bitmap!\n"); - return -ENOMEM; - } - - memset(mpic->hwirq_bitmap, 0, size); - - rc = mpic_msi_reserve_dt_hwirqs(mpic); - if (rc) { + rc = msi_bitmap_reserve_dt_hwirqs(&mpic->msi_bitmap); + if (rc > 0) { if (mpic->flags & MPIC_U3_HT_IRQS) rc = mpic_msi_reserve_u3_hwirqs(mpic); - if (rc) - goto out_free; + if (rc) { + msi_bitmap_free(&mpic->msi_bitmap); + return rc; + } } return 0; - - out_free: - if (mem_init_done) - kfree(mpic->hwirq_bitmap); - - mpic->hwirq_bitmap = NULL; - return rc; } diff --git a/arch/powerpc/sysdev/mpic_pasemi_msi.c b/arch/powerpc/sysdev/mpic_pasemi_msi.c index 68aff607667..656cb772b69 100644 --- a/arch/powerpc/sysdev/mpic_pasemi_msi.c +++ b/arch/powerpc/sysdev/mpic_pasemi_msi.c @@ -22,6 +22,7 @@ #include #include #include +#include #include "mpic.h" @@ -81,8 +82,8 @@ static void pasemi_msi_teardown_msi_irqs(struct pci_dev *pdev) continue; set_irq_msi(entry->irq, NULL); - mpic_msi_free_hwirqs(msi_mpic, virq_to_hw(entry->irq), - ALLOC_CHUNK); + msi_bitmap_free_hwirqs(&msi_mpic->msi_bitmap, + virq_to_hw(entry->irq), ALLOC_CHUNK); irq_dispose_mapping(entry->irq); } @@ -91,11 +92,10 @@ static void pasemi_msi_teardown_msi_irqs(struct pci_dev *pdev) static int pasemi_msi_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type) { - irq_hw_number_t hwirq; unsigned int virq; struct msi_desc *entry; struct msi_msg msg; - int ret; + int hwirq; pr_debug("pasemi_msi_setup_msi_irqs, pdev %p nvec %d type %d\n", pdev, nvec, type); @@ -109,17 +109,19 @@ static int pasemi_msi_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type) * few MSIs for someone, but restrictions will apply to how the * sources can be changed independently. */ - ret = mpic_msi_alloc_hwirqs(msi_mpic, ALLOC_CHUNK); - hwirq = ret; - if (ret < 0) { + hwirq = msi_bitmap_alloc_hwirqs(&msi_mpic->msi_bitmap, + ALLOC_CHUNK); + if (hwirq < 0) { pr_debug("pasemi_msi: failed allocating hwirq\n"); return hwirq; } virq = irq_create_mapping(msi_mpic->irqhost, hwirq); if (virq == NO_IRQ) { - pr_debug("pasemi_msi: failed mapping hwirq 0x%lx\n", hwirq); - mpic_msi_free_hwirqs(msi_mpic, hwirq, ALLOC_CHUNK); + pr_debug("pasemi_msi: failed mapping hwirq 0x%x\n", + hwirq); + msi_bitmap_free_hwirqs(&msi_mpic->msi_bitmap, hwirq, + ALLOC_CHUNK); return -ENOSPC; } @@ -133,8 +135,8 @@ static int pasemi_msi_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type) set_irq_chip(virq, &mpic_pasemi_msi_chip); set_irq_type(virq, IRQ_TYPE_EDGE_RISING); - pr_debug("pasemi_msi: allocated virq 0x%x (hw 0x%lx) addr 0x%x\n", - virq, hwirq, msg.address_lo); + pr_debug("pasemi_msi: allocated virq 0x%x (hw 0x%x) " \ + "addr 0x%x\n", virq, hwirq, msg.address_lo); /* Likewise, the device writes [0...511] into the target * register to generate MSI [512...1023] diff --git a/arch/powerpc/sysdev/mpic_u3msi.c b/arch/powerpc/sysdev/mpic_u3msi.c index 6e2f8686fdf..0a8f5a9e87c 100644 --- a/arch/powerpc/sysdev/mpic_u3msi.c +++ b/arch/powerpc/sysdev/mpic_u3msi.c @@ -16,6 +16,7 @@ #include #include #include +#include #include "mpic.h" @@ -101,7 +102,8 @@ static void u3msi_teardown_msi_irqs(struct pci_dev *pdev) continue; set_irq_msi(entry->irq, NULL); - mpic_msi_free_hwirqs(msi_mpic, virq_to_hw(entry->irq), 1); + msi_bitmap_free_hwirqs(&msi_mpic->msi_bitmap, + virq_to_hw(entry->irq), 1); irq_dispose_mapping(entry->irq); } @@ -110,29 +112,27 @@ static void u3msi_teardown_msi_irqs(struct pci_dev *pdev) static int u3msi_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type) { - irq_hw_number_t hwirq; unsigned int virq; struct msi_desc *entry; struct msi_msg msg; u64 addr; - int ret; + int hwirq; addr = find_ht_magic_addr(pdev); msg.address_lo = addr & 0xFFFFFFFF; msg.address_hi = addr >> 32; list_for_each_entry(entry, &pdev->msi_list, list) { - ret = mpic_msi_alloc_hwirqs(msi_mpic, 1); - if (ret < 0) { + hwirq = msi_bitmap_alloc_hwirqs(&msi_mpic->msi_bitmap, 1); + if (hwirq < 0) { pr_debug("u3msi: failed allocating hwirq\n"); - return ret; + return hwirq; } - hwirq = ret; virq = irq_create_mapping(msi_mpic->irqhost, hwirq); if (virq == NO_IRQ) { - pr_debug("u3msi: failed mapping hwirq 0x%lx\n", hwirq); - mpic_msi_free_hwirqs(msi_mpic, hwirq, 1); + pr_debug("u3msi: failed mapping hwirq 0x%x\n", hwirq); + msi_bitmap_free_hwirqs(&msi_mpic->msi_bitmap, hwirq, 1); return -ENOSPC; } @@ -140,8 +140,8 @@ static int u3msi_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type) set_irq_chip(virq, &mpic_u3msi_chip); set_irq_type(virq, IRQ_TYPE_EDGE_RISING); - pr_debug("u3msi: allocated virq 0x%x (hw 0x%lx) addr 0x%lx\n", - virq, hwirq, addr); + pr_debug("u3msi: allocated virq 0x%x (hw 0x%x) addr 0x%lx\n", + virq, hwirq, (unsigned long)addr); msg.data = hwirq; write_msi_msg(virq, &msg); -- cgit v1.2.3 From 0ec27c049d80535f77901654a310b090106b046c Mon Sep 17 00:00:00 2001 From: Stephen Rothwell Date: Thu, 7 Aug 2008 10:30:40 +1000 Subject: powerpc: Remove include of linux/of_platform.h from asm/of_platform.h Now that we have removed all inclusions of asm/of_platform.h, this compatibility include can be removed. Signed-off-by: Stephen Rothwell Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/of_platform.h | 3 --- 1 file changed, 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/of_platform.h b/arch/powerpc/include/asm/of_platform.h index 18659ef7213..53b46507ffd 100644 --- a/arch/powerpc/include/asm/of_platform.h +++ b/arch/powerpc/include/asm/of_platform.h @@ -11,9 +11,6 @@ * */ -/* This is just here during the transition */ -#include - /* Platform drivers register/unregister */ static inline int of_register_platform_driver(struct of_platform_driver *drv) { -- cgit v1.2.3 From ed95d7450dcbfeb45ffc9d39b1747aee82b49a51 Mon Sep 17 00:00:00 2001 From: David Gibson Date: Thu, 7 Aug 2008 12:24:17 +1000 Subject: powerpc: Update in-kernel dtc and libfdt to version 1.2.0 Some time ago, a copies of the upstream dtc and libfdt sources were included in the kernel tree to avoid having these as external dependencies for building the kernel. Since then development on the upstream dtc and libfdt has continued. This updates the in-kernel versions to match the recently released upstream dtc version 1.2.0. This includes a number of bugfixes, many cleanups and a few new features. Signed-off-by: David Gibson Signed-off-by: Paul Mackerras --- arch/powerpc/boot/dtc-src/Makefile.dtc | 18 +- arch/powerpc/boot/dtc-src/checks.c | 305 ++++---------- arch/powerpc/boot/dtc-src/data.c | 62 +-- arch/powerpc/boot/dtc-src/dtc-lexer.l | 120 +++--- arch/powerpc/boot/dtc-src/dtc-lexer.lex.c_shipped | 445 +++++++++++---------- arch/powerpc/boot/dtc-src/dtc-parser.tab.c_shipped | 387 ++++++++++-------- arch/powerpc/boot/dtc-src/dtc-parser.tab.h_shipped | 12 +- arch/powerpc/boot/dtc-src/dtc-parser.y | 67 +++- arch/powerpc/boot/dtc-src/dtc.c | 41 +- arch/powerpc/boot/dtc-src/dtc.h | 43 +- arch/powerpc/boot/dtc-src/flattree.c | 232 ++++------- arch/powerpc/boot/dtc-src/fstree.c | 8 +- arch/powerpc/boot/dtc-src/libfdt_env.h | 23 ++ arch/powerpc/boot/dtc-src/livetree.c | 9 +- arch/powerpc/boot/dtc-src/srcpos.c | 121 +++--- arch/powerpc/boot/dtc-src/srcpos.h | 30 +- arch/powerpc/boot/dtc-src/treesource.c | 15 +- arch/powerpc/boot/dtc-src/version_gen.h | 2 +- arch/powerpc/boot/libfdt/Makefile.libfdt | 8 +- arch/powerpc/boot/libfdt/fdt.c | 61 ++- arch/powerpc/boot/libfdt/fdt_ro.c | 329 +++++---------- arch/powerpc/boot/libfdt/fdt_rw.c | 200 ++++----- arch/powerpc/boot/libfdt/fdt_strerror.c | 34 +- arch/powerpc/boot/libfdt/fdt_sw.c | 55 ++- arch/powerpc/boot/libfdt/fdt_wip.c | 9 +- arch/powerpc/boot/libfdt/libfdt.h | 383 +++++++++++++++++- arch/powerpc/boot/libfdt/libfdt_internal.h | 24 +- arch/powerpc/boot/libfdt_env.h | 1 + 28 files changed, 1615 insertions(+), 1429 deletions(-) create mode 100644 arch/powerpc/boot/dtc-src/libfdt_env.h (limited to 'arch') diff --git a/arch/powerpc/boot/dtc-src/Makefile.dtc b/arch/powerpc/boot/dtc-src/Makefile.dtc index d607fdb8df8..6ddf9ecac66 100644 --- a/arch/powerpc/boot/dtc-src/Makefile.dtc +++ b/arch/powerpc/boot/dtc-src/Makefile.dtc @@ -5,21 +5,5 @@ # DTC_SRCS = dtc.c flattree.c fstree.c data.c livetree.c treesource.c srcpos.c \ checks.c -DTC_EXTRA = dtc.h srcpos.h -DTC_LEXFILES = dtc-lexer.l -DTC_BISONFILES = dtc-parser.y - -DTC_LEX_SRCS = $(DTC_LEXFILES:%.l=%.lex.c) -DTC_BISON_SRCS = $(DTC_BISONFILES:%.y=%.tab.c) -DTC_BISON_INCLUDES = $(DTC_BISONFILES:%.y=%.tab.h) - -DTC_GEN_SRCS = $(DTC_LEX_SRCS) $(DTC_BISON_SRCS) -DTC_GEN_ALL = $(DTC_GEN_SRCS) $(DTC_BISON_INCLUDES) +DTC_GEN_SRCS = dtc-lexer.lex.c dtc-parser.tab.c DTC_OBJS = $(DTC_SRCS:%.c=%.o) $(DTC_GEN_SRCS:%.c=%.o) - -DTC_CLEANFILES = $(DTC_GEN_ALL) - -# We assume the containing Makefile system can do auto-dependencies for most -# things, but we supply the dependencies on generated header files explicitly - -$(addprefix $(DTC_objdir)/,$(DTC_GEN_SRCS:%.c=%.o)): $(addprefix $(DTC_objdir)/,$(DTC_BISON_INCLUDES)) diff --git a/arch/powerpc/boot/dtc-src/checks.c b/arch/powerpc/boot/dtc-src/checks.c index 2ce961cd414..95485796f25 100644 --- a/arch/powerpc/boot/dtc-src/checks.c +++ b/arch/powerpc/boot/dtc-src/checks.c @@ -242,6 +242,42 @@ static void check_duplicate_property_names(struct check *c, struct node *dt, } NODE_CHECK(duplicate_property_names, NULL, ERROR); +#define LOWERCASE "abcdefghijklmnopqrstuvwxyz" +#define UPPERCASE "ABCDEFGHIJKLMNOPQRSTUVWXYZ" +#define DIGITS "0123456789" +#define PROPNODECHARS LOWERCASE UPPERCASE DIGITS ",._+*#?-" + +static void check_node_name_chars(struct check *c, struct node *dt, + struct node *node) +{ + int n = strspn(node->name, c->data); + + if (n < strlen(node->name)) + FAIL(c, "Bad character '%c' in node %s", + node->name[n], node->fullpath); +} +NODE_CHECK(node_name_chars, PROPNODECHARS "@", ERROR); + +static void check_node_name_format(struct check *c, struct node *dt, + struct node *node) +{ + if (strchr(get_unitname(node), '@')) + FAIL(c, "Node %s has multiple '@' characters in name", + node->fullpath); +} +NODE_CHECK(node_name_format, NULL, ERROR, &node_name_chars); + +static void check_property_name_chars(struct check *c, struct node *dt, + struct node *node, struct property *prop) +{ + int n = strspn(prop->name, c->data); + + if (n < strlen(prop->name)) + FAIL(c, "Bad character '%c' in property name \"%s\", node %s", + prop->name[n], prop->name, node->fullpath); +} +PROP_CHECK(property_name_chars, PROPNODECHARS, ERROR); + static void check_explicit_phandles(struct check *c, struct node *root, struct node *node) { @@ -280,16 +316,29 @@ NODE_CHECK(explicit_phandles, NULL, ERROR); static void check_name_properties(struct check *c, struct node *root, struct node *node) { - struct property *prop; + struct property **pp, *prop = NULL; + + for (pp = &node->proplist; *pp; pp = &((*pp)->next)) + if (streq((*pp)->name, "name")) { + prop = *pp; + break; + } - prop = get_property(node, "name"); if (!prop) return; /* No name property, that's fine */ if ((prop->val.len != node->basenamelen+1) - || (memcmp(prop->val.val, node->name, node->basenamelen) != 0)) + || (memcmp(prop->val.val, node->name, node->basenamelen) != 0)) { FAIL(c, "\"name\" property in %s is incorrect (\"%s\" instead" " of base node name)", node->fullpath, prop->val.val); + } else { + /* The name property is correct, and therefore redundant. + * Delete it */ + *pp = prop->next; + free(prop->name); + data_free(prop->val); + free(prop); + } } CHECK_IS_STRING(name_is_string, "name", ERROR); NODE_CHECK(name_properties, NULL, ERROR, &name_is_string); @@ -301,23 +350,23 @@ NODE_CHECK(name_properties, NULL, ERROR, &name_is_string); static void fixup_phandle_references(struct check *c, struct node *dt, struct node *node, struct property *prop) { - struct marker *m = prop->val.markers; - struct node *refnode; - cell_t phandle; - - for_each_marker_of_type(m, REF_PHANDLE) { - assert(m->offset + sizeof(cell_t) <= prop->val.len); - - refnode = get_node_by_ref(dt, m->ref); - if (! refnode) { - FAIL(c, "Reference to non-existent node or label \"%s\"\n", - m->ref); - continue; - } - - phandle = get_node_phandle(dt, refnode); - *((cell_t *)(prop->val.val + m->offset)) = cpu_to_be32(phandle); - } + struct marker *m = prop->val.markers; + struct node *refnode; + cell_t phandle; + + for_each_marker_of_type(m, REF_PHANDLE) { + assert(m->offset + sizeof(cell_t) <= prop->val.len); + + refnode = get_node_by_ref(dt, m->ref); + if (! refnode) { + FAIL(c, "Reference to non-existent node or label \"%s\"\n", + m->ref); + continue; + } + + phandle = get_node_phandle(dt, refnode); + *((cell_t *)(prop->val.val + m->offset)) = cpu_to_fdt32(phandle); + } } CHECK(phandle_references, NULL, NULL, fixup_phandle_references, NULL, ERROR, &duplicate_node_names, &explicit_phandles); @@ -498,6 +547,7 @@ TREE_CHECK(obsolete_chosen_interrupt_controller, NULL, WARN); static struct check *check_table[] = { &duplicate_node_names, &duplicate_property_names, + &node_name_chars, &node_name_format, &property_name_chars, &name_is_string, &name_properties, &explicit_phandles, &phandle_references, &path_references, @@ -511,10 +561,7 @@ static struct check *check_table[] = { &obsolete_chosen_interrupt_controller, }; -int check_semantics(struct node *dt, int outversion, int boot_cpuid_phys); - -void process_checks(int force, struct boot_info *bi, - int checkflag, int outversion, int boot_cpuid_phys) +void process_checks(int force, struct boot_info *bi) { struct node *dt = bi->dt; int i; @@ -537,214 +584,4 @@ void process_checks(int force, struct boot_info *bi, "output forced\n"); } } - - if (checkflag) { - if (error) { - fprintf(stderr, "Warning: Skipping semantic checks due to structural errors\n"); - } else { - if (!check_semantics(bi->dt, outversion, - boot_cpuid_phys)) - fprintf(stderr, "Warning: Input tree has semantic errors\n"); - } - } -} - -/* - * Semantic check functions - */ - -#define ERRMSG(...) if (quiet < 2) fprintf(stderr, "ERROR: " __VA_ARGS__) -#define WARNMSG(...) if (quiet < 1) fprintf(stderr, "Warning: " __VA_ARGS__) - -#define DO_ERR(...) do {ERRMSG(__VA_ARGS__); ok = 0; } while (0) - -#define CHECK_HAVE(node, propname) \ - do { \ - if (! (prop = get_property((node), (propname)))) \ - DO_ERR("Missing \"%s\" property in %s\n", (propname), \ - (node)->fullpath); \ - } while (0); - -#define CHECK_HAVE_WARN(node, propname) \ - do { \ - if (! (prop = get_property((node), (propname)))) \ - WARNMSG("%s has no \"%s\" property\n", \ - (node)->fullpath, (propname)); \ - } while (0) - -#define CHECK_HAVE_STRING(node, propname) \ - do { \ - CHECK_HAVE((node), (propname)); \ - if (prop && !data_is_one_string(prop->val)) \ - DO_ERR("\"%s\" property in %s is not a string\n", \ - (propname), (node)->fullpath); \ - } while (0) - -#define CHECK_HAVE_STREQ(node, propname, value) \ - do { \ - CHECK_HAVE_STRING((node), (propname)); \ - if (prop && !streq(prop->val.val, (value))) \ - DO_ERR("%s has wrong %s, %s (should be %s\n", \ - (node)->fullpath, (propname), \ - prop->val.val, (value)); \ - } while (0) - -#define CHECK_HAVE_ONECELL(node, propname) \ - do { \ - CHECK_HAVE((node), (propname)); \ - if (prop && (prop->val.len != sizeof(cell_t))) \ - DO_ERR("\"%s\" property in %s has wrong size %d (should be 1 cell)\n", (propname), (node)->fullpath, prop->val.len); \ - } while (0) - -#define CHECK_HAVE_WARN_ONECELL(node, propname) \ - do { \ - CHECK_HAVE_WARN((node), (propname)); \ - if (prop && (prop->val.len != sizeof(cell_t))) \ - DO_ERR("\"%s\" property in %s has wrong size %d (should be 1 cell)\n", (propname), (node)->fullpath, prop->val.len); \ - } while (0) - -#define CHECK_HAVE_WARN_PHANDLE(xnode, propname, root) \ - do { \ - struct node *ref; \ - CHECK_HAVE_WARN_ONECELL((xnode), (propname)); \ - if (prop) {\ - cell_t phandle = propval_cell(prop); \ - if ((phandle == 0) || (phandle == -1)) { \ - DO_ERR("\"%s\" property in %s contains an invalid phandle %x\n", (propname), (xnode)->fullpath, phandle); \ - } else { \ - ref = get_node_by_phandle((root), propval_cell(prop)); \ - if (! ref) \ - DO_ERR("\"%s\" property in %s refers to non-existant phandle %x\n", (propname), (xnode)->fullpath, propval_cell(prop)); \ - } \ - } \ - } while (0) - -#define CHECK_HAVE_WARN_STRING(node, propname) \ - do { \ - CHECK_HAVE_WARN((node), (propname)); \ - if (prop && !data_is_one_string(prop->val)) \ - DO_ERR("\"%s\" property in %s is not a string\n", \ - (propname), (node)->fullpath); \ - } while (0) - -static int check_root(struct node *root) -{ - struct property *prop; - int ok = 1; - - CHECK_HAVE_STRING(root, "model"); - CHECK_HAVE_WARN(root, "compatible"); - - return ok; -} - -static int check_cpus(struct node *root, int outversion, int boot_cpuid_phys) -{ - struct node *cpus, *cpu; - struct property *prop; - struct node *bootcpu = NULL; - int ok = 1; - - cpus = get_subnode(root, "cpus"); - if (! cpus) { - ERRMSG("Missing /cpus node\n"); - return 0; - } - - if (cpus->addr_cells != 1) - DO_ERR("%s has bad #address-cells value %d (should be 1)\n", - cpus->fullpath, cpus->addr_cells); - if (cpus->size_cells != 0) - DO_ERR("%s has bad #size-cells value %d (should be 0)\n", - cpus->fullpath, cpus->size_cells); - - for_each_child(cpus, cpu) { - CHECK_HAVE_STREQ(cpu, "device_type", "cpu"); - - CHECK_HAVE_ONECELL(cpu, "reg"); - if (prop) { - cell_t unitnum; - char *eptr; - - unitnum = strtol(get_unitname(cpu), &eptr, 16); - if (*eptr) { - WARNMSG("%s has bad format unit name %s (should be CPU number\n", - cpu->fullpath, get_unitname(cpu)); - } else if (unitnum != propval_cell(prop)) { - WARNMSG("%s unit name \"%s\" does not match \"reg\" property <%x>\n", - cpu->fullpath, get_unitname(cpu), - propval_cell(prop)); - } - } - -/* CHECK_HAVE_ONECELL(cpu, "d-cache-line-size"); */ -/* CHECK_HAVE_ONECELL(cpu, "i-cache-line-size"); */ - CHECK_HAVE_ONECELL(cpu, "d-cache-size"); - CHECK_HAVE_ONECELL(cpu, "i-cache-size"); - - CHECK_HAVE_WARN_ONECELL(cpu, "clock-frequency"); - CHECK_HAVE_WARN_ONECELL(cpu, "timebase-frequency"); - - prop = get_property(cpu, "linux,boot-cpu"); - if (prop) { - if (prop->val.len) - WARNMSG("\"linux,boot-cpu\" property in %s is non-empty\n", - cpu->fullpath); - if (bootcpu) - DO_ERR("Multiple boot cpus (%s and %s)\n", - bootcpu->fullpath, cpu->fullpath); - else - bootcpu = cpu; - } - } - - if (outversion < 2) { - if (! bootcpu) - WARNMSG("No cpu has \"linux,boot-cpu\" property\n"); - } else { - if (bootcpu) - WARNMSG("\"linux,boot-cpu\" property is deprecated in blob version 2 or higher\n"); - if (boot_cpuid_phys == 0xfeedbeef) - WARNMSG("physical boot CPU not set. Use -b option to set\n"); - } - - return ok; -} - -static int check_memory(struct node *root) -{ - struct node *mem; - struct property *prop; - int nnodes = 0; - int ok = 1; - - for_each_child(root, mem) { - if (! strneq(mem->name, "memory", mem->basenamelen)) - continue; - - nnodes++; - - CHECK_HAVE_STREQ(mem, "device_type", "memory"); - CHECK_HAVE(mem, "reg"); - } - - if (nnodes == 0) { - ERRMSG("No memory nodes\n"); - return 0; - } - - return ok; -} - -int check_semantics(struct node *dt, int outversion, int boot_cpuid_phys) -{ - int ok = 1; - - ok = ok && check_root(dt); - ok = ok && check_cpus(dt, outversion, boot_cpuid_phys); - ok = ok && check_memory(dt); - if (! ok) - return 0; - - return 1; } diff --git a/arch/powerpc/boot/dtc-src/data.c b/arch/powerpc/boot/dtc-src/data.c index a94718c731a..dd2e3d39d4c 100644 --- a/arch/powerpc/boot/dtc-src/data.c +++ b/arch/powerpc/boot/dtc-src/data.c @@ -32,8 +32,6 @@ void data_free(struct data d) m = nm; } - assert(!d.val || d.asize); - if (d.val) free(d.val); } @@ -43,9 +41,6 @@ struct data data_grow_for(struct data d, int xlen) struct data nd; int newsize; - /* we must start with an allocated datum */ - assert(!d.val || d.asize); - if (xlen == 0) return d; @@ -56,11 +51,8 @@ struct data data_grow_for(struct data d, int xlen) while ((d.len + xlen) > newsize) newsize *= 2; - nd.asize = newsize; nd.val = xrealloc(d.val, newsize); - assert(nd.asize >= (d.len + xlen)); - return nd; } @@ -83,16 +75,11 @@ static char get_oct_char(const char *s, int *i) long val; x[3] = '\0'; - x[0] = s[(*i)]; - if (x[0]) { - x[1] = s[(*i)+1]; - if (x[1]) - x[2] = s[(*i)+2]; - } + strncpy(x, s + *i, 3); val = strtol(x, &endx, 8); - if ((endx - x) == 0) - fprintf(stderr, "Empty \\nnn escape\n"); + + assert(endx > x); (*i) += endx - x; return val; @@ -105,13 +92,11 @@ static char get_hex_char(const char *s, int *i) long val; x[2] = '\0'; - x[0] = s[(*i)]; - if (x[0]) - x[1] = s[(*i)+1]; + strncpy(x, s + *i, 2); val = strtol(x, &endx, 16); - if ((endx - x) == 0) - fprintf(stderr, "Empty \\x escape\n"); + if (!(endx > x)) + die("\\x used with no following hex digits\n"); (*i) += endx - x; return val; @@ -182,14 +167,29 @@ struct data data_copy_escape_string(const char *s, int len) return d; } -struct data data_copy_file(FILE *f, size_t len) +struct data data_copy_file(FILE *f, size_t maxlen) { - struct data d; + struct data d = empty_data; - d = data_grow_for(empty_data, len); + while (!feof(f) && (d.len < maxlen)) { + size_t chunksize, ret; - d.len = len; - fread(d.val, len, 1, f); + if (maxlen == -1) + chunksize = 4096; + else + chunksize = maxlen - d.len; + + d = data_grow_for(d, chunksize); + ret = fread(d.val + d.len, 1, chunksize, f); + + if (ferror(f)) + die("Error reading file into data: %s", strerror(errno)); + + if (d.len + ret < d.len) + die("Overflow reading file into data\n"); + + d.len += ret; + } return d; } @@ -247,7 +247,7 @@ struct data data_merge(struct data d1, struct data d2) struct data data_append_cell(struct data d, cell_t word) { - cell_t beword = cpu_to_be32(word); + cell_t beword = cpu_to_fdt32(word); return data_append_data(d, &beword, sizeof(beword)); } @@ -256,15 +256,15 @@ struct data data_append_re(struct data d, const struct fdt_reserve_entry *re) { struct fdt_reserve_entry bere; - bere.address = cpu_to_be64(re->address); - bere.size = cpu_to_be64(re->size); + bere.address = cpu_to_fdt64(re->address); + bere.size = cpu_to_fdt64(re->size); return data_append_data(d, &bere, sizeof(bere)); } -struct data data_append_addr(struct data d, u64 addr) +struct data data_append_addr(struct data d, uint64_t addr) { - u64 beaddr = cpu_to_be64(addr); + uint64_t beaddr = cpu_to_fdt64(addr); return data_append_data(d, &beaddr, sizeof(beaddr)); } diff --git a/arch/powerpc/boot/dtc-src/dtc-lexer.l b/arch/powerpc/boot/dtc-src/dtc-lexer.l index c811b221b31..44dbfd3f097 100644 --- a/arch/powerpc/boot/dtc-src/dtc-lexer.l +++ b/arch/powerpc/boot/dtc-src/dtc-lexer.l @@ -28,6 +28,10 @@ PROPNODECHAR [a-zA-Z0-9,._+*#?@-] PATHCHAR ({PROPNODECHAR}|[/]) LABEL [a-zA-Z_][a-zA-Z0-9_]* +STRING \"([^\\"]|\\.)*\" +WS [[:space:]] +COMMENT "/*"([^*]|\*+[^*/])*\*+"/" +LINECOMMENT "//".*\n %{ #include "dtc.h" @@ -52,29 +56,26 @@ static int dts_version; /* = 0 */ DPRINT("\n"); \ BEGIN(V1); \ } + +static void push_input_file(const char *filename); +static int pop_input_file(void); %} %% -<*>"/include/" BEGIN(INCLUDE); - -\"[^"\n]*\" { - yytext[strlen(yytext) - 1] = 0; - if (!push_input_file(yytext + 1)) { - /* Some unrecoverable error.*/ - exit(1); - } - BEGIN_DEFAULT(); +<*>"/include/"{WS}*{STRING} { + char *name = strchr(yytext, '\"') + 1; + yytext[yyleng-1] = '\0'; + push_input_file(name); } - <*><> { if (!pop_input_file()) { yyterminate(); } } -<*>\"([^\\"]|\\.)*\" { - yylloc.filenum = srcpos_filenum; +<*>{STRING} { + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("String: %s\n", yytext); yylval.data = data_copy_escape_string(yytext+1, @@ -84,7 +85,7 @@ static int dts_version; /* = 0 */ } <*>"/dts-v1/" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Keyword: /dts-v1/\n"); dts_version = 1; @@ -93,7 +94,7 @@ static int dts_version; /* = 0 */ } <*>"/memreserve/" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Keyword: /memreserve/\n"); BEGIN_DEFAULT(); @@ -101,7 +102,7 @@ static int dts_version; /* = 0 */ } <*>{LABEL}: { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Label: %s\n", yytext); yylval.labelref = strdup(yytext); @@ -110,7 +111,7 @@ static int dts_version; /* = 0 */ } [bodh]# { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; if (*yytext == 'b') yylval.cbase = 2; @@ -125,7 +126,7 @@ static int dts_version; /* = 0 */ } [0-9a-fA-F]+ { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; yylval.literal = strdup(yytext); DPRINT("Literal: '%s'\n", yylval.literal); @@ -133,7 +134,7 @@ static int dts_version; /* = 0 */ } [0-9]+|0[xX][0-9a-fA-F]+ { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; yylval.literal = strdup(yytext); DPRINT("Literal: '%s'\n", yylval.literal); @@ -141,7 +142,7 @@ static int dts_version; /* = 0 */ } \&{LABEL} { /* label reference */ - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Ref: %s\n", yytext+1); yylval.labelref = strdup(yytext+1); @@ -149,7 +150,7 @@ static int dts_version; /* = 0 */ } "&{/"{PATHCHAR}+\} { /* new-style path reference */ - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; yytext[yyleng-1] = '\0'; DPRINT("Ref: %s\n", yytext+2); @@ -158,7 +159,7 @@ static int dts_version; /* = 0 */ } "&/"{PATHCHAR}+ { /* old-style path reference */ - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Ref: %s\n", yytext+1); yylval.labelref = strdup(yytext+1); @@ -166,7 +167,7 @@ static int dts_version; /* = 0 */ } [0-9a-fA-F]{2} { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; yylval.byte = strtol(yytext, NULL, 16); DPRINT("Byte: %02x\n", (int)yylval.byte); @@ -174,7 +175,7 @@ static int dts_version; /* = 0 */ } "]" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("/BYTESTRING\n"); BEGIN_DEFAULT(); @@ -182,7 +183,7 @@ static int dts_version; /* = 0 */ } {PROPNODECHAR}+ { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("PropNodeName: %s\n", yytext); yylval.propnodename = strdup(yytext); @@ -190,20 +191,19 @@ static int dts_version; /* = 0 */ return DT_PROPNODENAME; } - -<*>[[:space:]]+ /* eat whitespace */ - -<*>"/*"([^*]|\*+[^*/])*\*+"/" { - yylloc.filenum = srcpos_filenum; +"/incbin/" { + yylloc.file = srcpos_file; yylloc.first_line = yylineno; - DPRINT("Comment: %s\n", yytext); - /* eat comments */ + DPRINT("Binary Include\n"); + return DT_INCBIN; } -<*>"//".*\n /* eat line comments */ +<*>{WS}+ /* eat whitespace */ +<*>{COMMENT}+ /* eat C-style comments */ +<*>{LINECOMMENT}+ /* eat C++-style comments */ <*>. { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Char: %c (\\x%02x)\n", yytext[0], (unsigned)yytext[0]); @@ -227,14 +227,13 @@ static int dts_version; /* = 0 */ */ struct incl_file { - int filenum; - FILE *file; + struct dtc_file *file; YY_BUFFER_STATE yy_prev_buf; int yy_prev_lineno; struct incl_file *prev; }; -struct incl_file *incl_file_stack; +static struct incl_file *incl_file_stack; /* @@ -245,36 +244,34 @@ struct incl_file *incl_file_stack; static int incl_depth = 0; -int push_input_file(const char *filename) +static void push_input_file(const char *filename) { - FILE *f; struct incl_file *incl_file; + struct dtc_file *newfile; + struct search_path search, *searchptr = NULL; - if (!filename) { - yyerror("No include file name given."); - return 0; - } + assert(filename); - if (incl_depth++ >= MAX_INCLUDE_DEPTH) { - yyerror("Includes nested too deeply"); - return 0; + if (incl_depth++ >= MAX_INCLUDE_DEPTH) + die("Includes nested too deeply"); + + if (srcpos_file) { + search.dir = srcpos_file->dir; + search.next = NULL; + search.prev = NULL; + searchptr = &search; } - f = dtc_open_file(filename); + newfile = dtc_open_file(filename, searchptr); - incl_file = malloc(sizeof(struct incl_file)); - if (!incl_file) { - yyerror("Can not allocate include file space."); - return 0; - } + incl_file = xmalloc(sizeof(struct incl_file)); /* * Save current context. */ incl_file->yy_prev_buf = YY_CURRENT_BUFFER; incl_file->yy_prev_lineno = yylineno; - incl_file->filenum = srcpos_filenum; - incl_file->file = yyin; + incl_file->file = srcpos_file; incl_file->prev = incl_file_stack; incl_file_stack = incl_file; @@ -282,23 +279,21 @@ int push_input_file(const char *filename) /* * Establish new context. */ - srcpos_filenum = lookup_file_name(filename, 0); + srcpos_file = newfile; yylineno = 1; - yyin = f; + yyin = newfile->file; yy_switch_to_buffer(yy_create_buffer(yyin, YY_BUF_SIZE)); - - return 1; } -int pop_input_file(void) +static int pop_input_file(void) { struct incl_file *incl_file; if (incl_file_stack == 0) return 0; - fclose(yyin); + dtc_close_file(srcpos_file); /* * Pop. @@ -313,16 +308,13 @@ int pop_input_file(void) yy_delete_buffer(YY_CURRENT_BUFFER); yy_switch_to_buffer(incl_file->yy_prev_buf); yylineno = incl_file->yy_prev_lineno; - srcpos_filenum = incl_file->filenum; - yyin = incl_file->file; + srcpos_file = incl_file->file; + yyin = incl_file->file ? incl_file->file->file : NULL; /* * Free old state. */ free(incl_file); - if (YY_CURRENT_BUFFER == 0) - return 0; - return 1; } diff --git a/arch/powerpc/boot/dtc-src/dtc-lexer.lex.c_shipped b/arch/powerpc/boot/dtc-src/dtc-lexer.lex.c_shipped index d0f742460f9..ac392cb040f 100644 --- a/arch/powerpc/boot/dtc-src/dtc-lexer.lex.c_shipped +++ b/arch/powerpc/boot/dtc-src/dtc-lexer.lex.c_shipped @@ -9,7 +9,7 @@ #define FLEX_SCANNER #define YY_FLEX_MAJOR_VERSION 2 #define YY_FLEX_MINOR_VERSION 5 -#define YY_FLEX_SUBMINOR_VERSION 33 +#define YY_FLEX_SUBMINOR_VERSION 34 #if YY_FLEX_SUBMINOR_VERSION > 0 #define FLEX_BETA #endif @@ -31,7 +31,7 @@ /* C99 systems have . Non-C99 systems may or may not. */ -#if __STDC_VERSION__ >= 199901L +#if defined (__STDC_VERSION__) && __STDC_VERSION__ >= 199901L /* C99 says to define __STDC_LIMIT_MACROS before including stdint.h, * if you want the limit (max/min) macros for int types. @@ -94,11 +94,12 @@ typedef unsigned int flex_uint32_t; #else /* ! __cplusplus */ -#if __STDC__ +/* C99 requires __STDC__ to be defined as 1. */ +#if defined (__STDC__) #define YY_USE_CONST -#endif /* __STDC__ */ +#endif /* defined (__STDC__) */ #endif /* ! __cplusplus */ #ifdef YY_USE_CONST @@ -194,11 +195,13 @@ extern FILE *yyin, *yyout; /* The following is because we cannot portably get our hands on size_t * (without autoconf's help, which isn't available because we want * flex-generated scanners to compile on their own). + * Given that the standard has decreed that size_t exists since 1989, + * I guess we can afford to depend on it. Manoj. */ #ifndef YY_TYPEDEF_YY_SIZE_T #define YY_TYPEDEF_YY_SIZE_T -typedef unsigned int yy_size_t; +typedef size_t yy_size_t; #endif #ifndef YY_STRUCT_YY_BUFFER_STATE @@ -349,7 +352,7 @@ void yyfree (void * ); /* Begin user sect3 */ -#define yywrap() 1 +#define yywrap(n) 1 #define YY_SKIP_YYWRAP typedef unsigned char YY_CHAR; @@ -389,19 +392,20 @@ struct yy_trans_info flex_int32_t yy_verify; flex_int32_t yy_nxt; }; -static yyconst flex_int16_t yy_accept[94] = +static yyconst flex_int16_t yy_accept[104] = { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, - 21, 19, 16, 16, 19, 19, 19, 8, 8, 19, - 8, 19, 19, 19, 19, 14, 15, 15, 19, 9, - 9, 16, 0, 3, 0, 0, 10, 0, 0, 0, - 0, 0, 0, 8, 8, 6, 0, 7, 0, 2, - 0, 13, 13, 15, 15, 9, 0, 12, 10, 0, - 0, 0, 0, 18, 0, 0, 0, 2, 9, 0, - 17, 0, 0, 0, 11, 0, 0, 0, 0, 0, - 0, 0, 0, 0, 4, 0, 0, 1, 0, 0, - 0, 5, 0 - + 21, 19, 16, 16, 19, 19, 19, 7, 7, 19, + 7, 19, 19, 19, 19, 13, 14, 14, 19, 8, + 8, 16, 0, 2, 0, 0, 9, 0, 0, 0, + 0, 0, 0, 7, 7, 5, 0, 6, 0, 12, + 12, 14, 14, 8, 0, 11, 9, 0, 0, 0, + 0, 18, 0, 0, 0, 0, 8, 0, 17, 0, + 0, 0, 0, 0, 10, 0, 0, 0, 0, 0, + 0, 0, 0, 0, 0, 0, 0, 0, 3, 15, + 0, 0, 0, 0, 0, 0, 0, 0, 1, 0, + + 0, 4, 0 } ; static yyconst flex_int32_t yy_ec[256] = @@ -444,122 +448,126 @@ static yyconst flex_int32_t yy_meta[36] = 7, 7, 7, 8, 1 } ; -static yyconst flex_int16_t yy_base[107] = +static yyconst flex_int16_t yy_base[117] = { 0, - 0, 0, 32, 0, 53, 0, 76, 0, 108, 111, - 280, 288, 37, 39, 33, 36, 106, 0, 123, 146, - 255, 251, 45, 0, 159, 288, 0, 53, 108, 172, - 114, 127, 158, 288, 245, 0, 0, 234, 235, 236, - 197, 195, 199, 0, 0, 288, 0, 288, 160, 288, - 183, 288, 0, 0, 183, 182, 0, 0, 0, 0, - 204, 189, 207, 288, 179, 187, 180, 194, 0, 171, - 288, 196, 178, 174, 288, 169, 169, 177, 165, 153, - 143, 155, 137, 118, 288, 122, 42, 288, 36, 36, - 40, 288, 288, 212, 218, 223, 229, 234, 239, 245, - - 251, 255, 262, 270, 275, 280 + 0, 0, 30, 0, 44, 0, 67, 0, 97, 105, + 302, 303, 35, 44, 40, 94, 112, 0, 129, 152, + 296, 295, 159, 0, 176, 303, 0, 116, 95, 165, + 49, 46, 102, 303, 296, 0, 0, 288, 290, 293, + 264, 266, 270, 0, 0, 303, 0, 303, 264, 303, + 0, 0, 195, 101, 0, 0, 0, 0, 284, 125, + 277, 265, 225, 230, 216, 218, 0, 202, 224, 221, + 217, 107, 196, 188, 303, 206, 179, 186, 178, 185, + 183, 162, 161, 150, 169, 160, 145, 125, 303, 303, + 137, 109, 190, 103, 203, 167, 108, 197, 303, 123, + + 29, 303, 303, 215, 221, 226, 229, 234, 240, 246, + 250, 257, 265, 270, 275, 282 } ; -static yyconst flex_int16_t yy_def[107] = +static yyconst flex_int16_t yy_def[117] = { 0, - 93, 1, 1, 3, 3, 5, 93, 7, 3, 3, - 93, 93, 93, 93, 94, 95, 93, 96, 93, 19, - 19, 20, 97, 98, 20, 93, 99, 100, 95, 93, - 93, 93, 94, 93, 94, 101, 102, 93, 103, 104, - 93, 93, 93, 96, 19, 93, 20, 93, 97, 93, - 97, 93, 20, 99, 100, 93, 105, 101, 102, 106, - 103, 103, 104, 93, 93, 93, 93, 94, 105, 106, - 93, 93, 93, 93, 93, 93, 93, 93, 93, 93, - 93, 93, 93, 93, 93, 93, 93, 93, 93, 93, - 93, 93, 0, 93, 93, 93, 93, 93, 93, 93, - - 93, 93, 93, 93, 93, 93 + 103, 1, 1, 3, 3, 5, 103, 7, 3, 3, + 103, 103, 103, 103, 104, 105, 103, 106, 103, 19, + 19, 20, 103, 107, 20, 103, 108, 109, 105, 103, + 103, 103, 104, 103, 104, 110, 111, 103, 112, 113, + 103, 103, 103, 106, 19, 103, 20, 103, 103, 103, + 20, 108, 109, 103, 114, 110, 111, 115, 112, 112, + 113, 103, 103, 103, 103, 103, 114, 115, 103, 103, + 103, 103, 103, 103, 103, 103, 103, 103, 103, 103, + 103, 103, 103, 103, 103, 103, 103, 103, 103, 103, + 103, 103, 103, 103, 103, 116, 103, 116, 103, 116, + + 103, 103, 0, 103, 103, 103, 103, 103, 103, 103, + 103, 103, 103, 103, 103, 103 } ; -static yyconst flex_int16_t yy_nxt[324] = +static yyconst flex_int16_t yy_nxt[339] = { 0, 12, 13, 14, 15, 12, 16, 12, 12, 12, 17, 18, 18, 18, 12, 19, 20, 20, 12, 12, 21, 19, 21, 19, 22, 20, 20, 20, 20, 20, 20, - 20, 20, 20, 12, 12, 23, 34, 12, 32, 32, - 32, 32, 12, 12, 12, 36, 20, 33, 50, 92, - 35, 20, 20, 20, 20, 20, 15, 54, 91, 54, - 54, 54, 51, 24, 24, 24, 46, 25, 90, 38, - 89, 26, 25, 25, 25, 25, 12, 13, 14, 15, - 27, 12, 27, 27, 27, 17, 27, 27, 27, 12, - 28, 28, 28, 12, 12, 28, 28, 28, 28, 28, - - 28, 28, 28, 28, 28, 28, 28, 28, 28, 12, - 12, 15, 39, 29, 15, 40, 29, 93, 30, 31, - 31, 30, 31, 31, 56, 56, 56, 41, 32, 32, - 42, 88, 43, 45, 45, 45, 46, 45, 47, 47, - 87, 38, 45, 45, 45, 45, 47, 47, 47, 47, - 47, 47, 47, 47, 47, 47, 47, 47, 47, 86, - 47, 34, 33, 50, 85, 47, 47, 47, 47, 53, - 53, 53, 84, 53, 83, 35, 82, 51, 53, 53, - 53, 53, 56, 56, 56, 93, 68, 54, 57, 54, - 54, 54, 56, 56, 56, 62, 46, 34, 71, 81, - - 80, 79, 78, 77, 76, 75, 74, 73, 72, 64, - 62, 35, 33, 33, 33, 33, 33, 33, 33, 33, - 37, 67, 66, 37, 37, 37, 44, 65, 44, 49, - 49, 49, 49, 49, 49, 49, 49, 52, 64, 52, - 54, 62, 54, 60, 54, 54, 55, 93, 55, 55, - 55, 55, 58, 58, 58, 48, 58, 58, 59, 48, - 59, 59, 61, 61, 61, 61, 61, 61, 61, 61, - 63, 63, 63, 63, 63, 63, 63, 63, 69, 93, - 69, 70, 70, 70, 93, 70, 70, 11, 93, 93, - 93, 93, 93, 93, 93, 93, 93, 93, 93, 93, - - 93, 93, 93, 93, 93, 93, 93, 93, 93, 93, - 93, 93, 93, 93, 93, 93, 93, 93, 93, 93, - 93, 93, 93 + 20, 20, 20, 12, 12, 12, 32, 32, 102, 23, + 12, 12, 12, 34, 20, 32, 32, 32, 32, 20, + 20, 20, 20, 20, 24, 24, 24, 35, 25, 54, + 54, 54, 26, 25, 25, 25, 25, 12, 13, 14, + 15, 27, 12, 27, 27, 27, 23, 27, 27, 27, + 12, 28, 28, 28, 12, 12, 28, 28, 28, 28, + 28, 28, 28, 28, 28, 28, 28, 28, 28, 28, + + 12, 12, 29, 36, 103, 34, 17, 30, 31, 31, + 29, 54, 54, 54, 17, 30, 31, 31, 39, 35, + 52, 40, 52, 52, 52, 103, 78, 38, 38, 46, + 101, 60, 79, 41, 69, 97, 42, 94, 43, 45, + 45, 45, 46, 45, 47, 47, 93, 92, 45, 45, + 45, 45, 47, 47, 47, 47, 47, 47, 47, 47, + 47, 47, 47, 47, 47, 39, 47, 91, 40, 90, + 99, 47, 47, 47, 47, 54, 54, 54, 89, 88, + 41, 55, 87, 49, 100, 43, 51, 51, 51, 86, + 51, 95, 95, 96, 85, 51, 51, 51, 51, 52, + + 99, 52, 52, 52, 95, 95, 96, 84, 46, 83, + 82, 81, 39, 79, 100, 33, 33, 33, 33, 33, + 33, 33, 33, 37, 80, 77, 37, 37, 37, 44, + 40, 44, 50, 76, 50, 52, 75, 52, 74, 52, + 52, 53, 73, 53, 53, 53, 53, 56, 56, 56, + 72, 56, 56, 57, 71, 57, 57, 59, 59, 59, + 59, 59, 59, 59, 59, 61, 61, 61, 61, 61, + 61, 61, 61, 67, 70, 67, 68, 68, 68, 62, + 68, 68, 98, 98, 98, 98, 98, 98, 98, 98, + 60, 66, 65, 64, 63, 62, 60, 58, 103, 48, + + 48, 103, 11, 103, 103, 103, 103, 103, 103, 103, + 103, 103, 103, 103, 103, 103, 103, 103, 103, 103, + 103, 103, 103, 103, 103, 103, 103, 103, 103, 103, + 103, 103, 103, 103, 103, 103, 103, 103 } ; -static yyconst flex_int16_t yy_chk[324] = +static yyconst flex_int16_t yy_chk[339] = { 0, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, - 1, 1, 1, 1, 1, 3, 15, 3, 13, 13, - 14, 14, 3, 3, 3, 16, 3, 23, 23, 91, - 15, 3, 3, 3, 3, 3, 5, 28, 90, 28, - 28, 28, 23, 5, 5, 5, 28, 5, 89, 16, - 87, 5, 5, 5, 5, 5, 7, 7, 7, 7, + 1, 1, 1, 1, 1, 3, 13, 13, 101, 3, + 3, 3, 3, 15, 3, 14, 14, 32, 32, 3, + 3, 3, 3, 3, 5, 5, 5, 15, 5, 31, + 31, 31, 5, 5, 5, 5, 5, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, - 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, - 7, 9, 17, 9, 10, 17, 10, 29, 9, 9, - 9, 10, 10, 10, 31, 31, 31, 17, 32, 32, - 17, 86, 17, 19, 19, 19, 19, 19, 19, 19, - 84, 29, 19, 19, 19, 19, 19, 19, 19, 19, - 19, 19, 19, 19, 19, 19, 20, 20, 20, 83, - 20, 33, 49, 49, 82, 20, 20, 20, 20, 25, - 25, 25, 81, 25, 80, 33, 79, 49, 25, 25, - 25, 25, 30, 30, 30, 51, 51, 55, 30, 55, - 55, 55, 56, 56, 56, 62, 55, 68, 62, 78, - - 77, 76, 74, 73, 72, 70, 67, 66, 65, 63, - 61, 68, 94, 94, 94, 94, 94, 94, 94, 94, - 95, 43, 42, 95, 95, 95, 96, 41, 96, 97, - 97, 97, 97, 97, 97, 97, 97, 98, 40, 98, - 99, 39, 99, 38, 99, 99, 100, 35, 100, 100, - 100, 100, 101, 101, 101, 22, 101, 101, 102, 21, - 102, 102, 103, 103, 103, 103, 103, 103, 103, 103, - 104, 104, 104, 104, 104, 104, 104, 104, 105, 11, - 105, 106, 106, 106, 0, 106, 106, 93, 93, 93, - 93, 93, 93, 93, 93, 93, 93, 93, 93, 93, - - 93, 93, 93, 93, 93, 93, 93, 93, 93, 93, - 93, 93, 93, 93, 93, 93, 93, 93, 93, 93, - 93, 93, 93 + + 7, 7, 9, 16, 29, 33, 9, 9, 9, 9, + 10, 54, 54, 54, 10, 10, 10, 10, 17, 33, + 28, 17, 28, 28, 28, 100, 72, 16, 29, 28, + 97, 60, 72, 17, 60, 94, 17, 92, 17, 19, + 19, 19, 19, 19, 19, 19, 91, 88, 19, 19, + 19, 19, 19, 19, 19, 19, 19, 19, 19, 19, + 19, 19, 20, 20, 20, 23, 20, 87, 23, 86, + 96, 20, 20, 20, 20, 30, 30, 30, 85, 84, + 23, 30, 83, 23, 96, 23, 25, 25, 25, 82, + 25, 93, 93, 93, 81, 25, 25, 25, 25, 53, + + 98, 53, 53, 53, 95, 95, 95, 80, 53, 79, + 78, 77, 76, 74, 98, 104, 104, 104, 104, 104, + 104, 104, 104, 105, 73, 71, 105, 105, 105, 106, + 70, 106, 107, 69, 107, 108, 68, 108, 66, 108, + 108, 109, 65, 109, 109, 109, 109, 110, 110, 110, + 64, 110, 110, 111, 63, 111, 111, 112, 112, 112, + 112, 112, 112, 112, 112, 113, 113, 113, 113, 113, + 113, 113, 113, 114, 62, 114, 115, 115, 115, 61, + 115, 115, 116, 116, 116, 116, 116, 116, 116, 116, + 59, 49, 43, 42, 41, 40, 39, 38, 35, 22, + + 21, 11, 103, 103, 103, 103, 103, 103, 103, 103, + 103, 103, 103, 103, 103, 103, 103, 103, 103, 103, + 103, 103, 103, 103, 103, 103, 103, 103, 103, 103, + 103, 103, 103, 103, 103, 103, 103, 103 } ; /* Table of booleans, true if rule could match eol. */ static yyconst flex_int32_t yy_rule_can_match_eol[21] = { 0, -0, 0, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 0, +1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 0, 0, }; static yy_state_type yy_last_accepting_state; @@ -600,7 +608,7 @@ char *yytext; -#line 33 "dtc-lexer.l" +#line 37 "dtc-lexer.l" #include "dtc.h" #include "srcpos.h" #include "dtc-parser.tab.h" @@ -623,7 +631,10 @@ static int dts_version; /* = 0 */ DPRINT("\n"); \ BEGIN(V1); \ } -#line 627 "dtc-lexer.lex.c" + +static void push_input_file(const char *filename); +static int pop_input_file(void); +#line 638 "dtc-lexer.lex.c" #define INITIAL 0 #define INCLUDE 1 @@ -685,7 +696,7 @@ static int input (void ); /* This used to be an fputs(), but since the string might contain NUL's, * we now use fwrite(). */ -#define ECHO (void) fwrite( yytext, yyleng, 1, yyout ) +#define ECHO fwrite( yytext, yyleng, 1, yyout ) #endif /* Gets input and stuffs it into "buf". number of characters read, or YY_NULL, @@ -696,7 +707,7 @@ static int input (void ); if ( YY_CURRENT_BUFFER_LVALUE->yy_is_interactive ) \ { \ int c = '*'; \ - size_t n; \ + int n; \ for ( n = 0; n < max_size && \ (c = getc( yyin )) != EOF && c != '\n'; ++n ) \ buf[n] = (char) c; \ @@ -778,9 +789,9 @@ YY_DECL register char *yy_cp, *yy_bp; register int yy_act; -#line 57 "dtc-lexer.l" +#line 64 "dtc-lexer.l" -#line 784 "dtc-lexer.lex.c" +#line 795 "dtc-lexer.lex.c" if ( !(yy_init) ) { @@ -833,13 +844,13 @@ yy_match: while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state ) { yy_current_state = (int) yy_def[yy_current_state]; - if ( yy_current_state >= 94 ) + if ( yy_current_state >= 104 ) yy_c = yy_meta[(unsigned int) yy_c]; } yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c]; ++yy_cp; } - while ( yy_base[yy_current_state] != 288 ); + while ( yy_base[yy_current_state] != 303 ); yy_find_action: yy_act = yy_accept[yy_current_state]; @@ -874,20 +885,13 @@ do_action: /* This label is used only to access EOF actions. */ goto yy_find_action; case 1: +/* rule 1 can match eol */ YY_RULE_SETUP -#line 58 "dtc-lexer.l" -BEGIN(INCLUDE); - YY_BREAK -case 2: -YY_RULE_SETUP -#line 60 "dtc-lexer.l" +#line 65 "dtc-lexer.l" { - yytext[strlen(yytext) - 1] = 0; - if (!push_input_file(yytext + 1)) { - /* Some unrecoverable error.*/ - exit(1); - } - BEGIN_DEFAULT(); + char *name = strchr(yytext, '\"') + 1; + yytext[yyleng-1] = '\0'; + push_input_file(name); } YY_BREAK case YY_STATE_EOF(INITIAL): @@ -895,19 +899,19 @@ case YY_STATE_EOF(INCLUDE): case YY_STATE_EOF(BYTESTRING): case YY_STATE_EOF(PROPNODENAME): case YY_STATE_EOF(V1): -#line 70 "dtc-lexer.l" +#line 71 "dtc-lexer.l" { if (!pop_input_file()) { yyterminate(); } } YY_BREAK -case 3: -/* rule 3 can match eol */ +case 2: +/* rule 2 can match eol */ YY_RULE_SETUP -#line 76 "dtc-lexer.l" +#line 77 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("String: %s\n", yytext); yylval.data = data_copy_escape_string(yytext+1, @@ -916,11 +920,11 @@ YY_RULE_SETUP return DT_STRING; } YY_BREAK -case 4: +case 3: YY_RULE_SETUP -#line 86 "dtc-lexer.l" +#line 87 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Keyword: /dts-v1/\n"); dts_version = 1; @@ -928,22 +932,22 @@ YY_RULE_SETUP return DT_V1; } YY_BREAK -case 5: +case 4: YY_RULE_SETUP -#line 95 "dtc-lexer.l" +#line 96 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Keyword: /memreserve/\n"); BEGIN_DEFAULT(); return DT_MEMRESERVE; } YY_BREAK -case 6: +case 5: YY_RULE_SETUP -#line 103 "dtc-lexer.l" +#line 104 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Label: %s\n", yytext); yylval.labelref = strdup(yytext); @@ -951,11 +955,11 @@ YY_RULE_SETUP return DT_LABEL; } YY_BREAK -case 7: +case 6: YY_RULE_SETUP -#line 112 "dtc-lexer.l" +#line 113 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; if (*yytext == 'b') yylval.cbase = 2; @@ -969,44 +973,44 @@ YY_RULE_SETUP return DT_BASE; } YY_BREAK -case 8: +case 7: YY_RULE_SETUP -#line 127 "dtc-lexer.l" +#line 128 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; yylval.literal = strdup(yytext); DPRINT("Literal: '%s'\n", yylval.literal); return DT_LEGACYLITERAL; } YY_BREAK -case 9: +case 8: YY_RULE_SETUP -#line 135 "dtc-lexer.l" +#line 136 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; yylval.literal = strdup(yytext); DPRINT("Literal: '%s'\n", yylval.literal); return DT_LITERAL; } YY_BREAK -case 10: +case 9: YY_RULE_SETUP -#line 143 "dtc-lexer.l" +#line 144 "dtc-lexer.l" { /* label reference */ - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Ref: %s\n", yytext+1); yylval.labelref = strdup(yytext+1); return DT_REF; } YY_BREAK -case 11: +case 10: YY_RULE_SETUP -#line 151 "dtc-lexer.l" +#line 152 "dtc-lexer.l" { /* new-style path reference */ - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; yytext[yyleng-1] = '\0'; DPRINT("Ref: %s\n", yytext+2); @@ -1014,44 +1018,44 @@ YY_RULE_SETUP return DT_REF; } YY_BREAK -case 12: +case 11: YY_RULE_SETUP -#line 160 "dtc-lexer.l" +#line 161 "dtc-lexer.l" { /* old-style path reference */ - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Ref: %s\n", yytext+1); yylval.labelref = strdup(yytext+1); return DT_REF; } YY_BREAK -case 13: +case 12: YY_RULE_SETUP -#line 168 "dtc-lexer.l" +#line 169 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; yylval.byte = strtol(yytext, NULL, 16); DPRINT("Byte: %02x\n", (int)yylval.byte); return DT_BYTE; } YY_BREAK -case 14: +case 13: YY_RULE_SETUP -#line 176 "dtc-lexer.l" +#line 177 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("/BYTESTRING\n"); BEGIN_DEFAULT(); return ']'; } YY_BREAK -case 15: +case 14: YY_RULE_SETUP -#line 184 "dtc-lexer.l" +#line 185 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("PropNodeName: %s\n", yytext); yylval.propnodename = strdup(yytext); @@ -1059,34 +1063,39 @@ YY_RULE_SETUP return DT_PROPNODENAME; } YY_BREAK +case 15: +YY_RULE_SETUP +#line 194 "dtc-lexer.l" +{ + yylloc.file = srcpos_file; + yylloc.first_line = yylineno; + DPRINT("Binary Include\n"); + return DT_INCBIN; + } + YY_BREAK case 16: /* rule 16 can match eol */ YY_RULE_SETUP -#line 194 "dtc-lexer.l" +#line 201 "dtc-lexer.l" /* eat whitespace */ YY_BREAK case 17: /* rule 17 can match eol */ YY_RULE_SETUP -#line 196 "dtc-lexer.l" -{ - yylloc.filenum = srcpos_filenum; - yylloc.first_line = yylineno; - DPRINT("Comment: %s\n", yytext); - /* eat comments */ - } +#line 202 "dtc-lexer.l" +/* eat C-style comments */ YY_BREAK case 18: /* rule 18 can match eol */ YY_RULE_SETUP #line 203 "dtc-lexer.l" -/* eat line comments */ +/* eat C++-style comments */ YY_BREAK case 19: YY_RULE_SETUP #line 205 "dtc-lexer.l" { - yylloc.filenum = srcpos_filenum; + yylloc.file = srcpos_file; yylloc.first_line = yylineno; DPRINT("Char: %c (\\x%02x)\n", yytext[0], (unsigned)yytext[0]); @@ -1107,7 +1116,7 @@ YY_RULE_SETUP #line 222 "dtc-lexer.l" ECHO; YY_BREAK -#line 1111 "dtc-lexer.lex.c" +#line 1120 "dtc-lexer.lex.c" case YY_END_OF_BUFFER: { @@ -1360,6 +1369,14 @@ static int yy_get_next_buffer (void) else ret_val = EOB_ACT_CONTINUE_SCAN; + if ((yy_size_t) ((yy_n_chars) + number_to_move) > YY_CURRENT_BUFFER_LVALUE->yy_buf_size) { + /* Extend the array by 50%, plus the number we really need. */ + yy_size_t new_size = (yy_n_chars) + number_to_move + ((yy_n_chars) >> 1); + YY_CURRENT_BUFFER_LVALUE->yy_ch_buf = (char *) yyrealloc((void *) YY_CURRENT_BUFFER_LVALUE->yy_ch_buf,new_size ); + if ( ! YY_CURRENT_BUFFER_LVALUE->yy_ch_buf ) + YY_FATAL_ERROR( "out of dynamic memory in yy_get_next_buffer()" ); + } + (yy_n_chars) += number_to_move; YY_CURRENT_BUFFER_LVALUE->yy_ch_buf[(yy_n_chars)] = YY_END_OF_BUFFER_CHAR; YY_CURRENT_BUFFER_LVALUE->yy_ch_buf[(yy_n_chars) + 1] = YY_END_OF_BUFFER_CHAR; @@ -1389,7 +1406,7 @@ static int yy_get_next_buffer (void) while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state ) { yy_current_state = (int) yy_def[yy_current_state]; - if ( yy_current_state >= 94 ) + if ( yy_current_state >= 104 ) yy_c = yy_meta[(unsigned int) yy_c]; } yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c]; @@ -1417,11 +1434,11 @@ static int yy_get_next_buffer (void) while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state ) { yy_current_state = (int) yy_def[yy_current_state]; - if ( yy_current_state >= 94 ) + if ( yy_current_state >= 104 ) yy_c = yy_meta[(unsigned int) yy_c]; } yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c]; - yy_is_jam = (yy_current_state == 93); + yy_is_jam = (yy_current_state == 103); return yy_is_jam ? 0 : yy_current_state; } @@ -1743,7 +1760,9 @@ static void yyensure_buffer_stack (void) (yy_buffer_stack) = (struct yy_buffer_state**)yyalloc (num_to_alloc * sizeof(struct yy_buffer_state*) ); - + if ( ! (yy_buffer_stack) ) + YY_FATAL_ERROR( "out of dynamic memory in yyensure_buffer_stack()" ); + memset((yy_buffer_stack), 0, num_to_alloc * sizeof(struct yy_buffer_state*)); (yy_buffer_stack_max) = num_to_alloc; @@ -1761,6 +1780,8 @@ static void yyensure_buffer_stack (void) ((yy_buffer_stack), num_to_alloc * sizeof(struct yy_buffer_state*) ); + if ( ! (yy_buffer_stack) ) + YY_FATAL_ERROR( "out of dynamic memory in yyensure_buffer_stack()" ); /* zero only the new slots.*/ memset((yy_buffer_stack) + (yy_buffer_stack_max), 0, grow_size * sizeof(struct yy_buffer_state*)); @@ -2072,14 +2093,13 @@ void yyfree (void * ptr ) */ struct incl_file { - int filenum; - FILE *file; + struct dtc_file *file; YY_BUFFER_STATE yy_prev_buf; int yy_prev_lineno; struct incl_file *prev; }; -struct incl_file *incl_file_stack; +static struct incl_file *incl_file_stack; /* @@ -2090,36 +2110,34 @@ struct incl_file *incl_file_stack; static int incl_depth = 0; -int push_input_file(const char *filename) +static void push_input_file(const char *filename) { - FILE *f; struct incl_file *incl_file; + struct dtc_file *newfile; + struct search_path search, *searchptr = NULL; - if (!filename) { - yyerror("No include file name given."); - return 0; - } + assert(filename); - if (incl_depth++ >= MAX_INCLUDE_DEPTH) { - yyerror("Includes nested too deeply"); - return 0; + if (incl_depth++ >= MAX_INCLUDE_DEPTH) + die("Includes nested too deeply"); + + if (srcpos_file) { + search.dir = srcpos_file->dir; + search.next = NULL; + search.prev = NULL; + searchptr = &search; } - f = dtc_open_file(filename); + newfile = dtc_open_file(filename, searchptr); - incl_file = malloc(sizeof(struct incl_file)); - if (!incl_file) { - yyerror("Can not allocate include file space."); - return 0; - } + incl_file = xmalloc(sizeof(struct incl_file)); /* * Save current context. */ incl_file->yy_prev_buf = YY_CURRENT_BUFFER; incl_file->yy_prev_lineno = yylineno; - incl_file->filenum = srcpos_filenum; - incl_file->file = yyin; + incl_file->file = srcpos_file; incl_file->prev = incl_file_stack; incl_file_stack = incl_file; @@ -2127,23 +2145,21 @@ int push_input_file(const char *filename) /* * Establish new context. */ - srcpos_filenum = lookup_file_name(filename, 0); + srcpos_file = newfile; yylineno = 1; - yyin = f; + yyin = newfile->file; yy_switch_to_buffer(yy_create_buffer(yyin,YY_BUF_SIZE)); - - return 1; } -int pop_input_file(void) +static int pop_input_file(void) { struct incl_file *incl_file; if (incl_file_stack == 0) return 0; - fclose(yyin); + dtc_close_file(srcpos_file); /* * Pop. @@ -2158,17 +2174,14 @@ int pop_input_file(void) yy_delete_buffer(YY_CURRENT_BUFFER); yy_switch_to_buffer(incl_file->yy_prev_buf); yylineno = incl_file->yy_prev_lineno; - srcpos_filenum = incl_file->filenum; - yyin = incl_file->file; + srcpos_file = incl_file->file; + yyin = incl_file->file ? incl_file->file->file : NULL; /* * Free old state. */ free(incl_file); - if (YY_CURRENT_BUFFER == 0) - return 0; - return 1; } diff --git a/arch/powerpc/boot/dtc-src/dtc-parser.tab.c_shipped b/arch/powerpc/boot/dtc-src/dtc-parser.tab.c_shipped index 28e6ec0296a..27129377e5d 100644 --- a/arch/powerpc/boot/dtc-src/dtc-parser.tab.c_shipped +++ b/arch/powerpc/boot/dtc-src/dtc-parser.tab.c_shipped @@ -75,7 +75,8 @@ DT_BYTE = 264, DT_STRING = 265, DT_LABEL = 266, - DT_REF = 267 + DT_REF = 267, + DT_INCBIN = 268 }; #endif /* Tokens. */ @@ -89,6 +90,7 @@ #define DT_STRING 265 #define DT_LABEL 266 #define DT_REF 267 +#define DT_INCBIN 268 @@ -96,14 +98,17 @@ /* Copy the first part of user declarations. */ #line 23 "dtc-parser.y" +#include + #include "dtc.h" #include "srcpos.h" -int yylex(void); -unsigned long long eval_literal(const char *s, int base, int bits); +extern int yylex(void); extern struct boot_info *the_boot_info; +extern int treesource_error; +static unsigned long long eval_literal(const char *s, int base, int bits); /* Enabling traces. */ @@ -126,16 +131,16 @@ extern struct boot_info *the_boot_info; #if ! defined YYSTYPE && ! defined YYSTYPE_IS_DECLARED typedef union YYSTYPE -#line 34 "dtc-parser.y" +#line 37 "dtc-parser.y" { char *propnodename; char *literal; char *labelref; unsigned int cbase; - u8 byte; + uint8_t byte; struct data data; - u64 addr; + uint64_t addr; cell_t cell; struct property *prop; struct property *proplist; @@ -144,7 +149,7 @@ typedef union YYSTYPE struct reserve_info *re; } /* Line 187 of yacc.c. */ -#line 148 "dtc-parser.tab.c" +#line 153 "dtc-parser.tab.c" YYSTYPE; # define yystype YYSTYPE /* obsolescent; will be withdrawn */ # define YYSTYPE_IS_DECLARED 1 @@ -169,7 +174,7 @@ typedef struct YYLTYPE /* Line 216 of yacc.c. */ -#line 173 "dtc-parser.tab.c" +#line 178 "dtc-parser.tab.c" #ifdef short # undef short @@ -386,20 +391,20 @@ union yyalloc /* YYFINAL -- State number of the termination state. */ #define YYFINAL 9 /* YYLAST -- Last index in YYTABLE. */ -#define YYLAST 60 +#define YYLAST 73 /* YYNTOKENS -- Number of terminals. */ -#define YYNTOKENS 24 +#define YYNTOKENS 27 /* YYNNTS -- Number of nonterminals. */ #define YYNNTS 20 /* YYNRULES -- Number of rules. */ -#define YYNRULES 43 +#define YYNRULES 45 /* YYNRULES -- Number of states. */ -#define YYNSTATES 67 +#define YYNSTATES 76 /* YYTRANSLATE(YYLEX) -- Bison symbol number corresponding to YYLEX. */ #define YYUNDEFTOK 2 -#define YYMAXUTOK 267 +#define YYMAXUTOK 268 #define YYTRANSLATE(YYX) \ ((unsigned int) (YYX) <= YYMAXUTOK ? yytranslate[YYX] : YYUNDEFTOK) @@ -411,15 +416,15 @@ static const yytype_uint8 yytranslate[] = 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, - 2, 2, 2, 2, 23, 14, 2, 15, 2, 2, - 2, 2, 2, 2, 2, 2, 2, 2, 2, 13, - 19, 18, 20, 2, 2, 2, 2, 2, 2, 2, + 24, 26, 2, 2, 25, 15, 2, 16, 2, 2, + 2, 2, 2, 2, 2, 2, 2, 2, 2, 14, + 20, 19, 21, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, - 2, 21, 2, 22, 2, 2, 2, 2, 2, 2, + 2, 22, 2, 23, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, - 2, 2, 2, 16, 2, 17, 2, 2, 2, 2, + 2, 2, 2, 17, 2, 18, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, @@ -433,7 +438,7 @@ static const yytype_uint8 yytranslate[] = 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 1, 2, 3, 4, - 5, 6, 7, 8, 9, 10, 11, 12 + 5, 6, 7, 8, 9, 10, 11, 12, 13 }; #if YYDEBUG @@ -443,37 +448,39 @@ static const yytype_uint8 yyprhs[] = { 0, 0, 3, 8, 11, 12, 15, 21, 22, 25, 27, 34, 36, 38, 41, 47, 48, 51, 57, 61, - 64, 69, 74, 77, 80, 81, 84, 87, 88, 91, - 94, 97, 98, 100, 102, 105, 106, 109, 112, 113, - 116, 119, 123, 124 + 64, 69, 74, 77, 87, 93, 96, 97, 100, 103, + 104, 107, 110, 113, 114, 116, 118, 121, 122, 125, + 128, 129, 132, 135, 139, 140 }; /* YYRHS -- A `-1'-separated list of the rules' RHS. */ static const yytype_int8 yyrhs[] = { - 25, 0, -1, 3, 13, 26, 31, -1, 28, 31, - -1, -1, 27, 26, -1, 43, 4, 30, 30, 13, - -1, -1, 29, 28, -1, 27, -1, 43, 4, 30, - 14, 30, 13, -1, 6, -1, 7, -1, 15, 32, - -1, 16, 33, 41, 17, 13, -1, -1, 33, 34, - -1, 43, 5, 18, 35, 13, -1, 43, 5, 13, - -1, 36, 10, -1, 36, 19, 37, 20, -1, 36, - 21, 40, 22, -1, 36, 12, -1, 35, 11, -1, - -1, 35, 23, -1, 36, 11, -1, -1, 37, 39, - -1, 37, 12, -1, 37, 11, -1, -1, 8, -1, - 6, -1, 38, 7, -1, -1, 40, 9, -1, 40, - 11, -1, -1, 42, 41, -1, 42, 34, -1, 43, - 5, 32, -1, -1, 11, -1 + 28, 0, -1, 3, 14, 29, 34, -1, 31, 34, + -1, -1, 30, 29, -1, 46, 4, 33, 33, 14, + -1, -1, 32, 31, -1, 30, -1, 46, 4, 33, + 15, 33, 14, -1, 6, -1, 7, -1, 16, 35, + -1, 17, 36, 44, 18, 14, -1, -1, 36, 37, + -1, 46, 5, 19, 38, 14, -1, 46, 5, 14, + -1, 39, 10, -1, 39, 20, 40, 21, -1, 39, + 22, 43, 23, -1, 39, 12, -1, 39, 13, 24, + 10, 25, 33, 25, 33, 26, -1, 39, 13, 24, + 10, 26, -1, 38, 11, -1, -1, 38, 25, -1, + 39, 11, -1, -1, 40, 42, -1, 40, 12, -1, + 40, 11, -1, -1, 8, -1, 6, -1, 41, 7, + -1, -1, 43, 9, -1, 43, 11, -1, -1, 45, + 44, -1, 45, 37, -1, 46, 5, 35, -1, -1, + 11, -1 }; /* YYRLINE[YYN] -- source line where rule number YYN was defined. */ static const yytype_uint16 yyrline[] = { - 0, 85, 85, 89, 97, 100, 107, 115, 118, 125, - 129, 136, 140, 147, 154, 162, 165, 172, 176, 183, - 187, 191, 195, 199, 207, 210, 214, 222, 225, 229, - 234, 242, 245, 249, 253, 261, 264, 268, 276, 279, - 283, 291, 299, 302 + 0, 89, 89, 93, 101, 104, 111, 119, 122, 129, + 133, 140, 144, 151, 158, 166, 169, 176, 180, 187, + 191, 195, 199, 203, 220, 231, 239, 242, 246, 254, + 257, 261, 266, 274, 277, 281, 285, 293, 296, 300, + 308, 311, 315, 323, 331, 334 }; #endif @@ -484,12 +491,12 @@ static const char *const yytname[] = { "$end", "error", "$undefined", "DT_V1", "DT_MEMRESERVE", "DT_PROPNODENAME", "DT_LITERAL", "DT_LEGACYLITERAL", "DT_BASE", - "DT_BYTE", "DT_STRING", "DT_LABEL", "DT_REF", "';'", "'-'", "'/'", "'{'", - "'}'", "'='", "'<'", "'>'", "'['", "']'", "','", "$accept", "sourcefile", - "memreserves", "memreserve", "v0_memreserves", "v0_memreserve", "addr", - "devicetree", "nodedef", "proplist", "propdef", "propdata", - "propdataprefix", "celllist", "cellbase", "cellval", "bytestring", - "subnodes", "subnode", "label", 0 + "DT_BYTE", "DT_STRING", "DT_LABEL", "DT_REF", "DT_INCBIN", "';'", "'-'", + "'/'", "'{'", "'}'", "'='", "'<'", "'>'", "'['", "']'", "'('", "','", + "')'", "$accept", "sourcefile", "memreserves", "memreserve", + "v0_memreserves", "v0_memreserve", "addr", "devicetree", "nodedef", + "proplist", "propdef", "propdata", "propdataprefix", "celllist", + "cellbase", "cellval", "bytestring", "subnodes", "subnode", "label", 0 }; #endif @@ -499,19 +506,19 @@ static const char *const yytname[] = static const yytype_uint16 yytoknum[] = { 0, 256, 257, 258, 259, 260, 261, 262, 263, 264, - 265, 266, 267, 59, 45, 47, 123, 125, 61, 60, - 62, 91, 93, 44 + 265, 266, 267, 268, 59, 45, 47, 123, 125, 61, + 60, 62, 91, 93, 40, 44, 41 }; # endif /* YYR1[YYN] -- Symbol number of symbol that rule YYN derives. */ static const yytype_uint8 yyr1[] = { - 0, 24, 25, 25, 26, 26, 27, 28, 28, 29, - 29, 30, 30, 31, 32, 33, 33, 34, 34, 35, - 35, 35, 35, 35, 36, 36, 36, 37, 37, 37, - 37, 38, 38, 39, 39, 40, 40, 40, 41, 41, - 41, 42, 43, 43 + 0, 27, 28, 28, 29, 29, 30, 31, 31, 32, + 32, 33, 33, 34, 35, 36, 36, 37, 37, 38, + 38, 38, 38, 38, 38, 38, 39, 39, 39, 40, + 40, 40, 40, 41, 41, 42, 42, 43, 43, 43, + 44, 44, 44, 45, 46, 46 }; /* YYR2[YYN] -- Number of symbols composing right hand side of rule YYN. */ @@ -519,9 +526,9 @@ static const yytype_uint8 yyr2[] = { 0, 2, 4, 2, 0, 2, 5, 0, 2, 1, 6, 1, 1, 2, 5, 0, 2, 5, 3, 2, - 4, 4, 2, 2, 0, 2, 2, 0, 2, 2, - 2, 0, 1, 1, 2, 0, 2, 2, 0, 2, - 2, 3, 0, 1 + 4, 4, 2, 9, 5, 2, 0, 2, 2, 0, + 2, 2, 2, 0, 1, 1, 2, 0, 2, 2, + 0, 2, 2, 3, 0, 1 }; /* YYDEFACT[STATE-NAME] -- Default rule to reduce with in state @@ -529,81 +536,86 @@ static const yytype_uint8 yyr2[] = means the default is an error. */ static const yytype_uint8 yydefact[] = { - 7, 0, 43, 0, 9, 0, 7, 0, 4, 1, + 7, 0, 45, 0, 9, 0, 7, 0, 4, 1, 0, 3, 8, 0, 0, 4, 0, 15, 13, 11, - 12, 0, 2, 5, 0, 38, 0, 0, 0, 16, - 0, 38, 0, 0, 6, 0, 40, 39, 0, 10, - 14, 18, 24, 41, 0, 0, 23, 17, 25, 19, - 26, 22, 27, 35, 31, 0, 33, 32, 30, 29, - 20, 0, 28, 36, 37, 21, 34 + 12, 0, 2, 5, 0, 40, 0, 0, 0, 16, + 0, 40, 0, 0, 6, 0, 42, 41, 0, 10, + 14, 18, 26, 43, 0, 0, 25, 17, 27, 19, + 28, 22, 0, 29, 37, 0, 33, 0, 0, 35, + 34, 32, 31, 20, 0, 30, 38, 39, 21, 0, + 24, 36, 0, 0, 0, 23 }; /* YYDEFGOTO[NTERM-NUM]. */ static const yytype_int8 yydefgoto[] = { -1, 3, 14, 4, 5, 6, 27, 11, 18, 25, - 29, 44, 45, 54, 61, 62, 55, 30, 31, 7 + 29, 44, 45, 56, 64, 65, 57, 30, 31, 7 }; /* YYPACT[STATE-NUM] -- Index in YYTABLE of the portion describing STATE-NUM. */ -#define YYPACT_NINF -13 +#define YYPACT_NINF -14 static const yytype_int8 yypact[] = { - 23, 11, -13, 37, -13, -4, 18, 39, 18, -13, - 28, -13, -13, 34, -4, 18, 41, -13, -13, -13, - -13, 25, -13, -13, 34, -3, 34, 33, 34, -13, - 30, -3, 43, 36, -13, 38, -13, -13, 20, -13, - -13, -13, -13, -13, 2, 9, -13, -13, -13, -13, - -13, -13, -13, -13, -2, -6, -13, -13, -13, -13, - -13, 45, -13, -13, -13, -13, -13 + 30, -11, -14, 7, -14, -1, 27, 13, 27, -14, + 8, -14, -14, 40, -1, 27, 35, -14, -14, -14, + -14, 21, -14, -14, 40, 24, 40, 28, 40, -14, + 32, 24, 46, 38, -14, 39, -14, -14, 26, -14, + -14, -14, -14, -14, -9, 10, -14, -14, -14, -14, + -14, -14, 31, -14, -14, 44, -2, 3, 23, -14, + -14, -14, -14, -14, 50, -14, -14, -14, -14, 40, + -14, -14, 33, 40, 36, -14 }; /* YYPGOTO[NTERM-NUM]. */ static const yytype_int8 yypgoto[] = { - -13, -13, 35, 27, 47, -13, -12, 40, 17, -13, - 26, -13, -13, -13, -13, -13, -13, 29, -13, -8 + -14, -14, 48, 29, 53, -14, -13, 47, 34, -14, + 37, -14, -14, -14, -14, -14, -14, 42, -14, -7 }; /* YYTABLE[YYPACT[STATE-NUM]]. What to do in state STATE-NUM. If positive, shift that token. If negative, reduce the rule which number is the opposite. If zero, do what YYDEFACT says. If YYTABLE_NINF, syntax error. */ -#define YYTABLE_NINF -43 +#define YYTABLE_NINF -45 static const yytype_int8 yytable[] = { - 16, 21, -42, 63, 56, 64, 57, 16, 2, 58, - 59, 10, 28, 46, 33, 47, 65, 32, 60, 49, - 50, 51, -42, 32, 8, 48, 1, -42, 52, 2, - 53, 19, 20, 41, 2, 15, 17, 9, 42, 26, - 19, 20, 15, 13, 17, 24, 34, 35, 38, 39, - 23, 40, 66, 12, 22, 43, 0, 36, 0, 0, - 37 + 21, 16, 46, 8, 59, 47, 60, 9, 16, 61, + 62, 28, 66, 33, 67, 10, 48, 13, 32, 63, + 49, 50, 51, 52, 32, 17, 68, 19, 20, -44, + 53, -44, 54, 1, -44, 2, 26, 15, 2, 24, + 41, 2, 34, 17, 15, 42, 19, 20, 69, 70, + 35, 38, 39, 40, 58, 55, 72, 71, 73, 12, + 74, 22, 75, 23, 0, 0, 0, 0, 36, 0, + 0, 0, 43, 37 }; static const yytype_int8 yycheck[] = { - 8, 13, 5, 9, 6, 11, 8, 15, 11, 11, - 12, 15, 24, 11, 26, 13, 22, 25, 20, 10, - 11, 12, 4, 31, 13, 23, 3, 4, 19, 11, - 21, 6, 7, 13, 11, 8, 16, 0, 18, 14, - 6, 7, 15, 4, 16, 4, 13, 17, 5, 13, - 15, 13, 7, 6, 14, 38, -1, 31, -1, -1, - 31 + 13, 8, 11, 14, 6, 14, 8, 0, 15, 11, + 12, 24, 9, 26, 11, 16, 25, 4, 25, 21, + 10, 11, 12, 13, 31, 17, 23, 6, 7, 5, + 20, 4, 22, 3, 4, 11, 15, 8, 11, 4, + 14, 11, 14, 17, 15, 19, 6, 7, 25, 26, + 18, 5, 14, 14, 10, 24, 69, 7, 25, 6, + 73, 14, 26, 15, -1, -1, -1, -1, 31, -1, + -1, -1, 38, 31 }; /* YYSTOS[STATE-NUM] -- The (internal number of the) accessing symbol of state STATE-NUM. */ static const yytype_uint8 yystos[] = { - 0, 3, 11, 25, 27, 28, 29, 43, 13, 0, - 15, 31, 28, 4, 26, 27, 43, 16, 32, 6, - 7, 30, 31, 26, 4, 33, 14, 30, 30, 34, - 41, 42, 43, 30, 13, 17, 34, 41, 5, 13, - 13, 13, 18, 32, 35, 36, 11, 13, 23, 10, - 11, 12, 19, 21, 37, 40, 6, 8, 11, 12, - 20, 38, 39, 9, 11, 22, 7 + 0, 3, 11, 28, 30, 31, 32, 46, 14, 0, + 16, 34, 31, 4, 29, 30, 46, 17, 35, 6, + 7, 33, 34, 29, 4, 36, 15, 33, 33, 37, + 44, 45, 46, 33, 14, 18, 37, 44, 5, 14, + 14, 14, 19, 35, 38, 39, 11, 14, 25, 10, + 11, 12, 13, 20, 22, 24, 40, 43, 10, 6, + 8, 11, 12, 21, 41, 42, 9, 11, 23, 25, + 26, 7, 33, 25, 33, 26 }; #define yyerrok (yyerrstatus = 0) @@ -1440,289 +1452,323 @@ yyreduce: switch (yyn) { case 2: -#line 86 "dtc-parser.y" +#line 90 "dtc-parser.y" { - the_boot_info = build_boot_info((yyvsp[(3) - (4)].re), (yyvsp[(4) - (4)].node)); + the_boot_info = build_boot_info((yyvsp[(3) - (4)].re), (yyvsp[(4) - (4)].node), 0); ;} break; case 3: -#line 90 "dtc-parser.y" +#line 94 "dtc-parser.y" { - the_boot_info = build_boot_info((yyvsp[(1) - (2)].re), (yyvsp[(2) - (2)].node)); + the_boot_info = build_boot_info((yyvsp[(1) - (2)].re), (yyvsp[(2) - (2)].node), 0); ;} break; case 4: -#line 97 "dtc-parser.y" +#line 101 "dtc-parser.y" { (yyval.re) = NULL; ;} break; case 5: -#line 101 "dtc-parser.y" +#line 105 "dtc-parser.y" { (yyval.re) = chain_reserve_entry((yyvsp[(1) - (2)].re), (yyvsp[(2) - (2)].re)); ;} break; case 6: -#line 108 "dtc-parser.y" +#line 112 "dtc-parser.y" { (yyval.re) = build_reserve_entry((yyvsp[(3) - (5)].addr), (yyvsp[(4) - (5)].addr), (yyvsp[(1) - (5)].labelref)); ;} break; case 7: -#line 115 "dtc-parser.y" +#line 119 "dtc-parser.y" { (yyval.re) = NULL; ;} break; case 8: -#line 119 "dtc-parser.y" +#line 123 "dtc-parser.y" { (yyval.re) = chain_reserve_entry((yyvsp[(1) - (2)].re), (yyvsp[(2) - (2)].re)); ;} break; case 9: -#line 126 "dtc-parser.y" +#line 130 "dtc-parser.y" { (yyval.re) = (yyvsp[(1) - (1)].re); ;} break; case 10: -#line 130 "dtc-parser.y" +#line 134 "dtc-parser.y" { (yyval.re) = build_reserve_entry((yyvsp[(3) - (6)].addr), (yyvsp[(5) - (6)].addr) - (yyvsp[(3) - (6)].addr) + 1, (yyvsp[(1) - (6)].labelref)); ;} break; case 11: -#line 137 "dtc-parser.y" +#line 141 "dtc-parser.y" { (yyval.addr) = eval_literal((yyvsp[(1) - (1)].literal), 0, 64); ;} break; case 12: -#line 141 "dtc-parser.y" +#line 145 "dtc-parser.y" { (yyval.addr) = eval_literal((yyvsp[(1) - (1)].literal), 16, 64); ;} break; case 13: -#line 148 "dtc-parser.y" +#line 152 "dtc-parser.y" { (yyval.node) = name_node((yyvsp[(2) - (2)].node), "", NULL); ;} break; case 14: -#line 155 "dtc-parser.y" +#line 159 "dtc-parser.y" { (yyval.node) = build_node((yyvsp[(2) - (5)].proplist), (yyvsp[(3) - (5)].nodelist)); ;} break; case 15: -#line 162 "dtc-parser.y" +#line 166 "dtc-parser.y" { (yyval.proplist) = NULL; ;} break; case 16: -#line 166 "dtc-parser.y" +#line 170 "dtc-parser.y" { (yyval.proplist) = chain_property((yyvsp[(2) - (2)].prop), (yyvsp[(1) - (2)].proplist)); ;} break; case 17: -#line 173 "dtc-parser.y" +#line 177 "dtc-parser.y" { (yyval.prop) = build_property((yyvsp[(2) - (5)].propnodename), (yyvsp[(4) - (5)].data), (yyvsp[(1) - (5)].labelref)); ;} break; case 18: -#line 177 "dtc-parser.y" +#line 181 "dtc-parser.y" { (yyval.prop) = build_property((yyvsp[(2) - (3)].propnodename), empty_data, (yyvsp[(1) - (3)].labelref)); ;} break; case 19: -#line 184 "dtc-parser.y" +#line 188 "dtc-parser.y" { (yyval.data) = data_merge((yyvsp[(1) - (2)].data), (yyvsp[(2) - (2)].data)); ;} break; case 20: -#line 188 "dtc-parser.y" +#line 192 "dtc-parser.y" { (yyval.data) = data_merge((yyvsp[(1) - (4)].data), (yyvsp[(3) - (4)].data)); ;} break; case 21: -#line 192 "dtc-parser.y" +#line 196 "dtc-parser.y" { (yyval.data) = data_merge((yyvsp[(1) - (4)].data), (yyvsp[(3) - (4)].data)); ;} break; case 22: -#line 196 "dtc-parser.y" +#line 200 "dtc-parser.y" { (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), REF_PATH, (yyvsp[(2) - (2)].labelref)); ;} break; case 23: -#line 200 "dtc-parser.y" +#line 204 "dtc-parser.y" { - (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref)); + struct search_path path = { srcpos_file->dir, NULL, NULL }; + struct dtc_file *file = dtc_open_file((yyvsp[(4) - (9)].data).val, &path); + struct data d = empty_data; + + if ((yyvsp[(6) - (9)].addr) != 0) + if (fseek(file->file, (yyvsp[(6) - (9)].addr), SEEK_SET) != 0) + yyerrorf("Couldn't seek to offset %llu in \"%s\": %s", + (unsigned long long)(yyvsp[(6) - (9)].addr), + (yyvsp[(4) - (9)].data).val, strerror(errno)); + + d = data_copy_file(file->file, (yyvsp[(8) - (9)].addr)); + + (yyval.data) = data_merge((yyvsp[(1) - (9)].data), d); + dtc_close_file(file); ;} break; case 24: -#line 207 "dtc-parser.y" +#line 221 "dtc-parser.y" { - (yyval.data) = empty_data; + struct search_path path = { srcpos_file->dir, NULL, NULL }; + struct dtc_file *file = dtc_open_file((yyvsp[(4) - (5)].data).val, &path); + struct data d = empty_data; + + d = data_copy_file(file->file, -1); + + (yyval.data) = data_merge((yyvsp[(1) - (5)].data), d); + dtc_close_file(file); ;} break; case 25: -#line 211 "dtc-parser.y" +#line 232 "dtc-parser.y" { - (yyval.data) = (yyvsp[(1) - (2)].data); + (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref)); ;} break; case 26: -#line 215 "dtc-parser.y" +#line 239 "dtc-parser.y" { - (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref)); + (yyval.data) = empty_data; ;} break; case 27: -#line 222 "dtc-parser.y" +#line 243 "dtc-parser.y" { - (yyval.data) = empty_data; + (yyval.data) = (yyvsp[(1) - (2)].data); ;} break; case 28: -#line 226 "dtc-parser.y" +#line 247 "dtc-parser.y" { - (yyval.data) = data_append_cell((yyvsp[(1) - (2)].data), (yyvsp[(2) - (2)].cell)); + (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref)); ;} break; case 29: -#line 230 "dtc-parser.y" +#line 254 "dtc-parser.y" + { + (yyval.data) = empty_data; + ;} + break; + + case 30: +#line 258 "dtc-parser.y" + { + (yyval.data) = data_append_cell((yyvsp[(1) - (2)].data), (yyvsp[(2) - (2)].cell)); + ;} + break; + + case 31: +#line 262 "dtc-parser.y" { (yyval.data) = data_append_cell(data_add_marker((yyvsp[(1) - (2)].data), REF_PHANDLE, (yyvsp[(2) - (2)].labelref)), -1); ;} break; - case 30: -#line 235 "dtc-parser.y" + case 32: +#line 267 "dtc-parser.y" { (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref)); ;} break; - case 31: -#line 242 "dtc-parser.y" + case 33: +#line 274 "dtc-parser.y" { (yyval.cbase) = 16; ;} break; - case 33: -#line 250 "dtc-parser.y" + case 35: +#line 282 "dtc-parser.y" { (yyval.cell) = eval_literal((yyvsp[(1) - (1)].literal), 0, 32); ;} break; - case 34: -#line 254 "dtc-parser.y" + case 36: +#line 286 "dtc-parser.y" { (yyval.cell) = eval_literal((yyvsp[(2) - (2)].literal), (yyvsp[(1) - (2)].cbase), 32); ;} break; - case 35: -#line 261 "dtc-parser.y" + case 37: +#line 293 "dtc-parser.y" { (yyval.data) = empty_data; ;} break; - case 36: -#line 265 "dtc-parser.y" + case 38: +#line 297 "dtc-parser.y" { (yyval.data) = data_append_byte((yyvsp[(1) - (2)].data), (yyvsp[(2) - (2)].byte)); ;} break; - case 37: -#line 269 "dtc-parser.y" + case 39: +#line 301 "dtc-parser.y" { (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref)); ;} break; - case 38: -#line 276 "dtc-parser.y" + case 40: +#line 308 "dtc-parser.y" { (yyval.nodelist) = NULL; ;} break; - case 39: -#line 280 "dtc-parser.y" + case 41: +#line 312 "dtc-parser.y" { (yyval.nodelist) = chain_node((yyvsp[(1) - (2)].node), (yyvsp[(2) - (2)].nodelist)); ;} break; - case 40: -#line 284 "dtc-parser.y" + case 42: +#line 316 "dtc-parser.y" { - yyerror("syntax error: properties must precede subnodes\n"); + yyerror("syntax error: properties must precede subnodes"); YYERROR; ;} break; - case 41: -#line 292 "dtc-parser.y" + case 43: +#line 324 "dtc-parser.y" { (yyval.node) = name_node((yyvsp[(3) - (3)].node), (yyvsp[(2) - (3)].propnodename), (yyvsp[(1) - (3)].labelref)); ;} break; - case 42: -#line 299 "dtc-parser.y" + case 44: +#line 331 "dtc-parser.y" { (yyval.labelref) = NULL; ;} break; - case 43: -#line 303 "dtc-parser.y" + case 45: +#line 335 "dtc-parser.y" { (yyval.labelref) = (yyvsp[(1) - (1)].labelref); ;} @@ -1730,7 +1776,7 @@ yyreduce: /* Line 1267 of yacc.c. */ -#line 1734 "dtc-parser.tab.c" +#line 1780 "dtc-parser.tab.c" default: break; } YY_SYMBOL_PRINT ("-> $$ =", yyr1[yyn], &yyval, &yyloc); @@ -1950,21 +1996,32 @@ yyreturn: } -#line 308 "dtc-parser.y" +#line 340 "dtc-parser.y" -void yyerror (char const *s) +void yyerrorf(char const *s, ...) { - const char *fname = srcpos_filename_for_num(yylloc.filenum); + const char *fname = srcpos_file ? srcpos_file->name : ""; + va_list va; + va_start(va, s); if (strcmp(fname, "-") == 0) fname = "stdin"; - fprintf(stderr, "%s:%d %s\n", - fname, yylloc.first_line, s); + fprintf(stderr, "%s:%d ", fname, yylloc.first_line); + vfprintf(stderr, s, va); + fprintf(stderr, "\n"); + + treesource_error = 1; + va_end(va); +} + +void yyerror (char const *s) +{ + yyerrorf("%s", s); } -unsigned long long eval_literal(const char *s, int base, int bits) +static unsigned long long eval_literal(const char *s, int base, int bits) { unsigned long long val; char *e; diff --git a/arch/powerpc/boot/dtc-src/dtc-parser.tab.h_shipped b/arch/powerpc/boot/dtc-src/dtc-parser.tab.h_shipped index 4707b029ed2..ba99100d55c 100644 --- a/arch/powerpc/boot/dtc-src/dtc-parser.tab.h_shipped +++ b/arch/powerpc/boot/dtc-src/dtc-parser.tab.h_shipped @@ -48,7 +48,8 @@ DT_BYTE = 264, DT_STRING = 265, DT_LABEL = 266, - DT_REF = 267 + DT_REF = 267, + DT_INCBIN = 268 }; #endif /* Tokens. */ @@ -62,22 +63,23 @@ #define DT_STRING 265 #define DT_LABEL 266 #define DT_REF 267 +#define DT_INCBIN 268 #if ! defined YYSTYPE && ! defined YYSTYPE_IS_DECLARED typedef union YYSTYPE -#line 34 "dtc-parser.y" +#line 37 "dtc-parser.y" { char *propnodename; char *literal; char *labelref; unsigned int cbase; - u8 byte; + uint8_t byte; struct data data; - u64 addr; + uint64_t addr; cell_t cell; struct property *prop; struct property *proplist; @@ -86,7 +88,7 @@ typedef union YYSTYPE struct reserve_info *re; } /* Line 1489 of yacc.c. */ -#line 90 "dtc-parser.tab.h" +#line 92 "dtc-parser.tab.h" YYSTYPE; # define yystype YYSTYPE /* obsolescent; will be withdrawn */ # define YYSTYPE_IS_DECLARED 1 diff --git a/arch/powerpc/boot/dtc-src/dtc-parser.y b/arch/powerpc/boot/dtc-src/dtc-parser.y index 002ea7fef18..b2ab562420e 100644 --- a/arch/powerpc/boot/dtc-src/dtc-parser.y +++ b/arch/powerpc/boot/dtc-src/dtc-parser.y @@ -21,14 +21,17 @@ %locations %{ +#include + #include "dtc.h" #include "srcpos.h" -int yylex(void); -unsigned long long eval_literal(const char *s, int base, int bits); +extern int yylex(void); extern struct boot_info *the_boot_info; +extern int treesource_error; +static unsigned long long eval_literal(const char *s, int base, int bits); %} %union { @@ -36,10 +39,10 @@ extern struct boot_info *the_boot_info; char *literal; char *labelref; unsigned int cbase; - u8 byte; + uint8_t byte; struct data data; - u64 addr; + uint64_t addr; cell_t cell; struct property *prop; struct property *proplist; @@ -58,6 +61,7 @@ extern struct boot_info *the_boot_info; %token DT_STRING %token DT_LABEL %token DT_REF +%token DT_INCBIN %type propdata %type propdataprefix @@ -84,11 +88,11 @@ extern struct boot_info *the_boot_info; sourcefile: DT_V1 ';' memreserves devicetree { - the_boot_info = build_boot_info($3, $4); + the_boot_info = build_boot_info($3, $4, 0); } | v0_memreserves devicetree { - the_boot_info = build_boot_info($1, $2); + the_boot_info = build_boot_info($1, $2, 0); } ; @@ -196,6 +200,34 @@ propdata: { $$ = data_add_marker($1, REF_PATH, $2); } + | propdataprefix DT_INCBIN '(' DT_STRING ',' addr ',' addr ')' + { + struct search_path path = { srcpos_file->dir, NULL, NULL }; + struct dtc_file *file = dtc_open_file($4.val, &path); + struct data d = empty_data; + + if ($6 != 0) + if (fseek(file->file, $6, SEEK_SET) != 0) + yyerrorf("Couldn't seek to offset %llu in \"%s\": %s", + (unsigned long long)$6, + $4.val, strerror(errno)); + + d = data_copy_file(file->file, $8); + + $$ = data_merge($1, d); + dtc_close_file(file); + } + | propdataprefix DT_INCBIN '(' DT_STRING ')' + { + struct search_path path = { srcpos_file->dir, NULL, NULL }; + struct dtc_file *file = dtc_open_file($4.val, &path); + struct data d = empty_data; + + d = data_copy_file(file->file, -1); + + $$ = data_merge($1, d); + dtc_close_file(file); + } | propdata DT_LABEL { $$ = data_add_marker($1, LABEL, $2); @@ -282,7 +314,7 @@ subnodes: } | subnode propdef { - yyerror("syntax error: properties must precede subnodes\n"); + yyerror("syntax error: properties must precede subnodes"); YYERROR; } ; @@ -307,18 +339,29 @@ label: %% -void yyerror (char const *s) +void yyerrorf(char const *s, ...) { - const char *fname = srcpos_filename_for_num(yylloc.filenum); + const char *fname = srcpos_file ? srcpos_file->name : ""; + va_list va; + va_start(va, s); if (strcmp(fname, "-") == 0) fname = "stdin"; - fprintf(stderr, "%s:%d %s\n", - fname, yylloc.first_line, s); + fprintf(stderr, "%s:%d ", fname, yylloc.first_line); + vfprintf(stderr, s, va); + fprintf(stderr, "\n"); + + treesource_error = 1; + va_end(va); +} + +void yyerror (char const *s) +{ + yyerrorf("%s", s); } -unsigned long long eval_literal(const char *s, int base, int bits) +static unsigned long long eval_literal(const char *s, int base, int bits) { unsigned long long val; char *e; diff --git a/arch/powerpc/boot/dtc-src/dtc.c b/arch/powerpc/boot/dtc-src/dtc.c index 01131d7c2d5..d8fd43b4ac1 100644 --- a/arch/powerpc/boot/dtc-src/dtc.c +++ b/arch/powerpc/boot/dtc-src/dtc.c @@ -55,7 +55,7 @@ char *join_path(const char *path, const char *name) return str; } -void fill_fullpaths(struct node *tree, const char *prefix) +static void fill_fullpaths(struct node *tree, const char *prefix) { struct node *child; const char *unit; @@ -106,7 +106,7 @@ static void __attribute__ ((noreturn)) usage(void) fprintf(stderr, "\t\tForce - try to produce output even if the input tree has errors\n"); fprintf(stderr, "\t-v\n"); fprintf(stderr, "\t\tPrint DTC version and exit\n"); - exit(2); + exit(3); } int main(int argc, char *argv[]) @@ -118,10 +118,9 @@ int main(int argc, char *argv[]) int force = 0, check = 0; const char *arg; int opt; - FILE *inf = NULL; FILE *outf = NULL; int outversion = DEFAULT_FDT_VERSION; - int boot_cpuid_phys = 0xfeedbeef; + long long cmdline_boot_cpuid = -1; quiet = 0; reservenum = 0; @@ -161,11 +160,11 @@ int main(int argc, char *argv[]) quiet++; break; case 'b': - boot_cpuid_phys = strtol(optarg, NULL, 0); + cmdline_boot_cpuid = strtoll(optarg, NULL, 0); break; case 'v': - printf("Version: %s\n", DTC_VERSION); - exit(0); + printf("Version: %s\n", DTC_VERSION); + exit(0); case 'h': default: usage(); @@ -180,31 +179,27 @@ int main(int argc, char *argv[]) arg = argv[optind]; /* minsize and padsize are mutually exclusive */ - if ((minsize) && (padsize)) { + if (minsize && padsize) die("Can't set both -p and -S\n"); - } fprintf(stderr, "DTC: %s->%s on file \"%s\"\n", inform, outform, arg); - if (streq(inform, "dts")) { + if (streq(inform, "dts")) bi = dt_from_source(arg); - } else if (streq(inform, "fs")) { + else if (streq(inform, "fs")) bi = dt_from_fs(arg); - } else if(streq(inform, "dtb")) { - inf = dtc_open_file(arg); - bi = dt_from_blob(inf); - } else { + else if(streq(inform, "dtb")) + bi = dt_from_blob(arg); + else die("Unknown input format \"%s\"\n", inform); - } - if (inf && (inf != stdin)) - fclose(inf); + if (cmdline_boot_cpuid != -1) + bi->boot_cpuid_phys = cmdline_boot_cpuid; - if (! bi || ! bi->dt) - die("Couldn't read input tree\n"); + fill_fullpaths(bi->dt, ""); + process_checks(force, bi); - process_checks(force, bi, check, outversion, boot_cpuid_phys); if (streq(outname, "-")) { outf = stdout; @@ -218,9 +213,9 @@ int main(int argc, char *argv[]) if (streq(outform, "dts")) { dt_to_source(outf, bi); } else if (streq(outform, "dtb")) { - dt_to_blob(outf, bi, outversion, boot_cpuid_phys); + dt_to_blob(outf, bi, outversion); } else if (streq(outform, "asm")) { - dt_to_asm(outf, bi, outversion, boot_cpuid_phys); + dt_to_asm(outf, bi, outversion); } else if (streq(outform, "null")) { /* do nothing */ } else { diff --git a/arch/powerpc/boot/dtc-src/dtc.h b/arch/powerpc/boot/dtc-src/dtc.h index 65281777a16..08d54c87008 100644 --- a/arch/powerpc/boot/dtc-src/dtc.h +++ b/arch/powerpc/boot/dtc-src/dtc.h @@ -30,10 +30,8 @@ #include #include #include -#include -#include -#include +#include #include #define DEFAULT_FDT_VERSION 17 @@ -75,25 +73,8 @@ static inline void *xrealloc(void *p, size_t len) return new; } -typedef uint8_t u8; -typedef uint16_t u16; -typedef uint32_t u32; -typedef uint64_t u64; -typedef u32 cell_t; +typedef uint32_t cell_t; -#define cpu_to_be16(x) htons(x) -#define be16_to_cpu(x) ntohs(x) - -#define cpu_to_be32(x) htonl(x) -#define be32_to_cpu(x) ntohl(x) - -#if __BYTE_ORDER == __BIG_ENDIAN -#define cpu_to_be64(x) (x) -#define be64_to_cpu(x) (x) -#else -#define cpu_to_be64(x) bswap_64(x) -#define be64_to_cpu(x) bswap_64(x) -#endif #define streq(a, b) (strcmp((a), (b)) == 0) #define strneq(a, b, n) (strncmp((a), (b), (n)) == 0) @@ -118,7 +99,6 @@ struct marker { struct data { int len; char *val; - int asize; struct marker *markers; }; @@ -145,7 +125,7 @@ struct data data_insert_at_marker(struct data d, struct marker *m, struct data data_merge(struct data d1, struct data d2); struct data data_append_cell(struct data d, cell_t word); struct data data_append_re(struct data d, const struct fdt_reserve_entry *re); -struct data data_append_addr(struct data d, u64 addr); +struct data data_append_addr(struct data d, uint64_t addr); struct data data_append_byte(struct data d, uint8_t byte); struct data data_append_zeroes(struct data d, int len); struct data data_append_align(struct data d, int align); @@ -223,7 +203,7 @@ struct reserve_info { char *label; }; -struct reserve_info *build_reserve_entry(u64 start, u64 len, char *label); +struct reserve_info *build_reserve_entry(uint64_t start, uint64_t len, char *label); struct reserve_info *chain_reserve_entry(struct reserve_info *first, struct reserve_info *list); struct reserve_info *add_reserve_entry(struct reserve_info *list, @@ -233,24 +213,22 @@ struct reserve_info *add_reserve_entry(struct reserve_info *list, struct boot_info { struct reserve_info *reservelist; struct node *dt; /* the device tree */ + uint32_t boot_cpuid_phys; }; struct boot_info *build_boot_info(struct reserve_info *reservelist, - struct node *tree); + struct node *tree, uint32_t boot_cpuid_phys); /* Checks */ -void process_checks(int force, struct boot_info *bi, - int checkflag, int outversion, int boot_cpuid_phys); +void process_checks(int force, struct boot_info *bi); /* Flattened trees */ -void dt_to_blob(FILE *f, struct boot_info *bi, int version, - int boot_cpuid_phys); -void dt_to_asm(FILE *f, struct boot_info *bi, int version, - int boot_cpuid_phys); +void dt_to_blob(FILE *f, struct boot_info *bi, int version); +void dt_to_asm(FILE *f, struct boot_info *bi, int version); -struct boot_info *dt_from_blob(FILE *f); +struct boot_info *dt_from_blob(const char *fname); /* Tree source */ @@ -264,6 +242,5 @@ struct boot_info *dt_from_fs(const char *dirname); /* misc */ char *join_path(const char *path, const char *name); -void fill_fullpaths(struct node *tree, const char *prefix); #endif /* _DTC_H */ diff --git a/arch/powerpc/boot/dtc-src/flattree.c b/arch/powerpc/boot/dtc-src/flattree.c index a7cfb843d33..76acd28c068 100644 --- a/arch/powerpc/boot/dtc-src/flattree.c +++ b/arch/powerpc/boot/dtc-src/flattree.c @@ -19,6 +19,7 @@ */ #include "dtc.h" +#include "srcpos.h" #define FTF_FULLPATH 0x1 #define FTF_VARALIGN 0x2 @@ -162,28 +163,18 @@ static void asm_emit_data(void *e, struct data d) { FILE *f = e; int off = 0; - struct marker *m; + struct marker *m = d.markers; - m = d.markers; - while (m) { - if (m->type == LABEL) - emit_offset_label(f, m->ref, m->offset); - m = m->next; - } + for_each_marker_of_type(m, LABEL) + emit_offset_label(f, m->ref, m->offset); - while ((d.len - off) >= sizeof(u32)) { + while ((d.len - off) >= sizeof(uint32_t)) { fprintf(f, "\t.long\t0x%x\n", - be32_to_cpu(*((u32 *)(d.val+off)))); - off += sizeof(u32); - } - - if ((d.len - off) >= sizeof(u16)) { - fprintf(f, "\t.short\t0x%hx\n", - be16_to_cpu(*((u16 *)(d.val+off)))); - off += sizeof(u16); + fdt32_to_cpu(*((uint32_t *)(d.val+off)))); + off += sizeof(uint32_t); } - if ((d.len - off) >= 1) { + while ((d.len - off) >= 1) { fprintf(f, "\t.byte\t0x%hhx\n", d.val[off]); off += 1; } @@ -336,29 +327,28 @@ static void make_fdt_header(struct fdt_header *fdt, memset(fdt, 0xff, sizeof(*fdt)); - fdt->magic = cpu_to_be32(FDT_MAGIC); - fdt->version = cpu_to_be32(vi->version); - fdt->last_comp_version = cpu_to_be32(vi->last_comp_version); + fdt->magic = cpu_to_fdt32(FDT_MAGIC); + fdt->version = cpu_to_fdt32(vi->version); + fdt->last_comp_version = cpu_to_fdt32(vi->last_comp_version); /* Reserve map should be doubleword aligned */ reserve_off = ALIGN(vi->hdr_size, 8); - fdt->off_mem_rsvmap = cpu_to_be32(reserve_off); - fdt->off_dt_struct = cpu_to_be32(reserve_off + reservesize); - fdt->off_dt_strings = cpu_to_be32(reserve_off + reservesize + fdt->off_mem_rsvmap = cpu_to_fdt32(reserve_off); + fdt->off_dt_struct = cpu_to_fdt32(reserve_off + reservesize); + fdt->off_dt_strings = cpu_to_fdt32(reserve_off + reservesize + dtsize); - fdt->totalsize = cpu_to_be32(reserve_off + reservesize + dtsize + strsize); + fdt->totalsize = cpu_to_fdt32(reserve_off + reservesize + dtsize + strsize); if (vi->flags & FTF_BOOTCPUID) - fdt->boot_cpuid_phys = cpu_to_be32(boot_cpuid_phys); + fdt->boot_cpuid_phys = cpu_to_fdt32(boot_cpuid_phys); if (vi->flags & FTF_STRTABSIZE) - fdt->size_dt_strings = cpu_to_be32(strsize); + fdt->size_dt_strings = cpu_to_fdt32(strsize); if (vi->flags & FTF_STRUCTSIZE) - fdt->size_dt_struct = cpu_to_be32(dtsize); + fdt->size_dt_struct = cpu_to_fdt32(dtsize); } -void dt_to_blob(FILE *f, struct boot_info *bi, int version, - int boot_cpuid_phys) +void dt_to_blob(FILE *f, struct boot_info *bi, int version) { struct version_info *vi = NULL; int i; @@ -383,26 +373,26 @@ void dt_to_blob(FILE *f, struct boot_info *bi, int version, /* Make header */ make_fdt_header(&fdt, vi, reservebuf.len, dtbuf.len, strbuf.len, - boot_cpuid_phys); + bi->boot_cpuid_phys); /* * If the user asked for more space than is used, adjust the totalsize. */ if (minsize > 0) { - padlen = minsize - be32_to_cpu(fdt.totalsize); + padlen = minsize - fdt32_to_cpu(fdt.totalsize); if ((padlen < 0) && (quiet < 1)) fprintf(stderr, "Warning: blob size %d >= minimum size %d\n", - be32_to_cpu(fdt.totalsize), minsize); + fdt32_to_cpu(fdt.totalsize), minsize); } if (padsize > 0) padlen = padsize; if (padlen > 0) { - int tsize = be32_to_cpu(fdt.totalsize); + int tsize = fdt32_to_cpu(fdt.totalsize); tsize += padlen; - fdt.totalsize = cpu_to_be32(tsize); + fdt.totalsize = cpu_to_fdt32(tsize); } /* @@ -410,7 +400,7 @@ void dt_to_blob(FILE *f, struct boot_info *bi, int version, * the reserve buffer, add the reserve map terminating zeroes, * the device tree itself, and finally the strings. */ - blob = data_append_data(blob, &fdt, sizeof(fdt)); + blob = data_append_data(blob, &fdt, vi->hdr_size); blob = data_append_align(blob, 8); blob = data_merge(blob, reservebuf); blob = data_append_zeroes(blob, sizeof(struct fdt_reserve_entry)); @@ -449,7 +439,7 @@ static void dump_stringtable_asm(FILE *f, struct data strbuf) } } -void dt_to_asm(FILE *f, struct boot_info *bi, int version, int boot_cpuid_phys) +void dt_to_asm(FILE *f, struct boot_info *bi, int version) { struct version_info *vi = NULL; int i; @@ -489,7 +479,7 @@ void dt_to_asm(FILE *f, struct boot_info *bi, int version, int boot_cpuid_phys) if (vi->flags & FTF_BOOTCPUID) fprintf(f, "\t.long\t%i\t\t\t\t\t/* boot_cpuid_phys */\n", - boot_cpuid_phys); + bi->boot_cpuid_phys); if (vi->flags & FTF_STRTABSIZE) fprintf(f, "\t.long\t_%s_strings_end - _%s_strings_start\t/* size_dt_strings */\n", @@ -579,15 +569,15 @@ static void flat_read_chunk(struct inbuf *inb, void *p, int len) inb->ptr += len; } -static u32 flat_read_word(struct inbuf *inb) +static uint32_t flat_read_word(struct inbuf *inb) { - u32 val; + uint32_t val; assert(((inb->ptr - inb->base) % sizeof(val)) == 0); flat_read_chunk(inb, &val, sizeof(val)); - return be32_to_cpu(val); + return fdt32_to_cpu(val); } static void flat_realign(struct inbuf *inb, int align) @@ -615,7 +605,7 @@ static char *flat_read_string(struct inbuf *inb) inb->ptr += len; - flat_realign(inb, sizeof(u32)); + flat_realign(inb, sizeof(uint32_t)); return str; } @@ -632,7 +622,7 @@ static struct data flat_read_data(struct inbuf *inb, int len) flat_read_chunk(inb, d.val, len); - flat_realign(inb, sizeof(u32)); + flat_realign(inb, sizeof(uint32_t)); return d; } @@ -659,7 +649,7 @@ static char *flat_read_stringtable(struct inbuf *inb, int offset) static struct property *flat_read_property(struct inbuf *dtbuf, struct inbuf *strbuf, int flags) { - u32 proplen, stroff; + uint32_t proplen, stroff; char *name; struct data val; @@ -693,8 +683,8 @@ static struct reserve_info *flat_read_mem_reserve(struct inbuf *inb) p = inb->ptr; while (1) { flat_read_chunk(inb, &re, sizeof(re)); - re.address = be64_to_cpu(re.address); - re.size = be64_to_cpu(re.size); + re.address = fdt64_to_cpu(re.address); + re.size = fdt64_to_cpu(re.size); if (re.size == 0) break; @@ -708,77 +698,37 @@ static struct reserve_info *flat_read_mem_reserve(struct inbuf *inb) static char *nodename_from_path(const char *ppath, const char *cpath) { - const char *lslash; int plen; - lslash = strrchr(cpath, '/'); - if (! lslash) - return NULL; - - plen = lslash - cpath; - - if (streq(cpath, "/") && streq(ppath, "")) - return ""; - - if ((plen == 0) && streq(ppath, "/")) - return strdup(lslash+1); - - if (! strneq(ppath, cpath, plen)) - return NULL; - - return strdup(lslash+1); -} - -static const char PROPCHAR[] = "abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789,._+*#?-"; -static const char UNITCHAR[] = "0123456789abcdef,"; - -static int check_node_name(const char *name) -{ - const char *atpos; - int basenamelen; + plen = strlen(ppath); - atpos = strrchr(name, '@'); + if (!strneq(ppath, cpath, plen)) + die("Path \"%s\" is not valid as a child of \"%s\"\n", + cpath, ppath); - if (atpos) - basenamelen = atpos - name; - else - basenamelen = strlen(name); - - if (strspn(name, PROPCHAR) < basenamelen) - return -1; + /* root node is a special case */ + if (!streq(ppath, "/")) + plen++; - if (atpos - && ((basenamelen + 1 + strspn(atpos+1, UNITCHAR)) < strlen(name))) - return -1; - - return basenamelen; + return strdup(cpath + plen); } static struct node *unflatten_tree(struct inbuf *dtbuf, struct inbuf *strbuf, - const char *parent_path, int flags) + const char *parent_flatname, int flags) { struct node *node; - u32 val; + char *flatname; + uint32_t val; node = build_node(NULL, NULL); - if (flags & FTF_FULLPATH) { - node->fullpath = flat_read_string(dtbuf); - node->name = nodename_from_path(parent_path, node->fullpath); - - if (! node->name) - die("Path \"%s\" is not valid as a child of \"%s\"\n", - node->fullpath, parent_path); - } else { - node->name = flat_read_string(dtbuf); - node->fullpath = join_path(parent_path, node->name); - } + flatname = flat_read_string(dtbuf); - node->basenamelen = check_node_name(node->name); - if (node->basenamelen < 0) { - fprintf(stderr, "Warning \"%s\" has incorrect format\n", node->name); - } + if (flags & FTF_FULLPATH) + node->name = nodename_from_path(parent_flatname, flatname); + else + node->name = flatname; do { struct property *prop; @@ -795,8 +745,7 @@ static struct node *unflatten_tree(struct inbuf *dtbuf, break; case FDT_BEGIN_NODE: - child = unflatten_tree(dtbuf,strbuf, node->fullpath, - flags); + child = unflatten_tree(dtbuf,strbuf, flatname, flags); add_child(node, child); break; @@ -825,10 +774,11 @@ static struct node *unflatten_tree(struct inbuf *dtbuf, } -struct boot_info *dt_from_blob(FILE *f) +struct boot_info *dt_from_blob(const char *fname) { - u32 magic, totalsize, version, size_str, size_dt; - u32 off_dt, off_str, off_mem_rsvmap; + struct dtc_file *dtcf; + uint32_t magic, totalsize, version, size_dt, boot_cpuid_phys; + uint32_t off_dt, off_str, off_mem_rsvmap; int rc; char *blob; struct fdt_header *fdt; @@ -838,54 +788,56 @@ struct boot_info *dt_from_blob(FILE *f) int sizeleft; struct reserve_info *reservelist; struct node *tree; - u32 val; + uint32_t val; int flags = 0; - rc = fread(&magic, sizeof(magic), 1, f); - if (ferror(f)) + dtcf = dtc_open_file(fname, NULL); + + rc = fread(&magic, sizeof(magic), 1, dtcf->file); + if (ferror(dtcf->file)) die("Error reading DT blob magic number: %s\n", strerror(errno)); if (rc < 1) { - if (feof(f)) + if (feof(dtcf->file)) die("EOF reading DT blob magic number\n"); else die("Mysterious short read reading magic number\n"); } - magic = be32_to_cpu(magic); + magic = fdt32_to_cpu(magic); if (magic != FDT_MAGIC) die("Blob has incorrect magic number\n"); - rc = fread(&totalsize, sizeof(totalsize), 1, f); - if (ferror(f)) + rc = fread(&totalsize, sizeof(totalsize), 1, dtcf->file); + if (ferror(dtcf->file)) die("Error reading DT blob size: %s\n", strerror(errno)); if (rc < 1) { - if (feof(f)) + if (feof(dtcf->file)) die("EOF reading DT blob size\n"); else die("Mysterious short read reading blob size\n"); } - totalsize = be32_to_cpu(totalsize); + totalsize = fdt32_to_cpu(totalsize); if (totalsize < FDT_V1_SIZE) die("DT blob size (%d) is too small\n", totalsize); blob = xmalloc(totalsize); fdt = (struct fdt_header *)blob; - fdt->magic = cpu_to_be32(magic); - fdt->totalsize = cpu_to_be32(totalsize); + fdt->magic = cpu_to_fdt32(magic); + fdt->totalsize = cpu_to_fdt32(totalsize); sizeleft = totalsize - sizeof(magic) - sizeof(totalsize); p = blob + sizeof(magic) + sizeof(totalsize); while (sizeleft) { - if (feof(f)) + if (feof(dtcf->file)) die("EOF before reading %d bytes of DT blob\n", totalsize); - rc = fread(p, 1, sizeleft, f); - if (ferror(f)) + rc = fread(p, 1, sizeleft, dtcf->file); + if (ferror(dtcf->file)) die("Error reading DT blob: %s\n", strerror(errno)); @@ -893,19 +845,11 @@ struct boot_info *dt_from_blob(FILE *f) p += rc; } - off_dt = be32_to_cpu(fdt->off_dt_struct); - off_str = be32_to_cpu(fdt->off_dt_strings); - off_mem_rsvmap = be32_to_cpu(fdt->off_mem_rsvmap); - version = be32_to_cpu(fdt->version); - - fprintf(stderr, "\tmagic:\t\t\t0x%x\n", magic); - fprintf(stderr, "\ttotalsize:\t\t%d\n", totalsize); - fprintf(stderr, "\toff_dt_struct:\t\t0x%x\n", off_dt); - fprintf(stderr, "\toff_dt_strings:\t\t0x%x\n", off_str); - fprintf(stderr, "\toff_mem_rsvmap:\t\t0x%x\n", off_mem_rsvmap); - fprintf(stderr, "\tversion:\t\t0x%x\n", version ); - fprintf(stderr, "\tlast_comp_version:\t0x%x\n", - be32_to_cpu(fdt->last_comp_version)); + off_dt = fdt32_to_cpu(fdt->off_dt_struct); + off_str = fdt32_to_cpu(fdt->off_dt_strings); + off_mem_rsvmap = fdt32_to_cpu(fdt->off_mem_rsvmap); + version = fdt32_to_cpu(fdt->version); + boot_cpuid_phys = fdt32_to_cpu(fdt->boot_cpuid_phys); if (off_mem_rsvmap >= totalsize) die("Mem Reserve structure offset exceeds total size\n"); @@ -916,21 +860,17 @@ struct boot_info *dt_from_blob(FILE *f) if (off_str > totalsize) die("String table offset exceeds total size\n"); - if (version >= 2) - fprintf(stderr, "\tboot_cpuid_phys:\t0x%x\n", - be32_to_cpu(fdt->boot_cpuid_phys)); - - size_str = -1; if (version >= 3) { - size_str = be32_to_cpu(fdt->size_dt_strings); - fprintf(stderr, "\tsize_dt_strings:\t%d\n", size_str); + uint32_t size_str = fdt32_to_cpu(fdt->size_dt_strings); if (off_str+size_str > totalsize) die("String table extends past total size\n"); + inbuf_init(&strbuf, blob + off_str, blob + off_str + size_str); + } else { + inbuf_init(&strbuf, blob + off_str, blob + totalsize); } if (version >= 17) { - size_dt = be32_to_cpu(fdt->size_dt_struct); - fprintf(stderr, "\tsize_dt_struct:\t\t%d\n", size_dt); + size_dt = fdt32_to_cpu(fdt->size_dt_struct); if (off_dt+size_dt > totalsize) die("Structure block extends past total size\n"); } @@ -944,10 +884,6 @@ struct boot_info *dt_from_blob(FILE *f) inbuf_init(&memresvbuf, blob + off_mem_rsvmap, blob + totalsize); inbuf_init(&dtbuf, blob + off_dt, blob + totalsize); - if (size_str >= 0) - inbuf_init(&strbuf, blob + off_str, blob + off_str + size_str); - else - inbuf_init(&strbuf, blob + off_str, blob + totalsize); reservelist = flat_read_mem_reserve(&memresvbuf); @@ -964,5 +900,7 @@ struct boot_info *dt_from_blob(FILE *f) free(blob); - return build_boot_info(reservelist, tree); + dtc_close_file(dtcf); + + return build_boot_info(reservelist, tree, boot_cpuid_phys); } diff --git a/arch/powerpc/boot/dtc-src/fstree.c b/arch/powerpc/boot/dtc-src/fstree.c index 2a160a46998..766b2694d93 100644 --- a/arch/powerpc/boot/dtc-src/fstree.c +++ b/arch/powerpc/boot/dtc-src/fstree.c @@ -31,8 +31,8 @@ static struct node *read_fstree(const char *dirname) struct node *tree; d = opendir(dirname); - if (! d) - die("opendir(): %s\n", strerror(errno)); + if (!d) + die("Couldn't opendir() \"%s\": %s\n", dirname, strerror(errno)); tree = build_node(NULL, NULL); @@ -87,8 +87,6 @@ struct boot_info *dt_from_fs(const char *dirname) tree = read_fstree(dirname); tree = name_node(tree, "", NULL); - fill_fullpaths(tree, ""); - - return build_boot_info(NULL, tree); + return build_boot_info(NULL, tree, 0); } diff --git a/arch/powerpc/boot/dtc-src/libfdt_env.h b/arch/powerpc/boot/dtc-src/libfdt_env.h new file mode 100644 index 00000000000..449bf602daf --- /dev/null +++ b/arch/powerpc/boot/dtc-src/libfdt_env.h @@ -0,0 +1,23 @@ +#ifndef _LIBFDT_ENV_H +#define _LIBFDT_ENV_H + +#include +#include +#include + +#define _B(n) ((unsigned long long)((uint8_t *)&x)[n]) +static inline uint32_t fdt32_to_cpu(uint32_t x) +{ + return (_B(0) << 24) | (_B(1) << 16) | (_B(2) << 8) | _B(3); +} +#define cpu_to_fdt32(x) fdt32_to_cpu(x) + +static inline uint64_t fdt64_to_cpu(uint64_t x) +{ + return (_B(0) << 56) | (_B(1) << 48) | (_B(2) << 40) | (_B(3) << 32) + | (_B(4) << 24) | (_B(5) << 16) | (_B(6) << 8) | _B(7); +} +#define cpu_to_fdt64(x) fdt64_to_cpu(x) +#undef _B + +#endif /* _LIBFDT_ENV_H */ diff --git a/arch/powerpc/boot/dtc-src/livetree.c b/arch/powerpc/boot/dtc-src/livetree.c index 6ba0846b431..0ca3de550b3 100644 --- a/arch/powerpc/boot/dtc-src/livetree.c +++ b/arch/powerpc/boot/dtc-src/livetree.c @@ -115,6 +115,7 @@ void add_child(struct node *parent, struct node *child) struct node **p; child->next_sibling = NULL; + child->parent = parent; p = &parent->children; while (*p) @@ -123,7 +124,8 @@ void add_child(struct node *parent, struct node *child) *p = child; } -struct reserve_info *build_reserve_entry(u64 address, u64 size, char *label) +struct reserve_info *build_reserve_entry(uint64_t address, uint64_t size, + char *label) { struct reserve_info *new = xmalloc(sizeof(*new)); @@ -165,13 +167,14 @@ struct reserve_info *add_reserve_entry(struct reserve_info *list, } struct boot_info *build_boot_info(struct reserve_info *reservelist, - struct node *tree) + struct node *tree, uint32_t boot_cpuid_phys) { struct boot_info *bi; bi = xmalloc(sizeof(*bi)); bi->reservelist = reservelist; bi->dt = tree; + bi->boot_cpuid_phys = boot_cpuid_phys; return bi; } @@ -202,7 +205,7 @@ struct property *get_property(struct node *node, const char *propname) cell_t propval_cell(struct property *prop) { assert(prop->val.len == sizeof(cell_t)); - return be32_to_cpu(*((cell_t *)prop->val.val)); + return fdt32_to_cpu(*((cell_t *)prop->val.val)); } struct node *get_subnode(struct node *node, const char *nodename) diff --git a/arch/powerpc/boot/dtc-src/srcpos.c b/arch/powerpc/boot/dtc-src/srcpos.c index 352b0fe06fd..9641b7628b4 100644 --- a/arch/powerpc/boot/dtc-src/srcpos.c +++ b/arch/powerpc/boot/dtc-src/srcpos.c @@ -20,86 +20,97 @@ #include "dtc.h" #include "srcpos.h" - -/* - * Record the complete unique set of opened file names. - * Primarily used to cache source position file names. - */ -#define MAX_N_FILE_NAMES (100) - -const char *file_names[MAX_N_FILE_NAMES]; -static int n_file_names = 0; - /* * Like yylineno, this is the current open file pos. */ -int srcpos_filenum = -1; - +struct dtc_file *srcpos_file; - -FILE *dtc_open_file(const char *fname) +static int dtc_open_one(struct dtc_file *file, + const char *search, + const char *fname) { - FILE *f; + char *fullname; - if (lookup_file_name(fname, 1) < 0) - die("Too many files opened\n"); + if (search) { + fullname = xmalloc(strlen(search) + strlen(fname) + 2); - if (streq(fname, "-")) - f = stdin; - else - f = fopen(fname, "r"); + strcpy(fullname, search); + strcat(fullname, "/"); + strcat(fullname, fname); + } else { + fullname = strdup(fname); + } - if (! f) - die("Couldn't open \"%s\": %s\n", fname, strerror(errno)); + file->file = fopen(fullname, "r"); + if (!file->file) { + free(fullname); + return 0; + } - return f; + file->name = fullname; + return 1; } +struct dtc_file *dtc_open_file(const char *fname, + const struct search_path *search) +{ + static const struct search_path default_search = { NULL, NULL, NULL }; -/* - * Locate and optionally add filename fname in the file_names[] array. - * - * If the filename is currently not in the array and the boolean - * add_it is non-zero, an attempt to add the filename will be made. - * - * Returns; - * Index [0..MAX_N_FILE_NAMES) where the filename is kept - * -1 if the name can not be recorded - */ + struct dtc_file *file; + const char *slash; -int lookup_file_name(const char *fname, int add_it) -{ - int i; + file = xmalloc(sizeof(struct dtc_file)); - for (i = 0; i < n_file_names; i++) { - if (strcmp(file_names[i], fname) == 0) - return i; + slash = strrchr(fname, '/'); + if (slash) { + char *dir = xmalloc(slash - fname + 1); + + memcpy(dir, fname, slash - fname); + dir[slash - fname] = 0; + file->dir = dir; + } else { + file->dir = NULL; } - if (add_it) { - if (n_file_names < MAX_N_FILE_NAMES) { - file_names[n_file_names] = strdup(fname); - return n_file_names++; - } + if (streq(fname, "-")) { + file->name = "stdin"; + file->file = stdin; + return file; } - return -1; -} + if (fname[0] == '/') { + file->file = fopen(fname, "r"); + if (!file->file) + goto fail; + + file->name = strdup(fname); + return file; + } + if (!search) + search = &default_search; -const char *srcpos_filename_for_num(int filenum) -{ - if (0 <= filenum && filenum < n_file_names) { - return file_names[filenum]; + while (search) { + if (dtc_open_one(file, search->dir, fname)) + return file; + + if (errno != ENOENT) + goto fail; + + search = search->next; } - return 0; +fail: + die("Couldn't open \"%s\": %s\n", fname, strerror(errno)); } - -const char *srcpos_get_filename(void) +void dtc_close_file(struct dtc_file *file) { - return srcpos_filename_for_num(srcpos_filenum); + if (fclose(file->file)) + die("Error closing \"%s\": %s\n", file->name, strerror(errno)); + + free(file->dir); + free(file); } diff --git a/arch/powerpc/boot/dtc-src/srcpos.h b/arch/powerpc/boot/dtc-src/srcpos.h index ce7ab5ba5b4..e17c7c04db8 100644 --- a/arch/powerpc/boot/dtc-src/srcpos.h +++ b/arch/powerpc/boot/dtc-src/srcpos.h @@ -22,13 +22,21 @@ * array of all opened filenames. */ +#include + +struct dtc_file { + char *dir; + const char *name; + FILE *file; +}; + #if ! defined(YYLTYPE) && ! defined(YYLTYPE_IS_DECLARED) typedef struct YYLTYPE { int first_line; int first_column; int last_line; int last_column; - int filenum; + struct dtc_file *file; } YYLTYPE; #define YYLTYPE_IS_DECLARED 1 @@ -48,7 +56,7 @@ typedef struct YYLTYPE { (Current).first_column = YYRHSLOC (Rhs, 1).first_column; \ (Current).last_line = YYRHSLOC (Rhs, N).last_line; \ (Current).last_column = YYRHSLOC (Rhs, N).last_column; \ - (Current).filenum = YYRHSLOC (Rhs, N).filenum; \ + (Current).file = YYRHSLOC (Rhs, N).file; \ } \ else \ { \ @@ -56,20 +64,22 @@ typedef struct YYLTYPE { YYRHSLOC (Rhs, 0).last_line; \ (Current).first_column = (Current).last_column = \ YYRHSLOC (Rhs, 0).last_column; \ - (Current).filenum = YYRHSLOC (Rhs, 0).filenum; \ + (Current).file = YYRHSLOC (Rhs, 0).file; \ } \ while (YYID (0)) extern void yyerror(char const *); +extern void yyerrorf(char const *, ...) __attribute__((format(printf, 1, 2))); -extern int srcpos_filenum; +extern struct dtc_file *srcpos_file; -extern int push_input_file(const char *filename); -extern int pop_input_file(void); +struct search_path { + const char *dir; /* NULL for current directory */ + struct search_path *prev, *next; +}; -extern FILE *dtc_open_file(const char *fname); -extern int lookup_file_name(const char *fname, int add_it); -extern const char *srcpos_filename_for_num(int filenum); -const char *srcpos_get_filename(void); +extern struct dtc_file *dtc_open_file(const char *fname, + const struct search_path *search); +extern void dtc_close_file(struct dtc_file *file); diff --git a/arch/powerpc/boot/dtc-src/treesource.c b/arch/powerpc/boot/dtc-src/treesource.c index a6a77679763..ebeb6eb2790 100644 --- a/arch/powerpc/boot/dtc-src/treesource.c +++ b/arch/powerpc/boot/dtc-src/treesource.c @@ -23,20 +23,23 @@ extern FILE *yyin; extern int yyparse(void); -extern void yyerror(char const *); struct boot_info *the_boot_info; +int treesource_error; struct boot_info *dt_from_source(const char *fname) { the_boot_info = NULL; + treesource_error = 0; - push_input_file(fname); + srcpos_file = dtc_open_file(fname, NULL); + yyin = srcpos_file->file; if (yyparse() != 0) - return NULL; + die("Unable to parse input tree\n"); - fill_fullpaths(the_boot_info->dt, ""); + if (treesource_error) + die("Syntax error parsing input tree\n"); return the_boot_info; } @@ -144,7 +147,7 @@ static void write_propval_cells(FILE *f, struct data val) m = m->next; } - fprintf(f, "0x%x", be32_to_cpu(*cp++)); + fprintf(f, "0x%x", fdt32_to_cpu(*cp++)); if ((void *)cp >= propend) break; fprintf(f, " "); @@ -173,7 +176,7 @@ static void write_propval_bytes(FILE *f, struct data val) } fprintf(f, "%02hhx", *bp++); - if ((void *)bp >= propend) + if ((const void *)bp >= propend) break; fprintf(f, " "); } diff --git a/arch/powerpc/boot/dtc-src/version_gen.h b/arch/powerpc/boot/dtc-src/version_gen.h index 6c343031538..658ff42429d 100644 --- a/arch/powerpc/boot/dtc-src/version_gen.h +++ b/arch/powerpc/boot/dtc-src/version_gen.h @@ -1 +1 @@ -#define DTC_VERSION "DTC 1.0.0-gd6f9b62f" +#define DTC_VERSION "DTC 1.2.0" diff --git a/arch/powerpc/boot/libfdt/Makefile.libfdt b/arch/powerpc/boot/libfdt/Makefile.libfdt index 82f9c6a8287..6c42acfa21e 100644 --- a/arch/powerpc/boot/libfdt/Makefile.libfdt +++ b/arch/powerpc/boot/libfdt/Makefile.libfdt @@ -3,12 +3,6 @@ # This is not a complete Makefile of itself. Instead, it is designed to # be easily embeddable into other systems of Makefiles. # -LIBFDT_SRCS = fdt.c fdt_ro.c fdt_wip.c fdt_sw.c fdt_rw.c fdt_strerror.c LIBFDT_INCLUDES = fdt.h libfdt.h -LIBFDT_EXTRA = libfdt_internal.h -LIBFDT_LIB = libfdt/libfdt.a - +LIBFDT_SRCS = fdt.c fdt_ro.c fdt_wip.c fdt_sw.c fdt_rw.c fdt_strerror.c LIBFDT_OBJS = $(LIBFDT_SRCS:%.c=%.o) - -$(LIBFDT_objdir)/$(LIBFDT_LIB): $(addprefix $(LIBFDT_objdir)/,$(LIBFDT_OBJS)) - diff --git a/arch/powerpc/boot/libfdt/fdt.c b/arch/powerpc/boot/libfdt/fdt.c index 586a36136db..2acaec5923a 100644 --- a/arch/powerpc/boot/libfdt/fdt.c +++ b/arch/powerpc/boot/libfdt/fdt.c @@ -63,7 +63,7 @@ int fdt_check_header(const void *fdt) return -FDT_ERR_BADVERSION; if (fdt_last_comp_version(fdt) > FDT_LAST_SUPPORTED_VERSION) return -FDT_ERR_BADVERSION; - } else if (fdt_magic(fdt) == SW_MAGIC) { + } else if (fdt_magic(fdt) == FDT_SW_MAGIC) { /* Unfinished sequential-write blob */ if (fdt_size_dt_struct(fdt) == 0) return -FDT_ERR_BADSTATE; @@ -76,7 +76,7 @@ int fdt_check_header(const void *fdt) const void *fdt_offset_ptr(const void *fdt, int offset, int len) { - const void *p; + const char *p; if (fdt_version(fdt) >= 0x11) if (((offset + len) < offset) @@ -124,11 +124,59 @@ uint32_t fdt_next_tag(const void *fdt, int offset, int *nextoffset) } if (nextoffset) - *nextoffset = ALIGN(offset, FDT_TAGSIZE); + *nextoffset = FDT_TAGALIGN(offset); return tag; } +int _fdt_check_node_offset(const void *fdt, int offset) +{ + if ((offset < 0) || (offset % FDT_TAGSIZE) + || (fdt_next_tag(fdt, offset, &offset) != FDT_BEGIN_NODE)) + return -FDT_ERR_BADOFFSET; + + return offset; +} + +int fdt_next_node(const void *fdt, int offset, int *depth) +{ + int nextoffset = 0; + uint32_t tag; + + if (offset >= 0) + if ((nextoffset = _fdt_check_node_offset(fdt, offset)) < 0) + return nextoffset; + + do { + offset = nextoffset; + tag = fdt_next_tag(fdt, offset, &nextoffset); + + switch (tag) { + case FDT_PROP: + case FDT_NOP: + break; + + case FDT_BEGIN_NODE: + if (depth) + (*depth)++; + break; + + case FDT_END_NODE: + if (depth) + (*depth)--; + break; + + case FDT_END: + return -FDT_ERR_NOTFOUND; + + default: + return -FDT_ERR_BADSTRUCTURE; + } + } while (tag != FDT_BEGIN_NODE); + + return offset; +} + const char *_fdt_find_string(const char *strtab, int tabsize, const char *s) { int len = strlen(s) + 1; @@ -136,17 +184,14 @@ const char *_fdt_find_string(const char *strtab, int tabsize, const char *s) const char *p; for (p = strtab; p <= last; p++) - if (memeq(p, s, len)) + if (memcmp(p, s, len) == 0) return p; return NULL; } int fdt_move(const void *fdt, void *buf, int bufsize) { - int err = fdt_check_header(fdt); - - if (err) - return err; + FDT_CHECK_HEADER(fdt); if (fdt_totalsize(fdt) > bufsize) return -FDT_ERR_NOSPACE; diff --git a/arch/powerpc/boot/libfdt/fdt_ro.c b/arch/powerpc/boot/libfdt/fdt_ro.c index 12a37d59f96..129b532bcc1 100644 --- a/arch/powerpc/boot/libfdt/fdt_ro.c +++ b/arch/powerpc/boot/libfdt/fdt_ro.c @@ -55,17 +55,10 @@ #include "libfdt_internal.h" -#define CHECK_HEADER(fdt) \ - { \ - int err; \ - if ((err = fdt_check_header(fdt)) != 0) \ - return err; \ - } - -static int nodename_eq(const void *fdt, int offset, - const char *s, int len) +static int _fdt_nodename_eq(const void *fdt, int offset, + const char *s, int len) { - const char *p = fdt_offset_ptr(fdt, offset, len+1); + const char *p = fdt_offset_ptr(fdt, offset + FDT_TAGSIZE, len+1); if (! p) /* short match */ @@ -84,12 +77,12 @@ static int nodename_eq(const void *fdt, int offset, const char *fdt_string(const void *fdt, int stroffset) { - return (char *)fdt + fdt_off_dt_strings(fdt) + stroffset; + return (const char *)fdt + fdt_off_dt_strings(fdt) + stroffset; } int fdt_get_mem_rsv(const void *fdt, int n, uint64_t *address, uint64_t *size) { - CHECK_HEADER(fdt); + FDT_CHECK_HEADER(fdt); *address = fdt64_to_cpu(_fdt_mem_rsv(fdt, n)->address); *size = fdt64_to_cpu(_fdt_mem_rsv(fdt, n)->size); return 0; @@ -104,50 +97,24 @@ int fdt_num_mem_rsv(const void *fdt) return i; } -int fdt_subnode_offset_namelen(const void *fdt, int parentoffset, +int fdt_subnode_offset_namelen(const void *fdt, int offset, const char *name, int namelen) { - int level = 0; - uint32_t tag; - int offset, nextoffset; - - CHECK_HEADER(fdt); - - tag = fdt_next_tag(fdt, parentoffset, &nextoffset); - if (tag != FDT_BEGIN_NODE) - return -FDT_ERR_BADOFFSET; - - do { - offset = nextoffset; - tag = fdt_next_tag(fdt, offset, &nextoffset); - - switch (tag) { - case FDT_END: - return -FDT_ERR_TRUNCATED; - - case FDT_BEGIN_NODE: - level++; - if (level != 1) - continue; - if (nodename_eq(fdt, offset+FDT_TAGSIZE, name, namelen)) - /* Found it! */ - return offset; - break; - - case FDT_END_NODE: - level--; - break; + int depth; - case FDT_PROP: - case FDT_NOP: - break; + FDT_CHECK_HEADER(fdt); - default: - return -FDT_ERR_BADSTRUCTURE; - } - } while (level >= 0); + for (depth = 0; + offset >= 0; + offset = fdt_next_node(fdt, offset, &depth)) { + if (depth < 0) + return -FDT_ERR_NOTFOUND; + else if ((depth == 1) + && _fdt_nodename_eq(fdt, offset, name, namelen)) + return offset; + } - return -FDT_ERR_NOTFOUND; + return offset; /* error */ } int fdt_subnode_offset(const void *fdt, int parentoffset, @@ -162,7 +129,7 @@ int fdt_path_offset(const void *fdt, const char *path) const char *p = path; int offset = 0; - CHECK_HEADER(fdt); + FDT_CHECK_HEADER(fdt); if (*path != '/') return -FDT_ERR_BADPATH; @@ -190,16 +157,12 @@ int fdt_path_offset(const void *fdt, const char *path) const char *fdt_get_name(const void *fdt, int nodeoffset, int *len) { - const struct fdt_node_header *nh; + const struct fdt_node_header *nh = _fdt_offset_ptr(fdt, nodeoffset); int err; - if ((err = fdt_check_header(fdt)) != 0) - goto fail; - - err = -FDT_ERR_BADOFFSET; - nh = fdt_offset_ptr(fdt, nodeoffset, sizeof(*nh)); - if (!nh || (fdt32_to_cpu(nh->tag) != FDT_BEGIN_NODE)) - goto fail; + if (((err = fdt_check_header(fdt)) != 0) + || ((err = _fdt_check_node_offset(fdt, nodeoffset)) < 0)) + goto fail; if (len) *len = strlen(nh->name); @@ -222,17 +185,11 @@ const struct fdt_property *fdt_get_property(const void *fdt, int offset, nextoffset; int err; - if ((err = fdt_check_header(fdt)) != 0) - goto fail; - - err = -FDT_ERR_BADOFFSET; - if (nodeoffset % FDT_TAGSIZE) - goto fail; - - tag = fdt_next_tag(fdt, nodeoffset, &nextoffset); - if (tag != FDT_BEGIN_NODE) - goto fail; + if (((err = fdt_check_header(fdt)) != 0) + || ((err = _fdt_check_node_offset(fdt, nodeoffset)) < 0)) + goto fail; + nextoffset = err; do { offset = nextoffset; @@ -253,7 +210,7 @@ const struct fdt_property *fdt_get_property(const void *fdt, if (! prop) goto fail; namestroff = fdt32_to_cpu(prop->nameoff); - if (streq(fdt_string(fdt, namestroff), name)) { + if (strcmp(fdt_string(fdt, namestroff), name) == 0) { /* Found it! */ int len = fdt32_to_cpu(prop->len); prop = fdt_offset_ptr(fdt, offset, @@ -307,115 +264,91 @@ uint32_t fdt_get_phandle(const void *fdt, int nodeoffset) int fdt_get_path(const void *fdt, int nodeoffset, char *buf, int buflen) { - uint32_t tag; - int p = 0, overflow = 0; - int offset, nextoffset, namelen; + int pdepth = 0, p = 0; + int offset, depth, namelen; const char *name; - CHECK_HEADER(fdt); - - tag = fdt_next_tag(fdt, 0, &nextoffset); - if (tag != FDT_BEGIN_NODE) - return -FDT_ERR_BADSTRUCTURE; + FDT_CHECK_HEADER(fdt); if (buflen < 2) return -FDT_ERR_NOSPACE; - buf[0] = '/'; - p = 1; - while (nextoffset <= nodeoffset) { - offset = nextoffset; - tag = fdt_next_tag(fdt, offset, &nextoffset); - switch (tag) { - case FDT_END: - return -FDT_ERR_BADOFFSET; + for (offset = 0, depth = 0; + (offset >= 0) && (offset <= nodeoffset); + offset = fdt_next_node(fdt, offset, &depth)) { + if (pdepth < depth) + continue; /* overflowed buffer */ - case FDT_BEGIN_NODE: - name = fdt_get_name(fdt, offset, &namelen); - if (!name) - return namelen; - if (overflow || ((p + namelen + 1) > buflen)) { - overflow++; - break; - } + while (pdepth > depth) { + do { + p--; + } while (buf[p-1] != '/'); + pdepth--; + } + + name = fdt_get_name(fdt, offset, &namelen); + if (!name) + return namelen; + if ((p + namelen + 1) <= buflen) { memcpy(buf + p, name, namelen); p += namelen; buf[p++] = '/'; - break; - - case FDT_END_NODE: - if (overflow) { - overflow--; - break; - } - do { - p--; - } while (buf[p-1] != '/'); - break; + pdepth++; + } - case FDT_PROP: - case FDT_NOP: - break; + if (offset == nodeoffset) { + if (pdepth < (depth + 1)) + return -FDT_ERR_NOSPACE; - default: - return -FDT_ERR_BADSTRUCTURE; + if (p > 1) /* special case so that root path is "/", not "" */ + p--; + buf[p] = '\0'; + return p; } } - if (overflow) - return -FDT_ERR_NOSPACE; + if ((offset == -FDT_ERR_NOTFOUND) || (offset >= 0)) + return -FDT_ERR_BADOFFSET; + else if (offset == -FDT_ERR_BADOFFSET) + return -FDT_ERR_BADSTRUCTURE; - if (p > 1) /* special case so that root path is "/", not "" */ - p--; - buf[p] = '\0'; - return p; + return offset; /* error from fdt_next_node() */ } int fdt_supernode_atdepth_offset(const void *fdt, int nodeoffset, int supernodedepth, int *nodedepth) { - int level = -1; - uint32_t tag; - int offset, nextoffset = 0; + int offset, depth; int supernodeoffset = -FDT_ERR_INTERNAL; - CHECK_HEADER(fdt); + FDT_CHECK_HEADER(fdt); if (supernodedepth < 0) return -FDT_ERR_NOTFOUND; - do { - offset = nextoffset; - tag = fdt_next_tag(fdt, offset, &nextoffset); - switch (tag) { - case FDT_END: - return -FDT_ERR_BADOFFSET; - - case FDT_BEGIN_NODE: - level++; - if (level == supernodedepth) - supernodeoffset = offset; - break; - - case FDT_END_NODE: - level--; - break; + for (offset = 0, depth = 0; + (offset >= 0) && (offset <= nodeoffset); + offset = fdt_next_node(fdt, offset, &depth)) { + if (depth == supernodedepth) + supernodeoffset = offset; - case FDT_PROP: - case FDT_NOP: - break; + if (offset == nodeoffset) { + if (nodedepth) + *nodedepth = depth; - default: - return -FDT_ERR_BADSTRUCTURE; + if (supernodedepth > depth) + return -FDT_ERR_NOTFOUND; + else + return supernodeoffset; } - } while (offset < nodeoffset); + } - if (nodedepth) - *nodedepth = level; + if ((offset == -FDT_ERR_NOTFOUND) || (offset >= 0)) + return -FDT_ERR_BADOFFSET; + else if (offset == -FDT_ERR_BADOFFSET) + return -FDT_ERR_BADSTRUCTURE; - if (supernodedepth > level) - return -FDT_ERR_NOTFOUND; - return supernodeoffset; + return offset; /* error from fdt_next_node() */ } int fdt_node_depth(const void *fdt, int nodeoffset) @@ -443,51 +376,27 @@ int fdt_node_offset_by_prop_value(const void *fdt, int startoffset, const char *propname, const void *propval, int proplen) { - uint32_t tag; - int offset, nextoffset; + int offset; const void *val; int len; - CHECK_HEADER(fdt); - - if (startoffset >= 0) { - tag = fdt_next_tag(fdt, startoffset, &nextoffset); - if (tag != FDT_BEGIN_NODE) - return -FDT_ERR_BADOFFSET; - } else { - nextoffset = 0; - } + FDT_CHECK_HEADER(fdt); /* FIXME: The algorithm here is pretty horrible: we scan each * property of a node in fdt_getprop(), then if that didn't * find what we want, we scan over them again making our way * to the next node. Still it's the easiest to implement * approach; performance can come later. */ - do { - offset = nextoffset; - tag = fdt_next_tag(fdt, offset, &nextoffset); - - switch (tag) { - case FDT_BEGIN_NODE: - val = fdt_getprop(fdt, offset, propname, &len); - if (val - && (len == proplen) - && (memcmp(val, propval, len) == 0)) - return offset; - break; - - case FDT_PROP: - case FDT_END: - case FDT_END_NODE: - case FDT_NOP: - break; - - default: - return -FDT_ERR_BADSTRUCTURE; - } - } while (tag != FDT_END); + for (offset = fdt_next_node(fdt, startoffset, NULL); + offset >= 0; + offset = fdt_next_node(fdt, offset, NULL)) { + val = fdt_getprop(fdt, offset, propname, &len); + if (val && (len == proplen) + && (memcmp(val, propval, len) == 0)) + return offset; + } - return -FDT_ERR_NOTFOUND; + return offset; /* error from fdt_next_node() */ } int fdt_node_offset_by_phandle(const void *fdt, uint32_t phandle) @@ -499,10 +408,10 @@ int fdt_node_offset_by_phandle(const void *fdt, uint32_t phandle) &phandle, sizeof(phandle)); } -int _stringlist_contains(const void *strlist, int listlen, const char *str) +int _stringlist_contains(const char *strlist, int listlen, const char *str) { int len = strlen(str); - const void *p; + const char *p; while (listlen >= len) { if (memcmp(str, strlist, len+1) == 0) @@ -534,50 +443,24 @@ int fdt_node_check_compatible(const void *fdt, int nodeoffset, int fdt_node_offset_by_compatible(const void *fdt, int startoffset, const char *compatible) { - uint32_t tag; - int offset, nextoffset; - int err; - - CHECK_HEADER(fdt); + int offset, err; - if (startoffset >= 0) { - tag = fdt_next_tag(fdt, startoffset, &nextoffset); - if (tag != FDT_BEGIN_NODE) - return -FDT_ERR_BADOFFSET; - } else { - nextoffset = 0; - } + FDT_CHECK_HEADER(fdt); /* FIXME: The algorithm here is pretty horrible: we scan each * property of a node in fdt_node_check_compatible(), then if * that didn't find what we want, we scan over them again * making our way to the next node. Still it's the easiest to * implement approach; performance can come later. */ - do { - offset = nextoffset; - tag = fdt_next_tag(fdt, offset, &nextoffset); - - switch (tag) { - case FDT_BEGIN_NODE: - err = fdt_node_check_compatible(fdt, offset, - compatible); - if ((err < 0) - && (err != -FDT_ERR_NOTFOUND)) - return err; - else if (err == 0) - return offset; - break; - - case FDT_PROP: - case FDT_END: - case FDT_END_NODE: - case FDT_NOP: - break; - - default: - return -FDT_ERR_BADSTRUCTURE; - } - } while (tag != FDT_END); + for (offset = fdt_next_node(fdt, startoffset, NULL); + offset >= 0; + offset = fdt_next_node(fdt, offset, NULL)) { + err = fdt_node_check_compatible(fdt, offset, compatible); + if ((err < 0) && (err != -FDT_ERR_NOTFOUND)) + return err; + else if (err == 0) + return offset; + } - return -FDT_ERR_NOTFOUND; + return offset; /* error from fdt_next_node() */ } diff --git a/arch/powerpc/boot/libfdt/fdt_rw.c b/arch/powerpc/boot/libfdt/fdt_rw.c index 6673f8ec962..8e7ec4cb7bc 100644 --- a/arch/powerpc/boot/libfdt/fdt_rw.c +++ b/arch/powerpc/boot/libfdt/fdt_rw.c @@ -55,10 +55,10 @@ #include "libfdt_internal.h" -static int _blocks_misordered(const void *fdt, +static int _fdt_blocks_misordered(const void *fdt, int mem_rsv_size, int struct_size) { - return (fdt_off_mem_rsvmap(fdt) < ALIGN(sizeof(struct fdt_header), 8)) + return (fdt_off_mem_rsvmap(fdt) < FDT_ALIGN(sizeof(struct fdt_header), 8)) || (fdt_off_dt_struct(fdt) < (fdt_off_mem_rsvmap(fdt) + mem_rsv_size)) || (fdt_off_dt_strings(fdt) < @@ -67,16 +67,14 @@ static int _blocks_misordered(const void *fdt, (fdt_off_dt_strings(fdt) + fdt_size_dt_strings(fdt))); } -static int rw_check_header(void *fdt) +static int _fdt_rw_check_header(void *fdt) { - int err; + FDT_CHECK_HEADER(fdt); - if ((err = fdt_check_header(fdt))) - return err; if (fdt_version(fdt) < 17) return -FDT_ERR_BADVERSION; - if (_blocks_misordered(fdt, sizeof(struct fdt_reserve_entry), - fdt_size_dt_struct(fdt))) + if (_fdt_blocks_misordered(fdt, sizeof(struct fdt_reserve_entry), + fdt_size_dt_struct(fdt))) return -FDT_ERR_BADLAYOUT; if (fdt_version(fdt) > 17) fdt_set_version(fdt, 17); @@ -84,36 +82,37 @@ static int rw_check_header(void *fdt) return 0; } -#define RW_CHECK_HEADER(fdt) \ +#define FDT_RW_CHECK_HEADER(fdt) \ { \ int err; \ - if ((err = rw_check_header(fdt)) != 0) \ + if ((err = _fdt_rw_check_header(fdt)) != 0) \ return err; \ } -static inline int _blob_data_size(void *fdt) +static inline int _fdt_data_size(void *fdt) { return fdt_off_dt_strings(fdt) + fdt_size_dt_strings(fdt); } -static int _blob_splice(void *fdt, void *p, int oldlen, int newlen) +static int _fdt_splice(void *fdt, void *splicepoint, int oldlen, int newlen) { - void *end = fdt + _blob_data_size(fdt); + char *p = splicepoint; + char *end = (char *)fdt + _fdt_data_size(fdt); if (((p + oldlen) < p) || ((p + oldlen) > end)) return -FDT_ERR_BADOFFSET; - if ((end - oldlen + newlen) > (fdt + fdt_totalsize(fdt))) + if ((end - oldlen + newlen) > ((char *)fdt + fdt_totalsize(fdt))) return -FDT_ERR_NOSPACE; memmove(p + newlen, p + oldlen, end - p - oldlen); return 0; } -static int _blob_splice_mem_rsv(void *fdt, struct fdt_reserve_entry *p, - int oldn, int newn) +static int _fdt_splice_mem_rsv(void *fdt, struct fdt_reserve_entry *p, + int oldn, int newn) { int delta = (newn - oldn) * sizeof(*p); int err; - err = _blob_splice(fdt, p, oldn * sizeof(*p), newn * sizeof(*p)); + err = _fdt_splice(fdt, p, oldn * sizeof(*p), newn * sizeof(*p)); if (err) return err; fdt_set_off_dt_struct(fdt, fdt_off_dt_struct(fdt) + delta); @@ -121,13 +120,13 @@ static int _blob_splice_mem_rsv(void *fdt, struct fdt_reserve_entry *p, return 0; } -static int _blob_splice_struct(void *fdt, void *p, - int oldlen, int newlen) +static int _fdt_splice_struct(void *fdt, void *p, + int oldlen, int newlen) { int delta = newlen - oldlen; int err; - if ((err = _blob_splice(fdt, p, oldlen, newlen))) + if ((err = _fdt_splice(fdt, p, oldlen, newlen))) return err; fdt_set_size_dt_struct(fdt, fdt_size_dt_struct(fdt) + delta); @@ -135,19 +134,20 @@ static int _blob_splice_struct(void *fdt, void *p, return 0; } -static int _blob_splice_string(void *fdt, int newlen) +static int _fdt_splice_string(void *fdt, int newlen) { - void *p = fdt + fdt_off_dt_strings(fdt) + fdt_size_dt_strings(fdt); + void *p = (char *)fdt + + fdt_off_dt_strings(fdt) + fdt_size_dt_strings(fdt); int err; - if ((err = _blob_splice(fdt, p, 0, newlen))) + if ((err = _fdt_splice(fdt, p, 0, newlen))) return err; fdt_set_size_dt_strings(fdt, fdt_size_dt_strings(fdt) + newlen); return 0; } -static int _find_add_string(void *fdt, const char *s) +static int _fdt_find_add_string(void *fdt, const char *s) { char *strtab = (char *)fdt + fdt_off_dt_strings(fdt); const char *p; @@ -161,7 +161,7 @@ static int _find_add_string(void *fdt, const char *s) return (p - strtab); new = strtab + fdt_size_dt_strings(fdt); - err = _blob_splice_string(fdt, len); + err = _fdt_splice_string(fdt, len); if (err) return err; @@ -174,11 +174,10 @@ int fdt_add_mem_rsv(void *fdt, uint64_t address, uint64_t size) struct fdt_reserve_entry *re; int err; - if ((err = rw_check_header(fdt))) - return err; + FDT_RW_CHECK_HEADER(fdt); re = _fdt_mem_rsv_w(fdt, fdt_num_mem_rsv(fdt)); - err = _blob_splice_mem_rsv(fdt, re, 0, 1); + err = _fdt_splice_mem_rsv(fdt, re, 0, 1); if (err) return err; @@ -192,19 +191,19 @@ int fdt_del_mem_rsv(void *fdt, int n) struct fdt_reserve_entry *re = _fdt_mem_rsv_w(fdt, n); int err; - if ((err = rw_check_header(fdt))) - return err; + FDT_RW_CHECK_HEADER(fdt); + if (n >= fdt_num_mem_rsv(fdt)) return -FDT_ERR_NOTFOUND; - err = _blob_splice_mem_rsv(fdt, re, 1, 0); + err = _fdt_splice_mem_rsv(fdt, re, 1, 0); if (err) return err; return 0; } -static int _resize_property(void *fdt, int nodeoffset, const char *name, int len, - struct fdt_property **prop) +static int _fdt_resize_property(void *fdt, int nodeoffset, const char *name, + int len, struct fdt_property **prop) { int oldlen; int err; @@ -213,36 +212,33 @@ static int _resize_property(void *fdt, int nodeoffset, const char *name, int len if (! (*prop)) return oldlen; - if ((err = _blob_splice_struct(fdt, (*prop)->data, - ALIGN(oldlen, FDT_TAGSIZE), - ALIGN(len, FDT_TAGSIZE)))) + if ((err = _fdt_splice_struct(fdt, (*prop)->data, FDT_TAGALIGN(oldlen), + FDT_TAGALIGN(len)))) return err; (*prop)->len = cpu_to_fdt32(len); return 0; } -static int _add_property(void *fdt, int nodeoffset, const char *name, int len, - struct fdt_property **prop) +static int _fdt_add_property(void *fdt, int nodeoffset, const char *name, + int len, struct fdt_property **prop) { - uint32_t tag; int proplen; int nextoffset; int namestroff; int err; - tag = fdt_next_tag(fdt, nodeoffset, &nextoffset); - if (tag != FDT_BEGIN_NODE) - return -FDT_ERR_BADOFFSET; + if ((nextoffset = _fdt_check_node_offset(fdt, nodeoffset)) < 0) + return nextoffset; - namestroff = _find_add_string(fdt, name); + namestroff = _fdt_find_add_string(fdt, name); if (namestroff < 0) return namestroff; *prop = _fdt_offset_ptr_w(fdt, nextoffset); - proplen = sizeof(**prop) + ALIGN(len, FDT_TAGSIZE); + proplen = sizeof(**prop) + FDT_TAGALIGN(len); - err = _blob_splice_struct(fdt, *prop, 0, proplen); + err = _fdt_splice_struct(fdt, *prop, 0, proplen); if (err) return err; @@ -252,18 +248,40 @@ static int _add_property(void *fdt, int nodeoffset, const char *name, int len, return 0; } +int fdt_set_name(void *fdt, int nodeoffset, const char *name) +{ + char *namep; + int oldlen, newlen; + int err; + + FDT_RW_CHECK_HEADER(fdt); + + namep = (char *)(uintptr_t)fdt_get_name(fdt, nodeoffset, &oldlen); + if (!namep) + return oldlen; + + newlen = strlen(name); + + err = _fdt_splice_struct(fdt, namep, FDT_TAGALIGN(oldlen+1), + FDT_TAGALIGN(newlen+1)); + if (err) + return err; + + memcpy(namep, name, newlen+1); + return 0; +} + int fdt_setprop(void *fdt, int nodeoffset, const char *name, const void *val, int len) { struct fdt_property *prop; int err; - if ((err = rw_check_header(fdt))) - return err; + FDT_RW_CHECK_HEADER(fdt); - err = _resize_property(fdt, nodeoffset, name, len, &prop); + err = _fdt_resize_property(fdt, nodeoffset, name, len, &prop); if (err == -FDT_ERR_NOTFOUND) - err = _add_property(fdt, nodeoffset, name, len, &prop); + err = _fdt_add_property(fdt, nodeoffset, name, len, &prop); if (err) return err; @@ -276,14 +294,14 @@ int fdt_delprop(void *fdt, int nodeoffset, const char *name) struct fdt_property *prop; int len, proplen; - RW_CHECK_HEADER(fdt); + FDT_RW_CHECK_HEADER(fdt); prop = fdt_get_property_w(fdt, nodeoffset, name, &len); if (! prop) return len; - proplen = sizeof(*prop) + ALIGN(len, FDT_TAGSIZE); - return _blob_splice_struct(fdt, prop, proplen, 0); + proplen = sizeof(*prop) + FDT_TAGALIGN(len); + return _fdt_splice_struct(fdt, prop, proplen, 0); } int fdt_add_subnode_namelen(void *fdt, int parentoffset, @@ -296,7 +314,7 @@ int fdt_add_subnode_namelen(void *fdt, int parentoffset, uint32_t tag; uint32_t *endtag; - RW_CHECK_HEADER(fdt); + FDT_RW_CHECK_HEADER(fdt); offset = fdt_subnode_offset_namelen(fdt, parentoffset, name, namelen); if (offset >= 0) @@ -309,19 +327,19 @@ int fdt_add_subnode_namelen(void *fdt, int parentoffset, do { offset = nextoffset; tag = fdt_next_tag(fdt, offset, &nextoffset); - } while (tag == FDT_PROP); + } while ((tag == FDT_PROP) || (tag == FDT_NOP)); nh = _fdt_offset_ptr_w(fdt, offset); - nodelen = sizeof(*nh) + ALIGN(namelen+1, FDT_TAGSIZE) + FDT_TAGSIZE; + nodelen = sizeof(*nh) + FDT_TAGALIGN(namelen+1) + FDT_TAGSIZE; - err = _blob_splice_struct(fdt, nh, 0, nodelen); + err = _fdt_splice_struct(fdt, nh, 0, nodelen); if (err) return err; nh->tag = cpu_to_fdt32(FDT_BEGIN_NODE); - memset(nh->name, 0, ALIGN(namelen+1, FDT_TAGSIZE)); + memset(nh->name, 0, FDT_TAGALIGN(namelen+1)); memcpy(nh->name, name, namelen); - endtag = (uint32_t *)((void *)nh + nodelen - FDT_TAGSIZE); + endtag = (uint32_t *)((char *)nh + nodelen - FDT_TAGSIZE); *endtag = cpu_to_fdt32(FDT_END_NODE); return offset; @@ -336,36 +354,36 @@ int fdt_del_node(void *fdt, int nodeoffset) { int endoffset; - RW_CHECK_HEADER(fdt); + FDT_RW_CHECK_HEADER(fdt); endoffset = _fdt_node_end_offset(fdt, nodeoffset); if (endoffset < 0) return endoffset; - return _blob_splice_struct(fdt, _fdt_offset_ptr_w(fdt, nodeoffset), - endoffset - nodeoffset, 0); + return _fdt_splice_struct(fdt, _fdt_offset_ptr_w(fdt, nodeoffset), + endoffset - nodeoffset, 0); } -static void _packblocks(const void *fdt, void *buf, - int mem_rsv_size, int struct_size) +static void _fdt_packblocks(const char *old, char *new, + int mem_rsv_size, int struct_size) { int mem_rsv_off, struct_off, strings_off; - mem_rsv_off = ALIGN(sizeof(struct fdt_header), 8); + mem_rsv_off = FDT_ALIGN(sizeof(struct fdt_header), 8); struct_off = mem_rsv_off + mem_rsv_size; strings_off = struct_off + struct_size; - memmove(buf + mem_rsv_off, fdt + fdt_off_mem_rsvmap(fdt), mem_rsv_size); - fdt_set_off_mem_rsvmap(buf, mem_rsv_off); + memmove(new + mem_rsv_off, old + fdt_off_mem_rsvmap(old), mem_rsv_size); + fdt_set_off_mem_rsvmap(new, mem_rsv_off); - memmove(buf + struct_off, fdt + fdt_off_dt_struct(fdt), struct_size); - fdt_set_off_dt_struct(buf, struct_off); - fdt_set_size_dt_struct(buf, struct_size); + memmove(new + struct_off, old + fdt_off_dt_struct(old), struct_size); + fdt_set_off_dt_struct(new, struct_off); + fdt_set_size_dt_struct(new, struct_size); - memmove(buf + strings_off, fdt + fdt_off_dt_strings(fdt), - fdt_size_dt_strings(fdt)); - fdt_set_off_dt_strings(buf, strings_off); - fdt_set_size_dt_strings(buf, fdt_size_dt_strings(fdt)); + memmove(new + strings_off, old + fdt_off_dt_strings(old), + fdt_size_dt_strings(old)); + fdt_set_off_dt_strings(new, strings_off); + fdt_set_size_dt_strings(new, fdt_size_dt_strings(old)); } int fdt_open_into(const void *fdt, void *buf, int bufsize) @@ -373,11 +391,11 @@ int fdt_open_into(const void *fdt, void *buf, int bufsize) int err; int mem_rsv_size, struct_size; int newsize; - void *tmp; + const char *fdtstart = fdt; + const char *fdtend = fdtstart + fdt_totalsize(fdt); + char *tmp; - err = fdt_check_header(fdt); - if (err) - return err; + FDT_CHECK_HEADER(fdt); mem_rsv_size = (fdt_num_mem_rsv(fdt)+1) * sizeof(struct fdt_reserve_entry); @@ -390,7 +408,7 @@ int fdt_open_into(const void *fdt, void *buf, int bufsize) ; } - if (!_blocks_misordered(fdt, mem_rsv_size, struct_size)) { + if (!_fdt_blocks_misordered(fdt, mem_rsv_size, struct_size)) { /* no further work necessary */ err = fdt_move(fdt, buf, bufsize); if (err) @@ -402,22 +420,23 @@ int fdt_open_into(const void *fdt, void *buf, int bufsize) } /* Need to reorder */ - newsize = ALIGN(sizeof(struct fdt_header), 8) + mem_rsv_size + newsize = FDT_ALIGN(sizeof(struct fdt_header), 8) + mem_rsv_size + struct_size + fdt_size_dt_strings(fdt); if (bufsize < newsize) return -FDT_ERR_NOSPACE; - if (((buf + newsize) <= fdt) - || (buf >= (fdt + fdt_totalsize(fdt)))) { - tmp = buf; - } else { - tmp = (void *)fdt + fdt_totalsize(fdt); - if ((tmp + newsize) > (buf + bufsize)) + /* First attempt to build converted tree at beginning of buffer */ + tmp = buf; + /* But if that overlaps with the old tree... */ + if (((tmp + newsize) > fdtstart) && (tmp < fdtend)) { + /* Try right after the old tree instead */ + tmp = (char *)(uintptr_t)fdtend; + if ((tmp + newsize) > ((char *)buf + bufsize)) return -FDT_ERR_NOSPACE; } - _packblocks(fdt, tmp, mem_rsv_size, struct_size); + _fdt_packblocks(fdt, tmp, mem_rsv_size, struct_size); memmove(buf, tmp, newsize); fdt_set_magic(buf, FDT_MAGIC); @@ -432,16 +451,13 @@ int fdt_open_into(const void *fdt, void *buf, int bufsize) int fdt_pack(void *fdt) { int mem_rsv_size; - int err; - err = rw_check_header(fdt); - if (err) - return err; + FDT_RW_CHECK_HEADER(fdt); mem_rsv_size = (fdt_num_mem_rsv(fdt)+1) * sizeof(struct fdt_reserve_entry); - _packblocks(fdt, fdt, mem_rsv_size, fdt_size_dt_struct(fdt)); - fdt_set_totalsize(fdt, _blob_data_size(fdt)); + _fdt_packblocks(fdt, fdt, mem_rsv_size, fdt_size_dt_struct(fdt)); + fdt_set_totalsize(fdt, _fdt_data_size(fdt)); return 0; } diff --git a/arch/powerpc/boot/libfdt/fdt_strerror.c b/arch/powerpc/boot/libfdt/fdt_strerror.c index f9d32ef5360..e6c3ceee8c5 100644 --- a/arch/powerpc/boot/libfdt/fdt_strerror.c +++ b/arch/powerpc/boot/libfdt/fdt_strerror.c @@ -55,29 +55,29 @@ #include "libfdt_internal.h" -struct errtabent { +struct fdt_errtabent { const char *str; }; -#define ERRTABENT(val) \ +#define FDT_ERRTABENT(val) \ [(val)] = { .str = #val, } -static struct errtabent errtable[] = { - ERRTABENT(FDT_ERR_NOTFOUND), - ERRTABENT(FDT_ERR_EXISTS), - ERRTABENT(FDT_ERR_NOSPACE), +static struct fdt_errtabent fdt_errtable[] = { + FDT_ERRTABENT(FDT_ERR_NOTFOUND), + FDT_ERRTABENT(FDT_ERR_EXISTS), + FDT_ERRTABENT(FDT_ERR_NOSPACE), - ERRTABENT(FDT_ERR_BADOFFSET), - ERRTABENT(FDT_ERR_BADPATH), - ERRTABENT(FDT_ERR_BADSTATE), + FDT_ERRTABENT(FDT_ERR_BADOFFSET), + FDT_ERRTABENT(FDT_ERR_BADPATH), + FDT_ERRTABENT(FDT_ERR_BADSTATE), - ERRTABENT(FDT_ERR_TRUNCATED), - ERRTABENT(FDT_ERR_BADMAGIC), - ERRTABENT(FDT_ERR_BADVERSION), - ERRTABENT(FDT_ERR_BADSTRUCTURE), - ERRTABENT(FDT_ERR_BADLAYOUT), + FDT_ERRTABENT(FDT_ERR_TRUNCATED), + FDT_ERRTABENT(FDT_ERR_BADMAGIC), + FDT_ERRTABENT(FDT_ERR_BADVERSION), + FDT_ERRTABENT(FDT_ERR_BADSTRUCTURE), + FDT_ERRTABENT(FDT_ERR_BADLAYOUT), }; -#define ERRTABSIZE (sizeof(errtable) / sizeof(errtable[0])) +#define FDT_ERRTABSIZE (sizeof(fdt_errtable) / sizeof(fdt_errtable[0])) const char *fdt_strerror(int errval) { @@ -85,8 +85,8 @@ const char *fdt_strerror(int errval) return ""; else if (errval == 0) return ""; - else if (errval > -ERRTABSIZE) { - const char *s = errtable[-errval].str; + else if (errval > -FDT_ERRTABSIZE) { + const char *s = fdt_errtable[-errval].str; if (s) return s; diff --git a/arch/powerpc/boot/libfdt/fdt_sw.c b/arch/powerpc/boot/libfdt/fdt_sw.c index dda2de34b2e..698329e0cca 100644 --- a/arch/powerpc/boot/libfdt/fdt_sw.c +++ b/arch/powerpc/boot/libfdt/fdt_sw.c @@ -55,14 +55,22 @@ #include "libfdt_internal.h" -static int check_header_sw(void *fdt) +static int _fdt_sw_check_header(void *fdt) { - if (fdt_magic(fdt) != SW_MAGIC) + if (fdt_magic(fdt) != FDT_SW_MAGIC) return -FDT_ERR_BADMAGIC; + /* FIXME: should check more details about the header state */ return 0; } -static void *grab_space(void *fdt, int len) +#define FDT_SW_CHECK_HEADER(fdt) \ + { \ + int err; \ + if ((err = _fdt_sw_check_header(fdt)) != 0) \ + return err; \ + } + +static void *_fdt_grab_space(void *fdt, int len) { int offset = fdt_size_dt_struct(fdt); int spaceleft; @@ -86,13 +94,13 @@ int fdt_create(void *buf, int bufsize) memset(buf, 0, bufsize); - fdt_set_magic(fdt, SW_MAGIC); + fdt_set_magic(fdt, FDT_SW_MAGIC); fdt_set_version(fdt, FDT_LAST_SUPPORTED_VERSION); fdt_set_last_comp_version(fdt, FDT_FIRST_SUPPORTED_VERSION); fdt_set_totalsize(fdt, bufsize); - fdt_set_off_mem_rsvmap(fdt, ALIGN(sizeof(struct fdt_header), - sizeof(struct fdt_reserve_entry))); + fdt_set_off_mem_rsvmap(fdt, FDT_ALIGN(sizeof(struct fdt_header), + sizeof(struct fdt_reserve_entry))); fdt_set_off_dt_struct(fdt, fdt_off_mem_rsvmap(fdt)); fdt_set_off_dt_strings(fdt, bufsize); @@ -102,11 +110,10 @@ int fdt_create(void *buf, int bufsize) int fdt_add_reservemap_entry(void *fdt, uint64_t addr, uint64_t size) { struct fdt_reserve_entry *re; - int err = check_header_sw(fdt); int offset; - if (err) - return err; + FDT_SW_CHECK_HEADER(fdt); + if (fdt_size_dt_struct(fdt)) return -FDT_ERR_BADSTATE; @@ -114,7 +121,7 @@ int fdt_add_reservemap_entry(void *fdt, uint64_t addr, uint64_t size) if ((offset + sizeof(*re)) > fdt_totalsize(fdt)) return -FDT_ERR_NOSPACE; - re = (struct fdt_reserve_entry *)(fdt + offset); + re = (struct fdt_reserve_entry *)((char *)fdt + offset); re->address = cpu_to_fdt64(addr); re->size = cpu_to_fdt64(size); @@ -131,13 +138,11 @@ int fdt_finish_reservemap(void *fdt) int fdt_begin_node(void *fdt, const char *name) { struct fdt_node_header *nh; - int err = check_header_sw(fdt); int namelen = strlen(name) + 1; - if (err) - return err; + FDT_SW_CHECK_HEADER(fdt); - nh = grab_space(fdt, sizeof(*nh) + ALIGN(namelen, FDT_TAGSIZE)); + nh = _fdt_grab_space(fdt, sizeof(*nh) + FDT_TAGALIGN(namelen)); if (! nh) return -FDT_ERR_NOSPACE; @@ -149,12 +154,10 @@ int fdt_begin_node(void *fdt, const char *name) int fdt_end_node(void *fdt) { uint32_t *en; - int err = check_header_sw(fdt); - if (err) - return err; + FDT_SW_CHECK_HEADER(fdt); - en = grab_space(fdt, FDT_TAGSIZE); + en = _fdt_grab_space(fdt, FDT_TAGSIZE); if (! en) return -FDT_ERR_NOSPACE; @@ -162,7 +165,7 @@ int fdt_end_node(void *fdt) return 0; } -static int find_add_string(void *fdt, const char *s) +static int _fdt_find_add_string(void *fdt, const char *s) { char *strtab = (char *)fdt + fdt_totalsize(fdt); const char *p; @@ -188,17 +191,15 @@ static int find_add_string(void *fdt, const char *s) int fdt_property(void *fdt, const char *name, const void *val, int len) { struct fdt_property *prop; - int err = check_header_sw(fdt); int nameoff; - if (err) - return err; + FDT_SW_CHECK_HEADER(fdt); - nameoff = find_add_string(fdt, name); + nameoff = _fdt_find_add_string(fdt, name); if (nameoff == 0) return -FDT_ERR_NOSPACE; - prop = grab_space(fdt, sizeof(*prop) + ALIGN(len, FDT_TAGSIZE)); + prop = _fdt_grab_space(fdt, sizeof(*prop) + FDT_TAGALIGN(len)); if (! prop) return -FDT_ERR_NOSPACE; @@ -211,18 +212,16 @@ int fdt_property(void *fdt, const char *name, const void *val, int len) int fdt_finish(void *fdt) { - int err = check_header_sw(fdt); char *p = (char *)fdt; uint32_t *end; int oldstroffset, newstroffset; uint32_t tag; int offset, nextoffset; - if (err) - return err; + FDT_SW_CHECK_HEADER(fdt); /* Add terminator */ - end = grab_space(fdt, sizeof(*end)); + end = _fdt_grab_space(fdt, sizeof(*end)); if (! end) return -FDT_ERR_NOSPACE; *end = cpu_to_fdt32(FDT_END); diff --git a/arch/powerpc/boot/libfdt/fdt_wip.c b/arch/powerpc/boot/libfdt/fdt_wip.c index 88e24b8318f..a4652c6e787 100644 --- a/arch/powerpc/boot/libfdt/fdt_wip.c +++ b/arch/powerpc/boot/libfdt/fdt_wip.c @@ -72,11 +72,11 @@ int fdt_setprop_inplace(void *fdt, int nodeoffset, const char *name, return 0; } -static void nop_region(void *start, int len) +static void _fdt_nop_region(void *start, int len) { uint32_t *p; - for (p = start; (void *)p < (start + len); p++) + for (p = start; (char *)p < ((char *)start + len); p++) *p = cpu_to_fdt32(FDT_NOP); } @@ -89,7 +89,7 @@ int fdt_nop_property(void *fdt, int nodeoffset, const char *name) if (! prop) return len; - nop_region(prop, len + sizeof(*prop)); + _fdt_nop_region(prop, len + sizeof(*prop)); return 0; } @@ -139,6 +139,7 @@ int fdt_nop_node(void *fdt, int nodeoffset) if (endoffset < 0) return endoffset; - nop_region(fdt_offset_ptr_w(fdt, nodeoffset, 0), endoffset - nodeoffset); + _fdt_nop_region(fdt_offset_ptr_w(fdt, nodeoffset, 0), + endoffset - nodeoffset); return 0; } diff --git a/arch/powerpc/boot/libfdt/libfdt.h b/arch/powerpc/boot/libfdt/libfdt.h index 6b2fb92ea35..ce80e4fb41b 100644 --- a/arch/powerpc/boot/libfdt/libfdt.h +++ b/arch/powerpc/boot/libfdt/libfdt.h @@ -125,11 +125,17 @@ const void *fdt_offset_ptr(const void *fdt, int offset, int checklen); static inline void *fdt_offset_ptr_w(void *fdt, int offset, int checklen) { - return (void *)fdt_offset_ptr(fdt, offset, checklen); + return (void *)(uintptr_t)fdt_offset_ptr(fdt, offset, checklen); } uint32_t fdt_next_tag(const void *fdt, int offset, int *nextoffset); +/**********************************************************************/ +/* Traversal functions */ +/**********************************************************************/ + +int fdt_next_node(const void *fdt, int offset, int *depth); + /**********************************************************************/ /* General functions */ /**********************************************************************/ @@ -207,7 +213,7 @@ int fdt_move(const void *fdt, void *buf, int bufsize); /**********************************************************************/ /** - * fdt_string - retreive a string from the strings block of a device tree + * fdt_string - retrieve a string from the strings block of a device tree * @fdt: pointer to the device tree blob * @stroffset: offset of the string within the strings block (native endian) * @@ -221,7 +227,7 @@ int fdt_move(const void *fdt, void *buf, int bufsize); const char *fdt_string(const void *fdt, int stroffset); /** - * fdt_num_mem_rsv - retreive the number of memory reserve map entries + * fdt_num_mem_rsv - retrieve the number of memory reserve map entries * @fdt: pointer to the device tree blob * * Returns the number of entries in the device tree blob's memory @@ -234,7 +240,7 @@ const char *fdt_string(const void *fdt, int stroffset); int fdt_num_mem_rsv(const void *fdt); /** - * fdt_get_mem_rsv - retreive one memory reserve map entry + * fdt_get_mem_rsv - retrieve one memory reserve map entry * @fdt: pointer to the device tree blob * @address, @size: pointers to 64-bit variables * @@ -314,7 +320,7 @@ int fdt_subnode_offset(const void *fdt, int parentoffset, const char *name); int fdt_path_offset(const void *fdt, const char *path); /** - * fdt_get_name - retreive the name of a given node + * fdt_get_name - retrieve the name of a given node * @fdt: pointer to the device tree blob * @nodeoffset: structure block offset of the starting node * @lenp: pointer to an integer variable (will be overwritten) or NULL @@ -346,7 +352,7 @@ const char *fdt_get_name(const void *fdt, int nodeoffset, int *lenp); * fdt_get_property() retrieves a pointer to the fdt_property * structure within the device tree blob corresponding to the property * named 'name' of the node at offset nodeoffset. If lenp is - * non-NULL, the length of the property value also returned, in the + * non-NULL, the length of the property value is also returned, in the * integer pointed to by lenp. * * returns: @@ -369,8 +375,8 @@ static inline struct fdt_property *fdt_get_property_w(void *fdt, int nodeoffset, const char *name, int *lenp) { - return (struct fdt_property *)fdt_get_property(fdt, nodeoffset, - name, lenp); + return (struct fdt_property *)(uintptr_t) + fdt_get_property(fdt, nodeoffset, name, lenp); } /** @@ -383,7 +389,7 @@ static inline struct fdt_property *fdt_get_property_w(void *fdt, int nodeoffset, * fdt_getprop() retrieves a pointer to the value of the property * named 'name' of the node at offset nodeoffset (this will be a * pointer to within the device blob itself, not a copy of the value). - * If lenp is non-NULL, the length of the property value also + * If lenp is non-NULL, the length of the property value is also * returned, in the integer pointed to by lenp. * * returns: @@ -405,11 +411,11 @@ const void *fdt_getprop(const void *fdt, int nodeoffset, static inline void *fdt_getprop_w(void *fdt, int nodeoffset, const char *name, int *lenp) { - return (void *)fdt_getprop(fdt, nodeoffset, name, lenp); + return (void *)(uintptr_t)fdt_getprop(fdt, nodeoffset, name, lenp); } /** - * fdt_get_phandle - retreive the phandle of a given node + * fdt_get_phandle - retrieve the phandle of a given node * @fdt: pointer to the device tree blob * @nodeoffset: structure block offset of the node * @@ -417,7 +423,7 @@ static inline void *fdt_getprop_w(void *fdt, int nodeoffset, * structure block offset nodeoffset. * * returns: - * the phandle of the node at nodeoffset, on succes (!= 0, != -1) + * the phandle of the node at nodeoffset, on success (!= 0, != -1) * 0, if the node has no phandle, or another error occurs */ uint32_t fdt_get_phandle(const void *fdt, int nodeoffset); @@ -516,7 +522,7 @@ int fdt_node_depth(const void *fdt, int nodeoffset); * structure from the start to nodeoffset, *twice*. * * returns: - * stucture block offset of the parent of the node at nodeoffset + * structure block offset of the parent of the node at nodeoffset * (>=0), on success * -FDT_ERR_BADOFFSET, nodeoffset does not refer to a BEGIN_NODE tag * -FDT_ERR_BADMAGIC, @@ -573,7 +579,7 @@ int fdt_node_offset_by_prop_value(const void *fdt, int startoffset, * @fdt: pointer to the device tree blob * @phandle: phandle value * - * fdt_node_offset_by_prop_value() returns the offset of the node + * fdt_node_offset_by_phandle() returns the offset of the node * which has the given phandle value. If there is more than one node * in the tree with the given phandle (an invalid tree), results are * undefined. @@ -655,8 +661,65 @@ int fdt_node_offset_by_compatible(const void *fdt, int startoffset, /* Write-in-place functions */ /**********************************************************************/ +/** + * fdt_setprop_inplace - change a property's value, but not its size + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @val: pointer to data to replace the property value with + * @len: length of the property value + * + * fdt_setprop_inplace() replaces the value of a given property with + * the data in val, of length len. This function cannot change the + * size of a property, and so will only work if len is equal to the + * current length of the property. + * + * This function will alter only the bytes in the blob which contain + * the given property value, and will not alter or move any other part + * of the tree. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, if len is not equal to the property's current length + * -FDT_ERR_NOTFOUND, node does not have the named property + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_setprop_inplace(void *fdt, int nodeoffset, const char *name, const void *val, int len); + +/** + * fdt_setprop_inplace_cell - change the value of a single-cell property + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @val: cell (32-bit integer) value to replace the property with + * + * fdt_setprop_inplace_cell() replaces the value of a given property + * with the 32-bit integer cell value in val, converting val to + * big-endian if necessary. This function cannot change the size of a + * property, and so will only work if the property already exists and + * has length 4. + * + * This function will alter only the bytes in the blob which contain + * the given property value, and will not alter or move any other part + * of the tree. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, if the property's length is not equal to 4 + * -FDT_ERR_NOTFOUND, node does not have the named property + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ static inline int fdt_setprop_inplace_cell(void *fdt, int nodeoffset, const char *name, uint32_t val) { @@ -664,7 +727,54 @@ static inline int fdt_setprop_inplace_cell(void *fdt, int nodeoffset, return fdt_setprop_inplace(fdt, nodeoffset, name, &val, sizeof(val)); } +/** + * fdt_nop_property - replace a property with nop tags + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to nop + * @name: name of the property to nop + * + * fdt_nop_property() will replace a given property's representation + * in the blob with FDT_NOP tags, effectively removing it from the + * tree. + * + * This function will alter only the bytes in the blob which contain + * the property, and will not alter or move any other part of the + * tree. + * + * returns: + * 0, on success + * -FDT_ERR_NOTFOUND, node does not have the named property + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_nop_property(void *fdt, int nodeoffset, const char *name); + +/** + * fdt_nop_node - replace a node (subtree) with nop tags + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node to nop + * + * fdt_nop_node() will replace a given node's representation in the + * blob, including all its subnodes, if any, with FDT_NOP tags, + * effectively removing it from the tree. + * + * This function will alter only the bytes in the blob which contain + * the node and its properties and subnodes, and will not alter or + * move any other part of the tree. + * + * returns: + * 0, on success + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_nop_node(void *fdt, int nodeoffset); /**********************************************************************/ @@ -693,23 +803,268 @@ int fdt_finish(void *fdt); int fdt_open_into(const void *fdt, void *buf, int bufsize); int fdt_pack(void *fdt); +/** + * fdt_add_mem_rsv - add one memory reserve map entry + * @fdt: pointer to the device tree blob + * @address, @size: 64-bit values (native endian) + * + * Adds a reserve map entry to the given blob reserving a region at + * address address of length size. + * + * This function will insert data into the reserve map and will + * therefore change the indexes of some entries in the table. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new reservation entry + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_add_mem_rsv(void *fdt, uint64_t address, uint64_t size); + +/** + * fdt_del_mem_rsv - remove a memory reserve map entry + * @fdt: pointer to the device tree blob + * @n: entry to remove + * + * fdt_del_mem_rsv() removes the n-th memory reserve map entry from + * the blob. + * + * This function will delete data from the reservation table and will + * therefore change the indexes of some entries in the table. + * + * returns: + * 0, on success + * -FDT_ERR_NOTFOUND, there is no entry of the given index (i.e. there + * are less than n+1 reserve map entries) + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_del_mem_rsv(void *fdt, int n); +/** + * fdt_set_name - change the name of a given node + * @fdt: pointer to the device tree blob + * @nodeoffset: structure block offset of a node + * @name: name to give the node + * + * fdt_set_name() replaces the name (including unit address, if any) + * of the given node with the given string. NOTE: this function can't + * efficiently check if the new name is unique amongst the given + * node's siblings; results are undefined if this function is invoked + * with a name equal to one of the given node's siblings. + * + * This function may insert or delete data from the blob, and will + * therefore change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob + * to contain the new name + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, standard meanings + */ +int fdt_set_name(void *fdt, int nodeoffset, const char *name); + +/** + * fdt_setprop - create or change a property + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @val: pointer to data to set the property value to + * @len: length of the property value + * + * fdt_setprop() sets the value of the named property in the given + * node to the given value and length, creating the property if it + * does not already exist. + * + * This function may insert or delete data from the blob, and will + * therefore change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new property value + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_setprop(void *fdt, int nodeoffset, const char *name, const void *val, int len); + +/** + * fdt_setprop_cell - set a property to a single cell value + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @val: 32-bit integer value for the property (native endian) + * + * fdt_setprop_cell() sets the value of the named property in the + * given node to the given cell value (converting to big-endian if + * necessary), or creates a new property with that value if it does + * not already exist. + * + * This function may insert or delete data from the blob, and will + * therefore change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new property value + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ static inline int fdt_setprop_cell(void *fdt, int nodeoffset, const char *name, uint32_t val) { val = cpu_to_fdt32(val); return fdt_setprop(fdt, nodeoffset, name, &val, sizeof(val)); } + +/** + * fdt_setprop_string - set a property to a string value + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @str: string value for the property + * + * fdt_setprop_string() sets the value of the named property in the + * given node to the given string value (using the length of the + * string to determine the new length of the property), or creates a + * new property with that value if it does not already exist. + * + * This function may insert or delete data from the blob, and will + * therefore change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new property value + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ #define fdt_setprop_string(fdt, nodeoffset, name, str) \ fdt_setprop((fdt), (nodeoffset), (name), (str), strlen(str)+1) + +/** + * fdt_delprop - delete a property + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to nop + * @name: name of the property to nop + * + * fdt_del_property() will delete the given property. + * + * This function will delete data from the blob, and will therefore + * change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOTFOUND, node does not have the named property + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_delprop(void *fdt, int nodeoffset, const char *name); + +/** + * fdt_add_subnode_namelen - creates a new node based on substring + * @fdt: pointer to the device tree blob + * @parentoffset: structure block offset of a node + * @name: name of the subnode to locate + * @namelen: number of characters of name to consider + * + * Identical to fdt_add_subnode(), but use only the first namelen + * characters of name as the name of the new node. This is useful for + * creating subnodes based on a portion of a larger string, such as a + * full path. + */ int fdt_add_subnode_namelen(void *fdt, int parentoffset, const char *name, int namelen); + +/** + * fdt_add_subnode - creates a new node + * @fdt: pointer to the device tree blob + * @parentoffset: structure block offset of a node + * @name: name of the subnode to locate + * + * fdt_add_subnode() creates a new node as a subnode of the node at + * structure block offset parentoffset, with the given name (which + * should include the unit address, if any). + * + * This function will insert data into the blob, and will therefore + * change the offsets of some existing nodes. + + * returns: + * structure block offset of the created nodeequested subnode (>=0), on success + * -FDT_ERR_NOTFOUND, if the requested subnode does not exist + * -FDT_ERR_BADOFFSET, if parentoffset did not point to an FDT_BEGIN_NODE tag + * -FDT_ERR_EXISTS, if the node at parentoffset already has a subnode of + * the given name + * -FDT_ERR_NOSPACE, if there is insufficient free space in the + * blob to contain the new node + * -FDT_ERR_NOSPACE + * -FDT_ERR_BADLAYOUT + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings. + */ int fdt_add_subnode(void *fdt, int parentoffset, const char *name); + +/** + * fdt_del_node - delete a node (subtree) + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node to nop + * + * fdt_del_node() will remove the given node, including all its + * subnodes if any, from the blob. + * + * This function will delete data from the blob, and will therefore + * change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_del_node(void *fdt, int nodeoffset); /**********************************************************************/ diff --git a/arch/powerpc/boot/libfdt/libfdt_internal.h b/arch/powerpc/boot/libfdt/libfdt_internal.h index 1e60936beb5..46eb93e4af5 100644 --- a/arch/powerpc/boot/libfdt/libfdt_internal.h +++ b/arch/powerpc/boot/libfdt/libfdt_internal.h @@ -52,38 +52,44 @@ */ #include -#define ALIGN(x, a) (((x) + (a) - 1) & ~((a) - 1)) -#define PALIGN(p, a) ((void *)ALIGN((unsigned long)(p), (a))) +#define FDT_ALIGN(x, a) (((x) + (a) - 1) & ~((a) - 1)) +#define FDT_TAGALIGN(x) (FDT_ALIGN((x), FDT_TAGSIZE)) -#define memeq(p, q, n) (memcmp((p), (q), (n)) == 0) -#define streq(p, q) (strcmp((p), (q)) == 0) +#define FDT_CHECK_HEADER(fdt) \ + { \ + int err; \ + if ((err = fdt_check_header(fdt)) != 0) \ + return err; \ + } uint32_t _fdt_next_tag(const void *fdt, int startoffset, int *nextoffset); +int _fdt_check_node_offset(const void *fdt, int offset); const char *_fdt_find_string(const char *strtab, int tabsize, const char *s); int _fdt_node_end_offset(void *fdt, int nodeoffset); static inline const void *_fdt_offset_ptr(const void *fdt, int offset) { - return fdt + fdt_off_dt_struct(fdt) + offset; + return (const char *)fdt + fdt_off_dt_struct(fdt) + offset; } static inline void *_fdt_offset_ptr_w(void *fdt, int offset) { - return (void *)_fdt_offset_ptr(fdt, offset); + return (void *)(uintptr_t)_fdt_offset_ptr(fdt, offset); } static inline const struct fdt_reserve_entry *_fdt_mem_rsv(const void *fdt, int n) { const struct fdt_reserve_entry *rsv_table = - fdt + fdt_off_mem_rsvmap(fdt); + (const struct fdt_reserve_entry *) + ((const char *)fdt + fdt_off_mem_rsvmap(fdt)); return rsv_table + n; } static inline struct fdt_reserve_entry *_fdt_mem_rsv_w(void *fdt, int n) { - return (void *)_fdt_mem_rsv(fdt, n); + return (void *)(uintptr_t)_fdt_mem_rsv(fdt, n); } -#define SW_MAGIC (~FDT_MAGIC) +#define FDT_SW_MAGIC (~FDT_MAGIC) #endif /* _LIBFDT_INTERNAL_H */ diff --git a/arch/powerpc/boot/libfdt_env.h b/arch/powerpc/boot/libfdt_env.h index a4b0fc959ec..c89fdb1b80e 100644 --- a/arch/powerpc/boot/libfdt_env.h +++ b/arch/powerpc/boot/libfdt_env.h @@ -6,6 +6,7 @@ typedef u32 uint32_t; typedef u64 uint64_t; +typedef unsigned long uintptr_t; #define fdt16_to_cpu(x) (x) #define cpu_to_fdt16(x) (x) -- cgit v1.2.3 From 8f6ba49207199cab60a4bdf43507666b93d12e18 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Sat, 9 Aug 2008 02:34:53 +1000 Subject: powerpc: Use bcd2bin/bin2bcd This changes powerpc to use the new bcd2bin/bin2bcd functions instead of the obsolete BCD_TO_BIN/BIN_TO_BCD macros. Signed-off-by: Adrian Bunk Signed-off-by: Paul Mackerras --- arch/powerpc/platforms/chrp/time.c | 24 ++++++++++++------------ arch/powerpc/platforms/iseries/mf.c | 26 +++++++++++++------------- arch/powerpc/platforms/maple/time.c | 24 ++++++++++++------------ 3 files changed, 37 insertions(+), 37 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/chrp/time.c b/arch/powerpc/platforms/chrp/time.c index 96d1e4b3c49..054dfe5b8e7 100644 --- a/arch/powerpc/platforms/chrp/time.c +++ b/arch/powerpc/platforms/chrp/time.c @@ -94,12 +94,12 @@ int chrp_set_rtc_time(struct rtc_time *tmarg) chrp_cmos_clock_write((save_freq_select|RTC_DIV_RESET2), RTC_FREQ_SELECT); if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD) { - BIN_TO_BCD(tm.tm_sec); - BIN_TO_BCD(tm.tm_min); - BIN_TO_BCD(tm.tm_hour); - BIN_TO_BCD(tm.tm_mon); - BIN_TO_BCD(tm.tm_mday); - BIN_TO_BCD(tm.tm_year); + tm.tm_sec = bin2bcd(tm.tm_sec); + tm.tm_min = bin2bcd(tm.tm_min); + tm.tm_hour = bin2bcd(tm.tm_hour); + tm.tm_mon = bin2bcd(tm.tm_mon); + tm.tm_mday = bin2bcd(tm.tm_mday); + tm.tm_year = bin2bcd(tm.tm_year); } chrp_cmos_clock_write(tm.tm_sec,RTC_SECONDS); chrp_cmos_clock_write(tm.tm_min,RTC_MINUTES); @@ -136,12 +136,12 @@ void chrp_get_rtc_time(struct rtc_time *tm) } while (sec != chrp_cmos_clock_read(RTC_SECONDS)); if (!(chrp_cmos_clock_read(RTC_CONTROL) & RTC_DM_BINARY) || RTC_ALWAYS_BCD) { - BCD_TO_BIN(sec); - BCD_TO_BIN(min); - BCD_TO_BIN(hour); - BCD_TO_BIN(day); - BCD_TO_BIN(mon); - BCD_TO_BIN(year); + sec = bcd2bin(sec); + min = bcd2bin(min); + hour = bcd2bin(hour); + day = bcd2bin(day); + mon = bcd2bin(mon); + year = bcd2bin(year); } if (year < 70) year += 100; diff --git a/arch/powerpc/platforms/iseries/mf.c b/arch/powerpc/platforms/iseries/mf.c index 731d7b15774..3689c2413d2 100644 --- a/arch/powerpc/platforms/iseries/mf.c +++ b/arch/powerpc/platforms/iseries/mf.c @@ -722,13 +722,13 @@ static int mf_set_rtc(struct rtc_time *tm) day = tm->tm_mday; mon = tm->tm_mon + 1; - BIN_TO_BCD(sec); - BIN_TO_BCD(min); - BIN_TO_BCD(hour); - BIN_TO_BCD(mon); - BIN_TO_BCD(day); - BIN_TO_BCD(y1); - BIN_TO_BCD(y2); + sec = bin2bcd(sec); + min = bin2bcd(min); + hour = bin2bcd(hour); + mon = bin2bcd(mon); + day = bin2bcd(day); + y1 = bin2bcd(y1); + y2 = bin2bcd(y2); memset(ce_time, 0, sizeof(ce_time)); ce_time[3] = 0x41; @@ -777,12 +777,12 @@ static int rtc_set_tm(int rc, u8 *ce_msg, struct rtc_time *tm) u8 day = ce_msg[10]; u8 mon = ce_msg[11]; - BCD_TO_BIN(sec); - BCD_TO_BIN(min); - BCD_TO_BIN(hour); - BCD_TO_BIN(day); - BCD_TO_BIN(mon); - BCD_TO_BIN(year); + sec = bcd2bin(sec); + min = bcd2bin(min); + hour = bcd2bin(hour); + day = bcd2bin(day); + mon = bcd2bin(mon); + year = bcd2bin(year); if (year <= 69) year += 100; diff --git a/arch/powerpc/platforms/maple/time.c b/arch/powerpc/platforms/maple/time.c index 53bca132fb4..eac569dee27 100644 --- a/arch/powerpc/platforms/maple/time.c +++ b/arch/powerpc/platforms/maple/time.c @@ -68,12 +68,12 @@ void maple_get_rtc_time(struct rtc_time *tm) if (!(maple_clock_read(RTC_CONTROL) & RTC_DM_BINARY) || RTC_ALWAYS_BCD) { - BCD_TO_BIN(tm->tm_sec); - BCD_TO_BIN(tm->tm_min); - BCD_TO_BIN(tm->tm_hour); - BCD_TO_BIN(tm->tm_mday); - BCD_TO_BIN(tm->tm_mon); - BCD_TO_BIN(tm->tm_year); + tm->tm_sec = bcd2bin(tm->tm_sec); + tm->tm_min = bcd2bin(tm->tm_min); + tm->tm_hour = bcd2bin(tm->tm_hour); + tm->tm_mday = bcd2bin(tm->tm_mday); + tm->tm_mon = bcd2bin(tm->tm_mon); + tm->tm_year = bcd2bin(tm->tm_year); } if ((tm->tm_year + 1900) < 1970) tm->tm_year += 100; @@ -104,12 +104,12 @@ int maple_set_rtc_time(struct rtc_time *tm) year = tm->tm_year; if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD) { - BIN_TO_BCD(sec); - BIN_TO_BCD(min); - BIN_TO_BCD(hour); - BIN_TO_BCD(mon); - BIN_TO_BCD(mday); - BIN_TO_BCD(year); + sec = bin2bcd(sec); + min = bin2bcd(min); + hour = bin2bcd(hour); + mon = bin2bcd(mon); + mday = bin2bcd(mday); + year = bin2bcd(year); } maple_clock_write(sec, RTC_SECONDS); maple_clock_write(min, RTC_MINUTES); -- cgit v1.2.3 From f3d3d307e6f577de3b384ef64ffb03c8b5676748 Mon Sep 17 00:00:00 2001 From: Nathan Lynch Date: Wed, 13 Aug 2008 07:34:57 +1000 Subject: powerpc: Remove redundant sysfs_remove_file calls for cache info When removing a directory, the sysfs core takes care of removing files in the directory (see sysfs_remove_dir()). So when we are about to delete a kobject (and thus cause its sysfs directory to be removed), we don't have to explicitly remove the files attached to it, although it's harmless to do so. Signed-off-by: Nathan Lynch Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/sysfs.c | 11 ++--------- 1 file changed, 2 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/sysfs.c b/arch/powerpc/kernel/sysfs.c index 56d172d16e5..12058db7009 100644 --- a/arch/powerpc/kernel/sysfs.c +++ b/arch/powerpc/kernel/sysfs.c @@ -641,16 +641,9 @@ static void remove_cache_info(struct sys_device *sysdev) int cpu = sysdev->id; cache_desc = per_cpu(cache_desc, cpu); - if (cache_desc != NULL) { - sysfs_remove_file(&cache_desc->kobj, &cache_size_attr.attr); - sysfs_remove_file(&cache_desc->kobj, &cache_line_size_attr.attr); - sysfs_remove_file(&cache_desc->kobj, &cache_type_attr.attr); - sysfs_remove_file(&cache_desc->kobj, &cache_level_attr.attr); - sysfs_remove_file(&cache_desc->kobj, &cache_nr_sets_attr.attr); - sysfs_remove_file(&cache_desc->kobj, &cache_assoc_attr.attr); - + if (cache_desc != NULL) kobject_put(&cache_desc->kobj); - } + cache_toplevel = per_cpu(cache_toplevel, cpu); if (cache_toplevel != NULL) kobject_put(cache_toplevel); -- cgit v1.2.3 From 41eba0ad0033967eda346dd833194e96fdf5f405 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Mon, 18 Aug 2008 14:23:48 +1000 Subject: powerpc: Turn get/set_hard_smp_proccessor_id into inlines They don't need to be macros, and having them as inline functions avoids warnings about unused variables on some configurations when the argument isn't evaluated. Signed-off-by: Benjamin Herrenschmidt Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/smp.h | 39 +++++++++++++++++++++++++++++---------- 1 file changed, 29 insertions(+), 10 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/smp.h b/arch/powerpc/include/asm/smp.h index 4d28e1e4521..c092f84302f 100644 --- a/arch/powerpc/include/asm/smp.h +++ b/arch/powerpc/include/asm/smp.h @@ -56,9 +56,16 @@ extern int smp_hw_index[]; #define raw_smp_processor_id() (current_thread_info()->cpu) #define hard_smp_processor_id() (smp_hw_index[smp_processor_id()]) -#define get_hard_smp_processor_id(cpu) (smp_hw_index[(cpu)]) -#define set_hard_smp_processor_id(cpu, phys)\ - (smp_hw_index[(cpu)] = (phys)) + +static inline int get_hard_smp_processor_id(int cpu) +{ + return smp_hw_index[cpu]; +} + +static inline void set_hard_smp_processor_id(int cpu, int phys) +{ + smp_hw_index[cpu] = phys; +} #endif DECLARE_PER_CPU(cpumask_t, cpu_sibling_map); @@ -92,9 +99,15 @@ extern void __cpu_die(unsigned int cpu); #endif /* CONFIG_SMP */ #ifdef CONFIG_PPC64 -#define get_hard_smp_processor_id(CPU) (paca[(CPU)].hw_cpu_id) -#define set_hard_smp_processor_id(CPU, VAL) \ - do { (paca[(CPU)].hw_cpu_id = (VAL)); } while (0) +static inline int get_hard_smp_processor_id(int cpu) +{ + return paca[cpu].hw_cpu_id; +} + +static inline void set_hard_smp_processor_id(int cpu, int phys) +{ + paca[cpu].hw_cpu_id = phys; +} extern void smp_release_cpus(void); @@ -102,10 +115,16 @@ extern void smp_release_cpus(void); /* 32-bit */ #ifndef CONFIG_SMP extern int boot_cpuid_phys; -#define get_hard_smp_processor_id(cpu) boot_cpuid_phys -#define set_hard_smp_processor_id(cpu, phys) -#endif -#endif +static inline int get_hard_smp_processor_id(int cpu) +{ + return boot_cpuid_phys; +} + +static inline void set_hard_smp_processor_id(int cpu, int phys) +{ +} +#endif /* !CONFIG_SMP */ +#endif /* !CONFIG_PPC64 */ extern int smt_enabled_at_boot; -- cgit v1.2.3 From b950bdd0fc247d0ab4aea88d46e8cced3eac949e Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Mon, 18 Aug 2008 14:23:51 +1000 Subject: powerpc: Expose PMCs & cache topology in sysfs on 32-bit The file arch/powerpc/kernel/sysfs.c is currently only compiled for 64-bit kernels. It contain code to register CPU sysdevs in sysfs and add various properties such as cache topology and raw access by root to performance monitor counters (PMCs). A lot of that can be re-used as is on 32-bits. This makes the file be built for both, with appropriate ifdef'ing for the few bits that are really 64-bit specific, and adds some support for the raw PMCs for 75x and 74xx processors. Signed-off-by: Benjamin Herrenschmidt Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/cputable.h | 1 + arch/powerpc/kernel/Makefile | 4 +- arch/powerpc/kernel/cputable.c | 24 ++++++++ arch/powerpc/kernel/setup_32.c | 11 ---- arch/powerpc/kernel/sysfs.c | 106 ++++++++++++++++++++++++++------ arch/powerpc/oprofile/op_model_power4.c | 4 +- 6 files changed, 117 insertions(+), 33 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/cputable.h b/arch/powerpc/include/asm/cputable.h index ef8a248dfd5..f99813f1ede 100644 --- a/arch/powerpc/include/asm/cputable.h +++ b/arch/powerpc/include/asm/cputable.h @@ -62,6 +62,7 @@ enum powerpc_pmc_type { PPC_PMC_DEFAULT = 0, PPC_PMC_IBM = 1, PPC_PMC_PA6T = 2, + PPC_PMC_G4 = 3, }; struct pt_regs; diff --git a/arch/powerpc/kernel/Makefile b/arch/powerpc/kernel/Makefile index 64f5948ebc9..f17b5792ebc 100644 --- a/arch/powerpc/kernel/Makefile +++ b/arch/powerpc/kernel/Makefile @@ -27,13 +27,13 @@ endif obj-y := cputable.o ptrace.o syscalls.o \ irq.o align.o signal_32.o pmc.o vdso.o \ init_task.o process.o systbl.o idle.o \ - signal.o + signal.o sysfs.o obj-y += vdso32/ obj-$(CONFIG_PPC64) += setup_64.o sys_ppc32.o \ signal_64.o ptrace32.o \ paca.o cpu_setup_ppc970.o \ cpu_setup_pa6t.o \ - firmware.o sysfs.o nvram_64.o + firmware.o nvram_64.o obj-$(CONFIG_PPC64) += vdso64/ obj-$(CONFIG_ALTIVEC) += vecemu.o vector.o obj-$(CONFIG_PPC_970_NAP) += idle_power4.o diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c index 25c273c761d..e70d0483fb4 100644 --- a/arch/powerpc/kernel/cputable.c +++ b/arch/powerpc/kernel/cputable.c @@ -610,6 +610,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_IBM, .cpu_setup = __setup_cpu_750cx, .machine_check = machine_check_generic, .platform = "ppc750", @@ -623,6 +624,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_IBM, .cpu_setup = __setup_cpu_750cx, .machine_check = machine_check_generic, .platform = "ppc750", @@ -636,6 +638,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_IBM, .cpu_setup = __setup_cpu_750cx, .machine_check = machine_check_generic, .platform = "ppc750", @@ -649,6 +652,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_IBM, .cpu_setup = __setup_cpu_750, .machine_check = machine_check_generic, .platform = "ppc750", @@ -662,6 +666,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_IBM, .cpu_setup = __setup_cpu_750, .machine_check = machine_check_generic, .platform = "ppc750", @@ -675,6 +680,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_IBM, .cpu_setup = __setup_cpu_750, .machine_check = machine_check_generic, .platform = "ppc750", @@ -688,6 +694,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_IBM, .cpu_setup = __setup_cpu_750, .machine_check = machine_check_generic, .platform = "ppc750", @@ -701,6 +708,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_IBM, .cpu_setup = __setup_cpu_750fx, .machine_check = machine_check_generic, .platform = "ppc750", @@ -714,6 +722,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_IBM, .cpu_setup = __setup_cpu_750fx, .machine_check = machine_check_generic, .platform = "ppc750", @@ -727,6 +736,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_IBM, .cpu_setup = __setup_cpu_750, .machine_check = machine_check_generic, .platform = "ppc750", @@ -741,6 +751,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_7400, .machine_check = machine_check_generic, .platform = "ppc7400", @@ -755,6 +766,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_7400, .machine_check = machine_check_generic, .platform = "ppc7400", @@ -769,6 +781,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 4, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_7410, .machine_check = machine_check_generic, .platform = "ppc7400", @@ -783,6 +796,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, @@ -799,6 +813,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, @@ -815,6 +830,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, @@ -831,6 +847,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, @@ -847,6 +864,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, @@ -863,6 +881,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, @@ -879,6 +898,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, @@ -895,6 +915,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, @@ -910,6 +931,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, @@ -926,6 +948,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, @@ -942,6 +965,7 @@ static struct cpu_spec __initdata cpu_specs[] = { .icache_bsize = 32, .dcache_bsize = 32, .num_pmcs = 6, + .pmc_type = PPC_PMC_G4, .cpu_setup = __setup_cpu_745x, .oprofile_cpu_type = "ppc/7450", .oprofile_type = PPC_OPROFILE_G4, diff --git a/arch/powerpc/kernel/setup_32.c b/arch/powerpc/kernel/setup_32.c index 066e65c59b5..1e0df1658d3 100644 --- a/arch/powerpc/kernel/setup_32.c +++ b/arch/powerpc/kernel/setup_32.c @@ -209,23 +209,12 @@ EXPORT_SYMBOL(nvram_sync); #endif /* CONFIG_NVRAM */ -static DEFINE_PER_CPU(struct cpu, cpu_devices); - int __init ppc_init(void) { - int cpu; - /* clear the progress line */ if (ppc_md.progress) ppc_md.progress(" ", 0xffff); - /* register CPU devices */ - for_each_possible_cpu(cpu) { - struct cpu *c = &per_cpu(cpu_devices, cpu); - c->hotpluggable = 1; - register_cpu(c, cpu); - } - /* call platform init */ if (ppc_md.init != NULL) { ppc_md.init(); diff --git a/arch/powerpc/kernel/sysfs.c b/arch/powerpc/kernel/sysfs.c index 12058db7009..ef2ad92a417 100644 --- a/arch/powerpc/kernel/sysfs.c +++ b/arch/powerpc/kernel/sysfs.c @@ -15,18 +15,24 @@ #include #include #include -#include -#include #include #include +#ifdef CONFIG_PPC64 +#include +#include +#endif + static DEFINE_PER_CPU(struct cpu, cpu_devices); static DEFINE_PER_CPU(struct kobject *, cache_toplevel); -/* SMT stuff */ +/* + * SMT snooze delay stuff, 64-bit only for now + */ + +#ifdef CONFIG_PPC64 -#ifdef CONFIG_PPC_MULTIPLATFORM /* Time in microseconds we delay before sleeping in the idle loop */ DEFINE_PER_CPU(unsigned long, smt_snooze_delay) = { 100 }; @@ -106,7 +112,7 @@ static int __init setup_smt_snooze_delay(char *str) } __setup("smt-snooze-delay=", setup_smt_snooze_delay); -#endif /* CONFIG_PPC_MULTIPLATFORM */ +#endif /* CONFIG_PPC64 */ /* * Enabling PMCs will slow partition context switch times so we only do @@ -115,7 +121,7 @@ __setup("smt-snooze-delay=", setup_smt_snooze_delay); static DEFINE_PER_CPU(char, pmcs_enabled); -void ppc64_enable_pmcs(void) +void ppc_enable_pmcs(void) { /* Only need to enable them once */ if (__get_cpu_var(pmcs_enabled)) @@ -126,7 +132,7 @@ void ppc64_enable_pmcs(void) if (ppc_md.enable_pmcs) ppc_md.enable_pmcs(); } -EXPORT_SYMBOL(ppc64_enable_pmcs); +EXPORT_SYMBOL(ppc_enable_pmcs); /* XXX convert to rusty's on_one_cpu */ static unsigned long run_on_cpu(unsigned long cpu, @@ -154,7 +160,7 @@ static unsigned long read_##NAME(unsigned long junk) \ } \ static unsigned long write_##NAME(unsigned long val) \ { \ - ppc64_enable_pmcs(); \ + ppc_enable_pmcs(); \ mtspr(ADDRESS, val); \ return 0; \ } \ @@ -184,28 +190,53 @@ static ssize_t __used \ * that are implemented on the current processor */ +#ifdef CONFIG_PPC64 +#define HAS_PPC_PMC_CLASSIC 1 +#define HAS_PPC_PMC_IBM 1 +#define HAS_PPC_PMC_PA6T 1 +#elif CONFIG_6xx +#define HAS_PPC_PMC_CLASSIC 1 +#define HAS_PPC_PMC_IBM 1 +#define HAS_PPC_PMC_G4 1 +#endif + + +#ifdef HAS_PPC_PMC_CLASSIC SYSFS_PMCSETUP(mmcr0, SPRN_MMCR0); SYSFS_PMCSETUP(mmcr1, SPRN_MMCR1); -SYSFS_PMCSETUP(mmcra, SPRN_MMCRA); SYSFS_PMCSETUP(pmc1, SPRN_PMC1); SYSFS_PMCSETUP(pmc2, SPRN_PMC2); SYSFS_PMCSETUP(pmc3, SPRN_PMC3); SYSFS_PMCSETUP(pmc4, SPRN_PMC4); SYSFS_PMCSETUP(pmc5, SPRN_PMC5); SYSFS_PMCSETUP(pmc6, SPRN_PMC6); + +#ifdef HAS_PPC_PMC_G4 +SYSFS_PMCSETUP(mmcr2, SPRN_MMCR2); +#endif + +#ifdef CONFIG_PPC64 SYSFS_PMCSETUP(pmc7, SPRN_PMC7); SYSFS_PMCSETUP(pmc8, SPRN_PMC8); + +SYSFS_PMCSETUP(mmcra, SPRN_MMCRA); SYSFS_PMCSETUP(purr, SPRN_PURR); SYSFS_PMCSETUP(spurr, SPRN_SPURR); SYSFS_PMCSETUP(dscr, SPRN_DSCR); +static SYSDEV_ATTR(mmcra, 0600, show_mmcra, store_mmcra); +static SYSDEV_ATTR(spurr, 0600, show_spurr, NULL); +static SYSDEV_ATTR(dscr, 0600, show_dscr, store_dscr); +static SYSDEV_ATTR(purr, 0600, show_purr, store_purr); +#endif /* CONFIG_PPC64 */ + +#ifdef HAS_PPC_PMC_PA6T SYSFS_PMCSETUP(pa6t_pmc0, SPRN_PA6T_PMC0); SYSFS_PMCSETUP(pa6t_pmc1, SPRN_PA6T_PMC1); SYSFS_PMCSETUP(pa6t_pmc2, SPRN_PA6T_PMC2); SYSFS_PMCSETUP(pa6t_pmc3, SPRN_PA6T_PMC3); SYSFS_PMCSETUP(pa6t_pmc4, SPRN_PA6T_PMC4); SYSFS_PMCSETUP(pa6t_pmc5, SPRN_PA6T_PMC5); - #ifdef CONFIG_DEBUG_KERNEL SYSFS_PMCSETUP(hid0, SPRN_HID0); SYSFS_PMCSETUP(hid1, SPRN_HID1); @@ -236,28 +267,37 @@ SYSFS_PMCSETUP(tsr1, SPRN_PA6T_TSR1); SYSFS_PMCSETUP(tsr2, SPRN_PA6T_TSR2); SYSFS_PMCSETUP(tsr3, SPRN_PA6T_TSR3); #endif /* CONFIG_DEBUG_KERNEL */ +#endif /* HAS_PPC_PMC_PA6T */ -static SYSDEV_ATTR(mmcra, 0600, show_mmcra, store_mmcra); -static SYSDEV_ATTR(spurr, 0600, show_spurr, NULL); -static SYSDEV_ATTR(dscr, 0600, show_dscr, store_dscr); -static SYSDEV_ATTR(purr, 0600, show_purr, store_purr); - +#ifdef HAS_PPC_PMC_IBM static struct sysdev_attribute ibm_common_attrs[] = { _SYSDEV_ATTR(mmcr0, 0600, show_mmcr0, store_mmcr0), _SYSDEV_ATTR(mmcr1, 0600, show_mmcr1, store_mmcr1), }; +#endif /* HAS_PPC_PMC_G4 */ + +#ifdef HAS_PPC_PMC_G4 +static struct sysdev_attribute g4_common_attrs[] = { + _SYSDEV_ATTR(mmcr0, 0600, show_mmcr0, store_mmcr0), + _SYSDEV_ATTR(mmcr1, 0600, show_mmcr1, store_mmcr1), + _SYSDEV_ATTR(mmcr2, 0600, show_mmcr2, store_mmcr2), +}; +#endif /* HAS_PPC_PMC_G4 */ -static struct sysdev_attribute ibm_pmc_attrs[] = { +static struct sysdev_attribute classic_pmc_attrs[] = { _SYSDEV_ATTR(pmc1, 0600, show_pmc1, store_pmc1), _SYSDEV_ATTR(pmc2, 0600, show_pmc2, store_pmc2), _SYSDEV_ATTR(pmc3, 0600, show_pmc3, store_pmc3), _SYSDEV_ATTR(pmc4, 0600, show_pmc4, store_pmc4), _SYSDEV_ATTR(pmc5, 0600, show_pmc5, store_pmc5), _SYSDEV_ATTR(pmc6, 0600, show_pmc6, store_pmc6), +#ifdef CONFIG_PPC64 _SYSDEV_ATTR(pmc7, 0600, show_pmc7, store_pmc7), _SYSDEV_ATTR(pmc8, 0600, show_pmc8, store_pmc8), +#endif }; +#ifdef HAS_PPC_PMC_PA6T static struct sysdev_attribute pa6t_attrs[] = { _SYSDEV_ATTR(mmcr0, 0600, show_mmcr0, store_mmcr0), _SYSDEV_ATTR(mmcr1, 0600, show_mmcr1, store_mmcr1), @@ -298,6 +338,8 @@ static struct sysdev_attribute pa6t_attrs[] = { _SYSDEV_ATTR(tsr3, 0600, show_tsr3, store_tsr3), #endif /* CONFIG_DEBUG_KERNEL */ }; +#endif /* HAS_PPC_PMC_PA6T */ +#endif /* HAS_PPC_PMC_CLASSIC */ struct cache_desc { struct kobject kobj; @@ -588,23 +630,36 @@ static void __cpuinit register_cpu_online(unsigned int cpu) struct sysdev_attribute *attrs, *pmc_attrs; int i, nattrs; +#ifdef CONFIG_PPC64 if (!firmware_has_feature(FW_FEATURE_ISERIES) && cpu_has_feature(CPU_FTR_SMT)) sysdev_create_file(s, &attr_smt_snooze_delay); +#endif /* PMC stuff */ switch (cur_cpu_spec->pmc_type) { +#ifdef HAS_PPC_PMC_IBM case PPC_PMC_IBM: attrs = ibm_common_attrs; nattrs = sizeof(ibm_common_attrs) / sizeof(struct sysdev_attribute); - pmc_attrs = ibm_pmc_attrs; + pmc_attrs = classic_pmc_attrs; break; +#endif /* HAS_PPC_PMC_IBM */ +#ifdef HAS_PPC_PMC_G4 + case PPC_PMC_G4: + attrs = g4_common_attrs; + nattrs = sizeof(g4_common_attrs) / sizeof(struct sysdev_attribute); + pmc_attrs = classic_pmc_attrs; + break; +#endif /* HAS_PPC_PMC_G4 */ +#ifdef HAS_PPC_PMC_PA6T case PPC_PMC_PA6T: /* PA Semi starts counting at PMC0 */ attrs = pa6t_attrs; nattrs = sizeof(pa6t_attrs) / sizeof(struct sysdev_attribute); pmc_attrs = NULL; break; +#endif /* HAS_PPC_PMC_PA6T */ default: attrs = NULL; nattrs = 0; @@ -618,6 +673,7 @@ static void __cpuinit register_cpu_online(unsigned int cpu) for (i = 0; i < cur_cpu_spec->num_pmcs; i++) sysdev_create_file(s, &pmc_attrs[i]); +#ifdef CONFIG_PPC64 if (cpu_has_feature(CPU_FTR_MMCRA)) sysdev_create_file(s, &attr_mmcra); @@ -629,6 +685,7 @@ static void __cpuinit register_cpu_online(unsigned int cpu) if (cpu_has_feature(CPU_FTR_DSCR)) sysdev_create_file(s, &attr_dscr); +#endif /* CONFIG_PPC64 */ create_cache_info(s); } @@ -664,17 +721,28 @@ static void unregister_cpu_online(unsigned int cpu) /* PMC stuff */ switch (cur_cpu_spec->pmc_type) { +#ifdef HAS_PPC_PMC_IBM case PPC_PMC_IBM: attrs = ibm_common_attrs; nattrs = sizeof(ibm_common_attrs) / sizeof(struct sysdev_attribute); - pmc_attrs = ibm_pmc_attrs; + pmc_attrs = classic_pmc_attrs; + break; +#endif /* HAS_PPC_PMC_IBM */ +#ifdef HAS_PPC_PMC_G4 + case PPC_PMC_G4: + attrs = g4_common_attrs; + nattrs = sizeof(g4_common_attrs) / sizeof(struct sysdev_attribute); + pmc_attrs = classic_pmc_attrs; break; +#endif /* HAS_PPC_PMC_G4 */ +#ifdef HAS_PPC_PMC_PA6T case PPC_PMC_PA6T: /* PA Semi starts counting at PMC0 */ attrs = pa6t_attrs; nattrs = sizeof(pa6t_attrs) / sizeof(struct sysdev_attribute); pmc_attrs = NULL; break; +#endif /* HAS_PPC_PMC_PA6T */ default: attrs = NULL; nattrs = 0; @@ -688,6 +756,7 @@ static void unregister_cpu_online(unsigned int cpu) for (i = 0; i < cur_cpu_spec->num_pmcs; i++) sysdev_remove_file(s, &pmc_attrs[i]); +#ifdef CONFIG_PPC64 if (cpu_has_feature(CPU_FTR_MMCRA)) sysdev_remove_file(s, &attr_mmcra); @@ -699,6 +768,7 @@ static void unregister_cpu_online(unsigned int cpu) if (cpu_has_feature(CPU_FTR_DSCR)) sysdev_remove_file(s, &attr_dscr); +#endif /* CONFIG_PPC64 */ remove_cache_info(s); } diff --git a/arch/powerpc/oprofile/op_model_power4.c b/arch/powerpc/oprofile/op_model_power4.c index 446a8bbb847..3e3d91f536e 100644 --- a/arch/powerpc/oprofile/op_model_power4.c +++ b/arch/powerpc/oprofile/op_model_power4.c @@ -64,7 +64,7 @@ static int power4_reg_setup(struct op_counter_config *ctr, return 0; } -extern void ppc64_enable_pmcs(void); +extern void ppc_enable_pmcs(void); /* * Older CPUs require the MMCRA sample bit to be always set, but newer @@ -91,7 +91,7 @@ static int power4_cpu_setup(struct op_counter_config *ctr) unsigned int mmcr0 = mmcr0_val; unsigned long mmcra = mmcra_val; - ppc64_enable_pmcs(); + ppc_enable_pmcs(); /* set the freeze bit */ mmcr0 |= MMCR0_FC; -- cgit v1.2.3 From 7713fef06517d216f96ee7c8ad750e72bc08d38f Mon Sep 17 00:00:00 2001 From: Stephen Rothwell Date: Tue, 19 Aug 2008 18:19:25 +1000 Subject: powerpc: Remove include of linux/of_device.h from asm/of_device.h Now that we have removed all inclusions of asm/of_device.h, this compatability include can be removed. Signed-off-by: Stephen Rothwell Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/of_device.h | 3 --- 1 file changed, 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/of_device.h b/arch/powerpc/include/asm/of_device.h index 3c123990ca2..a64debf177d 100644 --- a/arch/powerpc/include/asm/of_device.h +++ b/arch/powerpc/include/asm/of_device.h @@ -24,8 +24,5 @@ extern struct of_device *of_device_alloc(struct device_node *np, extern int of_device_uevent(struct device *dev, struct kobj_uevent_env *env); -/* This is just here during the transition */ -#include - #endif /* __KERNEL__ */ #endif /* _ASM_POWERPC_OF_DEVICE_H */ -- cgit v1.2.3 From e30c98758453d743fab00e45da0eac6fc581958a Mon Sep 17 00:00:00 2001 From: Tirumala R Marri Date: Thu, 21 Aug 2008 18:53:34 +0000 Subject: powerpc/44x: AMCC PPC460GT/EX PCI-E de-emphasis adjustment fix During recent tests with PCI-E , it has been found the DRV + De-Emphasis values are not optimum. These new values are tested thouroughly. Signed-off-by: Tirumala R Marri Signed-off-by: Feng Kan fkan@amcc.com Acked-by: Stefan Roese Signed-off-by: Josh Boyer --- arch/powerpc/sysdev/ppc4xx_pci.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/ppc4xx_pci.c b/arch/powerpc/sysdev/ppc4xx_pci.c index fb368dfde5d..d5c345dbb89 100644 --- a/arch/powerpc/sysdev/ppc4xx_pci.c +++ b/arch/powerpc/sysdev/ppc4xx_pci.c @@ -810,7 +810,7 @@ static int ppc460ex_pciex_init_port_hw(struct ppc4xx_pciex_port *port) switch (port->index) { case 0: mtdcri(SDR0, PESDR0_460EX_L0CDRCTL, 0x00003230); - mtdcri(SDR0, PESDR0_460EX_L0DRV, 0x00000136); + mtdcri(SDR0, PESDR0_460EX_L0DRV, 0x00000130); mtdcri(SDR0, PESDR0_460EX_L0CLK, 0x00000006); mtdcri(SDR0, PESDR0_460EX_PHY_CTL_RST,0x10000000); @@ -821,10 +821,10 @@ static int ppc460ex_pciex_init_port_hw(struct ppc4xx_pciex_port *port) mtdcri(SDR0, PESDR1_460EX_L1CDRCTL, 0x00003230); mtdcri(SDR0, PESDR1_460EX_L2CDRCTL, 0x00003230); mtdcri(SDR0, PESDR1_460EX_L3CDRCTL, 0x00003230); - mtdcri(SDR0, PESDR1_460EX_L0DRV, 0x00000136); - mtdcri(SDR0, PESDR1_460EX_L1DRV, 0x00000136); - mtdcri(SDR0, PESDR1_460EX_L2DRV, 0x00000136); - mtdcri(SDR0, PESDR1_460EX_L3DRV, 0x00000136); + mtdcri(SDR0, PESDR1_460EX_L0DRV, 0x00000130); + mtdcri(SDR0, PESDR1_460EX_L1DRV, 0x00000130); + mtdcri(SDR0, PESDR1_460EX_L2DRV, 0x00000130); + mtdcri(SDR0, PESDR1_460EX_L3DRV, 0x00000130); mtdcri(SDR0, PESDR1_460EX_L0CLK, 0x00000006); mtdcri(SDR0, PESDR1_460EX_L1CLK, 0x00000006); mtdcri(SDR0, PESDR1_460EX_L2CLK, 0x00000006); -- cgit v1.2.3 From 775d5a110b8a0bc9a0ccf3b831a8991b6c1d84dd Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Tue, 19 Aug 2008 11:25:15 -0400 Subject: powerpc/44x: Add PowerPC 44x simple platform support This adds a common board file for almost all of the "simple" PowerPC 44x boards that exist today. This is intended to be a single place to add support for boards that do not differ in platform support from most of the evaluation boards that are used as reference platforms. Boards that have specific requirements or custom hardware setup should still have their own board.c file. Signed-off-by: Josh Boyer --- arch/powerpc/platforms/44x/Kconfig | 7 +++ arch/powerpc/platforms/44x/Makefile | 1 + arch/powerpc/platforms/44x/ppc44x_simple.c | 85 ++++++++++++++++++++++++++++++ 3 files changed, 93 insertions(+) create mode 100644 arch/powerpc/platforms/44x/ppc44x_simple.c (limited to 'arch') diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig index 249ba01c667..97c634c8f9d 100644 --- a/arch/powerpc/platforms/44x/Kconfig +++ b/arch/powerpc/platforms/44x/Kconfig @@ -127,6 +127,13 @@ config XILINX_VIRTEX440_GENERIC_BOARD Most Virtex 5 designs should use this unless it needs to do some special configuration at board probe time. +config PPC44x_SIMPLE + bool "Simple PowerPC 44x board support" + depends on 44x + default n + help + This option enables the simple PowerPC 44x platform support. + # 44x specific CPU modules, selected based on the board above. config 440EP bool diff --git a/arch/powerpc/platforms/44x/Makefile b/arch/powerpc/platforms/44x/Makefile index 8d0b1a192d6..73c1df5bc05 100644 --- a/arch/powerpc/platforms/44x/Makefile +++ b/arch/powerpc/platforms/44x/Makefile @@ -1,4 +1,5 @@ obj-$(CONFIG_44x) := misc_44x.o idle.o +obj-$(CONFIG_PPC44x_SIMPLE) += ppc44x_simple.o obj-$(CONFIG_EBONY) += ebony.o obj-$(CONFIG_TAISHAN) += taishan.o obj-$(CONFIG_BAMBOO) += bamboo.o diff --git a/arch/powerpc/platforms/44x/ppc44x_simple.c b/arch/powerpc/platforms/44x/ppc44x_simple.c new file mode 100644 index 00000000000..32b0535f29f --- /dev/null +++ b/arch/powerpc/platforms/44x/ppc44x_simple.c @@ -0,0 +1,85 @@ +/* + * Generic PowerPC 44x platform support + * + * Copyright 2008 IBM Corporation + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; version 2 of the License. + * + * This implements simple platform support for PowerPC 44x chips. This is + * mostly used for eval boards or other simple and "generic" 44x boards. If + * your board has custom functions or hardware, then you will likely want to + * implement your own board.c file to accommodate it. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +static __initdata struct of_device_id ppc44x_of_bus[] = { + { .compatible = "ibm,plb4", }, + { .compatible = "ibm,opb", }, + { .compatible = "ibm,ebc", }, + { .compatible = "simple-bus", }, + {}, +}; + +static int __init ppc44x_device_probe(void) +{ + of_platform_bus_probe(NULL, ppc44x_of_bus, NULL); + + return 0; +} +machine_device_initcall(ppc44x_simple, ppc44x_device_probe); + +/* This is the list of boards that can be supported by this simple + * platform code. This does _not_ mean the boards are compatible, + * as they most certainly are not from a device tree perspective. + * However, their differences are handled by the device tree and the + * drivers and therefore they don't need custom board support files. + * + * Again, if your board needs to do things differently then create a + * board.c file for it rather than adding it to this list. + */ +static char *board[] __initdata = { + "amcc,bamboo", + "amcc,cayonlands", + "ibm,ebony", + "amcc,katmai", + "amcc,rainier", + "amcc,sequoia", + "amcc,taishan" +}; + +static int __init ppc44x_probe(void) +{ + unsigned long root = of_get_flat_dt_root(); + int i = 0; + + for (i = 0; i < ARRAY_SIZE(board); i++) { + if (of_flat_dt_is_compatible(root, board[i])) { + ppc_pci_flags = PPC_PCI_REASSIGN_ALL_RSRC; + return 1; + } + } + + return 0; +} + +define_machine(ppc44x_simple) { + .name = "PowerPC 44x Platform", + .probe = ppc44x_probe, + .progress = udbg_progress, + .init_IRQ = uic_init_tree, + .get_irq = uic_get_irq, + .restart = ppc4xx_reset_system, + .calibrate_decr = generic_calibrate_decr, +}; -- cgit v1.2.3 From 380c313ab301e9d35ead5cd9ead737682eba304b Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Tue, 19 Aug 2008 11:26:24 -0400 Subject: powerpc/44x: Migrate Bamboo support to ppc44x_simple Migrate the AMCC Bamboo board to use the ppc44x_simple platform file. Signed-off-by: Josh Boyer --- arch/powerpc/platforms/44x/Kconfig | 2 ++ arch/powerpc/platforms/44x/Makefile | 2 -- arch/powerpc/platforms/44x/bamboo.c | 62 ------------------------------------- 3 files changed, 2 insertions(+), 64 deletions(-) delete mode 100644 arch/powerpc/platforms/44x/bamboo.c (limited to 'arch') diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig index 97c634c8f9d..0958285e110 100644 --- a/arch/powerpc/platforms/44x/Kconfig +++ b/arch/powerpc/platforms/44x/Kconfig @@ -2,6 +2,7 @@ config BAMBOO bool "Bamboo" depends on 44x default n + select PPC44x_SIMPLE select 440EP select PCI help @@ -90,6 +91,7 @@ config YOSEMITE bool "Yosemite" depends on 44x default n + select PPC44x_SIMPLE select 440EP select PCI help diff --git a/arch/powerpc/platforms/44x/Makefile b/arch/powerpc/platforms/44x/Makefile index 73c1df5bc05..ca18a326f67 100644 --- a/arch/powerpc/platforms/44x/Makefile +++ b/arch/powerpc/platforms/44x/Makefile @@ -2,8 +2,6 @@ obj-$(CONFIG_44x) := misc_44x.o idle.o obj-$(CONFIG_PPC44x_SIMPLE) += ppc44x_simple.o obj-$(CONFIG_EBONY) += ebony.o obj-$(CONFIG_TAISHAN) += taishan.o -obj-$(CONFIG_BAMBOO) += bamboo.o -obj-$(CONFIG_YOSEMITE) += bamboo.o obj-$(CONFIG_SAM440EP) += sam440ep.o obj-$(CONFIG_SEQUOIA) += sequoia.o obj-$(CONFIG_KATMAI) += katmai.o diff --git a/arch/powerpc/platforms/44x/bamboo.c b/arch/powerpc/platforms/44x/bamboo.c deleted file mode 100644 index cef169e9515..00000000000 --- a/arch/powerpc/platforms/44x/bamboo.c +++ /dev/null @@ -1,62 +0,0 @@ -/* - * Bamboo board specific routines - * - * Wade Farnsworth - * Copyright 2004 MontaVista Software Inc. - * - * Rewritten and ported to the merged powerpc tree: - * Josh Boyer - * Copyright 2007 IBM Corporation - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include -#include - -#include -#include -#include -#include -#include -#include -#include - -static __initdata struct of_device_id bamboo_of_bus[] = { - { .compatible = "ibm,plb4", }, - { .compatible = "ibm,opb", }, - { .compatible = "ibm,ebc", }, - {}, -}; - -static int __init bamboo_device_probe(void) -{ - of_platform_bus_probe(NULL, bamboo_of_bus, NULL); - - return 0; -} -machine_device_initcall(bamboo, bamboo_device_probe); - -static int __init bamboo_probe(void) -{ - unsigned long root = of_get_flat_dt_root(); - - if (!of_flat_dt_is_compatible(root, "amcc,bamboo")) - return 0; - - ppc_pci_flags = PPC_PCI_REASSIGN_ALL_RSRC; - - return 1; -} - -define_machine(bamboo) { - .name = "Bamboo", - .probe = bamboo_probe, - .progress = udbg_progress, - .init_IRQ = uic_init_tree, - .get_irq = uic_get_irq, - .restart = ppc4xx_reset_system, - .calibrate_decr = generic_calibrate_decr, -}; -- cgit v1.2.3 From aaf136c29d7b1dd505256c26a191ef1ad5f0a448 Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Tue, 19 Aug 2008 11:26:35 -0400 Subject: powerpc/44x: Migrate Canyonlands support to ppc44x_simple Migrate the AMCC Canyonlands board to use the ppc44x_simple platform file. Signed-off-by: Josh Boyer --- arch/powerpc/platforms/44x/Kconfig | 1 + arch/powerpc/platforms/44x/Makefile | 1 - arch/powerpc/platforms/44x/canyonlands.c | 63 -------------------------------- 3 files changed, 1 insertion(+), 64 deletions(-) delete mode 100644 arch/powerpc/platforms/44x/canyonlands.c (limited to 'arch') diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig index 0958285e110..92ba2d87f2f 100644 --- a/arch/powerpc/platforms/44x/Kconfig +++ b/arch/powerpc/platforms/44x/Kconfig @@ -81,6 +81,7 @@ config CANYONLANDS bool "Canyonlands" depends on 44x default n + select PPC44x_SIMPLE select 460EX select PCI select PPC4xx_PCI_EXPRESS diff --git a/arch/powerpc/platforms/44x/Makefile b/arch/powerpc/platforms/44x/Makefile index ca18a326f67..0ab626d4795 100644 --- a/arch/powerpc/platforms/44x/Makefile +++ b/arch/powerpc/platforms/44x/Makefile @@ -8,5 +8,4 @@ obj-$(CONFIG_KATMAI) += katmai.o obj-$(CONFIG_RAINIER) += rainier.o obj-$(CONFIG_WARP) += warp.o obj-$(CONFIG_WARP) += warp-nand.o -obj-$(CONFIG_CANYONLANDS) += canyonlands.o obj-$(CONFIG_XILINX_VIRTEX_5_FXT) += virtex.o diff --git a/arch/powerpc/platforms/44x/canyonlands.c b/arch/powerpc/platforms/44x/canyonlands.c deleted file mode 100644 index 3949289f51d..00000000000 --- a/arch/powerpc/platforms/44x/canyonlands.c +++ /dev/null @@ -1,63 +0,0 @@ -/* - * Canyonlands board specific routines - * - * Copyright 2008 DENX Software Engineering, Stefan Roese - * - * Based on the Katmai code by - * Benjamin Herrenschmidt - * Copyright 2007 IBM Corp. - * Josh Boyer - * Copyright 2007 IBM Corporation - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include -#include - -#include -#include -#include -#include -#include -#include -#include - -static __initdata struct of_device_id canyonlands_of_bus[] = { - { .compatible = "ibm,plb4", }, - { .compatible = "ibm,opb", }, - { .compatible = "ibm,ebc", }, - {}, -}; - -static int __init canyonlands_device_probe(void) -{ - of_platform_bus_probe(NULL, canyonlands_of_bus, NULL); - - return 0; -} -machine_device_initcall(canyonlands, canyonlands_device_probe); - -static int __init canyonlands_probe(void) -{ - unsigned long root = of_get_flat_dt_root(); - - if (!of_flat_dt_is_compatible(root, "amcc,canyonlands")) - return 0; - - ppc_pci_flags = PPC_PCI_REASSIGN_ALL_RSRC; - - return 1; -} - -define_machine(canyonlands) { - .name = "Canyonlands", - .probe = canyonlands_probe, - .progress = udbg_progress, - .init_IRQ = uic_init_tree, - .get_irq = uic_get_irq, - .restart = ppc4xx_reset_system, - .calibrate_decr = generic_calibrate_decr, -}; -- cgit v1.2.3 From cfcf81ba16ce67c2383daf0f7659983a9a0e3c46 Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Tue, 19 Aug 2008 11:26:40 -0400 Subject: powerpc/44x: Migrate Katmai support to ppc44x_simple Migrate the AMCC Katmai board to use the ppc44x_simple platform file. Signed-off-by: Josh Boyer --- arch/powerpc/platforms/44x/Kconfig | 1 + arch/powerpc/platforms/44x/Makefile | 1 - arch/powerpc/platforms/44x/katmai.c | 62 ------------------------------------- 3 files changed, 1 insertion(+), 63 deletions(-) delete mode 100644 arch/powerpc/platforms/44x/katmai.c (limited to 'arch') diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig index 92ba2d87f2f..66d44998893 100644 --- a/arch/powerpc/platforms/44x/Kconfig +++ b/arch/powerpc/platforms/44x/Kconfig @@ -49,6 +49,7 @@ config KATMAI bool "Katmai" depends on 44x default n + select PPC44x_SIMPLE select 440SPe select PCI select PPC4xx_PCI_EXPRESS diff --git a/arch/powerpc/platforms/44x/Makefile b/arch/powerpc/platforms/44x/Makefile index 0ab626d4795..2eb1cbe9bf6 100644 --- a/arch/powerpc/platforms/44x/Makefile +++ b/arch/powerpc/platforms/44x/Makefile @@ -4,7 +4,6 @@ obj-$(CONFIG_EBONY) += ebony.o obj-$(CONFIG_TAISHAN) += taishan.o obj-$(CONFIG_SAM440EP) += sam440ep.o obj-$(CONFIG_SEQUOIA) += sequoia.o -obj-$(CONFIG_KATMAI) += katmai.o obj-$(CONFIG_RAINIER) += rainier.o obj-$(CONFIG_WARP) += warp.o obj-$(CONFIG_WARP) += warp-nand.o diff --git a/arch/powerpc/platforms/44x/katmai.c b/arch/powerpc/platforms/44x/katmai.c deleted file mode 100644 index 44f4b3a00ce..00000000000 --- a/arch/powerpc/platforms/44x/katmai.c +++ /dev/null @@ -1,62 +0,0 @@ -/* - * Katmai board specific routines - * - * Benjamin Herrenschmidt - * Copyright 2007 IBM Corp. - * - * Based on the Bamboo code by - * Josh Boyer - * Copyright 2007 IBM Corporation - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include -#include - -#include -#include -#include -#include -#include -#include -#include - -static __initdata struct of_device_id katmai_of_bus[] = { - { .compatible = "ibm,plb4", }, - { .compatible = "ibm,opb", }, - { .compatible = "ibm,ebc", }, - {}, -}; - -static int __init katmai_device_probe(void) -{ - of_platform_bus_probe(NULL, katmai_of_bus, NULL); - - return 0; -} -machine_device_initcall(katmai, katmai_device_probe); - -static int __init katmai_probe(void) -{ - unsigned long root = of_get_flat_dt_root(); - - if (!of_flat_dt_is_compatible(root, "amcc,katmai")) - return 0; - - ppc_pci_flags = PPC_PCI_REASSIGN_ALL_RSRC; - - return 1; -} - -define_machine(katmai) { - .name = "Katmai", - .probe = katmai_probe, - .progress = udbg_progress, - .init_IRQ = uic_init_tree, - .get_irq = uic_get_irq, - .restart = ppc4xx_reset_system, - .calibrate_decr = generic_calibrate_decr, -}; -- cgit v1.2.3 From 5c8495d2ad3cd9d7d59dfad05bdd2a7b3c5d2e9d Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Tue, 19 Aug 2008 11:26:44 -0400 Subject: powerpc/44x: Migrate Rainier support to ppc44x_simple Migrate the AMCC Rainier board to use the ppc44x_simple platform file. Signed-off-by: Josh Boyer --- arch/powerpc/platforms/44x/Kconfig | 1 + arch/powerpc/platforms/44x/Makefile | 1 - arch/powerpc/platforms/44x/rainier.c | 62 ------------------------------------ 3 files changed, 1 insertion(+), 63 deletions(-) delete mode 100644 arch/powerpc/platforms/44x/rainier.c (limited to 'arch') diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig index 66d44998893..89e7f1f2288 100644 --- a/arch/powerpc/platforms/44x/Kconfig +++ b/arch/powerpc/platforms/44x/Kconfig @@ -60,6 +60,7 @@ config RAINIER bool "Rainier" depends on 44x default n + select PPC44x_SIMPLE select 440GRX select PCI help diff --git a/arch/powerpc/platforms/44x/Makefile b/arch/powerpc/platforms/44x/Makefile index 2eb1cbe9bf6..c201af69e83 100644 --- a/arch/powerpc/platforms/44x/Makefile +++ b/arch/powerpc/platforms/44x/Makefile @@ -4,7 +4,6 @@ obj-$(CONFIG_EBONY) += ebony.o obj-$(CONFIG_TAISHAN) += taishan.o obj-$(CONFIG_SAM440EP) += sam440ep.o obj-$(CONFIG_SEQUOIA) += sequoia.o -obj-$(CONFIG_RAINIER) += rainier.o obj-$(CONFIG_WARP) += warp.o obj-$(CONFIG_WARP) += warp-nand.o obj-$(CONFIG_XILINX_VIRTEX_5_FXT) += virtex.o diff --git a/arch/powerpc/platforms/44x/rainier.c b/arch/powerpc/platforms/44x/rainier.c deleted file mode 100644 index 4f1ff84c4b6..00000000000 --- a/arch/powerpc/platforms/44x/rainier.c +++ /dev/null @@ -1,62 +0,0 @@ -/* - * Rainier board specific routines - * - * Valentine Barshak - * Copyright 2007 MontaVista Software Inc. - * - * Based on the Bamboo code by - * Josh Boyer - * Copyright 2007 IBM Corporation - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include -#include - -#include -#include -#include -#include -#include -#include -#include - -static __initdata struct of_device_id rainier_of_bus[] = { - { .compatible = "ibm,plb4", }, - { .compatible = "ibm,opb", }, - { .compatible = "ibm,ebc", }, - {}, -}; - -static int __init rainier_device_probe(void) -{ - of_platform_bus_probe(NULL, rainier_of_bus, NULL); - - return 0; -} -machine_device_initcall(rainier, rainier_device_probe); - -static int __init rainier_probe(void) -{ - unsigned long root = of_get_flat_dt_root(); - - if (!of_flat_dt_is_compatible(root, "amcc,rainier")) - return 0; - - ppc_pci_flags = PPC_PCI_REASSIGN_ALL_RSRC; - - return 1; -} - -define_machine(rainier) { - .name = "Rainier", - .probe = rainier_probe, - .progress = udbg_progress, - .init_IRQ = uic_init_tree, - .get_irq = uic_get_irq, - .restart = ppc4xx_reset_system, - .calibrate_decr = generic_calibrate_decr, -}; -- cgit v1.2.3 From 427e817df459bdfad6be307456f61601e10b5845 Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Tue, 19 Aug 2008 11:26:48 -0400 Subject: powerpc/44x: Migrate Sequoia support to ppc44x_simple Migrate the AMCC Sequoia board to use the ppc44x_simple platform file. Signed-off-by: Josh Boyer --- arch/powerpc/platforms/44x/Kconfig | 1 + arch/powerpc/platforms/44x/Makefile | 1 - arch/powerpc/platforms/44x/sequoia.c | 63 ------------------------------------ 3 files changed, 1 insertion(+), 64 deletions(-) delete mode 100644 arch/powerpc/platforms/44x/sequoia.c (limited to 'arch') diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig index 89e7f1f2288..84e2a703666 100644 --- a/arch/powerpc/platforms/44x/Kconfig +++ b/arch/powerpc/platforms/44x/Kconfig @@ -31,6 +31,7 @@ config SEQUOIA bool "Sequoia" depends on 44x default n + select PPC44x_SIMPLE select 440EPX help This option enables support for the AMCC PPC440EPX evaluation board. diff --git a/arch/powerpc/platforms/44x/Makefile b/arch/powerpc/platforms/44x/Makefile index c201af69e83..a8a92c17098 100644 --- a/arch/powerpc/platforms/44x/Makefile +++ b/arch/powerpc/platforms/44x/Makefile @@ -3,7 +3,6 @@ obj-$(CONFIG_PPC44x_SIMPLE) += ppc44x_simple.o obj-$(CONFIG_EBONY) += ebony.o obj-$(CONFIG_TAISHAN) += taishan.o obj-$(CONFIG_SAM440EP) += sam440ep.o -obj-$(CONFIG_SEQUOIA) += sequoia.o obj-$(CONFIG_WARP) += warp.o obj-$(CONFIG_WARP) += warp-nand.o obj-$(CONFIG_XILINX_VIRTEX_5_FXT) += virtex.o diff --git a/arch/powerpc/platforms/44x/sequoia.c b/arch/powerpc/platforms/44x/sequoia.c deleted file mode 100644 index 49eb73daacd..00000000000 --- a/arch/powerpc/platforms/44x/sequoia.c +++ /dev/null @@ -1,63 +0,0 @@ -/* - * Sequoia board specific routines - * - * Valentine Barshak - * Copyright 2007 MontaVista Software Inc. - * - * Based on the Bamboo code by - * Josh Boyer - * Copyright 2007 IBM Corporation - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ -#include -#include - -#include -#include -#include -#include -#include -#include - -#include - -static __initdata struct of_device_id sequoia_of_bus[] = { - { .compatible = "ibm,plb4", }, - { .compatible = "ibm,opb", }, - { .compatible = "ibm,ebc", }, - {}, -}; - -static int __init sequoia_device_probe(void) -{ - of_platform_bus_probe(NULL, sequoia_of_bus, NULL); - - return 0; -} -machine_device_initcall(sequoia, sequoia_device_probe); - -static int __init sequoia_probe(void) -{ - unsigned long root = of_get_flat_dt_root(); - - if (!of_flat_dt_is_compatible(root, "amcc,sequoia")) - return 0; - - ppc_pci_flags = PPC_PCI_REASSIGN_ALL_RSRC; - - return 1; -} - -define_machine(sequoia) { - .name = "Sequoia", - .probe = sequoia_probe, - .progress = udbg_progress, - .init_IRQ = uic_init_tree, - .get_irq = uic_get_irq, - .restart = ppc4xx_reset_system, - .calibrate_decr = generic_calibrate_decr, -}; -- cgit v1.2.3 From 4f19a897c740e2a2e98f40b60055d56d8e437f6f Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Tue, 19 Aug 2008 11:26:53 -0400 Subject: powerpc/44x: Migrate Taishan support to ppc44x_simple Migrate the AMCC Taishan board to use the ppc44x_simple platform file. Signed-off-by: Josh Boyer --- arch/powerpc/platforms/44x/Kconfig | 1 + arch/powerpc/platforms/44x/Makefile | 1 - arch/powerpc/platforms/44x/taishan.c | 72 ------------------------------------ 3 files changed, 1 insertion(+), 73 deletions(-) delete mode 100644 arch/powerpc/platforms/44x/taishan.c (limited to 'arch') diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig index 84e2a703666..e0bea834bfe 100644 --- a/arch/powerpc/platforms/44x/Kconfig +++ b/arch/powerpc/platforms/44x/Kconfig @@ -40,6 +40,7 @@ config TAISHAN bool "Taishan" depends on 44x default n + select PPC44x_SIMPLE select 440GX select PCI help diff --git a/arch/powerpc/platforms/44x/Makefile b/arch/powerpc/platforms/44x/Makefile index a8a92c17098..698133180ae 100644 --- a/arch/powerpc/platforms/44x/Makefile +++ b/arch/powerpc/platforms/44x/Makefile @@ -1,7 +1,6 @@ obj-$(CONFIG_44x) := misc_44x.o idle.o obj-$(CONFIG_PPC44x_SIMPLE) += ppc44x_simple.o obj-$(CONFIG_EBONY) += ebony.o -obj-$(CONFIG_TAISHAN) += taishan.o obj-$(CONFIG_SAM440EP) += sam440ep.o obj-$(CONFIG_WARP) += warp.o obj-$(CONFIG_WARP) += warp-nand.o diff --git a/arch/powerpc/platforms/44x/taishan.c b/arch/powerpc/platforms/44x/taishan.c deleted file mode 100644 index 49c78b2098b..00000000000 --- a/arch/powerpc/platforms/44x/taishan.c +++ /dev/null @@ -1,72 +0,0 @@ -/* - * Taishan board specific routines based off ebony.c code - * original copyrights below - * - * Matt Porter - * Copyright 2002-2005 MontaVista Software Inc. - * - * Eugene Surovegin or - * Copyright (c) 2003-2005 Zultys Technologies - * - * Rewritten and ported to the merged powerpc tree: - * Copyright 2007 David Gibson , IBM Corporation. - * - * Modified from ebony.c for taishan: - * Copyright 2007 Hugh Blemings , IBM Corporation. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#include -#include - -#include -#include -#include -#include -#include -#include -#include - -static __initdata struct of_device_id taishan_of_bus[] = { - { .compatible = "ibm,plb4", }, - { .compatible = "ibm,opb", }, - { .compatible = "ibm,ebc", }, - {}, -}; - -static int __init taishan_device_probe(void) -{ - of_platform_bus_probe(NULL, taishan_of_bus, NULL); - - return 0; -} -machine_device_initcall(taishan, taishan_device_probe); - -/* - * Called very early, MMU is off, device-tree isn't unflattened - */ -static int __init taishan_probe(void) -{ - unsigned long root = of_get_flat_dt_root(); - - if (!of_flat_dt_is_compatible(root, "amcc,taishan")) - return 0; - - ppc_pci_flags = PPC_PCI_REASSIGN_ALL_RSRC; - - return 1; -} - -define_machine(taishan) { - .name = "Taishan", - .probe = taishan_probe, - .progress = udbg_progress, - .init_IRQ = uic_init_tree, - .get_irq = uic_get_irq, - .restart = ppc4xx_reset_system, - .calibrate_decr = generic_calibrate_decr, -}; -- cgit v1.2.3 From ded563cf458e7803536f9d7b6bc5d808a6e37f21 Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Tue, 19 Aug 2008 11:27:01 -0400 Subject: powerpc/44x: Add explicit support for AMCC Glacier Add explicit support for the AMCC Glacier eval board to Kconfig and the ppc44x_simple file. Also removes the cayonlands compatible entry from the DTS file. Signed-off-by: Josh Boyer --- arch/powerpc/boot/dts/glacier.dts | 2 +- arch/powerpc/platforms/44x/Kconfig | 11 +++++++++++ arch/powerpc/platforms/44x/ppc44x_simple.c | 1 + 3 files changed, 13 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/glacier.dts b/arch/powerpc/boot/dts/glacier.dts index 24cf0dba120..f3787a27f63 100644 --- a/arch/powerpc/boot/dts/glacier.dts +++ b/arch/powerpc/boot/dts/glacier.dts @@ -14,7 +14,7 @@ #address-cells = <2>; #size-cells = <1>; model = "amcc,glacier"; - compatible = "amcc,glacier", "amcc,canyonlands"; + compatible = "amcc,glacier"; dcr-parent = <&{/cpus/cpu@0}>; aliases { diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig index e0bea834bfe..f8ef279f325 100644 --- a/arch/powerpc/platforms/44x/Kconfig +++ b/arch/powerpc/platforms/44x/Kconfig @@ -92,6 +92,17 @@ config CANYONLANDS help This option enables support for the AMCC PPC460EX evaluation board. +config GLACIER + bool "Glacier" + depends on 44x + default n + select PPC44x_SIMPLE + select 460EX # Odd since it uses 460GT but the effects are the same + select PCI + select PPC4xx_PCI_EXPRESS + help + This option enables support for the AMCC PPC460GT evaluation board. + config YOSEMITE bool "Yosemite" depends on 44x diff --git a/arch/powerpc/platforms/44x/ppc44x_simple.c b/arch/powerpc/platforms/44x/ppc44x_simple.c index 32b0535f29f..1c064b242cf 100644 --- a/arch/powerpc/platforms/44x/ppc44x_simple.c +++ b/arch/powerpc/platforms/44x/ppc44x_simple.c @@ -52,6 +52,7 @@ machine_device_initcall(ppc44x_simple, ppc44x_device_probe); static char *board[] __initdata = { "amcc,bamboo", "amcc,cayonlands", + "amcc,glacier", "ibm,ebony", "amcc,katmai", "amcc,rainier", -- cgit v1.2.3 From 38d56f1677130004497835a776feb84f068ce22a Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Tue, 19 Aug 2008 11:27:05 -0400 Subject: powerpc/44x: Add explicit Yosemite support Add the Yosemite board to the explicitly supported list for ppc44x_simple boards and remove the compatible entry for bamboo from the DTS file. Signed-off-by: Josh Boyer --- arch/powerpc/boot/dts/yosemite.dts | 2 +- arch/powerpc/platforms/44x/ppc44x_simple.c | 3 ++- 2 files changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/yosemite.dts b/arch/powerpc/boot/dts/yosemite.dts index e39422aa0d8..1fa3cb4c4eb 100644 --- a/arch/powerpc/boot/dts/yosemite.dts +++ b/arch/powerpc/boot/dts/yosemite.dts @@ -15,7 +15,7 @@ #address-cells = <2>; #size-cells = <1>; model = "amcc,yosemite"; - compatible = "amcc,yosemite","amcc,bamboo"; + compatible = "amcc,yosemite"; dcr-parent = <&{/cpus/cpu@0}>; aliases { diff --git a/arch/powerpc/platforms/44x/ppc44x_simple.c b/arch/powerpc/platforms/44x/ppc44x_simple.c index 1c064b242cf..57e71203d0f 100644 --- a/arch/powerpc/platforms/44x/ppc44x_simple.c +++ b/arch/powerpc/platforms/44x/ppc44x_simple.c @@ -57,7 +57,8 @@ static char *board[] __initdata = { "amcc,katmai", "amcc,rainier", "amcc,sequoia", - "amcc,taishan" + "amcc,taishan", + "amcc,yosemite" }; static int __init ppc44x_probe(void) -- cgit v1.2.3 From cc2e113b4bbd415d53d8bb87a446cde6b7ce8acc Mon Sep 17 00:00:00 2001 From: Ilya Yanok Date: Mon, 1 Sep 2008 17:53:22 +1000 Subject: powerpc/4xx: Necessary fixes to PCI for 4GB RAM size The declaration of total_memory removed. Now including instead. Since total_memory is a phys_addr_t which is 64-bit on 44x and is_power_of_2() works with u32 so I just inlined (size & (size-1)) != 0 instead. Also this patch fixes default initialization: res->end should be 0x7fffffff not 0x80000000. Signed-off-by: Ilya Yanok Acked-by: Stefan Roese Signed-off-by: Josh Boyer --- arch/powerpc/sysdev/ppc4xx_pci.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/ppc4xx_pci.c b/arch/powerpc/sysdev/ppc4xx_pci.c index d5c345dbb89..5da8a44ea2f 100644 --- a/arch/powerpc/sysdev/ppc4xx_pci.c +++ b/arch/powerpc/sysdev/ppc4xx_pci.c @@ -30,14 +30,12 @@ #include #include #include +#include #include "ppc4xx_pci.h" static int dma_offset_set; -/* Move that to a useable header */ -extern unsigned long total_memory; - #define U64_TO_U32_LOW(val) ((u32)((val) & 0x00000000ffffffffULL)) #define U64_TO_U32_HIGH(val) ((u32)((val) >> 32)) @@ -105,7 +103,8 @@ static int __init ppc4xx_parse_dma_ranges(struct pci_controller *hose, /* Default */ res->start = 0; - res->end = size = 0x80000000; + size = 0x80000000; + res->end = size - 1; res->flags = IORESOURCE_MEM | IORESOURCE_PREFETCH; /* Get dma-ranges property */ @@ -167,13 +166,13 @@ static int __init ppc4xx_parse_dma_ranges(struct pci_controller *hose, */ if (size < total_memory) { printk(KERN_ERR "%s: dma-ranges too small " - "(size=%llx total_memory=%lx)\n", - hose->dn->full_name, size, total_memory); + "(size=%llx total_memory=%llx)\n", + hose->dn->full_name, size, (u64)total_memory); return -ENXIO; } /* Check we are a power of 2 size and that base is a multiple of size*/ - if (!is_power_of_2(size) || + if ((size & (size - 1)) != 0 || (res->start & (size - 1)) != 0) { printk(KERN_ERR "%s: dma-ranges unaligned\n", hose->dn->full_name); -- cgit v1.2.3 From 423da26997497f5938c0b169f1cc9762b5f3fa9f Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Sun, 7 Sep 2008 21:57:21 +0000 Subject: powerpc/44x: Add hwmon support to Sequoia device tree This patch adds support for the AD7414 temperature sensor on Sequoia PPC440EPx board. Signed-off-by: Matthias Fuchs Acked-by: Stefan Roese Signed-off-by: Josh Boyer --- arch/powerpc/boot/dts/sequoia.dts | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/sequoia.dts b/arch/powerpc/boot/dts/sequoia.dts index 72d15f075d3..3b295e8df53 100644 --- a/arch/powerpc/boot/dts/sequoia.dts +++ b/arch/powerpc/boot/dts/sequoia.dts @@ -246,13 +246,22 @@ }; IIC0: i2c@ef600700 { + #address-cells = <1>; + #size-cells = <0>; compatible = "ibm,iic-440epx", "ibm,iic"; reg = <0xef600700 0x00000014>; interrupt-parent = <&UIC0>; interrupts = <0x2 0x4>; + + hwmon@48 { + compatible = "adi,ad7414"; + reg = <0x48>; + }; }; IIC1: i2c@ef600800 { + #address-cells = <1>; + #size-cells = <0>; compatible = "ibm,iic-440epx", "ibm,iic"; reg = <0xef600800 0x00000014>; interrupt-parent = <&UIC0>; -- cgit v1.2.3 From 1b3c83e6d3b4d3001e42a9cf800c0071adf8e2c9 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Tue, 19 Aug 2008 08:34:17 +1000 Subject: powerpc: Fix duplicate test of MACIO_FLAG_SCCB_ON Evidently MACIO_FLAG_SCCA_ON was meant. Signed-off-by: Roel Kluin Acked-by: Benjamin Herrenschmidt Signed-off-by: Paul Mackerras --- arch/powerpc/platforms/powermac/feature.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/powermac/feature.c b/arch/powerpc/platforms/powermac/feature.c index 5169ecc3712..e6c0040ee79 100644 --- a/arch/powerpc/platforms/powermac/feature.c +++ b/arch/powerpc/platforms/powermac/feature.c @@ -2677,7 +2677,7 @@ static void __init probe_one_macio(const char *name, const char *compat, int typ macio_chips[i].of_node = node; macio_chips[i].type = type; macio_chips[i].base = base; - macio_chips[i].flags = MACIO_FLAG_SCCB_ON | MACIO_FLAG_SCCB_ON; + macio_chips[i].flags = MACIO_FLAG_SCCA_ON | MACIO_FLAG_SCCB_ON; macio_chips[i].name = macio_names[type]; revp = of_get_property(node, "revision-id", NULL); if (revp) -- cgit v1.2.3 From 2a9294369bd020db89bfdf78b84c3615b39a5c84 Mon Sep 17 00:00:00 2001 From: Mark Nelson Date: Fri, 22 Aug 2008 14:36:19 +1000 Subject: powerpc: Add new CPU feature: CPU_FTR_CP_USE_DCBTZ Add a new CPU feature bit, CPU_FTR_CP_USE_DCBTZ, to be added to the 64bit powerpc chips that benefit from having dcbt and dcbz instructions used in their memory copy routines. This will be used in a subsequent patch that updates copy_4K_page(). The new bit is added to Cell, PPC970 and Power4 because they show better performance with the new copy_4K_page() when dcbt and dcbz instructions are used. Signed-off-by: Mark Nelson Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/cputable.h | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/cputable.h b/arch/powerpc/include/asm/cputable.h index f99813f1ede..1e94b07a020 100644 --- a/arch/powerpc/include/asm/cputable.h +++ b/arch/powerpc/include/asm/cputable.h @@ -193,6 +193,7 @@ extern const char *powerpc_base_platform; #define CPU_FTR_NO_SLBIE_B LONG_ASM_CONST(0x0008000000000000) #define CPU_FTR_VSX LONG_ASM_CONST(0x0010000000000000) #define CPU_FTR_SAO LONG_ASM_CONST(0x0020000000000000) +#define CPU_FTR_CP_USE_DCBTZ LONG_ASM_CONST(0x0040000000000000) #ifndef __ASSEMBLY__ @@ -388,10 +389,11 @@ extern const char *powerpc_base_platform; CPU_FTR_MMCRA | CPU_FTR_CTRL) #define CPU_FTRS_POWER4 (CPU_FTR_USE_TB | CPU_FTR_LWSYNC | \ CPU_FTR_HPTE_TABLE | CPU_FTR_PPCAS_ARCH_V2 | CPU_FTR_CTRL | \ - CPU_FTR_MMCRA) + CPU_FTR_MMCRA | CPU_FTR_CP_USE_DCBTZ) #define CPU_FTRS_PPC970 (CPU_FTR_USE_TB | CPU_FTR_LWSYNC | \ CPU_FTR_HPTE_TABLE | CPU_FTR_PPCAS_ARCH_V2 | CPU_FTR_CTRL | \ - CPU_FTR_ALTIVEC_COMP | CPU_FTR_CAN_NAP | CPU_FTR_MMCRA) + CPU_FTR_ALTIVEC_COMP | CPU_FTR_CAN_NAP | CPU_FTR_MMCRA | \ + CPU_FTR_CP_USE_DCBTZ) #define CPU_FTRS_POWER5 (CPU_FTR_USE_TB | CPU_FTR_LWSYNC | \ CPU_FTR_HPTE_TABLE | CPU_FTR_PPCAS_ARCH_V2 | CPU_FTR_CTRL | \ CPU_FTR_MMCRA | CPU_FTR_SMT | \ @@ -412,7 +414,8 @@ extern const char *powerpc_base_platform; #define CPU_FTRS_CELL (CPU_FTR_USE_TB | CPU_FTR_LWSYNC | \ CPU_FTR_HPTE_TABLE | CPU_FTR_PPCAS_ARCH_V2 | CPU_FTR_CTRL | \ CPU_FTR_ALTIVEC_COMP | CPU_FTR_MMCRA | CPU_FTR_SMT | \ - CPU_FTR_PAUSE_ZERO | CPU_FTR_CI_LARGE_PAGE | CPU_FTR_CELL_TB_BUG) + CPU_FTR_PAUSE_ZERO | CPU_FTR_CI_LARGE_PAGE | \ + CPU_FTR_CELL_TB_BUG | CPU_FTR_CP_USE_DCBTZ) #define CPU_FTRS_PA6T (CPU_FTR_USE_TB | CPU_FTR_LWSYNC | \ CPU_FTR_HPTE_TABLE | CPU_FTR_PPCAS_ARCH_V2 | \ CPU_FTR_ALTIVEC_COMP | CPU_FTR_CI_LARGE_PAGE | \ -- cgit v1.2.3 From 57dda6ef5bd5b9e60410477ad29e654097e2cca1 Mon Sep 17 00:00:00 2001 From: Mark Nelson Date: Fri, 22 Aug 2008 14:39:00 +1000 Subject: powerpc: New copy_4K_page() This new copy_4K_page() function was originally tuned for the best performance on the Cell processor, but after testing on more 64bit powerpc chips it was found that with a small modification it either matched the performance offered by the current mainline version or bettered it by a small amount. It was found that on a Cell-based QS22 blade the amount of system time measured when compiling a 2.6.26 pseries_defconfig decreased by 4%. Using the same test, a 4-way 970MP machine saw a decrease of 2% in system time. No noticeable change was seen on Power4, Power5 or Power6. The 4096 byte page is copied in thirty-two 128 byte strides. An initial setup loop executes dcbt instructions for the whole source page and dcbz instructions for the whole destination page. To do this, the cache line size is retrieved from ppc64_caches. A new CPU feature bit, CPU_FTR_CP_USE_DCBTZ, (introduced in the previous patch) is used to make the modification to this new copy routine - on Power4, 970 and Cell the feature bit is set so the setup loop is executed, but on all other 64bit chips the setup loop is nop'ed out. Signed-off-by: Mark Nelson Signed-off-by: Paul Mackerras --- arch/powerpc/lib/copypage_64.S | 198 +++++++++++++++++++---------------------- 1 file changed, 93 insertions(+), 105 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/lib/copypage_64.S b/arch/powerpc/lib/copypage_64.S index f9837f44ac0..75f3267fdc3 100644 --- a/arch/powerpc/lib/copypage_64.S +++ b/arch/powerpc/lib/copypage_64.S @@ -1,5 +1,5 @@ /* - * Copyright (C) 2002 Paul Mackerras, IBM Corp. + * Copyright (C) 2008 Mark Nelson, IBM Corp. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -8,112 +8,100 @@ */ #include #include +#include + + .section ".toc","aw" +PPC64_CACHES: + .tc ppc64_caches[TC],ppc64_caches + .section ".text" + _GLOBAL(copy_4K_page) - std r31,-8(1) - std r30,-16(1) - std r29,-24(1) - std r28,-32(1) - std r27,-40(1) - std r26,-48(1) - std r25,-56(1) - std r24,-64(1) - std r23,-72(1) - std r22,-80(1) - std r21,-88(1) - std r20,-96(1) - li r5,4096/32 - 1 + li r5,4096 /* 4K page size */ +BEGIN_FTR_SECTION + ld r10,PPC64_CACHES@toc(r2) + lwz r11,DCACHEL1LOGLINESIZE(r10) /* log2 of cache line size */ + lwz r12,DCACHEL1LINESIZE(r10) /* get cache line size */ + li r9,0 + srd r8,r5,r11 + + mtctr r8 +setup: + dcbt r9,r4 + dcbz r9,r3 + add r9,r9,r12 + bdnz setup +END_FTR_SECTION_IFSET(CPU_FTR_CP_USE_DCBTZ) addi r3,r3,-8 - li r12,5 -0: addi r5,r5,-24 - mtctr r12 - ld r22,640(4) - ld r21,512(4) - ld r20,384(4) - ld r11,256(4) - ld r9,128(4) - ld r7,0(4) - ld r25,648(4) - ld r24,520(4) - ld r23,392(4) - ld r10,264(4) - ld r8,136(4) - ldu r6,8(4) - cmpwi r5,24 -1: std r22,648(3) - std r21,520(3) - std r20,392(3) - std r11,264(3) - std r9,136(3) - std r7,8(3) - ld r28,648(4) - ld r27,520(4) - ld r26,392(4) - ld r31,264(4) - ld r30,136(4) - ld r29,8(4) - std r25,656(3) - std r24,528(3) - std r23,400(3) - std r10,272(3) - std r8,144(3) - std r6,16(3) - ld r22,656(4) - ld r21,528(4) - ld r20,400(4) - ld r11,272(4) - ld r9,144(4) - ld r7,16(4) - std r28,664(3) - std r27,536(3) - std r26,408(3) - std r31,280(3) - std r30,152(3) - stdu r29,24(3) - ld r25,664(4) - ld r24,536(4) - ld r23,408(4) - ld r10,280(4) - ld r8,152(4) - ldu r6,24(4) + srdi r8,r5,7 /* page is copied in 128 byte strides */ + addi r8,r8,-1 /* one stride copied outside loop */ + + mtctr r8 + + ld r5,0(r4) + ld r6,8(r4) + ld r7,16(r4) + ldu r8,24(r4) +1: std r5,8(r3) + ld r9,8(r4) + std r6,16(r3) + ld r10,16(r4) + std r7,24(r3) + ld r11,24(r4) + std r8,32(r3) + ld r12,32(r4) + std r9,40(r3) + ld r5,40(r4) + std r10,48(r3) + ld r6,48(r4) + std r11,56(r3) + ld r7,56(r4) + std r12,64(r3) + ld r8,64(r4) + std r5,72(r3) + ld r9,72(r4) + std r6,80(r3) + ld r10,80(r4) + std r7,88(r3) + ld r11,88(r4) + std r8,96(r3) + ld r12,96(r4) + std r9,104(r3) + ld r5,104(r4) + std r10,112(r3) + ld r6,112(r4) + std r11,120(r3) + ld r7,120(r4) + stdu r12,128(r3) + ldu r8,128(r4) bdnz 1b - std r22,648(3) - std r21,520(3) - std r20,392(3) - std r11,264(3) - std r9,136(3) - std r7,8(3) - addi r4,r4,640 - addi r3,r3,648 - bge 0b - mtctr r5 - ld r7,0(4) - ld r8,8(4) - ldu r9,16(4) -3: ld r10,8(4) - std r7,8(3) - ld r7,16(4) - std r8,16(3) - ld r8,24(4) - std r9,24(3) - ldu r9,32(4) - stdu r10,32(3) - bdnz 3b -4: ld r10,8(4) - std r7,8(3) - std r8,16(3) - std r9,24(3) - std r10,32(3) -9: ld r20,-96(1) - ld r21,-88(1) - ld r22,-80(1) - ld r23,-72(1) - ld r24,-64(1) - ld r25,-56(1) - ld r26,-48(1) - ld r27,-40(1) - ld r28,-32(1) - ld r29,-24(1) - ld r30,-16(1) - ld r31,-8(1) + + std r5,8(r3) + ld r9,8(r4) + std r6,16(r3) + ld r10,16(r4) + std r7,24(r3) + ld r11,24(r4) + std r8,32(r3) + ld r12,32(r4) + std r9,40(r3) + ld r5,40(r4) + std r10,48(r3) + ld r6,48(r4) + std r11,56(r3) + ld r7,56(r4) + std r12,64(r3) + ld r8,64(r4) + std r5,72(r3) + ld r9,72(r4) + std r6,80(r3) + ld r10,80(r4) + std r7,88(r3) + ld r11,88(r4) + std r8,96(r3) + ld r12,96(r4) + std r9,104(r3) + std r10,112(r3) + std r11,120(r3) + std r12,128(r3) blr -- cgit v1.2.3 From 525c411d400603665f8416f7e84bb14a43830027 Mon Sep 17 00:00:00 2001 From: Nathan Fontenot Date: Tue, 26 Aug 2008 05:33:34 +1000 Subject: powerpc: Check rc of notifier chain for memory remove The return code from invocation of the notifier for pSeries_reconfig_chain during update of the device tree is not checked. This causes writes to /proc/ppc64/ofdt to update memory properties (i.e. ibm,dyamic-reconfiguration-memory) to always return success, instead of the result of the notifier chain. This happens specifically when we remove/add memory from the device tree on machines using memory specified in the ibm,dynamic-reconfiguration-memory property of the device tree. Signed-off-by: Nathan Fontenot Signed-off-by: Paul Mackerras --- arch/powerpc/platforms/pseries/reconfig.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/reconfig.c b/arch/powerpc/platforms/pseries/reconfig.c index 7637bd38c79..c591a25b0b0 100644 --- a/arch/powerpc/platforms/pseries/reconfig.c +++ b/arch/powerpc/platforms/pseries/reconfig.c @@ -466,11 +466,11 @@ static int do_update_property(char *buf, size_t bufsize) else action = PSERIES_DRCONF_MEM_REMOVE; - blocking_notifier_call_chain(&pSeries_reconfig_chain, - action, value); + rc = blocking_notifier_call_chain(&pSeries_reconfig_chain, + action, value); } - return 0; + return rc; } /** -- cgit v1.2.3 From cf00085d8045cddd80a8aabad97de96fa8131793 Mon Sep 17 00:00:00 2001 From: Chandru Date: Sat, 30 Aug 2008 00:28:16 +1000 Subject: powerpc: Add support for dynamic reconfiguration memory in kexec/kdump kernels Kdump kernel needs to use only those memory regions that it is allowed to use (crashkernel, rtas, tce, etc.). Each of these regions have their own sizes and are currently added under 'linux,usable-memory' property under each memory@xxx node of the device tree. The ibm,dynamic-memory property of ibm,dynamic-reconfiguration-memory node (on POWER6) now stores in it the representation for most of the logical memory blocks with the size of each memory block being a constant (lmb_size). If one or more or part of the above mentioned regions lie under one of the lmb from ibm,dynamic-memory property, there is a need to identify those regions within the given lmb. This makes the kernel recognize a new 'linux,drconf-usable-memory' property added by kexec-tools. Each entry in this property is of the form of a count followed by that many (base, size) pairs for the above mentioned regions. The number of cells in the count value is given by the #size-cells property of the root node. Signed-off-by: Chandru Siddalingappa Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/prom.c | 40 ++++++++++++++++++++---- arch/powerpc/mm/numa.c | 77 ++++++++++++++++++++++++++++++++++++---------- 2 files changed, 95 insertions(+), 22 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/prom.c b/arch/powerpc/kernel/prom.c index 87d83c56b31..09455e1c27c 100644 --- a/arch/powerpc/kernel/prom.c +++ b/arch/powerpc/kernel/prom.c @@ -888,9 +888,10 @@ static u64 __init dt_mem_next_cell(int s, cell_t **cellp) */ static int __init early_init_dt_scan_drconf_memory(unsigned long node) { - cell_t *dm, *ls; + cell_t *dm, *ls, *usm; unsigned long l, n, flags; u64 base, size, lmb_size; + unsigned int is_kexec_kdump = 0, rngs; ls = (cell_t *)of_get_flat_dt_prop(node, "ibm,lmb-size", &l); if (ls == NULL || l < dt_root_size_cells * sizeof(cell_t)) @@ -905,6 +906,12 @@ static int __init early_init_dt_scan_drconf_memory(unsigned long node) if (l < (n * (dt_root_addr_cells + 4) + 1) * sizeof(cell_t)) return 0; + /* check if this is a kexec/kdump kernel. */ + usm = (cell_t *)of_get_flat_dt_prop(node, "linux,drconf-usable-memory", + &l); + if (usm != NULL) + is_kexec_kdump = 1; + for (; n != 0; --n) { base = dt_mem_next_cell(dt_root_addr_cells, &dm); flags = dm[3]; @@ -915,13 +922,34 @@ static int __init early_init_dt_scan_drconf_memory(unsigned long node) if ((flags & 0x80) || !(flags & 0x8)) continue; size = lmb_size; - if (iommu_is_off) { - if (base >= 0x80000000ul) + rngs = 1; + if (is_kexec_kdump) { + /* + * For each lmb in ibm,dynamic-memory, a corresponding + * entry in linux,drconf-usable-memory property contains + * a counter 'p' followed by 'p' (base, size) duple. + * Now read the counter from + * linux,drconf-usable-memory property + */ + rngs = dt_mem_next_cell(dt_root_size_cells, &usm); + if (!rngs) /* there are no (base, size) duple */ continue; - if ((base + size) > 0x80000000ul) - size = 0x80000000ul - base; } - lmb_add(base, size); + do { + if (is_kexec_kdump) { + base = dt_mem_next_cell(dt_root_addr_cells, + &usm); + size = dt_mem_next_cell(dt_root_size_cells, + &usm); + } + if (iommu_is_off) { + if (base >= 0x80000000ul) + continue; + if ((base + size) > 0x80000000ul) + size = 0x80000000ul - base; + } + lmb_add(base, size); + } while (--rngs); } lmb_dump_all(); return 0; diff --git a/arch/powerpc/mm/numa.c b/arch/powerpc/mm/numa.c index d9a18135133..be05457631d 100644 --- a/arch/powerpc/mm/numa.c +++ b/arch/powerpc/mm/numa.c @@ -150,6 +150,21 @@ static const int *of_get_associativity(struct device_node *dev) return of_get_property(dev, "ibm,associativity", NULL); } +/* + * Returns the property linux,drconf-usable-memory if + * it exists (the property exists only in kexec/kdump kernels, + * added by kexec-tools) + */ +static const u32 *of_get_usable_memory(struct device_node *memory) +{ + const u32 *prop; + u32 len; + prop = of_get_property(memory, "linux,drconf-usable-memory", &len); + if (!prop || len < sizeof(unsigned int)) + return 0; + return prop; +} + /* Returns nid in the range [0..MAX_NUMNODES-1], or -1 if no useful numa * info is found. */ @@ -486,15 +501,30 @@ static unsigned long __init numa_enforce_memory_limit(unsigned long start, return lmb_end_of_DRAM() - start; } +/* + * Reads the counter for a given entry in + * linux,drconf-usable-memory property + */ +static inline int __init read_usm_ranges(const u32 **usm) +{ + /* + * For each lmb in ibm,dynamic-memory a corresponding + * entry in linux,drconf-usable-memory property contains + * a counter followed by that many (base, size) duple. + * read the counter from linux,drconf-usable-memory + */ + return read_n_cells(n_mem_size_cells, usm); +} + /* * Extract NUMA information from the ibm,dynamic-reconfiguration-memory * node. This assumes n_mem_{addr,size}_cells have been set. */ static void __init parse_drconf_memory(struct device_node *memory) { - const u32 *dm; - unsigned int n, rc; - unsigned long lmb_size, size; + const u32 *dm, *usm; + unsigned int n, rc, ranges, is_kexec_kdump = 0; + unsigned long lmb_size, base, size, sz; int nid; struct assoc_arrays aa; @@ -510,6 +540,11 @@ static void __init parse_drconf_memory(struct device_node *memory) if (rc) return; + /* check if this is a kexec/kdump kernel */ + usm = of_get_usable_memory(memory); + if (usm != NULL) + is_kexec_kdump = 1; + for (; n != 0; --n) { struct of_drconf_cell drmem; @@ -521,21 +556,31 @@ static void __init parse_drconf_memory(struct device_node *memory) || !(drmem.flags & DRCONF_MEM_ASSIGNED)) continue; - nid = of_drconf_to_nid_single(&drmem, &aa); + base = drmem.base_addr; + size = lmb_size; + ranges = 1; - fake_numa_create_new_node( - ((drmem.base_addr + lmb_size) >> PAGE_SHIFT), + if (is_kexec_kdump) { + ranges = read_usm_ranges(&usm); + if (!ranges) /* there are no (base, size) duple */ + continue; + } + do { + if (is_kexec_kdump) { + base = read_n_cells(n_mem_addr_cells, &usm); + size = read_n_cells(n_mem_size_cells, &usm); + } + nid = of_drconf_to_nid_single(&drmem, &aa); + fake_numa_create_new_node( + ((base + size) >> PAGE_SHIFT), &nid); - - node_set_online(nid); - - size = numa_enforce_memory_limit(drmem.base_addr, lmb_size); - if (!size) - continue; - - add_active_range(nid, drmem.base_addr >> PAGE_SHIFT, - (drmem.base_addr >> PAGE_SHIFT) - + (size >> PAGE_SHIFT)); + node_set_online(nid); + sz = numa_enforce_memory_limit(base, size); + if (sz) + add_active_range(nid, base >> PAGE_SHIFT, + (base >> PAGE_SHIFT) + + (sz >> PAGE_SHIFT)); + } while (--ranges); } } -- cgit v1.2.3 From 9a95516740c924675d52c472d7d170c62eab176c Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Sat, 30 Aug 2008 11:39:26 +1000 Subject: powerpc: Rearrange head_64.S to move interrupt handler code to the beginning This rearranges head_64.S so that we have all the first-level exception prologs together starting at 0x100, followed by all the second-level handlers that are invoked from the first-level prologs, followed by other code. This doesn't make any functional change but will make following changes for relocatable kernel support easier. Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/head_64.S | 203 ++++++++++++++++++++++-------------------- 1 file changed, 106 insertions(+), 97 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S index cc8fb474d52..27935d1ab6a 100644 --- a/arch/powerpc/kernel/head_64.S +++ b/arch/powerpc/kernel/head_64.S @@ -325,16 +325,32 @@ do_stab_bolted_pSeries: mfspr r12,SPRN_SPRG2 EXCEPTION_PROLOG_PSERIES(PACA_EXSLB, .do_stab_bolted) +#ifdef CONFIG_PPC_PSERIES +/* + * Vectors for the FWNMI option. Share common code. + */ + .globl system_reset_fwnmi + .align 7 +system_reset_fwnmi: + HMT_MEDIUM + mtspr SPRN_SPRG1,r13 /* save r13 */ + EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, system_reset_common) + + .globl machine_check_fwnmi + .align 7 +machine_check_fwnmi: + HMT_MEDIUM + mtspr SPRN_SPRG1,r13 /* save r13 */ + EXCEPTION_PROLOG_PSERIES(PACA_EXMC, machine_check_common) + +#endif /* CONFIG_PPC_PSERIES */ + +#ifdef __DISABLED__ /* - * We have some room here we use that to put - * the peries slb miss user trampoline code so it's reasonably - * away from slb_miss_user_common to avoid problems with rfid - * * This is used for when the SLB miss handler has to go virtual, * which doesn't happen for now anymore but will once we re-implement * dynamic VSIDs for shared page tables */ -#ifdef __DISABLED__ slb_miss_user_pseries: std r10,PACA_EXGEN+EX_R10(r13) std r11,PACA_EXGEN+EX_R11(r13) @@ -357,25 +373,14 @@ slb_miss_user_pseries: b . /* prevent spec. execution */ #endif /* __DISABLED__ */ -#ifdef CONFIG_PPC_PSERIES + .align 7 + .globl __end_interrupts +__end_interrupts: + /* - * Vectors for the FWNMI option. Share common code. + * Code from here down to __end_handlers is invoked from the + * exception prologs above. */ - .globl system_reset_fwnmi - .align 7 -system_reset_fwnmi: - HMT_MEDIUM - mtspr SPRN_SPRG1,r13 /* save r13 */ - EXCEPTION_PROLOG_PSERIES_FORCE_64BIT(PACA_EXGEN, system_reset_common) - - .globl machine_check_fwnmi - .align 7 -machine_check_fwnmi: - HMT_MEDIUM - mtspr SPRN_SPRG1,r13 /* save r13 */ - EXCEPTION_PROLOG_PSERIES_FORCE_64BIT(PACA_EXMC, machine_check_common) - -#endif /* CONFIG_PPC_PSERIES */ /*** Common interrupt handlers ***/ @@ -456,65 +461,6 @@ bad_stack: bl .kernel_bad_stack b 1b -/* - * Return from an exception with minimal checks. - * The caller is assumed to have done EXCEPTION_PROLOG_COMMON. - * If interrupts have been enabled, or anything has been - * done that might have changed the scheduling status of - * any task or sent any task a signal, you should use - * ret_from_except or ret_from_except_lite instead of this. - */ -fast_exc_return_irq: /* restores irq state too */ - ld r3,SOFTE(r1) - TRACE_AND_RESTORE_IRQ(r3); - ld r12,_MSR(r1) - rldicl r4,r12,49,63 /* get MSR_EE to LSB */ - stb r4,PACAHARDIRQEN(r13) /* restore paca->hard_enabled */ - b 1f - - .globl fast_exception_return -fast_exception_return: - ld r12,_MSR(r1) -1: ld r11,_NIP(r1) - andi. r3,r12,MSR_RI /* check if RI is set */ - beq- unrecov_fer - -#ifdef CONFIG_VIRT_CPU_ACCOUNTING - andi. r3,r12,MSR_PR - beq 2f - ACCOUNT_CPU_USER_EXIT(r3, r4) -2: -#endif - - ld r3,_CCR(r1) - ld r4,_LINK(r1) - ld r5,_CTR(r1) - ld r6,_XER(r1) - mtcr r3 - mtlr r4 - mtctr r5 - mtxer r6 - REST_GPR(0, r1) - REST_8GPRS(2, r1) - - mfmsr r10 - rldicl r10,r10,48,1 /* clear EE */ - rldicr r10,r10,16,61 /* clear RI (LE is 0 already) */ - mtmsrd r10,1 - - mtspr SPRN_SRR1,r12 - mtspr SPRN_SRR0,r11 - REST_4GPRS(10, r1) - ld r1,GPR1(r1) - rfid - b . /* prevent speculative execution */ - -unrecov_fer: - bl .save_nvgprs -1: addi r3,r1,STACK_FRAME_OVERHEAD - bl .unrecoverable_exception - b 1b - /* * Here r13 points to the paca, r9 contains the saved CR, * SRR0 and SRR1 are saved in r11 and r12, @@ -766,6 +712,85 @@ END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC) bl .altivec_unavailable_exception b .ret_from_except + .align 7 + .globl vsx_unavailable_common +vsx_unavailable_common: + EXCEPTION_PROLOG_COMMON(0xf40, PACA_EXGEN) +#ifdef CONFIG_VSX +BEGIN_FTR_SECTION + bne .load_up_vsx +1: +END_FTR_SECTION_IFSET(CPU_FTR_VSX) +#endif + bl .save_nvgprs + addi r3,r1,STACK_FRAME_OVERHEAD + ENABLE_INTS + bl .vsx_unavailable_exception + b .ret_from_except + + .align 7 + .globl __end_handlers +__end_handlers: + +/* + * Return from an exception with minimal checks. + * The caller is assumed to have done EXCEPTION_PROLOG_COMMON. + * If interrupts have been enabled, or anything has been + * done that might have changed the scheduling status of + * any task or sent any task a signal, you should use + * ret_from_except or ret_from_except_lite instead of this. + */ +fast_exc_return_irq: /* restores irq state too */ + ld r3,SOFTE(r1) + TRACE_AND_RESTORE_IRQ(r3); + ld r12,_MSR(r1) + rldicl r4,r12,49,63 /* get MSR_EE to LSB */ + stb r4,PACAHARDIRQEN(r13) /* restore paca->hard_enabled */ + b 1f + + .globl fast_exception_return +fast_exception_return: + ld r12,_MSR(r1) +1: ld r11,_NIP(r1) + andi. r3,r12,MSR_RI /* check if RI is set */ + beq- unrecov_fer + +#ifdef CONFIG_VIRT_CPU_ACCOUNTING + andi. r3,r12,MSR_PR + beq 2f + ACCOUNT_CPU_USER_EXIT(r3, r4) +2: +#endif + + ld r3,_CCR(r1) + ld r4,_LINK(r1) + ld r5,_CTR(r1) + ld r6,_XER(r1) + mtcr r3 + mtlr r4 + mtctr r5 + mtxer r6 + REST_GPR(0, r1) + REST_8GPRS(2, r1) + + mfmsr r10 + rldicl r10,r10,48,1 /* clear EE */ + rldicr r10,r10,16,61 /* clear RI (LE is 0 already) */ + mtmsrd r10,1 + + mtspr SPRN_SRR1,r12 + mtspr SPRN_SRR0,r11 + REST_4GPRS(10, r1) + ld r1,GPR1(r1) + rfid + b . /* prevent speculative execution */ + +unrecov_fer: + bl .save_nvgprs +1: addi r3,r1,STACK_FRAME_OVERHEAD + bl .unrecoverable_exception + b 1b + #ifdef CONFIG_ALTIVEC /* * load_up_altivec(unused, unused, tsk) @@ -840,22 +865,6 @@ _STATIC(load_up_altivec) blr #endif /* CONFIG_ALTIVEC */ - .align 7 - .globl vsx_unavailable_common -vsx_unavailable_common: - EXCEPTION_PROLOG_COMMON(0xf40, PACA_EXGEN) -#ifdef CONFIG_VSX -BEGIN_FTR_SECTION - bne .load_up_vsx -1: -END_FTR_SECTION_IFSET(CPU_FTR_VSX) -#endif - bl .save_nvgprs - addi r3,r1,STACK_FRAME_OVERHEAD - ENABLE_INTS - bl .vsx_unavailable_exception - b .ret_from_except - #ifdef CONFIG_VSX /* * load_up_vsx(unused, unused, tsk) -- cgit v1.2.3 From 1f6a93e4c35e75d547b51f56ba8139ab1a91628c Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Sat, 30 Aug 2008 11:40:24 +1000 Subject: powerpc: Make it possible to move the interrupt handlers away from the kernel This changes the way that the exception prologs transfer control to the handlers in 64-bit kernels with the aim of making it possible to have the prologs separate from the main body of the kernel. Now, instead of computing the address of the handler by taking the top 32 bits of the paca address (to get the 0xc0000000........ part) and ORing in something in the bottom 16 bits, we get the base address of the kernel by doing a load from the paca and add an offset. This also replaces an mfmsr and an ori to compute the MSR value for the handler with a load from the paca. That makes it unnecessary to have a separate version of EXCEPTION_PROLOG_PSERIES that forces 64-bit mode. We can no longer use a direct branches in the exception prolog code, which means that the SLB miss handlers can't branch directly to .slb_miss_realmode any more. Instead we have to compute the address and do an indirect branch. This is conditional on CONFIG_RELOCATABLE; for non-relocatable kernels we use a direct branch as before. (A later change will allow CONFIG_RELOCATABLE to be set on 64-bit powerpc.) Since the secondary CPUs on pSeries start execution in the first 0x100 bytes of real memory and then have to get to wherever the kernel is, we can't use a direct branch to get there. Instead this changes __secondary_hold_spinloop from a flag to a function pointer. When it is set to a non-NULL value, the secondary CPUs jump to the function pointed to by that value. Finally this eliminates one code difference between 32-bit and 64-bit by making __secondary_hold be the text address of the secondary CPU spinloop rather than a function descriptor for it. Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/exception.h | 42 +++------------------ arch/powerpc/include/asm/paca.h | 2 + arch/powerpc/kernel/asm-offsets.c | 2 + arch/powerpc/kernel/head_64.S | 71 ++++++++++++++++++++++++++++-------- arch/powerpc/kernel/paca.c | 2 + arch/powerpc/kernel/prom_init.c | 8 +--- arch/powerpc/kernel/setup_64.c | 9 +++-- 7 files changed, 72 insertions(+), 64 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/exception.h b/arch/powerpc/include/asm/exception.h index 329148b5acc..d3d4534e3c7 100644 --- a/arch/powerpc/include/asm/exception.h +++ b/arch/powerpc/include/asm/exception.h @@ -53,14 +53,8 @@ * low halfword of the address, but for Kdump we need the whole low * word. */ -#ifdef CONFIG_CRASH_DUMP #define LOAD_HANDLER(reg, label) \ - oris reg,reg,(label)@h; /* virt addr of handler ... */ \ - ori reg,reg,(label)@l; /* .. and the rest */ -#else -#define LOAD_HANDLER(reg, label) \ - ori reg,reg,(label)@l; /* virt addr of handler ... */ -#endif + addi reg,reg,(label)-_stext; /* virt addr of handler ... */ #define EXCEPTION_PROLOG_1(area) \ mfspr r13,SPRN_SPRG3; /* get paca address into r13 */ \ @@ -72,37 +66,12 @@ std r9,area+EX_R13(r13); \ mfcr r9 -/* - * Equal to EXCEPTION_PROLOG_PSERIES, except that it forces 64bit mode. - * The firmware calls the registered system_reset_fwnmi and - * machine_check_fwnmi handlers in 32bit mode if the cpu happens to run - * a 32bit application at the time of the event. - * This firmware bug is present on POWER4 and JS20. - */ -#define EXCEPTION_PROLOG_PSERIES_FORCE_64BIT(area, label) \ - EXCEPTION_PROLOG_1(area); \ - clrrdi r12,r13,32; /* get high part of &label */ \ - mfmsr r10; \ - /* force 64bit mode */ \ - li r11,5; /* MSR_SF_LG|MSR_ISF_LG */ \ - rldimi r10,r11,61,0; /* insert into top 3 bits */ \ - /* done 64bit mode */ \ - mfspr r11,SPRN_SRR0; /* save SRR0 */ \ - LOAD_HANDLER(r12,label) \ - ori r10,r10,MSR_IR|MSR_DR|MSR_RI; \ - mtspr SPRN_SRR0,r12; \ - mfspr r12,SPRN_SRR1; /* and SRR1 */ \ - mtspr SPRN_SRR1,r10; \ - rfid; \ - b . /* prevent speculative execution */ - #define EXCEPTION_PROLOG_PSERIES(area, label) \ EXCEPTION_PROLOG_1(area); \ - clrrdi r12,r13,32; /* get high part of &label */ \ - mfmsr r10; \ + ld r12,PACAKBASE(r13); /* get high part of &label */ \ + ld r10,PACAKMSR(r13); /* get MSR value for kernel */ \ mfspr r11,SPRN_SRR0; /* save SRR0 */ \ LOAD_HANDLER(r12,label) \ - ori r10,r10,MSR_IR|MSR_DR|MSR_RI; \ mtspr SPRN_SRR0,r12; \ mfspr r12,SPRN_SRR1; /* and SRR1 */ \ mtspr SPRN_SRR1,r10; \ @@ -210,11 +179,10 @@ label##_pSeries: \ std r10,PACA_EXGEN+EX_R13(r13); \ std r11,PACA_EXGEN+EX_R11(r13); \ std r12,PACA_EXGEN+EX_R12(r13); \ - clrrdi r12,r13,32; /* get high part of &label */ \ - mfmsr r10; \ + ld r12,PACAKBASE(r13); /* get high part of &label */ \ + ld r10,PACAKMSR(r13); /* get MSR value for kernel */ \ mfspr r11,SPRN_SRR0; /* save SRR0 */ \ LOAD_HANDLER(r12,label##_common) \ - ori r10,r10,MSR_IR|MSR_DR|MSR_RI; \ mtspr SPRN_SRR0,r12; \ mfspr r12,SPRN_SRR1; /* and SRR1 */ \ mtspr SPRN_SRR1,r10; \ diff --git a/arch/powerpc/include/asm/paca.h b/arch/powerpc/include/asm/paca.h index 6493a395508..082b3aedf14 100644 --- a/arch/powerpc/include/asm/paca.h +++ b/arch/powerpc/include/asm/paca.h @@ -62,6 +62,8 @@ struct paca_struct { u16 paca_index; /* Logical processor number */ u64 kernel_toc; /* Kernel TOC address */ + u64 kernelbase; /* Base address of kernel */ + u64 kernel_msr; /* MSR while running in kernel */ u64 stab_real; /* Absolute address of segment table */ u64 stab_addr; /* Virtual address of segment table */ void *emergency_sp; /* pointer to emergency stack */ diff --git a/arch/powerpc/kernel/asm-offsets.c b/arch/powerpc/kernel/asm-offsets.c index 92768d3006f..e9c4044012b 100644 --- a/arch/powerpc/kernel/asm-offsets.c +++ b/arch/powerpc/kernel/asm-offsets.c @@ -122,6 +122,8 @@ int main(void) DEFINE(PACASTABRR, offsetof(struct paca_struct, stab_rr)); DEFINE(PACAR1, offsetof(struct paca_struct, saved_r1)); DEFINE(PACATOC, offsetof(struct paca_struct, kernel_toc)); + DEFINE(PACAKBASE, offsetof(struct paca_struct, kernelbase)); + DEFINE(PACAKMSR, offsetof(struct paca_struct, kernel_msr)); DEFINE(PACASOFTIRQEN, offsetof(struct paca_struct, soft_enabled)); DEFINE(PACAHARDIRQEN, offsetof(struct paca_struct, hard_enabled)); DEFINE(PACASLBCACHE, offsetof(struct paca_struct, slb_cache)); diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S index 27935d1ab6a..97bb6e6f67b 100644 --- a/arch/powerpc/kernel/head_64.S +++ b/arch/powerpc/kernel/head_64.S @@ -82,7 +82,11 @@ END_FTR_SECTION(0, 1) /* Catch branch to 0 in real mode */ trap - /* Secondary processors spin on this value until it goes to 1. */ + /* Secondary processors spin on this value until it becomes nonzero. + * When it does it contains the real address of the descriptor + * of the function that the cpu should jump to to continue + * initialization. + */ .globl __secondary_hold_spinloop __secondary_hold_spinloop: .llong 0x0 @@ -109,8 +113,11 @@ __secondary_hold_acknowledge: * before the bulk of the kernel has been relocated. This code * is relocated to physical address 0x60 before prom_init is run. * All of it must fit below the first exception vector at 0x100. + * Use .globl here not _GLOBAL because we want __secondary_hold + * to be the actual text address, not a descriptor. */ -_GLOBAL(__secondary_hold) + .globl __secondary_hold +__secondary_hold: mfmsr r24 ori r24,r24,MSR_RI mtmsrd r24 /* RI on */ @@ -126,11 +133,11 @@ _GLOBAL(__secondary_hold) /* All secondary cpus wait here until told to start. */ 100: ld r4,__secondary_hold_spinloop@l(0) - cmpdi 0,r4,1 - bne 100b + cmpdi 0,r4,0 + beq 100b #if defined(CONFIG_SMP) || defined(CONFIG_KEXEC) - LOAD_REG_IMMEDIATE(r4, .generic_secondary_smp_init) + ld r4,0(r4) /* deref function descriptor */ mtctr r4 mr r3,r24 bctr @@ -147,6 +154,10 @@ exception_marker: /* * This is the start of the interrupt handlers for pSeries * This code runs with relocation off. + * Code from here to __end_interrupts gets copied down to real + * address 0x100 when we are running a relocatable kernel. + * Therefore any relative branches in this section must only + * branch to labels in this section. */ . = 0x100 .globl __start_interrupts @@ -200,7 +211,20 @@ data_access_slb_pSeries: mfspr r10,SPRN_SPRG1 std r10,PACA_EXSLB+EX_R13(r13) mfspr r12,SPRN_SRR1 /* and SRR1 */ - b .slb_miss_realmode /* Rel. branch works in real mode */ +#ifndef CONFIG_RELOCATABLE + b .slb_miss_realmode +#else + /* + * We can't just use a direct branch to .slb_miss_realmode + * because the distance from here to there depends on where + * the kernel ends up being put. + */ + mfctr r11 + ld r10,PACAKBASE(r13) + LOAD_HANDLER(r10, .slb_miss_realmode) + mtctr r10 + bctr +#endif STD_EXCEPTION_PSERIES(0x400, instruction_access) @@ -225,7 +249,15 @@ instruction_access_slb_pSeries: mfspr r10,SPRN_SPRG1 std r10,PACA_EXSLB+EX_R13(r13) mfspr r12,SPRN_SRR1 /* and SRR1 */ - b .slb_miss_realmode /* Rel. branch works in real mode */ +#ifndef CONFIG_RELOCATABLE + b .slb_miss_realmode +#else + mfctr r11 + ld r10,PACAKBASE(r13) + LOAD_HANDLER(r10, .slb_miss_realmode) + mtctr r10 + bctr +#endif MASKABLE_EXCEPTION_PSERIES(0x500, hardware_interrupt) STD_EXCEPTION_PSERIES(0x600, alignment) @@ -244,14 +276,12 @@ BEGIN_FTR_SECTION beq- 1f END_FTR_SECTION_IFSET(CPU_FTR_REAL_LE) mr r9,r13 - mfmsr r10 mfspr r13,SPRN_SPRG3 mfspr r11,SPRN_SRR0 - clrrdi r12,r13,32 - oris r12,r12,system_call_common@h - ori r12,r12,system_call_common@l + ld r12,PACAKBASE(r13) + ld r10,PACAKMSR(r13) + LOAD_HANDLER(r12, system_call_entry) mtspr SPRN_SRR0,r12 - ori r10,r10,MSR_IR|MSR_DR|MSR_RI mfspr r12,SPRN_SRR1 mtspr SPRN_SRR1,r10 rfid @@ -379,7 +409,10 @@ __end_interrupts: /* * Code from here down to __end_handlers is invoked from the - * exception prologs above. + * exception prologs above. Because the prologs assemble the + * addresses of these handlers using the LOAD_HANDLER macro, + * which uses an addi instruction, these handlers must be in + * the first 32k of the kernel image. */ /*** Common interrupt handlers ***/ @@ -419,6 +452,10 @@ machine_check_common: STD_EXCEPTION_COMMON(0x1800, cbe_thermal, .cbe_thermal_exception) #endif /* CONFIG_CBE_RAS */ + .align 7 +system_call_entry: + b system_call_common + /* * Here we have detected that the kernel stack pointer is bad. * R9 contains the saved CR, r13 points to the paca, @@ -562,6 +599,9 @@ unrecov_user_slb: */ _GLOBAL(slb_miss_realmode) mflr r10 +#ifdef CONFIG_RELOCATABLE + mtctr r11 +#endif stw r9,PACA_EXSLB+EX_CCR(r13) /* save CR in exc. frame */ std r10,PACA_EXSLB+EX_LR(r13) /* save LR */ @@ -612,11 +652,10 @@ BEGIN_FW_FTR_SECTION END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif /* CONFIG_PPC_ISERIES */ mfspr r11,SPRN_SRR0 - clrrdi r10,r13,32 + ld r10,PACAKBASE(r13) LOAD_HANDLER(r10,unrecov_slb) mtspr SPRN_SRR0,r10 - mfmsr r10 - ori r10,r10,MSR_IR|MSR_DR|MSR_RI + ld r10,PACAKMSR(r13) mtspr SPRN_SRR1,r10 rfid b . diff --git a/arch/powerpc/kernel/paca.c b/arch/powerpc/kernel/paca.c index c9bf17eec31..623e8c3c57f 100644 --- a/arch/powerpc/kernel/paca.c +++ b/arch/powerpc/kernel/paca.c @@ -79,6 +79,8 @@ void __init initialise_pacas(void) new_paca->lock_token = 0x8000; new_paca->paca_index = cpu; new_paca->kernel_toc = kernel_toc; + new_paca->kernelbase = KERNELBASE; + new_paca->kernel_msr = MSR_KERNEL; new_paca->hw_cpu_id = 0xffff; new_paca->slb_shadow_ptr = &slb_shadow[cpu]; new_paca->__current = &init_task; diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c index b72849ac7db..1f898858505 100644 --- a/arch/powerpc/kernel/prom_init.c +++ b/arch/powerpc/kernel/prom_init.c @@ -1321,7 +1321,7 @@ static void __init prom_initialize_tce_table(void) * * -- Cort */ -extern void __secondary_hold(void); +extern char __secondary_hold; extern unsigned long __secondary_hold_spinloop; extern unsigned long __secondary_hold_acknowledge; @@ -1342,13 +1342,7 @@ static void __init prom_hold_cpus(void) = (void *) LOW_ADDR(__secondary_hold_spinloop); unsigned long *acknowledge = (void *) LOW_ADDR(__secondary_hold_acknowledge); -#ifdef CONFIG_PPC64 - /* __secondary_hold is actually a descriptor, not the text address */ - unsigned long secondary_hold - = __pa(*PTRRELOC((unsigned long *)__secondary_hold)); -#else unsigned long secondary_hold = LOW_ADDR(__secondary_hold); -#endif prom_debug("prom_hold_cpus: start...\n"); prom_debug(" 1) spinloop = 0x%x\n", (unsigned long)spinloop); diff --git a/arch/powerpc/kernel/setup_64.c b/arch/powerpc/kernel/setup_64.c index 8b25f51f03b..843c0af210d 100644 --- a/arch/powerpc/kernel/setup_64.c +++ b/arch/powerpc/kernel/setup_64.c @@ -255,9 +255,11 @@ void early_setup_secondary(void) #endif /* CONFIG_SMP */ #if defined(CONFIG_SMP) || defined(CONFIG_KEXEC) +extern unsigned long __secondary_hold_spinloop; +extern void generic_secondary_smp_init(void); + void smp_release_cpus(void) { - extern unsigned long __secondary_hold_spinloop; unsigned long *ptr; DBG(" -> smp_release_cpus()\n"); @@ -266,12 +268,11 @@ void smp_release_cpus(void) * all now so they can start to spin on their individual paca * spinloops. For non SMP kernels, the secondary cpus never get out * of the common spinloop. - * This is useless but harmless on iSeries, secondaries are already - * waiting on their paca spinloops. */ + */ ptr = (unsigned long *)((unsigned long)&__secondary_hold_spinloop - PHYSICAL_START); - *ptr = 1; + *ptr = __pa(generic_secondary_smp_init); mb(); DBG(" <- smp_release_cpus()\n"); -- cgit v1.2.3 From e31aa453bbc4886a7bd33e5c2afa526d6f55bd7a Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Sat, 30 Aug 2008 11:41:12 +1000 Subject: powerpc: Use LOAD_REG_IMMEDIATE only for constants on 64-bit Using LOAD_REG_IMMEDIATE to get the address of kernel symbols generates 5 instructions where LOAD_REG_ADDR can do it in one, and will generate R_PPC64_ADDR16_* relocations in the output when we get to making the kernel as a position-independent executable, which we'd rather not have to handle. This changes various bits of assembly code to use LOAD_REG_ADDR when we need to get the address of a symbol, or to use suitable position-independent code for cases where we can't access the TOC for various reasons, or if we're not running at the address we were linked at. It also cleans up a few minor things; there's no reason to save and restore SRR0/1 around RTAS calls, __mmu_off can get the return address from LR more conveniently than the caller can supply it in R4 (and we already assume elsewhere that EA == RA if the MMU is on in early boot), and enable_64b_mode was using 5 instructions where 2 would do. Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/ppc_asm.h | 2 +- arch/powerpc/kernel/cpu_setup_ppc970.S | 4 +- arch/powerpc/kernel/entry_64.S | 16 ++- arch/powerpc/kernel/head_64.S | 181 +++++++++++++---------------- arch/powerpc/kernel/misc.S | 10 +- arch/powerpc/platforms/iseries/exception.S | 23 ++-- 6 files changed, 110 insertions(+), 126 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/ppc_asm.h b/arch/powerpc/include/asm/ppc_asm.h index 0966899d974..c4a029ccb4d 100644 --- a/arch/powerpc/include/asm/ppc_asm.h +++ b/arch/powerpc/include/asm/ppc_asm.h @@ -268,7 +268,7 @@ n: * Loads the value of the constant expression 'expr' into register 'rn' * using immediate instructions only. Use this when it's important not * to reference other data (i.e. on ppc64 when the TOC pointer is not - * valid). + * valid) and when 'expr' is a constant or absolute address. * * LOAD_REG_ADDR(rn, name) * Loads the address of label 'name' into register 'rn'. Use this when diff --git a/arch/powerpc/kernel/cpu_setup_ppc970.S b/arch/powerpc/kernel/cpu_setup_ppc970.S index bf118c38575..27f2507279d 100644 --- a/arch/powerpc/kernel/cpu_setup_ppc970.S +++ b/arch/powerpc/kernel/cpu_setup_ppc970.S @@ -110,7 +110,7 @@ load_hids: isync /* Save away cpu state */ - LOAD_REG_IMMEDIATE(r5,cpu_state_storage) + LOAD_REG_ADDR(r5,cpu_state_storage) /* Save HID0,1,4 and 5 */ mfspr r3,SPRN_HID0 @@ -134,7 +134,7 @@ _GLOBAL(__restore_cpu_ppc970) rldicl. r0,r0,4,63 beqlr - LOAD_REG_IMMEDIATE(r5,cpu_state_storage) + LOAD_REG_ADDR(r5,cpu_state_storage) /* Before accessing memory, we make sure rm_ci is clear */ li r0,0 mfspr r3,SPRN_HID4 diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S index 55445f1dba8..fd8b4bae9b0 100644 --- a/arch/powerpc/kernel/entry_64.S +++ b/arch/powerpc/kernel/entry_64.S @@ -690,10 +690,6 @@ _GLOBAL(enter_rtas) std r7,_DAR(r1) mfdsisr r8 std r8,_DSISR(r1) - mfsrr0 r9 - std r9,_SRR0(r1) - mfsrr1 r10 - std r10,_SRR1(r1) /* Temporary workaround to clear CR until RTAS can be modified to * ignore all bits. @@ -754,6 +750,10 @@ _STATIC(rtas_return_loc) mfspr r4,SPRN_SPRG3 /* Get PACA */ clrldi r4,r4,2 /* convert to realmode address */ + bcl 20,31,$+4 +0: mflr r3 + ld r3,(1f-0b)(r3) /* get &.rtas_restore_regs */ + mfmsr r6 li r0,MSR_RI andc r6,r6,r0 @@ -761,7 +761,6 @@ _STATIC(rtas_return_loc) mtmsrd r6 ld r1,PACAR1(r4) /* Restore our SP */ - LOAD_REG_IMMEDIATE(r3,.rtas_restore_regs) ld r4,PACASAVEDMSR(r4) /* Restore our MSR */ mtspr SPRN_SRR0,r3 @@ -769,6 +768,9 @@ _STATIC(rtas_return_loc) rfid b . /* prevent speculative execution */ + .align 3 +1: .llong .rtas_restore_regs + _STATIC(rtas_restore_regs) /* relocation is on at this point */ REST_GPR(2, r1) /* Restore the TOC */ @@ -788,10 +790,6 @@ _STATIC(rtas_restore_regs) mtdar r7 ld r8,_DSISR(r1) mtdsisr r8 - ld r9,_SRR0(r1) - mtsrr0 r9 - ld r10,_SRR1(r1) - mtsrr1 r10 addi r1,r1,RTAS_FRAME_SIZE /* Unstack our frame */ ld r0,16(r1) /* get return address */ diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S index 97bb6e6f67b..6cdfd44d8ef 100644 --- a/arch/powerpc/kernel/head_64.S +++ b/arch/powerpc/kernel/head_64.S @@ -128,11 +128,11 @@ __secondary_hold: /* Tell the master cpu we're here */ /* Relocation is off & we are located at an address less */ /* than 0x100, so only need to grab low order offset. */ - std r24,__secondary_hold_acknowledge@l(0) + std r24,__secondary_hold_acknowledge-_stext(0) sync /* All secondary cpus wait here until told to start. */ -100: ld r4,__secondary_hold_spinloop@l(0) +100: ld r4,__secondary_hold_spinloop-_stext(0) cmpdi 0,r4,0 beq 100b @@ -1223,11 +1223,14 @@ _GLOBAL(generic_secondary_smp_init) /* turn on 64-bit mode */ bl .enable_64b_mode + /* get the TOC pointer (real address) */ + bl .relative_toc + /* Set up a paca value for this processor. Since we have the * physical cpu id in r24, we need to search the pacas to find * which logical id maps to our physical one. */ - LOAD_REG_IMMEDIATE(r13, paca) /* Get base vaddr of paca array */ + LOAD_REG_ADDR(r13, paca) /* Get base vaddr of paca array */ li r5,0 /* logical cpu id */ 1: lhz r6,PACAHWCPUID(r13) /* Load HW procid from paca */ cmpw r6,r24 /* Compare to our id */ @@ -1256,7 +1259,7 @@ _GLOBAL(generic_secondary_smp_init) sync /* order paca.run and cur_cpu_spec */ /* See if we need to call a cpu state restore handler */ - LOAD_REG_IMMEDIATE(r23, cur_cpu_spec) + LOAD_REG_ADDR(r23, cur_cpu_spec) ld r23,0(r23) ld r23,CPU_SPEC_RESTORE(r23) cmpdi 0,r23,0 @@ -1272,10 +1275,15 @@ _GLOBAL(generic_secondary_smp_init) b __secondary_start #endif +/* + * Turn the MMU off. + * Assumes we're mapped EA == RA if the MMU is on. + */ _STATIC(__mmu_off) mfmsr r3 andi. r0,r3,MSR_IR|MSR_DR beqlr + mflr r4 andc r3,r3,r0 mtspr SPRN_SRR0,r4 mtspr SPRN_SRR1,r3 @@ -1296,6 +1304,18 @@ _STATIC(__mmu_off) * */ _GLOBAL(__start_initialization_multiplatform) + /* Make sure we are running in 64 bits mode */ + bl .enable_64b_mode + + /* Get TOC pointer (current runtime address) */ + bl .relative_toc + + /* find out where we are now */ + bcl 20,31,$+4 +0: mflr r26 /* r26 = runtime addr here */ + addis r26,r26,(_stext - 0b)@ha + addi r26,r26,(_stext - 0b)@l /* current runtime base addr */ + /* * Are we booted from a PROM Of-type client-interface ? */ @@ -1307,9 +1327,6 @@ _GLOBAL(__start_initialization_multiplatform) mr r31,r3 mr r30,r4 - /* Make sure we are running in 64 bits mode */ - bl .enable_64b_mode - /* Setup some critical 970 SPRs before switching MMU off */ mfspr r0,SPRN_PVR srwi r0,r0,16 @@ -1324,9 +1341,7 @@ _GLOBAL(__start_initialization_multiplatform) 1: bl .__cpu_preinit_ppc970 2: - /* Switch off MMU if not already */ - LOAD_REG_IMMEDIATE(r4, .__after_prom_start - KERNELBASE) - add r4,r4,r30 + /* Switch off MMU if not already off */ bl .__mmu_off b .__after_prom_start @@ -1341,23 +1356,10 @@ _INIT_STATIC(__boot_from_prom) /* * Align the stack to 16-byte boundary * Depending on the size and layout of the ELF sections in the initial - * boot binary, the stack pointer will be unalignet on PowerMac + * boot binary, the stack pointer may be unaligned on PowerMac */ rldicr r1,r1,0,59 - /* Make sure we are running in 64 bits mode */ - bl .enable_64b_mode - - /* put a relocation offset into r3 */ - bl .reloc_offset - - LOAD_REG_IMMEDIATE(r2,__toc_start) - addi r2,r2,0x4000 - addi r2,r2,0x4000 - - /* Relocate the TOC from a virt addr to a real addr */ - add r2,r2,r3 - /* Restore parameters */ mr r3,r31 mr r4,r30 @@ -1373,53 +1375,37 @@ _INIT_STATIC(__boot_from_prom) _STATIC(__after_prom_start) /* - * We need to run with __start at physical address PHYSICAL_START. + * We need to run with _stext at physical address PHYSICAL_START. * This will leave some code in the first 256B of * real memory, which are reserved for software use. - * The remainder of the first page is loaded with the fixed - * interrupt vectors. The next two pages are filled with - * unknown exception placeholders. * * Note: This process overwrites the OF exception vectors. - * r26 == relocation offset - * r27 == KERNELBASE */ - bl .reloc_offset - mr r26,r3 - LOAD_REG_IMMEDIATE(r27, KERNELBASE) - LOAD_REG_IMMEDIATE(r3, PHYSICAL_START) /* target addr */ - - // XXX FIXME: Use phys returned by OF (r30) - add r4,r27,r26 /* source addr */ - /* current address of _start */ - /* i.e. where we are running */ - /* the source addr */ - - cmpdi r4,0 /* In some cases the loader may */ - bne 1f - b .start_here_multiplatform /* have already put us at zero */ - /* so we can skip the copy. */ -1: LOAD_REG_IMMEDIATE(r5,copy_to_here) /* # bytes of memory to copy */ - sub r5,r5,r27 - + cmpd r3,r26 /* In some cases the loader may */ + beq 9f /* have already put us at zero */ + mr r4,r26 /* source address */ + lis r5,(copy_to_here - _stext)@ha + addi r5,r5,(copy_to_here - _stext)@l /* # bytes of memory to copy */ li r6,0x100 /* Start offset, the first 0x100 */ /* bytes were copied earlier. */ bl .copy_and_flush /* copy the first n bytes */ /* this includes the code being */ /* executed here. */ - - LOAD_REG_IMMEDIATE(r0, 4f) /* Jump to the copy of this code */ - mtctr r0 /* that we just made/relocated */ + addis r8,r3,(4f - _stext)@ha /* Jump to the copy of this code */ + addi r8,r8,(4f - _stext)@l /* that we just made */ + mtctr r8 bctr -4: LOAD_REG_IMMEDIATE(r5,klimit) - add r5,r5,r26 - ld r5,0(r5) /* get the value of klimit */ - sub r5,r5,r27 +4: /* Now copy the rest of the kernel up to _end */ + addis r5,r26,(p_end - _stext)@ha + ld r5,(p_end - _stext)@l(r5) /* get _end */ bl .copy_and_flush /* copy the rest */ - b .start_here_multiplatform + +9: b .start_here_multiplatform + +p_end: .llong _end - _stext /* * Copy routine used to copy the kernel to start at physical address 0 @@ -1484,6 +1470,9 @@ _GLOBAL(pmac_secondary_start) /* turn on 64-bit mode */ bl .enable_64b_mode + /* get TOC pointer (real address) */ + bl .relative_toc + /* Copy some CPU settings from CPU 0 */ bl .__restore_cpu_ppc970 @@ -1493,10 +1482,10 @@ _GLOBAL(pmac_secondary_start) mtmsrd r3 /* RI on */ /* Set up a paca value for this processor. */ - LOAD_REG_IMMEDIATE(r4, paca) /* Get base vaddr of paca array */ - mulli r13,r24,PACA_SIZE /* Calculate vaddr of right paca */ + LOAD_REG_ADDR(r4,paca) /* Get base vaddr of paca array */ + mulli r13,r24,PACA_SIZE /* Calculate vaddr of right paca */ add r13,r13,r4 /* for this processor. */ - mtspr SPRN_SPRG3,r13 /* Save vaddr of paca in SPRG3 */ + mtspr SPRN_SPRG3,r13 /* Save vaddr of paca in SPRG3 */ /* Create a temp kernel stack for use before relocation is on. */ ld r1,PACAEMERGSP(r13) @@ -1524,9 +1513,6 @@ __secondary_start: /* Set thread priority to MEDIUM */ HMT_MEDIUM - /* Load TOC */ - ld r2,PACATOC(r13) - /* Do early setup for that CPU (stab, slb, hash table pointer) */ bl .early_setup_secondary @@ -1563,9 +1549,11 @@ END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES) /* * Running with relocation on at this point. All we want to do is - * zero the stack back-chain pointer before going into C code. + * zero the stack back-chain pointer and get the TOC virtual address + * before going into C code. */ _GLOBAL(start_secondary_prolog) + ld r2,PACATOC(r13) li r3,0 std r3,0(r1) /* Zero the stack frame pointer */ bl .start_secondary @@ -1577,34 +1565,46 @@ _GLOBAL(start_secondary_prolog) */ _GLOBAL(enable_64b_mode) mfmsr r11 /* grab the current MSR */ - li r12,1 - rldicr r12,r12,MSR_SF_LG,(63-MSR_SF_LG) - or r11,r11,r12 - li r12,1 - rldicr r12,r12,MSR_ISF_LG,(63-MSR_ISF_LG) + li r12,(MSR_SF | MSR_ISF)@highest + sldi r12,r12,48 or r11,r11,r12 mtmsrd r11 isync blr +/* + * This puts the TOC pointer into r2, offset by 0x8000 (as expected + * by the toolchain). It computes the correct value for wherever we + * are running at the moment, using position-independent code. + */ +_GLOBAL(relative_toc) + mflr r0 + bcl 20,31,$+4 +0: mflr r9 + ld r2,(p_toc - 0b)(r9) + add r2,r2,r9 + mtlr r0 + blr + +p_toc: .llong __toc_start + 0x8000 - 0b + /* * This is where the main kernel code starts. */ _INIT_STATIC(start_here_multiplatform) - /* get a new offset, now that the kernel has moved. */ - bl .reloc_offset - mr r26,r3 + /* set up the TOC (real address) */ + bl .relative_toc /* Clear out the BSS. It may have been done in prom_init, * already but that's irrelevant since prom_init will soon * be detached from the kernel completely. Besides, we need * to clear it now for kexec-style entry. */ - LOAD_REG_IMMEDIATE(r11,__bss_stop) - LOAD_REG_IMMEDIATE(r8,__bss_start) + LOAD_REG_ADDR(r11,__bss_stop) + LOAD_REG_ADDR(r8,__bss_start) sub r11,r11,r8 /* bss size */ addi r11,r11,7 /* round up to an even double word */ - rldicl. r11,r11,61,3 /* shift right by 3 */ + srdi. r11,r11,3 /* shift right by 3 */ beq 4f addi r8,r8,-8 li r0,0 @@ -1617,35 +1617,28 @@ _INIT_STATIC(start_here_multiplatform) ori r6,r6,MSR_RI mtmsrd r6 /* RI on */ - /* The following gets the stack and TOC set up with the regs */ + /* The following gets the stack set up with the regs */ /* pointing to the real addr of the kernel stack. This is */ /* all done to support the C function call below which sets */ /* up the htab. This is done because we have relocated the */ /* kernel but are still running in real mode. */ - LOAD_REG_IMMEDIATE(r3,init_thread_union) - add r3,r3,r26 + LOAD_REG_ADDR(r3,init_thread_union) - /* set up a stack pointer (physical address) */ + /* set up a stack pointer */ addi r1,r3,THREAD_SIZE li r0,0 stdu r0,-STACK_FRAME_OVERHEAD(r1) - /* set up the TOC (physical address) */ - LOAD_REG_IMMEDIATE(r2,__toc_start) - addi r2,r2,0x4000 - addi r2,r2,0x4000 - add r2,r2,r26 - /* Do very early kernel initializations, including initial hash table, * stab and slb setup before we turn on relocation. */ /* Restore parameters passed from prom_init/kexec */ mr r3,r31 - bl .early_setup + bl .early_setup /* also sets r13 and SPRG3 */ - LOAD_REG_IMMEDIATE(r3, .start_here_common) - LOAD_REG_IMMEDIATE(r4, MSR_KERNEL) + LOAD_REG_ADDR(r3, .start_here_common) + ld r4,PACAKMSR(r13) mtspr SPRN_SRR0,r3 mtspr SPRN_SRR1,r4 rfid @@ -1654,20 +1647,10 @@ _INIT_STATIC(start_here_multiplatform) /* This is where all platforms converge execution */ _INIT_GLOBAL(start_here_common) /* relocation is on at this point */ + std r1,PACAKSAVE(r13) - /* The following code sets up the SP and TOC now that we are */ - /* running with translation enabled. */ - - LOAD_REG_IMMEDIATE(r3,init_thread_union) - - /* set up the stack */ - addi r1,r3,THREAD_SIZE - li r0,0 - stdu r0,-STACK_FRAME_OVERHEAD(r1) - - /* Load the TOC */ + /* Load the TOC (virtual address) */ ld r2,PACATOC(r13) - std r1,PACAKSAVE(r13) bl .setup_system diff --git a/arch/powerpc/kernel/misc.S b/arch/powerpc/kernel/misc.S index 85cb6f34084..2d29752cbe1 100644 --- a/arch/powerpc/kernel/misc.S +++ b/arch/powerpc/kernel/misc.S @@ -31,11 +31,14 @@ _GLOBAL(reloc_offset) mflr r0 bl 1f 1: mflr r3 - LOAD_REG_IMMEDIATE(r4,1b) + PPC_LL r4,(2f-1b)(r3) subf r3,r4,r3 mtlr r0 blr + .align 3 +2: PPC_LONG 1b + /* * add_reloc_offset(x) returns x + reloc_offset(). */ @@ -43,12 +46,15 @@ _GLOBAL(add_reloc_offset) mflr r0 bl 1f 1: mflr r5 - LOAD_REG_IMMEDIATE(r4,1b) + PPC_LL r4,(2f-1b)(r5) subf r5,r4,r5 add r3,r3,r5 mtlr r0 blr + .align 3 +2: PPC_LONG 1b + _GLOBAL(kernel_execve) li r0,__NR_execve sc diff --git a/arch/powerpc/platforms/iseries/exception.S b/arch/powerpc/platforms/iseries/exception.S index 8ff330d026c..2f581521eb9 100644 --- a/arch/powerpc/platforms/iseries/exception.S +++ b/arch/powerpc/platforms/iseries/exception.S @@ -38,12 +38,13 @@ .globl system_reset_iSeries system_reset_iSeries: + bl .relative_toc mfspr r13,SPRN_SPRG3 /* Get alpaca address */ - LOAD_REG_IMMEDIATE(r23, alpaca) + LOAD_REG_ADDR(r23, alpaca) li r0,ALPACA_SIZE sub r23,r13,r23 divdu r23,r23,r0 /* r23 has cpu number */ - LOAD_REG_IMMEDIATE(r13, paca) + LOAD_REG_ADDR(r13, paca) mulli r0,r23,PACA_SIZE add r13,r13,r0 mtspr SPRN_SPRG3,r13 /* Save it away for the future */ @@ -60,14 +61,14 @@ system_reset_iSeries: mtspr SPRN_CTRLT,r4 /* Spin on __secondary_hold_spinloop until it is updated by the boot cpu. */ -/* In the UP case we'll yeild() later, and we will not access the paca anyway */ +/* In the UP case we'll yield() later, and we will not access the paca anyway */ #ifdef CONFIG_SMP 1: HMT_LOW - LOAD_REG_IMMEDIATE(r23, __secondary_hold_spinloop) + LOAD_REG_ADDR(r23, __secondary_hold_spinloop) ld r23,0(r23) sync - LOAD_REG_IMMEDIATE(r3,current_set) + LOAD_REG_ADDR(r3,current_set) sldi r28,r24,3 /* get current_set[cpu#] */ ldx r3,r3,r28 addi r1,r3,THREAD_SIZE @@ -90,7 +91,7 @@ system_reset_iSeries: lbz r23,PACAPROCSTART(r13) /* Test if this processor * should start */ sync - LOAD_REG_IMMEDIATE(r3,current_set) + LOAD_REG_ADDR(r3,current_set) sldi r28,r24,3 /* get current_set[cpu#] */ ldx r3,r3,r28 addi r1,r3,THREAD_SIZE @@ -255,8 +256,8 @@ hardware_interrupt_iSeries_masked: _INIT_STATIC(__start_initialization_iSeries) /* Clear out the BSS */ - LOAD_REG_IMMEDIATE(r11,__bss_stop) - LOAD_REG_IMMEDIATE(r8,__bss_start) + LOAD_REG_ADDR(r11,__bss_stop) + LOAD_REG_ADDR(r8,__bss_start) sub r11,r11,r8 /* bss size */ addi r11,r11,7 /* round up to an even double word */ rldicl. r11,r11,61,3 /* shift right by 3 */ @@ -267,15 +268,11 @@ _INIT_STATIC(__start_initialization_iSeries) 3: stdu r0,8(r8) bdnz 3b 4: - LOAD_REG_IMMEDIATE(r1,init_thread_union) + LOAD_REG_ADDR(r1,init_thread_union) addi r1,r1,THREAD_SIZE li r0,0 stdu r0,-STACK_FRAME_OVERHEAD(r1) - LOAD_REG_IMMEDIATE(r2,__toc_start) - addi r2,r2,0x4000 - addi r2,r2,0x4000 - bl .iSeries_early_setup bl .early_setup -- cgit v1.2.3 From 549e8152de8039506f69c677a4546e5427aa6ae7 Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Sat, 30 Aug 2008 11:43:47 +1000 Subject: powerpc: Make the 64-bit kernel as a position-independent executable This implements CONFIG_RELOCATABLE for 64-bit by making the kernel as a position-independent executable (PIE) when it is set. This involves processing the dynamic relocations in the image in the early stages of booting, even if the kernel is being run at the address it is linked at, since the linker does not necessarily fill in words in the image for which there are dynamic relocations. (In fact the linker does fill in such words for 64-bit executables, though not for 32-bit executables, so in principle we could avoid calling relocate() entirely when we're running a 64-bit kernel at the linked address.) The dynamic relocations are processed by a new function relocate(addr), where the addr parameter is the virtual address where the image will be run. In fact we call it twice; once before calling prom_init, and again when starting the main kernel. This means that reloc_offset() returns 0 in prom_init (since it has been relocated to the address it is running at), which necessitated a few adjustments. This also changes __va and __pa to use an equivalent definition that is simpler. With the relocatable kernel, PAGE_OFFSET and MEMORY_START are constants (for 64-bit) whereas PHYSICAL_START is a variable (and KERNELBASE ideally should be too, but isn't yet). With this, relocatable kernels still copy themselves down to physical address 0 and run there. Signed-off-by: Paul Mackerras --- arch/powerpc/Kconfig | 13 ++++++ arch/powerpc/Makefile | 4 +- arch/powerpc/boot/Makefile | 3 ++ arch/powerpc/boot/elf_util.c | 6 ++- arch/powerpc/include/asm/mmu-hash64.h | 2 +- arch/powerpc/include/asm/page.h | 14 ++++-- arch/powerpc/include/asm/sections.h | 6 +++ arch/powerpc/kernel/Makefile | 1 + arch/powerpc/kernel/head_64.S | 26 +++++++++-- arch/powerpc/kernel/paca.c | 3 +- arch/powerpc/kernel/prom.c | 3 ++ arch/powerpc/kernel/prom_init.c | 11 +++-- arch/powerpc/kernel/reloc_64.S | 87 +++++++++++++++++++++++++++++++++++ arch/powerpc/kernel/vmlinux.lds.S | 15 ++++++ arch/powerpc/mm/hash_utils_64.c | 2 +- arch/powerpc/platforms/powermac/smp.c | 4 +- 16 files changed, 181 insertions(+), 19 deletions(-) create mode 100644 arch/powerpc/kernel/reloc_64.S (limited to 'arch') diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig index 587da5e0990..17c988b678d 100644 --- a/arch/powerpc/Kconfig +++ b/arch/powerpc/Kconfig @@ -806,6 +806,19 @@ config PIN_TLB endmenu if PPC64 +config RELOCATABLE + bool "Build a relocatable kernel" + help + This builds a kernel image that is capable of running anywhere + in the RMA (real memory area) at any 16k-aligned base address. + The kernel is linked as a position-independent executable (PIE) + and contains dynamic relocations which are processed early + in the bootup process. + + One use is for the kexec on panic case where the recovery kernel + must live at a different physical address than the primary + kernel. + config PAGE_OFFSET hex default "0xc000000000000000" diff --git a/arch/powerpc/Makefile b/arch/powerpc/Makefile index c6be19e9cea..4df38cbb414 100644 --- a/arch/powerpc/Makefile +++ b/arch/powerpc/Makefile @@ -63,7 +63,9 @@ override CC += -m$(CONFIG_WORD_SIZE) override AR := GNUTARGET=elf$(CONFIG_WORD_SIZE)-powerpc $(AR) endif -LDFLAGS_vmlinux := -Bstatic +LDFLAGS_vmlinux-yy := -Bstatic +LDFLAGS_vmlinux-$(CONFIG_PPC64)$(CONFIG_RELOCATABLE) := -pie +LDFLAGS_vmlinux := $(LDFLAGS_vmlinux-yy) CFLAGS-$(CONFIG_PPC64) := -mminimal-toc -mtraceback=none -mcall-aixdesc CFLAGS-$(CONFIG_PPC32) := -ffixed-r2 -mmultiple diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile index 717a3bc1352..6403275553e 100644 --- a/arch/powerpc/boot/Makefile +++ b/arch/powerpc/boot/Makefile @@ -310,8 +310,11 @@ $(obj)/dtbImage.%: vmlinux $(wrapperbits) $(obj)/%.dtb $(obj)/vmlinux.strip: vmlinux $(STRIP) -s -R .comment $< -o $@ +# The iseries hypervisor won't take an ET_DYN executable, so this +# changes the type (byte 17) in the file to ET_EXEC (2). $(obj)/zImage.iseries: vmlinux $(STRIP) -s -R .comment $< -o $@ + printf "\x02" | dd of=$@ conv=notrunc bs=1 seek=17 $(obj)/uImage: vmlinux $(wrapperbits) $(call if_changed,wrap,uboot) diff --git a/arch/powerpc/boot/elf_util.c b/arch/powerpc/boot/elf_util.c index 7454aa4cc20..1567a0c0f05 100644 --- a/arch/powerpc/boot/elf_util.c +++ b/arch/powerpc/boot/elf_util.c @@ -27,7 +27,8 @@ int parse_elf64(void *hdr, struct elf_info *info) elf64->e_ident[EI_MAG3] == ELFMAG3 && elf64->e_ident[EI_CLASS] == ELFCLASS64 && elf64->e_ident[EI_DATA] == ELFDATA2MSB && - elf64->e_type == ET_EXEC && + (elf64->e_type == ET_EXEC || + elf64->e_type == ET_DYN) && elf64->e_machine == EM_PPC64)) return 0; @@ -58,7 +59,8 @@ int parse_elf32(void *hdr, struct elf_info *info) elf32->e_ident[EI_MAG3] == ELFMAG3 && elf32->e_ident[EI_CLASS] == ELFCLASS32 && elf32->e_ident[EI_DATA] == ELFDATA2MSB && - elf32->e_type == ET_EXEC && + (elf32->e_type == ET_EXEC || + elf32->e_type == ET_DYN) && elf32->e_machine == EM_PPC)) return 0; diff --git a/arch/powerpc/include/asm/mmu-hash64.h b/arch/powerpc/include/asm/mmu-hash64.h index c2df53c5ceb..5a441742ffb 100644 --- a/arch/powerpc/include/asm/mmu-hash64.h +++ b/arch/powerpc/include/asm/mmu-hash64.h @@ -437,7 +437,7 @@ typedef struct { }) #endif /* 1 */ -/* This is only valid for addresses >= KERNELBASE */ +/* This is only valid for addresses >= PAGE_OFFSET */ static inline unsigned long get_kernel_vsid(unsigned long ea, int ssize) { if (ssize == MMU_SEGSIZE_256M) diff --git a/arch/powerpc/include/asm/page.h b/arch/powerpc/include/asm/page.h index e088545cb3f..64e144505f6 100644 --- a/arch/powerpc/include/asm/page.h +++ b/arch/powerpc/include/asm/page.h @@ -71,15 +71,21 @@ #define PAGE_OFFSET ASM_CONST(CONFIG_PAGE_OFFSET) #define LOAD_OFFSET ASM_CONST((CONFIG_KERNEL_START-CONFIG_PHYSICAL_START)) -#if defined(CONFIG_RELOCATABLE) && defined(CONFIG_FLATMEM) +#if defined(CONFIG_RELOCATABLE) #ifndef __ASSEMBLY__ extern phys_addr_t memstart_addr; extern phys_addr_t kernstart_addr; #endif #define PHYSICAL_START kernstart_addr -#define MEMORY_START memstart_addr #else #define PHYSICAL_START ASM_CONST(CONFIG_PHYSICAL_START) +#endif + +#ifdef CONFIG_PPC64 +#define MEMORY_START 0UL +#elif defined(CONFIG_RELOCATABLE) +#define MEMORY_START memstart_addr +#else #define MEMORY_START (PHYSICAL_START + PAGE_OFFSET - KERNELBASE) #endif @@ -92,8 +98,8 @@ extern phys_addr_t kernstart_addr; #define pfn_to_kaddr(pfn) __va((pfn) << PAGE_SHIFT) #define virt_addr_valid(kaddr) pfn_valid(__pa(kaddr) >> PAGE_SHIFT) -#define __va(x) ((void *)((unsigned long)(x) - PHYSICAL_START + KERNELBASE)) -#define __pa(x) ((unsigned long)(x) + PHYSICAL_START - KERNELBASE) +#define __va(x) ((void *)((unsigned long)(x) + PAGE_OFFSET - MEMORY_START)) +#define __pa(x) ((unsigned long)(x) - PAGE_OFFSET + MEMORY_START) /* * Unfortunately the PLT is in the BSS in the PPC32 ELF ABI, diff --git a/arch/powerpc/include/asm/sections.h b/arch/powerpc/include/asm/sections.h index 7710e9e6660..baf318aec53 100644 --- a/arch/powerpc/include/asm/sections.h +++ b/arch/powerpc/include/asm/sections.h @@ -16,6 +16,12 @@ static inline int in_kernel_text(unsigned long addr) return 0; } +static inline int overlaps_kernel_text(unsigned long start, unsigned long end) +{ + return start < (unsigned long)__init_end && + (unsigned long)_stext < end; +} + #undef dereference_function_descriptor void *dereference_function_descriptor(void *); diff --git a/arch/powerpc/kernel/Makefile b/arch/powerpc/kernel/Makefile index 49b49c0707f..16326fd92f9 100644 --- a/arch/powerpc/kernel/Makefile +++ b/arch/powerpc/kernel/Makefile @@ -35,6 +35,7 @@ obj-$(CONFIG_PPC64) += setup_64.o sys_ppc32.o \ paca.o cpu_setup_ppc970.o \ cpu_setup_pa6t.o \ firmware.o nvram_64.o +obj64-$(CONFIG_RELOCATABLE) += reloc_64.o obj-$(CONFIG_PPC64) += vdso64/ obj-$(CONFIG_ALTIVEC) += vecemu.o vector.o obj-$(CONFIG_PPC_970_NAP) += idle_power4.o diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S index 6cdfd44d8ef..84856bee33a 100644 --- a/arch/powerpc/kernel/head_64.S +++ b/arch/powerpc/kernel/head_64.S @@ -1360,6 +1360,12 @@ _INIT_STATIC(__boot_from_prom) */ rldicr r1,r1,0,59 +#ifdef CONFIG_RELOCATABLE + /* Relocate code for where we are now */ + mr r3,r26 + bl .relocate +#endif + /* Restore parameters */ mr r3,r31 mr r4,r30 @@ -1368,11 +1374,19 @@ _INIT_STATIC(__boot_from_prom) mr r7,r27 /* Do all of the interaction with OF client interface */ + mr r8,r26 bl .prom_init /* We never return */ trap _STATIC(__after_prom_start) +#ifdef CONFIG_RELOCATABLE + /* process relocations for the final address of the kernel */ + lis r25,PAGE_OFFSET@highest /* compute virtual base of kernel */ + sldi r25,r25,32 + mr r3,r25 + bl .relocate +#endif /* * We need to run with _stext at physical address PHYSICAL_START. @@ -1381,10 +1395,9 @@ _STATIC(__after_prom_start) * * Note: This process overwrites the OF exception vectors. */ - LOAD_REG_IMMEDIATE(r3, PHYSICAL_START) /* target addr */ - cmpd r3,r26 /* In some cases the loader may */ + li r3,0 /* target addr */ + mr. r4,r26 /* In some cases the loader may */ beq 9f /* have already put us at zero */ - mr r4,r26 /* source address */ lis r5,(copy_to_here - _stext)@ha addi r5,r5,(copy_to_here - _stext)@l /* # bytes of memory to copy */ li r6,0x100 /* Start offset, the first 0x100 */ @@ -1617,6 +1630,13 @@ _INIT_STATIC(start_here_multiplatform) ori r6,r6,MSR_RI mtmsrd r6 /* RI on */ +#ifdef CONFIG_RELOCATABLE + /* Save the physical address we're running at in kernstart_addr */ + LOAD_REG_ADDR(r4, kernstart_addr) + clrldi r0,r25,2 + std r0,0(r4) +#endif + /* The following gets the stack set up with the regs */ /* pointing to the real addr of the kernel stack. This is */ /* all done to support the C function call below which sets */ diff --git a/arch/powerpc/kernel/paca.c b/arch/powerpc/kernel/paca.c index 623e8c3c57f..48a347133f4 100644 --- a/arch/powerpc/kernel/paca.c +++ b/arch/powerpc/kernel/paca.c @@ -12,6 +12,7 @@ #include #include +#include /* This symbol is provided by the linker - let it fill in the paca * field correctly */ @@ -79,7 +80,7 @@ void __init initialise_pacas(void) new_paca->lock_token = 0x8000; new_paca->paca_index = cpu; new_paca->kernel_toc = kernel_toc; - new_paca->kernelbase = KERNELBASE; + new_paca->kernelbase = (unsigned long) _stext; new_paca->kernel_msr = MSR_KERNEL; new_paca->hw_cpu_id = 0xffff; new_paca->slb_shadow_ptr = &slb_shadow[cpu]; diff --git a/arch/powerpc/kernel/prom.c b/arch/powerpc/kernel/prom.c index 09455e1c27c..3a2dc7e6586 100644 --- a/arch/powerpc/kernel/prom.c +++ b/arch/powerpc/kernel/prom.c @@ -1192,6 +1192,9 @@ void __init early_init_devtree(void *params) /* Reserve LMB regions used by kernel, initrd, dt, etc... */ lmb_reserve(PHYSICAL_START, __pa(klimit) - PHYSICAL_START); + /* If relocatable, reserve first 32k for interrupt vectors etc. */ + if (PHYSICAL_START > MEMORY_START) + lmb_reserve(MEMORY_START, 0x8000); reserve_kdump_trampoline(); reserve_crashkernel(); early_reserve_mem(); diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c index 1f898858505..7cf274a2b33 100644 --- a/arch/powerpc/kernel/prom_init.c +++ b/arch/powerpc/kernel/prom_init.c @@ -2309,13 +2309,14 @@ static void __init prom_check_initrd(unsigned long r3, unsigned long r4) unsigned long __init prom_init(unsigned long r3, unsigned long r4, unsigned long pp, - unsigned long r6, unsigned long r7) + unsigned long r6, unsigned long r7, + unsigned long kbase) { struct prom_t *_prom; unsigned long hdr; - unsigned long offset = reloc_offset(); #ifdef CONFIG_PPC32 + unsigned long offset = reloc_offset(); reloc_got2(offset); #endif @@ -2349,9 +2350,11 @@ unsigned long __init prom_init(unsigned long r3, unsigned long r4, */ RELOC(of_platform) = prom_find_machine_type(); +#ifndef CONFIG_RELOCATABLE /* Bail if this is a kdump kernel. */ if (PHYSICAL_START > 0) prom_panic("Error: You can't boot a kdump kernel from OF!\n"); +#endif /* * Check for an initrd @@ -2371,7 +2374,7 @@ unsigned long __init prom_init(unsigned long r3, unsigned long r4, * Copy the CPU hold code */ if (RELOC(of_platform) != PLATFORM_POWERMAC) - copy_and_flush(0, KERNELBASE + offset, 0x100, 0); + copy_and_flush(0, kbase, 0x100, 0); /* * Do early parsing of command line @@ -2474,7 +2477,7 @@ unsigned long __init prom_init(unsigned long r3, unsigned long r4, reloc_got2(-offset); #endif - __start(hdr, KERNELBASE + offset, 0); + __start(hdr, kbase, 0); return 0; } diff --git a/arch/powerpc/kernel/reloc_64.S b/arch/powerpc/kernel/reloc_64.S new file mode 100644 index 00000000000..b47a0e1ab00 --- /dev/null +++ b/arch/powerpc/kernel/reloc_64.S @@ -0,0 +1,87 @@ +/* + * Code to process dynamic relocations in the kernel. + * + * Copyright 2008 Paul Mackerras, IBM Corp. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include + +RELA = 7 +RELACOUNT = 0x6ffffff9 +R_PPC64_RELATIVE = 22 + +/* + * r3 = desired final address of kernel + */ +_GLOBAL(relocate) + mflr r0 + bcl 20,31,$+4 +0: mflr r12 /* r12 has runtime addr of label 0 */ + mtlr r0 + ld r11,(p_dyn - 0b)(r12) + add r11,r11,r12 /* r11 has runtime addr of .dynamic section */ + ld r9,(p_rela - 0b)(r12) + add r9,r9,r12 /* r9 has runtime addr of .rela.dyn section */ + ld r10,(p_st - 0b)(r12) + add r10,r10,r12 /* r10 has runtime addr of _stext */ + + /* + * Scan the dynamic section for the RELA and RELACOUNT entries. + */ + li r7,0 + li r8,0 +1: ld r6,0(r11) /* get tag */ + cmpdi r6,0 + beq 4f /* end of list */ + cmpdi r6,RELA + bne 2f + ld r7,8(r11) /* get RELA pointer in r7 */ + b 3f +2: addis r6,r6,(-RELACOUNT)@ha + cmpdi r6,RELACOUNT@l + bne 3f + ld r8,8(r11) /* get RELACOUNT value in r8 */ +3: addi r11,r11,16 + b 1b +4: cmpdi r7,0 /* check we have both RELA and RELACOUNT */ + cmpdi cr1,r8,0 + beq 6f + beq cr1,6f + + /* + * Work out linktime address of _stext and hence the + * relocation offset to be applied. + * cur_offset [r7] = rela.run [r9] - rela.link [r7] + * _stext.link [r10] = _stext.run [r10] - cur_offset [r7] + * final_offset [r3] = _stext.final [r3] - _stext.link [r10] + */ + subf r7,r7,r9 /* cur_offset */ + subf r10,r7,r10 + subf r3,r10,r3 /* final_offset */ + + /* + * Run through the list of relocations and process the + * R_PPC64_RELATIVE ones. + */ + mtctr r8 +5: lwz r0,12(9) /* ELF64_R_TYPE(reloc->r_info) */ + cmpwi r0,R_PPC64_RELATIVE + bne 6f + ld r6,0(r9) /* reloc->r_offset */ + ld r0,16(r9) /* reloc->r_addend */ + add r0,r0,r3 + stdx r0,r7,r6 + addi r9,r9,24 + bdnz 5b + +6: blr + +p_dyn: .llong __dynamic_start - 0b +p_rela: .llong __rela_dyn_start - 0b +p_st: .llong _stext - 0b + diff --git a/arch/powerpc/kernel/vmlinux.lds.S b/arch/powerpc/kernel/vmlinux.lds.S index 9f6c1ca1739..e6927fb2e65 100644 --- a/arch/powerpc/kernel/vmlinux.lds.S +++ b/arch/powerpc/kernel/vmlinux.lds.S @@ -187,6 +187,21 @@ SECTIONS *(.machine.desc) __machine_desc_end = . ; } + . = ALIGN(8); + .dynsym : AT(ADDR(.dynsym) - LOAD_OFFSET) { *(.dynsym) } + .dynstr : AT(ADDR(.dynstr) - LOAD_OFFSET) { *(.dynstr) } + .dynamic : AT(ADDR(.dynamic) - LOAD_OFFSET) + { + __dynamic_start = .; + *(.dynamic) + } + .hash : AT(ADDR(.hash) - LOAD_OFFSET) { *(.hash) } + .interp : AT(ADDR(.interp) - LOAD_OFFSET) { *(.interp) } + .rela.dyn : AT(ADDR(.rela.dyn) - LOAD_OFFSET) + { + __rela_dyn_start = .; + *(.rela*) + } /* freed after init ends here */ . = ALIGN(PAGE_SIZE); diff --git a/arch/powerpc/mm/hash_utils_64.c b/arch/powerpc/mm/hash_utils_64.c index d666f71f1f3..09db4efe192 100644 --- a/arch/powerpc/mm/hash_utils_64.c +++ b/arch/powerpc/mm/hash_utils_64.c @@ -194,7 +194,7 @@ int htab_bolt_mapping(unsigned long vstart, unsigned long vend, unsigned long tprot = prot; /* Make kernel text executable */ - if (in_kernel_text(vaddr)) + if (overlaps_kernel_text(vaddr, vaddr + step)) tprot &= ~HPTE_R_N; hash = hpt_hash(va, shift, ssize); diff --git a/arch/powerpc/platforms/powermac/smp.c b/arch/powerpc/platforms/powermac/smp.c index 4ae3d00e0bd..40f72c2a469 100644 --- a/arch/powerpc/platforms/powermac/smp.c +++ b/arch/powerpc/platforms/powermac/smp.c @@ -787,7 +787,7 @@ static void __devinit smp_core99_kick_cpu(int nr) { unsigned int save_vector; unsigned long target, flags; - unsigned int *vector = (unsigned int *)(KERNELBASE+0x100); + unsigned int *vector = (unsigned int *)(PAGE_OFFSET+0x100); if (nr < 0 || nr > 3) return; @@ -801,7 +801,7 @@ static void __devinit smp_core99_kick_cpu(int nr) save_vector = *vector; /* Setup fake reset vector that does - * b __secondary_start_pmac_0 + nr*8 - KERNELBASE + * b __secondary_start_pmac_0 + nr*8 */ target = (unsigned long) __secondary_start_pmac_0 + nr * 8; patch_branch(vector, target, BRANCH_SET_LINK); -- cgit v1.2.3 From d6c93adbeb98c56e19f7df37633566b39fbcd4c9 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Mon, 1 Sep 2008 11:23:30 +1000 Subject: powerpc: Use sys_pause for 32-bit pause entry point sys32_pause is a useless copy of the generic sys_pause. Signed-off-by: Christoph Hellwig Acked-by: Stephen Rothwell Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/systbl.h | 2 +- arch/powerpc/kernel/sys_ppc32.c | 8 -------- 2 files changed, 1 insertion(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/systbl.h b/arch/powerpc/include/asm/systbl.h index f6cc7a43b4f..803def23665 100644 --- a/arch/powerpc/include/asm/systbl.h +++ b/arch/powerpc/include/asm/systbl.h @@ -32,7 +32,7 @@ COMPAT_SYS_SPU(stime) COMPAT_SYS(ptrace) SYSCALL_SPU(alarm) OLDSYS(fstat) -COMPAT_SYS(pause) +SYSCALL(pause) COMPAT_SYS(utime) SYSCALL(ni_syscall) SYSCALL(ni_syscall) diff --git a/arch/powerpc/kernel/sys_ppc32.c b/arch/powerpc/kernel/sys_ppc32.c index d98634c7606..ff7de7b0797 100644 --- a/arch/powerpc/kernel/sys_ppc32.c +++ b/arch/powerpc/kernel/sys_ppc32.c @@ -107,14 +107,6 @@ asmlinkage long compat_sys_sysfs(u32 option, u32 arg1, u32 arg2) return sys_sysfs((int)option, arg1, arg2); } -asmlinkage long compat_sys_pause(void) -{ - current->state = TASK_INTERRUPTIBLE; - schedule(); - - return -ERESTARTNOHAND; -} - static inline long get_ts32(struct timespec *o, struct compat_timeval __user *i) { long usec; -- cgit v1.2.3 From ce400c0102d8e1367266115ce6bc22333e5e3da6 Mon Sep 17 00:00:00 2001 From: Thiemo Seufer Date: Tue, 2 Sep 2008 00:23:02 +1000 Subject: powerpc: Enforce a non-spe kernel build even on broken compilers Those two are required on my fresh gcc 4.3.1. Signed-off-by: Thiemo Seufer Signed-off-by: Sebastian Siewior Signed-off-by: Paul Mackerras --- arch/powerpc/Makefile | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/Makefile b/arch/powerpc/Makefile index 4df38cbb414..24dd1a37f8f 100644 --- a/arch/powerpc/Makefile +++ b/arch/powerpc/Makefile @@ -104,7 +104,10 @@ endif KBUILD_CFLAGS += $(call cc-option,-mno-altivec) # No SPE instruction when building kernel +# (We use all available options to help semi-broken compilers) KBUILD_CFLAGS += $(call cc-option,-mno-spe) +KBUILD_CFLAGS += $(call cc-option,-mspe=no) +KBUILD_CFLAGS += $(call cc-option,-mabi=no-spe) # Enable unit-at-a-time mode when possible. It shrinks the # kernel considerably. -- cgit v1.2.3 From aaf4a9b0f78786e6915077cbbb1d6f4fb6a8ee0b Mon Sep 17 00:00:00 2001 From: Becky Bruce Date: Thu, 4 Sep 2008 01:37:53 +1000 Subject: powerpc: Rename PTE_SIZE to HPTE_SIZE It's the size of the hardware PTE; make that clear in the name. Signed-off-by: Becky Bruce Acked-by: Benjamin Herrenschmidt Signed-off-by: Paul Mackerras --- arch/powerpc/mm/hash_low_32.S | 36 ++++++++++++++++++------------------ 1 file changed, 18 insertions(+), 18 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/mm/hash_low_32.S b/arch/powerpc/mm/hash_low_32.S index b9ba7d93080..c41d658176a 100644 --- a/arch/powerpc/mm/hash_low_32.S +++ b/arch/powerpc/mm/hash_low_32.S @@ -285,7 +285,7 @@ Hash_bits = 12 /* e.g. 256kB hash table */ Hash_msk = (((1 << Hash_bits) - 1) * 64) /* defines for the PTE format for 32-bit PPCs */ -#define PTE_SIZE 8 +#define HPTE_SIZE 8 #define PTEG_SIZE 64 #define LG_PTEG_SIZE 6 #define LDPTEu lwzu @@ -342,8 +342,8 @@ _GLOBAL(hash_page_patch_A) /* Search the primary PTEG for a PTE whose 1st (d)word matches r5 */ mtctr r0 - addi r4,r3,-PTE_SIZE -1: LDPTEu r6,PTE_SIZE(r4) /* get next PTE */ + addi r4,r3,-HPTE_SIZE +1: LDPTEu r6,HPTE_SIZE(r4) /* get next PTE */ CMPPTE 0,r6,r5 bdnzf 2,1b /* loop while ctr != 0 && !cr0.eq */ beq+ found_slot @@ -353,9 +353,9 @@ _GLOBAL(hash_page_patch_A) _GLOBAL(hash_page_patch_B) xoris r4,r3,Hash_msk>>16 /* compute secondary hash */ xori r4,r4,(-PTEG_SIZE & 0xffff) - addi r4,r4,-PTE_SIZE + addi r4,r4,-HPTE_SIZE mtctr r0 -2: LDPTEu r6,PTE_SIZE(r4) +2: LDPTEu r6,HPTE_SIZE(r4) CMPPTE 0,r6,r5 bdnzf 2,2b beq+ found_slot @@ -363,8 +363,8 @@ _GLOBAL(hash_page_patch_B) /* Search the primary PTEG for an empty slot */ 10: mtctr r0 - addi r4,r3,-PTE_SIZE /* search primary PTEG */ -1: LDPTEu r6,PTE_SIZE(r4) /* get next PTE */ + addi r4,r3,-HPTE_SIZE /* search primary PTEG */ +1: LDPTEu r6,HPTE_SIZE(r4) /* get next PTE */ TST_V(r6) /* test valid bit */ bdnzf 2,1b /* loop while ctr != 0 && !cr0.eq */ beq+ found_empty @@ -380,9 +380,9 @@ _GLOBAL(hash_page_patch_B) _GLOBAL(hash_page_patch_C) xoris r4,r3,Hash_msk>>16 /* compute secondary hash */ xori r4,r4,(-PTEG_SIZE & 0xffff) - addi r4,r4,-PTE_SIZE + addi r4,r4,-HPTE_SIZE mtctr r0 -2: LDPTEu r6,PTE_SIZE(r4) +2: LDPTEu r6,HPTE_SIZE(r4) TST_V(r6) bdnzf 2,2b beq+ found_empty @@ -409,11 +409,11 @@ _GLOBAL(hash_page_patch_C) 1: addis r4,r7,next_slot@ha /* get next evict slot */ lwz r6,next_slot@l(r4) - addi r6,r6,PTE_SIZE /* search for candidate */ - andi. r6,r6,7*PTE_SIZE + addi r6,r6,HPTE_SIZE /* search for candidate */ + andi. r6,r6,7*HPTE_SIZE stw r6,next_slot@l(r4) add r4,r3,r6 - LDPTE r0,PTE_SIZE/2(r4) /* get PTE second word */ + LDPTE r0,HPTE_SIZE/2(r4) /* get PTE second word */ clrrwi r0,r0,12 lis r6,etext@h ori r6,r6,etext@l /* get etext */ @@ -426,7 +426,7 @@ _GLOBAL(hash_page_patch_C) found_empty: STPTE r5,0(r4) found_slot: - STPTE r8,PTE_SIZE/2(r4) + STPTE r8,HPTE_SIZE/2(r4) #else /* CONFIG_SMP */ /* @@ -452,7 +452,7 @@ found_slot: STPTE r5,0(r4) sync TLBSYNC - STPTE r8,PTE_SIZE/2(r4) /* put in correct RPN, WIMG, PP bits */ + STPTE r8,HPTE_SIZE/2(r4) /* put in correct RPN, WIMG, PP bits */ sync SET_V(r5) STPTE r5,0(r4) /* finally set V bit in PTE */ @@ -562,8 +562,8 @@ _GLOBAL(flush_hash_patch_A) /* Search the primary PTEG for a PTE whose 1st (d)word matches r5 */ li r0,8 /* PTEs/group */ mtctr r0 - addi r12,r8,-PTE_SIZE -1: LDPTEu r0,PTE_SIZE(r12) /* get next PTE */ + addi r12,r8,-HPTE_SIZE +1: LDPTEu r0,HPTE_SIZE(r12) /* get next PTE */ CMPPTE 0,r0,r11 bdnzf 2,1b /* loop while ctr != 0 && !cr0.eq */ beq+ 3f @@ -574,9 +574,9 @@ _GLOBAL(flush_hash_patch_A) _GLOBAL(flush_hash_patch_B) xoris r12,r8,Hash_msk>>16 /* compute secondary hash */ xori r12,r12,(-PTEG_SIZE & 0xffff) - addi r12,r12,-PTE_SIZE + addi r12,r12,-HPTE_SIZE mtctr r0 -2: LDPTEu r0,PTE_SIZE(r12) +2: LDPTEu r0,HPTE_SIZE(r12) CMPPTE 0,r0,r11 bdnzf 2,2b xori r11,r11,PTE_H /* clear H again */ -- cgit v1.2.3 From 967e012ef306e99cfddcd7423f37414e6b568361 Mon Sep 17 00:00:00 2001 From: Sebastien Dugue Date: Thu, 4 Sep 2008 22:37:07 +1000 Subject: powerpc: Separate the irq radix tree insertion and lookup irq_radix_revmap() currently serves 2 purposes, irq mapping lookup and insertion which happen in interrupt and process context respectively. Separate the function into its 2 components, one for lookup only and one for insertion only. Fix the only user of the revmap tree (XICS) to use the new functions. Also, move the insertion into the radix tree of those irqs that were requested before it was initialized at said tree initialization. Mutual exclusion between the tree initialization and readers/writers is handled via a state variable (revmap_trees_allocated) set to 1 when the tree has been initialized and set to 2 after the already requested irqs have been inserted in the tree by the init path. This state is checked before any reader or writer access just like we used to check for tree.gfp_mask != 0 before. Finally, now that we're not any longer inserting nodes into the radix-tree in interrupt context, turn the GFP_ATOMIC allocations into GFP_KERNEL ones. Signed-off-by: Sebastien Dugue Cc: Benjamin Herrenschmidt Cc: Michael Ellerman Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/irq.h | 18 +++++-- arch/powerpc/kernel/irq.c | 97 +++++++++++++++++++++++++++-------- arch/powerpc/platforms/pseries/xics.c | 11 ++-- 3 files changed, 95 insertions(+), 31 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/irq.h b/arch/powerpc/include/asm/irq.h index a372f76836c..0a5137676e1 100644 --- a/arch/powerpc/include/asm/irq.h +++ b/arch/powerpc/include/asm/irq.h @@ -236,15 +236,27 @@ extern unsigned int irq_find_mapping(struct irq_host *host, extern unsigned int irq_create_direct_mapping(struct irq_host *host); /** - * irq_radix_revmap - Find a linux virq from a hw irq number. + * irq_radix_revmap_insert - Insert a hw irq to linux virq number mapping. + * @host: host owning this hardware interrupt + * @virq: linux irq number + * @hwirq: hardware irq number in that host space + * + * This is for use by irq controllers that use a radix tree reverse + * mapping for fast lookup. + */ +extern void irq_radix_revmap_insert(struct irq_host *host, unsigned int virq, + irq_hw_number_t hwirq); + +/** + * irq_radix_revmap_lookup - Find a linux virq from a hw irq number. * @host: host owning this hardware interrupt * @hwirq: hardware irq number in that host space * * This is a fast path, for use by irq controller code that uses radix tree * revmaps */ -extern unsigned int irq_radix_revmap(struct irq_host *host, - irq_hw_number_t hwirq); +extern unsigned int irq_radix_revmap_lookup(struct irq_host *host, + irq_hw_number_t hwirq); /** * irq_linear_revmap - Find a linux virq from a hw irq number. diff --git a/arch/powerpc/kernel/irq.c b/arch/powerpc/kernel/irq.c index d972decf032..2656924415d 100644 --- a/arch/powerpc/kernel/irq.c +++ b/arch/powerpc/kernel/irq.c @@ -441,6 +441,7 @@ static LIST_HEAD(irq_hosts); static DEFINE_SPINLOCK(irq_big_lock); static DEFINE_PER_CPU(unsigned int, irq_radix_reader); static unsigned int irq_radix_writer; +static unsigned int revmap_trees_allocated; struct irq_map_entry irq_map[NR_IRQS]; static unsigned int irq_virq_count = NR_IRQS; static struct irq_host *irq_default_host; @@ -821,8 +822,12 @@ void irq_dispose_mapping(unsigned int virq) host->revmap_data.linear.revmap[hwirq] = NO_IRQ; break; case IRQ_HOST_MAP_TREE: - /* Check if radix tree allocated yet */ - if (host->revmap_data.tree.gfp_mask == 0) + /* + * Check if radix tree allocated yet, if not then nothing to + * remove. + */ + smp_rmb(); + if (revmap_trees_allocated < 1) break; irq_radix_wrlock(&flags); radix_tree_delete(&host->revmap_data.tree, hwirq); @@ -875,43 +880,62 @@ unsigned int irq_find_mapping(struct irq_host *host, EXPORT_SYMBOL_GPL(irq_find_mapping); -unsigned int irq_radix_revmap(struct irq_host *host, - irq_hw_number_t hwirq) +unsigned int irq_radix_revmap_lookup(struct irq_host *host, + irq_hw_number_t hwirq) { - struct radix_tree_root *tree; struct irq_map_entry *ptr; unsigned int virq; unsigned long flags; WARN_ON(host->revmap_type != IRQ_HOST_MAP_TREE); - /* Check if the radix tree exist yet. We test the value of - * the gfp_mask for that. Sneaky but saves another int in the - * structure. If not, we fallback to slow mode + /* + * Check if the radix tree exists and has bee initialized. + * If not, we fallback to slow mode */ - tree = &host->revmap_data.tree; - if (tree->gfp_mask == 0) + if (revmap_trees_allocated < 2) return irq_find_mapping(host, hwirq); /* Now try to resolve */ irq_radix_rdlock(&flags); - ptr = radix_tree_lookup(tree, hwirq); + ptr = radix_tree_lookup(&host->revmap_data.tree, hwirq); irq_radix_rdunlock(flags); - /* Found it, return */ - if (ptr) { + /* + * If found in radix tree, then fine. + * Else fallback to linear lookup - this should not happen in practice + * as it means that we failed to insert the node in the radix tree. + */ + if (ptr) virq = ptr - irq_map; - return virq; - } + else + virq = irq_find_mapping(host, hwirq); + + return virq; +} + +void irq_radix_revmap_insert(struct irq_host *host, unsigned int virq, + irq_hw_number_t hwirq) +{ + unsigned long flags; + + WARN_ON(host->revmap_type != IRQ_HOST_MAP_TREE); + + /* + * Check if the radix tree exists yet. + * If not, then the irq will be inserted into the tree when it gets + * initialized. + */ + smp_rmb(); + if (revmap_trees_allocated < 1) + return; - /* If not there, try to insert it */ - virq = irq_find_mapping(host, hwirq); if (virq != NO_IRQ) { irq_radix_wrlock(&flags); - radix_tree_insert(tree, hwirq, &irq_map[virq]); + radix_tree_insert(&host->revmap_data.tree, hwirq, + &irq_map[virq]); irq_radix_wrunlock(flags); } - return virq; } unsigned int irq_linear_revmap(struct irq_host *host, @@ -1021,14 +1045,45 @@ static int irq_late_init(void) { struct irq_host *h; unsigned long flags; + unsigned int i; - irq_radix_wrlock(&flags); + /* + * No mutual exclusion with respect to accessors of the tree is needed + * here as the synchronization is done via the state variable + * revmap_trees_allocated. + */ list_for_each_entry(h, &irq_hosts, link) { if (h->revmap_type == IRQ_HOST_MAP_TREE) - INIT_RADIX_TREE(&h->revmap_data.tree, GFP_ATOMIC); + INIT_RADIX_TREE(&h->revmap_data.tree, GFP_KERNEL); + } + + /* + * Make sure the radix trees inits are visible before setting + * the flag + */ + smp_wmb(); + revmap_trees_allocated = 1; + + /* + * Insert the reverse mapping for those interrupts already present + * in irq_map[]. + */ + irq_radix_wrlock(&flags); + for (i = 0; i < irq_virq_count; i++) { + if (irq_map[i].host && + (irq_map[i].host->revmap_type == IRQ_HOST_MAP_TREE)) + radix_tree_insert(&irq_map[i].host->revmap_data.tree, + irq_map[i].hwirq, &irq_map[i]); } irq_radix_wrunlock(flags); + /* + * Make sure the radix trees insertions are visible before setting + * the flag + */ + smp_wmb(); + revmap_trees_allocated = 2; + return 0; } arch_initcall(irq_late_init); diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 0fc830f576f..6b1a005cc0c 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -310,12 +310,6 @@ static void xics_mask_irq(unsigned int virq) static unsigned int xics_startup(unsigned int virq) { - unsigned int irq; - - /* force a reverse mapping of the interrupt so it gets in the cache */ - irq = (unsigned int)irq_map[virq].hwirq; - irq_radix_revmap(xics_host, irq); - /* unmask it */ xics_unmask_irq(virq); return 0; @@ -346,7 +340,7 @@ static inline unsigned int xics_remap_irq(unsigned int vec) if (vec == XICS_IRQ_SPURIOUS) return NO_IRQ; - irq = irq_radix_revmap(xics_host, vec); + irq = irq_radix_revmap_lookup(xics_host, vec); if (likely(irq != NO_IRQ)) return irq; @@ -530,6 +524,9 @@ static int xics_host_map(struct irq_host *h, unsigned int virq, { pr_debug("xics: map virq %d, hwirq 0x%lx\n", virq, hw); + /* Insert the interrupt mapping into the radix tree for fast lookup */ + irq_radix_revmap_insert(xics_host, virq, hw); + get_irq_desc(virq)->status |= IRQ_LEVEL; set_irq_chip_and_handler(virq, xics_irq_chip, handle_fasteoi_irq); return 0; -- cgit v1.2.3 From 150c6c8fecf6daaf68c2987ba2b6b259baefdff2 Mon Sep 17 00:00:00 2001 From: Sebastien Dugue Date: Thu, 4 Sep 2008 22:37:08 +1000 Subject: powerpc: Make the irq reverse mapping radix tree lockless The radix trees used by interrupt controllers for their irq reverse mapping (currently only the XICS found on pSeries) have a complex locking scheme dating back to before the advent of the lockless radix tree. This takes advantage of the lockless radix tree and of the fact that the items of the tree are pointers to a static array (irq_map) elements which can never go under us to simplify the locking. Concurrency between readers and writers is handled by the intrinsic properties of the lockless radix tree. Concurrency between writers is handled with a global mutex. Signed-off-by: Sebastien Dugue Cc: Benjamin Herrenschmidt Cc: Michael Ellerman Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/irq.c | 76 +++++++---------------------------------------- 1 file changed, 11 insertions(+), 65 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/irq.c b/arch/powerpc/kernel/irq.c index 2656924415d..ac222d0ab12 100644 --- a/arch/powerpc/kernel/irq.c +++ b/arch/powerpc/kernel/irq.c @@ -439,9 +439,8 @@ void do_softirq(void) static LIST_HEAD(irq_hosts); static DEFINE_SPINLOCK(irq_big_lock); -static DEFINE_PER_CPU(unsigned int, irq_radix_reader); -static unsigned int irq_radix_writer; static unsigned int revmap_trees_allocated; +static DEFINE_MUTEX(revmap_trees_mutex); struct irq_map_entry irq_map[NR_IRQS]; static unsigned int irq_virq_count = NR_IRQS; static struct irq_host *irq_default_host; @@ -584,57 +583,6 @@ void irq_set_virq_count(unsigned int count) irq_virq_count = count; } -/* radix tree not lockless safe ! we use a brlock-type mecanism - * for now, until we can use a lockless radix tree - */ -static void irq_radix_wrlock(unsigned long *flags) -{ - unsigned int cpu, ok; - - spin_lock_irqsave(&irq_big_lock, *flags); - irq_radix_writer = 1; - smp_mb(); - do { - barrier(); - ok = 1; - for_each_possible_cpu(cpu) { - if (per_cpu(irq_radix_reader, cpu)) { - ok = 0; - break; - } - } - if (!ok) - cpu_relax(); - } while(!ok); -} - -static void irq_radix_wrunlock(unsigned long flags) -{ - smp_wmb(); - irq_radix_writer = 0; - spin_unlock_irqrestore(&irq_big_lock, flags); -} - -static void irq_radix_rdlock(unsigned long *flags) -{ - local_irq_save(*flags); - __get_cpu_var(irq_radix_reader) = 1; - smp_mb(); - if (likely(irq_radix_writer == 0)) - return; - __get_cpu_var(irq_radix_reader) = 0; - smp_wmb(); - spin_lock(&irq_big_lock); - __get_cpu_var(irq_radix_reader) = 1; - spin_unlock(&irq_big_lock); -} - -static void irq_radix_rdunlock(unsigned long flags) -{ - __get_cpu_var(irq_radix_reader) = 0; - local_irq_restore(flags); -} - static int irq_setup_virq(struct irq_host *host, unsigned int virq, irq_hw_number_t hwirq) { @@ -789,7 +737,6 @@ void irq_dispose_mapping(unsigned int virq) { struct irq_host *host; irq_hw_number_t hwirq; - unsigned long flags; if (virq == NO_IRQ) return; @@ -829,9 +776,9 @@ void irq_dispose_mapping(unsigned int virq) smp_rmb(); if (revmap_trees_allocated < 1) break; - irq_radix_wrlock(&flags); + mutex_lock(&revmap_trees_mutex); radix_tree_delete(&host->revmap_data.tree, hwirq); - irq_radix_wrunlock(flags); + mutex_unlock(&revmap_trees_mutex); break; } @@ -885,7 +832,6 @@ unsigned int irq_radix_revmap_lookup(struct irq_host *host, { struct irq_map_entry *ptr; unsigned int virq; - unsigned long flags; WARN_ON(host->revmap_type != IRQ_HOST_MAP_TREE); @@ -897,9 +843,11 @@ unsigned int irq_radix_revmap_lookup(struct irq_host *host, return irq_find_mapping(host, hwirq); /* Now try to resolve */ - irq_radix_rdlock(&flags); + /* + * No rcu_read_lock(ing) needed, the ptr returned can't go under us + * as it's referencing an entry in the static irq_map table. + */ ptr = radix_tree_lookup(&host->revmap_data.tree, hwirq); - irq_radix_rdunlock(flags); /* * If found in radix tree, then fine. @@ -917,7 +865,6 @@ unsigned int irq_radix_revmap_lookup(struct irq_host *host, void irq_radix_revmap_insert(struct irq_host *host, unsigned int virq, irq_hw_number_t hwirq) { - unsigned long flags; WARN_ON(host->revmap_type != IRQ_HOST_MAP_TREE); @@ -931,10 +878,10 @@ void irq_radix_revmap_insert(struct irq_host *host, unsigned int virq, return; if (virq != NO_IRQ) { - irq_radix_wrlock(&flags); + mutex_lock(&revmap_trees_mutex); radix_tree_insert(&host->revmap_data.tree, hwirq, &irq_map[virq]); - irq_radix_wrunlock(flags); + mutex_unlock(&revmap_trees_mutex); } } @@ -1044,7 +991,6 @@ void irq_early_init(void) static int irq_late_init(void) { struct irq_host *h; - unsigned long flags; unsigned int i; /* @@ -1068,14 +1014,14 @@ static int irq_late_init(void) * Insert the reverse mapping for those interrupts already present * in irq_map[]. */ - irq_radix_wrlock(&flags); + mutex_lock(&revmap_trees_mutex); for (i = 0; i < irq_virq_count; i++) { if (irq_map[i].host && (irq_map[i].host->revmap_type == IRQ_HOST_MAP_TREE)) radix_tree_insert(&irq_map[i].host->revmap_data.tree, irq_map[i].hwirq, &irq_map[i]); } - irq_radix_wrunlock(flags); + mutex_unlock(&revmap_trees_mutex); /* * Make sure the radix trees insertions are visible before setting -- cgit v1.2.3 From 0b26425ce101a7c1b1ad4ec353d4e860223d9fc4 Mon Sep 17 00:00:00 2001 From: David Gibson Date: Fri, 5 Sep 2008 11:49:54 +1000 Subject: powerpc: Clean up hugepage pagetable allocation for powerpc with 16G pages There is a small bug in the handling of 16G hugepages recently added to the kernel. This doesn't cause a crash or other user-visible problems, but it does mean that more levels of pagetable are allocated than makes sense for 16G pages. The hugepage pagetables for the 16G pages are allocated much lower in the pagetable tree than they should be, with the intervening levels allocated with full pmd and pud pages which will only ever have one entry filled in. This corrects this problem, at the same time cleaning up the handling of which level 64k versus 16M hugepage pagetables are allocated at. The new way of formatting the tests should be more robust against changes in pagetable structure, or any newly added hugepage sizes. Signed-off-by: David Gibson Signed-off-by: Paul Mackerras --- arch/powerpc/mm/hugetlbpage.c | 59 ++++++++++++++++++++++++------------------- 1 file changed, 33 insertions(+), 26 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/mm/hugetlbpage.c b/arch/powerpc/mm/hugetlbpage.c index f1c2d55b437..a117024ab8c 100644 --- a/arch/powerpc/mm/hugetlbpage.c +++ b/arch/powerpc/mm/hugetlbpage.c @@ -128,29 +128,37 @@ static int __hugepte_alloc(struct mm_struct *mm, hugepd_t *hpdp, return 0; } -/* Base page size affects how we walk hugetlb page tables */ -#ifdef CONFIG_PPC_64K_PAGES -#define hpmd_offset(pud, addr, h) pmd_offset(pud, addr) -#define hpmd_alloc(mm, pud, addr, h) pmd_alloc(mm, pud, addr) -#else -static inline -pmd_t *hpmd_offset(pud_t *pud, unsigned long addr, struct hstate *hstate) + +static pud_t *hpud_offset(pgd_t *pgd, unsigned long addr, struct hstate *hstate) +{ + if (huge_page_shift(hstate) < PUD_SHIFT) + return pud_offset(pgd, addr); + else + return (pud_t *) pgd; +} +static pud_t *hpud_alloc(struct mm_struct *mm, pgd_t *pgd, unsigned long addr, + struct hstate *hstate) { - if (huge_page_shift(hstate) == PAGE_SHIFT_64K) + if (huge_page_shift(hstate) < PUD_SHIFT) + return pud_alloc(mm, pgd, addr); + else + return (pud_t *) pgd; +} +static pmd_t *hpmd_offset(pud_t *pud, unsigned long addr, struct hstate *hstate) +{ + if (huge_page_shift(hstate) < PMD_SHIFT) return pmd_offset(pud, addr); else return (pmd_t *) pud; } -static inline -pmd_t *hpmd_alloc(struct mm_struct *mm, pud_t *pud, unsigned long addr, - struct hstate *hstate) +static pmd_t *hpmd_alloc(struct mm_struct *mm, pud_t *pud, unsigned long addr, + struct hstate *hstate) { - if (huge_page_shift(hstate) == PAGE_SHIFT_64K) + if (huge_page_shift(hstate) < PMD_SHIFT) return pmd_alloc(mm, pud, addr); else return (pmd_t *) pud; } -#endif /* Build list of addresses of gigantic pages. This function is used in early * boot before the buddy or bootmem allocator is setup. @@ -204,7 +212,7 @@ pte_t *huge_pte_offset(struct mm_struct *mm, unsigned long addr) pg = pgd_offset(mm, addr); if (!pgd_none(*pg)) { - pu = pud_offset(pg, addr); + pu = hpud_offset(pg, addr, hstate); if (!pud_none(*pu)) { pm = hpmd_offset(pu, addr, hstate); if (!pmd_none(*pm)) @@ -233,7 +241,7 @@ pte_t *huge_pte_alloc(struct mm_struct *mm, addr &= hstate->mask; pg = pgd_offset(mm, addr); - pu = pud_alloc(mm, pg, addr); + pu = hpud_alloc(mm, pg, addr, hstate); if (pu) { pm = hpmd_alloc(mm, pu, addr, hstate); @@ -316,13 +324,7 @@ static void hugetlb_free_pud_range(struct mmu_gather *tlb, pgd_t *pgd, pud = pud_offset(pgd, addr); do { next = pud_addr_end(addr, end); -#ifdef CONFIG_PPC_64K_PAGES - if (pud_none_or_clear_bad(pud)) - continue; - hugetlb_free_pmd_range(tlb, pud, addr, next, floor, ceiling, - psize); -#else - if (shift == PAGE_SHIFT_64K) { + if (shift < PMD_SHIFT) { if (pud_none_or_clear_bad(pud)) continue; hugetlb_free_pmd_range(tlb, pud, addr, next, floor, @@ -332,7 +334,6 @@ static void hugetlb_free_pud_range(struct mmu_gather *tlb, pgd_t *pgd, continue; free_hugepte_range(tlb, (hugepd_t *)pud, psize); } -#endif } while (pud++, addr = next, addr != end); start &= PGDIR_MASK; @@ -422,9 +423,15 @@ void hugetlb_free_pgd_range(struct mmu_gather *tlb, psize = get_slice_psize(tlb->mm, addr); BUG_ON(!mmu_huge_psizes[psize]); next = pgd_addr_end(addr, end); - if (pgd_none_or_clear_bad(pgd)) - continue; - hugetlb_free_pud_range(tlb, pgd, addr, next, floor, ceiling); + if (mmu_psize_to_shift(psize) < PUD_SHIFT) { + if (pgd_none_or_clear_bad(pgd)) + continue; + hugetlb_free_pud_range(tlb, pgd, addr, next, floor, ceiling); + } else { + if (pgd_none(*pgd)) + continue; + free_hugepte_range(tlb, (hugepd_t *)pgd, psize); + } } while (pgd++, addr = next, addr != end); } -- cgit v1.2.3 From a501d8f30e4fcca563e4ee462be00f96e51181d5 Mon Sep 17 00:00:00 2001 From: Martin Langer Date: Sun, 7 Sep 2008 17:51:32 +1000 Subject: powerpc: Fix major revision number for Freescale cores Some 74xx cores by Freescale are using the configuration field instead of the major revision field for their revision number. This corrects the wrong behaviour for those ppc cores including my one. There is a reference document at Freecale. It describes the PVR register. This is based on that pdf. You can find the document at: http://www.freescale.com/files/archives/doc/support_info/PPCPVR.pdf Signed-off-by: Martin Langer Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/setup-common.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/setup-common.c b/arch/powerpc/kernel/setup-common.c index 9cc5a52711e..5ec56ff03e8 100644 --- a/arch/powerpc/kernel/setup-common.c +++ b/arch/powerpc/kernel/setup-common.c @@ -254,8 +254,21 @@ static int show_cpuinfo(struct seq_file *m, void *v) /* If we are a Freescale core do a simple check so * we dont have to keep adding cases in the future */ if (PVR_VER(pvr) & 0x8000) { - maj = PVR_MAJ(pvr); - min = PVR_MIN(pvr); + switch (PVR_VER(pvr)) { + case 0x8000: /* 7441/7450/7451, Voyager */ + case 0x8001: /* 7445/7455, Apollo 6 */ + case 0x8002: /* 7447/7457, Apollo 7 */ + case 0x8003: /* 7447A, Apollo 7 PM */ + case 0x8004: /* 7448, Apollo 8 */ + case 0x800c: /* 7410, Nitro */ + maj = ((pvr >> 8) & 0xF); + min = PVR_MIN(pvr); + break; + default: /* e500/book-e */ + maj = PVR_MAJ(pvr); + min = PVR_MIN(pvr); + break; + } } else { switch (PVR_VER(pvr)) { case 0x0020: /* 403 family */ -- cgit v1.2.3 From e14d4af0c87af0be7f2d0e204e1922cf4fa3c19e Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Sat, 14 Jun 2008 21:02:04 +0200 Subject: powerpc: Add support for the MPC852 based mgsuvd board from keymile. Supported SMC1 (serial console), SCC3 Ethernet (10Mbps hdx). Signed-off-by: Heiko Schocher Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mgsuvd.dts | 163 +++++++ arch/powerpc/configs/mgsuvd_defconfig | 872 ++++++++++++++++++++++++++++++++++ arch/powerpc/platforms/8xx/Kconfig | 6 + arch/powerpc/platforms/8xx/Makefile | 1 + arch/powerpc/platforms/8xx/mgsuvd.c | 92 ++++ 5 files changed, 1134 insertions(+) create mode 100644 arch/powerpc/boot/dts/mgsuvd.dts create mode 100644 arch/powerpc/configs/mgsuvd_defconfig create mode 100644 arch/powerpc/platforms/8xx/mgsuvd.c (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mgsuvd.dts b/arch/powerpc/boot/dts/mgsuvd.dts new file mode 100644 index 00000000000..e4fc53ab42b --- /dev/null +++ b/arch/powerpc/boot/dts/mgsuvd.dts @@ -0,0 +1,163 @@ +/* + * MGSUVD Device Tree Source + * + * Copyright 2008 DENX Software Engineering GmbH + * Heiko Schocher + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; +/ { + model = "MGSUVD"; + compatible = "keymile,mgsuvd"; + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,852@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <16>; + i-cache-line-size = <16>; + d-cache-size = <8192>; + i-cache-size = <8192>; + timebase-frequency = <0>; /* Filled in by u-boot */ + bus-frequency = <0>; /* Filled in by u-boot */ + clock-frequency = <0>; /* Filled in by u-boot */ + interrupts = <15 2>; /* decrementer interrupt */ + interrupt-parent = <&PIC>; + }; + }; + + memory { + device_type = "memory"; + reg = <00000000 0x4000000>; /* Filled in by u-boot */ + }; + + localbus@fff00100 { + compatible = "fsl,mpc852-localbus", "fsl,pq1-localbus", "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0xfff00100 0x40>; + + ranges = <0 0 0xf0000000 0x01000000>; /* Filled in by u-boot */ + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0 0x1000000>; + #address-cells = <1>; + #size-cells = <1>; + bank-width = <1>; + device-width = <1>; + partition@0 { + label = "u-boot"; + reg = <0 0x80000>; + }; + partition@80000 { + label = "env"; + reg = <0x80000 0x20000>; + }; + partition@a0000 { + label = "kernel"; + reg = <0xa0000 0x1e0000>; + }; + partition@280000 { + label = "dtb"; + reg = <0x280000 0x20000>; + }; + partition@2a0000 { + label = "root"; + reg = <0x2a0000 0x500000>; + }; + partition@7a0000 { + label = "user"; + reg = <0x7a0000 0x860000>; + }; + }; + }; + + soc@fff00000 { + compatible = "fsl,mpc852", "fsl,pq1-soc", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + ranges = <0 0xfff00000 0x00004000>; + + PIC: interrupt-controller@0 { + interrupt-controller; + #interrupt-cells = <2>; + reg = <0 24>; + compatible = "fsl,mpc852-pic", "fsl,pq1-pic"; + }; + + cpm@9c0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc852-cpm", "fsl,cpm1", "simple-bus"; + interrupts = <0>; /* cpm error interrupt */ + interrupt-parent = <&CPM_PIC>; + reg = <0x9c0 10>; + ranges; + + muram@2000 { + compatible = "fsl,cpm-muram"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x2000>; + + data@0 { + compatible = "fsl,cpm-muram-data"; + reg = <0x800 0x1800>; + }; + }; + + brg@9f0 { + compatible = "fsl,mpc852-brg", + "fsl,cpm1-brg", + "fsl,cpm-brg"; + reg = <0x9f0 0x10>; + clock-frequency = <0>; /* Filled in by u-boot */ + }; + + CPM_PIC: interrupt-controller@930 { + interrupt-controller; + #interrupt-cells = <1>; + interrupts = <5 2 0 2>; + interrupt-parent = <&PIC>; + reg = <0x930 0x20>; + compatible = "fsl,cpm1-pic"; + }; + + /* MON-1 */ + serial@a80 { + device_type = "serial"; + compatible = "fsl,cpm1-smc-uart"; + reg = <0xa80 0x10 0x3fc0 0x40>; + interrupts = <4>; + interrupt-parent = <&CPM_PIC>; + fsl,cpm-brg = <1>; + fsl,cpm-command = <0x0090>; + current-speed = <0>; /* Filled in by u-boot */ + }; + + ethernet@a40 { + device_type = "network"; + compatible = "fsl,mpc866-scc-enet", + "fsl,cpm1-scc-enet"; + reg = <0xa40 0x18 0x3e00 0x100>; + local-mac-address = [ 00 00 00 00 00 00 ]; /* Filled in by u-boot */ + interrupts = <28>; + interrupt-parent = <&CPM_PIC>; + fsl,cpm-command = <0x80>; + fixed-link = <0 0 10 0 0>; + }; + }; + }; +}; diff --git a/arch/powerpc/configs/mgsuvd_defconfig b/arch/powerpc/configs/mgsuvd_defconfig new file mode 100644 index 00000000000..3cd6ce4be82 --- /dev/null +++ b/arch/powerpc/configs/mgsuvd_defconfig @@ -0,0 +1,872 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.26-rc2 +# Wed May 21 13:30:33 2008 +# +# CONFIG_PPC64 is not set + +# +# Processor support +# +# CONFIG_6xx is not set +# CONFIG_PPC_85xx is not set +CONFIG_PPC_8xx=y +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_8xx=y +# CONFIG_PPC_MM_SLICES is not set +CONFIG_NOT_COHERENT_CACHE=y +CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set +CONFIG_IRQ_PER_CPU=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +# CONFIG_ARCH_NO_VIRT_TO_BUS is not set +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_OF=y +# CONFIG_PPC_UDBG_16550 is not set +# CONFIG_GENERIC_TBSYNC is not set +CONFIG_AUDIT_ARCH=y +# CONFIG_DEFAULT_UIMAGE is not set +# CONFIG_PPC_DCR_NATIVE is not set +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=17 +# CONFIG_CGROUPS is not set +CONFIG_GROUP_SCHED=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +# CONFIG_SYSCTL_SYSCALL is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +# CONFIG_HOTPLUG is not set +CONFIG_PRINTK=y +# CONFIG_BUG is not set +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +# CONFIG_BASE_FULL is not set +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +# CONFIG_EPOLL is not set +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +# CONFIG_VM_EVENT_COUNTERS is not set +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=1 +# CONFIG_MODULES is not set +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_CLASSIC_RCU=y + +# +# Platform support +# +# CONFIG_PPC_MPC512x is not set +# CONFIG_PPC_MPC5121 is not set +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +CONFIG_CPM1=y +# CONFIG_MPC8XXFADS is not set +# CONFIG_MPC86XADS is not set +# CONFIG_MPC885ADS is not set +# CONFIG_PPC_EP88XC is not set +# CONFIG_PPC_ADDER875 is not set +CONFIG_PPC_MGSUVD=y + +# +# MPC8xx CPM Options +# + +# +# Generic MPC8xx Options +# +CONFIG_8xx_COPYBACK=y +CONFIG_8xx_CPU6=y +CONFIG_8xx_CPU15=y +# CONFIG_NO_UCODE_PATCH is not set +# CONFIG_USB_SOF_UCODE_PATCH is not set +# CONFIG_I2C_SPI_UCODE_PATCH is not set +CONFIG_I2C_SPI_SMC1_UCODE_PATCH=y +CONFIG_UCODE_PATCH=y +# CONFIG_PQ2ADS is not set +# CONFIG_IPIC is not set +# CONFIG_MPIC is not set +# CONFIG_MPIC_WEIRD is not set +# CONFIG_PPC_I8259 is not set +# CONFIG_PPC_RTAS is not set +# CONFIG_MMIO_NVRAM is not set +# CONFIG_PPC_MPC106 is not set +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +CONFIG_PPC_CPM_NEW_BINDING=y +# CONFIG_FSL_ULI1575 is not set +CONFIG_CPM=y + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +# CONFIG_TICK_ONESHOT is not set +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_HZ_100 is not set +# CONFIG_HZ_250 is not set +# CONFIG_HZ_300 is not set +CONFIG_HZ_1000=y +CONFIG_HZ=1000 +# CONFIG_SCHED_HRTICK is not set +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +CONFIG_MATH_EMULATION=y +# CONFIG_IOMMU_HELPER is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_HAS_WALK_MEMORY=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_FORCE_MAX_ZONEORDER=11 +# CONFIG_PROC_DEVICETREE is not set +# CONFIG_CMDLINE_BOOL is not set +# CONFIG_PM is not set +# CONFIG_SECCOMP is not set +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +CONFIG_ZONE_DMA=y +CONFIG_FSL_SOC=y +# CONFIG_PCI is not set +# CONFIG_PCI_DOMAINS is not set +# CONFIG_PCI_SYSCALL is not set +# CONFIG_PCI_QSPAN is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_HAS_RAPIDIO is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_PAGE_OFFSET=0xc0000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_PHYSICAL_START=0x00000000 +CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_START=0xfd000000 +CONFIG_CONSISTENT_SIZE=0x00200000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_OF_PARTS=y +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_NOSWAP=y +# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set +# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set +CONFIG_MTD_CFI_GEOMETRY=y +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP_OF=y +# CONFIG_MTD_CFI_FLAGADM is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +CONFIG_OF_DEVICE=y +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MISC_DEVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +# CONFIG_MACINTOSH_DRIVERS is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +CONFIG_FIXED_PHY=y +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set +CONFIG_FS_ENET=y +CONFIG_FS_ENET_HAS_SCC=y +# CONFIG_FS_ENET_HAS_FEC is not set +# CONFIG_FS_ENET_MDIO_FEC is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +# CONFIG_INPUT is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_CPM=y +CONFIG_SERIAL_CPM_CONSOLE=y +# CONFIG_SERIAL_CPM_SCC1 is not set +# CONFIG_SERIAL_CPM_SCC2 is not set +# CONFIG_SERIAL_CPM_SCC3 is not set +# CONFIG_SERIAL_CPM_SCC4 is not set +CONFIG_SERIAL_CPM_SMC1=y +# CONFIG_SERIAL_CPM_SMC2 is not set +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +CONFIG_GEN_RTC=y +# CONFIG_GEN_RTC_X is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +# CONFIG_I2C is not set +# CONFIG_SPI is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set +# CONFIG_USB_SUPPORT is not set +# CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +# CONFIG_EDAC is not set +# CONFIG_RTC_CLASS is not set +# CONFIG_DMADEVICES is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +# CONFIG_EXT2_FS_POSIX_ACL is not set +# CONFIG_EXT2_FS_SECURITY is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +# CONFIG_PROC_KCORE is not set +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +# CONFIG_NLS is not set +# CONFIG_DLM is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +CONFIG_CRC_CCITT=y +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_HAVE_LMB=y + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +# CONFIG_DEBUG_KERNEL is not set +# CONFIG_SAMPLES is not set +# CONFIG_IRQSTACKS is not set +# CONFIG_VIRQ_DEBUG is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +# CONFIG_CRYPTO_MANAGER is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +# CONFIG_CRYPTO_CBC is not set +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y +# CONFIG_VIRTUALIZATION is not set diff --git a/arch/powerpc/platforms/8xx/Kconfig b/arch/powerpc/platforms/8xx/Kconfig index 71d7562e190..48a920a98e7 100644 --- a/arch/powerpc/platforms/8xx/Kconfig +++ b/arch/powerpc/platforms/8xx/Kconfig @@ -49,6 +49,12 @@ config PPC_ADDER875 This enables support for the Analogue & Micro Adder 875 board. +config PPC_MGSUVD + bool "MGSUVD" + select CPM1 + help + This enables support for the Keymile MGSUVD board. + endchoice menu "Freescale Ethernet driver platform-specific options" diff --git a/arch/powerpc/platforms/8xx/Makefile b/arch/powerpc/platforms/8xx/Makefile index 7b71d9c8fb4..bdbfd749601 100644 --- a/arch/powerpc/platforms/8xx/Makefile +++ b/arch/powerpc/platforms/8xx/Makefile @@ -6,3 +6,4 @@ obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o obj-$(CONFIG_MPC86XADS) += mpc86xads_setup.o obj-$(CONFIG_PPC_EP88XC) += ep88xc.o obj-$(CONFIG_PPC_ADDER875) += adder875.o +obj-$(CONFIG_PPC_MGSUVD) += mgsuvd.o diff --git a/arch/powerpc/platforms/8xx/mgsuvd.c b/arch/powerpc/platforms/8xx/mgsuvd.c new file mode 100644 index 00000000000..ca3cb071772 --- /dev/null +++ b/arch/powerpc/platforms/8xx/mgsuvd.c @@ -0,0 +1,92 @@ +/* + * + * Platform setup for the Keymile mgsuvd board + * + * Heiko Schocher + * + * Copyright 2008 DENX Software Engineering GmbH + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include +#include + +#include +#include +#include +#include +#include +#include + +#include "mpc8xx.h" + +struct cpm_pin { + int port, pin, flags; +}; + +static __initdata struct cpm_pin mgsuvd_pins[] = { + /* SMC1 */ + {CPM_PORTB, 24, CPM_PIN_INPUT}, /* RX */ + {CPM_PORTB, 25, CPM_PIN_INPUT | CPM_PIN_SECONDARY}, /* TX */ + + /* SCC3 */ + {CPM_PORTA, 10, CPM_PIN_INPUT}, + {CPM_PORTA, 11, CPM_PIN_INPUT}, + {CPM_PORTA, 3, CPM_PIN_INPUT}, + {CPM_PORTA, 2, CPM_PIN_INPUT}, + {CPM_PORTC, 13, CPM_PIN_INPUT}, +}; + +static void __init init_ioports(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(mgsuvd_pins); i++) { + struct cpm_pin *pin = &mgsuvd_pins[i]; + cpm1_set_pin(pin->port, pin->pin, pin->flags); + } + + setbits16(&mpc8xx_immr->im_ioport.iop_pcso, 0x300); + cpm1_clk_setup(CPM_CLK_SCC3, CPM_CLK5, CPM_CLK_RX); + cpm1_clk_setup(CPM_CLK_SCC3, CPM_CLK6, CPM_CLK_TX); + cpm1_clk_setup(CPM_CLK_SMC1, CPM_BRG1, CPM_CLK_RTX); +} + +static void __init mgsuvd_setup_arch(void) +{ + cpm_reset(); + init_ioports(); +} + +static __initdata struct of_device_id of_bus_ids[] = { + { .compatible = "simple-bus" }, + {}, +}; + +static int __init declare_of_platform_devices(void) +{ + of_platform_bus_probe(NULL, of_bus_ids, NULL); + return 0; +} +machine_device_initcall(mgsuvd, declare_of_platform_devices); + +static int __init mgsuvd_probe(void) +{ + unsigned long root = of_get_flat_dt_root(); + return of_flat_dt_is_compatible(root, "keymile,mgsuvd"); +} + +define_machine(mgsuvd) { + .name = "MGSUVD", + .probe = mgsuvd_probe, + .setup_arch = mgsuvd_setup_arch, + .init_IRQ = mpc8xx_pics_init, + .get_irq = mpc8xx_get_irq, + .restart = mpc8xx_restart, + .calibrate_decr = mpc8xx_calibrate_decr, + .set_rtc_time = mpc8xx_set_rtc_time, + .get_rtc_time = mpc8xx_get_rtc_time, +}; -- cgit v1.2.3 From 637166337ca29459581bd2943072a9f1268fb982 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Wed, 18 Jun 2008 10:38:32 +0200 Subject: powerpc: Add support for mpc8247 based board MGCOGE from keymile. Signed-off-by: Heiko Schocher Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mgcoge.dts | 174 +++++++ arch/powerpc/configs/mgcoge_defconfig | 900 ++++++++++++++++++++++++++++++++++ arch/powerpc/platforms/82xx/Kconfig | 8 + arch/powerpc/platforms/82xx/Makefile | 1 + arch/powerpc/platforms/82xx/mgcoge.c | 129 +++++ 5 files changed, 1212 insertions(+) create mode 100644 arch/powerpc/boot/dts/mgcoge.dts create mode 100644 arch/powerpc/configs/mgcoge_defconfig create mode 100644 arch/powerpc/platforms/82xx/mgcoge.c (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mgcoge.dts b/arch/powerpc/boot/dts/mgcoge.dts new file mode 100644 index 00000000000..633255a9755 --- /dev/null +++ b/arch/powerpc/boot/dts/mgcoge.dts @@ -0,0 +1,174 @@ +/* + * Device Tree for the MGCOGE plattform from keymile + * + * Copyright 2008 DENX Software Engineering GmbH + * Heiko Schocher + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; +/ { + model = "MGCOGE"; + compatible = "keymile,mgcoge"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = ð0; + serial0 = &smc2; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,8247@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <32>; + i-cache-line-size = <32>; + d-cache-size = <16384>; + i-cache-size = <16384>; + timebase-frequency = <0>; /* Filled in by U-Boot */ + clock-frequency = <0>; /* Filled in by U-Boot */ + bus-frequency = <0>; /* Filled in by U-Boot */ + }; + }; + + localbus@f0010100 { + compatible = "fsl,mpc8247-localbus", + "fsl,pq2-localbus", + "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0xf0010100 0x40>; + + ranges = <0 0 0xfe000000 0x00400000 + 5 0 0x50000000 0x20000000 + >; /* Filled in by U-Boot */ + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0x0 0x400000>; + #address-cells = <1>; + #size-cells = <1>; + bank-width = <1>; + device-width = <1>; + partition@0 { + label = "u-boot"; + reg = <0 0x40000>; + }; + partition@40000 { + label = "env"; + reg = <0x40000 0x20000>; + }; + partition@60000 { + label = "kernel"; + reg = <0x60000 0x220000>; + }; + partition@280000 { + label = "dtb"; + reg = <0x280000 0x20000>; + }; + }; + + flash@5,0 { + compatible = "cfi-flash"; + reg = <5 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + bank-width = <2>; + device-width = <2>; + partition@0 { + label = "ramdisk"; + reg = <0 0x7a0000>; + }; + partition@7a0000 { + label = "user"; + reg = <0x7a0000 0x1860000>; + }; + }; + }; + + memory { + device_type = "memory"; + reg = <0 0>; /* Filled in by U-Boot */ + }; + + soc@f0000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8247-immr", "fsl,pq2-soc", "simple-bus"; + ranges = <0x00000000 0xf0000000 0x00053000>; + + // Temporary until code stops depending on it. + device_type = "soc"; + + cpm@119c0 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,mpc8247-cpm", "fsl,cpm2", + "simple-bus"; + reg = <0x119c0 0x30>; + ranges; + + muram { + compatible = "fsl,cpm-muram"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x10000>; + + data@0 { + compatible = "fsl,cpm-muram-data"; + reg = <0x80 0x1f80 0x9800 0x800>; + }; + }; + + brg@119f0 { + compatible = "fsl,mpc8247-brg", + "fsl,cpm2-brg", + "fsl,cpm-brg"; + reg = <0x119f0 0x10 0x115f0 0x10>; + }; + + /* Monitor port/SMC2 */ + smc2: serial@11a90 { + device_type = "serial"; + compatible = "fsl,mpc8247-smc-uart", + "fsl,cpm2-smc-uart"; + reg = <0x11a90 0x20 0x88fc 0x02>; + interrupts = <5 8>; + interrupt-parent = <&PIC>; + fsl,cpm-brg = <2>; + fsl,cpm-command = <0x21200000>; + current-speed = <0>; /* Filled in by U-Boot */ + }; + + eth0: ethernet@11a60 { + device_type = "network"; + compatible = "fsl,mpc8247-scc-enet", + "fsl,cpm2-scc-enet"; + reg = <0x11a60 0x20 0x8300 0x100 0x11390 1>; + local-mac-address = [ 00 00 00 00 00 00 ]; /* Filled in by U-Boot */ + interrupts = <43 8>; + interrupt-parent = <&PIC>; + linux,network-index = <0>; + fsl,cpm-command = <0xce00000>; + fixed-link = <0 0 10 0 0>; + }; + + }; + + PIC: interrupt-controller@10c00 { + #interrupt-cells = <2>; + interrupt-controller; + reg = <0x10c00 0x80>; + compatible = "fsl,mpc8247-pic", "fsl,pq2-pic"; + }; + }; +}; diff --git a/arch/powerpc/configs/mgcoge_defconfig b/arch/powerpc/configs/mgcoge_defconfig new file mode 100644 index 00000000000..cc9eaba8c9c --- /dev/null +++ b/arch/powerpc/configs/mgcoge_defconfig @@ -0,0 +1,900 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.26-rc2 +# Thu May 22 08:18:47 2008 +# +# CONFIG_PPC64 is not set + +# +# Processor support +# +CONFIG_6xx=y +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_8xx is not set +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_PPC_FPU=y +CONFIG_PPC_STD_MMU=y +CONFIG_PPC_STD_MMU_32=y +# CONFIG_PPC_MM_SLICES is not set +# CONFIG_SMP is not set +CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set +CONFIG_IRQ_PER_CPU=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +# CONFIG_ARCH_NO_VIRT_TO_BUS is not set +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_OF=y +# CONFIG_PPC_UDBG_16550 is not set +# CONFIG_GENERIC_TBSYNC is not set +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +# CONFIG_DEFAULT_UIMAGE is not set +# CONFIG_PPC_DCR_NATIVE is not set +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +# CONFIG_EXPERIMENTAL is not set +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_KALLSYMS=y +CONFIG_KALLSYMS_ALL=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_MODULES is not set +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +# CONFIG_IOSCHED_AS is not set +CONFIG_IOSCHED_DEADLINE=y +# CONFIG_IOSCHED_CFQ is not set +# CONFIG_DEFAULT_AS is not set +CONFIG_DEFAULT_DEADLINE=y +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="deadline" +CONFIG_CLASSIC_RCU=y + +# +# Platform support +# +# CONFIG_PPC_MULTIPLATFORM is not set +CONFIG_PPC_82xx=y +# CONFIG_PPC_83xx is not set +# CONFIG_PPC_86xx is not set +# CONFIG_PPC_MPC512x is not set +# CONFIG_PPC_MPC5121 is not set +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_MPC8272_ADS is not set +# CONFIG_PQ2FADS is not set +# CONFIG_EP8248E is not set +CONFIG_MGCOGE=y +# CONFIG_PQ2ADS is not set +CONFIG_8260=y +CONFIG_8272=y +# CONFIG_IPIC is not set +# CONFIG_MPIC is not set +# CONFIG_MPIC_WEIRD is not set +# CONFIG_PPC_I8259 is not set +# CONFIG_PPC_RTAS is not set +# CONFIG_MMIO_NVRAM is not set +# CONFIG_PPC_MPC106 is not set +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +CONFIG_CPM2=y +CONFIG_PPC_CPM_NEW_BINDING=y +# CONFIG_FSL_ULI1575 is not set +CONFIG_CPM=y + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +# CONFIG_TICK_ONESHOT is not set +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +# CONFIG_SCHED_HRTICK is not set +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +CONFIG_BINFMT_MISC=y +# CONFIG_IOMMU_HELPER is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_HAS_WALK_MEMORY=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_FORCE_MAX_ZONEORDER=11 +CONFIG_PROC_DEVICETREE=y +# CONFIG_CMDLINE_BOOL is not set +# CONFIG_PM is not set +# CONFIG_SECCOMP is not set +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +CONFIG_ZONE_DMA=y +CONFIG_FSL_SOC=y +# CONFIG_PCI is not set +# CONFIG_PCI_DOMAINS is not set +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set +# CONFIG_HAS_RAPIDIO is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_PAGE_OFFSET=0xc0000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_PHYSICAL_START=0x00000000 +CONFIG_TASK_SIZE=0xc0000000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_IP_VS is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +CONFIG_NETFILTER=y +# CONFIG_NETFILTER_DEBUG is not set +CONFIG_NETFILTER_ADVANCED=y + +# +# Core Netfilter Configuration +# +# CONFIG_NETFILTER_NETLINK_QUEUE is not set +# CONFIG_NETFILTER_NETLINK_LOG is not set +# CONFIG_NF_CONNTRACK is not set +# CONFIG_NETFILTER_XTABLES is not set + +# +# IP: Netfilter Configuration +# +# CONFIG_IP_NF_QUEUE is not set +# CONFIG_IP_NF_IPTABLES is not set +# CONFIG_IP_NF_ARPTABLES is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_CONCAT=y +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_OF_PARTS=y +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +# CONFIG_MTD_BLOCK is not set +# CONFIG_MTD_BLOCK_RO is not set +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_NOSWAP=y +# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set +# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set +CONFIG_MTD_CFI_GEOMETRY=y +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_AMDSTD=y +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP_OF=y +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +CONFIG_OF_DEVICE=y +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MISC_DEVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +# CONFIG_MACINTOSH_DRIVERS is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +CONFIG_FIXED_PHY=y +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set +CONFIG_FS_ENET=y +CONFIG_FS_ENET_HAS_SCC=y +# CONFIG_FS_ENET_HAS_FCC is not set +# CONFIG_FS_ENET_MDIO_FCC is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +# CONFIG_INPUT is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_CPM=y +CONFIG_SERIAL_CPM_CONSOLE=y +# CONFIG_SERIAL_CPM_SCC1 is not set +# CONFIG_SERIAL_CPM_SCC2 is not set +# CONFIG_SERIAL_CPM_SCC3 is not set +# CONFIG_SERIAL_CPM_SCC4 is not set +CONFIG_SERIAL_CPM_SMC1=y +CONFIG_SERIAL_CPM_SMC2=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +# CONFIG_GEN_RTC is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_I2C is not set +# CONFIG_SPI is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set +# CONFIG_USB_SUPPORT is not set +# CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +# CONFIG_RTC_CLASS is not set +# CONFIG_DMADEVICES is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_FS_XATTR is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +CONFIG_AUTOFS4_FS=y +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_HFSPLUS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +CONFIG_NLS_ASCII=y +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=y + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_HAVE_LMB=y + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +# CONFIG_DETECT_SOFTLOCKUP is not set +# CONFIG_SCHED_DEBUG is not set +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_DEBUGGER is not set +# CONFIG_KGDB_CONSOLE is not set +# CONFIG_IRQSTACKS is not set +# CONFIG_VIRQ_DEBUG is not set +CONFIG_BDI_SWITCH=y +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=y +CONFIG_CRYPTO_PCBC=y + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +# CONFIG_CRYPTO_HW is not set +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y +# CONFIG_VIRTUALIZATION is not set diff --git a/arch/powerpc/platforms/82xx/Kconfig b/arch/powerpc/platforms/82xx/Kconfig index 75eb1ede549..30f008b2f92 100644 --- a/arch/powerpc/platforms/82xx/Kconfig +++ b/arch/powerpc/platforms/82xx/Kconfig @@ -38,6 +38,14 @@ config EP8248E This board is also resold by Freescale as the QUICCStart MPC8248 Evaluation System and/or the CWH-PPC-8248N-VE. +config MGCOGE + bool "Keymile MGCOGE" + select 8272 + select 8260 + select FSL_SOC + help + This enables support for the Keymile MGCOGE board. + endif config PQ2ADS diff --git a/arch/powerpc/platforms/82xx/Makefile b/arch/powerpc/platforms/82xx/Makefile index 6cd5cd59bf2..d982793f4db 100644 --- a/arch/powerpc/platforms/82xx/Makefile +++ b/arch/powerpc/platforms/82xx/Makefile @@ -6,3 +6,4 @@ obj-$(CONFIG_CPM2) += pq2.o obj-$(CONFIG_PQ2_ADS_PCI_PIC) += pq2ads-pci-pic.o obj-$(CONFIG_PQ2FADS) += pq2fads.o obj-$(CONFIG_EP8248E) += ep8248e.o +obj-$(CONFIG_MGCOGE) += mgcoge.o diff --git a/arch/powerpc/platforms/82xx/mgcoge.c b/arch/powerpc/platforms/82xx/mgcoge.c new file mode 100644 index 00000000000..c2af169c1d1 --- /dev/null +++ b/arch/powerpc/platforms/82xx/mgcoge.c @@ -0,0 +1,129 @@ +/* + * Keymile mgcoge support + * Copyright 2008 DENX Software Engineering GmbH + * Author: Heiko Schocher + * + * based on code from: + * Copyright 2007 Freescale Semiconductor, Inc. + * Author: Scott Wood + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +#include "pq2.h" + +static void __init mgcoge_pic_init(void) +{ + struct device_node *np = of_find_compatible_node(NULL, NULL, "fsl,pq2-pic"); + if (!np) { + printk(KERN_ERR "PIC init: can not find cpm-pic node\n"); + return; + } + + cpm2_pic_init(np); + of_node_put(np); +} + +struct cpm_pin { + int port, pin, flags; +}; + +static __initdata struct cpm_pin mgcoge_pins[] = { + + /* SMC2 */ + {1, 8, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, + {1, 9, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY}, + + /* SCC4 */ + {3, 25, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, + {3, 24, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, + {3, 9, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, + {3, 8, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, + {4, 22, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, + {4, 21, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY}, +}; + +static void __init init_ioports(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(mgcoge_pins); i++) { + const struct cpm_pin *pin = &mgcoge_pins[i]; + cpm2_set_pin(pin->port - 1, pin->pin, pin->flags); + } + + cpm2_smc_clk_setup(CPM_CLK_SMC2, CPM_BRG8); + cpm2_clk_setup(CPM_CLK_SCC4, CPM_CLK7, CPM_CLK_RX); + cpm2_clk_setup(CPM_CLK_SCC4, CPM_CLK8, CPM_CLK_TX); +} + +static void __init mgcoge_setup_arch(void) +{ + if (ppc_md.progress) + ppc_md.progress("mgcoge_setup_arch()", 0); + + cpm2_reset(); + + /* When this is set, snooping CPM DMA from RAM causes + * machine checks. See erratum SIU18. + */ + clrbits32(&cpm2_immr->im_siu_conf.siu_82xx.sc_bcr, MPC82XX_BCR_PLDP); + + init_ioports(); + + if (ppc_md.progress) + ppc_md.progress("mgcoge_setup_arch(), finish", 0); +} + +static __initdata struct of_device_id of_bus_ids[] = { + { .compatible = "simple-bus", }, + {}, +}; + +static int __init declare_of_platform_devices(void) +{ + of_platform_bus_probe(NULL, of_bus_ids, NULL); + + return 0; +} +machine_device_initcall(mgcoge, declare_of_platform_devices); + +/* + * Called very early, device-tree isn't unflattened + */ +static int __init mgcoge_probe(void) +{ + unsigned long root = of_get_flat_dt_root(); + return of_flat_dt_is_compatible(root, "keymile,mgcoge"); +} + +define_machine(mgcoge) +{ + .name = "Keymile MGCOGE", + .probe = mgcoge_probe, + .setup_arch = mgcoge_setup_arch, + .init_IRQ = mgcoge_pic_init, + .get_irq = cpm2_get_irq, + .calibrate_decr = generic_calibrate_decr, + .restart = pq2_restart, + .progress = udbg_progress, +}; -- cgit v1.2.3 From 307db95882fdfba372a0639e8e238cf8c542f430 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 14 Aug 2008 21:13:42 +0400 Subject: powerpc/83xx: mpc836x_mds: add support for the nor flash This patch adds the localbus node, moves the bcsr node into the localbus node, and adds the flash node. Also enable MTD support in the defconfig. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc836x_mds.dts | 23 ++++++- arch/powerpc/configs/83xx/mpc836x_mds_defconfig | 79 ++++++++++++++++++++++++- 2 files changed, 98 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts index a3b76a70995..ada8446ab3c 100644 --- a/arch/powerpc/boot/dts/mpc836x_mds.dts +++ b/arch/powerpc/boot/dts/mpc836x_mds.dts @@ -52,9 +52,26 @@ reg = <0x00000000 0x10000000>; }; - bcsr@f8000000 { - device_type = "board-control"; - reg = <0xf8000000 0x8000>; + localbus@e0005000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc8360-localbus", "fsl,pq2pro-localbus", + "simple-bus"; + reg = <0xe0005000 0xd8>; + ranges = <0 0 0xfe000000 0x02000000 + 1 0 0xf8000000 0x00008000>; + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0 0x2000000>; + bank-width = <2>; + device-width = <1>; + }; + + bcsr@1,0 { + device_type = "board-control"; + reg = <1 0 0x8000>; + }; }; soc8360@e0000000 { diff --git a/arch/powerpc/configs/83xx/mpc836x_mds_defconfig b/arch/powerpc/configs/83xx/mpc836x_mds_defconfig index e029e9e1462..cf2706a5f34 100644 --- a/arch/powerpc/configs/83xx/mpc836x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc836x_mds_defconfig @@ -383,7 +383,84 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set -# CONFIG_MTD is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_OF_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CFI_AMDSTD=y +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP_OF=y +# CONFIG_MTD_INTEL_VR_NOR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y # CONFIG_PARPORT is not set -- cgit v1.2.3 From 82331ab15f14786f3d8e874efb76462685e3bfa0 Mon Sep 17 00:00:00 2001 From: Becky Bruce Date: Thu, 21 Aug 2008 13:50:22 -0500 Subject: powerpc/85xx: fix build warning, remove silly cast This fixes a build warning when PHYS_64BIT is enabled, and removes an unnecessary cast to phys_addr_t (the variable being cast is already a phys_addr_t) Signed-off-by: Becky Bruce Signed-off-by: Kumar Gala --- arch/powerpc/mm/fsl_booke_mmu.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/mm/fsl_booke_mmu.c b/arch/powerpc/mm/fsl_booke_mmu.c index ce10e2b1b90..23cee39534f 100644 --- a/arch/powerpc/mm/fsl_booke_mmu.c +++ b/arch/powerpc/mm/fsl_booke_mmu.c @@ -202,7 +202,7 @@ adjust_total_lowmem(void) cam_max_size = max_lowmem_size; /* adjust lowmem size to max_lowmem_size */ - ram = min(max_lowmem_size, (phys_addr_t)total_lowmem); + ram = min(max_lowmem_size, total_lowmem); /* Calculate CAM values */ __cam0 = 1UL << 2 * (__ilog2(ram) / 2); @@ -225,7 +225,8 @@ adjust_total_lowmem(void) printk(KERN_INFO "Memory CAM mapping: CAM0=%ldMb, CAM1=%ldMb," " CAM2=%ldMb residual: %ldMb\n", __cam0 >> 20, __cam1 >> 20, __cam2 >> 20, - (total_lowmem - __cam0 - __cam1 - __cam2) >> 20); + (long int)((total_lowmem - __cam0 - __cam1 - __cam2) + >> 20)); __max_low_memory = __cam0 + __cam1 + __cam2; __initial_memory_limit_addr = memstart_addr + __max_low_memory; } -- cgit v1.2.3 From 66576a87dda18cede6a728685366c9c0fedd1742 Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Wed, 3 Sep 2008 16:02:25 -0400 Subject: powerpc/sbc8560: fix compile warning on CPM pin array This is just a parallel of a5dc66e2ab2e2cf641346b056a69a67cfcf9458c applied to the sbc8560 board. Signed-off-by: Paul Gortmaker Signed-off-by: Kumar Gala --- arch/powerpc/platforms/85xx/sbc8560.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/85xx/sbc8560.c b/arch/powerpc/platforms/85xx/sbc8560.c index 6509ade7166..e0cf0602d8b 100644 --- a/arch/powerpc/platforms/85xx/sbc8560.c +++ b/arch/powerpc/platforms/85xx/sbc8560.c @@ -156,7 +156,7 @@ static void __init init_ioports(void) int i; for (i = 0; i < ARRAY_SIZE(sbc8560_pins); i++) { - struct cpm_pin *pin = &sbc8560_pins[i]; + const struct cpm_pin *pin = &sbc8560_pins[i]; cpm2_set_pin(pin->port, pin->pin, pin->flags); } -- cgit v1.2.3 From 54508214cf2f88ad1288e8836032545e0357ebde Mon Sep 17 00:00:00 2001 From: Martyn Welch Date: Tue, 16 Sep 2008 10:57:47 +0100 Subject: powerpc: Board support for GE Fanuc SBC610 Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D). This is the basic board support for GE Fanuc's SBC610, a 6U single board computer, based on Freescale's MPC8641D. Signed-off-by: Martyn Welch Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/gef_sbc610.dts | 260 +++++++++++++++++++++++++++++++ arch/powerpc/platforms/86xx/Kconfig | 9 +- arch/powerpc/platforms/86xx/Makefile | 1 + arch/powerpc/platforms/86xx/gef_sbc610.c | 149 ++++++++++++++++++ 4 files changed, 418 insertions(+), 1 deletion(-) create mode 100644 arch/powerpc/boot/dts/gef_sbc610.dts create mode 100644 arch/powerpc/platforms/86xx/gef_sbc610.c (limited to 'arch') diff --git a/arch/powerpc/boot/dts/gef_sbc610.dts b/arch/powerpc/boot/dts/gef_sbc610.dts new file mode 100644 index 00000000000..80b79e4adc7 --- /dev/null +++ b/arch/powerpc/boot/dts/gef_sbc610.dts @@ -0,0 +1,260 @@ +/* + * GE Fanuc SBC610 Device Tree Source + * + * Copyright 2008 GE Fanuc Intelligent Platforms Embedded Systems, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * Based on: SBS CM6 Device Tree Source + * Copyright 2007 SBS Technologies GmbH & Co. KG + * And: mpc8641_hpcn.dts (MPC8641 HPCN Device Tree Source) + * Copyright 2006 Freescale Semiconductor Inc. + */ + +/* + * Compiled with dtc -I dts -O dtb -o gef_sbc610.dtb gef_sbc610.dts + */ + +/dts-v1/; + +/ { + model = "GEF_SBC610"; + compatible = "gef,sbc610"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet0; + ethernet1 = &enet1; + serial0 = &serial0; + serial1 = &serial1; + pci0 = &pci0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,8641@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <32>; // 32 bytes + i-cache-line-size = <32>; // 32 bytes + d-cache-size = <32768>; // L1, 32K + i-cache-size = <32768>; // L1, 32K + timebase-frequency = <0>; // From uboot + bus-frequency = <0>; // From uboot + clock-frequency = <0>; // From uboot + }; + PowerPC,8641@1 { + device_type = "cpu"; + reg = <1>; + d-cache-line-size = <32>; // 32 bytes + i-cache-line-size = <32>; // 32 bytes + d-cache-size = <32768>; // L1, 32K + i-cache-size = <32768>; // L1, 32K + timebase-frequency = <0>; // From uboot + bus-frequency = <0>; // From uboot + clock-frequency = <0>; // From uboot + }; + }; + + memory { + device_type = "memory"; + reg = <0x0 0x40000000>; // set by uboot + }; + + soc@fef00000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "soc"; + compatible = "simple-bus"; + ranges = <0x0 0xfef00000 0x00100000>; + reg = <0xfef00000 0x100000>; // CCSRBAR 1M + bus-frequency = <0>; + + i2c1: i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <0x2b 0x2>; + interrupt-parent = <&mpic>; + dfsrr; + + eti@6b { + compatible = "dallas,ds1682"; + reg = <0x6b>; + }; + }; + + i2c2: i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <0x2b 0x2>; + interrupt-parent = <&mpic>; + dfsrr; + }; + + dma@21300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8641-dma", "fsl,eloplus-dma"; + reg = <0x21300 0x4>; + ranges = <0x0 0x21100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8641-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupt-parent = <&mpic>; + interrupts = <20 2>; + }; + dma-channel@80 { + compatible = "fsl,mpc8641-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupt-parent = <&mpic>; + interrupts = <21 2>; + }; + dma-channel@100 { + compatible = "fsl,mpc8641-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupt-parent = <&mpic>; + interrupts = <22 2>; + }; + dma-channel@180 { + compatible = "fsl,mpc8641-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupt-parent = <&mpic>; + interrupts = <23 2>; + }; + }; + + mdio@24520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-mdio"; + reg = <0x24520 0x20>; + + phy0: ethernet-phy@0 { + interrupt-parent = <&mpic>; + interrupts = <0x0 0x1>; + reg = <1>; + }; + phy2: ethernet-phy@2 { + interrupt-parent = <&mpic>; + interrupts = <0x0 0x1>; + reg = <3>; + }; + }; + + enet0: ethernet@24000 { + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>; + interrupt-parent = <&mpic>; + phy-handle = <&phy0>; + phy-connection-type = "gmii"; + }; + + enet1: ethernet@26000 { + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar"; + reg = <0x26000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <0x1f 0x2 0x20 0x2 0x21 0x2>; + interrupt-parent = <&mpic>; + phy-handle = <&phy2>; + phy-connection-type = "gmii"; + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4500 0x100>; + clock-frequency = <0>; + interrupts = <0x2a 0x2>; + interrupt-parent = <&mpic>; + }; + + serial1: serial@4600 { + cell-index = <1>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4600 0x100>; + clock-frequency = <0>; + interrupts = <0x1c 0x2>; + interrupt-parent = <&mpic>; + }; + + mpic: pic@40000 { + clock-frequency = <0>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x40000 0x40000>; + compatible = "chrp,open-pic"; + device_type = "open-pic"; + }; + + global-utilities@e0000 { + compatible = "fsl,mpc8641-guts"; + reg = <0xe0000 0x1000>; + fsl,has-rstcr; + }; + }; + + pci0: pcie@fef08000 { + compatible = "fsl,mpc8641-pcie"; + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xfef08000 0x1000>; + bus-range = <0x0 0xff>; + ranges = <0x02000000 0x0 0x80000000 0x80000000 0x0 0x40000000 + 0x01000000 0x0 0x00000000 0xfe000000 0x0 0x00400000>; + clock-frequency = <33333333>; + interrupt-parent = <&mpic>; + interrupts = <0x18 0x2>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + 0x0000 0x0 0x0 0x1 &mpic 0x0 0x1 + 0x0000 0x0 0x0 0x2 &mpic 0x1 0x1 + 0x0000 0x0 0x0 0x3 &mpic 0x2 0x1 + 0x0000 0x0 0x0 0x4 &mpic 0x3 0x1 + >; + + pcie@0 { + reg = <0 0 0 0 0>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + ranges = <0x02000000 0x0 0x80000000 + 0x02000000 0x0 0x80000000 + 0x0 0x40000000 + + 0x01000000 0x0 0x00000000 + 0x01000000 0x0 0x00000000 + 0x0 0x00400000>; + }; + }; +}; diff --git a/arch/powerpc/platforms/86xx/Kconfig b/arch/powerpc/platforms/86xx/Kconfig index 9355a526943..77dd797a258 100644 --- a/arch/powerpc/platforms/86xx/Kconfig +++ b/arch/powerpc/platforms/86xx/Kconfig @@ -31,6 +31,13 @@ config MPC8610_HPCD help This option enables support for the MPC8610 HPCD board. +config GEF_SBC610 + bool "GE Fanuc SBC610" + select DEFAULT_UIMAGE + select HAS_RAPIDIO + help + This option enables support for GE Fanuc's SBC610. + endif config MPC8641 @@ -39,7 +46,7 @@ config MPC8641 select FSL_PCI if PCI select PPC_UDBG_16550 select MPIC - default y if MPC8641_HPCN || SBC8641D + default y if MPC8641_HPCN || SBC8641D || GEF_SBC610 config MPC8610 bool diff --git a/arch/powerpc/platforms/86xx/Makefile b/arch/powerpc/platforms/86xx/Makefile index 8fee37dec79..cb9fc8f4360 100644 --- a/arch/powerpc/platforms/86xx/Makefile +++ b/arch/powerpc/platforms/86xx/Makefile @@ -7,3 +7,4 @@ obj-$(CONFIG_SMP) += mpc86xx_smp.o obj-$(CONFIG_MPC8641_HPCN) += mpc86xx_hpcn.o obj-$(CONFIG_SBC8641D) += sbc8641d.o obj-$(CONFIG_MPC8610_HPCD) += mpc8610_hpcd.o +obj-$(CONFIG_GEF_SBC610) += gef_sbc610.o diff --git a/arch/powerpc/platforms/86xx/gef_sbc610.c b/arch/powerpc/platforms/86xx/gef_sbc610.c new file mode 100644 index 00000000000..3543a9e6761 --- /dev/null +++ b/arch/powerpc/platforms/86xx/gef_sbc610.c @@ -0,0 +1,149 @@ +/* + * GE Fanuc SBC610 board support + * + * Author: Martyn Welch + * + * Copyright 2008 GE Fanuc Intelligent Platforms Embedded Systems, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * Based on: mpc86xx_hpcn.c (MPC86xx HPCN board specific routines) + * Copyright 2006 Freescale Semiconductor Inc. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include + +#include "mpc86xx.h" + +#undef DEBUG + +#ifdef DEBUG +#define DBG (fmt...) do { printk(KERN_ERR "SBC610: " fmt); } while (0) +#else +#define DBG (fmt...) do { } while (0) +#endif + +static void __init gef_sbc610_setup_arch(void) +{ +#ifdef CONFIG_PCI + struct device_node *np; + + for_each_compatible_node(np, "pci", "fsl,mpc8641-pcie") { + fsl_add_bridge(np, 1); + } +#endif + + printk(KERN_INFO "GE Fanuc Intelligent Platforms SBC610 6U VPX SBC\n"); + +#ifdef CONFIG_SMP + mpc86xx_smp_init(); +#endif +} + + +static void gef_sbc610_show_cpuinfo(struct seq_file *m) +{ + struct device_node *root; + uint memsize = total_memory; + const char *model = ""; + uint svid = mfspr(SPRN_SVR); + + seq_printf(m, "Vendor\t\t: GE Fanuc Intelligent Platforms\n"); + + root = of_find_node_by_path("/"); + if (root) + model = of_get_property(root, "model", NULL); + seq_printf(m, "Machine\t\t: %s\n", model); + of_node_put(root); + + seq_printf(m, "SVR\t\t: 0x%x\n", svid); + seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024)); +} + + +/* + * Called very early, device-tree isn't unflattened + * + * This function is called to determine whether the BSP is compatible with the + * supplied device-tree, which is assumed to be the correct one for the actual + * board. It is expected thati, in the future, a kernel may support multiple + * boards. + */ +static int __init gef_sbc610_probe(void) +{ + unsigned long root = of_get_flat_dt_root(); + + if (of_flat_dt_is_compatible(root, "gef,sbc610")) + return 1; + + return 0; +} + +static long __init mpc86xx_time_init(void) +{ + unsigned int temp; + + /* Set the time base to zero */ + mtspr(SPRN_TBWL, 0); + mtspr(SPRN_TBWU, 0); + + temp = mfspr(SPRN_HID0); + temp |= HID0_TBEN; + mtspr(SPRN_HID0, temp); + asm volatile("isync"); + + return 0; +} + +static __initdata struct of_device_id of_bus_ids[] = { + { .compatible = "simple-bus", }, + {}, +}; + +static int __init declare_of_platform_devices(void) +{ + printk(KERN_DEBUG "Probe platform devices\n"); + of_platform_bus_probe(NULL, of_bus_ids, NULL); + + return 0; +} +machine_device_initcall(gef_sbc610, declare_of_platform_devices); + +define_machine(gef_sbc610) { + .name = "GE Fanuc SBC610", + .probe = gef_sbc610_probe, + .setup_arch = gef_sbc610_setup_arch, + .init_IRQ = mpc86xx_init_irq, + .show_cpuinfo = gef_sbc610_show_cpuinfo, + .get_irq = mpic_get_irq, + .restart = fsl_rstcr_restart, + .time_init = mpc86xx_time_init, + .calibrate_decr = generic_calibrate_decr, + .progress = udbg_progress, +#ifdef CONFIG_PCI + .pcibios_fixup_bus = fsl_pcibios_fixup_bus, +#endif +}; -- cgit v1.2.3 From 1a9314a0f6f71cf13ddf9e58f1d4f507a5265056 Mon Sep 17 00:00:00 2001 From: Martyn Welch Date: Tue, 16 Sep 2008 10:57:52 +0100 Subject: powerpc: Default configuration for GE Fanuc SBC610 Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D). This is the default config file for GE Fanuc's SBC610, a 6U single board computer, based on Freescale's MPC8641D. Signed-off-by: Martyn Welch Signed-off-by: Kumar Gala --- arch/powerpc/configs/86xx/gef_sbc610_defconfig | 1654 ++++++++++++++++++++++++ 1 file changed, 1654 insertions(+) create mode 100644 arch/powerpc/configs/86xx/gef_sbc610_defconfig (limited to 'arch') diff --git a/arch/powerpc/configs/86xx/gef_sbc610_defconfig b/arch/powerpc/configs/86xx/gef_sbc610_defconfig new file mode 100644 index 00000000000..f589489449d --- /dev/null +++ b/arch/powerpc/configs/86xx/gef_sbc610_defconfig @@ -0,0 +1,1654 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.26-rc5 +# Wed Jun 11 12:06:53 2008 +# +# CONFIG_PPC64 is not set + +# +# Processor support +# +CONFIG_6xx=y +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_8xx is not set +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_PPC_FPU=y +CONFIG_ALTIVEC=y +CONFIG_PPC_STD_MMU=y +CONFIG_PPC_STD_MMU_32=y +# CONFIG_PPC_MM_SLICES is not set +CONFIG_SMP=y +CONFIG_NR_CPUS=2 +CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set +CONFIG_IRQ_PER_CPU=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_GENERIC_LOCKBREAK=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +# CONFIG_ARCH_NO_VIRT_TO_BUS is not set +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_OF=y +CONFIG_PPC_UDBG_16550=y +CONFIG_GENERIC_TBSYNC=y +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +CONFIG_DEFAULT_UIMAGE=y +# CONFIG_PPC_DCR_NATIVE is not set +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +CONFIG_BSD_PROCESS_ACCT=y +CONFIG_BSD_PROCESS_ACCT_V3=y +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_GROUP_SCHED=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +CONFIG_RELAY=y +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_STOP_MACHINE=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +CONFIG_DEFAULT_CFQ=y +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y + +# +# Platform support +# +# CONFIG_PPC_MULTIPLATFORM is not set +# CONFIG_PPC_82xx is not set +# CONFIG_PPC_83xx is not set +CONFIG_PPC_86xx=y +# CONFIG_PPC_MPC512x is not set +# CONFIG_PPC_MPC5121 is not set +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PQ2ADS is not set +# CONFIG_MPC8641_HPCN is not set +# CONFIG_SBC8641D is not set +# CONFIG_MPC8610_HPCD is not set +CONFIG_GEF_SBC610=y +CONFIG_MPC8641=y +# CONFIG_IPIC is not set +CONFIG_MPIC=y +# CONFIG_MPIC_WEIRD is not set +# CONFIG_PPC_I8259 is not set +# CONFIG_PPC_RTAS is not set +# CONFIG_MMIO_NVRAM is not set +# CONFIG_PPC_MPC106 is not set +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +# CONFIG_FSL_ULI1575 is not set + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +# CONFIG_NO_HZ is not set +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_HZ_100 is not set +# CONFIG_HZ_250 is not set +# CONFIG_HZ_300 is not set +CONFIG_HZ_1000=y +CONFIG_HZ=1000 +# CONFIG_SCHED_HRTICK is not set +# CONFIG_PREEMPT_NONE is not set +# CONFIG_PREEMPT_VOLUNTARY is not set +CONFIG_PREEMPT=y +# CONFIG_PREEMPT_RCU is not set +CONFIG_BINFMT_ELF=y +CONFIG_BINFMT_MISC=m +# CONFIG_IOMMU_HELPER is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_HAS_WALK_MEMORY=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y +CONFIG_IRQ_ALL_CPUS=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_FORCE_MAX_ZONEORDER=11 +# CONFIG_PROC_DEVICETREE is not set +# CONFIG_CMDLINE_BOOL is not set +# CONFIG_PM is not set +CONFIG_SECCOMP=y +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +CONFIG_ZONE_DMA=y +CONFIG_GENERIC_ISA_DMA=y +CONFIG_PPC_INDIRECT_PCI=y +CONFIG_FSL_SOC=y +CONFIG_FSL_PCI=y +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_SYSCALL=y +CONFIG_PCIEPORTBUS=y +CONFIG_PCIEAER=y +# CONFIG_PCIEASPM is not set +CONFIG_ARCH_SUPPORTS_MSI=y +# CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y +CONFIG_PCI_DEBUG=y +# CONFIG_PCCARD is not set +# CONFIG_HOTPLUG_PCI is not set +CONFIG_HAS_RAPIDIO=y +# CONFIG_RAPIDIO is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_PAGE_OFFSET=0xc0000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_PHYSICAL_START=0x00000000 +CONFIG_TASK_SIZE=0xc0000000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=m +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +CONFIG_NET_KEY=m +# CONFIG_NET_KEY_MIGRATE is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_ADVANCED_ROUTER=y +CONFIG_ASK_IP_FIB_HASH=y +# CONFIG_IP_FIB_TRIE is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_MULTIPLE_TABLES=y +CONFIG_IP_ROUTE_MULTIPATH=y +CONFIG_IP_ROUTE_VERBOSE=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +CONFIG_NET_IPIP=m +CONFIG_NET_IPGRE=m +CONFIG_NET_IPGRE_BROADCAST=y +CONFIG_IP_MROUTE=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +CONFIG_INET_AH=m +CONFIG_INET_ESP=m +CONFIG_INET_IPCOMP=m +CONFIG_INET_XFRM_TUNNEL=m +CONFIG_INET_TUNNEL=m +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IP_VS is not set +CONFIG_IPV6=m +# CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +CONFIG_INET6_AH=m +CONFIG_INET6_ESP=m +CONFIG_INET6_IPCOMP=m +# CONFIG_IPV6_MIP6 is not set +CONFIG_INET6_XFRM_TUNNEL=m +CONFIG_INET6_TUNNEL=m +CONFIG_INET6_XFRM_MODE_TRANSPORT=m +CONFIG_INET6_XFRM_MODE_TUNNEL=m +CONFIG_INET6_XFRM_MODE_BEET=m +# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set +CONFIG_IPV6_SIT=m +CONFIG_IPV6_NDISC_NODETYPE=y +CONFIG_IPV6_TUNNEL=m +# CONFIG_IPV6_MULTIPLE_TABLES is not set +# CONFIG_IPV6_MROUTE is not set +# CONFIG_NETLABEL is not set +# CONFIG_NETWORK_SECMARK is not set +CONFIG_NETFILTER=y +# CONFIG_NETFILTER_DEBUG is not set +CONFIG_NETFILTER_ADVANCED=y +CONFIG_BRIDGE_NETFILTER=y + +# +# Core Netfilter Configuration +# +# CONFIG_NETFILTER_NETLINK_QUEUE is not set +# CONFIG_NETFILTER_NETLINK_LOG is not set +# CONFIG_NF_CONNTRACK is not set +CONFIG_NETFILTER_XTABLES=m +# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set +# CONFIG_NETFILTER_XT_TARGET_DSCP is not set +# CONFIG_NETFILTER_XT_TARGET_MARK is not set +# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set +# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set +# CONFIG_NETFILTER_XT_TARGET_RATEEST is not set +# CONFIG_NETFILTER_XT_TARGET_TRACE is not set +# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set +# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set +# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set +# CONFIG_NETFILTER_XT_MATCH_DCCP is not set +# CONFIG_NETFILTER_XT_MATCH_DSCP is not set +# CONFIG_NETFILTER_XT_MATCH_ESP is not set +# CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set +# CONFIG_NETFILTER_XT_MATCH_LENGTH is not set +# CONFIG_NETFILTER_XT_MATCH_LIMIT is not set +# CONFIG_NETFILTER_XT_MATCH_MAC is not set +# CONFIG_NETFILTER_XT_MATCH_MARK is not set +# CONFIG_NETFILTER_XT_MATCH_OWNER is not set +# CONFIG_NETFILTER_XT_MATCH_POLICY is not set +# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set +# CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set +# CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set +# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set +# CONFIG_NETFILTER_XT_MATCH_RATEEST is not set +# CONFIG_NETFILTER_XT_MATCH_REALM is not set +# CONFIG_NETFILTER_XT_MATCH_SCTP is not set +# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set +# CONFIG_NETFILTER_XT_MATCH_STRING is not set +# CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set +# CONFIG_NETFILTER_XT_MATCH_TIME is not set +# CONFIG_NETFILTER_XT_MATCH_U32 is not set +# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set + +# +# IP: Netfilter Configuration +# +CONFIG_IP_NF_QUEUE=m +CONFIG_IP_NF_IPTABLES=m +CONFIG_IP_NF_MATCH_RECENT=m +CONFIG_IP_NF_MATCH_ECN=m +# CONFIG_IP_NF_MATCH_AH is not set +CONFIG_IP_NF_MATCH_TTL=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m +CONFIG_IP_NF_FILTER=m +CONFIG_IP_NF_TARGET_REJECT=m +CONFIG_IP_NF_TARGET_LOG=m +CONFIG_IP_NF_TARGET_ULOG=m +CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_ECN=m +# CONFIG_IP_NF_TARGET_TTL is not set +CONFIG_IP_NF_RAW=m +CONFIG_IP_NF_ARPTABLES=m +CONFIG_IP_NF_ARPFILTER=m +CONFIG_IP_NF_ARP_MANGLE=m + +# +# IPv6: Netfilter Configuration +# +CONFIG_IP6_NF_QUEUE=m +CONFIG_IP6_NF_IPTABLES=m +CONFIG_IP6_NF_MATCH_RT=m +CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_HL=m +CONFIG_IP6_NF_MATCH_IPV6HEADER=m +# CONFIG_IP6_NF_MATCH_AH is not set +# CONFIG_IP6_NF_MATCH_MH is not set +CONFIG_IP6_NF_MATCH_EUI64=m +CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_TARGET_LOG=m +# CONFIG_IP6_NF_TARGET_REJECT is not set +CONFIG_IP6_NF_MANGLE=m +# CONFIG_IP6_NF_TARGET_HL is not set +CONFIG_IP6_NF_RAW=m + +# +# Bridge: Netfilter Configuration +# +# CONFIG_BRIDGE_NF_EBTABLES is not set +# CONFIG_IP_DCCP is not set +CONFIG_IP_SCTP=m +# CONFIG_SCTP_DBG_MSG is not set +# CONFIG_SCTP_DBG_OBJCNT is not set +# CONFIG_SCTP_HMAC_NONE is not set +# CONFIG_SCTP_HMAC_SHA1 is not set +CONFIG_SCTP_HMAC_MD5=y +CONFIG_TIPC=m +# CONFIG_TIPC_ADVANCED is not set +# CONFIG_TIPC_DEBUG is not set +CONFIG_ATM=m +CONFIG_ATM_CLIP=m +# CONFIG_ATM_CLIP_NO_ICMP is not set +CONFIG_ATM_LANE=m +CONFIG_ATM_MPOA=m +CONFIG_ATM_BR2684=m +# CONFIG_ATM_BR2684_IPFILTER is not set +CONFIG_BRIDGE=m +CONFIG_VLAN_8021Q=m +# CONFIG_DECNET is not set +CONFIG_LLC=m +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +CONFIG_WAN_ROUTER=m +CONFIG_NET_SCHED=y + +# +# Queueing/Scheduling +# +CONFIG_NET_SCH_CBQ=m +CONFIG_NET_SCH_HTB=m +CONFIG_NET_SCH_HFSC=m +CONFIG_NET_SCH_ATM=m +CONFIG_NET_SCH_PRIO=m +# CONFIG_NET_SCH_RR is not set +CONFIG_NET_SCH_RED=m +CONFIG_NET_SCH_SFQ=m +CONFIG_NET_SCH_TEQL=m +CONFIG_NET_SCH_TBF=m +CONFIG_NET_SCH_GRED=m +CONFIG_NET_SCH_DSMARK=m +CONFIG_NET_SCH_NETEM=m + +# +# Classification +# +CONFIG_NET_CLS=y +# CONFIG_NET_CLS_BASIC is not set +CONFIG_NET_CLS_TCINDEX=m +CONFIG_NET_CLS_ROUTE4=m +CONFIG_NET_CLS_ROUTE=y +CONFIG_NET_CLS_FW=m +CONFIG_NET_CLS_U32=m +# CONFIG_CLS_U32_PERF is not set +# CONFIG_CLS_U32_MARK is not set +CONFIG_NET_CLS_RSVP=m +CONFIG_NET_CLS_RSVP6=m +# CONFIG_NET_CLS_FLOW is not set +# CONFIG_NET_EMATCH is not set +# CONFIG_NET_CLS_ACT is not set +# CONFIG_NET_CLS_IND is not set +CONFIG_NET_SCH_FIFO=y + +# +# Network testing +# +CONFIG_NET_PKTGEN=m +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +CONFIG_FIB_RULES=y + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_CONCAT=y +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +# CONFIG_MTD_CMDLINE_PARTS is not set +# CONFIG_MTD_OF_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +# CONFIG_MTD_CFI_NOSWAP is not set +# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set +CONFIG_MTD_CFI_LE_BYTE_SWAP=y +# CONFIG_MTD_CFI_GEOMETRY is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_AMDSTD=y +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP_OF=y +# CONFIG_MTD_INTEL_VR_NOR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +CONFIG_OF_DEVICE=y +CONFIG_OF_I2C=y +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=m +CONFIG_BLK_DEV_CRYPTOLOOP=m +CONFIG_BLK_DEV_NBD=m +# CONFIG_BLK_DEV_SX8 is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=131072 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_MISC_DEVICES=y +# CONFIG_PHANTOM is not set +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_SGI_IOC4 is not set +# CONFIG_TIFM_CORE is not set +# CONFIG_ENCLOSURE_SERVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +CONFIG_CHR_DEV_ST=y +# CONFIG_CHR_DEV_OSST is not set +CONFIG_BLK_DEV_SR=y +# CONFIG_BLK_DEV_SR_VENDOR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set +# CONFIG_SCSI_ACARD is not set +# CONFIG_SCSI_AACRAID is not set +# CONFIG_SCSI_AIC7XXX is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_AIC79XX is not set +# CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set +# CONFIG_SCSI_ARCMSR is not set +# CONFIG_MEGARAID_NEWGEN is not set +# CONFIG_MEGARAID_LEGACY is not set +# CONFIG_MEGARAID_SAS is not set +# CONFIG_SCSI_HPTIOP is not set +# CONFIG_SCSI_BUSLOGIC is not set +# CONFIG_SCSI_DMX3191D is not set +# CONFIG_SCSI_EATA is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GDTH is not set +# CONFIG_SCSI_IPS is not set +# CONFIG_SCSI_INITIO is not set +# CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_MVSAS is not set +# CONFIG_SCSI_STEX is not set +# CONFIG_SCSI_SYM53C8XX_2 is not set +# CONFIG_SCSI_IPR is not set +# CONFIG_SCSI_QLOGIC_1280 is not set +# CONFIG_SCSI_QLA_FC is not set +# CONFIG_SCSI_QLA_ISCSI is not set +# CONFIG_SCSI_LPFC is not set +# CONFIG_SCSI_DC395x is not set +# CONFIG_SCSI_DC390T is not set +# CONFIG_SCSI_NSP32 is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_SRP is not set +CONFIG_ATA=y +# CONFIG_ATA_NONSTANDARD is not set +CONFIG_SATA_PMP=y +# CONFIG_SATA_AHCI is not set +# CONFIG_SATA_SIL24 is not set +# CONFIG_SATA_FSL is not set +CONFIG_ATA_SFF=y +# CONFIG_SATA_SVW is not set +# CONFIG_ATA_PIIX is not set +# CONFIG_SATA_MV is not set +# CONFIG_SATA_NV is not set +# CONFIG_PDC_ADMA is not set +# CONFIG_SATA_QSTOR is not set +# CONFIG_SATA_PROMISE is not set +# CONFIG_SATA_SX4 is not set +CONFIG_SATA_SIL=y +# CONFIG_SATA_SIS is not set +# CONFIG_SATA_ULI is not set +# CONFIG_SATA_VIA is not set +# CONFIG_SATA_VITESSE is not set +# CONFIG_SATA_INIC162X is not set +# CONFIG_PATA_ALI is not set +# CONFIG_PATA_AMD is not set +# CONFIG_PATA_ARTOP is not set +# CONFIG_PATA_ATIIXP is not set +# CONFIG_PATA_CMD640_PCI is not set +# CONFIG_PATA_CMD64X is not set +# CONFIG_PATA_CS5520 is not set +# CONFIG_PATA_CS5530 is not set +# CONFIG_PATA_CYPRESS is not set +# CONFIG_PATA_EFAR is not set +# CONFIG_ATA_GENERIC is not set +# CONFIG_PATA_HPT366 is not set +# CONFIG_PATA_HPT37X is not set +# CONFIG_PATA_HPT3X2N is not set +# CONFIG_PATA_HPT3X3 is not set +# CONFIG_PATA_IT821X is not set +# CONFIG_PATA_IT8213 is not set +# CONFIG_PATA_JMICRON is not set +# CONFIG_PATA_TRIFLEX is not set +# CONFIG_PATA_MARVELL is not set +# CONFIG_PATA_MPIIX is not set +# CONFIG_PATA_OLDPIIX is not set +# CONFIG_PATA_NETCELL is not set +# CONFIG_PATA_NINJA32 is not set +# CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set +# CONFIG_PATA_OPTI is not set +# CONFIG_PATA_OPTIDMA is not set +# CONFIG_PATA_PDC_OLD is not set +# CONFIG_PATA_RADISYS is not set +# CONFIG_PATA_RZ1000 is not set +# CONFIG_PATA_SC1200 is not set +# CONFIG_PATA_SERVERWORKS is not set +# CONFIG_PATA_PDC2027X is not set +# CONFIG_PATA_SIL680 is not set +# CONFIG_PATA_SIS is not set +# CONFIG_PATA_VIA is not set +# CONFIG_PATA_WINBOND is not set +# CONFIG_PATA_PLATFORM is not set +# CONFIG_PATA_SCH is not set +# CONFIG_MD is not set +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set +# CONFIG_I2O is not set +# CONFIG_MACINTOSH_DRIVERS is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +CONFIG_DUMMY=m +CONFIG_BONDING=m +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +CONFIG_TUN=m +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +CONFIG_MARVELL_PHY=y +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_NET_PCI is not set +# CONFIG_B44 is not set +CONFIG_NETDEV_1000=y +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_E1000E is not set +# CONFIG_E1000E_ENABLED is not set +# CONFIG_IP1000 is not set +# CONFIG_IGB is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_VIA_VELOCITY is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set +CONFIG_GIANFAR=y +# CONFIG_GFAR_NAPI is not set +# CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +CONFIG_ATM_DRIVERS=y +# CONFIG_ATM_DUMMY is not set +# CONFIG_ATM_TCP is not set +# CONFIG_ATM_LANAI is not set +# CONFIG_ATM_ENI is not set +# CONFIG_ATM_FIRESTREAM is not set +# CONFIG_ATM_ZATM is not set +# CONFIG_ATM_NICSTAR is not set +# CONFIG_ATM_IDT77252 is not set +# CONFIG_ATM_AMBASSADOR is not set +# CONFIG_ATM_HORIZON is not set +# CONFIG_ATM_IA is not set +# CONFIG_ATM_FORE200E_MAYBE is not set +# CONFIG_ATM_HE is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +CONFIG_PPP=m +CONFIG_PPP_MULTILINK=y +CONFIG_PPP_FILTER=y +CONFIG_PPP_ASYNC=m +CONFIG_PPP_SYNC_TTY=m +CONFIG_PPP_DEFLATE=m +CONFIG_PPP_BSDCOMP=m +# CONFIG_PPP_MPPE is not set +CONFIG_PPPOE=m +CONFIG_PPPOATM=m +# CONFIG_PPPOL2TP is not set +CONFIG_SLIP=m +CONFIG_SLIP_COMPRESSED=y +CONFIG_SLHC=m +CONFIG_SLIP_SMART=y +CONFIG_SLIP_MODE_SLIP6=y +# CONFIG_NET_FC is not set +CONFIG_NETCONSOLE=y +# CONFIG_NETCONSOLE_DYNAMIC is not set +CONFIG_NETPOLL=y +CONFIG_NETPOLL_TRAP=y +CONFIG_NET_POLL_CONTROLLER=y +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +# CONFIG_SERIAL_8250_PCI is not set +CONFIG_SERIAL_8250_NR_UARTS=2 +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set +# CONFIG_SERIAL_OF_PLATFORM is not set +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y + +# +# I2C Hardware Bus support +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI1563 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_I810 is not set +# CONFIG_I2C_PIIX4 is not set +CONFIG_I2C_MPC=y +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_PROSAVAGE is not set +# CONFIG_I2C_SAVAGE4 is not set +# CONFIG_I2C_SIMTEC is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_TINY_USB is not set +# CONFIG_I2C_VIA is not set +# CONFIG_I2C_VIAPRO is not set +# CONFIG_I2C_VOODOO3 is not set +# CONFIG_I2C_PCA_PLATFORM is not set + +# +# Miscellaneous I2C Chip support +# +CONFIG_DS1682=y +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +# CONFIG_SPI is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_AD7418 is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +CONFIG_SENSORS_LM90=y +CONFIG_SENSORS_LM92=y +# CONFIG_SENSORS_LM93 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_MAX6650 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_SIS5595 is not set +# CONFIG_SENSORS_DME1737 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set +# CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_VIA686A is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_SENSORS_VT8231 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_THERMAL is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +CONFIG_DAB=y +# CONFIG_USB_DABUSB is not set + +# +# Graphics support +# +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +CONFIG_VGA_CONSOLE=y +# CONFIG_VGACON_SOFT_SCROLLBACK is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_USB_HIDINPUT_POWERBOOK is not set +# CONFIG_HID_FF is not set +# CONFIG_USB_HIDDEV is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +# CONFIG_USB_DEVICEFS is not set +# CONFIG_USB_DEVICE_CLASS is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +CONFIG_USB_EHCI_HCD=y +# CONFIG_USB_EHCI_ROOT_HUB_TT is not set +# CONFIG_USB_EHCI_TT_NEWSCHED is not set +# CONFIG_USB_EHCI_FSL is not set +# CONFIG_USB_EHCI_HCD_PPC_OF is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_HCD_PPC_OF is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set +# CONFIG_USB_MON is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_ATM is not set +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +# CONFIG_INFINIBAND is not set +# CONFIG_EDAC is not set +CONFIG_RTC_LIB=m +CONFIG_RTC_CLASS=m + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +# CONFIG_RTC_INTF_PROC is not set +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set + +# +# SPI RTC drivers +# + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_RTC_DRV_PPC is not set +# CONFIG_DMADEVICES is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +CONFIG_EXT2_FS_POSIX_ACL=y +# CONFIG_EXT2_FS_SECURITY is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +CONFIG_EXT3_FS_POSIX_ACL=y +# CONFIG_EXT3_FS_SECURITY is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +CONFIG_FS_POSIX_ACL=y +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS2_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +CONFIG_NFS_V4=y +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_BIND34 is not set +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +CONFIG_CIFS=m +# CONFIG_CIFS_STATS is not set +# CONFIG_CIFS_WEAK_PW_HASH is not set +CONFIG_CIFS_XATTR=y +CONFIG_CIFS_POSIX=y +# CONFIG_CIFS_DEBUG2 is not set +# CONFIG_CIFS_EXPERIMENTAL is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=m +CONFIG_NLS_CODEPAGE_737=m +CONFIG_NLS_CODEPAGE_775=m +CONFIG_NLS_CODEPAGE_850=m +CONFIG_NLS_CODEPAGE_852=m +CONFIG_NLS_CODEPAGE_855=m +CONFIG_NLS_CODEPAGE_857=m +CONFIG_NLS_CODEPAGE_860=m +CONFIG_NLS_CODEPAGE_861=m +CONFIG_NLS_CODEPAGE_862=m +CONFIG_NLS_CODEPAGE_863=m +CONFIG_NLS_CODEPAGE_864=m +CONFIG_NLS_CODEPAGE_865=m +CONFIG_NLS_CODEPAGE_866=m +CONFIG_NLS_CODEPAGE_869=m +CONFIG_NLS_CODEPAGE_936=m +CONFIG_NLS_CODEPAGE_950=m +CONFIG_NLS_CODEPAGE_932=m +CONFIG_NLS_CODEPAGE_949=m +CONFIG_NLS_CODEPAGE_874=m +CONFIG_NLS_ISO8859_8=m +CONFIG_NLS_CODEPAGE_1250=m +CONFIG_NLS_CODEPAGE_1251=m +CONFIG_NLS_ASCII=m +CONFIG_NLS_ISO8859_1=m +CONFIG_NLS_ISO8859_2=m +CONFIG_NLS_ISO8859_3=m +CONFIG_NLS_ISO8859_4=m +CONFIG_NLS_ISO8859_5=m +CONFIG_NLS_ISO8859_6=m +CONFIG_NLS_ISO8859_7=m +CONFIG_NLS_ISO8859_9=m +CONFIG_NLS_ISO8859_13=m +CONFIG_NLS_ISO8859_14=m +CONFIG_NLS_ISO8859_15=m +CONFIG_NLS_KOI8_R=m +CONFIG_NLS_KOI8_U=m +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +CONFIG_CRC_CCITT=m +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=m +CONFIG_ZLIB_INFLATE=m +CONFIG_ZLIB_DEFLATE=m +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_HAVE_LMB=y + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +CONFIG_DEBUGGER=y +# CONFIG_XMON is not set +# CONFIG_IRQSTACKS is not set +# CONFIG_BDI_SWITCH is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +CONFIG_SECURITY=y +CONFIG_SECURITY_NETWORK=y +# CONFIG_SECURITY_NETWORK_XFRM is not set +CONFIG_SECURITY_CAPABILITIES=y +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +# CONFIG_SECURITY_ROOTPLUG is not set +CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0 +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_GF128MUL is not set +CONFIG_CRYPTO_NULL=m +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_AUTHENC=m +CONFIG_CRYPTO_TEST=m + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +CONFIG_CRYPTO_HMAC=y +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +CONFIG_CRYPTO_CRC32C=m +CONFIG_CRYPTO_MD4=m +CONFIG_CRYPTO_MD5=y +CONFIG_CRYPTO_MICHAEL_MIC=m +CONFIG_CRYPTO_SHA1=m +CONFIG_CRYPTO_SHA256=m +CONFIG_CRYPTO_SHA512=m +# CONFIG_CRYPTO_TGR192 is not set +CONFIG_CRYPTO_WP512=m + +# +# Ciphers +# +CONFIG_CRYPTO_AES=m +CONFIG_CRYPTO_ANUBIS=m +CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_BLOWFISH=m +# CONFIG_CRYPTO_CAMELLIA is not set +CONFIG_CRYPTO_CAST5=m +CONFIG_CRYPTO_CAST6=m +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +CONFIG_CRYPTO_KHAZAD=m +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +CONFIG_CRYPTO_SERPENT=m +CONFIG_CRYPTO_TEA=m +CONFIG_CRYPTO_TWOFISH=m +CONFIG_CRYPTO_TWOFISH_COMMON=m + +# +# Compression +# +CONFIG_CRYPTO_DEFLATE=m +# CONFIG_CRYPTO_LZO is not set +# CONFIG_CRYPTO_HW is not set +# CONFIG_PPC_CLOCK is not set +# CONFIG_VIRTUALIZATION is not set -- cgit v1.2.3 From f1eaf16a9e843aa915b86594b60ec6cd66c9eac7 Mon Sep 17 00:00:00 2001 From: Jochen Friedrich Date: Wed, 27 Aug 2008 12:32:25 +0200 Subject: powerpc/cpm1: Fix race condition in CPM1 GPIO library. The CPM1 GPIO library code uses the non thread-safe clrbits32/setbits32 macros. This patch protects them with a spinlock. Based on the CPM2 patch from Laurent Pinchart , commit 639d64456e20cbfc866b18dc03cf9f9babc9c7cd. Signed-off-by: Jochen Friedrich Signed-off-by: Kumar Gala --- arch/powerpc/sysdev/cpm1.c | 74 ++++++++++++++++++++++++++++++++-------------- 1 file changed, 52 insertions(+), 22 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/cpm1.c b/arch/powerpc/sysdev/cpm1.c index 4a04823e842..490473ce810 100644 --- a/arch/powerpc/sysdev/cpm1.c +++ b/arch/powerpc/sysdev/cpm1.c @@ -546,15 +546,11 @@ static int cpm1_gpio16_get(struct gpio_chip *gc, unsigned int gpio) return !!(in_be16(&iop->dat) & pin_mask); } -static void cpm1_gpio16_set(struct gpio_chip *gc, unsigned int gpio, int value) +static void __cpm1_gpio16_set(struct of_mm_gpio_chip *mm_gc, u16 pin_mask, + int value) { - struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc); struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc); struct cpm_ioport16 __iomem *iop = mm_gc->regs; - unsigned long flags; - u16 pin_mask = 1 << (15 - gpio); - - spin_lock_irqsave(&cpm1_gc->lock, flags); if (value) cpm1_gc->cpdata |= pin_mask; @@ -562,6 +558,18 @@ static void cpm1_gpio16_set(struct gpio_chip *gc, unsigned int gpio, int value) cpm1_gc->cpdata &= ~pin_mask; out_be16(&iop->dat, cpm1_gc->cpdata); +} + +static void cpm1_gpio16_set(struct gpio_chip *gc, unsigned int gpio, int value) +{ + struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc); + struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc); + unsigned long flags; + u16 pin_mask = 1 << (15 - gpio); + + spin_lock_irqsave(&cpm1_gc->lock, flags); + + __cpm1_gpio16_set(mm_gc, pin_mask, value); spin_unlock_irqrestore(&cpm1_gc->lock, flags); } @@ -569,14 +577,17 @@ static void cpm1_gpio16_set(struct gpio_chip *gc, unsigned int gpio, int value) static int cpm1_gpio16_dir_out(struct gpio_chip *gc, unsigned int gpio, int val) { struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc); + struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc); struct cpm_ioport16 __iomem *iop = mm_gc->regs; - u16 pin_mask; + unsigned long flags; + u16 pin_mask = 1 << (15 - gpio); - pin_mask = 1 << (15 - gpio); + spin_lock_irqsave(&cpm1_gc->lock, flags); setbits16(&iop->dir, pin_mask); + __cpm1_gpio16_set(mm_gc, pin_mask, val); - cpm1_gpio16_set(gc, gpio, val); + spin_unlock_irqrestore(&cpm1_gc->lock, flags); return 0; } @@ -584,13 +595,17 @@ static int cpm1_gpio16_dir_out(struct gpio_chip *gc, unsigned int gpio, int val) static int cpm1_gpio16_dir_in(struct gpio_chip *gc, unsigned int gpio) { struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc); + struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc); struct cpm_ioport16 __iomem *iop = mm_gc->regs; - u16 pin_mask; + unsigned long flags; + u16 pin_mask = 1 << (15 - gpio); - pin_mask = 1 << (15 - gpio); + spin_lock_irqsave(&cpm1_gc->lock, flags); clrbits16(&iop->dir, pin_mask); + spin_unlock_irqrestore(&cpm1_gc->lock, flags); + return 0; } @@ -655,15 +670,11 @@ static int cpm1_gpio32_get(struct gpio_chip *gc, unsigned int gpio) return !!(in_be32(&iop->dat) & pin_mask); } -static void cpm1_gpio32_set(struct gpio_chip *gc, unsigned int gpio, int value) +static void __cpm1_gpio32_set(struct of_mm_gpio_chip *mm_gc, u32 pin_mask, + int value) { - struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc); struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc); struct cpm_ioport32b __iomem *iop = mm_gc->regs; - unsigned long flags; - u32 pin_mask = 1 << (31 - gpio); - - spin_lock_irqsave(&cpm1_gc->lock, flags); if (value) cpm1_gc->cpdata |= pin_mask; @@ -671,6 +682,18 @@ static void cpm1_gpio32_set(struct gpio_chip *gc, unsigned int gpio, int value) cpm1_gc->cpdata &= ~pin_mask; out_be32(&iop->dat, cpm1_gc->cpdata); +} + +static void cpm1_gpio32_set(struct gpio_chip *gc, unsigned int gpio, int value) +{ + struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc); + struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc); + unsigned long flags; + u32 pin_mask = 1 << (31 - gpio); + + spin_lock_irqsave(&cpm1_gc->lock, flags); + + __cpm1_gpio32_set(mm_gc, pin_mask, value); spin_unlock_irqrestore(&cpm1_gc->lock, flags); } @@ -678,14 +701,17 @@ static void cpm1_gpio32_set(struct gpio_chip *gc, unsigned int gpio, int value) static int cpm1_gpio32_dir_out(struct gpio_chip *gc, unsigned int gpio, int val) { struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc); + struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc); struct cpm_ioport32b __iomem *iop = mm_gc->regs; - u32 pin_mask; + unsigned long flags; + u32 pin_mask = 1 << (31 - gpio); - pin_mask = 1 << (31 - gpio); + spin_lock_irqsave(&cpm1_gc->lock, flags); setbits32(&iop->dir, pin_mask); + __cpm1_gpio32_set(mm_gc, pin_mask, val); - cpm1_gpio32_set(gc, gpio, val); + spin_unlock_irqrestore(&cpm1_gc->lock, flags); return 0; } @@ -693,13 +719,17 @@ static int cpm1_gpio32_dir_out(struct gpio_chip *gc, unsigned int gpio, int val) static int cpm1_gpio32_dir_in(struct gpio_chip *gc, unsigned int gpio) { struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc); + struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc); struct cpm_ioport32b __iomem *iop = mm_gc->regs; - u32 pin_mask; + unsigned long flags; + u32 pin_mask = 1 << (31 - gpio); - pin_mask = 1 << (31 - gpio); + spin_lock_irqsave(&cpm1_gc->lock, flags); clrbits32(&iop->dir, pin_mask); + spin_unlock_irqrestore(&cpm1_gc->lock, flags); + return 0; } -- cgit v1.2.3 From c2fe59444e1827ecd2713a1e6ecfd1ab1fc548ae Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Wed, 6 Aug 2008 11:48:25 -0500 Subject: powerpc: add SSI-to-DMA properties to Freescale MPC8610 HPCD device tree Add the fsl,playback-dma and fsl,capture-dma properties to the Freescale MPC8610 HPCD device tree. These properties connect the SSI nodes to the DMA nodes for the DMA channels that the SSI should use. Also update the ssi.txt documentation. These properties will be needed when the ASoC V2 version of the Freescale MPC8610 device drivers are merged into the mainline. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala --- Documentation/powerpc/dts-bindings/fsl/ssi.txt | 15 +++++++++++++++ arch/powerpc/boot/dts/mpc8610_hpcd.dts | 8 +++++--- 2 files changed, 20 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/Documentation/powerpc/dts-bindings/fsl/ssi.txt b/Documentation/powerpc/dts-bindings/fsl/ssi.txt index d100555d488..5d9841303ca 100644 --- a/Documentation/powerpc/dts-bindings/fsl/ssi.txt +++ b/Documentation/powerpc/dts-bindings/fsl/ssi.txt @@ -24,6 +24,12 @@ Required properties: "rj-master" - r.j., SSI is clock master "ac97-slave" - AC97 mode, SSI is clock slave "ac97-master" - AC97 mode, SSI is clock master +- fsl,playback-dma: phandle to a DMA node for the DMA channel to use for + playback of audio. This is typically dictated by SOC + design. See the notes below. +- fsl,capture-dma: phandle to a DMA node for the DMA channel to use for + capture (recording) of audio. This is typically dictated + by SOC design. See the notes below. Optional properties: - codec-handle : phandle to a 'codec' node that defines an audio @@ -36,3 +42,12 @@ Child 'codec' node required properties: Child 'codec' node optional properties: - clock-frequency : The frequency of the input clock, which typically comes from an on-board dedicated oscillator. + +Notes on fsl,playback-dma and fsl,capture-dma: + +On SOCs that have an SSI, specific DMA channels are hard-wired for playback +and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for +playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for +playback and DMA channel 3 for capture. The developer can choose which +DMA controller to use, but the channels themselves are hard-wired. The +purpose of these two properties is to represent this hardware design. diff --git a/arch/powerpc/boot/dts/mpc8610_hpcd.dts b/arch/powerpc/boot/dts/mpc8610_hpcd.dts index 3b3a1062cb2..0f3a36e0ea6 100644 --- a/arch/powerpc/boot/dts/mpc8610_hpcd.dts +++ b/arch/powerpc/boot/dts/mpc8610_hpcd.dts @@ -207,7 +207,7 @@ reg = <0xe4000 0x100>; }; - i2s@16000 { + ssi@16000 { compatible = "fsl,mpc8610-ssi"; cell-index = <0>; reg = <0x16000 0x100>; @@ -215,6 +215,8 @@ interrupts = <62 2>; fsl,mode = "i2s-slave"; codec-handle = <&cs4270>; + fsl,playback-dma = <&dma00>; + fsl,capture-dma = <&dma01>; }; ssi@16100 { @@ -233,7 +235,7 @@ reg = <0x21300 0x4>; /* DMA general status register */ ranges = <0x0 0x21100 0x200>; - dma-channel@0 { + dma00: dma-channel@0 { compatible = "fsl,mpc8610-dma-channel", "fsl,eloplus-dma-channel"; cell-index = <0>; @@ -241,7 +243,7 @@ interrupt-parent = <&mpic>; interrupts = <20 2>; }; - dma-channel@1 { + dma01: dma-channel@1 { compatible = "fsl,mpc8610-dma-channel", "fsl,eloplus-dma-channel"; cell-index = <1>; -- cgit v1.2.3 From 33a7f122740bd820a029faf450a9a0caa9458426 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Thu, 18 Sep 2008 17:50:42 -0500 Subject: powerpc: Fix build warnings introduced by PMC support on 32-bit arch/powerpc/kernel/sysfs.c:197:7: warning: "CONFIG_6xx" is not defined arch/powerpc/kernel/sysfs.c:141: warning: 'run_on_cpu' defined but not used Signed-off-by: Kumar Gala --- arch/powerpc/kernel/sysfs.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/sysfs.c b/arch/powerpc/kernel/sysfs.c index ef2ad92a417..86a2ffccef2 100644 --- a/arch/powerpc/kernel/sysfs.c +++ b/arch/powerpc/kernel/sysfs.c @@ -134,6 +134,7 @@ void ppc_enable_pmcs(void) } EXPORT_SYMBOL(ppc_enable_pmcs); +#if defined(CONFIG_6xx) || defined(CONFIG_PPC64) /* XXX convert to rusty's on_one_cpu */ static unsigned long run_on_cpu(unsigned long cpu, unsigned long (*func)(unsigned long), @@ -152,6 +153,7 @@ static unsigned long run_on_cpu(unsigned long cpu, return ret; } +#endif #define SYSFS_PMCSETUP(NAME, ADDRESS) \ static unsigned long read_##NAME(unsigned long junk) \ @@ -190,11 +192,11 @@ static ssize_t __used \ * that are implemented on the current processor */ -#ifdef CONFIG_PPC64 +#if defined(CONFIG_PPC64) #define HAS_PPC_PMC_CLASSIC 1 #define HAS_PPC_PMC_IBM 1 #define HAS_PPC_PMC_PA6T 1 -#elif CONFIG_6xx +#elif defined(CONFIG_6xx) #define HAS_PPC_PMC_CLASSIC 1 #define HAS_PPC_PMC_IBM 1 #define HAS_PPC_PMC_G4 1 -- cgit v1.2.3 From b38fd42ff46a4a31dced8533e8a6e549693500b6 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Wed, 16 Jul 2008 16:17:08 -0500 Subject: powerpc/fsl-booke: Fixup 64-bit PTE reading for SMP support We need to create a false data dependency to ensure the loads of the pte are done in the right order. Signed-off-by: Kumar Gala --- arch/powerpc/kernel/head_fsl_booke.S | 26 +++++++++++++++++++++----- 1 file changed, 21 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/head_fsl_booke.S b/arch/powerpc/kernel/head_fsl_booke.S index 3cb52fa0eda..377e0c155c9 100644 --- a/arch/powerpc/kernel/head_fsl_booke.S +++ b/arch/powerpc/kernel/head_fsl_booke.S @@ -579,13 +579,19 @@ interrupt_base: FIND_PTE andc. r13,r13,r11 /* Check permission */ - bne 2f /* Bail if permission mismach */ #ifdef CONFIG_PTE_64BIT - lwz r13, 0(r12) +#ifdef CONFIG_SMP + subf r10,r11,r12 /* create false data dep */ + lwzx r13,r11,r10 /* Get upper pte bits */ +#else + lwz r13,0(r12) /* Get upper pte bits */ +#endif #endif - /* Jump to common tlb load */ + bne 2f /* Bail if permission/valid mismach */ + + /* Jump to common tlb load */ b finish_tlb_load 2: /* The bailout. Restore registers to pre-exception conditions @@ -640,10 +646,20 @@ interrupt_base: FIND_PTE andc. r13,r13,r11 /* Check permission */ + +#ifdef CONFIG_PTE_64BIT +#ifdef CONFIG_SMP + subf r10,r11,r12 /* create false data dep */ + lwzx r13,r11,r10 /* Get upper pte bits */ +#else + lwz r13,0(r12) /* Get upper pte bits */ +#endif +#endif + bne 2f /* Bail if permission mismach */ #ifdef CONFIG_PTE_64BIT - lwz r13, 0(r12) + lwz r13,0(r12) #endif /* Jump to common TLB load point */ @@ -702,7 +718,7 @@ interrupt_base: /* * Both the instruction and data TLB miss get to this * point to load the TLB. - * r10 - EA of fault + * r10 - available to use * r11 - TLB (info from Linux PTE) * r12 - available to use * r13 - upper bits of PTE (if PTE_64BIT) or available to use -- cgit v1.2.3 From 1e16dfc1baa745dd89b95f6e33e4142df6218066 Mon Sep 17 00:00:00 2001 From: Peter Korsgaard Date: Tue, 23 Sep 2008 17:35:38 +0200 Subject: powerpc: gpio driver for mpc8349/8572/8610 and compatible Structured similar to the existing QE GPIO support. Signed-off-by: Peter Korsgaard Acked-by: Anton Vorontsov Signed-off-by: Kumar Gala --- .../powerpc/dts-bindings/fsl/8xxx_gpio.txt | 40 +++++ arch/powerpc/sysdev/Kconfig | 9 ++ arch/powerpc/sysdev/Makefile | 1 + arch/powerpc/sysdev/mpc8xxx_gpio.c | 171 +++++++++++++++++++++ 4 files changed, 221 insertions(+) create mode 100644 Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt create mode 100644 arch/powerpc/sysdev/mpc8xxx_gpio.c (limited to 'arch') diff --git a/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt b/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt new file mode 100644 index 00000000000..d015dcec401 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt @@ -0,0 +1,40 @@ +GPIO controllers on MPC8xxx SoCs + +This is for the non-QE/CPM/GUTs GPIO controllers as found on +8349, 8572, 8610 and compatible. + +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. + +Required properties: +- compatible : "fsl,-gpio" followed by "fsl,mpc8349-gpio" for + 83xx, "fsl,mpc8572-gpio" for 85xx and "fsl,mpc8610-gpio" for 86xx. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + - interrupts : Interrupt mapping for GPIO IRQ (currently unused). + - interrupt-parent : Phandle for the interrupt controller that + services interrupts for this device. +- gpio-controller : Marks the port as GPIO controller. + +Example of gpio-controller nodes for a MPC8347 SoC: + + gpio1: gpio-controller@c00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; + reg = <0xc00 0x100>; + interrupts = <74 0x8>; + interrupt-parent = <&ipic>; + gpio-controller; + }; + + gpio2: gpio-controller@d00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; + reg = <0xd00 0x100>; + interrupts = <75 0x8>; + interrupt-parent = <&ipic>; + gpio-controller; + }; + +See booting-without-of.txt for details of how to specify GPIO +information for devices. diff --git a/arch/powerpc/sysdev/Kconfig b/arch/powerpc/sysdev/Kconfig index 396582835cb..d0e7bb05c3a 100644 --- a/arch/powerpc/sysdev/Kconfig +++ b/arch/powerpc/sysdev/Kconfig @@ -7,6 +7,15 @@ config PPC4xx_PCI_EXPRESS depends on PCI && 4xx default n +config MPC8xxx_GPIO + bool "MPC8xxx GPIO support" + depends on PPC_MPC831x || PPC_MPC834x || PPC_MPC837x || PPC_85xx || PPC_86xx + select GENERIC_GPIO + select ARCH_REQUIRE_GPIOLIB + help + Say Y here if you're going to use hardware that connects to the + MPC831x/834x/837x/8572/8610 GPIOs. + config PPC_MSI_BITMAP bool depends on PCI_MSI diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile index b6c269eb265..55618ba9eff 100644 --- a/arch/powerpc/sysdev/Makefile +++ b/arch/powerpc/sysdev/Makefile @@ -16,6 +16,7 @@ obj-$(CONFIG_FSL_SOC) += fsl_soc.o obj-$(CONFIG_FSL_PCI) += fsl_pci.o $(fsl-msi-obj-y) obj-$(CONFIG_FSL_LBC) += fsl_lbc.o obj-$(CONFIG_FSL_GTM) += fsl_gtm.o +obj-$(CONFIG_MPC8xxx_GPIO) += mpc8xxx_gpio.o obj-$(CONFIG_RAPIDIO) += fsl_rio.o obj-$(CONFIG_TSI108_BRIDGE) += tsi108_pci.o tsi108_dev.o obj-$(CONFIG_QUICC_ENGINE) += qe_lib/ diff --git a/arch/powerpc/sysdev/mpc8xxx_gpio.c b/arch/powerpc/sysdev/mpc8xxx_gpio.c new file mode 100644 index 00000000000..103eace3619 --- /dev/null +++ b/arch/powerpc/sysdev/mpc8xxx_gpio.c @@ -0,0 +1,171 @@ +/* + * GPIOs on MPC8349/8572/8610 and compatible + * + * Copyright (C) 2008 Peter Korsgaard + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include + +#define MPC8XXX_GPIO_PINS 32 + +#define GPIO_DIR 0x00 +#define GPIO_ODR 0x04 +#define GPIO_DAT 0x08 +#define GPIO_IER 0x0c +#define GPIO_IMR 0x10 +#define GPIO_ICR 0x14 + +struct mpc8xxx_gpio_chip { + struct of_mm_gpio_chip mm_gc; + spinlock_t lock; + + /* + * shadowed data register to be able to clear/set output pins in + * open drain mode safely + */ + u32 data; +}; + +static inline u32 mpc8xxx_gpio2mask(unsigned int gpio) +{ + return 1u << (MPC8XXX_GPIO_PINS - 1 - gpio); +} + +static inline struct mpc8xxx_gpio_chip * +to_mpc8xxx_gpio_chip(struct of_mm_gpio_chip *mm) +{ + return container_of(mm, struct mpc8xxx_gpio_chip, mm_gc); +} + +static void mpc8xxx_gpio_save_regs(struct of_mm_gpio_chip *mm) +{ + struct mpc8xxx_gpio_chip *mpc8xxx_gc = to_mpc8xxx_gpio_chip(mm); + + mpc8xxx_gc->data = in_be32(mm->regs + GPIO_DAT); +} + +static int mpc8xxx_gpio_get(struct gpio_chip *gc, unsigned int gpio) +{ + struct of_mm_gpio_chip *mm = to_of_mm_gpio_chip(gc); + + return in_be32(mm->regs + GPIO_DAT) & mpc8xxx_gpio2mask(gpio); +} + +static void mpc8xxx_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val) +{ + struct of_mm_gpio_chip *mm = to_of_mm_gpio_chip(gc); + struct mpc8xxx_gpio_chip *mpc8xxx_gc = to_mpc8xxx_gpio_chip(mm); + unsigned long flags; + + spin_lock_irqsave(&mpc8xxx_gc->lock, flags); + + if (val) + mpc8xxx_gc->data |= mpc8xxx_gpio2mask(gpio); + else + mpc8xxx_gc->data &= ~mpc8xxx_gpio2mask(gpio); + + out_be32(mm->regs + GPIO_DAT, mpc8xxx_gc->data); + + spin_unlock_irqrestore(&mpc8xxx_gc->lock, flags); +} + +static int mpc8xxx_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio) +{ + struct of_mm_gpio_chip *mm = to_of_mm_gpio_chip(gc); + struct mpc8xxx_gpio_chip *mpc8xxx_gc = to_mpc8xxx_gpio_chip(mm); + unsigned long flags; + + spin_lock_irqsave(&mpc8xxx_gc->lock, flags); + + clrbits32(mm->regs + GPIO_DIR, mpc8xxx_gpio2mask(gpio)); + + spin_unlock_irqrestore(&mpc8xxx_gc->lock, flags); + + return 0; +} + +static int mpc8xxx_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val) +{ + struct of_mm_gpio_chip *mm = to_of_mm_gpio_chip(gc); + struct mpc8xxx_gpio_chip *mpc8xxx_gc = to_mpc8xxx_gpio_chip(mm); + unsigned long flags; + + mpc8xxx_gpio_set(gc, gpio, val); + + spin_lock_irqsave(&mpc8xxx_gc->lock, flags); + + setbits32(mm->regs + GPIO_DIR, mpc8xxx_gpio2mask(gpio)); + + spin_unlock_irqrestore(&mpc8xxx_gc->lock, flags); + + return 0; +} + +static void __init mpc8xxx_add_controller(struct device_node *np) +{ + struct mpc8xxx_gpio_chip *mpc8xxx_gc; + struct of_mm_gpio_chip *mm_gc; + struct of_gpio_chip *of_gc; + struct gpio_chip *gc; + int ret; + + mpc8xxx_gc = kzalloc(sizeof(*mpc8xxx_gc), GFP_KERNEL); + if (!mpc8xxx_gc) { + ret = -ENOMEM; + goto err; + } + + spin_lock_init(&mpc8xxx_gc->lock); + + mm_gc = &mpc8xxx_gc->mm_gc; + of_gc = &mm_gc->of_gc; + gc = &of_gc->gc; + + mm_gc->save_regs = mpc8xxx_gpio_save_regs; + of_gc->gpio_cells = 2; + gc->ngpio = MPC8XXX_GPIO_PINS; + gc->direction_input = mpc8xxx_gpio_dir_in; + gc->direction_output = mpc8xxx_gpio_dir_out; + gc->get = mpc8xxx_gpio_get; + gc->set = mpc8xxx_gpio_set; + + ret = of_mm_gpiochip_add(np, mm_gc); + if (ret) + goto err; + + return; + +err: + pr_err("%s: registration failed with status %d\n", + np->full_name, ret); + kfree(mpc8xxx_gc); + + return; +} + +static int __init mpc8xxx_add_gpiochips(void) +{ + struct device_node *np; + + for_each_compatible_node(np, NULL, "fsl,mpc8349-gpio") + mpc8xxx_add_controller(np); + + for_each_compatible_node(np, NULL, "fsl,mpc8572-gpio") + mpc8xxx_add_controller(np); + + for_each_compatible_node(np, NULL, "fsl,mpc8610-gpio") + mpc8xxx_add_controller(np); + + return 0; +} +arch_initcall(mpc8xxx_add_gpiochips); -- cgit v1.2.3 From aeb42762b8f12d2d1833fcc169ba0cd14ea30cc3 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 23 Sep 2008 22:05:10 -0500 Subject: powerpc/83xx: Add missing cell-index to dma-channel device nodes Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/asp834x-redboot.dts | 4 ++++ arch/powerpc/boot/dts/mpc8313erdb.dts | 4 ++++ arch/powerpc/boot/dts/mpc8315erdb.dts | 4 ++++ arch/powerpc/boot/dts/mpc832x_mds.dts | 4 ++++ arch/powerpc/boot/dts/mpc832x_rdb.dts | 4 ++++ arch/powerpc/boot/dts/mpc8349emitx.dts | 4 ++++ arch/powerpc/boot/dts/mpc8349emitxgp.dts | 4 ++++ arch/powerpc/boot/dts/mpc834x_mds.dts | 4 ++++ arch/powerpc/boot/dts/mpc836x_mds.dts | 4 ++++ arch/powerpc/boot/dts/mpc836x_rdk.dts | 4 ++++ arch/powerpc/boot/dts/mpc8377_mds.dts | 4 ++++ arch/powerpc/boot/dts/mpc8377_rdb.dts | 4 ++++ arch/powerpc/boot/dts/mpc8378_mds.dts | 4 ++++ arch/powerpc/boot/dts/mpc8378_rdb.dts | 4 ++++ arch/powerpc/boot/dts/mpc8379_mds.dts | 4 ++++ arch/powerpc/boot/dts/mpc8379_rdb.dts | 4 ++++ arch/powerpc/boot/dts/sbc8349.dts | 4 ++++ 17 files changed, 68 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/asp834x-redboot.dts b/arch/powerpc/boot/dts/asp834x-redboot.dts index 8b1bb0e4190..6235fca445d 100644 --- a/arch/powerpc/boot/dts/asp834x-redboot.dts +++ b/arch/powerpc/boot/dts/asp834x-redboot.dts @@ -130,24 +130,28 @@ dma-channel@0 { compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc8313erdb.dts b/arch/powerpc/boot/dts/mpc8313erdb.dts index 2a94ae0dc8b..539085591e0 100644 --- a/arch/powerpc/boot/dts/mpc8313erdb.dts +++ b/arch/powerpc/boot/dts/mpc8313erdb.dts @@ -176,24 +176,28 @@ dma-channel@0 { compatible = "fsl,mpc8313-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8313-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8313-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8313-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc8315erdb.dts b/arch/powerpc/boot/dts/mpc8315erdb.dts index f704513fb93..94c9b4107a1 100644 --- a/arch/powerpc/boot/dts/mpc8315erdb.dts +++ b/arch/powerpc/boot/dts/mpc8315erdb.dts @@ -144,24 +144,28 @@ dma-channel@0 { compatible = "fsl,mpc8315-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8315-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8315-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8315-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc832x_mds.dts b/arch/powerpc/boot/dts/mpc832x_mds.dts index fbc930410ff..015808ae102 100644 --- a/arch/powerpc/boot/dts/mpc832x_mds.dts +++ b/arch/powerpc/boot/dts/mpc832x_mds.dts @@ -127,24 +127,28 @@ dma-channel@0 { compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc832x_rdb.dts b/arch/powerpc/boot/dts/mpc832x_rdb.dts index b157d1885a2..b5b0ec2eb88 100644 --- a/arch/powerpc/boot/dts/mpc832x_rdb.dts +++ b/arch/powerpc/boot/dts/mpc832x_rdb.dts @@ -105,24 +105,28 @@ dma-channel@0 { compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc8349emitx.dts b/arch/powerpc/boot/dts/mpc8349emitx.dts index 700e076ef3f..1327a61d053 100644 --- a/arch/powerpc/boot/dts/mpc8349emitx.dts +++ b/arch/powerpc/boot/dts/mpc8349emitx.dts @@ -106,24 +106,28 @@ dma-channel@0 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc8349emitxgp.dts b/arch/powerpc/boot/dts/mpc8349emitxgp.dts index cdd3063258e..f70d3a0a6eb 100644 --- a/arch/powerpc/boot/dts/mpc8349emitxgp.dts +++ b/arch/powerpc/boot/dts/mpc8349emitxgp.dts @@ -104,24 +104,28 @@ dma-channel@0 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc834x_mds.dts b/arch/powerpc/boot/dts/mpc834x_mds.dts index 783241c0024..e29739eee35 100644 --- a/arch/powerpc/boot/dts/mpc834x_mds.dts +++ b/arch/powerpc/boot/dts/mpc834x_mds.dts @@ -116,24 +116,28 @@ dma-channel@0 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts index ada8446ab3c..49aec71916e 100644 --- a/arch/powerpc/boot/dts/mpc836x_mds.dts +++ b/arch/powerpc/boot/dts/mpc836x_mds.dts @@ -148,24 +148,28 @@ dma-channel@0 { compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc836x_rdk.dts b/arch/powerpc/boot/dts/mpc836x_rdk.dts index 89c9202f8bd..69c9bd2acd8 100644 --- a/arch/powerpc/boot/dts/mpc836x_rdk.dts +++ b/arch/powerpc/boot/dts/mpc836x_rdk.dts @@ -125,24 +125,28 @@ dma-channel@0 { compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc8377_mds.dts b/arch/powerpc/boot/dts/mpc8377_mds.dts index 432782b6d20..78f0f1124ff 100644 --- a/arch/powerpc/boot/dts/mpc8377_mds.dts +++ b/arch/powerpc/boot/dts/mpc8377_mds.dts @@ -246,24 +246,28 @@ dma-channel@0 { compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <0x47 8>; }; dma-channel@80 { compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <0x47 8>; }; dma-channel@100 { compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <0x47 8>; }; dma-channel@180 { compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <0x47 8>; }; diff --git a/arch/powerpc/boot/dts/mpc8377_rdb.dts b/arch/powerpc/boot/dts/mpc8377_rdb.dts index ed137aa83d5..d46327e8cb6 100644 --- a/arch/powerpc/boot/dts/mpc8377_rdb.dts +++ b/arch/powerpc/boot/dts/mpc8377_rdb.dts @@ -155,24 +155,28 @@ dma-channel@0 { compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc8378_mds.dts b/arch/powerpc/boot/dts/mpc8378_mds.dts index ed32c8ddafe..c44f30f2f08 100644 --- a/arch/powerpc/boot/dts/mpc8378_mds.dts +++ b/arch/powerpc/boot/dts/mpc8378_mds.dts @@ -170,24 +170,28 @@ dma-channel@0 { compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc8378_rdb.dts b/arch/powerpc/boot/dts/mpc8378_rdb.dts index 34a7f2f935e..b3e3bd7d550 100644 --- a/arch/powerpc/boot/dts/mpc8378_rdb.dts +++ b/arch/powerpc/boot/dts/mpc8378_rdb.dts @@ -155,24 +155,28 @@ dma-channel@0 { compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc8379_mds.dts b/arch/powerpc/boot/dts/mpc8379_mds.dts index f4db9ed4a30..653ed47c9a3 100644 --- a/arch/powerpc/boot/dts/mpc8379_mds.dts +++ b/arch/powerpc/boot/dts/mpc8379_mds.dts @@ -170,24 +170,28 @@ dma-channel@0 { compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/mpc8379_rdb.dts b/arch/powerpc/boot/dts/mpc8379_rdb.dts index e4d7030d50e..123c8df6f4f 100644 --- a/arch/powerpc/boot/dts/mpc8379_rdb.dts +++ b/arch/powerpc/boot/dts/mpc8379_rdb.dts @@ -155,24 +155,28 @@ dma-channel@0 { compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; diff --git a/arch/powerpc/boot/dts/sbc8349.dts b/arch/powerpc/boot/dts/sbc8349.dts index 45f789b5670..c7f411f7a9a 100644 --- a/arch/powerpc/boot/dts/sbc8349.dts +++ b/arch/powerpc/boot/dts/sbc8349.dts @@ -107,24 +107,28 @@ dma-channel@0 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0 0x80>; + cell-index = <0>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@80 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x80 0x80>; + cell-index = <1>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@100 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x100 0x80>; + cell-index = <2>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; dma-channel@180 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; reg = <0x180 0x28>; + cell-index = <3>; interrupt-parent = <&ipic>; interrupts = <71 8>; }; -- cgit v1.2.3 From ee1130197e7d64a436dbf7feab0bb77065baf5e8 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 23 Sep 2008 23:32:32 -0500 Subject: powerpc/86xx: Introduce a generic mpc86xx_defconfig Introduced a mpc86xx_defconfig that enables all 86xx boards and moved all other 86xx related defconfigs under configs/86xx to match 83xx and 85xx. Signed-off-by: Kumar Gala --- arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig | 1497 +++++++++++++++++++ arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig | 1666 ++++++++++++++++++++++ arch/powerpc/configs/86xx/sbc8641d_defconfig | 1481 +++++++++++++++++++ arch/powerpc/configs/mpc8610_hpcd_defconfig | 1497 ------------------- arch/powerpc/configs/mpc8641_hpcn_defconfig | 1666 ---------------------- arch/powerpc/configs/mpc86xx_defconfig | 1646 +++++++++++++++++++++ arch/powerpc/configs/sbc8641d_defconfig | 1481 ------------------- 7 files changed, 6290 insertions(+), 4644 deletions(-) create mode 100644 arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig create mode 100644 arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig create mode 100644 arch/powerpc/configs/86xx/sbc8641d_defconfig delete mode 100644 arch/powerpc/configs/mpc8610_hpcd_defconfig delete mode 100644 arch/powerpc/configs/mpc8641_hpcn_defconfig create mode 100644 arch/powerpc/configs/mpc86xx_defconfig delete mode 100644 arch/powerpc/configs/sbc8641d_defconfig (limited to 'arch') diff --git a/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig b/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig new file mode 100644 index 00000000000..1a9990731eb --- /dev/null +++ b/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig @@ -0,0 +1,1497 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.27-rc4 +# Thu Aug 21 00:52:10 2008 +# +# CONFIG_PPC64 is not set + +# +# Processor support +# +CONFIG_6xx=y +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_8xx is not set +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_PPC_FPU=y +CONFIG_ALTIVEC=y +CONFIG_PPC_STD_MMU=y +CONFIG_PPC_STD_MMU_32=y +# CONFIG_PPC_MM_SLICES is not set +# CONFIG_SMP is not set +CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set +CONFIG_IRQ_PER_CPU=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +# CONFIG_ARCH_NO_VIRT_TO_BUS is not set +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_OF=y +CONFIG_PPC_UDBG_16550=y +# CONFIG_GENERIC_TBSYNC is not set +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +CONFIG_DEFAULT_UIMAGE=y +CONFIG_HIBERNATE_32=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +# CONFIG_PPC_DCR_NATIVE is not set +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_GROUP_SCHED=y +# CONFIG_FAIR_GROUP_SCHED is not set +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +CONFIG_KALLSYMS_EXTRA_PASS=y +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +# CONFIG_ELF_CORE is not set +CONFIG_PCSPKR_PLATFORM=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLUB_DEBUG=y +# CONFIG_SLAB is not set +CONFIG_SLUB=y +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +# CONFIG_HAVE_CLK is not set +CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +# CONFIG_IOSCHED_AS is not set +CONFIG_IOSCHED_DEADLINE=y +# CONFIG_IOSCHED_CFQ is not set +# CONFIG_DEFAULT_AS is not set +CONFIG_DEFAULT_DEADLINE=y +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="deadline" +CONFIG_CLASSIC_RCU=y + +# +# Platform support +# +CONFIG_PPC_MULTIPLATFORM=y +CONFIG_CLASSIC32=y +CONFIG_PPC_CHRP=y +# CONFIG_MPC5121_ADS is not set +# CONFIG_MPC5121_GENERIC is not set +# CONFIG_PPC_MPC52xx is not set +CONFIG_PPC_PMAC=y +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PPC_82xx is not set +# CONFIG_PQ2ADS is not set +# CONFIG_PPC_83xx is not set +CONFIG_PPC_86xx=y +# CONFIG_MPC8641_HPCN is not set +# CONFIG_SBC8641D is not set +CONFIG_MPC8610_HPCD=y +CONFIG_MPC8610=y +# CONFIG_EMBEDDED6xx is not set +CONFIG_PPC_NATIVE=y +# CONFIG_UDBG_RTAS_CONSOLE is not set +# CONFIG_IPIC is not set +CONFIG_MPIC=y +# CONFIG_MPIC_WEIRD is not set +CONFIG_PPC_I8259=y +CONFIG_PPC_RTAS=y +# CONFIG_RTAS_ERROR_LOGGING is not set +CONFIG_RTAS_PROC=y +# CONFIG_MMIO_NVRAM is not set +CONFIG_PPC_MPC106=y +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +# CONFIG_PPC601_SYNC_FIX is not set +# CONFIG_TAU is not set +CONFIG_FSL_ULI1575=y + +# +# Kernel options +# +CONFIG_HIGHMEM=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_HZ_100 is not set +# CONFIG_HZ_250 is not set +# CONFIG_HZ_300 is not set +CONFIG_HZ_1000=y +CONFIG_HZ=1000 +CONFIG_SCHED_HRTICK=y +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +# CONFIG_IOMMU_HELPER is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_HAS_WALK_MEMORY=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y +# CONFIG_KEXEC is not set +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_FORCE_MAX_ZONEORDER=12 +CONFIG_PROC_DEVICETREE=y +# CONFIG_CMDLINE_BOOL is not set +CONFIG_EXTRA_TARGETS="" +# CONFIG_PM is not set +# CONFIG_SECCOMP is not set +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +# CONFIG_ISA is not set +CONFIG_ZONE_DMA=y +CONFIG_GENERIC_ISA_DMA=y +CONFIG_PPC_INDIRECT_PCI=y +CONFIG_FSL_SOC=y +CONFIG_FSL_PCI=y +CONFIG_PPC_PCI_CHOICE=y +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_SYSCALL=y +CONFIG_PCIEPORTBUS=y +CONFIG_PCIEAER=y +# CONFIG_PCIEASPM is not set +CONFIG_ARCH_SUPPORTS_MSI=y +# CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y +CONFIG_PCI_DEBUG=y +# CONFIG_PCCARD is not set +# CONFIG_HOTPLUG_PCI is not set +# CONFIG_HAS_RAPIDIO is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_PAGE_OFFSET=0xc0000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_PHYSICAL_START=0x00000000 +CONFIG_TASK_SIZE=0xc0000000 +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=y +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +CONFIG_INET_TUNNEL=y +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +CONFIG_IPV6=y +# CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +# CONFIG_INET6_AH is not set +# CONFIG_INET6_ESP is not set +# CONFIG_INET6_IPCOMP is not set +# CONFIG_IPV6_MIP6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +CONFIG_INET6_XFRM_MODE_TRANSPORT=y +CONFIG_INET6_XFRM_MODE_TUNNEL=y +CONFIG_INET6_XFRM_MODE_BEET=y +# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set +CONFIG_IPV6_SIT=y +CONFIG_IPV6_NDISC_NODETYPE=y +# CONFIG_IPV6_TUNNEL is not set +# CONFIG_IPV6_MULTIPLE_TABLES is not set +# CONFIG_IPV6_MROUTE is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_OF_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CFI_AMDSTD=y +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP_OF=y +# CONFIG_MTD_INTEL_VR_NOR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_CAFE is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +CONFIG_MTD_NAND_FSL_ELBC=y +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +CONFIG_OF_DEVICE=y +CONFIG_OF_I2C=y +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_FD is not set +# CONFIG_MAC_FLOPPY is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=131072 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set +CONFIG_MISC_DEVICES=y +# CONFIG_PHANTOM is not set +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_SGI_IOC4 is not set +# CONFIG_TIFM_CORE is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_HP_ILO is not set +CONFIG_HAVE_IDE=y +CONFIG_IDE=y +# CONFIG_BLK_DEV_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +CONFIG_SCSI_TGT=y +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +CONFIG_CHR_DEV_SG=y +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set +# CONFIG_SCSI_ACARD is not set +# CONFIG_SCSI_AACRAID is not set +# CONFIG_SCSI_AIC7XXX is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_AIC79XX is not set +# CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set +# CONFIG_SCSI_ARCMSR is not set +# CONFIG_MEGARAID_NEWGEN is not set +# CONFIG_MEGARAID_LEGACY is not set +# CONFIG_MEGARAID_SAS is not set +# CONFIG_SCSI_HPTIOP is not set +# CONFIG_SCSI_BUSLOGIC is not set +# CONFIG_SCSI_DMX3191D is not set +# CONFIG_SCSI_EATA is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GDTH is not set +# CONFIG_SCSI_IPS is not set +# CONFIG_SCSI_INITIO is not set +# CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_MVSAS is not set +# CONFIG_SCSI_STEX is not set +# CONFIG_SCSI_SYM53C8XX_2 is not set +# CONFIG_SCSI_IPR is not set +# CONFIG_SCSI_QLOGIC_1280 is not set +# CONFIG_SCSI_QLA_FC is not set +# CONFIG_SCSI_QLA_ISCSI is not set +# CONFIG_SCSI_LPFC is not set +# CONFIG_SCSI_DC395x is not set +# CONFIG_SCSI_DC390T is not set +# CONFIG_SCSI_NSP32 is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_MESH is not set +# CONFIG_SCSI_MAC53C94 is not set +# CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_DH is not set +CONFIG_ATA=y +# CONFIG_ATA_NONSTANDARD is not set +CONFIG_SATA_PMP=y +CONFIG_SATA_AHCI=y +# CONFIG_SATA_SIL24 is not set +# CONFIG_SATA_FSL is not set +CONFIG_ATA_SFF=y +# CONFIG_SATA_SVW is not set +# CONFIG_ATA_PIIX is not set +# CONFIG_SATA_MV is not set +# CONFIG_SATA_NV is not set +# CONFIG_PDC_ADMA is not set +# CONFIG_SATA_QSTOR is not set +# CONFIG_SATA_PROMISE is not set +# CONFIG_SATA_SX4 is not set +# CONFIG_SATA_SIL is not set +# CONFIG_SATA_SIS is not set +# CONFIG_SATA_ULI is not set +# CONFIG_SATA_VIA is not set +# CONFIG_SATA_VITESSE is not set +# CONFIG_SATA_INIC162X is not set +CONFIG_PATA_ALI=y +# CONFIG_PATA_AMD is not set +# CONFIG_PATA_ARTOP is not set +# CONFIG_PATA_ATIIXP is not set +# CONFIG_PATA_CMD640_PCI is not set +# CONFIG_PATA_CMD64X is not set +# CONFIG_PATA_CS5520 is not set +# CONFIG_PATA_CS5530 is not set +# CONFIG_PATA_CYPRESS is not set +# CONFIG_PATA_EFAR is not set +# CONFIG_ATA_GENERIC is not set +# CONFIG_PATA_HPT366 is not set +# CONFIG_PATA_HPT37X is not set +# CONFIG_PATA_HPT3X2N is not set +# CONFIG_PATA_HPT3X3 is not set +# CONFIG_PATA_IT821X is not set +# CONFIG_PATA_IT8213 is not set +# CONFIG_PATA_JMICRON is not set +# CONFIG_PATA_TRIFLEX is not set +# CONFIG_PATA_MARVELL is not set +# CONFIG_PATA_MPIIX is not set +# CONFIG_PATA_OLDPIIX is not set +# CONFIG_PATA_NETCELL is not set +# CONFIG_PATA_NINJA32 is not set +# CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set +# CONFIG_PATA_OPTI is not set +# CONFIG_PATA_OPTIDMA is not set +# CONFIG_PATA_PDC_OLD is not set +# CONFIG_PATA_RADISYS is not set +# CONFIG_PATA_RZ1000 is not set +# CONFIG_PATA_SC1200 is not set +# CONFIG_PATA_SERVERWORKS is not set +# CONFIG_PATA_PDC2027X is not set +# CONFIG_PATA_SIL680 is not set +# CONFIG_PATA_SIS is not set +# CONFIG_PATA_VIA is not set +# CONFIG_PATA_WINBOND is not set +# CONFIG_PATA_PLATFORM is not set +# CONFIG_PATA_SCH is not set +# CONFIG_MD is not set +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# Enable only one of the two stacks, unless you know what you are doing +# +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set +# CONFIG_I2O is not set +# CONFIG_MACINTOSH_DRIVERS is not set +CONFIG_NETDEVICES=y +CONFIG_DUMMY=y +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y +# CONFIG_MII is not set +# CONFIG_MACE is not set +# CONFIG_BMAC is not set +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set +CONFIG_NET_TULIP=y +# CONFIG_DE2104X is not set +# CONFIG_TULIP is not set +# CONFIG_DE4X5 is not set +# CONFIG_WINBOND_840 is not set +# CONFIG_DM9102 is not set +CONFIG_ULI526X=y +# CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_NET_PCI is not set +# CONFIG_B44 is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NET_FC is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_I8042=y +CONFIG_SERIO_SERPORT=y +# CONFIG_SERIO_PCIPS2 is not set +CONFIG_SERIO_LIBPS2=y +# CONFIG_SERIO_RAW is not set +# CONFIG_SERIO_XILINX_XPS_PS2 is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y +CONFIG_SERIAL_8250_NR_UARTS=2 +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_MANY_PORTS=y +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_8250_DETECT_IRQ=y +CONFIG_SERIAL_8250_RSA=y + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_PMACZILOG is not set +# CONFIG_SERIAL_JSM is not set +# CONFIG_SERIAL_OF_PLATFORM is not set +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set +# CONFIG_BRIQ_PANEL is not set +# CONFIG_HVC_RTAS is not set +# CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_NVRAM is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +# CONFIG_I2C_CHARDEV is not set +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# PC SMBus host controller drivers +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI1563 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_ISCH is not set +# CONFIG_I2C_PIIX4 is not set +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_VIA is not set +# CONFIG_I2C_VIAPRO is not set + +# +# Mac SMBus host controller drivers +# +# CONFIG_I2C_HYDRA is not set +CONFIG_I2C_POWERMAC=y + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_MPC=y +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set + +# +# Graphics adapter I2C/DDC channel drivers +# +# CONFIG_I2C_VOODOO3 is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_AT24 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +# CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +CONFIG_DAB=y + +# +# Graphics support +# +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_CIRRUS is not set +# CONFIG_FB_PM2 is not set +# CONFIG_FB_CYBER2000 is not set +# CONFIG_FB_OF is not set +# CONFIG_FB_CONTROL is not set +# CONFIG_FB_PLATINUM is not set +# CONFIG_FB_VALKYRIE is not set +# CONFIG_FB_CT65550 is not set +# CONFIG_FB_ASILIANT is not set +# CONFIG_FB_IMSTT is not set +# CONFIG_FB_VGA16 is not set +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_NVIDIA is not set +# CONFIG_FB_RIVA is not set +# CONFIG_FB_MATROX is not set +# CONFIG_FB_RADEON is not set +# CONFIG_FB_ATY128 is not set +# CONFIG_FB_ATY is not set +# CONFIG_FB_S3 is not set +# CONFIG_FB_SAVAGE is not set +# CONFIG_FB_SIS is not set +# CONFIG_FB_NEOMAGIC is not set +# CONFIG_FB_KYRO is not set +# CONFIG_FB_3DFX is not set +# CONFIG_FB_VOODOO1 is not set +# CONFIG_FB_VT8623 is not set +# CONFIG_FB_TRIDENT is not set +# CONFIG_FB_ARK is not set +# CONFIG_FB_PM3 is not set +# CONFIG_FB_CARMINE is not set +CONFIG_FB_FSL_DIU=y +# CONFIG_FB_IBM_GXT4500 is not set +# CONFIG_FB_VIRTUAL is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +CONFIG_VGA_CONSOLE=y +# CONFIG_VGACON_SOFT_SCROLLBACK is not set +CONFIG_DUMMY_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE is not set +# CONFIG_LOGO is not set +CONFIG_SOUND=y +CONFIG_SND=y +CONFIG_SND_TIMER=y +CONFIG_SND_PCM=y +# CONFIG_SND_SEQUENCER is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=y +CONFIG_SND_PCM_OSS=y +CONFIG_SND_PCM_OSS_PLUGINS=y +# CONFIG_SND_DYNAMIC_MINORS is not set +# CONFIG_SND_SUPPORT_OLD_API is not set +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +CONFIG_SND_PCI=y +# CONFIG_SND_AD1889 is not set +# CONFIG_SND_ALS300 is not set +# CONFIG_SND_ALS4000 is not set +# CONFIG_SND_ALI5451 is not set +# CONFIG_SND_ATIIXP is not set +# CONFIG_SND_ATIIXP_MODEM is not set +# CONFIG_SND_AU8810 is not set +# CONFIG_SND_AU8820 is not set +# CONFIG_SND_AU8830 is not set +# CONFIG_SND_AW2 is not set +# CONFIG_SND_AZT3328 is not set +# CONFIG_SND_BT87X is not set +# CONFIG_SND_CA0106 is not set +# CONFIG_SND_CMIPCI is not set +# CONFIG_SND_OXYGEN is not set +# CONFIG_SND_CS4281 is not set +# CONFIG_SND_CS46XX is not set +# CONFIG_SND_CS5530 is not set +# CONFIG_SND_DARLA20 is not set +# CONFIG_SND_GINA20 is not set +# CONFIG_SND_LAYLA20 is not set +# CONFIG_SND_DARLA24 is not set +# CONFIG_SND_GINA24 is not set +# CONFIG_SND_LAYLA24 is not set +# CONFIG_SND_MONA is not set +# CONFIG_SND_MIA is not set +# CONFIG_SND_ECHO3G is not set +# CONFIG_SND_INDIGO is not set +# CONFIG_SND_INDIGOIO is not set +# CONFIG_SND_INDIGODJ is not set +# CONFIG_SND_EMU10K1 is not set +# CONFIG_SND_EMU10K1X is not set +# CONFIG_SND_ENS1370 is not set +# CONFIG_SND_ENS1371 is not set +# CONFIG_SND_ES1938 is not set +# CONFIG_SND_ES1968 is not set +# CONFIG_SND_FM801 is not set +# CONFIG_SND_HDA_INTEL is not set +# CONFIG_SND_HDSP is not set +# CONFIG_SND_HDSPM is not set +# CONFIG_SND_HIFIER is not set +# CONFIG_SND_ICE1712 is not set +# CONFIG_SND_ICE1724 is not set +# CONFIG_SND_INTEL8X0 is not set +# CONFIG_SND_INTEL8X0M is not set +# CONFIG_SND_KORG1212 is not set +# CONFIG_SND_MAESTRO3 is not set +# CONFIG_SND_MIXART is not set +# CONFIG_SND_NM256 is not set +# CONFIG_SND_PCXHR is not set +# CONFIG_SND_RIPTIDE is not set +# CONFIG_SND_RME32 is not set +# CONFIG_SND_RME96 is not set +# CONFIG_SND_RME9652 is not set +# CONFIG_SND_SONICVIBES is not set +# CONFIG_SND_TRIDENT is not set +# CONFIG_SND_VIA82XX is not set +# CONFIG_SND_VIA82XX_MODEM is not set +# CONFIG_SND_VIRTUOSO is not set +# CONFIG_SND_VX222 is not set +# CONFIG_SND_YMFPCI is not set +CONFIG_SND_PPC=y +# CONFIG_SND_POWERMAC is not set +# CONFIG_SND_AOA is not set +CONFIG_SND_SOC=y +CONFIG_SND_SOC_MPC8610=y +CONFIG_SND_SOC_MPC8610_HPCD=y +CONFIG_SND_SOC_CS4270=y +CONFIG_SND_SOC_CS4270_VD33_ERRATA=y +# CONFIG_SOUND_PRIME is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +# CONFIG_USB is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set + +# +# Enable Host or Gadget support to see Inventra options +# + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +# CONFIG_INFINIBAND is not set +# CONFIG_EDAC is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set + +# +# SPI RTC drivers +# + +# +# Platform RTC drivers +# +CONFIG_RTC_DRV_CMOS=y +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_RTC_DRV_PPC is not set +# CONFIG_DMADEVICES is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_DNOTIFY is not set +# CONFIG_INOTIFY is not set +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS2_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +CONFIG_ROOT_NFS=y +CONFIG_NFSD=y +# CONFIG_NFSD_V3 is not set +# CONFIG_NFSD_V4 is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_EXPORTFS=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +CONFIG_LDM_PARTITION=y +# CONFIG_LDM_DEBUG is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_HAVE_LMB=y + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +CONFIG_DEBUG_SHIRQ=y +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_SLUB_STATS is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_HIGHMEM is not set +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_HAVE_FTRACE=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +# CONFIG_FTRACE is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_XMON is not set +# CONFIG_IRQSTACKS is not set +# CONFIG_BDI_SWITCH is not set +# CONFIG_BOOTX_TEXT is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +# CONFIG_CRYPTO_MANAGER is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +# CONFIG_CRYPTO_CBC is not set +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y +# CONFIG_CRYPTO_DEV_HIFN_795X is not set +# CONFIG_CRYPTO_DEV_TALITOS is not set +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y +# CONFIG_VIRTUALIZATION is not set diff --git a/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig b/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig new file mode 100644 index 00000000000..ea09be31b6e --- /dev/null +++ b/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig @@ -0,0 +1,1666 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.27-rc4 +# Thu Aug 21 00:52:11 2008 +# +# CONFIG_PPC64 is not set + +# +# Processor support +# +CONFIG_6xx=y +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_8xx is not set +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_PPC_FPU=y +CONFIG_ALTIVEC=y +CONFIG_PPC_STD_MMU=y +CONFIG_PPC_STD_MMU_32=y +# CONFIG_PPC_MM_SLICES is not set +CONFIG_SMP=y +CONFIG_NR_CPUS=2 +CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set +CONFIG_IRQ_PER_CPU=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +# CONFIG_ARCH_NO_VIRT_TO_BUS is not set +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_OF=y +CONFIG_PPC_UDBG_16550=y +CONFIG_GENERIC_TBSYNC=y +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +CONFIG_DEFAULT_UIMAGE=y +# CONFIG_PPC_DCR_NATIVE is not set +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +CONFIG_BSD_PROCESS_ACCT=y +# CONFIG_BSD_PROCESS_ACCT_V3 is not set +# CONFIG_TASKSTATS is not set +CONFIG_AUDIT=y +# CONFIG_AUDITSYSCALL is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_GROUP_SCHED=y +# CONFIG_FAIR_GROUP_SCHED is not set +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +CONFIG_KALLSYMS_ALL=y +CONFIG_KALLSYMS_EXTRA_PASS=y +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_PCSPKR_PLATFORM=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLUB_DEBUG=y +# CONFIG_SLAB is not set +CONFIG_SLUB=y +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_USE_GENERIC_SMP_HELPERS=y +# CONFIG_HAVE_CLK is not set +CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MODVERSIONS=y +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_STOP_MACHINE=y +CONFIG_BLOCK=y +CONFIG_LBD=y +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +CONFIG_DEFAULT_CFQ=y +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y + +# +# Platform support +# +CONFIG_PPC_MULTIPLATFORM=y +CONFIG_CLASSIC32=y +CONFIG_PPC_CHRP=y +# CONFIG_MPC5121_ADS is not set +# CONFIG_MPC5121_GENERIC is not set +# CONFIG_PPC_MPC52xx is not set +CONFIG_PPC_PMAC=y +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PPC_82xx is not set +# CONFIG_PQ2ADS is not set +# CONFIG_PPC_83xx is not set +CONFIG_PPC_86xx=y +CONFIG_MPC8641_HPCN=y +# CONFIG_SBC8641D is not set +# CONFIG_MPC8610_HPCD is not set +CONFIG_MPC8641=y +CONFIG_PPC_NATIVE=y +# CONFIG_UDBG_RTAS_CONSOLE is not set +# CONFIG_IPIC is not set +CONFIG_MPIC=y +# CONFIG_MPIC_WEIRD is not set +CONFIG_PPC_I8259=y +CONFIG_PPC_RTAS=y +# CONFIG_RTAS_ERROR_LOGGING is not set +CONFIG_RTAS_PROC=y +# CONFIG_MMIO_NVRAM is not set +CONFIG_PPC_MPC106=y +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +# CONFIG_PPC601_SYNC_FIX is not set +# CONFIG_TAU is not set +CONFIG_FSL_ULI1575=y + +# +# Kernel options +# +CONFIG_HIGHMEM=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_HZ_100 is not set +# CONFIG_HZ_250 is not set +# CONFIG_HZ_300 is not set +CONFIG_HZ_1000=y +CONFIG_HZ=1000 +CONFIG_SCHED_HRTICK=y +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +CONFIG_BINFMT_MISC=m +# CONFIG_IOMMU_HELPER is not set +# CONFIG_HOTPLUG_CPU is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_HAS_WALK_MEMORY=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y +# CONFIG_KEXEC is not set +# CONFIG_IRQ_ALL_CPUS is not set +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_FORCE_MAX_ZONEORDER=11 +CONFIG_PROC_DEVICETREE=y +# CONFIG_CMDLINE_BOOL is not set +CONFIG_EXTRA_TARGETS="" +# CONFIG_PM is not set +CONFIG_SECCOMP=y +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +# CONFIG_ISA is not set +CONFIG_ZONE_DMA=y +CONFIG_GENERIC_ISA_DMA=y +CONFIG_PPC_INDIRECT_PCI=y +CONFIG_FSL_SOC=y +CONFIG_FSL_PCI=y +CONFIG_PPC_PCI_CHOICE=y +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_SYSCALL=y +# CONFIG_PCIEPORTBUS is not set +CONFIG_ARCH_SUPPORTS_MSI=y +# CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y +# CONFIG_PCI_DEBUG is not set +# CONFIG_PCCARD is not set +# CONFIG_HOTPLUG_PCI is not set +CONFIG_HAS_RAPIDIO=y +# CONFIG_RAPIDIO is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_PAGE_OFFSET=0xc0000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_PHYSICAL_START=0x00000000 +CONFIG_TASK_SIZE=0xc0000000 +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=y +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +CONFIG_NET_KEY=m +# CONFIG_NET_KEY_MIGRATE is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_ADVANCED_ROUTER=y +CONFIG_ASK_IP_FIB_HASH=y +# CONFIG_IP_FIB_TRIE is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_MULTIPLE_TABLES=y +CONFIG_IP_ROUTE_MULTIPATH=y +CONFIG_IP_ROUTE_VERBOSE=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +CONFIG_NET_IPIP=y +CONFIG_NET_IPGRE=y +CONFIG_NET_IPGRE_BROADCAST=y +CONFIG_IP_MROUTE=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +CONFIG_ARPD=y +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +CONFIG_INET_TUNNEL=y +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +CONFIG_IPV6=y +# CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +# CONFIG_INET6_AH is not set +# CONFIG_INET6_ESP is not set +# CONFIG_INET6_IPCOMP is not set +# CONFIG_IPV6_MIP6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +CONFIG_INET6_XFRM_MODE_TRANSPORT=y +CONFIG_INET6_XFRM_MODE_TUNNEL=y +CONFIG_INET6_XFRM_MODE_BEET=y +# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set +CONFIG_IPV6_SIT=y +CONFIG_IPV6_NDISC_NODETYPE=y +# CONFIG_IPV6_TUNNEL is not set +# CONFIG_IPV6_MULTIPLE_TABLES is not set +# CONFIG_IPV6_MROUTE is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +CONFIG_IP_SCTP=m +# CONFIG_SCTP_DBG_MSG is not set +# CONFIG_SCTP_DBG_OBJCNT is not set +# CONFIG_SCTP_HMAC_NONE is not set +# CONFIG_SCTP_HMAC_SHA1 is not set +CONFIG_SCTP_HMAC_MD5=y +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +CONFIG_FIB_RULES=y + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +# CONFIG_MTD is not set +CONFIG_OF_DEVICE=y +CONFIG_OF_I2C=y +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_FD is not set +# CONFIG_MAC_FLOPPY is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +CONFIG_BLK_DEV_NBD=y +# CONFIG_BLK_DEV_SX8 is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=131072 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set +CONFIG_MISC_DEVICES=y +# CONFIG_PHANTOM is not set +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_SGI_IOC4 is not set +# CONFIG_TIFM_CORE is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_HP_ILO is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +CONFIG_CHR_DEV_ST=y +# CONFIG_CHR_DEV_OSST is not set +CONFIG_BLK_DEV_SR=y +# CONFIG_BLK_DEV_SR_VENDOR is not set +CONFIG_CHR_DEV_SG=y +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +# CONFIG_SCSI_CONSTANTS is not set +CONFIG_SCSI_LOGGING=y +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set +# CONFIG_SCSI_ACARD is not set +# CONFIG_SCSI_AACRAID is not set +# CONFIG_SCSI_AIC7XXX is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_AIC79XX is not set +# CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set +# CONFIG_SCSI_ARCMSR is not set +# CONFIG_MEGARAID_NEWGEN is not set +# CONFIG_MEGARAID_LEGACY is not set +# CONFIG_MEGARAID_SAS is not set +# CONFIG_SCSI_HPTIOP is not set +# CONFIG_SCSI_BUSLOGIC is not set +# CONFIG_SCSI_DMX3191D is not set +# CONFIG_SCSI_EATA is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GDTH is not set +# CONFIG_SCSI_IPS is not set +# CONFIG_SCSI_INITIO is not set +# CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_MVSAS is not set +# CONFIG_SCSI_STEX is not set +# CONFIG_SCSI_SYM53C8XX_2 is not set +# CONFIG_SCSI_IPR is not set +# CONFIG_SCSI_QLOGIC_1280 is not set +# CONFIG_SCSI_QLA_FC is not set +# CONFIG_SCSI_QLA_ISCSI is not set +# CONFIG_SCSI_LPFC is not set +# CONFIG_SCSI_DC395x is not set +# CONFIG_SCSI_DC390T is not set +# CONFIG_SCSI_NSP32 is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_MESH is not set +# CONFIG_SCSI_MAC53C94 is not set +# CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_DH is not set +CONFIG_ATA=y +# CONFIG_ATA_NONSTANDARD is not set +CONFIG_SATA_PMP=y +CONFIG_SATA_AHCI=y +# CONFIG_SATA_SIL24 is not set +# CONFIG_SATA_FSL is not set +CONFIG_ATA_SFF=y +# CONFIG_SATA_SVW is not set +# CONFIG_ATA_PIIX is not set +# CONFIG_SATA_MV is not set +# CONFIG_SATA_NV is not set +# CONFIG_PDC_ADMA is not set +# CONFIG_SATA_QSTOR is not set +# CONFIG_SATA_PROMISE is not set +# CONFIG_SATA_SX4 is not set +# CONFIG_SATA_SIL is not set +# CONFIG_SATA_SIS is not set +# CONFIG_SATA_ULI is not set +# CONFIG_SATA_VIA is not set +# CONFIG_SATA_VITESSE is not set +# CONFIG_SATA_INIC162X is not set +CONFIG_PATA_ALI=y +# CONFIG_PATA_AMD is not set +# CONFIG_PATA_ARTOP is not set +# CONFIG_PATA_ATIIXP is not set +# CONFIG_PATA_CMD640_PCI is not set +# CONFIG_PATA_CMD64X is not set +# CONFIG_PATA_CS5520 is not set +# CONFIG_PATA_CS5530 is not set +# CONFIG_PATA_CYPRESS is not set +# CONFIG_PATA_EFAR is not set +# CONFIG_ATA_GENERIC is not set +# CONFIG_PATA_HPT366 is not set +# CONFIG_PATA_HPT37X is not set +# CONFIG_PATA_HPT3X2N is not set +# CONFIG_PATA_HPT3X3 is not set +# CONFIG_PATA_IT821X is not set +# CONFIG_PATA_IT8213 is not set +# CONFIG_PATA_JMICRON is not set +# CONFIG_PATA_TRIFLEX is not set +# CONFIG_PATA_MARVELL is not set +# CONFIG_PATA_MPIIX is not set +# CONFIG_PATA_OLDPIIX is not set +# CONFIG_PATA_NETCELL is not set +# CONFIG_PATA_NINJA32 is not set +# CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set +# CONFIG_PATA_OPTI is not set +# CONFIG_PATA_OPTIDMA is not set +# CONFIG_PATA_PDC_OLD is not set +# CONFIG_PATA_RADISYS is not set +# CONFIG_PATA_RZ1000 is not set +# CONFIG_PATA_SC1200 is not set +# CONFIG_PATA_SERVERWORKS is not set +# CONFIG_PATA_PDC2027X is not set +# CONFIG_PATA_SIL680 is not set +# CONFIG_PATA_SIS is not set +# CONFIG_PATA_VIA is not set +# CONFIG_PATA_WINBOND is not set +# CONFIG_PATA_PLATFORM is not set +# CONFIG_PATA_SCH is not set +# CONFIG_MD is not set +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# Enable only one of the two stacks, unless you know what you are doing +# +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set +# CONFIG_I2O is not set +# CONFIG_MACINTOSH_DRIVERS is not set +CONFIG_NETDEVICES=y +CONFIG_DUMMY=y +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +CONFIG_VITESSE_PHY=y +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_MACE is not set +# CONFIG_BMAC is not set +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_NET_PCI is not set +# CONFIG_B44 is not set +CONFIG_NETDEV_1000=y +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_E1000E is not set +# CONFIG_IP1000 is not set +# CONFIG_IGB is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_VIA_VELOCITY is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set +CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set +# CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set +# CONFIG_ATL1E is not set +CONFIG_NETDEV_10000=y +# CONFIG_CHELSIO_T1 is not set +# CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set +# CONFIG_IXGB is not set +# CONFIG_S2IO is not set +# CONFIG_MYRI10GE is not set +# CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set +# CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set +# CONFIG_BNX2X is not set +# CONFIG_SFC is not set +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NET_FC is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_I8042=y +CONFIG_SERIO_SERPORT=y +# CONFIG_SERIO_PCIPS2 is not set +CONFIG_SERIO_LIBPS2=y +# CONFIG_SERIO_RAW is not set +# CONFIG_SERIO_XILINX_XPS_PS2 is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y +CONFIG_SERIAL_8250_NR_UARTS=2 +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_MANY_PORTS=y +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_8250_DETECT_IRQ=y +CONFIG_SERIAL_8250_RSA=y + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_PMACZILOG is not set +# CONFIG_SERIAL_JSM is not set +# CONFIG_SERIAL_OF_PLATFORM is not set +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_BRIQ_PANEL is not set +# CONFIG_HVC_RTAS is not set +# CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +CONFIG_NVRAM=y +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +# CONFIG_I2C_CHARDEV is not set +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# PC SMBus host controller drivers +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI1563 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_ISCH is not set +# CONFIG_I2C_PIIX4 is not set +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_VIA is not set +# CONFIG_I2C_VIAPRO is not set + +# +# Mac SMBus host controller drivers +# +# CONFIG_I2C_HYDRA is not set +CONFIG_I2C_POWERMAC=y + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_MPC=y +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Graphics adapter I2C/DDC channel drivers +# +# CONFIG_I2C_VOODOO3 is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_AT24 is not set +CONFIG_SENSORS_EEPROM=y +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +# CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +CONFIG_DVB_CORE=m +CONFIG_VIDEO_MEDIA=m + +# +# Multimedia drivers +# +# CONFIG_MEDIA_ATTACH is not set +CONFIG_MEDIA_TUNER=m +# CONFIG_MEDIA_TUNER_CUSTOMIZE is not set +CONFIG_MEDIA_TUNER_SIMPLE=m +CONFIG_MEDIA_TUNER_TDA8290=m +CONFIG_MEDIA_TUNER_TDA9887=m +CONFIG_MEDIA_TUNER_TEA5761=m +CONFIG_MEDIA_TUNER_TEA5767=m +CONFIG_MEDIA_TUNER_MT20XX=m +CONFIG_MEDIA_TUNER_XC2028=m +CONFIG_MEDIA_TUNER_XC5000=m +CONFIG_DVB_CAPTURE_DRIVERS=y + +# +# Supported SAA7146 based PCI Adapters +# +# CONFIG_TTPCI_EEPROM is not set +# CONFIG_DVB_BUDGET_CORE is not set + +# +# Supported USB Adapters +# +# CONFIG_DVB_USB is not set +# CONFIG_DVB_TTUSB_BUDGET is not set +# CONFIG_DVB_TTUSB_DEC is not set +# CONFIG_DVB_CINERGYT2 is not set +# CONFIG_DVB_SIANO_SMS1XXX is not set + +# +# Supported FlexCopII (B2C2) Adapters +# +# CONFIG_DVB_B2C2_FLEXCOP is not set + +# +# Supported BT878 Adapters +# + +# +# Supported Pluto2 Adapters +# +# CONFIG_DVB_PLUTO2 is not set + +# +# Supported DVB Frontends +# + +# +# Customise DVB Frontends +# +# CONFIG_DVB_FE_CUSTOMISE is not set + +# +# DVB-S (satellite) frontends +# +# CONFIG_DVB_CX24110 is not set +# CONFIG_DVB_CX24123 is not set +# CONFIG_DVB_MT312 is not set +# CONFIG_DVB_S5H1420 is not set +# CONFIG_DVB_STV0299 is not set +# CONFIG_DVB_TDA8083 is not set +# CONFIG_DVB_TDA10086 is not set +# CONFIG_DVB_VES1X93 is not set +# CONFIG_DVB_TUNER_ITD1000 is not set +# CONFIG_DVB_TDA826X is not set +# CONFIG_DVB_TUA6100 is not set + +# +# DVB-T (terrestrial) frontends +# +# CONFIG_DVB_SP8870 is not set +# CONFIG_DVB_SP887X is not set +# CONFIG_DVB_CX22700 is not set +# CONFIG_DVB_CX22702 is not set +# CONFIG_DVB_DRX397XD is not set +# CONFIG_DVB_L64781 is not set +# CONFIG_DVB_TDA1004X is not set +# CONFIG_DVB_NXT6000 is not set +# CONFIG_DVB_MT352 is not set +# CONFIG_DVB_ZL10353 is not set +# CONFIG_DVB_DIB3000MB is not set +# CONFIG_DVB_DIB3000MC is not set +# CONFIG_DVB_DIB7000M is not set +# CONFIG_DVB_DIB7000P is not set +# CONFIG_DVB_TDA10048 is not set + +# +# DVB-C (cable) frontends +# +# CONFIG_DVB_VES1820 is not set +# CONFIG_DVB_TDA10021 is not set +# CONFIG_DVB_TDA10023 is not set +# CONFIG_DVB_STV0297 is not set + +# +# ATSC (North American/Korean Terrestrial/Cable DTV) frontends +# +# CONFIG_DVB_NXT200X is not set +# CONFIG_DVB_OR51211 is not set +# CONFIG_DVB_OR51132 is not set +# CONFIG_DVB_BCM3510 is not set +# CONFIG_DVB_LGDT330X is not set +# CONFIG_DVB_S5H1409 is not set +# CONFIG_DVB_AU8522 is not set +# CONFIG_DVB_S5H1411 is not set + +# +# Digital terrestrial only tuners/PLL +# +# CONFIG_DVB_PLL is not set +# CONFIG_DVB_TUNER_DIB0070 is not set + +# +# SEC control devices for DVB-S +# +# CONFIG_DVB_LNBP21 is not set +# CONFIG_DVB_ISL6405 is not set +# CONFIG_DVB_ISL6421 is not set +CONFIG_DAB=y +# CONFIG_USB_DABUSB is not set + +# +# Graphics support +# +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +CONFIG_VGA_CONSOLE=y +# CONFIG_VGACON_SOFT_SCROLLBACK is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_SOUND=y +CONFIG_SND=y +CONFIG_SND_TIMER=y +CONFIG_SND_PCM=y +# CONFIG_SND_SEQUENCER is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=y +CONFIG_SND_PCM_OSS=y +CONFIG_SND_PCM_OSS_PLUGINS=y +# CONFIG_SND_DYNAMIC_MINORS is not set +# CONFIG_SND_SUPPORT_OLD_API is not set +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +CONFIG_SND_VMASTER=y +CONFIG_SND_AC97_CODEC=y +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +# CONFIG_SND_AC97_POWER_SAVE is not set +CONFIG_SND_PCI=y +# CONFIG_SND_AD1889 is not set +# CONFIG_SND_ALS300 is not set +# CONFIG_SND_ALS4000 is not set +# CONFIG_SND_ALI5451 is not set +# CONFIG_SND_ATIIXP is not set +# CONFIG_SND_ATIIXP_MODEM is not set +# CONFIG_SND_AU8810 is not set +# CONFIG_SND_AU8820 is not set +# CONFIG_SND_AU8830 is not set +# CONFIG_SND_AW2 is not set +# CONFIG_SND_AZT3328 is not set +# CONFIG_SND_BT87X is not set +# CONFIG_SND_CA0106 is not set +# CONFIG_SND_CMIPCI is not set +# CONFIG_SND_OXYGEN is not set +# CONFIG_SND_CS4281 is not set +# CONFIG_SND_CS46XX is not set +# CONFIG_SND_CS5530 is not set +# CONFIG_SND_DARLA20 is not set +# CONFIG_SND_GINA20 is not set +# CONFIG_SND_LAYLA20 is not set +# CONFIG_SND_DARLA24 is not set +# CONFIG_SND_GINA24 is not set +# CONFIG_SND_LAYLA24 is not set +# CONFIG_SND_MONA is not set +# CONFIG_SND_MIA is not set +# CONFIG_SND_ECHO3G is not set +# CONFIG_SND_INDIGO is not set +# CONFIG_SND_INDIGOIO is not set +# CONFIG_SND_INDIGODJ is not set +# CONFIG_SND_EMU10K1 is not set +# CONFIG_SND_EMU10K1X is not set +# CONFIG_SND_ENS1370 is not set +# CONFIG_SND_ENS1371 is not set +# CONFIG_SND_ES1938 is not set +# CONFIG_SND_ES1968 is not set +# CONFIG_SND_FM801 is not set +# CONFIG_SND_HDA_INTEL is not set +# CONFIG_SND_HDSP is not set +# CONFIG_SND_HDSPM is not set +# CONFIG_SND_HIFIER is not set +# CONFIG_SND_ICE1712 is not set +# CONFIG_SND_ICE1724 is not set +CONFIG_SND_INTEL8X0=y +# CONFIG_SND_INTEL8X0M is not set +# CONFIG_SND_KORG1212 is not set +# CONFIG_SND_MAESTRO3 is not set +# CONFIG_SND_MIXART is not set +# CONFIG_SND_NM256 is not set +# CONFIG_SND_PCXHR is not set +# CONFIG_SND_RIPTIDE is not set +# CONFIG_SND_RME32 is not set +# CONFIG_SND_RME96 is not set +# CONFIG_SND_RME9652 is not set +# CONFIG_SND_SONICVIBES is not set +# CONFIG_SND_TRIDENT is not set +# CONFIG_SND_VIA82XX is not set +# CONFIG_SND_VIA82XX_MODEM is not set +# CONFIG_SND_VIRTUOSO is not set +# CONFIG_SND_VX222 is not set +# CONFIG_SND_YMFPCI is not set +CONFIG_SND_PPC=y +# CONFIG_SND_POWERMAC is not set +# CONFIG_SND_AOA is not set +CONFIG_SND_USB=y +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_USX2Y is not set +# CONFIG_SND_USB_CAIAQ is not set +# CONFIG_SND_SOC is not set +# CONFIG_SOUND_PRIME is not set +CONFIG_AC97_BUS=y +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_USB_HIDINPUT_POWERBOOK is not set +# CONFIG_HID_FF is not set +# CONFIG_USB_HIDDEV is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=y + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +CONFIG_USB_EHCI_HCD=y +# CONFIG_USB_EHCI_ROOT_HUB_TT is not set +# CONFIG_USB_EHCI_TT_NEWSCHED is not set +# CONFIG_USB_EHCI_FSL is not set +CONFIG_USB_EHCI_HCD_PPC_OF=y +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_HCD_PPC_OF=y +CONFIG_USB_OHCI_HCD_PPC_OF_BE=y +CONFIG_USB_OHCI_HCD_PPC_OF_LE=y +CONFIG_USB_OHCI_HCD_PCI=y +CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y +CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_SIERRA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +# CONFIG_INFINIBAND is not set +# CONFIG_EDAC is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set + +# +# SPI RTC drivers +# + +# +# Platform RTC drivers +# +CONFIG_RTC_DRV_CMOS=y +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_RTC_DRV_PPC is not set +# CONFIG_DMADEVICES is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +CONFIG_ISO9660_FS=m +CONFIG_JOLIET=y +CONFIG_ZISOFS=y +CONFIG_UDF_FS=m +CONFIG_UDF_NLS=y + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=m +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +CONFIG_NTFS_FS=y +# CONFIG_NTFS_DEBUG is not set +# CONFIG_NTFS_RW is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +CONFIG_ADFS_FS=m +# CONFIG_ADFS_FS_RW is not set +CONFIG_AFFS_FS=m +CONFIG_HFS_FS=m +CONFIG_HFSPLUS_FS=m +CONFIG_BEFS_FS=m +# CONFIG_BEFS_DEBUG is not set +CONFIG_BFS_FS=m +CONFIG_EFS_FS=m +CONFIG_CRAMFS=y +CONFIG_VXFS_FS=m +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +CONFIG_HPFS_FS=m +CONFIG_QNX4FS_FS=m +# CONFIG_ROMFS_FS is not set +CONFIG_SYSV_FS=m +CONFIG_UFS_FS=m +# CONFIG_UFS_FS_WRITE is not set +# CONFIG_UFS_DEBUG is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +CONFIG_NFS_V4=y +CONFIG_ROOT_NFS=y +CONFIG_NFSD=y +# CONFIG_NFSD_V3 is not set +# CONFIG_NFSD_V4 is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_EXPORTFS=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +CONFIG_MAC_PARTITION=y +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y +CONFIG_CRC_ITU_T=m +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=m +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_HAVE_LMB=y + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_SLUB_STATS is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_HIGHMEM is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_HAVE_FTRACE=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +# CONFIG_FTRACE is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_XMON is not set +# CONFIG_IRQSTACKS is not set +# CONFIG_BDI_SWITCH is not set +# CONFIG_BOOTX_TEXT is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +CONFIG_CRYPTO_HMAC=y +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +CONFIG_CRYPTO_SHA1=m +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y +# CONFIG_CRYPTO_DEV_HIFN_795X is not set +# CONFIG_CRYPTO_DEV_TALITOS is not set +# CONFIG_PPC_CLOCK is not set +# CONFIG_VIRTUALIZATION is not set diff --git a/arch/powerpc/configs/86xx/sbc8641d_defconfig b/arch/powerpc/configs/86xx/sbc8641d_defconfig new file mode 100644 index 00000000000..f545421f985 --- /dev/null +++ b/arch/powerpc/configs/86xx/sbc8641d_defconfig @@ -0,0 +1,1481 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.27-rc4 +# Thu Aug 21 00:52:15 2008 +# +# CONFIG_PPC64 is not set + +# +# Processor support +# +CONFIG_6xx=y +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_8xx is not set +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_PPC_FPU=y +CONFIG_ALTIVEC=y +CONFIG_PPC_STD_MMU=y +CONFIG_PPC_STD_MMU_32=y +# CONFIG_PPC_MM_SLICES is not set +CONFIG_SMP=y +CONFIG_NR_CPUS=2 +CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set +CONFIG_IRQ_PER_CPU=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_GENERIC_LOCKBREAK=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +# CONFIG_ARCH_NO_VIRT_TO_BUS is not set +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_OF=y +CONFIG_PPC_UDBG_16550=y +CONFIG_GENERIC_TBSYNC=y +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +CONFIG_DEFAULT_UIMAGE=y +# CONFIG_PPC_DCR_NATIVE is not set +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +CONFIG_BSD_PROCESS_ACCT=y +CONFIG_BSD_PROCESS_ACCT_V3=y +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_GROUP_SCHED=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +CONFIG_RELAY=y +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_PCSPKR_PLATFORM=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_USE_GENERIC_SMP_HELPERS=y +# CONFIG_HAVE_CLK is not set +CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_STOP_MACHINE=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +CONFIG_DEFAULT_CFQ=y +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y + +# +# Platform support +# +CONFIG_PPC_MULTIPLATFORM=y +CONFIG_CLASSIC32=y +CONFIG_PPC_CHRP=y +# CONFIG_MPC5121_ADS is not set +# CONFIG_MPC5121_GENERIC is not set +# CONFIG_PPC_MPC52xx is not set +CONFIG_PPC_PMAC=y +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PPC_82xx is not set +# CONFIG_PQ2ADS is not set +# CONFIG_PPC_83xx is not set +CONFIG_PPC_86xx=y +# CONFIG_MPC8641_HPCN is not set +CONFIG_SBC8641D=y +# CONFIG_MPC8610_HPCD is not set +CONFIG_MPC8641=y +CONFIG_PPC_NATIVE=y +# CONFIG_UDBG_RTAS_CONSOLE is not set +# CONFIG_IPIC is not set +CONFIG_MPIC=y +# CONFIG_MPIC_WEIRD is not set +CONFIG_PPC_I8259=y +CONFIG_PPC_RTAS=y +# CONFIG_RTAS_ERROR_LOGGING is not set +CONFIG_RTAS_PROC=y +# CONFIG_MMIO_NVRAM is not set +CONFIG_PPC_MPC106=y +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +# CONFIG_PPC601_SYNC_FIX is not set +# CONFIG_TAU is not set +# CONFIG_FSL_ULI1575 is not set + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +# CONFIG_NO_HZ is not set +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +CONFIG_SCHED_HRTICK=y +# CONFIG_PREEMPT_NONE is not set +# CONFIG_PREEMPT_VOLUNTARY is not set +CONFIG_PREEMPT=y +# CONFIG_PREEMPT_RCU is not set +CONFIG_BINFMT_ELF=y +CONFIG_BINFMT_MISC=m +# CONFIG_IOMMU_HELPER is not set +# CONFIG_HOTPLUG_CPU is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_HAS_WALK_MEMORY=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y +# CONFIG_KEXEC is not set +CONFIG_IRQ_ALL_CPUS=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_FORCE_MAX_ZONEORDER=11 +# CONFIG_PROC_DEVICETREE is not set +# CONFIG_CMDLINE_BOOL is not set +CONFIG_EXTRA_TARGETS="" +# CONFIG_PM is not set +CONFIG_SECCOMP=y +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +# CONFIG_ISA is not set +CONFIG_ZONE_DMA=y +CONFIG_GENERIC_ISA_DMA=y +CONFIG_PPC_INDIRECT_PCI=y +CONFIG_FSL_SOC=y +CONFIG_FSL_PCI=y +CONFIG_PPC_PCI_CHOICE=y +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_SYSCALL=y +CONFIG_PCIEPORTBUS=y +CONFIG_PCIEAER=y +# CONFIG_PCIEASPM is not set +CONFIG_ARCH_SUPPORTS_MSI=y +# CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y +# CONFIG_PCI_DEBUG is not set +# CONFIG_PCCARD is not set +# CONFIG_HOTPLUG_PCI is not set +# CONFIG_HAS_RAPIDIO is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_PAGE_OFFSET=0xc0000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_PHYSICAL_START=0x00000000 +CONFIG_TASK_SIZE=0xc0000000 +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=m +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +CONFIG_XFRM_IPCOMP=m +CONFIG_NET_KEY=m +# CONFIG_NET_KEY_MIGRATE is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_ADVANCED_ROUTER=y +CONFIG_ASK_IP_FIB_HASH=y +# CONFIG_IP_FIB_TRIE is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_MULTIPLE_TABLES=y +CONFIG_IP_ROUTE_MULTIPATH=y +CONFIG_IP_ROUTE_VERBOSE=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +CONFIG_NET_IPIP=m +CONFIG_NET_IPGRE=m +CONFIG_NET_IPGRE_BROADCAST=y +CONFIG_IP_MROUTE=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +CONFIG_INET_AH=m +CONFIG_INET_ESP=m +CONFIG_INET_IPCOMP=m +CONFIG_INET_XFRM_TUNNEL=m +CONFIG_INET_TUNNEL=m +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IP_VS is not set +CONFIG_IPV6=m +# CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +CONFIG_INET6_AH=m +CONFIG_INET6_ESP=m +CONFIG_INET6_IPCOMP=m +# CONFIG_IPV6_MIP6 is not set +CONFIG_INET6_XFRM_TUNNEL=m +CONFIG_INET6_TUNNEL=m +CONFIG_INET6_XFRM_MODE_TRANSPORT=m +CONFIG_INET6_XFRM_MODE_TUNNEL=m +CONFIG_INET6_XFRM_MODE_BEET=m +# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set +CONFIG_IPV6_SIT=m +CONFIG_IPV6_NDISC_NODETYPE=y +CONFIG_IPV6_TUNNEL=m +# CONFIG_IPV6_MULTIPLE_TABLES is not set +# CONFIG_IPV6_MROUTE is not set +# CONFIG_NETLABEL is not set +# CONFIG_NETWORK_SECMARK is not set +CONFIG_NETFILTER=y +# CONFIG_NETFILTER_DEBUG is not set +CONFIG_NETFILTER_ADVANCED=y +CONFIG_BRIDGE_NETFILTER=y + +# +# Core Netfilter Configuration +# +# CONFIG_NETFILTER_NETLINK_QUEUE is not set +# CONFIG_NETFILTER_NETLINK_LOG is not set +# CONFIG_NF_CONNTRACK is not set +CONFIG_NETFILTER_XTABLES=m +# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set +# CONFIG_NETFILTER_XT_TARGET_DSCP is not set +# CONFIG_NETFILTER_XT_TARGET_MARK is not set +# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set +# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set +# CONFIG_NETFILTER_XT_TARGET_RATEEST is not set +# CONFIG_NETFILTER_XT_TARGET_TRACE is not set +# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set +# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set +# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set +# CONFIG_NETFILTER_XT_MATCH_DCCP is not set +# CONFIG_NETFILTER_XT_MATCH_DSCP is not set +# CONFIG_NETFILTER_XT_MATCH_ESP is not set +# CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set +# CONFIG_NETFILTER_XT_MATCH_LENGTH is not set +# CONFIG_NETFILTER_XT_MATCH_LIMIT is not set +# CONFIG_NETFILTER_XT_MATCH_MAC is not set +# CONFIG_NETFILTER_XT_MATCH_MARK is not set +# CONFIG_NETFILTER_XT_MATCH_OWNER is not set +# CONFIG_NETFILTER_XT_MATCH_POLICY is not set +# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set +# CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set +# CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set +# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set +# CONFIG_NETFILTER_XT_MATCH_RATEEST is not set +# CONFIG_NETFILTER_XT_MATCH_REALM is not set +# CONFIG_NETFILTER_XT_MATCH_SCTP is not set +# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set +# CONFIG_NETFILTER_XT_MATCH_STRING is not set +# CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set +# CONFIG_NETFILTER_XT_MATCH_TIME is not set +# CONFIG_NETFILTER_XT_MATCH_U32 is not set +# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set + +# +# IP: Netfilter Configuration +# +CONFIG_IP_NF_QUEUE=m +CONFIG_IP_NF_IPTABLES=m +CONFIG_IP_NF_MATCH_RECENT=m +CONFIG_IP_NF_MATCH_ECN=m +# CONFIG_IP_NF_MATCH_AH is not set +CONFIG_IP_NF_MATCH_TTL=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m +CONFIG_IP_NF_FILTER=m +CONFIG_IP_NF_TARGET_REJECT=m +CONFIG_IP_NF_TARGET_LOG=m +CONFIG_IP_NF_TARGET_ULOG=m +CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_ECN=m +# CONFIG_IP_NF_TARGET_TTL is not set +CONFIG_IP_NF_RAW=m +# CONFIG_IP_NF_SECURITY is not set +CONFIG_IP_NF_ARPTABLES=m +CONFIG_IP_NF_ARPFILTER=m +CONFIG_IP_NF_ARP_MANGLE=m + +# +# IPv6: Netfilter Configuration +# +CONFIG_IP6_NF_QUEUE=m +CONFIG_IP6_NF_IPTABLES=m +CONFIG_IP6_NF_MATCH_RT=m +CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_HL=m +CONFIG_IP6_NF_MATCH_IPV6HEADER=m +# CONFIG_IP6_NF_MATCH_AH is not set +# CONFIG_IP6_NF_MATCH_MH is not set +CONFIG_IP6_NF_MATCH_EUI64=m +CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_TARGET_LOG=m +# CONFIG_IP6_NF_TARGET_REJECT is not set +CONFIG_IP6_NF_MANGLE=m +# CONFIG_IP6_NF_TARGET_HL is not set +CONFIG_IP6_NF_RAW=m +# CONFIG_IP6_NF_SECURITY is not set + +# +# Bridge: Netfilter Configuration +# +# CONFIG_BRIDGE_NF_EBTABLES is not set +# CONFIG_IP_DCCP is not set +CONFIG_IP_SCTP=m +# CONFIG_SCTP_DBG_MSG is not set +# CONFIG_SCTP_DBG_OBJCNT is not set +# CONFIG_SCTP_HMAC_NONE is not set +# CONFIG_SCTP_HMAC_SHA1 is not set +CONFIG_SCTP_HMAC_MD5=y +CONFIG_TIPC=m +# CONFIG_TIPC_ADVANCED is not set +# CONFIG_TIPC_DEBUG is not set +CONFIG_ATM=m +CONFIG_ATM_CLIP=m +# CONFIG_ATM_CLIP_NO_ICMP is not set +CONFIG_ATM_LANE=m +CONFIG_ATM_MPOA=m +CONFIG_ATM_BR2684=m +# CONFIG_ATM_BR2684_IPFILTER is not set +CONFIG_STP=m +CONFIG_BRIDGE=m +CONFIG_VLAN_8021Q=m +# CONFIG_VLAN_8021Q_GVRP is not set +# CONFIG_DECNET is not set +CONFIG_LLC=m +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +CONFIG_WAN_ROUTER=m +CONFIG_NET_SCHED=y + +# +# Queueing/Scheduling +# +CONFIG_NET_SCH_CBQ=m +CONFIG_NET_SCH_HTB=m +CONFIG_NET_SCH_HFSC=m +CONFIG_NET_SCH_ATM=m +CONFIG_NET_SCH_PRIO=m +CONFIG_NET_SCH_RED=m +CONFIG_NET_SCH_SFQ=m +CONFIG_NET_SCH_TEQL=m +CONFIG_NET_SCH_TBF=m +CONFIG_NET_SCH_GRED=m +CONFIG_NET_SCH_DSMARK=m +CONFIG_NET_SCH_NETEM=m + +# +# Classification +# +CONFIG_NET_CLS=y +# CONFIG_NET_CLS_BASIC is not set +CONFIG_NET_CLS_TCINDEX=m +CONFIG_NET_CLS_ROUTE4=m +CONFIG_NET_CLS_ROUTE=y +CONFIG_NET_CLS_FW=m +CONFIG_NET_CLS_U32=m +# CONFIG_CLS_U32_PERF is not set +# CONFIG_CLS_U32_MARK is not set +CONFIG_NET_CLS_RSVP=m +CONFIG_NET_CLS_RSVP6=m +# CONFIG_NET_CLS_FLOW is not set +# CONFIG_NET_EMATCH is not set +# CONFIG_NET_CLS_ACT is not set +# CONFIG_NET_CLS_IND is not set +CONFIG_NET_SCH_FIFO=y + +# +# Network testing +# +CONFIG_NET_PKTGEN=m +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +CONFIG_FIB_RULES=y + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_CONCAT=y +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +# CONFIG_MTD_CMDLINE_PARTS is not set +# CONFIG_MTD_OF_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +# CONFIG_MTD_CFI_NOSWAP is not set +# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set +CONFIG_MTD_CFI_LE_BYTE_SWAP=y +# CONFIG_MTD_CFI_GEOMETRY is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set +CONFIG_MTD_CFI_INTELEXT=y +# CONFIG_MTD_CFI_AMDSTD is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP_OF=y +# CONFIG_MTD_INTEL_VR_NOR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +CONFIG_OF_DEVICE=y +CONFIG_OF_I2C=y +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_FD is not set +# CONFIG_MAC_FLOPPY is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=m +CONFIG_BLK_DEV_CRYPTOLOOP=m +CONFIG_BLK_DEV_NBD=m +# CONFIG_BLK_DEV_SX8 is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set +CONFIG_MISC_DEVICES=y +# CONFIG_PHANTOM is not set +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_SGI_IOC4 is not set +# CONFIG_TIFM_CORE is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_HP_ILO is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_ATA is not set +CONFIG_MD=y +CONFIG_BLK_DEV_MD=y +CONFIG_MD_LINEAR=y +CONFIG_MD_RAID0=y +CONFIG_MD_RAID1=y +CONFIG_MD_RAID10=y +# CONFIG_MD_RAID456 is not set +CONFIG_MD_MULTIPATH=y +CONFIG_MD_FAULTY=y +CONFIG_BLK_DEV_DM=y +# CONFIG_DM_DEBUG is not set +CONFIG_DM_CRYPT=y +CONFIG_DM_SNAPSHOT=y +CONFIG_DM_MIRROR=y +CONFIG_DM_ZERO=y +# CONFIG_DM_MULTIPATH is not set +# CONFIG_DM_DELAY is not set +# CONFIG_DM_UEVENT is not set +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# Enable only one of the two stacks, unless you know what you are doing +# +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set +# CONFIG_I2O is not set +# CONFIG_MACINTOSH_DRIVERS is not set +CONFIG_NETDEVICES=y +CONFIG_DUMMY=m +CONFIG_BONDING=m +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +CONFIG_TUN=m +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +CONFIG_BROADCOM_PHY=y +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_MACE is not set +# CONFIG_BMAC is not set +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_NET_PCI is not set +# CONFIG_B44 is not set +CONFIG_NETDEV_1000=y +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_E1000E is not set +# CONFIG_IP1000 is not set +# CONFIG_IGB is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_VIA_VELOCITY is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set +CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set +# CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set +# CONFIG_ATL1E is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set +# CONFIG_WAN is not set +CONFIG_ATM_DRIVERS=y +# CONFIG_ATM_DUMMY is not set +# CONFIG_ATM_TCP is not set +# CONFIG_ATM_LANAI is not set +# CONFIG_ATM_ENI is not set +# CONFIG_ATM_FIRESTREAM is not set +# CONFIG_ATM_ZATM is not set +# CONFIG_ATM_NICSTAR is not set +# CONFIG_ATM_IDT77252 is not set +# CONFIG_ATM_AMBASSADOR is not set +# CONFIG_ATM_HORIZON is not set +# CONFIG_ATM_IA is not set +# CONFIG_ATM_FORE200E is not set +# CONFIG_ATM_HE is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +CONFIG_PPP=m +CONFIG_PPP_MULTILINK=y +CONFIG_PPP_FILTER=y +CONFIG_PPP_ASYNC=m +CONFIG_PPP_SYNC_TTY=m +CONFIG_PPP_DEFLATE=m +CONFIG_PPP_BSDCOMP=m +# CONFIG_PPP_MPPE is not set +CONFIG_PPPOE=m +CONFIG_PPPOATM=m +# CONFIG_PPPOL2TP is not set +CONFIG_SLIP=m +CONFIG_SLIP_COMPRESSED=y +CONFIG_SLHC=m +CONFIG_SLIP_SMART=y +CONFIG_SLIP_MODE_SLIP6=y +CONFIG_NETCONSOLE=y +# CONFIG_NETCONSOLE_DYNAMIC is not set +CONFIG_NETPOLL=y +CONFIG_NETPOLL_TRAP=y +CONFIG_NET_POLL_CONTROLLER=y +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +# CONFIG_SERIAL_8250_PCI is not set +CONFIG_SERIAL_8250_NR_UARTS=2 +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_PMACZILOG is not set +# CONFIG_SERIAL_JSM is not set +# CONFIG_SERIAL_OF_PLATFORM is not set +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_BRIQ_PANEL is not set +# CONFIG_HVC_RTAS is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=m +# CONFIG_NVRAM is not set +# CONFIG_GEN_RTC is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# PC SMBus host controller drivers +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI1563 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_ISCH is not set +# CONFIG_I2C_PIIX4 is not set +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_VIA is not set +# CONFIG_I2C_VIAPRO is not set + +# +# Mac SMBus host controller drivers +# +# CONFIG_I2C_HYDRA is not set +CONFIG_I2C_POWERMAC=y + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_MPC=y +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set + +# +# Graphics adapter I2C/DDC channel drivers +# +# CONFIG_I2C_VOODOO3 is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_AT24 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +# CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_AD7414 is not set +# CONFIG_SENSORS_AD7418 is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set +# CONFIG_SENSORS_AMS is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_LM93 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_MAX6650 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_SIS5595 is not set +# CONFIG_SENSORS_DME1737 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set +# CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_VIA686A is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_SENSORS_VT8231 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +CONFIG_SOFT_WATCHDOG=m +# CONFIG_ALIM7101_WDT is not set +# CONFIG_8xxx_WDT is not set +# CONFIG_WATCHDOG_RTAS is not set + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +CONFIG_DAB=y + +# +# Graphics support +# +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +CONFIG_VGA_CONSOLE=y +# CONFIG_VGACON_SOFT_SCROLLBACK is not set +CONFIG_DUMMY_CONSOLE=y +# CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +# CONFIG_USB is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set + +# +# Enable Host or Gadget support to see Inventra options +# + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +# CONFIG_INFINIBAND is not set +# CONFIG_EDAC is not set +# CONFIG_RTC_CLASS is not set +# CONFIG_DMADEVICES is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +CONFIG_EXT2_FS_POSIX_ACL=y +# CONFIG_EXT2_FS_SECURITY is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +CONFIG_EXT3_FS_POSIX_ACL=y +# CONFIG_EXT3_FS_SECURITY is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +CONFIG_FS_MBCACHE=y +CONFIG_REISERFS_FS=m +# CONFIG_REISERFS_CHECK is not set +# CONFIG_REISERFS_PROC_INFO is not set +CONFIG_REISERFS_FS_XATTR=y +CONFIG_REISERFS_FS_POSIX_ACL=y +# CONFIG_REISERFS_FS_SECURITY is not set +# CONFIG_JFS_FS is not set +CONFIG_FS_POSIX_ACL=y +# CONFIG_XFS_FS is not set +CONFIG_OCFS2_FS=m +CONFIG_OCFS2_FS_O2CB=m +CONFIG_OCFS2_FS_STATS=y +CONFIG_OCFS2_DEBUG_MASKLOG=y +# CONFIG_OCFS2_DEBUG_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_AUTOFS_FS=m +CONFIG_AUTOFS4_FS=m +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_CONFIGFS_FS=m + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS2_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +CONFIG_MINIX_FS=m +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +CONFIG_ROMFS_FS=m +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +CONFIG_NFS_V4=y +CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +CONFIG_SMB_FS=m +CONFIG_SMB_NLS_DEFAULT=y +CONFIG_SMB_NLS_REMOTE="cp437" +CONFIG_CIFS=m +# CONFIG_CIFS_STATS is not set +# CONFIG_CIFS_WEAK_PW_HASH is not set +CONFIG_CIFS_XATTR=y +CONFIG_CIFS_POSIX=y +# CONFIG_CIFS_DEBUG2 is not set +# CONFIG_CIFS_EXPERIMENTAL is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MAC_PARTITION=y +CONFIG_MSDOS_PARTITION=y +CONFIG_NLS=m +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=m +CONFIG_NLS_CODEPAGE_737=m +CONFIG_NLS_CODEPAGE_775=m +CONFIG_NLS_CODEPAGE_850=m +CONFIG_NLS_CODEPAGE_852=m +CONFIG_NLS_CODEPAGE_855=m +CONFIG_NLS_CODEPAGE_857=m +CONFIG_NLS_CODEPAGE_860=m +CONFIG_NLS_CODEPAGE_861=m +CONFIG_NLS_CODEPAGE_862=m +CONFIG_NLS_CODEPAGE_863=m +CONFIG_NLS_CODEPAGE_864=m +CONFIG_NLS_CODEPAGE_865=m +CONFIG_NLS_CODEPAGE_866=m +CONFIG_NLS_CODEPAGE_869=m +CONFIG_NLS_CODEPAGE_936=m +CONFIG_NLS_CODEPAGE_950=m +CONFIG_NLS_CODEPAGE_932=m +CONFIG_NLS_CODEPAGE_949=m +CONFIG_NLS_CODEPAGE_874=m +CONFIG_NLS_ISO8859_8=m +CONFIG_NLS_CODEPAGE_1250=m +CONFIG_NLS_CODEPAGE_1251=m +CONFIG_NLS_ASCII=m +CONFIG_NLS_ISO8859_1=m +CONFIG_NLS_ISO8859_2=m +CONFIG_NLS_ISO8859_3=m +CONFIG_NLS_ISO8859_4=m +CONFIG_NLS_ISO8859_5=m +CONFIG_NLS_ISO8859_6=m +CONFIG_NLS_ISO8859_7=m +CONFIG_NLS_ISO8859_9=m +CONFIG_NLS_ISO8859_13=m +CONFIG_NLS_ISO8859_14=m +CONFIG_NLS_ISO8859_15=m +CONFIG_NLS_KOI8_R=m +CONFIG_NLS_KOI8_U=m +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +CONFIG_CRC_CCITT=m +# CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=m +CONFIG_ZLIB_INFLATE=m +CONFIG_ZLIB_DEFLATE=m +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_HAVE_LMB=y + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_HAVE_FTRACE=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +# CONFIG_FTRACE is not set +# CONFIG_PREEMPT_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_XMON is not set +# CONFIG_IRQSTACKS is not set +# CONFIG_VIRQ_DEBUG is not set +# CONFIG_BDI_SWITCH is not set +# CONFIG_BOOTX_TEXT is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +CONFIG_SECURITY=y +CONFIG_SECURITY_NETWORK=y +# CONFIG_SECURITY_NETWORK_XFRM is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0 +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_GF128MUL is not set +CONFIG_CRYPTO_NULL=m +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_AUTHENC=m +CONFIG_CRYPTO_TEST=m + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +CONFIG_CRYPTO_HMAC=y +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +CONFIG_CRYPTO_CRC32C=m +CONFIG_CRYPTO_MD4=m +CONFIG_CRYPTO_MD5=y +CONFIG_CRYPTO_MICHAEL_MIC=m +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +CONFIG_CRYPTO_SHA1=m +CONFIG_CRYPTO_SHA256=m +CONFIG_CRYPTO_SHA512=m +# CONFIG_CRYPTO_TGR192 is not set +CONFIG_CRYPTO_WP512=m + +# +# Ciphers +# +CONFIG_CRYPTO_AES=m +CONFIG_CRYPTO_ANUBIS=m +CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_BLOWFISH=m +# CONFIG_CRYPTO_CAMELLIA is not set +CONFIG_CRYPTO_CAST5=m +CONFIG_CRYPTO_CAST6=m +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +CONFIG_CRYPTO_KHAZAD=m +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +CONFIG_CRYPTO_SERPENT=m +CONFIG_CRYPTO_TEA=m +CONFIG_CRYPTO_TWOFISH=m +CONFIG_CRYPTO_TWOFISH_COMMON=m + +# +# Compression +# +CONFIG_CRYPTO_DEFLATE=m +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y +# CONFIG_CRYPTO_DEV_HIFN_795X is not set +# CONFIG_CRYPTO_DEV_TALITOS is not set +# CONFIG_PPC_CLOCK is not set +# CONFIG_VIRTUALIZATION is not set diff --git a/arch/powerpc/configs/mpc8610_hpcd_defconfig b/arch/powerpc/configs/mpc8610_hpcd_defconfig deleted file mode 100644 index 1a9990731eb..00000000000 --- a/arch/powerpc/configs/mpc8610_hpcd_defconfig +++ /dev/null @@ -1,1497 +0,0 @@ -# -# Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc4 -# Thu Aug 21 00:52:10 2008 -# -# CONFIG_PPC64 is not set - -# -# Processor support -# -CONFIG_6xx=y -# CONFIG_PPC_85xx is not set -# CONFIG_PPC_8xx is not set -# CONFIG_40x is not set -# CONFIG_44x is not set -# CONFIG_E200 is not set -CONFIG_PPC_FPU=y -CONFIG_ALTIVEC=y -CONFIG_PPC_STD_MMU=y -CONFIG_PPC_STD_MMU_32=y -# CONFIG_PPC_MM_SLICES is not set -# CONFIG_SMP is not set -CONFIG_PPC32=y -CONFIG_WORD_SIZE=32 -CONFIG_PPC_MERGE=y -CONFIG_MMU=y -CONFIG_GENERIC_CMOS_UPDATE=y -CONFIG_GENERIC_TIME=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_HARDIRQS=y -# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set -CONFIG_IRQ_PER_CPU=y -CONFIG_STACKTRACE_SUPPORT=y -CONFIG_HAVE_LATENCYTOP_SUPPORT=y -CONFIG_LOCKDEP_SUPPORT=y -CONFIG_RWSEM_XCHGADD_ALGORITHM=y -CONFIG_ARCH_HAS_ILOG2_U32=y -CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_GENERIC_FIND_NEXT_BIT=y -# CONFIG_ARCH_NO_VIRT_TO_BUS is not set -CONFIG_PPC=y -CONFIG_EARLY_PRINTK=y -CONFIG_GENERIC_NVRAM=y -CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y -CONFIG_ARCH_MAY_HAVE_PC_FDC=y -CONFIG_PPC_OF=y -CONFIG_OF=y -CONFIG_PPC_UDBG_16550=y -# CONFIG_GENERIC_TBSYNC is not set -CONFIG_AUDIT_ARCH=y -CONFIG_GENERIC_BUG=y -CONFIG_DEFAULT_UIMAGE=y -CONFIG_HIBERNATE_32=y -CONFIG_ARCH_HIBERNATION_POSSIBLE=y -# CONFIG_PPC_DCR_NATIVE is not set -# CONFIG_PPC_DCR_MMIO is not set -CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" - -# -# General setup -# -CONFIG_EXPERIMENTAL=y -CONFIG_BROKEN_ON_SMP=y -CONFIG_INIT_ENV_ARG_LIMIT=32 -CONFIG_LOCALVERSION="" -CONFIG_LOCALVERSION_AUTO=y -# CONFIG_SWAP is not set -CONFIG_SYSVIPC=y -CONFIG_SYSVIPC_SYSCTL=y -# CONFIG_POSIX_MQUEUE is not set -# CONFIG_BSD_PROCESS_ACCT is not set -# CONFIG_TASKSTATS is not set -# CONFIG_AUDIT is not set -CONFIG_IKCONFIG=y -CONFIG_IKCONFIG_PROC=y -CONFIG_LOG_BUF_SHIFT=14 -# CONFIG_CGROUPS is not set -CONFIG_GROUP_SCHED=y -# CONFIG_FAIR_GROUP_SCHED is not set -# CONFIG_RT_GROUP_SCHED is not set -CONFIG_USER_SCHED=y -# CONFIG_CGROUP_SCHED is not set -CONFIG_SYSFS_DEPRECATED=y -CONFIG_SYSFS_DEPRECATED_V2=y -# CONFIG_RELAY is not set -# CONFIG_NAMESPACES is not set -CONFIG_BLK_DEV_INITRD=y -CONFIG_INITRAMFS_SOURCE="" -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set -CONFIG_SYSCTL=y -CONFIG_EMBEDDED=y -CONFIG_SYSCTL_SYSCALL=y -CONFIG_KALLSYMS=y -# CONFIG_KALLSYMS_ALL is not set -CONFIG_KALLSYMS_EXTRA_PASS=y -CONFIG_HOTPLUG=y -CONFIG_PRINTK=y -CONFIG_BUG=y -# CONFIG_ELF_CORE is not set -CONFIG_PCSPKR_PLATFORM=y -CONFIG_COMPAT_BRK=y -CONFIG_BASE_FULL=y -CONFIG_FUTEX=y -CONFIG_ANON_INODES=y -CONFIG_EPOLL=y -CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y -CONFIG_EVENTFD=y -CONFIG_SHMEM=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_SLUB_DEBUG=y -# CONFIG_SLAB is not set -CONFIG_SLUB=y -# CONFIG_SLOB is not set -# CONFIG_PROFILING is not set -# CONFIG_MARKERS is not set -CONFIG_HAVE_OPROFILE=y -# CONFIG_KPROBES is not set -CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y -CONFIG_HAVE_IOREMAP_PROT=y -CONFIG_HAVE_KPROBES=y -CONFIG_HAVE_KRETPROBES=y -CONFIG_HAVE_ARCH_TRACEHOOK=y -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y -# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set -CONFIG_SLABINFO=y -CONFIG_RT_MUTEXES=y -# CONFIG_TINY_SHMEM is not set -CONFIG_BASE_SMALL=0 -CONFIG_MODULES=y -# CONFIG_MODULE_FORCE_LOAD is not set -CONFIG_MODULE_UNLOAD=y -# CONFIG_MODULE_FORCE_UNLOAD is not set -# CONFIG_MODVERSIONS is not set -# CONFIG_MODULE_SRCVERSION_ALL is not set -CONFIG_KMOD=y -CONFIG_BLOCK=y -# CONFIG_LBD is not set -# CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_LSF is not set -# CONFIG_BLK_DEV_BSG is not set -# CONFIG_BLK_DEV_INTEGRITY is not set - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -# CONFIG_IOSCHED_AS is not set -CONFIG_IOSCHED_DEADLINE=y -# CONFIG_IOSCHED_CFQ is not set -# CONFIG_DEFAULT_AS is not set -CONFIG_DEFAULT_DEADLINE=y -# CONFIG_DEFAULT_CFQ is not set -# CONFIG_DEFAULT_NOOP is not set -CONFIG_DEFAULT_IOSCHED="deadline" -CONFIG_CLASSIC_RCU=y - -# -# Platform support -# -CONFIG_PPC_MULTIPLATFORM=y -CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y -# CONFIG_MPC5121_ADS is not set -# CONFIG_MPC5121_GENERIC is not set -# CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y -# CONFIG_PPC_CELL is not set -# CONFIG_PPC_CELL_NATIVE is not set -# CONFIG_PPC_82xx is not set -# CONFIG_PQ2ADS is not set -# CONFIG_PPC_83xx is not set -CONFIG_PPC_86xx=y -# CONFIG_MPC8641_HPCN is not set -# CONFIG_SBC8641D is not set -CONFIG_MPC8610_HPCD=y -CONFIG_MPC8610=y -# CONFIG_EMBEDDED6xx is not set -CONFIG_PPC_NATIVE=y -# CONFIG_UDBG_RTAS_CONSOLE is not set -# CONFIG_IPIC is not set -CONFIG_MPIC=y -# CONFIG_MPIC_WEIRD is not set -CONFIG_PPC_I8259=y -CONFIG_PPC_RTAS=y -# CONFIG_RTAS_ERROR_LOGGING is not set -CONFIG_RTAS_PROC=y -# CONFIG_MMIO_NVRAM is not set -CONFIG_PPC_MPC106=y -# CONFIG_PPC_970_NAP is not set -# CONFIG_PPC_INDIRECT_IO is not set -# CONFIG_GENERIC_IOMAP is not set -# CONFIG_CPU_FREQ is not set -# CONFIG_PPC601_SYNC_FIX is not set -# CONFIG_TAU is not set -CONFIG_FSL_ULI1575=y - -# -# Kernel options -# -CONFIG_HIGHMEM=y -CONFIG_TICK_ONESHOT=y -CONFIG_NO_HZ=y -CONFIG_HIGH_RES_TIMERS=y -CONFIG_GENERIC_CLOCKEVENTS_BUILD=y -# CONFIG_HZ_100 is not set -# CONFIG_HZ_250 is not set -# CONFIG_HZ_300 is not set -CONFIG_HZ_1000=y -CONFIG_HZ=1000 -CONFIG_SCHED_HRTICK=y -CONFIG_PREEMPT_NONE=y -# CONFIG_PREEMPT_VOLUNTARY is not set -# CONFIG_PREEMPT is not set -CONFIG_BINFMT_ELF=y -# CONFIG_BINFMT_MISC is not set -# CONFIG_IOMMU_HELPER is not set -CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y -CONFIG_ARCH_HAS_WALK_MEMORY=y -CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y -# CONFIG_KEXEC is not set -CONFIG_ARCH_FLATMEM_ENABLE=y -CONFIG_ARCH_POPULATES_NODE_MAP=y -CONFIG_SELECT_MEMORY_MODEL=y -CONFIG_FLATMEM_MANUAL=y -# CONFIG_DISCONTIGMEM_MANUAL is not set -# CONFIG_SPARSEMEM_MANUAL is not set -CONFIG_FLATMEM=y -CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set -CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_SPLIT_PTLOCK_CPUS=4 -CONFIG_MIGRATION=y -# CONFIG_RESOURCES_64BIT is not set -CONFIG_ZONE_DMA_FLAG=1 -CONFIG_BOUNCE=y -CONFIG_VIRT_TO_BUS=y -CONFIG_FORCE_MAX_ZONEORDER=12 -CONFIG_PROC_DEVICETREE=y -# CONFIG_CMDLINE_BOOL is not set -CONFIG_EXTRA_TARGETS="" -# CONFIG_PM is not set -# CONFIG_SECCOMP is not set -CONFIG_ISA_DMA_API=y - -# -# Bus options -# -# CONFIG_ISA is not set -CONFIG_ZONE_DMA=y -CONFIG_GENERIC_ISA_DMA=y -CONFIG_PPC_INDIRECT_PCI=y -CONFIG_FSL_SOC=y -CONFIG_FSL_PCI=y -CONFIG_PPC_PCI_CHOICE=y -CONFIG_PCI=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_SYSCALL=y -CONFIG_PCIEPORTBUS=y -CONFIG_PCIEAER=y -# CONFIG_PCIEASPM is not set -CONFIG_ARCH_SUPPORTS_MSI=y -# CONFIG_PCI_MSI is not set -CONFIG_PCI_LEGACY=y -CONFIG_PCI_DEBUG=y -# CONFIG_PCCARD is not set -# CONFIG_HOTPLUG_PCI is not set -# CONFIG_HAS_RAPIDIO is not set - -# -# Advanced setup -# -# CONFIG_ADVANCED_OPTIONS is not set - -# -# Default settings for advanced configuration options are used -# -CONFIG_LOWMEM_SIZE=0x30000000 -CONFIG_PAGE_OFFSET=0xc0000000 -CONFIG_KERNEL_START=0xc0000000 -CONFIG_PHYSICAL_START=0x00000000 -CONFIG_TASK_SIZE=0xc0000000 -CONFIG_NET=y - -# -# Networking options -# -CONFIG_PACKET=y -# CONFIG_PACKET_MMAP is not set -CONFIG_UNIX=y -CONFIG_XFRM=y -CONFIG_XFRM_USER=y -# CONFIG_XFRM_SUB_POLICY is not set -# CONFIG_XFRM_MIGRATE is not set -# CONFIG_XFRM_STATISTICS is not set -# CONFIG_NET_KEY is not set -CONFIG_INET=y -# CONFIG_IP_MULTICAST is not set -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_FIB_HASH=y -CONFIG_IP_PNP=y -CONFIG_IP_PNP_DHCP=y -CONFIG_IP_PNP_BOOTP=y -CONFIG_IP_PNP_RARP=y -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set -# CONFIG_ARPD is not set -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_XFRM_TUNNEL is not set -CONFIG_INET_TUNNEL=y -CONFIG_INET_XFRM_MODE_TRANSPORT=y -CONFIG_INET_XFRM_MODE_TUNNEL=y -CONFIG_INET_XFRM_MODE_BEET=y -# CONFIG_INET_LRO is not set -CONFIG_INET_DIAG=y -CONFIG_INET_TCP_DIAG=y -# CONFIG_TCP_CONG_ADVANCED is not set -CONFIG_TCP_CONG_CUBIC=y -CONFIG_DEFAULT_TCP_CONG="cubic" -# CONFIG_TCP_MD5SIG is not set -CONFIG_IPV6=y -# CONFIG_IPV6_PRIVACY is not set -# CONFIG_IPV6_ROUTER_PREF is not set -# CONFIG_IPV6_OPTIMISTIC_DAD is not set -# CONFIG_INET6_AH is not set -# CONFIG_INET6_ESP is not set -# CONFIG_INET6_IPCOMP is not set -# CONFIG_IPV6_MIP6 is not set -# CONFIG_INET6_XFRM_TUNNEL is not set -# CONFIG_INET6_TUNNEL is not set -CONFIG_INET6_XFRM_MODE_TRANSPORT=y -CONFIG_INET6_XFRM_MODE_TUNNEL=y -CONFIG_INET6_XFRM_MODE_BEET=y -# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set -CONFIG_IPV6_SIT=y -CONFIG_IPV6_NDISC_NODETYPE=y -# CONFIG_IPV6_TUNNEL is not set -# CONFIG_IPV6_MULTIPLE_TABLES is not set -# CONFIG_IPV6_MROUTE is not set -# CONFIG_NETWORK_SECMARK is not set -# CONFIG_NETFILTER is not set -# CONFIG_IP_DCCP is not set -# CONFIG_IP_SCTP is not set -# CONFIG_TIPC is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set -# CONFIG_NET_SCHED is not set - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_HAMRADIO is not set -# CONFIG_CAN is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set -# CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set -# CONFIG_RFKILL is not set -# CONFIG_NET_9P is not set - -# -# Device Drivers -# - -# -# Generic Driver Options -# -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" -CONFIG_STANDALONE=y -CONFIG_PREVENT_FIRMWARE_BUILD=y -CONFIG_FW_LOADER=y -CONFIG_FIRMWARE_IN_KERNEL=y -CONFIG_EXTRA_FIRMWARE="" -# CONFIG_DEBUG_DRIVER is not set -# CONFIG_DEBUG_DEVRES is not set -# CONFIG_SYS_HYPERVISOR is not set -# CONFIG_CONNECTOR is not set -CONFIG_MTD=y -# CONFIG_MTD_DEBUG is not set -# CONFIG_MTD_CONCAT is not set -CONFIG_MTD_PARTITIONS=y -# CONFIG_MTD_REDBOOT_PARTS is not set -CONFIG_MTD_CMDLINE_PARTS=y -# CONFIG_MTD_OF_PARTS is not set -# CONFIG_MTD_AR7_PARTS is not set - -# -# User Modules And Translation Layers -# -CONFIG_MTD_CHAR=y -CONFIG_MTD_BLKDEVS=y -CONFIG_MTD_BLOCK=y -# CONFIG_FTL is not set -# CONFIG_NFTL is not set -# CONFIG_INFTL is not set -# CONFIG_RFD_FTL is not set -# CONFIG_SSFDC is not set -# CONFIG_MTD_OOPS is not set - -# -# RAM/ROM/Flash chip drivers -# -CONFIG_MTD_CFI=y -# CONFIG_MTD_JEDECPROBE is not set -CONFIG_MTD_GEN_PROBE=y -# CONFIG_MTD_CFI_ADV_OPTIONS is not set -CONFIG_MTD_MAP_BANK_WIDTH_1=y -CONFIG_MTD_MAP_BANK_WIDTH_2=y -CONFIG_MTD_MAP_BANK_WIDTH_4=y -# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set -# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set -# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set -CONFIG_MTD_CFI_I1=y -CONFIG_MTD_CFI_I2=y -# CONFIG_MTD_CFI_I4 is not set -# CONFIG_MTD_CFI_I8 is not set -# CONFIG_MTD_CFI_INTELEXT is not set -CONFIG_MTD_CFI_AMDSTD=y -# CONFIG_MTD_CFI_STAA is not set -CONFIG_MTD_CFI_UTIL=y -# CONFIG_MTD_RAM is not set -# CONFIG_MTD_ROM is not set -# CONFIG_MTD_ABSENT is not set - -# -# Mapping drivers for chip access -# -# CONFIG_MTD_COMPLEX_MAPPINGS is not set -# CONFIG_MTD_PHYSMAP is not set -CONFIG_MTD_PHYSMAP_OF=y -# CONFIG_MTD_INTEL_VR_NOR is not set -# CONFIG_MTD_PLATRAM is not set - -# -# Self-contained MTD device drivers -# -# CONFIG_MTD_PMC551 is not set -# CONFIG_MTD_SLRAM is not set -# CONFIG_MTD_PHRAM is not set -# CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLOCK2MTD is not set - -# -# Disk-On-Chip Device Drivers -# -# CONFIG_MTD_DOC2000 is not set -# CONFIG_MTD_DOC2001 is not set -# CONFIG_MTD_DOC2001PLUS is not set -CONFIG_MTD_NAND=y -# CONFIG_MTD_NAND_VERIFY_WRITE is not set -# CONFIG_MTD_NAND_ECC_SMC is not set -# CONFIG_MTD_NAND_MUSEUM_IDS is not set -CONFIG_MTD_NAND_IDS=y -# CONFIG_MTD_NAND_DISKONCHIP is not set -# CONFIG_MTD_NAND_CAFE is not set -# CONFIG_MTD_NAND_NANDSIM is not set -# CONFIG_MTD_NAND_PLATFORM is not set -CONFIG_MTD_NAND_FSL_ELBC=y -# CONFIG_MTD_ONENAND is not set - -# -# UBI - Unsorted block images -# -# CONFIG_MTD_UBI is not set -CONFIG_OF_DEVICE=y -CONFIG_OF_I2C=y -# CONFIG_PARPORT is not set -CONFIG_BLK_DEV=y -# CONFIG_BLK_DEV_FD is not set -# CONFIG_MAC_FLOPPY is not set -# CONFIG_BLK_CPQ_DA is not set -# CONFIG_BLK_CPQ_CISS_DA is not set -# CONFIG_BLK_DEV_DAC960 is not set -# CONFIG_BLK_DEV_UMEM is not set -# CONFIG_BLK_DEV_COW_COMMON is not set -CONFIG_BLK_DEV_LOOP=y -# CONFIG_BLK_DEV_CRYPTOLOOP is not set -# CONFIG_BLK_DEV_NBD is not set -# CONFIG_BLK_DEV_SX8 is not set -CONFIG_BLK_DEV_RAM=y -CONFIG_BLK_DEV_RAM_COUNT=16 -CONFIG_BLK_DEV_RAM_SIZE=131072 -# CONFIG_BLK_DEV_XIP is not set -# CONFIG_CDROM_PKTCDVD is not set -# CONFIG_ATA_OVER_ETH is not set -# CONFIG_BLK_DEV_HD is not set -CONFIG_MISC_DEVICES=y -# CONFIG_PHANTOM is not set -# CONFIG_EEPROM_93CX6 is not set -# CONFIG_SGI_IOC4 is not set -# CONFIG_TIFM_CORE is not set -# CONFIG_ENCLOSURE_SERVICES is not set -# CONFIG_HP_ILO is not set -CONFIG_HAVE_IDE=y -CONFIG_IDE=y -# CONFIG_BLK_DEV_IDE is not set - -# -# SCSI device support -# -# CONFIG_RAID_ATTRS is not set -CONFIG_SCSI=y -CONFIG_SCSI_DMA=y -CONFIG_SCSI_TGT=y -# CONFIG_SCSI_NETLINK is not set -CONFIG_SCSI_PROC_FS=y - -# -# SCSI support type (disk, tape, CD-ROM) -# -CONFIG_BLK_DEV_SD=y -# CONFIG_CHR_DEV_ST is not set -# CONFIG_CHR_DEV_OSST is not set -# CONFIG_BLK_DEV_SR is not set -CONFIG_CHR_DEV_SG=y -# CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# -# CONFIG_SCSI_MULTI_LUN is not set -# CONFIG_SCSI_CONSTANTS is not set -# CONFIG_SCSI_LOGGING is not set -# CONFIG_SCSI_SCAN_ASYNC is not set -CONFIG_SCSI_WAIT_SCAN=m - -# -# SCSI Transports -# -# CONFIG_SCSI_SPI_ATTRS is not set -# CONFIG_SCSI_FC_ATTRS is not set -# CONFIG_SCSI_ISCSI_ATTRS is not set -# CONFIG_SCSI_SAS_LIBSAS is not set -# CONFIG_SCSI_SRP_ATTRS is not set -CONFIG_SCSI_LOWLEVEL=y -# CONFIG_ISCSI_TCP is not set -# CONFIG_BLK_DEV_3W_XXXX_RAID is not set -# CONFIG_SCSI_3W_9XXX is not set -# CONFIG_SCSI_ACARD is not set -# CONFIG_SCSI_AACRAID is not set -# CONFIG_SCSI_AIC7XXX is not set -# CONFIG_SCSI_AIC7XXX_OLD is not set -# CONFIG_SCSI_AIC79XX is not set -# CONFIG_SCSI_AIC94XX is not set -# CONFIG_SCSI_DPT_I2O is not set -# CONFIG_SCSI_ADVANSYS is not set -# CONFIG_SCSI_ARCMSR is not set -# CONFIG_MEGARAID_NEWGEN is not set -# CONFIG_MEGARAID_LEGACY is not set -# CONFIG_MEGARAID_SAS is not set -# CONFIG_SCSI_HPTIOP is not set -# CONFIG_SCSI_BUSLOGIC is not set -# CONFIG_SCSI_DMX3191D is not set -# CONFIG_SCSI_EATA is not set -# CONFIG_SCSI_FUTURE_DOMAIN is not set -# CONFIG_SCSI_GDTH is not set -# CONFIG_SCSI_IPS is not set -# CONFIG_SCSI_INITIO is not set -# CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set -# CONFIG_SCSI_STEX is not set -# CONFIG_SCSI_SYM53C8XX_2 is not set -# CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_1280 is not set -# CONFIG_SCSI_QLA_FC is not set -# CONFIG_SCSI_QLA_ISCSI is not set -# CONFIG_SCSI_LPFC is not set -# CONFIG_SCSI_DC395x is not set -# CONFIG_SCSI_DC390T is not set -# CONFIG_SCSI_NSP32 is not set -# CONFIG_SCSI_DEBUG is not set -# CONFIG_SCSI_MESH is not set -# CONFIG_SCSI_MAC53C94 is not set -# CONFIG_SCSI_SRP is not set -# CONFIG_SCSI_DH is not set -CONFIG_ATA=y -# CONFIG_ATA_NONSTANDARD is not set -CONFIG_SATA_PMP=y -CONFIG_SATA_AHCI=y -# CONFIG_SATA_SIL24 is not set -# CONFIG_SATA_FSL is not set -CONFIG_ATA_SFF=y -# CONFIG_SATA_SVW is not set -# CONFIG_ATA_PIIX is not set -# CONFIG_SATA_MV is not set -# CONFIG_SATA_NV is not set -# CONFIG_PDC_ADMA is not set -# CONFIG_SATA_QSTOR is not set -# CONFIG_SATA_PROMISE is not set -# CONFIG_SATA_SX4 is not set -# CONFIG_SATA_SIL is not set -# CONFIG_SATA_SIS is not set -# CONFIG_SATA_ULI is not set -# CONFIG_SATA_VIA is not set -# CONFIG_SATA_VITESSE is not set -# CONFIG_SATA_INIC162X is not set -CONFIG_PATA_ALI=y -# CONFIG_PATA_AMD is not set -# CONFIG_PATA_ARTOP is not set -# CONFIG_PATA_ATIIXP is not set -# CONFIG_PATA_CMD640_PCI is not set -# CONFIG_PATA_CMD64X is not set -# CONFIG_PATA_CS5520 is not set -# CONFIG_PATA_CS5530 is not set -# CONFIG_PATA_CYPRESS is not set -# CONFIG_PATA_EFAR is not set -# CONFIG_ATA_GENERIC is not set -# CONFIG_PATA_HPT366 is not set -# CONFIG_PATA_HPT37X is not set -# CONFIG_PATA_HPT3X2N is not set -# CONFIG_PATA_HPT3X3 is not set -# CONFIG_PATA_IT821X is not set -# CONFIG_PATA_IT8213 is not set -# CONFIG_PATA_JMICRON is not set -# CONFIG_PATA_TRIFLEX is not set -# CONFIG_PATA_MARVELL is not set -# CONFIG_PATA_MPIIX is not set -# CONFIG_PATA_OLDPIIX is not set -# CONFIG_PATA_NETCELL is not set -# CONFIG_PATA_NINJA32 is not set -# CONFIG_PATA_NS87410 is not set -# CONFIG_PATA_NS87415 is not set -# CONFIG_PATA_OPTI is not set -# CONFIG_PATA_OPTIDMA is not set -# CONFIG_PATA_PDC_OLD is not set -# CONFIG_PATA_RADISYS is not set -# CONFIG_PATA_RZ1000 is not set -# CONFIG_PATA_SC1200 is not set -# CONFIG_PATA_SERVERWORKS is not set -# CONFIG_PATA_PDC2027X is not set -# CONFIG_PATA_SIL680 is not set -# CONFIG_PATA_SIS is not set -# CONFIG_PATA_VIA is not set -# CONFIG_PATA_WINBOND is not set -# CONFIG_PATA_PLATFORM is not set -# CONFIG_PATA_SCH is not set -# CONFIG_MD is not set -# CONFIG_FUSION is not set - -# -# IEEE 1394 (FireWire) support -# - -# -# Enable only one of the two stacks, unless you know what you are doing -# -# CONFIG_FIREWIRE is not set -# CONFIG_IEEE1394 is not set -# CONFIG_I2O is not set -# CONFIG_MACINTOSH_DRIVERS is not set -CONFIG_NETDEVICES=y -CONFIG_DUMMY=y -# CONFIG_BONDING is not set -# CONFIG_MACVLAN is not set -# CONFIG_EQUALIZER is not set -# CONFIG_TUN is not set -# CONFIG_VETH is not set -# CONFIG_ARCNET is not set -# CONFIG_PHYLIB is not set -CONFIG_NET_ETHERNET=y -# CONFIG_MII is not set -# CONFIG_MACE is not set -# CONFIG_BMAC is not set -# CONFIG_HAPPYMEAL is not set -# CONFIG_SUNGEM is not set -# CONFIG_CASSINI is not set -# CONFIG_NET_VENDOR_3COM is not set -CONFIG_NET_TULIP=y -# CONFIG_DE2104X is not set -# CONFIG_TULIP is not set -# CONFIG_DE4X5 is not set -# CONFIG_WINBOND_840 is not set -# CONFIG_DM9102 is not set -CONFIG_ULI526X=y -# CONFIG_HP100 is not set -# CONFIG_IBM_NEW_EMAC_ZMII is not set -# CONFIG_IBM_NEW_EMAC_RGMII is not set -# CONFIG_IBM_NEW_EMAC_TAH is not set -# CONFIG_IBM_NEW_EMAC_EMAC4 is not set -# CONFIG_NET_PCI is not set -# CONFIG_B44 is not set -# CONFIG_NETDEV_1000 is not set -# CONFIG_NETDEV_10000 is not set -# CONFIG_TR is not set - -# -# Wireless LAN -# -# CONFIG_WLAN_PRE80211 is not set -# CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI_LEDS is not set -# CONFIG_WAN is not set -# CONFIG_FDDI is not set -# CONFIG_HIPPI is not set -# CONFIG_PPP is not set -# CONFIG_SLIP is not set -# CONFIG_NET_FC is not set -# CONFIG_NETCONSOLE is not set -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set -# CONFIG_ISDN is not set -# CONFIG_PHONE is not set - -# -# Input device support -# -CONFIG_INPUT=y -# CONFIG_INPUT_FF_MEMLESS is not set -# CONFIG_INPUT_POLLDEV is not set - -# -# Userland interfaces -# -# CONFIG_INPUT_MOUSEDEV is not set -# CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_EVDEV is not set -# CONFIG_INPUT_EVBUG is not set - -# -# Input Device Drivers -# -# CONFIG_INPUT_KEYBOARD is not set -# CONFIG_INPUT_MOUSE is not set -# CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TABLET is not set -# CONFIG_INPUT_TOUCHSCREEN is not set -# CONFIG_INPUT_MISC is not set - -# -# Hardware I/O ports -# -CONFIG_SERIO=y -CONFIG_SERIO_I8042=y -CONFIG_SERIO_SERPORT=y -# CONFIG_SERIO_PCIPS2 is not set -CONFIG_SERIO_LIBPS2=y -# CONFIG_SERIO_RAW is not set -# CONFIG_SERIO_XILINX_XPS_PS2 is not set -# CONFIG_GAMEPORT is not set - -# -# Character devices -# -CONFIG_VT=y -CONFIG_CONSOLE_TRANSLATIONS=y -CONFIG_VT_CONSOLE=y -CONFIG_HW_CONSOLE=y -# CONFIG_VT_HW_CONSOLE_BINDING is not set -CONFIG_DEVKMEM=y -# CONFIG_SERIAL_NONSTANDARD is not set -# CONFIG_NOZOMI is not set - -# -# Serial drivers -# -CONFIG_SERIAL_8250=y -CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_PCI=y -CONFIG_SERIAL_8250_NR_UARTS=2 -CONFIG_SERIAL_8250_RUNTIME_UARTS=2 -CONFIG_SERIAL_8250_EXTENDED=y -CONFIG_SERIAL_8250_MANY_PORTS=y -CONFIG_SERIAL_8250_SHARE_IRQ=y -CONFIG_SERIAL_8250_DETECT_IRQ=y -CONFIG_SERIAL_8250_RSA=y - -# -# Non-8250 serial port support -# -# CONFIG_SERIAL_UARTLITE is not set -CONFIG_SERIAL_CORE=y -CONFIG_SERIAL_CORE_CONSOLE=y -# CONFIG_SERIAL_PMACZILOG is not set -# CONFIG_SERIAL_JSM is not set -# CONFIG_SERIAL_OF_PLATFORM is not set -CONFIG_UNIX98_PTYS=y -# CONFIG_LEGACY_PTYS is not set -# CONFIG_BRIQ_PANEL is not set -# CONFIG_HVC_RTAS is not set -# CONFIG_IPMI_HANDLER is not set -# CONFIG_HW_RANDOM is not set -# CONFIG_NVRAM is not set -# CONFIG_R3964 is not set -# CONFIG_APPLICOM is not set -# CONFIG_RAW_DRIVER is not set -# CONFIG_TCG_TPM is not set -CONFIG_DEVPORT=y -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -# CONFIG_I2C_CHARDEV is not set -CONFIG_I2C_HELPER_AUTO=y - -# -# I2C Hardware Bus support -# - -# -# PC SMBus host controller drivers -# -# CONFIG_I2C_ALI1535 is not set -# CONFIG_I2C_ALI1563 is not set -# CONFIG_I2C_ALI15X3 is not set -# CONFIG_I2C_AMD756 is not set -# CONFIG_I2C_AMD8111 is not set -# CONFIG_I2C_I801 is not set -# CONFIG_I2C_ISCH is not set -# CONFIG_I2C_PIIX4 is not set -# CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_SIS5595 is not set -# CONFIG_I2C_SIS630 is not set -# CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_VIA is not set -# CONFIG_I2C_VIAPRO is not set - -# -# Mac SMBus host controller drivers -# -# CONFIG_I2C_HYDRA is not set -CONFIG_I2C_POWERMAC=y - -# -# I2C system bus drivers (mostly embedded / system-on-chip) -# -CONFIG_I2C_MPC=y -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_SIMTEC is not set - -# -# External I2C/SMBus adapter drivers -# -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_TAOS_EVM is not set - -# -# Graphics adapter I2C/DDC channel drivers -# -# CONFIG_I2C_VOODOO3 is not set - -# -# Other I2C/SMBus bus drivers -# -# CONFIG_I2C_PCA_PLATFORM is not set -# CONFIG_I2C_STUB is not set - -# -# Miscellaneous I2C Chip support -# -# CONFIG_DS1682 is not set -# CONFIG_AT24 is not set -# CONFIG_SENSORS_EEPROM is not set -# CONFIG_SENSORS_PCF8574 is not set -# CONFIG_PCF8575 is not set -# CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_MAX6875 is not set -# CONFIG_SENSORS_TSL2550 is not set -# CONFIG_I2C_DEBUG_CORE is not set -# CONFIG_I2C_DEBUG_ALGO is not set -# CONFIG_I2C_DEBUG_BUS is not set -# CONFIG_I2C_DEBUG_CHIP is not set -# CONFIG_SPI is not set -CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y -# CONFIG_GPIOLIB is not set -# CONFIG_W1 is not set -# CONFIG_POWER_SUPPLY is not set -# CONFIG_HWMON is not set -# CONFIG_THERMAL is not set -# CONFIG_THERMAL_HWMON is not set -# CONFIG_WATCHDOG is not set - -# -# Sonics Silicon Backplane -# -CONFIG_SSB_POSSIBLE=y -# CONFIG_SSB is not set - -# -# Multifunction device drivers -# -# CONFIG_MFD_CORE is not set -# CONFIG_MFD_SM501 is not set -# CONFIG_HTC_PASIC3 is not set -# CONFIG_MFD_TMIO is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y - -# -# Graphics support -# -# CONFIG_AGP is not set -# CONFIG_DRM is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -CONFIG_FB=y -# CONFIG_FIRMWARE_EDID is not set -# CONFIG_FB_DDC is not set -CONFIG_FB_CFB_FILLRECT=y -CONFIG_FB_CFB_COPYAREA=y -CONFIG_FB_CFB_IMAGEBLIT=y -# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set -# CONFIG_FB_SYS_FILLRECT is not set -# CONFIG_FB_SYS_COPYAREA is not set -# CONFIG_FB_SYS_IMAGEBLIT is not set -# CONFIG_FB_FOREIGN_ENDIAN is not set -# CONFIG_FB_SYS_FOPS is not set -# CONFIG_FB_SVGALIB is not set -# CONFIG_FB_MACMODES is not set -# CONFIG_FB_BACKLIGHT is not set -# CONFIG_FB_MODE_HELPERS is not set -# CONFIG_FB_TILEBLITTING is not set - -# -# Frame buffer hardware drivers -# -# CONFIG_FB_CIRRUS is not set -# CONFIG_FB_PM2 is not set -# CONFIG_FB_CYBER2000 is not set -# CONFIG_FB_OF is not set -# CONFIG_FB_CONTROL is not set -# CONFIG_FB_PLATINUM is not set -# CONFIG_FB_VALKYRIE is not set -# CONFIG_FB_CT65550 is not set -# CONFIG_FB_ASILIANT is not set -# CONFIG_FB_IMSTT is not set -# CONFIG_FB_VGA16 is not set -# CONFIG_FB_S1D13XXX is not set -# CONFIG_FB_NVIDIA is not set -# CONFIG_FB_RIVA is not set -# CONFIG_FB_MATROX is not set -# CONFIG_FB_RADEON is not set -# CONFIG_FB_ATY128 is not set -# CONFIG_FB_ATY is not set -# CONFIG_FB_S3 is not set -# CONFIG_FB_SAVAGE is not set -# CONFIG_FB_SIS is not set -# CONFIG_FB_NEOMAGIC is not set -# CONFIG_FB_KYRO is not set -# CONFIG_FB_3DFX is not set -# CONFIG_FB_VOODOO1 is not set -# CONFIG_FB_VT8623 is not set -# CONFIG_FB_TRIDENT is not set -# CONFIG_FB_ARK is not set -# CONFIG_FB_PM3 is not set -# CONFIG_FB_CARMINE is not set -CONFIG_FB_FSL_DIU=y -# CONFIG_FB_IBM_GXT4500 is not set -# CONFIG_FB_VIRTUAL is not set -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set - -# -# Display device support -# -# CONFIG_DISPLAY_SUPPORT is not set - -# -# Console display driver support -# -CONFIG_VGA_CONSOLE=y -# CONFIG_VGACON_SOFT_SCROLLBACK is not set -CONFIG_DUMMY_CONSOLE=y -# CONFIG_FRAMEBUFFER_CONSOLE is not set -# CONFIG_LOGO is not set -CONFIG_SOUND=y -CONFIG_SND=y -CONFIG_SND_TIMER=y -CONFIG_SND_PCM=y -# CONFIG_SND_SEQUENCER is not set -CONFIG_SND_OSSEMUL=y -CONFIG_SND_MIXER_OSS=y -CONFIG_SND_PCM_OSS=y -CONFIG_SND_PCM_OSS_PLUGINS=y -# CONFIG_SND_DYNAMIC_MINORS is not set -# CONFIG_SND_SUPPORT_OLD_API is not set -CONFIG_SND_VERBOSE_PROCFS=y -# CONFIG_SND_VERBOSE_PRINTK is not set -# CONFIG_SND_DEBUG is not set -CONFIG_SND_DRIVERS=y -# CONFIG_SND_DUMMY is not set -# CONFIG_SND_MTPAV is not set -# CONFIG_SND_SERIAL_U16550 is not set -# CONFIG_SND_MPU401 is not set -CONFIG_SND_PCI=y -# CONFIG_SND_AD1889 is not set -# CONFIG_SND_ALS300 is not set -# CONFIG_SND_ALS4000 is not set -# CONFIG_SND_ALI5451 is not set -# CONFIG_SND_ATIIXP is not set -# CONFIG_SND_ATIIXP_MODEM is not set -# CONFIG_SND_AU8810 is not set -# CONFIG_SND_AU8820 is not set -# CONFIG_SND_AU8830 is not set -# CONFIG_SND_AW2 is not set -# CONFIG_SND_AZT3328 is not set -# CONFIG_SND_BT87X is not set -# CONFIG_SND_CA0106 is not set -# CONFIG_SND_CMIPCI is not set -# CONFIG_SND_OXYGEN is not set -# CONFIG_SND_CS4281 is not set -# CONFIG_SND_CS46XX is not set -# CONFIG_SND_CS5530 is not set -# CONFIG_SND_DARLA20 is not set -# CONFIG_SND_GINA20 is not set -# CONFIG_SND_LAYLA20 is not set -# CONFIG_SND_DARLA24 is not set -# CONFIG_SND_GINA24 is not set -# CONFIG_SND_LAYLA24 is not set -# CONFIG_SND_MONA is not set -# CONFIG_SND_MIA is not set -# CONFIG_SND_ECHO3G is not set -# CONFIG_SND_INDIGO is not set -# CONFIG_SND_INDIGOIO is not set -# CONFIG_SND_INDIGODJ is not set -# CONFIG_SND_EMU10K1 is not set -# CONFIG_SND_EMU10K1X is not set -# CONFIG_SND_ENS1370 is not set -# CONFIG_SND_ENS1371 is not set -# CONFIG_SND_ES1938 is not set -# CONFIG_SND_ES1968 is not set -# CONFIG_SND_FM801 is not set -# CONFIG_SND_HDA_INTEL is not set -# CONFIG_SND_HDSP is not set -# CONFIG_SND_HDSPM is not set -# CONFIG_SND_HIFIER is not set -# CONFIG_SND_ICE1712 is not set -# CONFIG_SND_ICE1724 is not set -# CONFIG_SND_INTEL8X0 is not set -# CONFIG_SND_INTEL8X0M is not set -# CONFIG_SND_KORG1212 is not set -# CONFIG_SND_MAESTRO3 is not set -# CONFIG_SND_MIXART is not set -# CONFIG_SND_NM256 is not set -# CONFIG_SND_PCXHR is not set -# CONFIG_SND_RIPTIDE is not set -# CONFIG_SND_RME32 is not set -# CONFIG_SND_RME96 is not set -# CONFIG_SND_RME9652 is not set -# CONFIG_SND_SONICVIBES is not set -# CONFIG_SND_TRIDENT is not set -# CONFIG_SND_VIA82XX is not set -# CONFIG_SND_VIA82XX_MODEM is not set -# CONFIG_SND_VIRTUOSO is not set -# CONFIG_SND_VX222 is not set -# CONFIG_SND_YMFPCI is not set -CONFIG_SND_PPC=y -# CONFIG_SND_POWERMAC is not set -# CONFIG_SND_AOA is not set -CONFIG_SND_SOC=y -CONFIG_SND_SOC_MPC8610=y -CONFIG_SND_SOC_MPC8610_HPCD=y -CONFIG_SND_SOC_CS4270=y -CONFIG_SND_SOC_CS4270_VD33_ERRATA=y -# CONFIG_SOUND_PRIME is not set -CONFIG_HID_SUPPORT=y -CONFIG_HID=y -# CONFIG_HID_DEBUG is not set -# CONFIG_HIDRAW is not set -CONFIG_USB_SUPPORT=y -CONFIG_USB_ARCH_HAS_HCD=y -CONFIG_USB_ARCH_HAS_OHCI=y -CONFIG_USB_ARCH_HAS_EHCI=y -# CONFIG_USB is not set -# CONFIG_USB_OTG_WHITELIST is not set -# CONFIG_USB_OTG_BLACKLIST_HUB is not set - -# -# Enable Host or Gadget support to see Inventra options -# - -# -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' -# -# CONFIG_USB_GADGET is not set -# CONFIG_MMC is not set -# CONFIG_MEMSTICK is not set -# CONFIG_NEW_LEDS is not set -# CONFIG_ACCESSIBILITY is not set -# CONFIG_INFINIBAND is not set -# CONFIG_EDAC is not set -CONFIG_RTC_LIB=y -CONFIG_RTC_CLASS=y -CONFIG_RTC_HCTOSYS=y -CONFIG_RTC_HCTOSYS_DEVICE="rtc0" -# CONFIG_RTC_DEBUG is not set - -# -# RTC interfaces -# -CONFIG_RTC_INTF_SYSFS=y -CONFIG_RTC_INTF_PROC=y -CONFIG_RTC_INTF_DEV=y -# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set -# CONFIG_RTC_DRV_TEST is not set - -# -# I2C RTC drivers -# -# CONFIG_RTC_DRV_DS1307 is not set -# CONFIG_RTC_DRV_DS1374 is not set -# CONFIG_RTC_DRV_DS1672 is not set -# CONFIG_RTC_DRV_MAX6900 is not set -# CONFIG_RTC_DRV_RS5C372 is not set -# CONFIG_RTC_DRV_ISL1208 is not set -# CONFIG_RTC_DRV_X1205 is not set -# CONFIG_RTC_DRV_PCF8563 is not set -# CONFIG_RTC_DRV_PCF8583 is not set -# CONFIG_RTC_DRV_M41T80 is not set -# CONFIG_RTC_DRV_S35390A is not set -# CONFIG_RTC_DRV_FM3130 is not set - -# -# SPI RTC drivers -# - -# -# Platform RTC drivers -# -CONFIG_RTC_DRV_CMOS=y -# CONFIG_RTC_DRV_DS1511 is not set -# CONFIG_RTC_DRV_DS1553 is not set -# CONFIG_RTC_DRV_DS1742 is not set -# CONFIG_RTC_DRV_STK17TA8 is not set -# CONFIG_RTC_DRV_M48T86 is not set -# CONFIG_RTC_DRV_M48T59 is not set -# CONFIG_RTC_DRV_V3020 is not set - -# -# on-CPU RTC drivers -# -# CONFIG_RTC_DRV_PPC is not set -# CONFIG_DMADEVICES is not set -# CONFIG_UIO is not set - -# -# File systems -# -CONFIG_EXT2_FS=y -# CONFIG_EXT2_FS_XATTR is not set -# CONFIG_EXT2_FS_XIP is not set -CONFIG_EXT3_FS=y -CONFIG_EXT3_FS_XATTR=y -# CONFIG_EXT3_FS_POSIX_ACL is not set -# CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set -CONFIG_JBD=y -CONFIG_FS_MBCACHE=y -# CONFIG_REISERFS_FS is not set -# CONFIG_JFS_FS is not set -# CONFIG_FS_POSIX_ACL is not set -# CONFIG_XFS_FS is not set -# CONFIG_OCFS2_FS is not set -# CONFIG_DNOTIFY is not set -# CONFIG_INOTIFY is not set -# CONFIG_QUOTA is not set -# CONFIG_AUTOFS_FS is not set -# CONFIG_AUTOFS4_FS is not set -# CONFIG_FUSE_FS is not set - -# -# CD-ROM/DVD Filesystems -# -# CONFIG_ISO9660_FS is not set -# CONFIG_UDF_FS is not set - -# -# DOS/FAT/NT Filesystems -# -# CONFIG_MSDOS_FS is not set -# CONFIG_VFAT_FS is not set -# CONFIG_NTFS_FS is not set - -# -# Pseudo filesystems -# -CONFIG_PROC_FS=y -CONFIG_PROC_KCORE=y -CONFIG_PROC_SYSCTL=y -CONFIG_SYSFS=y -CONFIG_TMPFS=y -# CONFIG_TMPFS_POSIX_ACL is not set -# CONFIG_HUGETLB_PAGE is not set -# CONFIG_CONFIGFS_FS is not set - -# -# Miscellaneous filesystems -# -# CONFIG_ADFS_FS is not set -# CONFIG_AFFS_FS is not set -# CONFIG_HFS_FS is not set -# CONFIG_HFSPLUS_FS is not set -# CONFIG_BEFS_FS is not set -# CONFIG_BFS_FS is not set -# CONFIG_EFS_FS is not set -# CONFIG_JFFS2_FS is not set -# CONFIG_CRAMFS is not set -# CONFIG_VXFS_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_OMFS_FS is not set -# CONFIG_HPFS_FS is not set -# CONFIG_QNX4FS_FS is not set -# CONFIG_ROMFS_FS is not set -# CONFIG_SYSV_FS is not set -# CONFIG_UFS_FS is not set -CONFIG_NETWORK_FILESYSTEMS=y -CONFIG_NFS_FS=y -CONFIG_NFS_V3=y -# CONFIG_NFS_V3_ACL is not set -# CONFIG_NFS_V4 is not set -CONFIG_ROOT_NFS=y -CONFIG_NFSD=y -# CONFIG_NFSD_V3 is not set -# CONFIG_NFSD_V4 is not set -CONFIG_LOCKD=y -CONFIG_LOCKD_V4=y -CONFIG_EXPORTFS=y -CONFIG_NFS_COMMON=y -CONFIG_SUNRPC=y -# CONFIG_RPCSEC_GSS_KRB5 is not set -# CONFIG_RPCSEC_GSS_SPKM3 is not set -# CONFIG_SMB_FS is not set -# CONFIG_CIFS is not set -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_AFS_FS is not set - -# -# Partition Types -# -CONFIG_PARTITION_ADVANCED=y -# CONFIG_ACORN_PARTITION is not set -# CONFIG_OSF_PARTITION is not set -# CONFIG_AMIGA_PARTITION is not set -# CONFIG_ATARI_PARTITION is not set -# CONFIG_MAC_PARTITION is not set -CONFIG_MSDOS_PARTITION=y -# CONFIG_BSD_DISKLABEL is not set -# CONFIG_MINIX_SUBPARTITION is not set -# CONFIG_SOLARIS_X86_PARTITION is not set -# CONFIG_UNIXWARE_DISKLABEL is not set -CONFIG_LDM_PARTITION=y -# CONFIG_LDM_DEBUG is not set -# CONFIG_SGI_PARTITION is not set -# CONFIG_ULTRIX_PARTITION is not set -# CONFIG_SUN_PARTITION is not set -# CONFIG_KARMA_PARTITION is not set -# CONFIG_EFI_PARTITION is not set -# CONFIG_SYSV68_PARTITION is not set -CONFIG_NLS=y -CONFIG_NLS_DEFAULT="iso8859-1" -# CONFIG_NLS_CODEPAGE_437 is not set -# CONFIG_NLS_CODEPAGE_737 is not set -# CONFIG_NLS_CODEPAGE_775 is not set -# CONFIG_NLS_CODEPAGE_850 is not set -# CONFIG_NLS_CODEPAGE_852 is not set -# CONFIG_NLS_CODEPAGE_855 is not set -# CONFIG_NLS_CODEPAGE_857 is not set -# CONFIG_NLS_CODEPAGE_860 is not set -# CONFIG_NLS_CODEPAGE_861 is not set -# CONFIG_NLS_CODEPAGE_862 is not set -# CONFIG_NLS_CODEPAGE_863 is not set -# CONFIG_NLS_CODEPAGE_864 is not set -# CONFIG_NLS_CODEPAGE_865 is not set -# CONFIG_NLS_CODEPAGE_866 is not set -# CONFIG_NLS_CODEPAGE_869 is not set -# CONFIG_NLS_CODEPAGE_936 is not set -# CONFIG_NLS_CODEPAGE_950 is not set -# CONFIG_NLS_CODEPAGE_932 is not set -# CONFIG_NLS_CODEPAGE_949 is not set -# CONFIG_NLS_CODEPAGE_874 is not set -# CONFIG_NLS_ISO8859_8 is not set -# CONFIG_NLS_CODEPAGE_1250 is not set -# CONFIG_NLS_CODEPAGE_1251 is not set -# CONFIG_NLS_ASCII is not set -# CONFIG_NLS_ISO8859_1 is not set -# CONFIG_NLS_ISO8859_2 is not set -# CONFIG_NLS_ISO8859_3 is not set -# CONFIG_NLS_ISO8859_4 is not set -# CONFIG_NLS_ISO8859_5 is not set -# CONFIG_NLS_ISO8859_6 is not set -# CONFIG_NLS_ISO8859_7 is not set -# CONFIG_NLS_ISO8859_9 is not set -# CONFIG_NLS_ISO8859_13 is not set -# CONFIG_NLS_ISO8859_14 is not set -# CONFIG_NLS_ISO8859_15 is not set -# CONFIG_NLS_KOI8_R is not set -# CONFIG_NLS_KOI8_U is not set -# CONFIG_NLS_UTF8 is not set -# CONFIG_DLM is not set - -# -# Library routines -# -CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_CRC_CCITT is not set -# CONFIG_CRC16 is not set -CONFIG_CRC_T10DIF=y -# CONFIG_CRC_ITU_T is not set -CONFIG_CRC32=y -# CONFIG_CRC7 is not set -# CONFIG_LIBCRC32C is not set -CONFIG_PLIST=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HAS_DMA=y -CONFIG_HAVE_LMB=y - -# -# Kernel hacking -# -# CONFIG_PRINTK_TIME is not set -CONFIG_ENABLE_WARN_DEPRECATED=y -CONFIG_ENABLE_MUST_CHECK=y -CONFIG_FRAME_WARN=1024 -# CONFIG_MAGIC_SYSRQ is not set -# CONFIG_UNUSED_SYMBOLS is not set -# CONFIG_DEBUG_FS is not set -# CONFIG_HEADERS_CHECK is not set -CONFIG_DEBUG_KERNEL=y -CONFIG_DEBUG_SHIRQ=y -CONFIG_DETECT_SOFTLOCKUP=y -# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set -CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 -CONFIG_SCHED_DEBUG=y -# CONFIG_SCHEDSTATS is not set -# CONFIG_TIMER_STATS is not set -# CONFIG_DEBUG_OBJECTS is not set -# CONFIG_SLUB_DEBUG_ON is not set -# CONFIG_SLUB_STATS is not set -# CONFIG_DEBUG_RT_MUTEXES is not set -# CONFIG_RT_MUTEX_TESTER is not set -# CONFIG_DEBUG_SPINLOCK is not set -# CONFIG_DEBUG_MUTEXES is not set -# CONFIG_DEBUG_SPINLOCK_SLEEP is not set -# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set -# CONFIG_DEBUG_KOBJECT is not set -# CONFIG_DEBUG_HIGHMEM is not set -CONFIG_DEBUG_BUGVERBOSE=y -CONFIG_DEBUG_INFO=y -# CONFIG_DEBUG_VM is not set -# CONFIG_DEBUG_WRITECOUNT is not set -# CONFIG_DEBUG_MEMORY_INIT is not set -# CONFIG_DEBUG_LIST is not set -# CONFIG_DEBUG_SG is not set -# CONFIG_BOOT_PRINTK_DELAY is not set -# CONFIG_RCU_TORTURE_TEST is not set -# CONFIG_BACKTRACE_SELF_TEST is not set -# CONFIG_FAULT_INJECTION is not set -# CONFIG_LATENCYTOP is not set -CONFIG_SYSCTL_SYSCALL_CHECK=y -CONFIG_HAVE_FTRACE=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -# CONFIG_FTRACE is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_SAMPLES is not set -CONFIG_HAVE_ARCH_KGDB=y -# CONFIG_KGDB is not set -# CONFIG_DEBUG_STACKOVERFLOW is not set -# CONFIG_DEBUG_STACK_USAGE is not set -# CONFIG_DEBUG_PAGEALLOC is not set -# CONFIG_CODE_PATCHING_SELFTEST is not set -# CONFIG_FTR_FIXUP_SELFTEST is not set -# CONFIG_XMON is not set -# CONFIG_IRQSTACKS is not set -# CONFIG_BDI_SWITCH is not set -# CONFIG_BOOTX_TEXT is not set -# CONFIG_PPC_EARLY_DEBUG is not set - -# -# Security options -# -# CONFIG_KEYS is not set -# CONFIG_SECURITY is not set -# CONFIG_SECURITY_FILE_CAPABILITIES is not set -CONFIG_CRYPTO=y - -# -# Crypto core or helper -# -# CONFIG_CRYPTO_MANAGER is not set -# CONFIG_CRYPTO_GF128MUL is not set -# CONFIG_CRYPTO_NULL is not set -# CONFIG_CRYPTO_CRYPTD is not set -# CONFIG_CRYPTO_AUTHENC is not set -# CONFIG_CRYPTO_TEST is not set - -# -# Authenticated Encryption with Associated Data -# -# CONFIG_CRYPTO_CCM is not set -# CONFIG_CRYPTO_GCM is not set -# CONFIG_CRYPTO_SEQIV is not set - -# -# Block modes -# -# CONFIG_CRYPTO_CBC is not set -# CONFIG_CRYPTO_CTR is not set -# CONFIG_CRYPTO_CTS is not set -# CONFIG_CRYPTO_ECB is not set -# CONFIG_CRYPTO_LRW is not set -# CONFIG_CRYPTO_PCBC is not set -# CONFIG_CRYPTO_XTS is not set - -# -# Hash modes -# -# CONFIG_CRYPTO_HMAC is not set -# CONFIG_CRYPTO_XCBC is not set - -# -# Digest -# -# CONFIG_CRYPTO_CRC32C is not set -# CONFIG_CRYPTO_MD4 is not set -# CONFIG_CRYPTO_MD5 is not set -# CONFIG_CRYPTO_MICHAEL_MIC is not set -# CONFIG_CRYPTO_RMD128 is not set -# CONFIG_CRYPTO_RMD160 is not set -# CONFIG_CRYPTO_RMD256 is not set -# CONFIG_CRYPTO_RMD320 is not set -# CONFIG_CRYPTO_SHA1 is not set -# CONFIG_CRYPTO_SHA256 is not set -# CONFIG_CRYPTO_SHA512 is not set -# CONFIG_CRYPTO_TGR192 is not set -# CONFIG_CRYPTO_WP512 is not set - -# -# Ciphers -# -# CONFIG_CRYPTO_AES is not set -# CONFIG_CRYPTO_ANUBIS is not set -# CONFIG_CRYPTO_ARC4 is not set -# CONFIG_CRYPTO_BLOWFISH is not set -# CONFIG_CRYPTO_CAMELLIA is not set -# CONFIG_CRYPTO_CAST5 is not set -# CONFIG_CRYPTO_CAST6 is not set -# CONFIG_CRYPTO_DES is not set -# CONFIG_CRYPTO_FCRYPT is not set -# CONFIG_CRYPTO_KHAZAD is not set -# CONFIG_CRYPTO_SALSA20 is not set -# CONFIG_CRYPTO_SEED is not set -# CONFIG_CRYPTO_SERPENT is not set -# CONFIG_CRYPTO_TEA is not set -# CONFIG_CRYPTO_TWOFISH is not set - -# -# Compression -# -# CONFIG_CRYPTO_DEFLATE is not set -# CONFIG_CRYPTO_LZO is not set -CONFIG_CRYPTO_HW=y -# CONFIG_CRYPTO_DEV_HIFN_795X is not set -# CONFIG_CRYPTO_DEV_TALITOS is not set -# CONFIG_PPC_CLOCK is not set -CONFIG_PPC_LIB_RHEAP=y -# CONFIG_VIRTUALIZATION is not set diff --git a/arch/powerpc/configs/mpc8641_hpcn_defconfig b/arch/powerpc/configs/mpc8641_hpcn_defconfig deleted file mode 100644 index ea09be31b6e..00000000000 --- a/arch/powerpc/configs/mpc8641_hpcn_defconfig +++ /dev/null @@ -1,1666 +0,0 @@ -# -# Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc4 -# Thu Aug 21 00:52:11 2008 -# -# CONFIG_PPC64 is not set - -# -# Processor support -# -CONFIG_6xx=y -# CONFIG_PPC_85xx is not set -# CONFIG_PPC_8xx is not set -# CONFIG_40x is not set -# CONFIG_44x is not set -# CONFIG_E200 is not set -CONFIG_PPC_FPU=y -CONFIG_ALTIVEC=y -CONFIG_PPC_STD_MMU=y -CONFIG_PPC_STD_MMU_32=y -# CONFIG_PPC_MM_SLICES is not set -CONFIG_SMP=y -CONFIG_NR_CPUS=2 -CONFIG_PPC32=y -CONFIG_WORD_SIZE=32 -CONFIG_PPC_MERGE=y -CONFIG_MMU=y -CONFIG_GENERIC_CMOS_UPDATE=y -CONFIG_GENERIC_TIME=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_HARDIRQS=y -# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set -CONFIG_IRQ_PER_CPU=y -CONFIG_STACKTRACE_SUPPORT=y -CONFIG_HAVE_LATENCYTOP_SUPPORT=y -CONFIG_LOCKDEP_SUPPORT=y -CONFIG_RWSEM_XCHGADD_ALGORITHM=y -CONFIG_ARCH_HAS_ILOG2_U32=y -CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_GENERIC_FIND_NEXT_BIT=y -# CONFIG_ARCH_NO_VIRT_TO_BUS is not set -CONFIG_PPC=y -CONFIG_EARLY_PRINTK=y -CONFIG_GENERIC_NVRAM=y -CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y -CONFIG_ARCH_MAY_HAVE_PC_FDC=y -CONFIG_PPC_OF=y -CONFIG_OF=y -CONFIG_PPC_UDBG_16550=y -CONFIG_GENERIC_TBSYNC=y -CONFIG_AUDIT_ARCH=y -CONFIG_GENERIC_BUG=y -CONFIG_DEFAULT_UIMAGE=y -# CONFIG_PPC_DCR_NATIVE is not set -# CONFIG_PPC_DCR_MMIO is not set -CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" - -# -# General setup -# -CONFIG_EXPERIMENTAL=y -CONFIG_LOCK_KERNEL=y -CONFIG_INIT_ENV_ARG_LIMIT=32 -CONFIG_LOCALVERSION="" -CONFIG_LOCALVERSION_AUTO=y -CONFIG_SWAP=y -CONFIG_SYSVIPC=y -CONFIG_SYSVIPC_SYSCTL=y -CONFIG_POSIX_MQUEUE=y -CONFIG_BSD_PROCESS_ACCT=y -# CONFIG_BSD_PROCESS_ACCT_V3 is not set -# CONFIG_TASKSTATS is not set -CONFIG_AUDIT=y -# CONFIG_AUDITSYSCALL is not set -CONFIG_IKCONFIG=y -CONFIG_IKCONFIG_PROC=y -CONFIG_LOG_BUF_SHIFT=14 -# CONFIG_CGROUPS is not set -CONFIG_GROUP_SCHED=y -# CONFIG_FAIR_GROUP_SCHED is not set -# CONFIG_RT_GROUP_SCHED is not set -CONFIG_USER_SCHED=y -# CONFIG_CGROUP_SCHED is not set -CONFIG_SYSFS_DEPRECATED=y -CONFIG_SYSFS_DEPRECATED_V2=y -# CONFIG_RELAY is not set -# CONFIG_NAMESPACES is not set -CONFIG_BLK_DEV_INITRD=y -CONFIG_INITRAMFS_SOURCE="" -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set -CONFIG_SYSCTL=y -CONFIG_EMBEDDED=y -CONFIG_SYSCTL_SYSCALL=y -CONFIG_KALLSYMS=y -CONFIG_KALLSYMS_ALL=y -CONFIG_KALLSYMS_EXTRA_PASS=y -CONFIG_HOTPLUG=y -CONFIG_PRINTK=y -CONFIG_BUG=y -CONFIG_ELF_CORE=y -CONFIG_PCSPKR_PLATFORM=y -CONFIG_COMPAT_BRK=y -CONFIG_BASE_FULL=y -CONFIG_FUTEX=y -CONFIG_ANON_INODES=y -CONFIG_EPOLL=y -CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y -CONFIG_EVENTFD=y -CONFIG_SHMEM=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_SLUB_DEBUG=y -# CONFIG_SLAB is not set -CONFIG_SLUB=y -# CONFIG_SLOB is not set -# CONFIG_PROFILING is not set -# CONFIG_MARKERS is not set -CONFIG_HAVE_OPROFILE=y -# CONFIG_KPROBES is not set -CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y -CONFIG_HAVE_IOREMAP_PROT=y -CONFIG_HAVE_KPROBES=y -CONFIG_HAVE_KRETPROBES=y -CONFIG_HAVE_ARCH_TRACEHOOK=y -# CONFIG_HAVE_DMA_ATTRS is not set -CONFIG_USE_GENERIC_SMP_HELPERS=y -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y -# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set -CONFIG_SLABINFO=y -CONFIG_RT_MUTEXES=y -# CONFIG_TINY_SHMEM is not set -CONFIG_BASE_SMALL=0 -CONFIG_MODULES=y -# CONFIG_MODULE_FORCE_LOAD is not set -CONFIG_MODULE_UNLOAD=y -CONFIG_MODULE_FORCE_UNLOAD=y -CONFIG_MODVERSIONS=y -# CONFIG_MODULE_SRCVERSION_ALL is not set -CONFIG_KMOD=y -CONFIG_STOP_MACHINE=y -CONFIG_BLOCK=y -CONFIG_LBD=y -# CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_LSF is not set -# CONFIG_BLK_DEV_BSG is not set -# CONFIG_BLK_DEV_INTEGRITY is not set - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y -# CONFIG_DEFAULT_AS is not set -# CONFIG_DEFAULT_DEADLINE is not set -CONFIG_DEFAULT_CFQ=y -# CONFIG_DEFAULT_NOOP is not set -CONFIG_DEFAULT_IOSCHED="cfq" -CONFIG_CLASSIC_RCU=y - -# -# Platform support -# -CONFIG_PPC_MULTIPLATFORM=y -CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y -# CONFIG_MPC5121_ADS is not set -# CONFIG_MPC5121_GENERIC is not set -# CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y -# CONFIG_PPC_CELL is not set -# CONFIG_PPC_CELL_NATIVE is not set -# CONFIG_PPC_82xx is not set -# CONFIG_PQ2ADS is not set -# CONFIG_PPC_83xx is not set -CONFIG_PPC_86xx=y -CONFIG_MPC8641_HPCN=y -# CONFIG_SBC8641D is not set -# CONFIG_MPC8610_HPCD is not set -CONFIG_MPC8641=y -CONFIG_PPC_NATIVE=y -# CONFIG_UDBG_RTAS_CONSOLE is not set -# CONFIG_IPIC is not set -CONFIG_MPIC=y -# CONFIG_MPIC_WEIRD is not set -CONFIG_PPC_I8259=y -CONFIG_PPC_RTAS=y -# CONFIG_RTAS_ERROR_LOGGING is not set -CONFIG_RTAS_PROC=y -# CONFIG_MMIO_NVRAM is not set -CONFIG_PPC_MPC106=y -# CONFIG_PPC_970_NAP is not set -# CONFIG_PPC_INDIRECT_IO is not set -# CONFIG_GENERIC_IOMAP is not set -# CONFIG_CPU_FREQ is not set -# CONFIG_PPC601_SYNC_FIX is not set -# CONFIG_TAU is not set -CONFIG_FSL_ULI1575=y - -# -# Kernel options -# -CONFIG_HIGHMEM=y -CONFIG_TICK_ONESHOT=y -CONFIG_NO_HZ=y -CONFIG_HIGH_RES_TIMERS=y -CONFIG_GENERIC_CLOCKEVENTS_BUILD=y -# CONFIG_HZ_100 is not set -# CONFIG_HZ_250 is not set -# CONFIG_HZ_300 is not set -CONFIG_HZ_1000=y -CONFIG_HZ=1000 -CONFIG_SCHED_HRTICK=y -CONFIG_PREEMPT_NONE=y -# CONFIG_PREEMPT_VOLUNTARY is not set -# CONFIG_PREEMPT is not set -CONFIG_BINFMT_ELF=y -CONFIG_BINFMT_MISC=m -# CONFIG_IOMMU_HELPER is not set -# CONFIG_HOTPLUG_CPU is not set -CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y -CONFIG_ARCH_HAS_WALK_MEMORY=y -CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y -# CONFIG_KEXEC is not set -# CONFIG_IRQ_ALL_CPUS is not set -CONFIG_ARCH_FLATMEM_ENABLE=y -CONFIG_ARCH_POPULATES_NODE_MAP=y -CONFIG_SELECT_MEMORY_MODEL=y -CONFIG_FLATMEM_MANUAL=y -# CONFIG_DISCONTIGMEM_MANUAL is not set -# CONFIG_SPARSEMEM_MANUAL is not set -CONFIG_FLATMEM=y -CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set -CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_SPLIT_PTLOCK_CPUS=4 -CONFIG_MIGRATION=y -# CONFIG_RESOURCES_64BIT is not set -CONFIG_ZONE_DMA_FLAG=1 -CONFIG_BOUNCE=y -CONFIG_VIRT_TO_BUS=y -CONFIG_FORCE_MAX_ZONEORDER=11 -CONFIG_PROC_DEVICETREE=y -# CONFIG_CMDLINE_BOOL is not set -CONFIG_EXTRA_TARGETS="" -# CONFIG_PM is not set -CONFIG_SECCOMP=y -CONFIG_ISA_DMA_API=y - -# -# Bus options -# -# CONFIG_ISA is not set -CONFIG_ZONE_DMA=y -CONFIG_GENERIC_ISA_DMA=y -CONFIG_PPC_INDIRECT_PCI=y -CONFIG_FSL_SOC=y -CONFIG_FSL_PCI=y -CONFIG_PPC_PCI_CHOICE=y -CONFIG_PCI=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_SYSCALL=y -# CONFIG_PCIEPORTBUS is not set -CONFIG_ARCH_SUPPORTS_MSI=y -# CONFIG_PCI_MSI is not set -CONFIG_PCI_LEGACY=y -# CONFIG_PCI_DEBUG is not set -# CONFIG_PCCARD is not set -# CONFIG_HOTPLUG_PCI is not set -CONFIG_HAS_RAPIDIO=y -# CONFIG_RAPIDIO is not set - -# -# Advanced setup -# -# CONFIG_ADVANCED_OPTIONS is not set - -# -# Default settings for advanced configuration options are used -# -CONFIG_LOWMEM_SIZE=0x30000000 -CONFIG_PAGE_OFFSET=0xc0000000 -CONFIG_KERNEL_START=0xc0000000 -CONFIG_PHYSICAL_START=0x00000000 -CONFIG_TASK_SIZE=0xc0000000 -CONFIG_NET=y - -# -# Networking options -# -CONFIG_PACKET=y -# CONFIG_PACKET_MMAP is not set -CONFIG_UNIX=y -CONFIG_XFRM=y -CONFIG_XFRM_USER=y -# CONFIG_XFRM_SUB_POLICY is not set -# CONFIG_XFRM_MIGRATE is not set -# CONFIG_XFRM_STATISTICS is not set -CONFIG_NET_KEY=m -# CONFIG_NET_KEY_MIGRATE is not set -CONFIG_INET=y -CONFIG_IP_MULTICAST=y -CONFIG_IP_ADVANCED_ROUTER=y -CONFIG_ASK_IP_FIB_HASH=y -# CONFIG_IP_FIB_TRIE is not set -CONFIG_IP_FIB_HASH=y -CONFIG_IP_MULTIPLE_TABLES=y -CONFIG_IP_ROUTE_MULTIPATH=y -CONFIG_IP_ROUTE_VERBOSE=y -CONFIG_IP_PNP=y -CONFIG_IP_PNP_DHCP=y -CONFIG_IP_PNP_BOOTP=y -CONFIG_IP_PNP_RARP=y -CONFIG_NET_IPIP=y -CONFIG_NET_IPGRE=y -CONFIG_NET_IPGRE_BROADCAST=y -CONFIG_IP_MROUTE=y -CONFIG_IP_PIMSM_V1=y -CONFIG_IP_PIMSM_V2=y -CONFIG_ARPD=y -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_XFRM_TUNNEL is not set -CONFIG_INET_TUNNEL=y -# CONFIG_INET_XFRM_MODE_TRANSPORT is not set -# CONFIG_INET_XFRM_MODE_TUNNEL is not set -# CONFIG_INET_XFRM_MODE_BEET is not set -# CONFIG_INET_LRO is not set -CONFIG_INET_DIAG=y -CONFIG_INET_TCP_DIAG=y -# CONFIG_TCP_CONG_ADVANCED is not set -CONFIG_TCP_CONG_CUBIC=y -CONFIG_DEFAULT_TCP_CONG="cubic" -# CONFIG_TCP_MD5SIG is not set -CONFIG_IPV6=y -# CONFIG_IPV6_PRIVACY is not set -# CONFIG_IPV6_ROUTER_PREF is not set -# CONFIG_IPV6_OPTIMISTIC_DAD is not set -# CONFIG_INET6_AH is not set -# CONFIG_INET6_ESP is not set -# CONFIG_INET6_IPCOMP is not set -# CONFIG_IPV6_MIP6 is not set -# CONFIG_INET6_XFRM_TUNNEL is not set -# CONFIG_INET6_TUNNEL is not set -CONFIG_INET6_XFRM_MODE_TRANSPORT=y -CONFIG_INET6_XFRM_MODE_TUNNEL=y -CONFIG_INET6_XFRM_MODE_BEET=y -# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set -CONFIG_IPV6_SIT=y -CONFIG_IPV6_NDISC_NODETYPE=y -# CONFIG_IPV6_TUNNEL is not set -# CONFIG_IPV6_MULTIPLE_TABLES is not set -# CONFIG_IPV6_MROUTE is not set -# CONFIG_NETWORK_SECMARK is not set -# CONFIG_NETFILTER is not set -# CONFIG_IP_DCCP is not set -CONFIG_IP_SCTP=m -# CONFIG_SCTP_DBG_MSG is not set -# CONFIG_SCTP_DBG_OBJCNT is not set -# CONFIG_SCTP_HMAC_NONE is not set -# CONFIG_SCTP_HMAC_SHA1 is not set -CONFIG_SCTP_HMAC_MD5=y -# CONFIG_TIPC is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set -# CONFIG_NET_SCHED is not set - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_HAMRADIO is not set -# CONFIG_CAN is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set -# CONFIG_AF_RXRPC is not set -CONFIG_FIB_RULES=y - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set -# CONFIG_RFKILL is not set -# CONFIG_NET_9P is not set - -# -# Device Drivers -# - -# -# Generic Driver Options -# -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" -CONFIG_STANDALONE=y -CONFIG_PREVENT_FIRMWARE_BUILD=y -CONFIG_FW_LOADER=y -CONFIG_FIRMWARE_IN_KERNEL=y -CONFIG_EXTRA_FIRMWARE="" -# CONFIG_DEBUG_DRIVER is not set -# CONFIG_DEBUG_DEVRES is not set -# CONFIG_SYS_HYPERVISOR is not set -# CONFIG_CONNECTOR is not set -# CONFIG_MTD is not set -CONFIG_OF_DEVICE=y -CONFIG_OF_I2C=y -# CONFIG_PARPORT is not set -CONFIG_BLK_DEV=y -# CONFIG_BLK_DEV_FD is not set -# CONFIG_MAC_FLOPPY is not set -# CONFIG_BLK_CPQ_DA is not set -# CONFIG_BLK_CPQ_CISS_DA is not set -# CONFIG_BLK_DEV_DAC960 is not set -# CONFIG_BLK_DEV_UMEM is not set -# CONFIG_BLK_DEV_COW_COMMON is not set -CONFIG_BLK_DEV_LOOP=y -# CONFIG_BLK_DEV_CRYPTOLOOP is not set -CONFIG_BLK_DEV_NBD=y -# CONFIG_BLK_DEV_SX8 is not set -# CONFIG_BLK_DEV_UB is not set -CONFIG_BLK_DEV_RAM=y -CONFIG_BLK_DEV_RAM_COUNT=16 -CONFIG_BLK_DEV_RAM_SIZE=131072 -# CONFIG_BLK_DEV_XIP is not set -# CONFIG_CDROM_PKTCDVD is not set -# CONFIG_ATA_OVER_ETH is not set -# CONFIG_BLK_DEV_HD is not set -CONFIG_MISC_DEVICES=y -# CONFIG_PHANTOM is not set -# CONFIG_EEPROM_93CX6 is not set -# CONFIG_SGI_IOC4 is not set -# CONFIG_TIFM_CORE is not set -# CONFIG_ENCLOSURE_SERVICES is not set -# CONFIG_HP_ILO is not set -CONFIG_HAVE_IDE=y -# CONFIG_IDE is not set - -# -# SCSI device support -# -# CONFIG_RAID_ATTRS is not set -CONFIG_SCSI=y -CONFIG_SCSI_DMA=y -# CONFIG_SCSI_TGT is not set -# CONFIG_SCSI_NETLINK is not set -CONFIG_SCSI_PROC_FS=y - -# -# SCSI support type (disk, tape, CD-ROM) -# -CONFIG_BLK_DEV_SD=y -CONFIG_CHR_DEV_ST=y -# CONFIG_CHR_DEV_OSST is not set -CONFIG_BLK_DEV_SR=y -# CONFIG_BLK_DEV_SR_VENDOR is not set -CONFIG_CHR_DEV_SG=y -# CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# -CONFIG_SCSI_MULTI_LUN=y -# CONFIG_SCSI_CONSTANTS is not set -CONFIG_SCSI_LOGGING=y -# CONFIG_SCSI_SCAN_ASYNC is not set -CONFIG_SCSI_WAIT_SCAN=m - -# -# SCSI Transports -# -# CONFIG_SCSI_SPI_ATTRS is not set -# CONFIG_SCSI_FC_ATTRS is not set -# CONFIG_SCSI_ISCSI_ATTRS is not set -# CONFIG_SCSI_SAS_LIBSAS is not set -# CONFIG_SCSI_SRP_ATTRS is not set -CONFIG_SCSI_LOWLEVEL=y -# CONFIG_ISCSI_TCP is not set -# CONFIG_BLK_DEV_3W_XXXX_RAID is not set -# CONFIG_SCSI_3W_9XXX is not set -# CONFIG_SCSI_ACARD is not set -# CONFIG_SCSI_AACRAID is not set -# CONFIG_SCSI_AIC7XXX is not set -# CONFIG_SCSI_AIC7XXX_OLD is not set -# CONFIG_SCSI_AIC79XX is not set -# CONFIG_SCSI_AIC94XX is not set -# CONFIG_SCSI_DPT_I2O is not set -# CONFIG_SCSI_ADVANSYS is not set -# CONFIG_SCSI_ARCMSR is not set -# CONFIG_MEGARAID_NEWGEN is not set -# CONFIG_MEGARAID_LEGACY is not set -# CONFIG_MEGARAID_SAS is not set -# CONFIG_SCSI_HPTIOP is not set -# CONFIG_SCSI_BUSLOGIC is not set -# CONFIG_SCSI_DMX3191D is not set -# CONFIG_SCSI_EATA is not set -# CONFIG_SCSI_FUTURE_DOMAIN is not set -# CONFIG_SCSI_GDTH is not set -# CONFIG_SCSI_IPS is not set -# CONFIG_SCSI_INITIO is not set -# CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set -# CONFIG_SCSI_STEX is not set -# CONFIG_SCSI_SYM53C8XX_2 is not set -# CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_1280 is not set -# CONFIG_SCSI_QLA_FC is not set -# CONFIG_SCSI_QLA_ISCSI is not set -# CONFIG_SCSI_LPFC is not set -# CONFIG_SCSI_DC395x is not set -# CONFIG_SCSI_DC390T is not set -# CONFIG_SCSI_NSP32 is not set -# CONFIG_SCSI_DEBUG is not set -# CONFIG_SCSI_MESH is not set -# CONFIG_SCSI_MAC53C94 is not set -# CONFIG_SCSI_SRP is not set -# CONFIG_SCSI_DH is not set -CONFIG_ATA=y -# CONFIG_ATA_NONSTANDARD is not set -CONFIG_SATA_PMP=y -CONFIG_SATA_AHCI=y -# CONFIG_SATA_SIL24 is not set -# CONFIG_SATA_FSL is not set -CONFIG_ATA_SFF=y -# CONFIG_SATA_SVW is not set -# CONFIG_ATA_PIIX is not set -# CONFIG_SATA_MV is not set -# CONFIG_SATA_NV is not set -# CONFIG_PDC_ADMA is not set -# CONFIG_SATA_QSTOR is not set -# CONFIG_SATA_PROMISE is not set -# CONFIG_SATA_SX4 is not set -# CONFIG_SATA_SIL is not set -# CONFIG_SATA_SIS is not set -# CONFIG_SATA_ULI is not set -# CONFIG_SATA_VIA is not set -# CONFIG_SATA_VITESSE is not set -# CONFIG_SATA_INIC162X is not set -CONFIG_PATA_ALI=y -# CONFIG_PATA_AMD is not set -# CONFIG_PATA_ARTOP is not set -# CONFIG_PATA_ATIIXP is not set -# CONFIG_PATA_CMD640_PCI is not set -# CONFIG_PATA_CMD64X is not set -# CONFIG_PATA_CS5520 is not set -# CONFIG_PATA_CS5530 is not set -# CONFIG_PATA_CYPRESS is not set -# CONFIG_PATA_EFAR is not set -# CONFIG_ATA_GENERIC is not set -# CONFIG_PATA_HPT366 is not set -# CONFIG_PATA_HPT37X is not set -# CONFIG_PATA_HPT3X2N is not set -# CONFIG_PATA_HPT3X3 is not set -# CONFIG_PATA_IT821X is not set -# CONFIG_PATA_IT8213 is not set -# CONFIG_PATA_JMICRON is not set -# CONFIG_PATA_TRIFLEX is not set -# CONFIG_PATA_MARVELL is not set -# CONFIG_PATA_MPIIX is not set -# CONFIG_PATA_OLDPIIX is not set -# CONFIG_PATA_NETCELL is not set -# CONFIG_PATA_NINJA32 is not set -# CONFIG_PATA_NS87410 is not set -# CONFIG_PATA_NS87415 is not set -# CONFIG_PATA_OPTI is not set -# CONFIG_PATA_OPTIDMA is not set -# CONFIG_PATA_PDC_OLD is not set -# CONFIG_PATA_RADISYS is not set -# CONFIG_PATA_RZ1000 is not set -# CONFIG_PATA_SC1200 is not set -# CONFIG_PATA_SERVERWORKS is not set -# CONFIG_PATA_PDC2027X is not set -# CONFIG_PATA_SIL680 is not set -# CONFIG_PATA_SIS is not set -# CONFIG_PATA_VIA is not set -# CONFIG_PATA_WINBOND is not set -# CONFIG_PATA_PLATFORM is not set -# CONFIG_PATA_SCH is not set -# CONFIG_MD is not set -# CONFIG_FUSION is not set - -# -# IEEE 1394 (FireWire) support -# - -# -# Enable only one of the two stacks, unless you know what you are doing -# -# CONFIG_FIREWIRE is not set -# CONFIG_IEEE1394 is not set -# CONFIG_I2O is not set -# CONFIG_MACINTOSH_DRIVERS is not set -CONFIG_NETDEVICES=y -CONFIG_DUMMY=y -# CONFIG_BONDING is not set -# CONFIG_MACVLAN is not set -# CONFIG_EQUALIZER is not set -# CONFIG_TUN is not set -# CONFIG_VETH is not set -# CONFIG_ARCNET is not set -CONFIG_PHYLIB=y - -# -# MII PHY device drivers -# -# CONFIG_MARVELL_PHY is not set -# CONFIG_DAVICOM_PHY is not set -# CONFIG_QSEMI_PHY is not set -# CONFIG_LXT_PHY is not set -# CONFIG_CICADA_PHY is not set -CONFIG_VITESSE_PHY=y -# CONFIG_SMSC_PHY is not set -# CONFIG_BROADCOM_PHY is not set -# CONFIG_ICPLUS_PHY is not set -# CONFIG_REALTEK_PHY is not set -# CONFIG_FIXED_PHY is not set -# CONFIG_MDIO_BITBANG is not set -CONFIG_NET_ETHERNET=y -CONFIG_MII=y -# CONFIG_MACE is not set -# CONFIG_BMAC is not set -# CONFIG_HAPPYMEAL is not set -# CONFIG_SUNGEM is not set -# CONFIG_CASSINI is not set -# CONFIG_NET_VENDOR_3COM is not set -# CONFIG_NET_TULIP is not set -# CONFIG_HP100 is not set -# CONFIG_IBM_NEW_EMAC_ZMII is not set -# CONFIG_IBM_NEW_EMAC_RGMII is not set -# CONFIG_IBM_NEW_EMAC_TAH is not set -# CONFIG_IBM_NEW_EMAC_EMAC4 is not set -# CONFIG_NET_PCI is not set -# CONFIG_B44 is not set -CONFIG_NETDEV_1000=y -# CONFIG_ACENIC is not set -# CONFIG_DL2K is not set -# CONFIG_E1000 is not set -# CONFIG_E1000E is not set -# CONFIG_IP1000 is not set -# CONFIG_IGB is not set -# CONFIG_NS83820 is not set -# CONFIG_HAMACHI is not set -# CONFIG_YELLOWFIN is not set -# CONFIG_R8169 is not set -# CONFIG_SIS190 is not set -# CONFIG_SKGE is not set -# CONFIG_SKY2 is not set -# CONFIG_VIA_VELOCITY is not set -# CONFIG_TIGON3 is not set -# CONFIG_BNX2 is not set -CONFIG_GIANFAR=y -# CONFIG_MV643XX_ETH is not set -# CONFIG_QLA3XXX is not set -# CONFIG_ATL1 is not set -# CONFIG_ATL1E is not set -CONFIG_NETDEV_10000=y -# CONFIG_CHELSIO_T1 is not set -# CONFIG_CHELSIO_T3 is not set -# CONFIG_IXGBE is not set -# CONFIG_IXGB is not set -# CONFIG_S2IO is not set -# CONFIG_MYRI10GE is not set -# CONFIG_NETXEN_NIC is not set -# CONFIG_NIU is not set -# CONFIG_MLX4_CORE is not set -# CONFIG_TEHUTI is not set -# CONFIG_BNX2X is not set -# CONFIG_SFC is not set -# CONFIG_TR is not set - -# -# Wireless LAN -# -# CONFIG_WLAN_PRE80211 is not set -# CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI_LEDS is not set - -# -# USB Network Adapters -# -# CONFIG_USB_CATC is not set -# CONFIG_USB_KAWETH is not set -# CONFIG_USB_PEGASUS is not set -# CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET is not set -# CONFIG_WAN is not set -# CONFIG_FDDI is not set -# CONFIG_HIPPI is not set -# CONFIG_PPP is not set -# CONFIG_SLIP is not set -# CONFIG_NET_FC is not set -# CONFIG_NETCONSOLE is not set -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set -# CONFIG_ISDN is not set -# CONFIG_PHONE is not set - -# -# Input device support -# -CONFIG_INPUT=y -# CONFIG_INPUT_FF_MEMLESS is not set -# CONFIG_INPUT_POLLDEV is not set - -# -# Userland interfaces -# -# CONFIG_INPUT_MOUSEDEV is not set -# CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_EVDEV is not set -# CONFIG_INPUT_EVBUG is not set - -# -# Input Device Drivers -# -# CONFIG_INPUT_KEYBOARD is not set -# CONFIG_INPUT_MOUSE is not set -# CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TABLET is not set -# CONFIG_INPUT_TOUCHSCREEN is not set -# CONFIG_INPUT_MISC is not set - -# -# Hardware I/O ports -# -CONFIG_SERIO=y -CONFIG_SERIO_I8042=y -CONFIG_SERIO_SERPORT=y -# CONFIG_SERIO_PCIPS2 is not set -CONFIG_SERIO_LIBPS2=y -# CONFIG_SERIO_RAW is not set -# CONFIG_SERIO_XILINX_XPS_PS2 is not set -# CONFIG_GAMEPORT is not set - -# -# Character devices -# -CONFIG_VT=y -CONFIG_CONSOLE_TRANSLATIONS=y -CONFIG_VT_CONSOLE=y -CONFIG_HW_CONSOLE=y -# CONFIG_VT_HW_CONSOLE_BINDING is not set -CONFIG_DEVKMEM=y -# CONFIG_SERIAL_NONSTANDARD is not set -# CONFIG_NOZOMI is not set - -# -# Serial drivers -# -CONFIG_SERIAL_8250=y -CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_PCI=y -CONFIG_SERIAL_8250_NR_UARTS=2 -CONFIG_SERIAL_8250_RUNTIME_UARTS=2 -CONFIG_SERIAL_8250_EXTENDED=y -CONFIG_SERIAL_8250_MANY_PORTS=y -CONFIG_SERIAL_8250_SHARE_IRQ=y -CONFIG_SERIAL_8250_DETECT_IRQ=y -CONFIG_SERIAL_8250_RSA=y - -# -# Non-8250 serial port support -# -# CONFIG_SERIAL_UARTLITE is not set -CONFIG_SERIAL_CORE=y -CONFIG_SERIAL_CORE_CONSOLE=y -# CONFIG_SERIAL_PMACZILOG is not set -# CONFIG_SERIAL_JSM is not set -# CONFIG_SERIAL_OF_PLATFORM is not set -CONFIG_UNIX98_PTYS=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 -# CONFIG_BRIQ_PANEL is not set -# CONFIG_HVC_RTAS is not set -# CONFIG_IPMI_HANDLER is not set -# CONFIG_HW_RANDOM is not set -CONFIG_NVRAM=y -# CONFIG_R3964 is not set -# CONFIG_APPLICOM is not set -# CONFIG_RAW_DRIVER is not set -# CONFIG_TCG_TPM is not set -CONFIG_DEVPORT=y -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -# CONFIG_I2C_CHARDEV is not set -CONFIG_I2C_HELPER_AUTO=y - -# -# I2C Hardware Bus support -# - -# -# PC SMBus host controller drivers -# -# CONFIG_I2C_ALI1535 is not set -# CONFIG_I2C_ALI1563 is not set -# CONFIG_I2C_ALI15X3 is not set -# CONFIG_I2C_AMD756 is not set -# CONFIG_I2C_AMD8111 is not set -# CONFIG_I2C_I801 is not set -# CONFIG_I2C_ISCH is not set -# CONFIG_I2C_PIIX4 is not set -# CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_SIS5595 is not set -# CONFIG_I2C_SIS630 is not set -# CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_VIA is not set -# CONFIG_I2C_VIAPRO is not set - -# -# Mac SMBus host controller drivers -# -# CONFIG_I2C_HYDRA is not set -CONFIG_I2C_POWERMAC=y - -# -# I2C system bus drivers (mostly embedded / system-on-chip) -# -CONFIG_I2C_MPC=y -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_SIMTEC is not set - -# -# External I2C/SMBus adapter drivers -# -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_TINY_USB is not set - -# -# Graphics adapter I2C/DDC channel drivers -# -# CONFIG_I2C_VOODOO3 is not set - -# -# Other I2C/SMBus bus drivers -# -# CONFIG_I2C_PCA_PLATFORM is not set -# CONFIG_I2C_STUB is not set - -# -# Miscellaneous I2C Chip support -# -# CONFIG_DS1682 is not set -# CONFIG_AT24 is not set -CONFIG_SENSORS_EEPROM=y -# CONFIG_SENSORS_PCF8574 is not set -# CONFIG_PCF8575 is not set -# CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_MAX6875 is not set -# CONFIG_SENSORS_TSL2550 is not set -# CONFIG_I2C_DEBUG_CORE is not set -# CONFIG_I2C_DEBUG_ALGO is not set -# CONFIG_I2C_DEBUG_BUS is not set -# CONFIG_I2C_DEBUG_CHIP is not set -# CONFIG_SPI is not set -CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y -# CONFIG_GPIOLIB is not set -# CONFIG_W1 is not set -# CONFIG_POWER_SUPPLY is not set -# CONFIG_HWMON is not set -# CONFIG_THERMAL is not set -# CONFIG_THERMAL_HWMON is not set -# CONFIG_WATCHDOG is not set - -# -# Sonics Silicon Backplane -# -CONFIG_SSB_POSSIBLE=y -# CONFIG_SSB is not set - -# -# Multifunction device drivers -# -# CONFIG_MFD_CORE is not set -# CONFIG_MFD_SM501 is not set -# CONFIG_HTC_PASIC3 is not set -# CONFIG_MFD_TMIO is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -CONFIG_DVB_CORE=m -CONFIG_VIDEO_MEDIA=m - -# -# Multimedia drivers -# -# CONFIG_MEDIA_ATTACH is not set -CONFIG_MEDIA_TUNER=m -# CONFIG_MEDIA_TUNER_CUSTOMIZE is not set -CONFIG_MEDIA_TUNER_SIMPLE=m -CONFIG_MEDIA_TUNER_TDA8290=m -CONFIG_MEDIA_TUNER_TDA9887=m -CONFIG_MEDIA_TUNER_TEA5761=m -CONFIG_MEDIA_TUNER_TEA5767=m -CONFIG_MEDIA_TUNER_MT20XX=m -CONFIG_MEDIA_TUNER_XC2028=m -CONFIG_MEDIA_TUNER_XC5000=m -CONFIG_DVB_CAPTURE_DRIVERS=y - -# -# Supported SAA7146 based PCI Adapters -# -# CONFIG_TTPCI_EEPROM is not set -# CONFIG_DVB_BUDGET_CORE is not set - -# -# Supported USB Adapters -# -# CONFIG_DVB_USB is not set -# CONFIG_DVB_TTUSB_BUDGET is not set -# CONFIG_DVB_TTUSB_DEC is not set -# CONFIG_DVB_CINERGYT2 is not set -# CONFIG_DVB_SIANO_SMS1XXX is not set - -# -# Supported FlexCopII (B2C2) Adapters -# -# CONFIG_DVB_B2C2_FLEXCOP is not set - -# -# Supported BT878 Adapters -# - -# -# Supported Pluto2 Adapters -# -# CONFIG_DVB_PLUTO2 is not set - -# -# Supported DVB Frontends -# - -# -# Customise DVB Frontends -# -# CONFIG_DVB_FE_CUSTOMISE is not set - -# -# DVB-S (satellite) frontends -# -# CONFIG_DVB_CX24110 is not set -# CONFIG_DVB_CX24123 is not set -# CONFIG_DVB_MT312 is not set -# CONFIG_DVB_S5H1420 is not set -# CONFIG_DVB_STV0299 is not set -# CONFIG_DVB_TDA8083 is not set -# CONFIG_DVB_TDA10086 is not set -# CONFIG_DVB_VES1X93 is not set -# CONFIG_DVB_TUNER_ITD1000 is not set -# CONFIG_DVB_TDA826X is not set -# CONFIG_DVB_TUA6100 is not set - -# -# DVB-T (terrestrial) frontends -# -# CONFIG_DVB_SP8870 is not set -# CONFIG_DVB_SP887X is not set -# CONFIG_DVB_CX22700 is not set -# CONFIG_DVB_CX22702 is not set -# CONFIG_DVB_DRX397XD is not set -# CONFIG_DVB_L64781 is not set -# CONFIG_DVB_TDA1004X is not set -# CONFIG_DVB_NXT6000 is not set -# CONFIG_DVB_MT352 is not set -# CONFIG_DVB_ZL10353 is not set -# CONFIG_DVB_DIB3000MB is not set -# CONFIG_DVB_DIB3000MC is not set -# CONFIG_DVB_DIB7000M is not set -# CONFIG_DVB_DIB7000P is not set -# CONFIG_DVB_TDA10048 is not set - -# -# DVB-C (cable) frontends -# -# CONFIG_DVB_VES1820 is not set -# CONFIG_DVB_TDA10021 is not set -# CONFIG_DVB_TDA10023 is not set -# CONFIG_DVB_STV0297 is not set - -# -# ATSC (North American/Korean Terrestrial/Cable DTV) frontends -# -# CONFIG_DVB_NXT200X is not set -# CONFIG_DVB_OR51211 is not set -# CONFIG_DVB_OR51132 is not set -# CONFIG_DVB_BCM3510 is not set -# CONFIG_DVB_LGDT330X is not set -# CONFIG_DVB_S5H1409 is not set -# CONFIG_DVB_AU8522 is not set -# CONFIG_DVB_S5H1411 is not set - -# -# Digital terrestrial only tuners/PLL -# -# CONFIG_DVB_PLL is not set -# CONFIG_DVB_TUNER_DIB0070 is not set - -# -# SEC control devices for DVB-S -# -# CONFIG_DVB_LNBP21 is not set -# CONFIG_DVB_ISL6405 is not set -# CONFIG_DVB_ISL6421 is not set -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set - -# -# Graphics support -# -# CONFIG_AGP is not set -# CONFIG_DRM is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set - -# -# Display device support -# -# CONFIG_DISPLAY_SUPPORT is not set - -# -# Console display driver support -# -CONFIG_VGA_CONSOLE=y -# CONFIG_VGACON_SOFT_SCROLLBACK is not set -CONFIG_DUMMY_CONSOLE=y -CONFIG_SOUND=y -CONFIG_SND=y -CONFIG_SND_TIMER=y -CONFIG_SND_PCM=y -# CONFIG_SND_SEQUENCER is not set -CONFIG_SND_OSSEMUL=y -CONFIG_SND_MIXER_OSS=y -CONFIG_SND_PCM_OSS=y -CONFIG_SND_PCM_OSS_PLUGINS=y -# CONFIG_SND_DYNAMIC_MINORS is not set -# CONFIG_SND_SUPPORT_OLD_API is not set -CONFIG_SND_VERBOSE_PROCFS=y -# CONFIG_SND_VERBOSE_PRINTK is not set -# CONFIG_SND_DEBUG is not set -CONFIG_SND_VMASTER=y -CONFIG_SND_AC97_CODEC=y -CONFIG_SND_DRIVERS=y -# CONFIG_SND_DUMMY is not set -# CONFIG_SND_MTPAV is not set -# CONFIG_SND_SERIAL_U16550 is not set -# CONFIG_SND_MPU401 is not set -# CONFIG_SND_AC97_POWER_SAVE is not set -CONFIG_SND_PCI=y -# CONFIG_SND_AD1889 is not set -# CONFIG_SND_ALS300 is not set -# CONFIG_SND_ALS4000 is not set -# CONFIG_SND_ALI5451 is not set -# CONFIG_SND_ATIIXP is not set -# CONFIG_SND_ATIIXP_MODEM is not set -# CONFIG_SND_AU8810 is not set -# CONFIG_SND_AU8820 is not set -# CONFIG_SND_AU8830 is not set -# CONFIG_SND_AW2 is not set -# CONFIG_SND_AZT3328 is not set -# CONFIG_SND_BT87X is not set -# CONFIG_SND_CA0106 is not set -# CONFIG_SND_CMIPCI is not set -# CONFIG_SND_OXYGEN is not set -# CONFIG_SND_CS4281 is not set -# CONFIG_SND_CS46XX is not set -# CONFIG_SND_CS5530 is not set -# CONFIG_SND_DARLA20 is not set -# CONFIG_SND_GINA20 is not set -# CONFIG_SND_LAYLA20 is not set -# CONFIG_SND_DARLA24 is not set -# CONFIG_SND_GINA24 is not set -# CONFIG_SND_LAYLA24 is not set -# CONFIG_SND_MONA is not set -# CONFIG_SND_MIA is not set -# CONFIG_SND_ECHO3G is not set -# CONFIG_SND_INDIGO is not set -# CONFIG_SND_INDIGOIO is not set -# CONFIG_SND_INDIGODJ is not set -# CONFIG_SND_EMU10K1 is not set -# CONFIG_SND_EMU10K1X is not set -# CONFIG_SND_ENS1370 is not set -# CONFIG_SND_ENS1371 is not set -# CONFIG_SND_ES1938 is not set -# CONFIG_SND_ES1968 is not set -# CONFIG_SND_FM801 is not set -# CONFIG_SND_HDA_INTEL is not set -# CONFIG_SND_HDSP is not set -# CONFIG_SND_HDSPM is not set -# CONFIG_SND_HIFIER is not set -# CONFIG_SND_ICE1712 is not set -# CONFIG_SND_ICE1724 is not set -CONFIG_SND_INTEL8X0=y -# CONFIG_SND_INTEL8X0M is not set -# CONFIG_SND_KORG1212 is not set -# CONFIG_SND_MAESTRO3 is not set -# CONFIG_SND_MIXART is not set -# CONFIG_SND_NM256 is not set -# CONFIG_SND_PCXHR is not set -# CONFIG_SND_RIPTIDE is not set -# CONFIG_SND_RME32 is not set -# CONFIG_SND_RME96 is not set -# CONFIG_SND_RME9652 is not set -# CONFIG_SND_SONICVIBES is not set -# CONFIG_SND_TRIDENT is not set -# CONFIG_SND_VIA82XX is not set -# CONFIG_SND_VIA82XX_MODEM is not set -# CONFIG_SND_VIRTUOSO is not set -# CONFIG_SND_VX222 is not set -# CONFIG_SND_YMFPCI is not set -CONFIG_SND_PPC=y -# CONFIG_SND_POWERMAC is not set -# CONFIG_SND_AOA is not set -CONFIG_SND_USB=y -# CONFIG_SND_USB_AUDIO is not set -# CONFIG_SND_USB_USX2Y is not set -# CONFIG_SND_USB_CAIAQ is not set -# CONFIG_SND_SOC is not set -# CONFIG_SOUND_PRIME is not set -CONFIG_AC97_BUS=y -CONFIG_HID_SUPPORT=y -CONFIG_HID=y -# CONFIG_HID_DEBUG is not set -# CONFIG_HIDRAW is not set - -# -# USB Input Devices -# -CONFIG_USB_HID=y -# CONFIG_USB_HIDINPUT_POWERBOOK is not set -# CONFIG_HID_FF is not set -# CONFIG_USB_HIDDEV is not set -CONFIG_USB_SUPPORT=y -CONFIG_USB_ARCH_HAS_HCD=y -CONFIG_USB_ARCH_HAS_OHCI=y -CONFIG_USB_ARCH_HAS_EHCI=y -CONFIG_USB=y -# CONFIG_USB_DEBUG is not set -# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set - -# -# Miscellaneous USB options -# -CONFIG_USB_DEVICEFS=y -CONFIG_USB_DEVICE_CLASS=y -# CONFIG_USB_DYNAMIC_MINORS is not set -# CONFIG_USB_OTG is not set -# CONFIG_USB_OTG_WHITELIST is not set -# CONFIG_USB_OTG_BLACKLIST_HUB is not set -CONFIG_USB_MON=y - -# -# USB Host Controller Drivers -# -# CONFIG_USB_C67X00_HCD is not set -CONFIG_USB_EHCI_HCD=y -# CONFIG_USB_EHCI_ROOT_HUB_TT is not set -# CONFIG_USB_EHCI_TT_NEWSCHED is not set -# CONFIG_USB_EHCI_FSL is not set -CONFIG_USB_EHCI_HCD_PPC_OF=y -# CONFIG_USB_ISP116X_HCD is not set -# CONFIG_USB_ISP1760_HCD is not set -CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PPC_OF=y -CONFIG_USB_OHCI_HCD_PPC_OF_BE=y -CONFIG_USB_OHCI_HCD_PPC_OF_LE=y -CONFIG_USB_OHCI_HCD_PCI=y -CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y -CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y -CONFIG_USB_OHCI_LITTLE_ENDIAN=y -# CONFIG_USB_UHCI_HCD is not set -# CONFIG_USB_SL811_HCD is not set -# CONFIG_USB_R8A66597_HCD is not set - -# -# USB Device Class drivers -# -# CONFIG_USB_ACM is not set -# CONFIG_USB_PRINTER is not set -# CONFIG_USB_WDM is not set - -# -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' -# - -# -# may also be needed; see USB_STORAGE Help for more information -# -CONFIG_USB_STORAGE=y -# CONFIG_USB_STORAGE_DEBUG is not set -# CONFIG_USB_STORAGE_DATAFAB is not set -# CONFIG_USB_STORAGE_FREECOM is not set -# CONFIG_USB_STORAGE_ISD200 is not set -# CONFIG_USB_STORAGE_DPCM is not set -# CONFIG_USB_STORAGE_USBAT is not set -# CONFIG_USB_STORAGE_SDDR09 is not set -# CONFIG_USB_STORAGE_SDDR55 is not set -# CONFIG_USB_STORAGE_JUMPSHOT is not set -# CONFIG_USB_STORAGE_ALAUDA is not set -# CONFIG_USB_STORAGE_ONETOUCH is not set -# CONFIG_USB_STORAGE_KARMA is not set -# CONFIG_USB_STORAGE_SIERRA is not set -# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set -# CONFIG_USB_LIBUSUAL is not set - -# -# USB Imaging devices -# -# CONFIG_USB_MDC800 is not set -# CONFIG_USB_MICROTEK is not set - -# -# USB port drivers -# -# CONFIG_USB_SERIAL is not set - -# -# USB Miscellaneous drivers -# -# CONFIG_USB_EMI62 is not set -# CONFIG_USB_EMI26 is not set -# CONFIG_USB_ADUTUX is not set -# CONFIG_USB_RIO500 is not set -# CONFIG_USB_LEGOTOWER is not set -# CONFIG_USB_LCD is not set -# CONFIG_USB_BERRY_CHARGE is not set -# CONFIG_USB_LED is not set -# CONFIG_USB_CYPRESS_CY7C63 is not set -# CONFIG_USB_CYTHERM is not set -# CONFIG_USB_PHIDGET is not set -# CONFIG_USB_IDMOUSE is not set -# CONFIG_USB_FTDI_ELAN is not set -# CONFIG_USB_APPLEDISPLAY is not set -# CONFIG_USB_SISUSBVGA is not set -# CONFIG_USB_LD is not set -# CONFIG_USB_TRANCEVIBRATOR is not set -# CONFIG_USB_IOWARRIOR is not set -# CONFIG_USB_TEST is not set -# CONFIG_USB_ISIGHTFW is not set -# CONFIG_USB_GADGET is not set -# CONFIG_MMC is not set -# CONFIG_MEMSTICK is not set -# CONFIG_NEW_LEDS is not set -# CONFIG_ACCESSIBILITY is not set -# CONFIG_INFINIBAND is not set -# CONFIG_EDAC is not set -CONFIG_RTC_LIB=y -CONFIG_RTC_CLASS=y -CONFIG_RTC_HCTOSYS=y -CONFIG_RTC_HCTOSYS_DEVICE="rtc0" -# CONFIG_RTC_DEBUG is not set - -# -# RTC interfaces -# -CONFIG_RTC_INTF_SYSFS=y -CONFIG_RTC_INTF_PROC=y -CONFIG_RTC_INTF_DEV=y -# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set -# CONFIG_RTC_DRV_TEST is not set - -# -# I2C RTC drivers -# -# CONFIG_RTC_DRV_DS1307 is not set -# CONFIG_RTC_DRV_DS1374 is not set -# CONFIG_RTC_DRV_DS1672 is not set -# CONFIG_RTC_DRV_MAX6900 is not set -# CONFIG_RTC_DRV_RS5C372 is not set -# CONFIG_RTC_DRV_ISL1208 is not set -# CONFIG_RTC_DRV_X1205 is not set -# CONFIG_RTC_DRV_PCF8563 is not set -# CONFIG_RTC_DRV_PCF8583 is not set -# CONFIG_RTC_DRV_M41T80 is not set -# CONFIG_RTC_DRV_S35390A is not set -# CONFIG_RTC_DRV_FM3130 is not set - -# -# SPI RTC drivers -# - -# -# Platform RTC drivers -# -CONFIG_RTC_DRV_CMOS=y -# CONFIG_RTC_DRV_DS1511 is not set -# CONFIG_RTC_DRV_DS1553 is not set -# CONFIG_RTC_DRV_DS1742 is not set -# CONFIG_RTC_DRV_STK17TA8 is not set -# CONFIG_RTC_DRV_M48T86 is not set -# CONFIG_RTC_DRV_M48T59 is not set -# CONFIG_RTC_DRV_V3020 is not set - -# -# on-CPU RTC drivers -# -# CONFIG_RTC_DRV_PPC is not set -# CONFIG_DMADEVICES is not set -# CONFIG_UIO is not set - -# -# File systems -# -CONFIG_EXT2_FS=y -# CONFIG_EXT2_FS_XATTR is not set -# CONFIG_EXT2_FS_XIP is not set -CONFIG_EXT3_FS=y -CONFIG_EXT3_FS_XATTR=y -# CONFIG_EXT3_FS_POSIX_ACL is not set -# CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set -CONFIG_JBD=y -CONFIG_FS_MBCACHE=y -# CONFIG_REISERFS_FS is not set -# CONFIG_JFS_FS is not set -# CONFIG_FS_POSIX_ACL is not set -# CONFIG_XFS_FS is not set -# CONFIG_OCFS2_FS is not set -CONFIG_DNOTIFY=y -CONFIG_INOTIFY=y -CONFIG_INOTIFY_USER=y -# CONFIG_QUOTA is not set -# CONFIG_AUTOFS_FS is not set -# CONFIG_AUTOFS4_FS is not set -# CONFIG_FUSE_FS is not set - -# -# CD-ROM/DVD Filesystems -# -CONFIG_ISO9660_FS=m -CONFIG_JOLIET=y -CONFIG_ZISOFS=y -CONFIG_UDF_FS=m -CONFIG_UDF_NLS=y - -# -# DOS/FAT/NT Filesystems -# -CONFIG_FAT_FS=y -CONFIG_MSDOS_FS=m -CONFIG_VFAT_FS=y -CONFIG_FAT_DEFAULT_CODEPAGE=437 -CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" -CONFIG_NTFS_FS=y -# CONFIG_NTFS_DEBUG is not set -# CONFIG_NTFS_RW is not set - -# -# Pseudo filesystems -# -CONFIG_PROC_FS=y -CONFIG_PROC_KCORE=y -CONFIG_PROC_SYSCTL=y -CONFIG_SYSFS=y -CONFIG_TMPFS=y -# CONFIG_TMPFS_POSIX_ACL is not set -# CONFIG_HUGETLB_PAGE is not set -# CONFIG_CONFIGFS_FS is not set - -# -# Miscellaneous filesystems -# -CONFIG_ADFS_FS=m -# CONFIG_ADFS_FS_RW is not set -CONFIG_AFFS_FS=m -CONFIG_HFS_FS=m -CONFIG_HFSPLUS_FS=m -CONFIG_BEFS_FS=m -# CONFIG_BEFS_DEBUG is not set -CONFIG_BFS_FS=m -CONFIG_EFS_FS=m -CONFIG_CRAMFS=y -CONFIG_VXFS_FS=m -# CONFIG_MINIX_FS is not set -# CONFIG_OMFS_FS is not set -CONFIG_HPFS_FS=m -CONFIG_QNX4FS_FS=m -# CONFIG_ROMFS_FS is not set -CONFIG_SYSV_FS=m -CONFIG_UFS_FS=m -# CONFIG_UFS_FS_WRITE is not set -# CONFIG_UFS_DEBUG is not set -CONFIG_NETWORK_FILESYSTEMS=y -CONFIG_NFS_FS=y -CONFIG_NFS_V3=y -# CONFIG_NFS_V3_ACL is not set -CONFIG_NFS_V4=y -CONFIG_ROOT_NFS=y -CONFIG_NFSD=y -# CONFIG_NFSD_V3 is not set -# CONFIG_NFSD_V4 is not set -CONFIG_LOCKD=y -CONFIG_LOCKD_V4=y -CONFIG_EXPORTFS=y -CONFIG_NFS_COMMON=y -CONFIG_SUNRPC=y -CONFIG_SUNRPC_GSS=y -CONFIG_RPCSEC_GSS_KRB5=y -# CONFIG_RPCSEC_GSS_SPKM3 is not set -# CONFIG_SMB_FS is not set -# CONFIG_CIFS is not set -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_AFS_FS is not set - -# -# Partition Types -# -CONFIG_PARTITION_ADVANCED=y -# CONFIG_ACORN_PARTITION is not set -# CONFIG_OSF_PARTITION is not set -# CONFIG_AMIGA_PARTITION is not set -# CONFIG_ATARI_PARTITION is not set -CONFIG_MAC_PARTITION=y -CONFIG_MSDOS_PARTITION=y -# CONFIG_BSD_DISKLABEL is not set -# CONFIG_MINIX_SUBPARTITION is not set -# CONFIG_SOLARIS_X86_PARTITION is not set -# CONFIG_UNIXWARE_DISKLABEL is not set -# CONFIG_LDM_PARTITION is not set -# CONFIG_SGI_PARTITION is not set -# CONFIG_ULTRIX_PARTITION is not set -# CONFIG_SUN_PARTITION is not set -# CONFIG_KARMA_PARTITION is not set -# CONFIG_EFI_PARTITION is not set -# CONFIG_SYSV68_PARTITION is not set -CONFIG_NLS=y -CONFIG_NLS_DEFAULT="iso8859-1" -# CONFIG_NLS_CODEPAGE_437 is not set -# CONFIG_NLS_CODEPAGE_737 is not set -# CONFIG_NLS_CODEPAGE_775 is not set -# CONFIG_NLS_CODEPAGE_850 is not set -# CONFIG_NLS_CODEPAGE_852 is not set -# CONFIG_NLS_CODEPAGE_855 is not set -# CONFIG_NLS_CODEPAGE_857 is not set -# CONFIG_NLS_CODEPAGE_860 is not set -# CONFIG_NLS_CODEPAGE_861 is not set -# CONFIG_NLS_CODEPAGE_862 is not set -# CONFIG_NLS_CODEPAGE_863 is not set -# CONFIG_NLS_CODEPAGE_864 is not set -# CONFIG_NLS_CODEPAGE_865 is not set -# CONFIG_NLS_CODEPAGE_866 is not set -# CONFIG_NLS_CODEPAGE_869 is not set -# CONFIG_NLS_CODEPAGE_936 is not set -# CONFIG_NLS_CODEPAGE_950 is not set -# CONFIG_NLS_CODEPAGE_932 is not set -# CONFIG_NLS_CODEPAGE_949 is not set -# CONFIG_NLS_CODEPAGE_874 is not set -# CONFIG_NLS_ISO8859_8 is not set -# CONFIG_NLS_CODEPAGE_1250 is not set -# CONFIG_NLS_CODEPAGE_1251 is not set -# CONFIG_NLS_ASCII is not set -# CONFIG_NLS_ISO8859_1 is not set -# CONFIG_NLS_ISO8859_2 is not set -# CONFIG_NLS_ISO8859_3 is not set -# CONFIG_NLS_ISO8859_4 is not set -# CONFIG_NLS_ISO8859_5 is not set -# CONFIG_NLS_ISO8859_6 is not set -# CONFIG_NLS_ISO8859_7 is not set -# CONFIG_NLS_ISO8859_9 is not set -# CONFIG_NLS_ISO8859_13 is not set -# CONFIG_NLS_ISO8859_14 is not set -# CONFIG_NLS_ISO8859_15 is not set -# CONFIG_NLS_KOI8_R is not set -# CONFIG_NLS_KOI8_U is not set -CONFIG_NLS_UTF8=m -# CONFIG_DLM is not set - -# -# Library routines -# -CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_CRC_CCITT is not set -# CONFIG_CRC16 is not set -CONFIG_CRC_T10DIF=y -CONFIG_CRC_ITU_T=m -CONFIG_CRC32=y -# CONFIG_CRC7 is not set -CONFIG_LIBCRC32C=m -CONFIG_ZLIB_INFLATE=y -CONFIG_PLIST=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HAS_DMA=y -CONFIG_HAVE_LMB=y - -# -# Kernel hacking -# -# CONFIG_PRINTK_TIME is not set -CONFIG_ENABLE_WARN_DEPRECATED=y -CONFIG_ENABLE_MUST_CHECK=y -CONFIG_FRAME_WARN=1024 -# CONFIG_MAGIC_SYSRQ is not set -# CONFIG_UNUSED_SYMBOLS is not set -# CONFIG_DEBUG_FS is not set -# CONFIG_HEADERS_CHECK is not set -CONFIG_DEBUG_KERNEL=y -# CONFIG_DEBUG_SHIRQ is not set -CONFIG_DETECT_SOFTLOCKUP=y -# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set -CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 -CONFIG_SCHED_DEBUG=y -# CONFIG_SCHEDSTATS is not set -# CONFIG_TIMER_STATS is not set -# CONFIG_DEBUG_OBJECTS is not set -# CONFIG_SLUB_DEBUG_ON is not set -# CONFIG_SLUB_STATS is not set -# CONFIG_DEBUG_RT_MUTEXES is not set -# CONFIG_RT_MUTEX_TESTER is not set -# CONFIG_DEBUG_SPINLOCK is not set -# CONFIG_DEBUG_MUTEXES is not set -# CONFIG_DEBUG_SPINLOCK_SLEEP is not set -# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set -# CONFIG_DEBUG_KOBJECT is not set -# CONFIG_DEBUG_HIGHMEM is not set -# CONFIG_DEBUG_BUGVERBOSE is not set -CONFIG_DEBUG_INFO=y -# CONFIG_DEBUG_VM is not set -# CONFIG_DEBUG_WRITECOUNT is not set -# CONFIG_DEBUG_MEMORY_INIT is not set -# CONFIG_DEBUG_LIST is not set -# CONFIG_DEBUG_SG is not set -# CONFIG_BOOT_PRINTK_DELAY is not set -# CONFIG_RCU_TORTURE_TEST is not set -# CONFIG_BACKTRACE_SELF_TEST is not set -# CONFIG_FAULT_INJECTION is not set -# CONFIG_LATENCYTOP is not set -CONFIG_SYSCTL_SYSCALL_CHECK=y -CONFIG_HAVE_FTRACE=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -# CONFIG_FTRACE is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_SAMPLES is not set -CONFIG_HAVE_ARCH_KGDB=y -# CONFIG_KGDB is not set -# CONFIG_DEBUG_STACKOVERFLOW is not set -# CONFIG_DEBUG_STACK_USAGE is not set -# CONFIG_DEBUG_PAGEALLOC is not set -# CONFIG_CODE_PATCHING_SELFTEST is not set -# CONFIG_FTR_FIXUP_SELFTEST is not set -# CONFIG_XMON is not set -# CONFIG_IRQSTACKS is not set -# CONFIG_BDI_SWITCH is not set -# CONFIG_BOOTX_TEXT is not set -# CONFIG_PPC_EARLY_DEBUG is not set - -# -# Security options -# -# CONFIG_KEYS is not set -# CONFIG_SECURITY is not set -# CONFIG_SECURITY_FILE_CAPABILITIES is not set -CONFIG_CRYPTO=y - -# -# Crypto core or helper -# -CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_BLKCIPHER=y -CONFIG_CRYPTO_HASH=y -CONFIG_CRYPTO_MANAGER=y -# CONFIG_CRYPTO_GF128MUL is not set -# CONFIG_CRYPTO_NULL is not set -# CONFIG_CRYPTO_CRYPTD is not set -# CONFIG_CRYPTO_AUTHENC is not set -# CONFIG_CRYPTO_TEST is not set - -# -# Authenticated Encryption with Associated Data -# -# CONFIG_CRYPTO_CCM is not set -# CONFIG_CRYPTO_GCM is not set -# CONFIG_CRYPTO_SEQIV is not set - -# -# Block modes -# -CONFIG_CRYPTO_CBC=y -# CONFIG_CRYPTO_CTR is not set -# CONFIG_CRYPTO_CTS is not set -# CONFIG_CRYPTO_ECB is not set -# CONFIG_CRYPTO_LRW is not set -CONFIG_CRYPTO_PCBC=m -# CONFIG_CRYPTO_XTS is not set - -# -# Hash modes -# -CONFIG_CRYPTO_HMAC=y -# CONFIG_CRYPTO_XCBC is not set - -# -# Digest -# -# CONFIG_CRYPTO_CRC32C is not set -# CONFIG_CRYPTO_MD4 is not set -CONFIG_CRYPTO_MD5=y -# CONFIG_CRYPTO_MICHAEL_MIC is not set -# CONFIG_CRYPTO_RMD128 is not set -# CONFIG_CRYPTO_RMD160 is not set -# CONFIG_CRYPTO_RMD256 is not set -# CONFIG_CRYPTO_RMD320 is not set -CONFIG_CRYPTO_SHA1=m -# CONFIG_CRYPTO_SHA256 is not set -# CONFIG_CRYPTO_SHA512 is not set -# CONFIG_CRYPTO_TGR192 is not set -# CONFIG_CRYPTO_WP512 is not set - -# -# Ciphers -# -# CONFIG_CRYPTO_AES is not set -# CONFIG_CRYPTO_ANUBIS is not set -# CONFIG_CRYPTO_ARC4 is not set -# CONFIG_CRYPTO_BLOWFISH is not set -# CONFIG_CRYPTO_CAMELLIA is not set -# CONFIG_CRYPTO_CAST5 is not set -# CONFIG_CRYPTO_CAST6 is not set -CONFIG_CRYPTO_DES=y -# CONFIG_CRYPTO_FCRYPT is not set -# CONFIG_CRYPTO_KHAZAD is not set -# CONFIG_CRYPTO_SALSA20 is not set -# CONFIG_CRYPTO_SEED is not set -# CONFIG_CRYPTO_SERPENT is not set -# CONFIG_CRYPTO_TEA is not set -# CONFIG_CRYPTO_TWOFISH is not set - -# -# Compression -# -# CONFIG_CRYPTO_DEFLATE is not set -# CONFIG_CRYPTO_LZO is not set -CONFIG_CRYPTO_HW=y -# CONFIG_CRYPTO_DEV_HIFN_795X is not set -# CONFIG_CRYPTO_DEV_TALITOS is not set -# CONFIG_PPC_CLOCK is not set -# CONFIG_VIRTUALIZATION is not set diff --git a/arch/powerpc/configs/mpc86xx_defconfig b/arch/powerpc/configs/mpc86xx_defconfig new file mode 100644 index 00000000000..9d4be820cf1 --- /dev/null +++ b/arch/powerpc/configs/mpc86xx_defconfig @@ -0,0 +1,1646 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.27-rc5 +# Tue Sep 23 23:28:38 2008 +# +# CONFIG_PPC64 is not set + +# +# Processor support +# +CONFIG_6xx=y +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_8xx is not set +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_PPC_FPU=y +CONFIG_ALTIVEC=y +CONFIG_PPC_STD_MMU=y +CONFIG_PPC_STD_MMU_32=y +# CONFIG_PPC_MM_SLICES is not set +CONFIG_SMP=y +CONFIG_NR_CPUS=2 +CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set +CONFIG_IRQ_PER_CPU=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +# CONFIG_ARCH_NO_VIRT_TO_BUS is not set +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_OF=y +CONFIG_PPC_UDBG_16550=y +CONFIG_GENERIC_TBSYNC=y +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +CONFIG_DEFAULT_UIMAGE=y +# CONFIG_PPC_DCR_NATIVE is not set +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +CONFIG_BSD_PROCESS_ACCT=y +# CONFIG_BSD_PROCESS_ACCT_V3 is not set +# CONFIG_TASKSTATS is not set +CONFIG_AUDIT=y +# CONFIG_AUDITSYSCALL is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_GROUP_SCHED=y +# CONFIG_FAIR_GROUP_SCHED is not set +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +CONFIG_KALLSYMS_ALL=y +CONFIG_KALLSYMS_EXTRA_PASS=y +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLUB_DEBUG=y +# CONFIG_SLAB is not set +CONFIG_SLUB=y +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_USE_GENERIC_SMP_HELPERS=y +# CONFIG_HAVE_CLK is not set +CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MODVERSIONS=y +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_STOP_MACHINE=y +CONFIG_BLOCK=y +CONFIG_LBD=y +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +CONFIG_DEFAULT_CFQ=y +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y +# CONFIG_MPC8xxx_GPIO is not set + +# +# Platform support +# +CONFIG_PPC_MULTIPLATFORM=y +CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_MPC5121_ADS is not set +# CONFIG_MPC5121_GENERIC is not set +# CONFIG_PPC_MPC52xx is not set +# CONFIG_PPC_PMAC is not set +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PPC_82xx is not set +# CONFIG_PQ2ADS is not set +# CONFIG_PPC_83xx is not set +CONFIG_PPC_86xx=y +CONFIG_MPC8641_HPCN=y +CONFIG_SBC8641D=y +CONFIG_MPC8610_HPCD=y +CONFIG_GEF_SBC610=y +CONFIG_MPC8641=y +CONFIG_MPC8610=y +# CONFIG_IPIC is not set +CONFIG_MPIC=y +# CONFIG_MPIC_WEIRD is not set +CONFIG_PPC_I8259=y +# CONFIG_PPC_RTAS is not set +# CONFIG_MMIO_NVRAM is not set +# CONFIG_PPC_MPC106 is not set +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +# CONFIG_TAU is not set +CONFIG_FSL_ULI1575=y + +# +# Kernel options +# +CONFIG_HIGHMEM=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_HZ_100 is not set +# CONFIG_HZ_250 is not set +# CONFIG_HZ_300 is not set +CONFIG_HZ_1000=y +CONFIG_HZ=1000 +CONFIG_SCHED_HRTICK=y +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +CONFIG_BINFMT_MISC=m +# CONFIG_IOMMU_HELPER is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_HAS_WALK_MEMORY=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y +# CONFIG_KEXEC is not set +# CONFIG_IRQ_ALL_CPUS is not set +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_FORCE_MAX_ZONEORDER=11 +CONFIG_PROC_DEVICETREE=y +# CONFIG_CMDLINE_BOOL is not set +CONFIG_EXTRA_TARGETS="" +# CONFIG_PM is not set +CONFIG_SECCOMP=y +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +CONFIG_ZONE_DMA=y +CONFIG_GENERIC_ISA_DMA=y +CONFIG_PPC_INDIRECT_PCI=y +CONFIG_FSL_SOC=y +CONFIG_FSL_PCI=y +CONFIG_PPC_PCI_CHOICE=y +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_SYSCALL=y +# CONFIG_PCIEPORTBUS is not set +CONFIG_ARCH_SUPPORTS_MSI=y +# CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y +# CONFIG_PCI_DEBUG is not set +# CONFIG_PCCARD is not set +# CONFIG_HOTPLUG_PCI is not set +CONFIG_HAS_RAPIDIO=y +# CONFIG_RAPIDIO is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_PAGE_OFFSET=0xc0000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_PHYSICAL_START=0x00000000 +CONFIG_TASK_SIZE=0xc0000000 +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=y +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +CONFIG_NET_KEY=m +# CONFIG_NET_KEY_MIGRATE is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_ADVANCED_ROUTER=y +CONFIG_ASK_IP_FIB_HASH=y +# CONFIG_IP_FIB_TRIE is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_MULTIPLE_TABLES=y +CONFIG_IP_ROUTE_MULTIPATH=y +CONFIG_IP_ROUTE_VERBOSE=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +CONFIG_NET_IPIP=y +CONFIG_NET_IPGRE=y +CONFIG_NET_IPGRE_BROADCAST=y +CONFIG_IP_MROUTE=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +CONFIG_ARPD=y +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +CONFIG_INET_TUNNEL=y +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +CONFIG_IPV6=y +# CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +# CONFIG_INET6_AH is not set +# CONFIG_INET6_ESP is not set +# CONFIG_INET6_IPCOMP is not set +# CONFIG_IPV6_MIP6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +CONFIG_INET6_XFRM_MODE_TRANSPORT=y +CONFIG_INET6_XFRM_MODE_TUNNEL=y +CONFIG_INET6_XFRM_MODE_BEET=y +# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set +CONFIG_IPV6_SIT=y +CONFIG_IPV6_NDISC_NODETYPE=y +# CONFIG_IPV6_TUNNEL is not set +# CONFIG_IPV6_MULTIPLE_TABLES is not set +# CONFIG_IPV6_MROUTE is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +CONFIG_IP_SCTP=m +# CONFIG_SCTP_DBG_MSG is not set +# CONFIG_SCTP_DBG_OBJCNT is not set +# CONFIG_SCTP_HMAC_NONE is not set +# CONFIG_SCTP_HMAC_SHA1 is not set +CONFIG_SCTP_HMAC_MD5=y +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +CONFIG_FIB_RULES=y + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +# CONFIG_MTD is not set +CONFIG_OF_DEVICE=y +CONFIG_OF_I2C=y +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +CONFIG_BLK_DEV_NBD=y +# CONFIG_BLK_DEV_SX8 is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=131072 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set +CONFIG_MISC_DEVICES=y +# CONFIG_PHANTOM is not set +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_SGI_IOC4 is not set +# CONFIG_TIFM_CORE is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_HP_ILO is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +CONFIG_CHR_DEV_ST=y +# CONFIG_CHR_DEV_OSST is not set +CONFIG_BLK_DEV_SR=y +# CONFIG_BLK_DEV_SR_VENDOR is not set +CONFIG_CHR_DEV_SG=y +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +# CONFIG_SCSI_CONSTANTS is not set +CONFIG_SCSI_LOGGING=y +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set +# CONFIG_SCSI_ACARD is not set +# CONFIG_SCSI_AACRAID is not set +# CONFIG_SCSI_AIC7XXX is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_AIC79XX is not set +# CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set +# CONFIG_SCSI_ARCMSR is not set +# CONFIG_MEGARAID_NEWGEN is not set +# CONFIG_MEGARAID_LEGACY is not set +# CONFIG_MEGARAID_SAS is not set +# CONFIG_SCSI_HPTIOP is not set +# CONFIG_SCSI_BUSLOGIC is not set +# CONFIG_SCSI_DMX3191D is not set +# CONFIG_SCSI_EATA is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GDTH is not set +# CONFIG_SCSI_IPS is not set +# CONFIG_SCSI_INITIO is not set +# CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_MVSAS is not set +# CONFIG_SCSI_STEX is not set +# CONFIG_SCSI_SYM53C8XX_2 is not set +# CONFIG_SCSI_IPR is not set +# CONFIG_SCSI_QLOGIC_1280 is not set +# CONFIG_SCSI_QLA_FC is not set +# CONFIG_SCSI_QLA_ISCSI is not set +# CONFIG_SCSI_LPFC is not set +# CONFIG_SCSI_DC395x is not set +# CONFIG_SCSI_DC390T is not set +# CONFIG_SCSI_NSP32 is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_DH is not set +CONFIG_ATA=y +# CONFIG_ATA_NONSTANDARD is not set +CONFIG_SATA_PMP=y +CONFIG_SATA_AHCI=y +# CONFIG_SATA_SIL24 is not set +# CONFIG_SATA_FSL is not set +CONFIG_ATA_SFF=y +# CONFIG_SATA_SVW is not set +# CONFIG_ATA_PIIX is not set +# CONFIG_SATA_MV is not set +# CONFIG_SATA_NV is not set +# CONFIG_PDC_ADMA is not set +# CONFIG_SATA_QSTOR is not set +# CONFIG_SATA_PROMISE is not set +# CONFIG_SATA_SX4 is not set +# CONFIG_SATA_SIL is not set +# CONFIG_SATA_SIS is not set +# CONFIG_SATA_ULI is not set +# CONFIG_SATA_VIA is not set +# CONFIG_SATA_VITESSE is not set +# CONFIG_SATA_INIC162X is not set +CONFIG_PATA_ALI=y +# CONFIG_PATA_AMD is not set +# CONFIG_PATA_ARTOP is not set +# CONFIG_PATA_ATIIXP is not set +# CONFIG_PATA_CMD640_PCI is not set +# CONFIG_PATA_CMD64X is not set +# CONFIG_PATA_CS5520 is not set +# CONFIG_PATA_CS5530 is not set +# CONFIG_PATA_CYPRESS is not set +# CONFIG_PATA_EFAR is not set +# CONFIG_ATA_GENERIC is not set +# CONFIG_PATA_HPT366 is not set +# CONFIG_PATA_HPT37X is not set +# CONFIG_PATA_HPT3X2N is not set +# CONFIG_PATA_HPT3X3 is not set +# CONFIG_PATA_IT821X is not set +# CONFIG_PATA_IT8213 is not set +# CONFIG_PATA_JMICRON is not set +# CONFIG_PATA_TRIFLEX is not set +# CONFIG_PATA_MARVELL is not set +# CONFIG_PATA_MPIIX is not set +# CONFIG_PATA_OLDPIIX is not set +# CONFIG_PATA_NETCELL is not set +# CONFIG_PATA_NINJA32 is not set +# CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set +# CONFIG_PATA_OPTI is not set +# CONFIG_PATA_OPTIDMA is not set +# CONFIG_PATA_PDC_OLD is not set +# CONFIG_PATA_RADISYS is not set +# CONFIG_PATA_RZ1000 is not set +# CONFIG_PATA_SC1200 is not set +# CONFIG_PATA_SERVERWORKS is not set +# CONFIG_PATA_PDC2027X is not set +# CONFIG_PATA_SIL680 is not set +# CONFIG_PATA_SIS is not set +# CONFIG_PATA_VIA is not set +# CONFIG_PATA_WINBOND is not set +# CONFIG_PATA_PLATFORM is not set +# CONFIG_PATA_SCH is not set +# CONFIG_MD is not set +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# Enable only one of the two stacks, unless you know what you are doing +# +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set +# CONFIG_I2O is not set +# CONFIG_MACINTOSH_DRIVERS is not set +CONFIG_NETDEVICES=y +CONFIG_DUMMY=y +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +CONFIG_VITESSE_PHY=y +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_NET_PCI is not set +# CONFIG_B44 is not set +CONFIG_NETDEV_1000=y +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_E1000E is not set +# CONFIG_IP1000 is not set +# CONFIG_IGB is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_VIA_VELOCITY is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set +CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set +# CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set +# CONFIG_ATL1E is not set +CONFIG_NETDEV_10000=y +# CONFIG_CHELSIO_T1 is not set +# CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set +# CONFIG_IXGB is not set +# CONFIG_S2IO is not set +# CONFIG_MYRI10GE is not set +# CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set +# CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set +# CONFIG_BNX2X is not set +# CONFIG_SFC is not set +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NET_FC is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_I8042=y +CONFIG_SERIO_SERPORT=y +# CONFIG_SERIO_PCIPS2 is not set +CONFIG_SERIO_LIBPS2=y +# CONFIG_SERIO_RAW is not set +# CONFIG_SERIO_XILINX_XPS_PS2 is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y +CONFIG_SERIAL_8250_NR_UARTS=2 +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_MANY_PORTS=y +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_8250_DETECT_IRQ=y +CONFIG_SERIAL_8250_RSA=y + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set +# CONFIG_SERIAL_OF_PLATFORM is not set +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +CONFIG_NVRAM=y +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +# CONFIG_I2C_CHARDEV is not set +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# PC SMBus host controller drivers +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI1563 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_ISCH is not set +# CONFIG_I2C_PIIX4 is not set +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_VIA is not set +# CONFIG_I2C_VIAPRO is not set + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_MPC=y +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Graphics adapter I2C/DDC channel drivers +# +# CONFIG_I2C_VOODOO3 is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_AT24 is not set +CONFIG_SENSORS_EEPROM=y +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +# CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +CONFIG_DVB_CORE=m +CONFIG_VIDEO_MEDIA=m + +# +# Multimedia drivers +# +# CONFIG_MEDIA_ATTACH is not set +CONFIG_MEDIA_TUNER=m +# CONFIG_MEDIA_TUNER_CUSTOMIZE is not set +CONFIG_MEDIA_TUNER_SIMPLE=m +CONFIG_MEDIA_TUNER_TDA8290=m +CONFIG_MEDIA_TUNER_TDA9887=m +CONFIG_MEDIA_TUNER_TEA5761=m +CONFIG_MEDIA_TUNER_TEA5767=m +CONFIG_MEDIA_TUNER_MT20XX=m +CONFIG_MEDIA_TUNER_XC2028=m +CONFIG_MEDIA_TUNER_XC5000=m +CONFIG_DVB_CAPTURE_DRIVERS=y + +# +# Supported SAA7146 based PCI Adapters +# +# CONFIG_TTPCI_EEPROM is not set +# CONFIG_DVB_BUDGET_CORE is not set + +# +# Supported USB Adapters +# +# CONFIG_DVB_USB is not set +# CONFIG_DVB_TTUSB_BUDGET is not set +# CONFIG_DVB_TTUSB_DEC is not set +# CONFIG_DVB_CINERGYT2 is not set +# CONFIG_DVB_SIANO_SMS1XXX is not set + +# +# Supported FlexCopII (B2C2) Adapters +# +# CONFIG_DVB_B2C2_FLEXCOP is not set + +# +# Supported BT878 Adapters +# + +# +# Supported Pluto2 Adapters +# +# CONFIG_DVB_PLUTO2 is not set + +# +# Supported DVB Frontends +# + +# +# Customise DVB Frontends +# +# CONFIG_DVB_FE_CUSTOMISE is not set + +# +# DVB-S (satellite) frontends +# +# CONFIG_DVB_CX24110 is not set +# CONFIG_DVB_CX24123 is not set +# CONFIG_DVB_MT312 is not set +# CONFIG_DVB_S5H1420 is not set +# CONFIG_DVB_STV0299 is not set +# CONFIG_DVB_TDA8083 is not set +# CONFIG_DVB_TDA10086 is not set +# CONFIG_DVB_VES1X93 is not set +# CONFIG_DVB_TUNER_ITD1000 is not set +# CONFIG_DVB_TDA826X is not set +# CONFIG_DVB_TUA6100 is not set + +# +# DVB-T (terrestrial) frontends +# +# CONFIG_DVB_SP8870 is not set +# CONFIG_DVB_SP887X is not set +# CONFIG_DVB_CX22700 is not set +# CONFIG_DVB_CX22702 is not set +# CONFIG_DVB_DRX397XD is not set +# CONFIG_DVB_L64781 is not set +# CONFIG_DVB_TDA1004X is not set +# CONFIG_DVB_NXT6000 is not set +# CONFIG_DVB_MT352 is not set +# CONFIG_DVB_ZL10353 is not set +# CONFIG_DVB_DIB3000MB is not set +# CONFIG_DVB_DIB3000MC is not set +# CONFIG_DVB_DIB7000M is not set +# CONFIG_DVB_DIB7000P is not set +# CONFIG_DVB_TDA10048 is not set + +# +# DVB-C (cable) frontends +# +# CONFIG_DVB_VES1820 is not set +# CONFIG_DVB_TDA10021 is not set +# CONFIG_DVB_TDA10023 is not set +# CONFIG_DVB_STV0297 is not set + +# +# ATSC (North American/Korean Terrestrial/Cable DTV) frontends +# +# CONFIG_DVB_NXT200X is not set +# CONFIG_DVB_OR51211 is not set +# CONFIG_DVB_OR51132 is not set +# CONFIG_DVB_BCM3510 is not set +# CONFIG_DVB_LGDT330X is not set +# CONFIG_DVB_S5H1409 is not set +# CONFIG_DVB_AU8522 is not set +# CONFIG_DVB_S5H1411 is not set + +# +# Digital terrestrial only tuners/PLL +# +# CONFIG_DVB_PLL is not set +# CONFIG_DVB_TUNER_DIB0070 is not set + +# +# SEC control devices for DVB-S +# +# CONFIG_DVB_LNBP21 is not set +# CONFIG_DVB_ISL6405 is not set +# CONFIG_DVB_ISL6421 is not set +CONFIG_DAB=y +# CONFIG_USB_DABUSB is not set + +# +# Graphics support +# +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +CONFIG_VGA_CONSOLE=y +# CONFIG_VGACON_SOFT_SCROLLBACK is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_SOUND=y +CONFIG_SND=y +CONFIG_SND_TIMER=y +CONFIG_SND_PCM=y +# CONFIG_SND_SEQUENCER is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=y +CONFIG_SND_PCM_OSS=y +CONFIG_SND_PCM_OSS_PLUGINS=y +# CONFIG_SND_DYNAMIC_MINORS is not set +# CONFIG_SND_SUPPORT_OLD_API is not set +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +CONFIG_SND_VMASTER=y +CONFIG_SND_AC97_CODEC=y +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +# CONFIG_SND_AC97_POWER_SAVE is not set +CONFIG_SND_PCI=y +# CONFIG_SND_AD1889 is not set +# CONFIG_SND_ALS300 is not set +# CONFIG_SND_ALS4000 is not set +# CONFIG_SND_ALI5451 is not set +# CONFIG_SND_ATIIXP is not set +# CONFIG_SND_ATIIXP_MODEM is not set +# CONFIG_SND_AU8810 is not set +# CONFIG_SND_AU8820 is not set +# CONFIG_SND_AU8830 is not set +# CONFIG_SND_AW2 is not set +# CONFIG_SND_AZT3328 is not set +# CONFIG_SND_BT87X is not set +# CONFIG_SND_CA0106 is not set +# CONFIG_SND_CMIPCI is not set +# CONFIG_SND_OXYGEN is not set +# CONFIG_SND_CS4281 is not set +# CONFIG_SND_CS46XX is not set +# CONFIG_SND_CS5530 is not set +# CONFIG_SND_DARLA20 is not set +# CONFIG_SND_GINA20 is not set +# CONFIG_SND_LAYLA20 is not set +# CONFIG_SND_DARLA24 is not set +# CONFIG_SND_GINA24 is not set +# CONFIG_SND_LAYLA24 is not set +# CONFIG_SND_MONA is not set +# CONFIG_SND_MIA is not set +# CONFIG_SND_ECHO3G is not set +# CONFIG_SND_INDIGO is not set +# CONFIG_SND_INDIGOIO is not set +# CONFIG_SND_INDIGODJ is not set +# CONFIG_SND_EMU10K1 is not set +# CONFIG_SND_EMU10K1X is not set +# CONFIG_SND_ENS1370 is not set +# CONFIG_SND_ENS1371 is not set +# CONFIG_SND_ES1938 is not set +# CONFIG_SND_ES1968 is not set +# CONFIG_SND_FM801 is not set +# CONFIG_SND_HDA_INTEL is not set +# CONFIG_SND_HDSP is not set +# CONFIG_SND_HDSPM is not set +# CONFIG_SND_HIFIER is not set +# CONFIG_SND_ICE1712 is not set +# CONFIG_SND_ICE1724 is not set +CONFIG_SND_INTEL8X0=y +# CONFIG_SND_INTEL8X0M is not set +# CONFIG_SND_KORG1212 is not set +# CONFIG_SND_MAESTRO3 is not set +# CONFIG_SND_MIXART is not set +# CONFIG_SND_NM256 is not set +# CONFIG_SND_PCXHR is not set +# CONFIG_SND_RIPTIDE is not set +# CONFIG_SND_RME32 is not set +# CONFIG_SND_RME96 is not set +# CONFIG_SND_RME9652 is not set +# CONFIG_SND_SONICVIBES is not set +# CONFIG_SND_TRIDENT is not set +# CONFIG_SND_VIA82XX is not set +# CONFIG_SND_VIA82XX_MODEM is not set +# CONFIG_SND_VIRTUOSO is not set +# CONFIG_SND_VX222 is not set +# CONFIG_SND_YMFPCI is not set +CONFIG_SND_PPC=y +CONFIG_SND_USB=y +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_USX2Y is not set +# CONFIG_SND_USB_CAIAQ is not set +# CONFIG_SND_SOC is not set +# CONFIG_SOUND_PRIME is not set +CONFIG_AC97_BUS=y +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_USB_HIDINPUT_POWERBOOK is not set +# CONFIG_HID_FF is not set +# CONFIG_USB_HIDDEV is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=y + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +CONFIG_USB_EHCI_HCD=y +# CONFIG_USB_EHCI_ROOT_HUB_TT is not set +# CONFIG_USB_EHCI_TT_NEWSCHED is not set +# CONFIG_USB_EHCI_FSL is not set +CONFIG_USB_EHCI_HCD_PPC_OF=y +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_HCD_PPC_OF=y +CONFIG_USB_OHCI_HCD_PPC_OF_BE=y +CONFIG_USB_OHCI_HCD_PPC_OF_LE=y +CONFIG_USB_OHCI_HCD_PCI=y +CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y +CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_SIERRA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +# CONFIG_INFINIBAND is not set +# CONFIG_EDAC is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set + +# +# SPI RTC drivers +# + +# +# Platform RTC drivers +# +CONFIG_RTC_DRV_CMOS=y +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_RTC_DRV_PPC is not set +# CONFIG_DMADEVICES is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +CONFIG_ISO9660_FS=m +CONFIG_JOLIET=y +CONFIG_ZISOFS=y +CONFIG_UDF_FS=m +CONFIG_UDF_NLS=y + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=m +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +CONFIG_NTFS_FS=y +# CONFIG_NTFS_DEBUG is not set +# CONFIG_NTFS_RW is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +CONFIG_ADFS_FS=m +# CONFIG_ADFS_FS_RW is not set +CONFIG_AFFS_FS=m +CONFIG_HFS_FS=m +CONFIG_HFSPLUS_FS=m +CONFIG_BEFS_FS=m +# CONFIG_BEFS_DEBUG is not set +CONFIG_BFS_FS=m +CONFIG_EFS_FS=m +CONFIG_CRAMFS=y +CONFIG_VXFS_FS=m +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +CONFIG_HPFS_FS=m +CONFIG_QNX4FS_FS=m +# CONFIG_ROMFS_FS is not set +CONFIG_SYSV_FS=m +CONFIG_UFS_FS=m +# CONFIG_UFS_FS_WRITE is not set +# CONFIG_UFS_DEBUG is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +CONFIG_NFS_V4=y +CONFIG_ROOT_NFS=y +CONFIG_NFSD=y +# CONFIG_NFSD_V3 is not set +# CONFIG_NFSD_V4 is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_EXPORTFS=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +CONFIG_MAC_PARTITION=y +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y +CONFIG_CRC_ITU_T=m +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=m +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_HAVE_LMB=y + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_SLUB_STATS is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_HIGHMEM is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_HAVE_FTRACE=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +# CONFIG_FTRACE is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_MSI_BITMAP_SELFTEST is not set +# CONFIG_XMON is not set +# CONFIG_IRQSTACKS is not set +# CONFIG_BDI_SWITCH is not set +# CONFIG_BOOTX_TEXT is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +CONFIG_CRYPTO_HMAC=y +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +CONFIG_CRYPTO_SHA1=m +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y +# CONFIG_CRYPTO_DEV_HIFN_795X is not set +# CONFIG_CRYPTO_DEV_TALITOS is not set +# CONFIG_PPC_CLOCK is not set +# CONFIG_VIRTUALIZATION is not set diff --git a/arch/powerpc/configs/sbc8641d_defconfig b/arch/powerpc/configs/sbc8641d_defconfig deleted file mode 100644 index f545421f985..00000000000 --- a/arch/powerpc/configs/sbc8641d_defconfig +++ /dev/null @@ -1,1481 +0,0 @@ -# -# Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc4 -# Thu Aug 21 00:52:15 2008 -# -# CONFIG_PPC64 is not set - -# -# Processor support -# -CONFIG_6xx=y -# CONFIG_PPC_85xx is not set -# CONFIG_PPC_8xx is not set -# CONFIG_40x is not set -# CONFIG_44x is not set -# CONFIG_E200 is not set -CONFIG_PPC_FPU=y -CONFIG_ALTIVEC=y -CONFIG_PPC_STD_MMU=y -CONFIG_PPC_STD_MMU_32=y -# CONFIG_PPC_MM_SLICES is not set -CONFIG_SMP=y -CONFIG_NR_CPUS=2 -CONFIG_PPC32=y -CONFIG_WORD_SIZE=32 -CONFIG_PPC_MERGE=y -CONFIG_MMU=y -CONFIG_GENERIC_CMOS_UPDATE=y -CONFIG_GENERIC_TIME=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_HARDIRQS=y -# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set -CONFIG_IRQ_PER_CPU=y -CONFIG_STACKTRACE_SUPPORT=y -CONFIG_HAVE_LATENCYTOP_SUPPORT=y -CONFIG_LOCKDEP_SUPPORT=y -CONFIG_RWSEM_XCHGADD_ALGORITHM=y -CONFIG_GENERIC_LOCKBREAK=y -CONFIG_ARCH_HAS_ILOG2_U32=y -CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_GENERIC_FIND_NEXT_BIT=y -# CONFIG_ARCH_NO_VIRT_TO_BUS is not set -CONFIG_PPC=y -CONFIG_EARLY_PRINTK=y -CONFIG_GENERIC_NVRAM=y -CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y -CONFIG_ARCH_MAY_HAVE_PC_FDC=y -CONFIG_PPC_OF=y -CONFIG_OF=y -CONFIG_PPC_UDBG_16550=y -CONFIG_GENERIC_TBSYNC=y -CONFIG_AUDIT_ARCH=y -CONFIG_GENERIC_BUG=y -CONFIG_DEFAULT_UIMAGE=y -# CONFIG_PPC_DCR_NATIVE is not set -# CONFIG_PPC_DCR_MMIO is not set -CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" - -# -# General setup -# -CONFIG_EXPERIMENTAL=y -CONFIG_LOCK_KERNEL=y -CONFIG_INIT_ENV_ARG_LIMIT=32 -CONFIG_LOCALVERSION="" -CONFIG_LOCALVERSION_AUTO=y -CONFIG_SWAP=y -CONFIG_SYSVIPC=y -CONFIG_SYSVIPC_SYSCTL=y -CONFIG_POSIX_MQUEUE=y -CONFIG_BSD_PROCESS_ACCT=y -CONFIG_BSD_PROCESS_ACCT_V3=y -# CONFIG_TASKSTATS is not set -# CONFIG_AUDIT is not set -CONFIG_IKCONFIG=y -CONFIG_IKCONFIG_PROC=y -CONFIG_LOG_BUF_SHIFT=14 -# CONFIG_CGROUPS is not set -CONFIG_GROUP_SCHED=y -CONFIG_FAIR_GROUP_SCHED=y -# CONFIG_RT_GROUP_SCHED is not set -CONFIG_USER_SCHED=y -# CONFIG_CGROUP_SCHED is not set -CONFIG_SYSFS_DEPRECATED=y -CONFIG_SYSFS_DEPRECATED_V2=y -CONFIG_RELAY=y -# CONFIG_NAMESPACES is not set -CONFIG_BLK_DEV_INITRD=y -CONFIG_INITRAMFS_SOURCE="" -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set -CONFIG_SYSCTL=y -CONFIG_EMBEDDED=y -CONFIG_SYSCTL_SYSCALL=y -CONFIG_KALLSYMS=y -# CONFIG_KALLSYMS_ALL is not set -# CONFIG_KALLSYMS_EXTRA_PASS is not set -CONFIG_HOTPLUG=y -CONFIG_PRINTK=y -CONFIG_BUG=y -CONFIG_ELF_CORE=y -CONFIG_PCSPKR_PLATFORM=y -CONFIG_COMPAT_BRK=y -CONFIG_BASE_FULL=y -CONFIG_FUTEX=y -CONFIG_ANON_INODES=y -CONFIG_EPOLL=y -CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y -CONFIG_EVENTFD=y -CONFIG_SHMEM=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_SLAB=y -# CONFIG_SLUB is not set -# CONFIG_SLOB is not set -# CONFIG_PROFILING is not set -# CONFIG_MARKERS is not set -CONFIG_HAVE_OPROFILE=y -# CONFIG_KPROBES is not set -CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y -CONFIG_HAVE_IOREMAP_PROT=y -CONFIG_HAVE_KPROBES=y -CONFIG_HAVE_KRETPROBES=y -CONFIG_HAVE_ARCH_TRACEHOOK=y -# CONFIG_HAVE_DMA_ATTRS is not set -CONFIG_USE_GENERIC_SMP_HELPERS=y -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y -# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set -CONFIG_SLABINFO=y -CONFIG_RT_MUTEXES=y -# CONFIG_TINY_SHMEM is not set -CONFIG_BASE_SMALL=0 -CONFIG_MODULES=y -# CONFIG_MODULE_FORCE_LOAD is not set -CONFIG_MODULE_UNLOAD=y -# CONFIG_MODULE_FORCE_UNLOAD is not set -# CONFIG_MODVERSIONS is not set -# CONFIG_MODULE_SRCVERSION_ALL is not set -CONFIG_KMOD=y -CONFIG_STOP_MACHINE=y -CONFIG_BLOCK=y -# CONFIG_LBD is not set -# CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_LSF is not set -# CONFIG_BLK_DEV_BSG is not set -# CONFIG_BLK_DEV_INTEGRITY is not set - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y -# CONFIG_DEFAULT_AS is not set -# CONFIG_DEFAULT_DEADLINE is not set -CONFIG_DEFAULT_CFQ=y -# CONFIG_DEFAULT_NOOP is not set -CONFIG_DEFAULT_IOSCHED="cfq" -CONFIG_CLASSIC_RCU=y - -# -# Platform support -# -CONFIG_PPC_MULTIPLATFORM=y -CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y -# CONFIG_MPC5121_ADS is not set -# CONFIG_MPC5121_GENERIC is not set -# CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y -# CONFIG_PPC_CELL is not set -# CONFIG_PPC_CELL_NATIVE is not set -# CONFIG_PPC_82xx is not set -# CONFIG_PQ2ADS is not set -# CONFIG_PPC_83xx is not set -CONFIG_PPC_86xx=y -# CONFIG_MPC8641_HPCN is not set -CONFIG_SBC8641D=y -# CONFIG_MPC8610_HPCD is not set -CONFIG_MPC8641=y -CONFIG_PPC_NATIVE=y -# CONFIG_UDBG_RTAS_CONSOLE is not set -# CONFIG_IPIC is not set -CONFIG_MPIC=y -# CONFIG_MPIC_WEIRD is not set -CONFIG_PPC_I8259=y -CONFIG_PPC_RTAS=y -# CONFIG_RTAS_ERROR_LOGGING is not set -CONFIG_RTAS_PROC=y -# CONFIG_MMIO_NVRAM is not set -CONFIG_PPC_MPC106=y -# CONFIG_PPC_970_NAP is not set -# CONFIG_PPC_INDIRECT_IO is not set -# CONFIG_GENERIC_IOMAP is not set -# CONFIG_CPU_FREQ is not set -# CONFIG_PPC601_SYNC_FIX is not set -# CONFIG_TAU is not set -# CONFIG_FSL_ULI1575 is not set - -# -# Kernel options -# -# CONFIG_HIGHMEM is not set -CONFIG_TICK_ONESHOT=y -# CONFIG_NO_HZ is not set -CONFIG_HIGH_RES_TIMERS=y -CONFIG_GENERIC_CLOCKEVENTS_BUILD=y -# CONFIG_HZ_100 is not set -CONFIG_HZ_250=y -# CONFIG_HZ_300 is not set -# CONFIG_HZ_1000 is not set -CONFIG_HZ=250 -CONFIG_SCHED_HRTICK=y -# CONFIG_PREEMPT_NONE is not set -# CONFIG_PREEMPT_VOLUNTARY is not set -CONFIG_PREEMPT=y -# CONFIG_PREEMPT_RCU is not set -CONFIG_BINFMT_ELF=y -CONFIG_BINFMT_MISC=m -# CONFIG_IOMMU_HELPER is not set -# CONFIG_HOTPLUG_CPU is not set -CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y -CONFIG_ARCH_HAS_WALK_MEMORY=y -CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y -# CONFIG_KEXEC is not set -CONFIG_IRQ_ALL_CPUS=y -CONFIG_ARCH_FLATMEM_ENABLE=y -CONFIG_ARCH_POPULATES_NODE_MAP=y -CONFIG_SELECT_MEMORY_MODEL=y -CONFIG_FLATMEM_MANUAL=y -# CONFIG_DISCONTIGMEM_MANUAL is not set -# CONFIG_SPARSEMEM_MANUAL is not set -CONFIG_FLATMEM=y -CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set -CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_SPLIT_PTLOCK_CPUS=4 -CONFIG_MIGRATION=y -# CONFIG_RESOURCES_64BIT is not set -CONFIG_ZONE_DMA_FLAG=1 -CONFIG_BOUNCE=y -CONFIG_VIRT_TO_BUS=y -CONFIG_FORCE_MAX_ZONEORDER=11 -# CONFIG_PROC_DEVICETREE is not set -# CONFIG_CMDLINE_BOOL is not set -CONFIG_EXTRA_TARGETS="" -# CONFIG_PM is not set -CONFIG_SECCOMP=y -CONFIG_ISA_DMA_API=y - -# -# Bus options -# -# CONFIG_ISA is not set -CONFIG_ZONE_DMA=y -CONFIG_GENERIC_ISA_DMA=y -CONFIG_PPC_INDIRECT_PCI=y -CONFIG_FSL_SOC=y -CONFIG_FSL_PCI=y -CONFIG_PPC_PCI_CHOICE=y -CONFIG_PCI=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_SYSCALL=y -CONFIG_PCIEPORTBUS=y -CONFIG_PCIEAER=y -# CONFIG_PCIEASPM is not set -CONFIG_ARCH_SUPPORTS_MSI=y -# CONFIG_PCI_MSI is not set -CONFIG_PCI_LEGACY=y -# CONFIG_PCI_DEBUG is not set -# CONFIG_PCCARD is not set -# CONFIG_HOTPLUG_PCI is not set -# CONFIG_HAS_RAPIDIO is not set - -# -# Advanced setup -# -# CONFIG_ADVANCED_OPTIONS is not set - -# -# Default settings for advanced configuration options are used -# -CONFIG_LOWMEM_SIZE=0x30000000 -CONFIG_PAGE_OFFSET=0xc0000000 -CONFIG_KERNEL_START=0xc0000000 -CONFIG_PHYSICAL_START=0x00000000 -CONFIG_TASK_SIZE=0xc0000000 -CONFIG_NET=y - -# -# Networking options -# -CONFIG_PACKET=y -CONFIG_PACKET_MMAP=y -CONFIG_UNIX=y -CONFIG_XFRM=y -CONFIG_XFRM_USER=m -# CONFIG_XFRM_SUB_POLICY is not set -# CONFIG_XFRM_MIGRATE is not set -# CONFIG_XFRM_STATISTICS is not set -CONFIG_XFRM_IPCOMP=m -CONFIG_NET_KEY=m -# CONFIG_NET_KEY_MIGRATE is not set -CONFIG_INET=y -CONFIG_IP_MULTICAST=y -CONFIG_IP_ADVANCED_ROUTER=y -CONFIG_ASK_IP_FIB_HASH=y -# CONFIG_IP_FIB_TRIE is not set -CONFIG_IP_FIB_HASH=y -CONFIG_IP_MULTIPLE_TABLES=y -CONFIG_IP_ROUTE_MULTIPATH=y -CONFIG_IP_ROUTE_VERBOSE=y -CONFIG_IP_PNP=y -CONFIG_IP_PNP_DHCP=y -CONFIG_IP_PNP_BOOTP=y -CONFIG_IP_PNP_RARP=y -CONFIG_NET_IPIP=m -CONFIG_NET_IPGRE=m -CONFIG_NET_IPGRE_BROADCAST=y -CONFIG_IP_MROUTE=y -CONFIG_IP_PIMSM_V1=y -CONFIG_IP_PIMSM_V2=y -# CONFIG_ARPD is not set -CONFIG_SYN_COOKIES=y -CONFIG_INET_AH=m -CONFIG_INET_ESP=m -CONFIG_INET_IPCOMP=m -CONFIG_INET_XFRM_TUNNEL=m -CONFIG_INET_TUNNEL=m -CONFIG_INET_XFRM_MODE_TRANSPORT=y -CONFIG_INET_XFRM_MODE_TUNNEL=y -CONFIG_INET_XFRM_MODE_BEET=y -# CONFIG_INET_LRO is not set -CONFIG_INET_DIAG=y -CONFIG_INET_TCP_DIAG=y -# CONFIG_TCP_CONG_ADVANCED is not set -CONFIG_TCP_CONG_CUBIC=y -CONFIG_DEFAULT_TCP_CONG="cubic" -# CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set -CONFIG_IPV6=m -# CONFIG_IPV6_PRIVACY is not set -# CONFIG_IPV6_ROUTER_PREF is not set -# CONFIG_IPV6_OPTIMISTIC_DAD is not set -CONFIG_INET6_AH=m -CONFIG_INET6_ESP=m -CONFIG_INET6_IPCOMP=m -# CONFIG_IPV6_MIP6 is not set -CONFIG_INET6_XFRM_TUNNEL=m -CONFIG_INET6_TUNNEL=m -CONFIG_INET6_XFRM_MODE_TRANSPORT=m -CONFIG_INET6_XFRM_MODE_TUNNEL=m -CONFIG_INET6_XFRM_MODE_BEET=m -# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set -CONFIG_IPV6_SIT=m -CONFIG_IPV6_NDISC_NODETYPE=y -CONFIG_IPV6_TUNNEL=m -# CONFIG_IPV6_MULTIPLE_TABLES is not set -# CONFIG_IPV6_MROUTE is not set -# CONFIG_NETLABEL is not set -# CONFIG_NETWORK_SECMARK is not set -CONFIG_NETFILTER=y -# CONFIG_NETFILTER_DEBUG is not set -CONFIG_NETFILTER_ADVANCED=y -CONFIG_BRIDGE_NETFILTER=y - -# -# Core Netfilter Configuration -# -# CONFIG_NETFILTER_NETLINK_QUEUE is not set -# CONFIG_NETFILTER_NETLINK_LOG is not set -# CONFIG_NF_CONNTRACK is not set -CONFIG_NETFILTER_XTABLES=m -# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set -# CONFIG_NETFILTER_XT_TARGET_DSCP is not set -# CONFIG_NETFILTER_XT_TARGET_MARK is not set -# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set -# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set -# CONFIG_NETFILTER_XT_TARGET_RATEEST is not set -# CONFIG_NETFILTER_XT_TARGET_TRACE is not set -# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set -# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set -# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set -# CONFIG_NETFILTER_XT_MATCH_DCCP is not set -# CONFIG_NETFILTER_XT_MATCH_DSCP is not set -# CONFIG_NETFILTER_XT_MATCH_ESP is not set -# CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set -# CONFIG_NETFILTER_XT_MATCH_LENGTH is not set -# CONFIG_NETFILTER_XT_MATCH_LIMIT is not set -# CONFIG_NETFILTER_XT_MATCH_MAC is not set -# CONFIG_NETFILTER_XT_MATCH_MARK is not set -# CONFIG_NETFILTER_XT_MATCH_OWNER is not set -# CONFIG_NETFILTER_XT_MATCH_POLICY is not set -# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set -# CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set -# CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set -# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set -# CONFIG_NETFILTER_XT_MATCH_RATEEST is not set -# CONFIG_NETFILTER_XT_MATCH_REALM is not set -# CONFIG_NETFILTER_XT_MATCH_SCTP is not set -# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set -# CONFIG_NETFILTER_XT_MATCH_STRING is not set -# CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set -# CONFIG_NETFILTER_XT_MATCH_TIME is not set -# CONFIG_NETFILTER_XT_MATCH_U32 is not set -# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set - -# -# IP: Netfilter Configuration -# -CONFIG_IP_NF_QUEUE=m -CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m -# CONFIG_IP_NF_MATCH_AH is not set -CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m -CONFIG_IP_NF_FILTER=m -CONFIG_IP_NF_TARGET_REJECT=m -CONFIG_IP_NF_TARGET_LOG=m -CONFIG_IP_NF_TARGET_ULOG=m -CONFIG_IP_NF_MANGLE=m -CONFIG_IP_NF_TARGET_ECN=m -# CONFIG_IP_NF_TARGET_TTL is not set -CONFIG_IP_NF_RAW=m -# CONFIG_IP_NF_SECURITY is not set -CONFIG_IP_NF_ARPTABLES=m -CONFIG_IP_NF_ARPFILTER=m -CONFIG_IP_NF_ARP_MANGLE=m - -# -# IPv6: Netfilter Configuration -# -CONFIG_IP6_NF_QUEUE=m -CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m -CONFIG_IP6_NF_MATCH_FRAG=m -CONFIG_IP6_NF_MATCH_HL=m -CONFIG_IP6_NF_MATCH_IPV6HEADER=m -# CONFIG_IP6_NF_MATCH_AH is not set -# CONFIG_IP6_NF_MATCH_MH is not set -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m -CONFIG_IP6_NF_TARGET_LOG=m -# CONFIG_IP6_NF_TARGET_REJECT is not set -CONFIG_IP6_NF_MANGLE=m -# CONFIG_IP6_NF_TARGET_HL is not set -CONFIG_IP6_NF_RAW=m -# CONFIG_IP6_NF_SECURITY is not set - -# -# Bridge: Netfilter Configuration -# -# CONFIG_BRIDGE_NF_EBTABLES is not set -# CONFIG_IP_DCCP is not set -CONFIG_IP_SCTP=m -# CONFIG_SCTP_DBG_MSG is not set -# CONFIG_SCTP_DBG_OBJCNT is not set -# CONFIG_SCTP_HMAC_NONE is not set -# CONFIG_SCTP_HMAC_SHA1 is not set -CONFIG_SCTP_HMAC_MD5=y -CONFIG_TIPC=m -# CONFIG_TIPC_ADVANCED is not set -# CONFIG_TIPC_DEBUG is not set -CONFIG_ATM=m -CONFIG_ATM_CLIP=m -# CONFIG_ATM_CLIP_NO_ICMP is not set -CONFIG_ATM_LANE=m -CONFIG_ATM_MPOA=m -CONFIG_ATM_BR2684=m -# CONFIG_ATM_BR2684_IPFILTER is not set -CONFIG_STP=m -CONFIG_BRIDGE=m -CONFIG_VLAN_8021Q=m -# CONFIG_VLAN_8021Q_GVRP is not set -# CONFIG_DECNET is not set -CONFIG_LLC=m -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_ECONET is not set -CONFIG_WAN_ROUTER=m -CONFIG_NET_SCHED=y - -# -# Queueing/Scheduling -# -CONFIG_NET_SCH_CBQ=m -CONFIG_NET_SCH_HTB=m -CONFIG_NET_SCH_HFSC=m -CONFIG_NET_SCH_ATM=m -CONFIG_NET_SCH_PRIO=m -CONFIG_NET_SCH_RED=m -CONFIG_NET_SCH_SFQ=m -CONFIG_NET_SCH_TEQL=m -CONFIG_NET_SCH_TBF=m -CONFIG_NET_SCH_GRED=m -CONFIG_NET_SCH_DSMARK=m -CONFIG_NET_SCH_NETEM=m - -# -# Classification -# -CONFIG_NET_CLS=y -# CONFIG_NET_CLS_BASIC is not set -CONFIG_NET_CLS_TCINDEX=m -CONFIG_NET_CLS_ROUTE4=m -CONFIG_NET_CLS_ROUTE=y -CONFIG_NET_CLS_FW=m -CONFIG_NET_CLS_U32=m -# CONFIG_CLS_U32_PERF is not set -# CONFIG_CLS_U32_MARK is not set -CONFIG_NET_CLS_RSVP=m -CONFIG_NET_CLS_RSVP6=m -# CONFIG_NET_CLS_FLOW is not set -# CONFIG_NET_EMATCH is not set -# CONFIG_NET_CLS_ACT is not set -# CONFIG_NET_CLS_IND is not set -CONFIG_NET_SCH_FIFO=y - -# -# Network testing -# -CONFIG_NET_PKTGEN=m -# CONFIG_HAMRADIO is not set -# CONFIG_CAN is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set -# CONFIG_AF_RXRPC is not set -CONFIG_FIB_RULES=y - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set -# CONFIG_RFKILL is not set -# CONFIG_NET_9P is not set - -# -# Device Drivers -# - -# -# Generic Driver Options -# -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" -CONFIG_STANDALONE=y -CONFIG_PREVENT_FIRMWARE_BUILD=y -# CONFIG_FW_LOADER is not set -# CONFIG_DEBUG_DRIVER is not set -# CONFIG_DEBUG_DEVRES is not set -# CONFIG_SYS_HYPERVISOR is not set -# CONFIG_CONNECTOR is not set -CONFIG_MTD=y -# CONFIG_MTD_DEBUG is not set -CONFIG_MTD_CONCAT=y -CONFIG_MTD_PARTITIONS=y -# CONFIG_MTD_REDBOOT_PARTS is not set -# CONFIG_MTD_CMDLINE_PARTS is not set -# CONFIG_MTD_OF_PARTS is not set -# CONFIG_MTD_AR7_PARTS is not set - -# -# User Modules And Translation Layers -# -CONFIG_MTD_CHAR=y -CONFIG_MTD_BLKDEVS=y -CONFIG_MTD_BLOCK=y -# CONFIG_FTL is not set -# CONFIG_NFTL is not set -# CONFIG_INFTL is not set -# CONFIG_RFD_FTL is not set -# CONFIG_SSFDC is not set -# CONFIG_MTD_OOPS is not set - -# -# RAM/ROM/Flash chip drivers -# -CONFIG_MTD_CFI=y -# CONFIG_MTD_JEDECPROBE is not set -CONFIG_MTD_GEN_PROBE=y -CONFIG_MTD_CFI_ADV_OPTIONS=y -# CONFIG_MTD_CFI_NOSWAP is not set -# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set -CONFIG_MTD_CFI_LE_BYTE_SWAP=y -# CONFIG_MTD_CFI_GEOMETRY is not set -CONFIG_MTD_MAP_BANK_WIDTH_1=y -CONFIG_MTD_MAP_BANK_WIDTH_2=y -CONFIG_MTD_MAP_BANK_WIDTH_4=y -# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set -# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set -# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set -CONFIG_MTD_CFI_I1=y -CONFIG_MTD_CFI_I2=y -# CONFIG_MTD_CFI_I4 is not set -# CONFIG_MTD_CFI_I8 is not set -# CONFIG_MTD_OTP is not set -CONFIG_MTD_CFI_INTELEXT=y -# CONFIG_MTD_CFI_AMDSTD is not set -# CONFIG_MTD_CFI_STAA is not set -CONFIG_MTD_CFI_UTIL=y -# CONFIG_MTD_RAM is not set -# CONFIG_MTD_ROM is not set -# CONFIG_MTD_ABSENT is not set - -# -# Mapping drivers for chip access -# -# CONFIG_MTD_COMPLEX_MAPPINGS is not set -# CONFIG_MTD_PHYSMAP is not set -CONFIG_MTD_PHYSMAP_OF=y -# CONFIG_MTD_INTEL_VR_NOR is not set -# CONFIG_MTD_PLATRAM is not set - -# -# Self-contained MTD device drivers -# -# CONFIG_MTD_PMC551 is not set -# CONFIG_MTD_SLRAM is not set -# CONFIG_MTD_PHRAM is not set -# CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLOCK2MTD is not set - -# -# Disk-On-Chip Device Drivers -# -# CONFIG_MTD_DOC2000 is not set -# CONFIG_MTD_DOC2001 is not set -# CONFIG_MTD_DOC2001PLUS is not set -# CONFIG_MTD_NAND is not set -# CONFIG_MTD_ONENAND is not set - -# -# UBI - Unsorted block images -# -# CONFIG_MTD_UBI is not set -CONFIG_OF_DEVICE=y -CONFIG_OF_I2C=y -# CONFIG_PARPORT is not set -CONFIG_BLK_DEV=y -# CONFIG_BLK_DEV_FD is not set -# CONFIG_MAC_FLOPPY is not set -# CONFIG_BLK_CPQ_DA is not set -# CONFIG_BLK_CPQ_CISS_DA is not set -# CONFIG_BLK_DEV_DAC960 is not set -# CONFIG_BLK_DEV_UMEM is not set -# CONFIG_BLK_DEV_COW_COMMON is not set -CONFIG_BLK_DEV_LOOP=m -CONFIG_BLK_DEV_CRYPTOLOOP=m -CONFIG_BLK_DEV_NBD=m -# CONFIG_BLK_DEV_SX8 is not set -CONFIG_BLK_DEV_RAM=y -CONFIG_BLK_DEV_RAM_COUNT=16 -CONFIG_BLK_DEV_RAM_SIZE=4096 -# CONFIG_BLK_DEV_XIP is not set -# CONFIG_CDROM_PKTCDVD is not set -# CONFIG_ATA_OVER_ETH is not set -# CONFIG_BLK_DEV_HD is not set -CONFIG_MISC_DEVICES=y -# CONFIG_PHANTOM is not set -# CONFIG_EEPROM_93CX6 is not set -# CONFIG_SGI_IOC4 is not set -# CONFIG_TIFM_CORE is not set -# CONFIG_ENCLOSURE_SERVICES is not set -# CONFIG_HP_ILO is not set -CONFIG_HAVE_IDE=y -# CONFIG_IDE is not set - -# -# SCSI device support -# -# CONFIG_RAID_ATTRS is not set -# CONFIG_SCSI is not set -# CONFIG_SCSI_DMA is not set -# CONFIG_SCSI_NETLINK is not set -# CONFIG_ATA is not set -CONFIG_MD=y -CONFIG_BLK_DEV_MD=y -CONFIG_MD_LINEAR=y -CONFIG_MD_RAID0=y -CONFIG_MD_RAID1=y -CONFIG_MD_RAID10=y -# CONFIG_MD_RAID456 is not set -CONFIG_MD_MULTIPATH=y -CONFIG_MD_FAULTY=y -CONFIG_BLK_DEV_DM=y -# CONFIG_DM_DEBUG is not set -CONFIG_DM_CRYPT=y -CONFIG_DM_SNAPSHOT=y -CONFIG_DM_MIRROR=y -CONFIG_DM_ZERO=y -# CONFIG_DM_MULTIPATH is not set -# CONFIG_DM_DELAY is not set -# CONFIG_DM_UEVENT is not set -# CONFIG_FUSION is not set - -# -# IEEE 1394 (FireWire) support -# - -# -# Enable only one of the two stacks, unless you know what you are doing -# -# CONFIG_FIREWIRE is not set -# CONFIG_IEEE1394 is not set -# CONFIG_I2O is not set -# CONFIG_MACINTOSH_DRIVERS is not set -CONFIG_NETDEVICES=y -CONFIG_DUMMY=m -CONFIG_BONDING=m -# CONFIG_MACVLAN is not set -# CONFIG_EQUALIZER is not set -CONFIG_TUN=m -# CONFIG_VETH is not set -# CONFIG_ARCNET is not set -CONFIG_PHYLIB=y - -# -# MII PHY device drivers -# -# CONFIG_MARVELL_PHY is not set -# CONFIG_DAVICOM_PHY is not set -# CONFIG_QSEMI_PHY is not set -# CONFIG_LXT_PHY is not set -# CONFIG_CICADA_PHY is not set -# CONFIG_VITESSE_PHY is not set -# CONFIG_SMSC_PHY is not set -CONFIG_BROADCOM_PHY=y -# CONFIG_ICPLUS_PHY is not set -# CONFIG_REALTEK_PHY is not set -# CONFIG_FIXED_PHY is not set -# CONFIG_MDIO_BITBANG is not set -CONFIG_NET_ETHERNET=y -CONFIG_MII=y -# CONFIG_MACE is not set -# CONFIG_BMAC is not set -# CONFIG_HAPPYMEAL is not set -# CONFIG_SUNGEM is not set -# CONFIG_CASSINI is not set -# CONFIG_NET_VENDOR_3COM is not set -# CONFIG_NET_TULIP is not set -# CONFIG_HP100 is not set -# CONFIG_IBM_NEW_EMAC_ZMII is not set -# CONFIG_IBM_NEW_EMAC_RGMII is not set -# CONFIG_IBM_NEW_EMAC_TAH is not set -# CONFIG_IBM_NEW_EMAC_EMAC4 is not set -# CONFIG_NET_PCI is not set -# CONFIG_B44 is not set -CONFIG_NETDEV_1000=y -# CONFIG_ACENIC is not set -# CONFIG_DL2K is not set -# CONFIG_E1000 is not set -# CONFIG_E1000E is not set -# CONFIG_IP1000 is not set -# CONFIG_IGB is not set -# CONFIG_NS83820 is not set -# CONFIG_HAMACHI is not set -# CONFIG_YELLOWFIN is not set -# CONFIG_R8169 is not set -# CONFIG_SIS190 is not set -# CONFIG_SKGE is not set -# CONFIG_SKY2 is not set -# CONFIG_VIA_VELOCITY is not set -# CONFIG_TIGON3 is not set -# CONFIG_BNX2 is not set -CONFIG_GIANFAR=y -# CONFIG_MV643XX_ETH is not set -# CONFIG_QLA3XXX is not set -# CONFIG_ATL1 is not set -# CONFIG_ATL1E is not set -# CONFIG_NETDEV_10000 is not set -# CONFIG_TR is not set - -# -# Wireless LAN -# -# CONFIG_WLAN_PRE80211 is not set -# CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI_LEDS is not set -# CONFIG_WAN is not set -CONFIG_ATM_DRIVERS=y -# CONFIG_ATM_DUMMY is not set -# CONFIG_ATM_TCP is not set -# CONFIG_ATM_LANAI is not set -# CONFIG_ATM_ENI is not set -# CONFIG_ATM_FIRESTREAM is not set -# CONFIG_ATM_ZATM is not set -# CONFIG_ATM_NICSTAR is not set -# CONFIG_ATM_IDT77252 is not set -# CONFIG_ATM_AMBASSADOR is not set -# CONFIG_ATM_HORIZON is not set -# CONFIG_ATM_IA is not set -# CONFIG_ATM_FORE200E is not set -# CONFIG_ATM_HE is not set -# CONFIG_FDDI is not set -# CONFIG_HIPPI is not set -CONFIG_PPP=m -CONFIG_PPP_MULTILINK=y -CONFIG_PPP_FILTER=y -CONFIG_PPP_ASYNC=m -CONFIG_PPP_SYNC_TTY=m -CONFIG_PPP_DEFLATE=m -CONFIG_PPP_BSDCOMP=m -# CONFIG_PPP_MPPE is not set -CONFIG_PPPOE=m -CONFIG_PPPOATM=m -# CONFIG_PPPOL2TP is not set -CONFIG_SLIP=m -CONFIG_SLIP_COMPRESSED=y -CONFIG_SLHC=m -CONFIG_SLIP_SMART=y -CONFIG_SLIP_MODE_SLIP6=y -CONFIG_NETCONSOLE=y -# CONFIG_NETCONSOLE_DYNAMIC is not set -CONFIG_NETPOLL=y -CONFIG_NETPOLL_TRAP=y -CONFIG_NET_POLL_CONTROLLER=y -# CONFIG_ISDN is not set -# CONFIG_PHONE is not set - -# -# Input device support -# -CONFIG_INPUT=y -# CONFIG_INPUT_FF_MEMLESS is not set -# CONFIG_INPUT_POLLDEV is not set - -# -# Userland interfaces -# -CONFIG_INPUT_MOUSEDEV=y -CONFIG_INPUT_MOUSEDEV_PSAUX=y -CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 -CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 -# CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_EVDEV is not set -# CONFIG_INPUT_EVBUG is not set - -# -# Input Device Drivers -# -# CONFIG_INPUT_KEYBOARD is not set -# CONFIG_INPUT_MOUSE is not set -# CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TABLET is not set -# CONFIG_INPUT_TOUCHSCREEN is not set -# CONFIG_INPUT_MISC is not set - -# -# Hardware I/O ports -# -# CONFIG_SERIO is not set -# CONFIG_GAMEPORT is not set - -# -# Character devices -# -CONFIG_VT=y -CONFIG_CONSOLE_TRANSLATIONS=y -CONFIG_VT_CONSOLE=y -CONFIG_HW_CONSOLE=y -# CONFIG_VT_HW_CONSOLE_BINDING is not set -CONFIG_DEVKMEM=y -# CONFIG_SERIAL_NONSTANDARD is not set -# CONFIG_NOZOMI is not set - -# -# Serial drivers -# -CONFIG_SERIAL_8250=y -CONFIG_SERIAL_8250_CONSOLE=y -# CONFIG_SERIAL_8250_PCI is not set -CONFIG_SERIAL_8250_NR_UARTS=2 -CONFIG_SERIAL_8250_RUNTIME_UARTS=2 -# CONFIG_SERIAL_8250_EXTENDED is not set - -# -# Non-8250 serial port support -# -# CONFIG_SERIAL_UARTLITE is not set -CONFIG_SERIAL_CORE=y -CONFIG_SERIAL_CORE_CONSOLE=y -# CONFIG_SERIAL_PMACZILOG is not set -# CONFIG_SERIAL_JSM is not set -# CONFIG_SERIAL_OF_PLATFORM is not set -CONFIG_UNIX98_PTYS=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 -# CONFIG_BRIQ_PANEL is not set -# CONFIG_HVC_RTAS is not set -# CONFIG_IPMI_HANDLER is not set -CONFIG_HW_RANDOM=m -# CONFIG_NVRAM is not set -# CONFIG_GEN_RTC is not set -# CONFIG_R3964 is not set -# CONFIG_APPLICOM is not set -# CONFIG_RAW_DRIVER is not set -# CONFIG_TCG_TPM is not set -CONFIG_DEVPORT=y -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y -CONFIG_I2C_HELPER_AUTO=y - -# -# I2C Hardware Bus support -# - -# -# PC SMBus host controller drivers -# -# CONFIG_I2C_ALI1535 is not set -# CONFIG_I2C_ALI1563 is not set -# CONFIG_I2C_ALI15X3 is not set -# CONFIG_I2C_AMD756 is not set -# CONFIG_I2C_AMD8111 is not set -# CONFIG_I2C_I801 is not set -# CONFIG_I2C_ISCH is not set -# CONFIG_I2C_PIIX4 is not set -# CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_SIS5595 is not set -# CONFIG_I2C_SIS630 is not set -# CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_VIA is not set -# CONFIG_I2C_VIAPRO is not set - -# -# Mac SMBus host controller drivers -# -# CONFIG_I2C_HYDRA is not set -CONFIG_I2C_POWERMAC=y - -# -# I2C system bus drivers (mostly embedded / system-on-chip) -# -CONFIG_I2C_MPC=y -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_SIMTEC is not set - -# -# External I2C/SMBus adapter drivers -# -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_TAOS_EVM is not set - -# -# Graphics adapter I2C/DDC channel drivers -# -# CONFIG_I2C_VOODOO3 is not set - -# -# Other I2C/SMBus bus drivers -# -# CONFIG_I2C_PCA_PLATFORM is not set -# CONFIG_I2C_STUB is not set - -# -# Miscellaneous I2C Chip support -# -# CONFIG_DS1682 is not set -# CONFIG_AT24 is not set -# CONFIG_SENSORS_EEPROM is not set -# CONFIG_SENSORS_PCF8574 is not set -# CONFIG_PCF8575 is not set -# CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_MAX6875 is not set -# CONFIG_SENSORS_TSL2550 is not set -# CONFIG_I2C_DEBUG_CORE is not set -# CONFIG_I2C_DEBUG_ALGO is not set -# CONFIG_I2C_DEBUG_BUS is not set -# CONFIG_I2C_DEBUG_CHIP is not set -# CONFIG_SPI is not set -CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y -# CONFIG_GPIOLIB is not set -# CONFIG_W1 is not set -# CONFIG_POWER_SUPPLY is not set -CONFIG_HWMON=y -# CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_AD7414 is not set -# CONFIG_SENSORS_AD7418 is not set -# CONFIG_SENSORS_ADM1021 is not set -# CONFIG_SENSORS_ADM1025 is not set -# CONFIG_SENSORS_ADM1026 is not set -# CONFIG_SENSORS_ADM1029 is not set -# CONFIG_SENSORS_ADM1031 is not set -# CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ADT7470 is not set -# CONFIG_SENSORS_ADT7473 is not set -# CONFIG_SENSORS_AMS is not set -# CONFIG_SENSORS_ATXP1 is not set -# CONFIG_SENSORS_DS1621 is not set -# CONFIG_SENSORS_I5K_AMB is not set -# CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_F71882FG is not set -# CONFIG_SENSORS_F75375S is not set -# CONFIG_SENSORS_GL518SM is not set -# CONFIG_SENSORS_GL520SM is not set -# CONFIG_SENSORS_IT87 is not set -# CONFIG_SENSORS_LM63 is not set -# CONFIG_SENSORS_LM75 is not set -# CONFIG_SENSORS_LM77 is not set -# CONFIG_SENSORS_LM78 is not set -# CONFIG_SENSORS_LM80 is not set -# CONFIG_SENSORS_LM83 is not set -# CONFIG_SENSORS_LM85 is not set -# CONFIG_SENSORS_LM87 is not set -# CONFIG_SENSORS_LM90 is not set -# CONFIG_SENSORS_LM92 is not set -# CONFIG_SENSORS_LM93 is not set -# CONFIG_SENSORS_MAX1619 is not set -# CONFIG_SENSORS_MAX6650 is not set -# CONFIG_SENSORS_PC87360 is not set -# CONFIG_SENSORS_PC87427 is not set -# CONFIG_SENSORS_SIS5595 is not set -# CONFIG_SENSORS_DME1737 is not set -# CONFIG_SENSORS_SMSC47M1 is not set -# CONFIG_SENSORS_SMSC47M192 is not set -# CONFIG_SENSORS_SMSC47B397 is not set -# CONFIG_SENSORS_ADS7828 is not set -# CONFIG_SENSORS_THMC50 is not set -# CONFIG_SENSORS_VIA686A is not set -# CONFIG_SENSORS_VT1211 is not set -# CONFIG_SENSORS_VT8231 is not set -# CONFIG_SENSORS_W83781D is not set -# CONFIG_SENSORS_W83791D is not set -# CONFIG_SENSORS_W83792D is not set -# CONFIG_SENSORS_W83793 is not set -# CONFIG_SENSORS_W83L785TS is not set -# CONFIG_SENSORS_W83L786NG is not set -# CONFIG_SENSORS_W83627HF is not set -# CONFIG_SENSORS_W83627EHF is not set -# CONFIG_HWMON_DEBUG_CHIP is not set -# CONFIG_THERMAL is not set -# CONFIG_THERMAL_HWMON is not set -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -CONFIG_SOFT_WATCHDOG=m -# CONFIG_ALIM7101_WDT is not set -# CONFIG_8xxx_WDT is not set -# CONFIG_WATCHDOG_RTAS is not set - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set - -# -# Sonics Silicon Backplane -# -CONFIG_SSB_POSSIBLE=y -# CONFIG_SSB is not set - -# -# Multifunction device drivers -# -# CONFIG_MFD_CORE is not set -# CONFIG_MFD_SM501 is not set -# CONFIG_HTC_PASIC3 is not set -# CONFIG_MFD_TMIO is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y - -# -# Graphics support -# -# CONFIG_AGP is not set -# CONFIG_DRM is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set - -# -# Display device support -# -# CONFIG_DISPLAY_SUPPORT is not set - -# -# Console display driver support -# -CONFIG_VGA_CONSOLE=y -# CONFIG_VGACON_SOFT_SCROLLBACK is not set -CONFIG_DUMMY_CONSOLE=y -# CONFIG_SOUND is not set -CONFIG_HID_SUPPORT=y -CONFIG_HID=y -# CONFIG_HID_DEBUG is not set -# CONFIG_HIDRAW is not set -CONFIG_USB_SUPPORT=y -CONFIG_USB_ARCH_HAS_HCD=y -CONFIG_USB_ARCH_HAS_OHCI=y -CONFIG_USB_ARCH_HAS_EHCI=y -# CONFIG_USB is not set -# CONFIG_USB_OTG_WHITELIST is not set -# CONFIG_USB_OTG_BLACKLIST_HUB is not set - -# -# Enable Host or Gadget support to see Inventra options -# - -# -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' -# -# CONFIG_USB_GADGET is not set -# CONFIG_MMC is not set -# CONFIG_MEMSTICK is not set -# CONFIG_NEW_LEDS is not set -# CONFIG_ACCESSIBILITY is not set -# CONFIG_INFINIBAND is not set -# CONFIG_EDAC is not set -# CONFIG_RTC_CLASS is not set -# CONFIG_DMADEVICES is not set -# CONFIG_UIO is not set - -# -# File systems -# -CONFIG_EXT2_FS=y -CONFIG_EXT2_FS_XATTR=y -CONFIG_EXT2_FS_POSIX_ACL=y -# CONFIG_EXT2_FS_SECURITY is not set -# CONFIG_EXT2_FS_XIP is not set -CONFIG_EXT3_FS=y -CONFIG_EXT3_FS_XATTR=y -CONFIG_EXT3_FS_POSIX_ACL=y -# CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set -CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set -CONFIG_FS_MBCACHE=y -CONFIG_REISERFS_FS=m -# CONFIG_REISERFS_CHECK is not set -# CONFIG_REISERFS_PROC_INFO is not set -CONFIG_REISERFS_FS_XATTR=y -CONFIG_REISERFS_FS_POSIX_ACL=y -# CONFIG_REISERFS_FS_SECURITY is not set -# CONFIG_JFS_FS is not set -CONFIG_FS_POSIX_ACL=y -# CONFIG_XFS_FS is not set -CONFIG_OCFS2_FS=m -CONFIG_OCFS2_FS_O2CB=m -CONFIG_OCFS2_FS_STATS=y -CONFIG_OCFS2_DEBUG_MASKLOG=y -# CONFIG_OCFS2_DEBUG_FS is not set -CONFIG_DNOTIFY=y -CONFIG_INOTIFY=y -CONFIG_INOTIFY_USER=y -# CONFIG_QUOTA is not set -CONFIG_AUTOFS_FS=m -CONFIG_AUTOFS4_FS=m -# CONFIG_FUSE_FS is not set - -# -# CD-ROM/DVD Filesystems -# -# CONFIG_ISO9660_FS is not set -# CONFIG_UDF_FS is not set - -# -# DOS/FAT/NT Filesystems -# -# CONFIG_MSDOS_FS is not set -# CONFIG_VFAT_FS is not set -# CONFIG_NTFS_FS is not set - -# -# Pseudo filesystems -# -CONFIG_PROC_FS=y -CONFIG_PROC_KCORE=y -CONFIG_PROC_SYSCTL=y -CONFIG_SYSFS=y -CONFIG_TMPFS=y -# CONFIG_TMPFS_POSIX_ACL is not set -# CONFIG_HUGETLB_PAGE is not set -CONFIG_CONFIGFS_FS=m - -# -# Miscellaneous filesystems -# -# CONFIG_ADFS_FS is not set -# CONFIG_AFFS_FS is not set -# CONFIG_HFS_FS is not set -# CONFIG_HFSPLUS_FS is not set -# CONFIG_BEFS_FS is not set -# CONFIG_BFS_FS is not set -# CONFIG_EFS_FS is not set -# CONFIG_JFFS2_FS is not set -# CONFIG_CRAMFS is not set -# CONFIG_VXFS_FS is not set -CONFIG_MINIX_FS=m -# CONFIG_OMFS_FS is not set -# CONFIG_HPFS_FS is not set -# CONFIG_QNX4FS_FS is not set -CONFIG_ROMFS_FS=m -# CONFIG_SYSV_FS is not set -# CONFIG_UFS_FS is not set -CONFIG_NETWORK_FILESYSTEMS=y -CONFIG_NFS_FS=y -CONFIG_NFS_V3=y -# CONFIG_NFS_V3_ACL is not set -CONFIG_NFS_V4=y -CONFIG_ROOT_NFS=y -# CONFIG_NFSD is not set -CONFIG_LOCKD=y -CONFIG_LOCKD_V4=y -CONFIG_NFS_COMMON=y -CONFIG_SUNRPC=y -CONFIG_SUNRPC_GSS=y -CONFIG_RPCSEC_GSS_KRB5=y -# CONFIG_RPCSEC_GSS_SPKM3 is not set -CONFIG_SMB_FS=m -CONFIG_SMB_NLS_DEFAULT=y -CONFIG_SMB_NLS_REMOTE="cp437" -CONFIG_CIFS=m -# CONFIG_CIFS_STATS is not set -# CONFIG_CIFS_WEAK_PW_HASH is not set -CONFIG_CIFS_XATTR=y -CONFIG_CIFS_POSIX=y -# CONFIG_CIFS_DEBUG2 is not set -# CONFIG_CIFS_EXPERIMENTAL is not set -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_AFS_FS is not set - -# -# Partition Types -# -# CONFIG_PARTITION_ADVANCED is not set -CONFIG_MAC_PARTITION=y -CONFIG_MSDOS_PARTITION=y -CONFIG_NLS=m -CONFIG_NLS_DEFAULT="iso8859-1" -CONFIG_NLS_CODEPAGE_437=m -CONFIG_NLS_CODEPAGE_737=m -CONFIG_NLS_CODEPAGE_775=m -CONFIG_NLS_CODEPAGE_850=m -CONFIG_NLS_CODEPAGE_852=m -CONFIG_NLS_CODEPAGE_855=m -CONFIG_NLS_CODEPAGE_857=m -CONFIG_NLS_CODEPAGE_860=m -CONFIG_NLS_CODEPAGE_861=m -CONFIG_NLS_CODEPAGE_862=m -CONFIG_NLS_CODEPAGE_863=m -CONFIG_NLS_CODEPAGE_864=m -CONFIG_NLS_CODEPAGE_865=m -CONFIG_NLS_CODEPAGE_866=m -CONFIG_NLS_CODEPAGE_869=m -CONFIG_NLS_CODEPAGE_936=m -CONFIG_NLS_CODEPAGE_950=m -CONFIG_NLS_CODEPAGE_932=m -CONFIG_NLS_CODEPAGE_949=m -CONFIG_NLS_CODEPAGE_874=m -CONFIG_NLS_ISO8859_8=m -CONFIG_NLS_CODEPAGE_1250=m -CONFIG_NLS_CODEPAGE_1251=m -CONFIG_NLS_ASCII=m -CONFIG_NLS_ISO8859_1=m -CONFIG_NLS_ISO8859_2=m -CONFIG_NLS_ISO8859_3=m -CONFIG_NLS_ISO8859_4=m -CONFIG_NLS_ISO8859_5=m -CONFIG_NLS_ISO8859_6=m -CONFIG_NLS_ISO8859_7=m -CONFIG_NLS_ISO8859_9=m -CONFIG_NLS_ISO8859_13=m -CONFIG_NLS_ISO8859_14=m -CONFIG_NLS_ISO8859_15=m -CONFIG_NLS_KOI8_R=m -CONFIG_NLS_KOI8_U=m -CONFIG_NLS_UTF8=m -# CONFIG_DLM is not set - -# -# Library routines -# -CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -CONFIG_CRC_CCITT=m -# CONFIG_CRC16 is not set -# CONFIG_CRC_T10DIF is not set -# CONFIG_CRC_ITU_T is not set -CONFIG_CRC32=y -# CONFIG_CRC7 is not set -CONFIG_LIBCRC32C=m -CONFIG_ZLIB_INFLATE=m -CONFIG_ZLIB_DEFLATE=m -CONFIG_PLIST=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HAS_DMA=y -CONFIG_HAVE_LMB=y - -# -# Kernel hacking -# -# CONFIG_PRINTK_TIME is not set -CONFIG_ENABLE_WARN_DEPRECATED=y -CONFIG_ENABLE_MUST_CHECK=y -CONFIG_FRAME_WARN=1024 -CONFIG_MAGIC_SYSRQ=y -# CONFIG_UNUSED_SYMBOLS is not set -CONFIG_DEBUG_FS=y -# CONFIG_HEADERS_CHECK is not set -CONFIG_DEBUG_KERNEL=y -# CONFIG_DEBUG_SHIRQ is not set -CONFIG_DETECT_SOFTLOCKUP=y -# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set -CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 -CONFIG_SCHED_DEBUG=y -# CONFIG_SCHEDSTATS is not set -# CONFIG_TIMER_STATS is not set -# CONFIG_DEBUG_OBJECTS is not set -# CONFIG_DEBUG_SLAB is not set -# CONFIG_DEBUG_RT_MUTEXES is not set -# CONFIG_RT_MUTEX_TESTER is not set -# CONFIG_DEBUG_SPINLOCK is not set -# CONFIG_DEBUG_MUTEXES is not set -# CONFIG_DEBUG_SPINLOCK_SLEEP is not set -# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set -# CONFIG_DEBUG_KOBJECT is not set -# CONFIG_DEBUG_BUGVERBOSE is not set -CONFIG_DEBUG_INFO=y -# CONFIG_DEBUG_VM is not set -# CONFIG_DEBUG_WRITECOUNT is not set -# CONFIG_DEBUG_MEMORY_INIT is not set -# CONFIG_DEBUG_LIST is not set -# CONFIG_DEBUG_SG is not set -# CONFIG_BOOT_PRINTK_DELAY is not set -# CONFIG_RCU_TORTURE_TEST is not set -# CONFIG_BACKTRACE_SELF_TEST is not set -# CONFIG_FAULT_INJECTION is not set -# CONFIG_LATENCYTOP is not set -CONFIG_SYSCTL_SYSCALL_CHECK=y -CONFIG_HAVE_FTRACE=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -# CONFIG_FTRACE is not set -# CONFIG_PREEMPT_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_SAMPLES is not set -CONFIG_HAVE_ARCH_KGDB=y -# CONFIG_KGDB is not set -# CONFIG_DEBUG_STACKOVERFLOW is not set -# CONFIG_DEBUG_STACK_USAGE is not set -# CONFIG_DEBUG_PAGEALLOC is not set -# CONFIG_CODE_PATCHING_SELFTEST is not set -# CONFIG_FTR_FIXUP_SELFTEST is not set -# CONFIG_XMON is not set -# CONFIG_IRQSTACKS is not set -# CONFIG_VIRQ_DEBUG is not set -# CONFIG_BDI_SWITCH is not set -# CONFIG_BOOTX_TEXT is not set -# CONFIG_PPC_EARLY_DEBUG is not set - -# -# Security options -# -# CONFIG_KEYS is not set -CONFIG_SECURITY=y -CONFIG_SECURITY_NETWORK=y -# CONFIG_SECURITY_NETWORK_XFRM is not set -# CONFIG_SECURITY_FILE_CAPABILITIES is not set -CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0 -CONFIG_CRYPTO=y - -# -# Crypto core or helper -# -CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m -CONFIG_CRYPTO_BLKCIPHER=y -CONFIG_CRYPTO_HASH=y -CONFIG_CRYPTO_MANAGER=y -# CONFIG_CRYPTO_GF128MUL is not set -CONFIG_CRYPTO_NULL=m -# CONFIG_CRYPTO_CRYPTD is not set -CONFIG_CRYPTO_AUTHENC=m -CONFIG_CRYPTO_TEST=m - -# -# Authenticated Encryption with Associated Data -# -# CONFIG_CRYPTO_CCM is not set -# CONFIG_CRYPTO_GCM is not set -# CONFIG_CRYPTO_SEQIV is not set - -# -# Block modes -# -CONFIG_CRYPTO_CBC=y -# CONFIG_CRYPTO_CTR is not set -# CONFIG_CRYPTO_CTS is not set -CONFIG_CRYPTO_ECB=m -# CONFIG_CRYPTO_LRW is not set -CONFIG_CRYPTO_PCBC=m -# CONFIG_CRYPTO_XTS is not set - -# -# Hash modes -# -CONFIG_CRYPTO_HMAC=y -# CONFIG_CRYPTO_XCBC is not set - -# -# Digest -# -CONFIG_CRYPTO_CRC32C=m -CONFIG_CRYPTO_MD4=m -CONFIG_CRYPTO_MD5=y -CONFIG_CRYPTO_MICHAEL_MIC=m -# CONFIG_CRYPTO_RMD128 is not set -# CONFIG_CRYPTO_RMD160 is not set -# CONFIG_CRYPTO_RMD256 is not set -# CONFIG_CRYPTO_RMD320 is not set -CONFIG_CRYPTO_SHA1=m -CONFIG_CRYPTO_SHA256=m -CONFIG_CRYPTO_SHA512=m -# CONFIG_CRYPTO_TGR192 is not set -CONFIG_CRYPTO_WP512=m - -# -# Ciphers -# -CONFIG_CRYPTO_AES=m -CONFIG_CRYPTO_ANUBIS=m -CONFIG_CRYPTO_ARC4=m -CONFIG_CRYPTO_BLOWFISH=m -# CONFIG_CRYPTO_CAMELLIA is not set -CONFIG_CRYPTO_CAST5=m -CONFIG_CRYPTO_CAST6=m -CONFIG_CRYPTO_DES=y -# CONFIG_CRYPTO_FCRYPT is not set -CONFIG_CRYPTO_KHAZAD=m -# CONFIG_CRYPTO_SALSA20 is not set -# CONFIG_CRYPTO_SEED is not set -CONFIG_CRYPTO_SERPENT=m -CONFIG_CRYPTO_TEA=m -CONFIG_CRYPTO_TWOFISH=m -CONFIG_CRYPTO_TWOFISH_COMMON=m - -# -# Compression -# -CONFIG_CRYPTO_DEFLATE=m -# CONFIG_CRYPTO_LZO is not set -CONFIG_CRYPTO_HW=y -# CONFIG_CRYPTO_DEV_HIFN_795X is not set -# CONFIG_CRYPTO_DEV_TALITOS is not set -# CONFIG_PPC_CLOCK is not set -# CONFIG_VIRTUALIZATION is not set -- cgit v1.2.3 From 782f04fc0c2af3c1e92c9d561926a2056b1c72e8 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 23 Sep 2008 23:36:32 -0500 Subject: powerpc: Move 8xxx GPIO Kconfig under the platform menu The initial patch had the option at the top level which wasn't quite right. Moving under the platform options is a bit better. Signed-off-by: Kumar Gala --- arch/powerpc/platforms/Kconfig | 9 +++++++++ arch/powerpc/sysdev/Kconfig | 9 --------- 2 files changed, 9 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig index 4c900efa164..9578c45b04f 100644 --- a/arch/powerpc/platforms/Kconfig +++ b/arch/powerpc/platforms/Kconfig @@ -293,4 +293,13 @@ config OF_RTC source "arch/powerpc/sysdev/bestcomm/Kconfig" +config MPC8xxx_GPIO + bool "MPC8xxx GPIO support" + depends on PPC_MPC831x || PPC_MPC834x || PPC_MPC837x || PPC_85xx || PPC_86xx + select GENERIC_GPIO + select ARCH_REQUIRE_GPIOLIB + help + Say Y here if you're going to use hardware that connects to the + MPC831x/834x/837x/8572/8610 GPIOs. + endmenu diff --git a/arch/powerpc/sysdev/Kconfig b/arch/powerpc/sysdev/Kconfig index d0e7bb05c3a..396582835cb 100644 --- a/arch/powerpc/sysdev/Kconfig +++ b/arch/powerpc/sysdev/Kconfig @@ -7,15 +7,6 @@ config PPC4xx_PCI_EXPRESS depends on PCI && 4xx default n -config MPC8xxx_GPIO - bool "MPC8xxx GPIO support" - depends on PPC_MPC831x || PPC_MPC834x || PPC_MPC837x || PPC_85xx || PPC_86xx - select GENERIC_GPIO - select ARCH_REQUIRE_GPIOLIB - help - Say Y here if you're going to use hardware that connects to the - MPC831x/834x/837x/8572/8610 GPIOs. - config PPC_MSI_BITMAP bool depends on PCI_MSI -- cgit v1.2.3 From 7c05d7e08d907d66b8e18515572f42c71fb709fe Mon Sep 17 00:00:00 2001 From: Becky Bruce Date: Mon, 8 Sep 2008 09:09:52 +0000 Subject: powerpc: Rename dma_64.c to dma.c This is in preparation for the merge of the 32 and 64-bit dma code in arch/powerpc. Signed-off-by: Becky Bruce Signed-off-by: Kumar Gala --- arch/powerpc/kernel/Makefile | 2 +- arch/powerpc/kernel/dma.c | 200 +++++++++++++++++++++++++++++++++++++++++++ arch/powerpc/kernel/dma_64.c | 200 ------------------------------------------- 3 files changed, 201 insertions(+), 201 deletions(-) create mode 100644 arch/powerpc/kernel/dma.c delete mode 100644 arch/powerpc/kernel/dma_64.c (limited to 'arch') diff --git a/arch/powerpc/kernel/Makefile b/arch/powerpc/kernel/Makefile index 16326fd92f9..ab7d4cbf1e0 100644 --- a/arch/powerpc/kernel/Makefile +++ b/arch/powerpc/kernel/Makefile @@ -73,7 +73,7 @@ obj-y += time.o prom.o traps.o setup-common.o \ udbg.o misc.o io.o \ misc_$(CONFIG_WORD_SIZE).o obj-$(CONFIG_PPC32) += entry_32.o setup_32.o -obj-$(CONFIG_PPC64) += dma_64.o iommu.o +obj-$(CONFIG_PPC64) += dma.o iommu.o obj-$(CONFIG_KGDB) += kgdb.o obj-$(CONFIG_PPC_MULTIPLATFORM) += prom_init.o obj-$(CONFIG_MODULES) += ppc_ksyms.o diff --git a/arch/powerpc/kernel/dma.c b/arch/powerpc/kernel/dma.c new file mode 100644 index 00000000000..ae5708e3a31 --- /dev/null +++ b/arch/powerpc/kernel/dma.c @@ -0,0 +1,200 @@ +/* + * Copyright (C) 2006 Benjamin Herrenschmidt, IBM Corporation + * + * Provide default implementations of the DMA mapping callbacks for + * directly mapped busses and busses using the iommu infrastructure + */ + +#include +#include +#include +#include +#include + +/* + * Generic iommu implementation + */ + +/* Allocates a contiguous real buffer and creates mappings over it. + * Returns the virtual address of the buffer and sets dma_handle + * to the dma address (mapping) of the first page. + */ +static void *dma_iommu_alloc_coherent(struct device *dev, size_t size, + dma_addr_t *dma_handle, gfp_t flag) +{ + return iommu_alloc_coherent(dev, dev->archdata.dma_data, size, + dma_handle, device_to_mask(dev), flag, + dev->archdata.numa_node); +} + +static void dma_iommu_free_coherent(struct device *dev, size_t size, + void *vaddr, dma_addr_t dma_handle) +{ + iommu_free_coherent(dev->archdata.dma_data, size, vaddr, dma_handle); +} + +/* Creates TCEs for a user provided buffer. The user buffer must be + * contiguous real kernel storage (not vmalloc). The address of the buffer + * passed here is the kernel (virtual) address of the buffer. The buffer + * need not be page aligned, the dma_addr_t returned will point to the same + * byte within the page as vaddr. + */ +static dma_addr_t dma_iommu_map_single(struct device *dev, void *vaddr, + size_t size, + enum dma_data_direction direction, + struct dma_attrs *attrs) +{ + return iommu_map_single(dev, dev->archdata.dma_data, vaddr, size, + device_to_mask(dev), direction, attrs); +} + + +static void dma_iommu_unmap_single(struct device *dev, dma_addr_t dma_handle, + size_t size, + enum dma_data_direction direction, + struct dma_attrs *attrs) +{ + iommu_unmap_single(dev->archdata.dma_data, dma_handle, size, direction, + attrs); +} + + +static int dma_iommu_map_sg(struct device *dev, struct scatterlist *sglist, + int nelems, enum dma_data_direction direction, + struct dma_attrs *attrs) +{ + return iommu_map_sg(dev, dev->archdata.dma_data, sglist, nelems, + device_to_mask(dev), direction, attrs); +} + +static void dma_iommu_unmap_sg(struct device *dev, struct scatterlist *sglist, + int nelems, enum dma_data_direction direction, + struct dma_attrs *attrs) +{ + iommu_unmap_sg(dev->archdata.dma_data, sglist, nelems, direction, + attrs); +} + +/* We support DMA to/from any memory page via the iommu */ +static int dma_iommu_dma_supported(struct device *dev, u64 mask) +{ + struct iommu_table *tbl = dev->archdata.dma_data; + + if (!tbl || tbl->it_offset > mask) { + printk(KERN_INFO + "Warning: IOMMU offset too big for device mask\n"); + if (tbl) + printk(KERN_INFO + "mask: 0x%08lx, table offset: 0x%08lx\n", + mask, tbl->it_offset); + else + printk(KERN_INFO "mask: 0x%08lx, table unavailable\n", + mask); + return 0; + } else + return 1; +} + +struct dma_mapping_ops dma_iommu_ops = { + .alloc_coherent = dma_iommu_alloc_coherent, + .free_coherent = dma_iommu_free_coherent, + .map_single = dma_iommu_map_single, + .unmap_single = dma_iommu_unmap_single, + .map_sg = dma_iommu_map_sg, + .unmap_sg = dma_iommu_unmap_sg, + .dma_supported = dma_iommu_dma_supported, +}; +EXPORT_SYMBOL(dma_iommu_ops); + +/* + * Generic direct DMA implementation + * + * This implementation supports a per-device offset that can be applied if + * the address at which memory is visible to devices is not 0. Platform code + * can set archdata.dma_data to an unsigned long holding the offset. By + * default the offset is zero. + */ + +static unsigned long get_dma_direct_offset(struct device *dev) +{ + return (unsigned long)dev->archdata.dma_data; +} + +static void *dma_direct_alloc_coherent(struct device *dev, size_t size, + dma_addr_t *dma_handle, gfp_t flag) +{ + struct page *page; + void *ret; + int node = dev->archdata.numa_node; + + page = alloc_pages_node(node, flag, get_order(size)); + if (page == NULL) + return NULL; + ret = page_address(page); + memset(ret, 0, size); + *dma_handle = virt_to_abs(ret) + get_dma_direct_offset(dev); + + return ret; +} + +static void dma_direct_free_coherent(struct device *dev, size_t size, + void *vaddr, dma_addr_t dma_handle) +{ + free_pages((unsigned long)vaddr, get_order(size)); +} + +static dma_addr_t dma_direct_map_single(struct device *dev, void *ptr, + size_t size, + enum dma_data_direction direction, + struct dma_attrs *attrs) +{ + return virt_to_abs(ptr) + get_dma_direct_offset(dev); +} + +static void dma_direct_unmap_single(struct device *dev, dma_addr_t dma_addr, + size_t size, + enum dma_data_direction direction, + struct dma_attrs *attrs) +{ +} + +static int dma_direct_map_sg(struct device *dev, struct scatterlist *sgl, + int nents, enum dma_data_direction direction, + struct dma_attrs *attrs) +{ + struct scatterlist *sg; + int i; + + for_each_sg(sgl, sg, nents, i) { + sg->dma_address = sg_phys(sg) + get_dma_direct_offset(dev); + sg->dma_length = sg->length; + } + + return nents; +} + +static void dma_direct_unmap_sg(struct device *dev, struct scatterlist *sg, + int nents, enum dma_data_direction direction, + struct dma_attrs *attrs) +{ +} + +static int dma_direct_dma_supported(struct device *dev, u64 mask) +{ + /* Could be improved to check for memory though it better be + * done via some global so platforms can set the limit in case + * they have limited DMA windows + */ + return mask >= DMA_32BIT_MASK; +} + +struct dma_mapping_ops dma_direct_ops = { + .alloc_coherent = dma_direct_alloc_coherent, + .free_coherent = dma_direct_free_coherent, + .map_single = dma_direct_map_single, + .unmap_single = dma_direct_unmap_single, + .map_sg = dma_direct_map_sg, + .unmap_sg = dma_direct_unmap_sg, + .dma_supported = dma_direct_dma_supported, +}; +EXPORT_SYMBOL(dma_direct_ops); diff --git a/arch/powerpc/kernel/dma_64.c b/arch/powerpc/kernel/dma_64.c deleted file mode 100644 index ae5708e3a31..00000000000 --- a/arch/powerpc/kernel/dma_64.c +++ /dev/null @@ -1,200 +0,0 @@ -/* - * Copyright (C) 2006 Benjamin Herrenschmidt, IBM Corporation - * - * Provide default implementations of the DMA mapping callbacks for - * directly mapped busses and busses using the iommu infrastructure - */ - -#include -#include -#include -#include -#include - -/* - * Generic iommu implementation - */ - -/* Allocates a contiguous real buffer and creates mappings over it. - * Returns the virtual address of the buffer and sets dma_handle - * to the dma address (mapping) of the first page. - */ -static void *dma_iommu_alloc_coherent(struct device *dev, size_t size, - dma_addr_t *dma_handle, gfp_t flag) -{ - return iommu_alloc_coherent(dev, dev->archdata.dma_data, size, - dma_handle, device_to_mask(dev), flag, - dev->archdata.numa_node); -} - -static void dma_iommu_free_coherent(struct device *dev, size_t size, - void *vaddr, dma_addr_t dma_handle) -{ - iommu_free_coherent(dev->archdata.dma_data, size, vaddr, dma_handle); -} - -/* Creates TCEs for a user provided buffer. The user buffer must be - * contiguous real kernel storage (not vmalloc). The address of the buffer - * passed here is the kernel (virtual) address of the buffer. The buffer - * need not be page aligned, the dma_addr_t returned will point to the same - * byte within the page as vaddr. - */ -static dma_addr_t dma_iommu_map_single(struct device *dev, void *vaddr, - size_t size, - enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - return iommu_map_single(dev, dev->archdata.dma_data, vaddr, size, - device_to_mask(dev), direction, attrs); -} - - -static void dma_iommu_unmap_single(struct device *dev, dma_addr_t dma_handle, - size_t size, - enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - iommu_unmap_single(dev->archdata.dma_data, dma_handle, size, direction, - attrs); -} - - -static int dma_iommu_map_sg(struct device *dev, struct scatterlist *sglist, - int nelems, enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - return iommu_map_sg(dev, dev->archdata.dma_data, sglist, nelems, - device_to_mask(dev), direction, attrs); -} - -static void dma_iommu_unmap_sg(struct device *dev, struct scatterlist *sglist, - int nelems, enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - iommu_unmap_sg(dev->archdata.dma_data, sglist, nelems, direction, - attrs); -} - -/* We support DMA to/from any memory page via the iommu */ -static int dma_iommu_dma_supported(struct device *dev, u64 mask) -{ - struct iommu_table *tbl = dev->archdata.dma_data; - - if (!tbl || tbl->it_offset > mask) { - printk(KERN_INFO - "Warning: IOMMU offset too big for device mask\n"); - if (tbl) - printk(KERN_INFO - "mask: 0x%08lx, table offset: 0x%08lx\n", - mask, tbl->it_offset); - else - printk(KERN_INFO "mask: 0x%08lx, table unavailable\n", - mask); - return 0; - } else - return 1; -} - -struct dma_mapping_ops dma_iommu_ops = { - .alloc_coherent = dma_iommu_alloc_coherent, - .free_coherent = dma_iommu_free_coherent, - .map_single = dma_iommu_map_single, - .unmap_single = dma_iommu_unmap_single, - .map_sg = dma_iommu_map_sg, - .unmap_sg = dma_iommu_unmap_sg, - .dma_supported = dma_iommu_dma_supported, -}; -EXPORT_SYMBOL(dma_iommu_ops); - -/* - * Generic direct DMA implementation - * - * This implementation supports a per-device offset that can be applied if - * the address at which memory is visible to devices is not 0. Platform code - * can set archdata.dma_data to an unsigned long holding the offset. By - * default the offset is zero. - */ - -static unsigned long get_dma_direct_offset(struct device *dev) -{ - return (unsigned long)dev->archdata.dma_data; -} - -static void *dma_direct_alloc_coherent(struct device *dev, size_t size, - dma_addr_t *dma_handle, gfp_t flag) -{ - struct page *page; - void *ret; - int node = dev->archdata.numa_node; - - page = alloc_pages_node(node, flag, get_order(size)); - if (page == NULL) - return NULL; - ret = page_address(page); - memset(ret, 0, size); - *dma_handle = virt_to_abs(ret) + get_dma_direct_offset(dev); - - return ret; -} - -static void dma_direct_free_coherent(struct device *dev, size_t size, - void *vaddr, dma_addr_t dma_handle) -{ - free_pages((unsigned long)vaddr, get_order(size)); -} - -static dma_addr_t dma_direct_map_single(struct device *dev, void *ptr, - size_t size, - enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - return virt_to_abs(ptr) + get_dma_direct_offset(dev); -} - -static void dma_direct_unmap_single(struct device *dev, dma_addr_t dma_addr, - size_t size, - enum dma_data_direction direction, - struct dma_attrs *attrs) -{ -} - -static int dma_direct_map_sg(struct device *dev, struct scatterlist *sgl, - int nents, enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - struct scatterlist *sg; - int i; - - for_each_sg(sgl, sg, nents, i) { - sg->dma_address = sg_phys(sg) + get_dma_direct_offset(dev); - sg->dma_length = sg->length; - } - - return nents; -} - -static void dma_direct_unmap_sg(struct device *dev, struct scatterlist *sg, - int nents, enum dma_data_direction direction, - struct dma_attrs *attrs) -{ -} - -static int dma_direct_dma_supported(struct device *dev, u64 mask) -{ - /* Could be improved to check for memory though it better be - * done via some global so platforms can set the limit in case - * they have limited DMA windows - */ - return mask >= DMA_32BIT_MASK; -} - -struct dma_mapping_ops dma_direct_ops = { - .alloc_coherent = dma_direct_alloc_coherent, - .free_coherent = dma_direct_free_coherent, - .map_single = dma_direct_map_single, - .unmap_single = dma_direct_unmap_single, - .map_sg = dma_direct_map_sg, - .unmap_sg = dma_direct_unmap_sg, - .dma_supported = dma_direct_dma_supported, -}; -EXPORT_SYMBOL(dma_direct_ops); -- cgit v1.2.3 From 8dd0e95206f7c33bed2aed33ac668335174684e8 Mon Sep 17 00:00:00 2001 From: Becky Bruce Date: Mon, 8 Sep 2008 09:09:53 +0000 Subject: powerpc: Move iommu dma ops from dma.c to dma-iommu.c 32-bit platforms are about to start using dma.c; move the iommu dma ops into their own file to make this a bit cleaner. Signed-off-by: Becky Bruce Signed-off-by: Kumar Gala --- arch/powerpc/kernel/Makefile | 2 +- arch/powerpc/kernel/dma-iommu.c | 103 ++++++++++++++++++++++++++++++++++++++++ arch/powerpc/kernel/dma.c | 98 +------------------------------------- 3 files changed, 105 insertions(+), 98 deletions(-) create mode 100644 arch/powerpc/kernel/dma-iommu.c (limited to 'arch') diff --git a/arch/powerpc/kernel/Makefile b/arch/powerpc/kernel/Makefile index ab7d4cbf1e0..09b3cabf2f9 100644 --- a/arch/powerpc/kernel/Makefile +++ b/arch/powerpc/kernel/Makefile @@ -73,7 +73,7 @@ obj-y += time.o prom.o traps.o setup-common.o \ udbg.o misc.o io.o \ misc_$(CONFIG_WORD_SIZE).o obj-$(CONFIG_PPC32) += entry_32.o setup_32.o -obj-$(CONFIG_PPC64) += dma.o iommu.o +obj-$(CONFIG_PPC64) += dma.o dma-iommu.o iommu.o obj-$(CONFIG_KGDB) += kgdb.o obj-$(CONFIG_PPC_MULTIPLATFORM) += prom_init.o obj-$(CONFIG_MODULES) += ppc_ksyms.o diff --git a/arch/powerpc/kernel/dma-iommu.c b/arch/powerpc/kernel/dma-iommu.c new file mode 100644 index 00000000000..01091f1d508 --- /dev/null +++ b/arch/powerpc/kernel/dma-iommu.c @@ -0,0 +1,103 @@ +/* + * Copyright (C) 2006 Benjamin Herrenschmidt, IBM Corporation + * + * Provide default implementations of the DMA mapping callbacks for + * busses using the iommu infrastructure + */ + +#include + +/* + * Generic iommu implementation + */ + +/* Allocates a contiguous real buffer and creates mappings over it. + * Returns the virtual address of the buffer and sets dma_handle + * to the dma address (mapping) of the first page. + */ +static void *dma_iommu_alloc_coherent(struct device *dev, size_t size, + dma_addr_t *dma_handle, gfp_t flag) +{ + return iommu_alloc_coherent(dev, dev->archdata.dma_data, size, + dma_handle, device_to_mask(dev), flag, + dev->archdata.numa_node); +} + +static void dma_iommu_free_coherent(struct device *dev, size_t size, + void *vaddr, dma_addr_t dma_handle) +{ + iommu_free_coherent(dev->archdata.dma_data, size, vaddr, dma_handle); +} + +/* Creates TCEs for a user provided buffer. The user buffer must be + * contiguous real kernel storage (not vmalloc). The address of the buffer + * passed here is the kernel (virtual) address of the buffer. The buffer + * need not be page aligned, the dma_addr_t returned will point to the same + * byte within the page as vaddr. + */ +static dma_addr_t dma_iommu_map_single(struct device *dev, void *vaddr, + size_t size, + enum dma_data_direction direction, + struct dma_attrs *attrs) +{ + return iommu_map_single(dev, dev->archdata.dma_data, vaddr, size, + device_to_mask(dev), direction, attrs); +} + + +static void dma_iommu_unmap_single(struct device *dev, dma_addr_t dma_handle, + size_t size, + enum dma_data_direction direction, + struct dma_attrs *attrs) +{ + iommu_unmap_single(dev->archdata.dma_data, dma_handle, size, direction, + attrs); +} + + +static int dma_iommu_map_sg(struct device *dev, struct scatterlist *sglist, + int nelems, enum dma_data_direction direction, + struct dma_attrs *attrs) +{ + return iommu_map_sg(dev, dev->archdata.dma_data, sglist, nelems, + device_to_mask(dev), direction, attrs); +} + +static void dma_iommu_unmap_sg(struct device *dev, struct scatterlist *sglist, + int nelems, enum dma_data_direction direction, + struct dma_attrs *attrs) +{ + iommu_unmap_sg(dev->archdata.dma_data, sglist, nelems, direction, + attrs); +} + +/* We support DMA to/from any memory page via the iommu */ +static int dma_iommu_dma_supported(struct device *dev, u64 mask) +{ + struct iommu_table *tbl = dev->archdata.dma_data; + + if (!tbl || tbl->it_offset > mask) { + printk(KERN_INFO + "Warning: IOMMU offset too big for device mask\n"); + if (tbl) + printk(KERN_INFO + "mask: 0x%08lx, table offset: 0x%08lx\n", + mask, tbl->it_offset); + else + printk(KERN_INFO "mask: 0x%08lx, table unavailable\n", + mask); + return 0; + } else + return 1; +} + +struct dma_mapping_ops dma_iommu_ops = { + .alloc_coherent = dma_iommu_alloc_coherent, + .free_coherent = dma_iommu_free_coherent, + .map_single = dma_iommu_map_single, + .unmap_single = dma_iommu_unmap_single, + .map_sg = dma_iommu_map_sg, + .unmap_sg = dma_iommu_unmap_sg, + .dma_supported = dma_iommu_dma_supported, +}; +EXPORT_SYMBOL(dma_iommu_ops); diff --git a/arch/powerpc/kernel/dma.c b/arch/powerpc/kernel/dma.c index ae5708e3a31..44e3486419e 100644 --- a/arch/powerpc/kernel/dma.c +++ b/arch/powerpc/kernel/dma.c @@ -2,110 +2,14 @@ * Copyright (C) 2006 Benjamin Herrenschmidt, IBM Corporation * * Provide default implementations of the DMA mapping callbacks for - * directly mapped busses and busses using the iommu infrastructure + * directly mapped busses. */ #include #include #include -#include #include -/* - * Generic iommu implementation - */ - -/* Allocates a contiguous real buffer and creates mappings over it. - * Returns the virtual address of the buffer and sets dma_handle - * to the dma address (mapping) of the first page. - */ -static void *dma_iommu_alloc_coherent(struct device *dev, size_t size, - dma_addr_t *dma_handle, gfp_t flag) -{ - return iommu_alloc_coherent(dev, dev->archdata.dma_data, size, - dma_handle, device_to_mask(dev), flag, - dev->archdata.numa_node); -} - -static void dma_iommu_free_coherent(struct device *dev, size_t size, - void *vaddr, dma_addr_t dma_handle) -{ - iommu_free_coherent(dev->archdata.dma_data, size, vaddr, dma_handle); -} - -/* Creates TCEs for a user provided buffer. The user buffer must be - * contiguous real kernel storage (not vmalloc). The address of the buffer - * passed here is the kernel (virtual) address of the buffer. The buffer - * need not be page aligned, the dma_addr_t returned will point to the same - * byte within the page as vaddr. - */ -static dma_addr_t dma_iommu_map_single(struct device *dev, void *vaddr, - size_t size, - enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - return iommu_map_single(dev, dev->archdata.dma_data, vaddr, size, - device_to_mask(dev), direction, attrs); -} - - -static void dma_iommu_unmap_single(struct device *dev, dma_addr_t dma_handle, - size_t size, - enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - iommu_unmap_single(dev->archdata.dma_data, dma_handle, size, direction, - attrs); -} - - -static int dma_iommu_map_sg(struct device *dev, struct scatterlist *sglist, - int nelems, enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - return iommu_map_sg(dev, dev->archdata.dma_data, sglist, nelems, - device_to_mask(dev), direction, attrs); -} - -static void dma_iommu_unmap_sg(struct device *dev, struct scatterlist *sglist, - int nelems, enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - iommu_unmap_sg(dev->archdata.dma_data, sglist, nelems, direction, - attrs); -} - -/* We support DMA to/from any memory page via the iommu */ -static int dma_iommu_dma_supported(struct device *dev, u64 mask) -{ - struct iommu_table *tbl = dev->archdata.dma_data; - - if (!tbl || tbl->it_offset > mask) { - printk(KERN_INFO - "Warning: IOMMU offset too big for device mask\n"); - if (tbl) - printk(KERN_INFO - "mask: 0x%08lx, table offset: 0x%08lx\n", - mask, tbl->it_offset); - else - printk(KERN_INFO "mask: 0x%08lx, table unavailable\n", - mask); - return 0; - } else - return 1; -} - -struct dma_mapping_ops dma_iommu_ops = { - .alloc_coherent = dma_iommu_alloc_coherent, - .free_coherent = dma_iommu_free_coherent, - .map_single = dma_iommu_map_single, - .unmap_single = dma_iommu_unmap_single, - .map_sg = dma_iommu_map_sg, - .unmap_sg = dma_iommu_unmap_sg, - .dma_supported = dma_iommu_dma_supported, -}; -EXPORT_SYMBOL(dma_iommu_ops); - /* * Generic direct DMA implementation * -- cgit v1.2.3 From 8fae0353247530d2124b2419052fa6120462fa99 Mon Sep 17 00:00:00 2001 From: Becky Bruce Date: Mon, 8 Sep 2008 09:09:54 +0000 Subject: powerpc: Drop archdata numa_node Use the struct device's numa_node instead; use accessor functions to get/set numa_node. Signed-off-by: Becky Bruce Signed-off-by: Kumar Gala --- arch/powerpc/include/asm/device.h | 3 --- arch/powerpc/kernel/dma-iommu.c | 2 +- arch/powerpc/kernel/dma.c | 2 +- arch/powerpc/kernel/of_device.c | 2 +- arch/powerpc/kernel/pci_64.c | 7 ++----- arch/powerpc/kernel/vio.c | 2 +- arch/powerpc/platforms/cell/iommu.c | 6 +++--- arch/powerpc/platforms/ps3/system-bus.c | 2 +- 8 files changed, 10 insertions(+), 16 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/device.h b/arch/powerpc/include/asm/device.h index 228ab2a315b..dfd504caccc 100644 --- a/arch/powerpc/include/asm/device.h +++ b/arch/powerpc/include/asm/device.h @@ -16,9 +16,6 @@ struct dev_archdata { /* DMA operations on that device */ struct dma_mapping_ops *dma_ops; void *dma_data; - - /* NUMA node if applicable */ - int numa_node; }; #endif /* _ASM_POWERPC_DEVICE_H */ diff --git a/arch/powerpc/kernel/dma-iommu.c b/arch/powerpc/kernel/dma-iommu.c index 01091f1d508..49248f89ce2 100644 --- a/arch/powerpc/kernel/dma-iommu.c +++ b/arch/powerpc/kernel/dma-iommu.c @@ -20,7 +20,7 @@ static void *dma_iommu_alloc_coherent(struct device *dev, size_t size, { return iommu_alloc_coherent(dev, dev->archdata.dma_data, size, dma_handle, device_to_mask(dev), flag, - dev->archdata.numa_node); + dev_to_node(dev)); } static void dma_iommu_free_coherent(struct device *dev, size_t size, diff --git a/arch/powerpc/kernel/dma.c b/arch/powerpc/kernel/dma.c index 44e3486419e..124f86743bd 100644 --- a/arch/powerpc/kernel/dma.c +++ b/arch/powerpc/kernel/dma.c @@ -29,7 +29,7 @@ static void *dma_direct_alloc_coherent(struct device *dev, size_t size, { struct page *page; void *ret; - int node = dev->archdata.numa_node; + int node = dev_to_node(dev); page = alloc_pages_node(node, flag, get_order(size)); if (page == NULL) diff --git a/arch/powerpc/kernel/of_device.c b/arch/powerpc/kernel/of_device.c index e9be908f199..93ae5b169f4 100644 --- a/arch/powerpc/kernel/of_device.c +++ b/arch/powerpc/kernel/of_device.c @@ -78,7 +78,7 @@ struct of_device *of_device_alloc(struct device_node *np, dev->dev.parent = parent; dev->dev.release = of_release_dev; dev->dev.archdata.of_node = np; - dev->dev.archdata.numa_node = of_node_to_nid(np); + set_dev_node(&dev->dev, of_node_to_nid(np)); if (bus_id) strlcpy(dev->dev.bus_id, bus_id, BUS_ID_SIZE); diff --git a/arch/powerpc/kernel/pci_64.c b/arch/powerpc/kernel/pci_64.c index 30eedfc5a56..1f75bf03446 100644 --- a/arch/powerpc/kernel/pci_64.c +++ b/arch/powerpc/kernel/pci_64.c @@ -558,11 +558,8 @@ void __devinit pcibios_setup_new_device(struct pci_dev *dev) sd->of_node ? sd->of_node->full_name : ""); sd->dma_ops = pci_dma_ops; -#ifdef CONFIG_NUMA - sd->numa_node = pcibus_to_node(dev->bus); -#else - sd->numa_node = -1; -#endif + set_dev_node(&dev->dev, pcibus_to_node(dev->bus)); + if (ppc_md.pci_dma_dev_setup) ppc_md.pci_dma_dev_setup(dev); } diff --git a/arch/powerpc/kernel/vio.c b/arch/powerpc/kernel/vio.c index 2750fbab197..434c92a85c0 100644 --- a/arch/powerpc/kernel/vio.c +++ b/arch/powerpc/kernel/vio.c @@ -1232,7 +1232,7 @@ struct vio_dev *vio_register_device_node(struct device_node *of_node) else viodev->dev.archdata.dma_ops = &dma_iommu_ops; viodev->dev.archdata.dma_data = vio_build_iommu_table(viodev); - viodev->dev.archdata.numa_node = of_node_to_nid(of_node); + set_dev_node(&viodev->dev, of_node_to_nid(of_node)); /* init generic 'struct device' fields: */ viodev->dev.parent = &vio_bus_device.dev; diff --git a/arch/powerpc/platforms/cell/iommu.c b/arch/powerpc/platforms/cell/iommu.c index e06420af5fe..ef92e714621 100644 --- a/arch/powerpc/platforms/cell/iommu.c +++ b/arch/powerpc/platforms/cell/iommu.c @@ -556,11 +556,11 @@ static struct iommu_table *cell_get_iommu_table(struct device *dev) * node's iommu. We -might- do something smarter later though it may * never be necessary */ - iommu = cell_iommu_for_node(archdata->numa_node); + iommu = cell_iommu_for_node(dev_to_node(dev)); if (iommu == NULL || list_empty(&iommu->windows)) { printk(KERN_ERR "iommu: missing iommu for %s (node %d)\n", archdata->of_node ? archdata->of_node->full_name : "?", - archdata->numa_node); + dev_to_node(dev)); return NULL; } window = list_entry(iommu->windows.next, struct iommu_window, list); @@ -577,7 +577,7 @@ static void *dma_fixed_alloc_coherent(struct device *dev, size_t size, return iommu_alloc_coherent(dev, cell_get_iommu_table(dev), size, dma_handle, device_to_mask(dev), flag, - dev->archdata.numa_node); + dev_to_node(dev)); else return dma_direct_ops.alloc_coherent(dev, size, dma_handle, flag); diff --git a/arch/powerpc/platforms/ps3/system-bus.c b/arch/powerpc/platforms/ps3/system-bus.c index 280ee88cb0b..a789bf58ca8 100644 --- a/arch/powerpc/platforms/ps3/system-bus.c +++ b/arch/powerpc/platforms/ps3/system-bus.c @@ -762,7 +762,7 @@ int ps3_system_bus_device_register(struct ps3_system_bus_device *dev) }; dev->core.archdata.of_node = NULL; - dev->core.archdata.numa_node = 0; + set_dev_node(&dev->core, 0); pr_debug("%s:%d add %s\n", __func__, __LINE__, dev->core.bus_id); -- cgit v1.2.3 From 4fc665b88a79a45bae8bbf3a05563c27c7337c3d Mon Sep 17 00:00:00 2001 From: Becky Bruce Date: Fri, 12 Sep 2008 10:34:46 +0000 Subject: powerpc: Merge 32 and 64-bit dma code We essentially adopt the 64-bit dma code, with some changes to support 32-bit systems, including HIGHMEM. dma functions on 32-bit are now invoked via accessor functions which call the correct op for a device based on archdata dma_ops. If there is no archdata dma_ops, this defaults to dma_direct_ops. In addition, the dma_map/unmap_page functions are added to dma_ops because we can't just fall back on map/unmap_single when HIGHMEM is enabled. In the case of dma_direct_*, we stop using map/unmap_single and just use the page version - this saves a lot of ugly ifdeffing. We leave map/unmap_single in the dma_ops definition, though, because they are needed by the iommu code, which does not implement map/unmap_page. Ideally, going forward, we will completely eliminate map/unmap_single and just have map/unmap_page, if it's workable for 64-bit. Signed-off-by: Becky Bruce Signed-off-by: Kumar Gala --- arch/powerpc/include/asm/dma-mapping.h | 187 +++++++++++---------------------- arch/powerpc/include/asm/machdep.h | 5 +- arch/powerpc/include/asm/pci.h | 14 +-- arch/powerpc/kernel/Makefile | 4 +- arch/powerpc/kernel/dma.c | 69 ++++++++---- arch/powerpc/kernel/pci-common.c | 48 +++++++++ arch/powerpc/kernel/pci_32.c | 7 ++ arch/powerpc/kernel/pci_64.c | 46 -------- 8 files changed, 175 insertions(+), 205 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/dma-mapping.h b/arch/powerpc/include/asm/dma-mapping.h index c7ca45f97dd..fddb229bd74 100644 --- a/arch/powerpc/include/asm/dma-mapping.h +++ b/arch/powerpc/include/asm/dma-mapping.h @@ -44,8 +44,6 @@ extern void __dma_sync_page(struct page *page, unsigned long offset, #endif /* ! CONFIG_NOT_COHERENT_CACHE */ -#ifdef CONFIG_PPC64 - static inline unsigned long device_to_mask(struct device *dev) { if (dev->dma_mask && *dev->dma_mask) @@ -76,8 +74,24 @@ struct dma_mapping_ops { struct dma_attrs *attrs); int (*dma_supported)(struct device *dev, u64 mask); int (*set_dma_mask)(struct device *dev, u64 dma_mask); + dma_addr_t (*map_page)(struct device *dev, struct page *page, + unsigned long offset, size_t size, + enum dma_data_direction direction, + struct dma_attrs *attrs); + void (*unmap_page)(struct device *dev, + dma_addr_t dma_address, size_t size, + enum dma_data_direction direction, + struct dma_attrs *attrs); }; +/* + * Available generic sets of operations + */ +#ifdef CONFIG_PPC64 +extern struct dma_mapping_ops dma_iommu_ops; +#endif +extern struct dma_mapping_ops dma_direct_ops; + static inline struct dma_mapping_ops *get_dma_ops(struct device *dev) { /* We don't handle the NULL dev case for ISA for now. We could @@ -85,8 +99,19 @@ static inline struct dma_mapping_ops *get_dma_ops(struct device *dev) * only ISA DMA device we support is the floppy and we have a hack * in the floppy driver directly to get a device for us. */ - if (unlikely(dev == NULL || dev->archdata.dma_ops == NULL)) + + if (unlikely(dev == NULL) || dev->archdata.dma_ops == NULL) { +#ifdef CONFIG_PPC64 return NULL; +#else + /* Use default on 32-bit if dma_ops is not set up */ + /* TODO: Long term, we should fix drivers so that dev and + * archdata dma_ops are set up for all buses. + */ + return &dma_direct_ops; +#endif + } + return dev->archdata.dma_ops; } @@ -123,6 +148,12 @@ static inline int dma_set_mask(struct device *dev, u64 dma_mask) return 0; } +/* + * TODO: map_/unmap_single will ideally go away, to be completely + * replaced by map/unmap_page. Until then, we allow dma_ops to have + * one or the other, or both by checking to see if the specific + * function requested exists; and if not, falling back on the other set. + */ static inline dma_addr_t dma_map_single_attrs(struct device *dev, void *cpu_addr, size_t size, @@ -132,7 +163,14 @@ static inline dma_addr_t dma_map_single_attrs(struct device *dev, struct dma_mapping_ops *dma_ops = get_dma_ops(dev); BUG_ON(!dma_ops); - return dma_ops->map_single(dev, cpu_addr, size, direction, attrs); + + if (dma_ops->map_single) + return dma_ops->map_single(dev, cpu_addr, size, direction, + attrs); + + return dma_ops->map_page(dev, virt_to_page(cpu_addr), + (unsigned long)cpu_addr % PAGE_SIZE, size, + direction, attrs); } static inline void dma_unmap_single_attrs(struct device *dev, @@ -144,7 +182,13 @@ static inline void dma_unmap_single_attrs(struct device *dev, struct dma_mapping_ops *dma_ops = get_dma_ops(dev); BUG_ON(!dma_ops); - dma_ops->unmap_single(dev, dma_addr, size, direction, attrs); + + if (dma_ops->unmap_single) { + dma_ops->unmap_single(dev, dma_addr, size, direction, attrs); + return; + } + + dma_ops->unmap_page(dev, dma_addr, size, direction, attrs); } static inline dma_addr_t dma_map_page_attrs(struct device *dev, @@ -156,8 +200,13 @@ static inline dma_addr_t dma_map_page_attrs(struct device *dev, struct dma_mapping_ops *dma_ops = get_dma_ops(dev); BUG_ON(!dma_ops); + + if (dma_ops->map_page) + return dma_ops->map_page(dev, page, offset, size, direction, + attrs); + return dma_ops->map_single(dev, page_address(page) + offset, size, - direction, attrs); + direction, attrs); } static inline void dma_unmap_page_attrs(struct device *dev, @@ -169,6 +218,12 @@ static inline void dma_unmap_page_attrs(struct device *dev, struct dma_mapping_ops *dma_ops = get_dma_ops(dev); BUG_ON(!dma_ops); + + if (dma_ops->unmap_page) { + dma_ops->unmap_page(dev, dma_address, size, direction, attrs); + return; + } + dma_ops->unmap_single(dev, dma_address, size, direction, attrs); } @@ -253,126 +308,6 @@ static inline void dma_unmap_sg(struct device *dev, struct scatterlist *sg, dma_unmap_sg_attrs(dev, sg, nhwentries, direction, NULL); } -/* - * Available generic sets of operations - */ -extern struct dma_mapping_ops dma_iommu_ops; -extern struct dma_mapping_ops dma_direct_ops; - -#else /* CONFIG_PPC64 */ - -#define dma_supported(dev, mask) (1) - -static inline int dma_set_mask(struct device *dev, u64 dma_mask) -{ - if (!dev->dma_mask || !dma_supported(dev, mask)) - return -EIO; - - *dev->dma_mask = dma_mask; - - return 0; -} - -static inline void *dma_alloc_coherent(struct device *dev, size_t size, - dma_addr_t * dma_handle, - gfp_t gfp) -{ -#ifdef CONFIG_NOT_COHERENT_CACHE - return __dma_alloc_coherent(size, dma_handle, gfp); -#else - void *ret; - /* ignore region specifiers */ - gfp &= ~(__GFP_DMA | __GFP_HIGHMEM); - - if (dev == NULL || dev->coherent_dma_mask < 0xffffffff) - gfp |= GFP_DMA; - - ret = (void *)__get_free_pages(gfp, get_order(size)); - - if (ret != NULL) { - memset(ret, 0, size); - *dma_handle = virt_to_bus(ret); - } - - return ret; -#endif -} - -static inline void -dma_free_coherent(struct device *dev, size_t size, void *vaddr, - dma_addr_t dma_handle) -{ -#ifdef CONFIG_NOT_COHERENT_CACHE - __dma_free_coherent(size, vaddr); -#else - free_pages((unsigned long)vaddr, get_order(size)); -#endif -} - -static inline dma_addr_t -dma_map_single(struct device *dev, void *ptr, size_t size, - enum dma_data_direction direction) -{ - BUG_ON(direction == DMA_NONE); - - __dma_sync(ptr, size, direction); - - return virt_to_bus(ptr); -} - -static inline void dma_unmap_single(struct device *dev, dma_addr_t dma_addr, - size_t size, - enum dma_data_direction direction) -{ - /* We do nothing. */ -} - -static inline dma_addr_t -dma_map_page(struct device *dev, struct page *page, - unsigned long offset, size_t size, - enum dma_data_direction direction) -{ - BUG_ON(direction == DMA_NONE); - - __dma_sync_page(page, offset, size, direction); - - return page_to_bus(page) + offset; -} - -static inline void dma_unmap_page(struct device *dev, dma_addr_t dma_address, - size_t size, - enum dma_data_direction direction) -{ - /* We do nothing. */ -} - -static inline int -dma_map_sg(struct device *dev, struct scatterlist *sgl, int nents, - enum dma_data_direction direction) -{ - struct scatterlist *sg; - int i; - - BUG_ON(direction == DMA_NONE); - - for_each_sg(sgl, sg, nents, i) { - BUG_ON(!sg_page(sg)); - __dma_sync_page(sg_page(sg), sg->offset, sg->length, direction); - sg->dma_address = page_to_bus(sg_page(sg)) + sg->offset; - } - - return nents; -} - -static inline void dma_unmap_sg(struct device *dev, struct scatterlist *sg, - int nhwentries, - enum dma_data_direction direction) -{ - /* We don't do anything here. */ -} - -#endif /* CONFIG_PPC64 */ - static inline void dma_sync_single_for_cpu(struct device *dev, dma_addr_t dma_handle, size_t size, enum dma_data_direction direction) diff --git a/arch/powerpc/include/asm/machdep.h b/arch/powerpc/include/asm/machdep.h index 893aafd87fd..2740c44ff71 100644 --- a/arch/powerpc/include/asm/machdep.h +++ b/arch/powerpc/include/asm/machdep.h @@ -88,8 +88,6 @@ struct machdep_calls { unsigned long (*tce_get)(struct iommu_table *tbl, long index); void (*tce_flush)(struct iommu_table *tbl); - void (*pci_dma_dev_setup)(struct pci_dev *dev); - void (*pci_dma_bus_setup)(struct pci_bus *bus); void __iomem * (*ioremap)(phys_addr_t addr, unsigned long size, unsigned long flags); @@ -101,6 +99,9 @@ struct machdep_calls { #endif #endif /* CONFIG_PPC64 */ + void (*pci_dma_dev_setup)(struct pci_dev *dev); + void (*pci_dma_bus_setup)(struct pci_bus *bus); + int (*probe)(void); void (*setup_arch)(void); /* Optional, may be NULL */ void (*init_early)(void); diff --git a/arch/powerpc/include/asm/pci.h b/arch/powerpc/include/asm/pci.h index a05a942b1c2..0e52c7828ea 100644 --- a/arch/powerpc/include/asm/pci.h +++ b/arch/powerpc/include/asm/pci.h @@ -60,6 +60,14 @@ static inline int pci_get_legacy_ide_irq(struct pci_dev *dev, int channel) return channel ? 15 : 14; } +#ifdef CONFIG_PCI +extern void set_pci_dma_ops(struct dma_mapping_ops *dma_ops); +extern struct dma_mapping_ops *get_pci_dma_ops(void); +#else /* CONFIG_PCI */ +#define set_pci_dma_ops(d) +#define get_pci_dma_ops() NULL +#endif + #ifdef CONFIG_PPC64 /* @@ -70,9 +78,6 @@ static inline int pci_get_legacy_ide_irq(struct pci_dev *dev, int channel) #define PCI_DISABLE_MWI #ifdef CONFIG_PCI -extern void set_pci_dma_ops(struct dma_mapping_ops *dma_ops); -extern struct dma_mapping_ops *get_pci_dma_ops(void); - static inline void pci_dma_burst_advice(struct pci_dev *pdev, enum pci_dma_burst_strategy *strat, unsigned long *strategy_parameter) @@ -89,9 +94,6 @@ static inline void pci_dma_burst_advice(struct pci_dev *pdev, *strat = PCI_DMA_BURST_MULTIPLE; *strategy_parameter = cacheline_size; } -#else /* CONFIG_PCI */ -#define set_pci_dma_ops(d) -#define get_pci_dma_ops() NULL #endif #else /* 32-bit */ diff --git a/arch/powerpc/kernel/Makefile b/arch/powerpc/kernel/Makefile index 09b3cabf2f9..fdb58253fa5 100644 --- a/arch/powerpc/kernel/Makefile +++ b/arch/powerpc/kernel/Makefile @@ -70,10 +70,10 @@ extra-$(CONFIG_8xx) := head_8xx.o extra-y += vmlinux.lds obj-y += time.o prom.o traps.o setup-common.o \ - udbg.o misc.o io.o \ + udbg.o misc.o io.o dma.o \ misc_$(CONFIG_WORD_SIZE).o obj-$(CONFIG_PPC32) += entry_32.o setup_32.o -obj-$(CONFIG_PPC64) += dma.o dma-iommu.o iommu.o +obj-$(CONFIG_PPC64) += dma-iommu.o iommu.o obj-$(CONFIG_KGDB) += kgdb.o obj-$(CONFIG_PPC_MULTIPLATFORM) += prom_init.o obj-$(CONFIG_MODULES) += ppc_ksyms.o diff --git a/arch/powerpc/kernel/dma.c b/arch/powerpc/kernel/dma.c index 124f86743bd..41fdd48bf43 100644 --- a/arch/powerpc/kernel/dma.c +++ b/arch/powerpc/kernel/dma.c @@ -16,21 +16,30 @@ * This implementation supports a per-device offset that can be applied if * the address at which memory is visible to devices is not 0. Platform code * can set archdata.dma_data to an unsigned long holding the offset. By - * default the offset is zero. + * default the offset is PCI_DRAM_OFFSET. */ static unsigned long get_dma_direct_offset(struct device *dev) { - return (unsigned long)dev->archdata.dma_data; + if (dev) + return (unsigned long)dev->archdata.dma_data; + + return PCI_DRAM_OFFSET; } -static void *dma_direct_alloc_coherent(struct device *dev, size_t size, - dma_addr_t *dma_handle, gfp_t flag) +void *dma_direct_alloc_coherent(struct device *dev, size_t size, + dma_addr_t *dma_handle, gfp_t flag) { +#ifdef CONFIG_NOT_COHERENT_CACHE + return __dma_alloc_coherent(size, dma_handle, flag); +#else struct page *page; void *ret; int node = dev_to_node(dev); + /* ignore region specifiers */ + flag &= ~(__GFP_HIGHMEM); + page = alloc_pages_node(node, flag, get_order(size)); if (page == NULL) return NULL; @@ -39,27 +48,17 @@ static void *dma_direct_alloc_coherent(struct device *dev, size_t size, *dma_handle = virt_to_abs(ret) + get_dma_direct_offset(dev); return ret; +#endif } -static void dma_direct_free_coherent(struct device *dev, size_t size, - void *vaddr, dma_addr_t dma_handle) +void dma_direct_free_coherent(struct device *dev, size_t size, + void *vaddr, dma_addr_t dma_handle) { +#ifdef CONFIG_NOT_COHERENT_CACHE + __dma_free_coherent(size, vaddr); +#else free_pages((unsigned long)vaddr, get_order(size)); -} - -static dma_addr_t dma_direct_map_single(struct device *dev, void *ptr, - size_t size, - enum dma_data_direction direction, - struct dma_attrs *attrs) -{ - return virt_to_abs(ptr) + get_dma_direct_offset(dev); -} - -static void dma_direct_unmap_single(struct device *dev, dma_addr_t dma_addr, - size_t size, - enum dma_data_direction direction, - struct dma_attrs *attrs) -{ +#endif } static int dma_direct_map_sg(struct device *dev, struct scatterlist *sgl, @@ -85,20 +84,44 @@ static void dma_direct_unmap_sg(struct device *dev, struct scatterlist *sg, static int dma_direct_dma_supported(struct device *dev, u64 mask) { +#ifdef CONFIG_PPC64 /* Could be improved to check for memory though it better be * done via some global so platforms can set the limit in case * they have limited DMA windows */ return mask >= DMA_32BIT_MASK; +#else + return 1; +#endif +} + +static inline dma_addr_t dma_direct_map_page(struct device *dev, + struct page *page, + unsigned long offset, + size_t size, + enum dma_data_direction dir, + struct dma_attrs *attrs) +{ + BUG_ON(dir == DMA_NONE); + __dma_sync_page(page, offset, size, dir); + return page_to_phys(page) + offset + get_dma_direct_offset(dev); +} + +static inline void dma_direct_unmap_page(struct device *dev, + dma_addr_t dma_address, + size_t size, + enum dma_data_direction direction, + struct dma_attrs *attrs) +{ } struct dma_mapping_ops dma_direct_ops = { .alloc_coherent = dma_direct_alloc_coherent, .free_coherent = dma_direct_free_coherent, - .map_single = dma_direct_map_single, - .unmap_single = dma_direct_unmap_single, .map_sg = dma_direct_map_sg, .unmap_sg = dma_direct_unmap_sg, .dma_supported = dma_direct_dma_supported, + .map_page = dma_direct_map_page, + .unmap_page = dma_direct_unmap_page, }; EXPORT_SYMBOL(dma_direct_ops); diff --git a/arch/powerpc/kernel/pci-common.c b/arch/powerpc/kernel/pci-common.c index ea0c61e09b7..52ccfed416a 100644 --- a/arch/powerpc/kernel/pci-common.c +++ b/arch/powerpc/kernel/pci-common.c @@ -56,6 +56,34 @@ resource_size_t isa_mem_base; /* Default PCI flags is 0 */ unsigned int ppc_pci_flags; +static struct dma_mapping_ops *pci_dma_ops; + +void set_pci_dma_ops(struct dma_mapping_ops *dma_ops) +{ + pci_dma_ops = dma_ops; +} + +struct dma_mapping_ops *get_pci_dma_ops(void) +{ + return pci_dma_ops; +} +EXPORT_SYMBOL(get_pci_dma_ops); + +int pci_set_dma_mask(struct pci_dev *dev, u64 mask) +{ + return dma_set_mask(&dev->dev, mask); +} + +int pci_set_consistent_dma_mask(struct pci_dev *dev, u64 mask) +{ + int rc; + + rc = dma_set_mask(&dev->dev, mask); + dev->dev.coherent_dma_mask = dev->dma_mask; + + return rc; +} + struct pci_controller *pcibios_alloc_controller(struct device_node *dev) { struct pci_controller *phb; @@ -180,6 +208,26 @@ char __devinit *pcibios_setup(char *str) return str; } +void __devinit pcibios_setup_new_device(struct pci_dev *dev) +{ + struct dev_archdata *sd = &dev->dev.archdata; + + sd->of_node = pci_device_to_OF_node(dev); + + DBG("PCI: device %s OF node: %s\n", pci_name(dev), + sd->of_node ? sd->of_node->full_name : ""); + + sd->dma_ops = pci_dma_ops; +#ifdef CONFIG_PPC32 + sd->dma_data = (void *)PCI_DRAM_OFFSET; +#endif + set_dev_node(&dev->dev, pcibus_to_node(dev->bus)); + + if (ppc_md.pci_dma_dev_setup) + ppc_md.pci_dma_dev_setup(dev); +} +EXPORT_SYMBOL(pcibios_setup_new_device); + /* * Reads the interrupt pin to determine if interrupt is use by card. * If the interrupt is used, then gets the interrupt line from the diff --git a/arch/powerpc/kernel/pci_32.c b/arch/powerpc/kernel/pci_32.c index 88db4ffaf11..174b77ee18f 100644 --- a/arch/powerpc/kernel/pci_32.c +++ b/arch/powerpc/kernel/pci_32.c @@ -424,6 +424,7 @@ void __devinit pcibios_do_bus_setup(struct pci_bus *bus) unsigned long io_offset; struct resource *res; int i; + struct pci_dev *dev; /* Hookup PHB resources */ io_offset = (unsigned long)hose->io_base_virt - isa_io_base; @@ -457,6 +458,12 @@ void __devinit pcibios_do_bus_setup(struct pci_bus *bus) bus->resource[i+1] = res; } } + + if (ppc_md.pci_dma_bus_setup) + ppc_md.pci_dma_bus_setup(bus); + + list_for_each_entry(dev, &bus->devices, bus_list) + pcibios_setup_new_device(dev); } /* the next one is stolen from the alpha port... */ diff --git a/arch/powerpc/kernel/pci_64.c b/arch/powerpc/kernel/pci_64.c index 1f75bf03446..8247cff1cb3 100644 --- a/arch/powerpc/kernel/pci_64.c +++ b/arch/powerpc/kernel/pci_64.c @@ -52,35 +52,6 @@ EXPORT_SYMBOL(pci_io_base); LIST_HEAD(hose_list); -static struct dma_mapping_ops *pci_dma_ops; - -void set_pci_dma_ops(struct dma_mapping_ops *dma_ops) -{ - pci_dma_ops = dma_ops; -} - -struct dma_mapping_ops *get_pci_dma_ops(void) -{ - return pci_dma_ops; -} -EXPORT_SYMBOL(get_pci_dma_ops); - - -int pci_set_dma_mask(struct pci_dev *dev, u64 mask) -{ - return dma_set_mask(&dev->dev, mask); -} - -int pci_set_consistent_dma_mask(struct pci_dev *dev, u64 mask) -{ - int rc; - - rc = dma_set_mask(&dev->dev, mask); - dev->dev.coherent_dma_mask = dev->dma_mask; - - return rc; -} - static void fixup_broken_pcnet32(struct pci_dev* dev) { if ((dev->class>>8 == PCI_CLASS_NETWORK_ETHERNET)) { @@ -548,23 +519,6 @@ int __devinit pcibios_map_io_space(struct pci_bus *bus) } EXPORT_SYMBOL_GPL(pcibios_map_io_space); -void __devinit pcibios_setup_new_device(struct pci_dev *dev) -{ - struct dev_archdata *sd = &dev->dev.archdata; - - sd->of_node = pci_device_to_OF_node(dev); - - DBG("PCI: device %s OF node: %s\n", pci_name(dev), - sd->of_node ? sd->of_node->full_name : ""); - - sd->dma_ops = pci_dma_ops; - set_dev_node(&dev->dev, pcibus_to_node(dev->bus)); - - if (ppc_md.pci_dma_dev_setup) - ppc_md.pci_dma_dev_setup(dev); -} -EXPORT_SYMBOL(pcibios_setup_new_device); - void __devinit pcibios_do_bus_setup(struct pci_bus *bus) { struct pci_dev *dev; -- cgit v1.2.3 From b9579689ad3a208c342aed806afc7a9a808c4e1e Mon Sep 17 00:00:00 2001 From: Becky Bruce Date: Fri, 12 Sep 2008 10:53:43 +0000 Subject: powerpc: Make dma_addr_t a u64 if CONFIG_PHYS_64BIT is set Signed-off-by: Becky Bruce Signed-off-by: Kumar Gala --- arch/powerpc/include/asm/types.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/types.h b/arch/powerpc/include/asm/types.h index d3374bc865b..a9a9262e84a 100644 --- a/arch/powerpc/include/asm/types.h +++ b/arch/powerpc/include/asm/types.h @@ -55,7 +55,7 @@ typedef u64 phys_addr_t; typedef u32 phys_addr_t; #endif -#ifdef __powerpc64__ +#if defined(__powerpc64__) || defined(CONFIG_PHYS_64BIT) typedef u64 dma_addr_t; #else typedef u32 dma_addr_t; -- cgit v1.2.3 From 0ba3418b8b1c85ee1771c63f1dd12041614e56ff Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 15 Jul 2008 16:12:25 -0500 Subject: powerpc: Introduce local (non-broadcast) forms of tlb invalidates Introduced a new set of low level tlb invalidate functions that do not broadcast invalidates on the bus: _tlbil_all - invalidate all _tlbil_pid - invalidate based on process id (or mm context) _tlbil_va - invalidate based on virtual address (ea + pid) On non-SMP configs _tlbil_all should be functionally equivalent to _tlbia and _tlbil_va should be functionally equivalent to _tlbie. The intent of this change is to handle SMP based invalidates via IPIs instead of broadcasts as the mechanism scales better for larger number of cores. On e500 (fsl-booke mmu) based cores move to using MMUCSR for invalidate alls and tlbsx/tlbwe for invalidate virtual address. Signed-off-by: Kumar Gala --- arch/powerpc/include/asm/reg_booke.h | 7 +++++ arch/powerpc/include/asm/tlbflush.h | 13 +++++---- arch/powerpc/kernel/misc_32.S | 54 ++++++++++++++++++++++++++++++++++++ arch/powerpc/kernel/ppc_ksyms.c | 3 ++ 4 files changed, 72 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/reg_booke.h b/arch/powerpc/include/asm/reg_booke.h index be980f4ee49..67453766bff 100644 --- a/arch/powerpc/include/asm/reg_booke.h +++ b/arch/powerpc/include/asm/reg_booke.h @@ -109,6 +109,7 @@ #define SPRN_EVPR 0x3D6 /* Exception Vector Prefix Register */ #define SPRN_L1CSR0 0x3F2 /* L1 Cache Control and Status Register 0 */ #define SPRN_L1CSR1 0x3F3 /* L1 Cache Control and Status Register 1 */ +#define SPRN_MMUCSR0 0x3F4 /* MMU Control and Status Register 0 */ #define SPRN_PIT 0x3DB /* Programmable Interval Timer */ #define SPRN_BUCSR 0x3F5 /* Branch Unit Control and Status */ #define SPRN_L2CSR0 0x3F9 /* L2 Data Cache Control and Status Register 0 */ @@ -410,6 +411,12 @@ #define L2CSR0_L2LOA 0x00000080 /* L2 Cache Lock Overflow Allocate */ #define L2CSR0_L2LO 0x00000020 /* L2 Cache Lock Overflow */ +/* Bit definitions for MMUCSR0 */ +#define MMUCSR0_TLB1FI 0x00000002 /* TLB1 Flash invalidate */ +#define MMUCSR0_TLB0FI 0x00000004 /* TLB0 Flash invalidate */ +#define MMUCSR0_TLB2FI 0x00000040 /* TLB2 Flash invalidate */ +#define MMUCSR0_TLB3FI 0x00000020 /* TLB3 Flash invalidate */ + /* Bit definitions for SGR. */ #define SGR_NORMAL 0 /* Speculative fetching allowed. */ #define SGR_GUARDED 1 /* Speculative fetching disallowed. */ diff --git a/arch/powerpc/include/asm/tlbflush.h b/arch/powerpc/include/asm/tlbflush.h index 361cd5c7a32..a2c6bfd85fb 100644 --- a/arch/powerpc/include/asm/tlbflush.h +++ b/arch/powerpc/include/asm/tlbflush.h @@ -29,6 +29,9 @@ #include extern void _tlbie(unsigned long address, unsigned int pid); +extern void _tlbil_all(void); +extern void _tlbil_pid(unsigned int pid); +extern void _tlbil_va(unsigned long address, unsigned int pid); #if defined(CONFIG_40x) || defined(CONFIG_8xx) #define _tlbia() asm volatile ("tlbia; sync" : : : "memory") @@ -38,31 +41,31 @@ extern void _tlbia(void); static inline void flush_tlb_mm(struct mm_struct *mm) { - _tlbia(); + _tlbil_pid(mm->context.id); } static inline void flush_tlb_page(struct vm_area_struct *vma, unsigned long vmaddr) { - _tlbie(vmaddr, vma ? vma->vm_mm->context.id : 0); + _tlbil_va(vmaddr, vma ? vma->vm_mm->context.id : 0); } static inline void flush_tlb_page_nohash(struct vm_area_struct *vma, unsigned long vmaddr) { - _tlbie(vmaddr, vma ? vma->vm_mm->context.id : 0); + flush_tlb_page(vma, vmaddr); } static inline void flush_tlb_range(struct vm_area_struct *vma, unsigned long start, unsigned long end) { - _tlbia(); + _tlbil_pid(vma->vm_mm->context.id); } static inline void flush_tlb_kernel_range(unsigned long start, unsigned long end) { - _tlbia(); + _tlbil_pid(0); } #elif defined(CONFIG_PPC32) diff --git a/arch/powerpc/kernel/misc_32.S b/arch/powerpc/kernel/misc_32.S index 7a6dfbca768..e9c8ab6eabf 100644 --- a/arch/powerpc/kernel/misc_32.S +++ b/arch/powerpc/kernel/misc_32.S @@ -274,6 +274,10 @@ _GLOBAL(real_writeb) /* * Flush MMU TLB */ +#ifndef CONFIG_FSL_BOOKE +_GLOBAL(_tlbil_all) +_GLOBAL(_tlbil_pid) +#endif _GLOBAL(_tlbia) #if defined(CONFIG_40x) sync /* Flush to memory before changing mapping */ @@ -344,6 +348,9 @@ _GLOBAL(_tlbia) /* * Flush MMU TLB for a particular address */ +#ifndef CONFIG_FSL_BOOKE +_GLOBAL(_tlbil_va) +#endif _GLOBAL(_tlbie) #if defined(CONFIG_40x) /* We run the search with interrupts disabled because we have to change @@ -436,6 +443,53 @@ _GLOBAL(_tlbie) #endif /* ! CONFIG_40x */ blr +#if defined(CONFIG_FSL_BOOKE) +/* + * Flush MMU TLB, but only on the local processor (no broadcast) + */ +_GLOBAL(_tlbil_all) +#define MMUCSR0_TLBFI (MMUCSR0_TLB0FI | MMUCSR0_TLB1FI | \ + MMUCSR0_TLB2FI | MMUCSR0_TLB3FI) + li r3,(MMUCSR0_TLBFI)@l + mtspr SPRN_MMUCSR0, r3 +1: + mfspr r3,SPRN_MMUCSR0 + andi. r3,r3,MMUCSR0_TLBFI@l + bne 1b + blr + +/* + * Flush MMU TLB for a particular process id, but only on the local processor + * (no broadcast) + */ +_GLOBAL(_tlbil_pid) +/* we currently do an invalidate all since we don't have per pid invalidate */ + li r3,(MMUCSR0_TLBFI)@l + mtspr SPRN_MMUCSR0, r3 +1: + mfspr r3,SPRN_MMUCSR0 + andi. r3,r3,MMUCSR0_TLBFI@l + bne 1b + blr + +/* + * Flush MMU TLB for a particular address, but only on the local processor + * (no broadcast) + */ +_GLOBAL(_tlbil_va) + slwi r4,r4,16 + mtspr SPRN_MAS6,r4 /* assume AS=0 for now */ + tlbsx 0,r3 + mfspr r4,SPRN_MAS1 /* check valid */ + andis. r3,r4,MAS1_VALID@h + beqlr + rlwinm r4,r4,0,1,31 + mtspr SPRN_MAS1,r4 + tlbwe + blr +#endif /* CONFIG_FSL_BOOKE */ + + /* * Flush instruction cache. * This is a no-op on the 601. diff --git a/arch/powerpc/kernel/ppc_ksyms.c b/arch/powerpc/kernel/ppc_ksyms.c index e1ea4fe5cfb..8edc2359c41 100644 --- a/arch/powerpc/kernel/ppc_ksyms.c +++ b/arch/powerpc/kernel/ppc_ksyms.c @@ -119,6 +119,9 @@ EXPORT_SYMBOL(flush_instruction_cache); EXPORT_SYMBOL(flush_tlb_kernel_range); EXPORT_SYMBOL(flush_tlb_page); EXPORT_SYMBOL(_tlbie); +#if defined(CONFIG_4xx) || defined(CONFIG_8xx) || defined(CONFIG_FSL_BOOKE) +EXPORT_SYMBOL(_tlbil_va); +#endif #endif EXPORT_SYMBOL(__flush_icache_range); EXPORT_SYMBOL(flush_dcache_range); -- cgit v1.2.3 From 9bf2b5cdc5fe5e3136ceeecc85141765023ded6e Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Wed, 16 Jul 2008 15:54:21 -0500 Subject: powerpc: Fixes for CONFIG_PTE_64BIT for SMP support There are some minor issues with support 64-bit PTEs on a 32-bit processor when dealing with SMP. * We need to order the stores in set_pte_at to make sure the flag word is set second. * Change pte_clear to use pte_update so only the flag word is cleared * Added a WARN_ON to set_pte_at to ensure the pte isn't present for the 64-bit pte/SMP case (to ensure our assumption of this fact). Signed-off-by: Kumar Gala Acked-by: Becky Bruce --- arch/powerpc/include/asm/highmem.h | 2 +- arch/powerpc/include/asm/pgtable-ppc32.h | 25 ++++++++++++++++++++----- 2 files changed, 21 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/highmem.h b/arch/powerpc/include/asm/highmem.h index 5d99b6489d5..91c589520c0 100644 --- a/arch/powerpc/include/asm/highmem.h +++ b/arch/powerpc/include/asm/highmem.h @@ -84,7 +84,7 @@ static inline void *kmap_atomic_prot(struct page *page, enum km_type type, pgpro #ifdef CONFIG_DEBUG_HIGHMEM BUG_ON(!pte_none(*(kmap_pte-idx))); #endif - set_pte_at(&init_mm, vaddr, kmap_pte-idx, mk_pte(page, prot)); + __set_pte_at(&init_mm, vaddr, kmap_pte-idx, mk_pte(page, prot)); flush_tlb_page(NULL, vaddr); return (void*) vaddr; diff --git a/arch/powerpc/include/asm/pgtable-ppc32.h b/arch/powerpc/include/asm/pgtable-ppc32.h index 6fe39e32704..1b119555547 100644 --- a/arch/powerpc/include/asm/pgtable-ppc32.h +++ b/arch/powerpc/include/asm/pgtable-ppc32.h @@ -517,7 +517,8 @@ extern unsigned long bad_call_to_PMD_PAGE_SIZE(void); #define pte_none(pte) ((pte_val(pte) & ~_PTE_NONE_MASK) == 0) #define pte_present(pte) (pte_val(pte) & _PAGE_PRESENT) -#define pte_clear(mm,addr,ptep) do { set_pte_at((mm), (addr), (ptep), __pte(0)); } while (0) +#define pte_clear(mm, addr, ptep) \ + do { pte_update(ptep, ~_PAGE_HASHPTE, 0); } while (0) #define pmd_none(pmd) (!pmd_val(pmd)) #define pmd_bad(pmd) (pmd_val(pmd) & _PMD_BAD) @@ -612,9 +613,6 @@ static inline unsigned long pte_update(pte_t *p, return old; } #else /* CONFIG_PTE_64BIT */ -/* TODO: Change that to only modify the low word and move set_pte_at() - * out of line - */ static inline unsigned long long pte_update(pte_t *p, unsigned long clr, unsigned long set) @@ -652,16 +650,33 @@ static inline unsigned long long pte_update(pte_t *p, * On machines which use an MMU hash table we avoid changing the * _PAGE_HASHPTE bit. */ -static inline void set_pte_at(struct mm_struct *mm, unsigned long addr, + +static inline void __set_pte_at(struct mm_struct *mm, unsigned long addr, pte_t *ptep, pte_t pte) { #if _PAGE_HASHPTE != 0 pte_update(ptep, ~_PAGE_HASHPTE, pte_val(pte) & ~_PAGE_HASHPTE); +#elif defined(CONFIG_PTE_64BIT) && defined(CONFIG_SMP) + __asm__ __volatile__("\ + stw%U0%X0 %2,%0\n\ + eieio\n\ + stw%U0%X0 %L2,%1" + : "=m" (*ptep), "=m" (*((unsigned char *)ptep+4)) + : "r" (pte) : "memory"); #else *ptep = pte; #endif } +static inline void set_pte_at(struct mm_struct *mm, unsigned long addr, + pte_t *ptep, pte_t pte) +{ +#if defined(CONFIG_PTE_64BIT) && defined(CONFIG_SMP) + WARN_ON(pte_present(*ptep)); +#endif + __set_pte_at(mm, addr, ptep, pte); +} + /* * 2.6 calls this without flushing the TLB entry; this is wrong * for our hash-based implementation, we fix that up here. -- cgit v1.2.3 From 9a62c05180ff55fdaa517370c6f077402820406c Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Thu, 31 Jul 2008 08:41:10 -0500 Subject: powerpc/mm: Implement _PAGE_SPECIAL & pte_special() for 32-bit Implement _PAGE_SPECIAL and pte_special() for 32-bit powerpc. This bit will be used by the fast get_user_pages() to differenciate PTEs that correspond to a valid struct page from special mappings that don't such as IO mappings obtained via io_remap_pfn_ranges(). We currently only implement this on sub-arch that support SMP or will so in the future (6xx, 44x, FSL-BookE) and not (8xx, 40x). Signed-off-by: Kumar Gala Acked-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/pgtable-ppc32.h | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/pgtable-ppc32.h b/arch/powerpc/include/asm/pgtable-ppc32.h index 1b119555547..c2e58b41bc7 100644 --- a/arch/powerpc/include/asm/pgtable-ppc32.h +++ b/arch/powerpc/include/asm/pgtable-ppc32.h @@ -261,6 +261,7 @@ extern int icache_44x_need_flush; #define _PAGE_HWEXEC 0x00000004 /* H: Execute permission */ #define _PAGE_ACCESSED 0x00000008 /* S: Page referenced */ #define _PAGE_DIRTY 0x00000010 /* S: Page dirty */ +#define _PAGE_SPECIAL 0x00000020 /* S: Special page */ #define _PAGE_USER 0x00000040 /* S: User page */ #define _PAGE_ENDIAN 0x00000080 /* H: E bit */ #define _PAGE_GUARDED 0x00000100 /* H: G bit */ @@ -276,6 +277,7 @@ extern int icache_44x_need_flush; /* ERPN in a PTE never gets cleared, ignore it */ #define _PTE_NONE_MASK 0xffffffff00000000ULL +#define __HAVE_ARCH_PTE_SPECIAL #elif defined(CONFIG_FSL_BOOKE) /* @@ -305,6 +307,7 @@ extern int icache_44x_need_flush; #define _PAGE_COHERENT 0x00100 /* H: M bit */ #define _PAGE_NO_CACHE 0x00200 /* H: I bit */ #define _PAGE_WRITETHRU 0x00400 /* H: W bit */ +#define _PAGE_SPECIAL 0x00800 /* S: Special page */ #ifdef CONFIG_PTE_64BIT /* ERPN in a PTE never gets cleared, ignore it */ @@ -315,6 +318,8 @@ extern int icache_44x_need_flush; #define _PMD_PRESENT_MASK (PAGE_MASK) #define _PMD_BAD (~PAGE_MASK) +#define __HAVE_ARCH_PTE_SPECIAL + #elif defined(CONFIG_8xx) /* Definitions for 8xx embedded chips. */ #define _PAGE_PRESENT 0x0001 /* Page is valid */ @@ -362,6 +367,7 @@ extern int icache_44x_need_flush; #define _PAGE_ACCESSED 0x100 /* R: page referenced */ #define _PAGE_EXEC 0x200 /* software: i-cache coherency required */ #define _PAGE_RW 0x400 /* software: user write access allowed */ +#define _PAGE_SPECIAL 0x800 /* software: Special page */ #define _PTE_NONE_MASK _PAGE_HASHPTE @@ -372,6 +378,8 @@ extern int icache_44x_need_flush; /* Hash table based platforms need atomic updates of the linux PTE */ #define PTE_ATOMIC_UPDATES 1 +#define __HAVE_ARCH_PTE_SPECIAL + #endif /* @@ -404,6 +412,9 @@ extern int icache_44x_need_flush; #ifndef _PAGE_WRITETHRU #define _PAGE_WRITETHRU 0 #endif +#ifndef _PAGE_SPECIAL +#define _PAGE_SPECIAL 0 +#endif #ifndef _PMD_PRESENT_MASK #define _PMD_PRESENT_MASK _PMD_PRESENT #endif @@ -534,7 +545,7 @@ static inline int pte_write(pte_t pte) { return pte_val(pte) & _PAGE_RW; } static inline int pte_dirty(pte_t pte) { return pte_val(pte) & _PAGE_DIRTY; } static inline int pte_young(pte_t pte) { return pte_val(pte) & _PAGE_ACCESSED; } static inline int pte_file(pte_t pte) { return pte_val(pte) & _PAGE_FILE; } -static inline int pte_special(pte_t pte) { return 0; } +static inline int pte_special(pte_t pte) { return pte_val(pte) & _PAGE_SPECIAL; } static inline void pte_uncache(pte_t pte) { pte_val(pte) |= _PAGE_NO_CACHE; } static inline void pte_cache(pte_t pte) { pte_val(pte) &= ~_PAGE_NO_CACHE; } @@ -553,7 +564,7 @@ static inline pte_t pte_mkdirty(pte_t pte) { static inline pte_t pte_mkyoung(pte_t pte) { pte_val(pte) |= _PAGE_ACCESSED; return pte; } static inline pte_t pte_mkspecial(pte_t pte) { - return pte; } + pte_val(pte) |= _PAGE_SPECIAL; return pte; } static inline unsigned long pte_pgprot(pte_t pte) { return __pgprot(pte_val(pte)) & PAGE_PROT_BITS; -- cgit v1.2.3 From 4ee7084eb11e00eb02dc8435fd18273a61ffa9bf Mon Sep 17 00:00:00 2001 From: Becky Bruce Date: Wed, 24 Sep 2008 11:01:24 -0500 Subject: POWERPC: Allow 32-bit hashed pgtable code to support 36-bit physical This rearranges a bit of code, and adds support for 36-bit physical addressing for configs that use a hashed page table. The 36b physical support is not enabled by default on any config - it must be explicitly enabled via the config system. This patch *only* expands the page table code to accomodate large physical addresses on 32-bit systems and enables the PHYS_64BIT config option for 86xx. It does *not* allow you to boot a board with more than about 3.5GB of RAM - for that, SWIOTLB support is also required (and coming soon). Signed-off-by: Becky Bruce Signed-off-by: Kumar Gala --- arch/powerpc/include/asm/io.h | 2 +- arch/powerpc/include/asm/page_32.h | 8 ++- arch/powerpc/include/asm/pgtable-ppc32.h | 17 ++++++- arch/powerpc/kernel/asm-offsets.c | 1 + arch/powerpc/kernel/head_32.S | 4 +- arch/powerpc/kernel/head_fsl_booke.S | 2 - arch/powerpc/mm/hash_low_32.S | 86 ++++++++++++++++++++++++++------ arch/powerpc/mm/pgtable_32.c | 4 +- arch/powerpc/mm/tlb_32.c | 1 + arch/powerpc/platforms/Kconfig.cputype | 17 ++++--- 10 files changed, 109 insertions(+), 33 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/io.h b/arch/powerpc/include/asm/io.h index 77c7fa025e6..08266d2728b 100644 --- a/arch/powerpc/include/asm/io.h +++ b/arch/powerpc/include/asm/io.h @@ -711,7 +711,7 @@ static inline void * phys_to_virt(unsigned long address) /* * Change "struct page" to physical address. */ -#define page_to_phys(page) (page_to_pfn(page) << PAGE_SHIFT) +#define page_to_phys(page) ((phys_addr_t)page_to_pfn(page) << PAGE_SHIFT) /* We do NOT want virtual merging, it would put too much pressure on * our iommu allocator. Instead, we want drivers to be smart enough diff --git a/arch/powerpc/include/asm/page_32.h b/arch/powerpc/include/asm/page_32.h index ebfae530a37..d77072a32cc 100644 --- a/arch/powerpc/include/asm/page_32.h +++ b/arch/powerpc/include/asm/page_32.h @@ -13,10 +13,16 @@ #define ARCH_KMALLOC_MINALIGN L1_CACHE_BYTES #endif +#ifdef CONFIG_PTE_64BIT +#define PTE_FLAGS_OFFSET 4 /* offset of PTE flags, in bytes */ +#else +#define PTE_FLAGS_OFFSET 0 +#endif + #ifndef __ASSEMBLY__ /* * The basic type of a PTE - 64 bits for those CPUs with > 32 bit - * physical addressing. For now this just the IBM PPC440. + * physical addressing. */ #ifdef CONFIG_PTE_64BIT typedef unsigned long long pte_basic_t; diff --git a/arch/powerpc/include/asm/pgtable-ppc32.h b/arch/powerpc/include/asm/pgtable-ppc32.h index c2e58b41bc7..29c83d85b04 100644 --- a/arch/powerpc/include/asm/pgtable-ppc32.h +++ b/arch/powerpc/include/asm/pgtable-ppc32.h @@ -369,7 +369,12 @@ extern int icache_44x_need_flush; #define _PAGE_RW 0x400 /* software: user write access allowed */ #define _PAGE_SPECIAL 0x800 /* software: Special page */ +#ifdef CONFIG_PTE_64BIT +/* We never clear the high word of the pte */ +#define _PTE_NONE_MASK (0xffffffff00000000ULL | _PAGE_HASHPTE) +#else #define _PTE_NONE_MASK _PAGE_HASHPTE +#endif #define _PMD_PRESENT 0 #define _PMD_PRESENT_MASK (PAGE_MASK) @@ -587,6 +592,10 @@ extern int flush_hash_pages(unsigned context, unsigned long va, extern void add_hash_page(unsigned context, unsigned long va, unsigned long pmdval); +/* Flush an entry from the TLB/hash table */ +extern void flush_hash_entry(struct mm_struct *mm, pte_t *ptep, + unsigned long address); + /* * Atomic PTE updates. * @@ -665,9 +674,13 @@ static inline unsigned long long pte_update(pte_t *p, static inline void __set_pte_at(struct mm_struct *mm, unsigned long addr, pte_t *ptep, pte_t pte) { -#if _PAGE_HASHPTE != 0 +#if (_PAGE_HASHPTE != 0) && defined(CONFIG_SMP) && !defined(CONFIG_PTE_64BIT) pte_update(ptep, ~_PAGE_HASHPTE, pte_val(pte) & ~_PAGE_HASHPTE); #elif defined(CONFIG_PTE_64BIT) && defined(CONFIG_SMP) +#if _PAGE_HASHPTE != 0 + if (pte_val(*ptep) & _PAGE_HASHPTE) + flush_hash_entry(mm, ptep, addr); +#endif __asm__ __volatile__("\ stw%U0%X0 %2,%0\n\ eieio\n\ @@ -675,7 +688,7 @@ static inline void __set_pte_at(struct mm_struct *mm, unsigned long addr, : "=m" (*ptep), "=m" (*((unsigned char *)ptep+4)) : "r" (pte) : "memory"); #else - *ptep = pte; + *ptep = (*ptep & _PAGE_HASHPTE) | (pte & ~_PAGE_HASHPTE); #endif } diff --git a/arch/powerpc/kernel/asm-offsets.c b/arch/powerpc/kernel/asm-offsets.c index e9c4044012b..09febc58258 100644 --- a/arch/powerpc/kernel/asm-offsets.c +++ b/arch/powerpc/kernel/asm-offsets.c @@ -352,6 +352,7 @@ int main(void) #endif DEFINE(PGD_TABLE_SIZE, PGD_TABLE_SIZE); + DEFINE(PTE_SIZE, sizeof(pte_t)); #ifdef CONFIG_KVM DEFINE(TLBE_BYTES, sizeof(struct tlbe)); diff --git a/arch/powerpc/kernel/head_32.S b/arch/powerpc/kernel/head_32.S index 8bb65751929..a6de6dbc5ed 100644 --- a/arch/powerpc/kernel/head_32.S +++ b/arch/powerpc/kernel/head_32.S @@ -369,13 +369,13 @@ i##n: \ DataAccess: EXCEPTION_PROLOG mfspr r10,SPRN_DSISR + stw r10,_DSISR(r11) andis. r0,r10,0xa470 /* weird error? */ bne 1f /* if not, try to put a PTE */ mfspr r4,SPRN_DAR /* into the hash table */ rlwinm r3,r10,32-15,21,21 /* DSISR_STORE -> _PAGE_RW */ bl hash_page -1: stw r10,_DSISR(r11) - mr r5,r10 +1: lwz r5,_DSISR(r11) /* get DSISR value */ mfspr r4,SPRN_DAR EXC_XFER_EE_LITE(0x300, handle_page_fault) diff --git a/arch/powerpc/kernel/head_fsl_booke.S b/arch/powerpc/kernel/head_fsl_booke.S index 377e0c155c9..18c0093f932 100644 --- a/arch/powerpc/kernel/head_fsl_booke.S +++ b/arch/powerpc/kernel/head_fsl_booke.S @@ -422,7 +422,6 @@ skpinv: addi r6,r6,1 /* Increment */ * r12 is pointer to the pte */ #ifdef CONFIG_PTE_64BIT -#define PTE_FLAGS_OFFSET 4 #define FIND_PTE \ rlwinm r12, r10, 13, 19, 29; /* Compute pgdir/pmd offset */ \ lwzx r11, r12, r11; /* Get pgd/pmd entry */ \ @@ -431,7 +430,6 @@ skpinv: addi r6,r6,1 /* Increment */ rlwimi r12, r10, 23, 20, 28; /* Compute pte address */ \ lwz r11, 4(r12); /* Get pte entry */ #else -#define PTE_FLAGS_OFFSET 0 #define FIND_PTE \ rlwimi r11, r10, 12, 20, 29; /* Create L1 (pgdir/pmd) address */ \ lwz r11, 0(r11); /* Get L1 entry */ \ diff --git a/arch/powerpc/mm/hash_low_32.S b/arch/powerpc/mm/hash_low_32.S index c41d658176a..7bffb70b9fe 100644 --- a/arch/powerpc/mm/hash_low_32.S +++ b/arch/powerpc/mm/hash_low_32.S @@ -75,7 +75,7 @@ _GLOBAL(hash_page_sync) * Returns to the caller if the access is illegal or there is no * mapping for the address. Otherwise it places an appropriate PTE * in the hash table and returns from the exception. - * Uses r0, r3 - r8, ctr, lr. + * Uses r0, r3 - r8, r10, ctr, lr. */ .text _GLOBAL(hash_page) @@ -106,9 +106,15 @@ _GLOBAL(hash_page) addi r5,r5,swapper_pg_dir@l /* kernel page table */ rlwimi r3,r9,32-12,29,29 /* MSR_PR -> _PAGE_USER */ 112: add r5,r5,r7 /* convert to phys addr */ +#ifndef CONFIG_PTE_64BIT rlwimi r5,r4,12,20,29 /* insert top 10 bits of address */ lwz r8,0(r5) /* get pmd entry */ rlwinm. r8,r8,0,0,19 /* extract address of pte page */ +#else + rlwinm r8,r4,13,19,29 /* Compute pgdir/pmd offset */ + lwzx r8,r8,r5 /* Get L1 entry */ + rlwinm. r8,r8,0,0,20 /* extract pt base address */ +#endif #ifdef CONFIG_SMP beq- hash_page_out /* return if no mapping */ #else @@ -118,7 +124,11 @@ _GLOBAL(hash_page) to the address following the rfi. */ beqlr- #endif +#ifndef CONFIG_PTE_64BIT rlwimi r8,r4,22,20,29 /* insert next 10 bits of address */ +#else + rlwimi r8,r4,23,20,28 /* compute pte address */ +#endif rlwinm r0,r3,32-3,24,24 /* _PAGE_RW access -> _PAGE_DIRTY */ ori r0,r0,_PAGE_ACCESSED|_PAGE_HASHPTE @@ -127,9 +137,15 @@ _GLOBAL(hash_page) * because almost always, there won't be a permission violation * and there won't already be an HPTE, and thus we will have * to update the PTE to set _PAGE_HASHPTE. -- paulus. + * + * If PTE_64BIT is set, the low word is the flags word; use that + * word for locking since it contains all the interesting bits. */ +#if (PTE_FLAGS_OFFSET != 0) + addi r8,r8,PTE_FLAGS_OFFSET +#endif retry: - lwarx r6,0,r8 /* get linux-style pte */ + lwarx r6,0,r8 /* get linux-style pte, flag word */ andc. r5,r3,r6 /* check access & ~permission */ #ifdef CONFIG_SMP bne- hash_page_out /* return if access not permitted */ @@ -137,6 +153,15 @@ retry: bnelr- #endif or r5,r0,r6 /* set accessed/dirty bits */ +#ifdef CONFIG_PTE_64BIT +#ifdef CONFIG_SMP + subf r10,r6,r8 /* create false data dependency */ + subi r10,r10,PTE_FLAGS_OFFSET + lwzx r10,r6,r10 /* Get upper PTE word */ +#else + lwz r10,-PTE_FLAGS_OFFSET(r8) +#endif /* CONFIG_SMP */ +#endif /* CONFIG_PTE_64BIT */ stwcx. r5,0,r8 /* attempt to update PTE */ bne- retry /* retry if someone got there first */ @@ -203,9 +228,9 @@ _GLOBAL(add_hash_page) * we can't take a hash table miss (assuming the code is * covered by a BAT). -- paulus */ - mfmsr r10 + mfmsr r9 SYNC - rlwinm r0,r10,0,17,15 /* clear bit 16 (MSR_EE) */ + rlwinm r0,r9,0,17,15 /* clear bit 16 (MSR_EE) */ rlwinm r0,r0,0,28,26 /* clear MSR_DR */ mtmsr r0 SYNC_601 @@ -214,14 +239,14 @@ _GLOBAL(add_hash_page) tophys(r7,0) #ifdef CONFIG_SMP - addis r9,r7,mmu_hash_lock@ha - addi r9,r9,mmu_hash_lock@l -10: lwarx r0,0,r9 /* take the mmu_hash_lock */ + addis r6,r7,mmu_hash_lock@ha + addi r6,r6,mmu_hash_lock@l +10: lwarx r0,0,r6 /* take the mmu_hash_lock */ cmpi 0,r0,0 bne- 11f - stwcx. r8,0,r9 + stwcx. r8,0,r6 beq+ 12f -11: lwz r0,0(r9) +11: lwz r0,0(r6) cmpi 0,r0,0 beq 10b b 11b @@ -234,10 +259,24 @@ _GLOBAL(add_hash_page) * HPTE, so we just unlock and return. */ mr r8,r5 +#ifndef CONFIG_PTE_64BIT rlwimi r8,r4,22,20,29 +#else + rlwimi r8,r4,23,20,28 + addi r8,r8,PTE_FLAGS_OFFSET +#endif 1: lwarx r6,0,r8 andi. r0,r6,_PAGE_HASHPTE bne 9f /* if HASHPTE already set, done */ +#ifdef CONFIG_PTE_64BIT +#ifdef CONFIG_SMP + subf r10,r6,r8 /* create false data dependency */ + subi r10,r10,PTE_FLAGS_OFFSET + lwzx r10,r6,r10 /* Get upper PTE word */ +#else + lwz r10,-PTE_FLAGS_OFFSET(r8) +#endif /* CONFIG_SMP */ +#endif /* CONFIG_PTE_64BIT */ ori r5,r6,_PAGE_HASHPTE stwcx. r5,0,r8 bne- 1b @@ -246,13 +285,15 @@ _GLOBAL(add_hash_page) 9: #ifdef CONFIG_SMP + addis r6,r7,mmu_hash_lock@ha + addi r6,r6,mmu_hash_lock@l eieio li r0,0 - stw r0,0(r9) /* clear mmu_hash_lock */ + stw r0,0(r6) /* clear mmu_hash_lock */ #endif /* reenable interrupts and DR */ - mtmsr r10 + mtmsr r9 SYNC_601 isync @@ -267,7 +308,8 @@ _GLOBAL(add_hash_page) * r5 contains the linux PTE, r6 contains the old value of the * linux PTE (before setting _PAGE_HASHPTE) and r7 contains the * offset to be added to addresses (0 if the MMU is on, - * -KERNELBASE if it is off). + * -KERNELBASE if it is off). r10 contains the upper half of + * the PTE if CONFIG_PTE_64BIT. * On SMP, the caller should have the mmu_hash_lock held. * We assume that the caller has (or will) set the _PAGE_HASHPTE * bit in the linux PTE in memory. The value passed in r6 should @@ -313,6 +355,11 @@ _GLOBAL(create_hpte) BEGIN_FTR_SECTION ori r8,r8,_PAGE_COHERENT /* set M (coherence required) */ END_FTR_SECTION_IFSET(CPU_FTR_NEED_COHERENT) +#ifdef CONFIG_PTE_64BIT + /* Put the XPN bits into the PTE */ + rlwimi r8,r10,8,20,22 + rlwimi r8,r10,2,29,29 +#endif /* Construct the high word of the PPC-style PTE (r5) */ rlwinm r5,r3,7,1,24 /* put VSID in 0x7fffff80 bits */ @@ -499,14 +546,18 @@ _GLOBAL(flush_hash_pages) isync /* First find a PTE in the range that has _PAGE_HASHPTE set */ +#ifndef CONFIG_PTE_64BIT rlwimi r5,r4,22,20,29 -1: lwz r0,0(r5) +#else + rlwimi r5,r4,23,20,28 +#endif +1: lwz r0,PTE_FLAGS_OFFSET(r5) cmpwi cr1,r6,1 andi. r0,r0,_PAGE_HASHPTE bne 2f ble cr1,19f addi r4,r4,0x1000 - addi r5,r5,4 + addi r5,r5,PTE_SIZE addi r6,r6,-1 b 1b @@ -545,7 +596,10 @@ _GLOBAL(flush_hash_pages) * already clear, we're done (for this pte). If not, * clear it (atomically) and proceed. -- paulus. */ -33: lwarx r8,0,r5 /* fetch the pte */ +#if (PTE_FLAGS_OFFSET != 0) + addi r5,r5,PTE_FLAGS_OFFSET +#endif +33: lwarx r8,0,r5 /* fetch the pte flags word */ andi. r0,r8,_PAGE_HASHPTE beq 8f /* done if HASHPTE is already clear */ rlwinm r8,r8,0,31,29 /* clear HASHPTE bit */ @@ -590,7 +644,7 @@ _GLOBAL(flush_hash_patch_B) 8: ble cr1,9f /* if all ptes checked */ 81: addi r6,r6,-1 - addi r5,r5,4 /* advance to next pte */ + addi r5,r5,PTE_SIZE addi r4,r4,0x1000 lwz r0,0(r5) /* check next pte */ cmpwi cr1,r6,1 diff --git a/arch/powerpc/mm/pgtable_32.c b/arch/powerpc/mm/pgtable_32.c index 2001abdb191..c31d6d26f0b 100644 --- a/arch/powerpc/mm/pgtable_32.c +++ b/arch/powerpc/mm/pgtable_32.c @@ -73,7 +73,7 @@ extern unsigned long p_mapped_by_tlbcam(unsigned long pa); #endif /* HAVE_TLBCAM */ #ifdef CONFIG_PTE_64BIT -/* 44x uses an 8kB pgdir because it has 8-byte Linux PTEs. */ +/* Some processors use an 8kB pgdir because they have 8-byte Linux PTEs. */ #define PGDIR_ORDER 1 #else #define PGDIR_ORDER 0 @@ -288,7 +288,7 @@ int map_page(unsigned long va, phys_addr_t pa, int flags) } /* - * Map in all of physical memory starting at KERNELBASE. + * Map in a big chunk of physical memory starting at KERNELBASE. */ void __init mapin_ram(void) { diff --git a/arch/powerpc/mm/tlb_32.c b/arch/powerpc/mm/tlb_32.c index eb4b512d65f..f9a47fee392 100644 --- a/arch/powerpc/mm/tlb_32.c +++ b/arch/powerpc/mm/tlb_32.c @@ -45,6 +45,7 @@ void flush_hash_entry(struct mm_struct *mm, pte_t *ptep, unsigned long addr) flush_hash_pages(mm->context.id, addr, ptephys, 1); } } +EXPORT_SYMBOL(flush_hash_entry); /* * Called by ptep_set_access_flags, must flush on CPUs for which the diff --git a/arch/powerpc/platforms/Kconfig.cputype b/arch/powerpc/platforms/Kconfig.cputype index 7f651273386..439c5ba34ec 100644 --- a/arch/powerpc/platforms/Kconfig.cputype +++ b/arch/powerpc/platforms/Kconfig.cputype @@ -50,6 +50,7 @@ config 44x select PPC_UDBG_16550 select 4xx_SOC select PPC_PCI_CHOICE + select PHYS_64BIT config E200 bool "Freescale e200" @@ -128,18 +129,20 @@ config FSL_EMB_PERFMON config PTE_64BIT bool - depends on 44x || E500 - default y if 44x - default y if E500 && PHYS_64BIT + depends on 44x || E500 || PPC_86xx + default y if PHYS_64BIT config PHYS_64BIT - bool 'Large physical address support' if E500 - depends on 44x || E500 + bool 'Large physical address support' if E500 || PPC_86xx + depends on (44x || E500 || PPC_86xx) && !PPC_83xx && !PPC_82xx select RESOURCES_64BIT - default y if 44x ---help--- This option enables kernel support for larger than 32-bit physical - addresses. This features is not be available on all e500 cores. + addresses. This feature may not be available on all cores. + + If you have more than 3.5GB of RAM or so, you also need to enable + SWIOTLB under Kernel Options for this to work. The actual number + is platform-dependent. If in doubt, say N here. -- cgit v1.2.3 From 20d38e01d48019c578ab0ec1464454c03003b300 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Mon, 29 Sep 2008 17:56:03 +0400 Subject: powerpc/fsl_soc: remove mpc83xx_wdt code mpc83xx_wdt is the OF driver now, so we don't need fsl_soc constructor. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/sysdev/fsl_soc.c | 47 ------------------------------------------- 1 file changed, 47 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c index 214388e1180..eeb07007c75 100644 --- a/arch/powerpc/sysdev/fsl_soc.c +++ b/arch/powerpc/sysdev/fsl_soc.c @@ -412,53 +412,6 @@ err: arch_initcall(gfar_of_init); - -#ifdef CONFIG_PPC_83xx -static int __init mpc83xx_wdt_init(void) -{ - struct resource r; - struct device_node *np; - struct platform_device *dev; - u32 freq = fsl_get_sys_freq(); - int ret; - - np = of_find_compatible_node(NULL, "watchdog", "mpc83xx_wdt"); - - if (!np) { - ret = -ENODEV; - goto nodev; - } - - memset(&r, 0, sizeof(r)); - - ret = of_address_to_resource(np, 0, &r); - if (ret) - goto err; - - dev = platform_device_register_simple("mpc83xx_wdt", 0, &r, 1); - if (IS_ERR(dev)) { - ret = PTR_ERR(dev); - goto err; - } - - ret = platform_device_add_data(dev, &freq, sizeof(freq)); - if (ret) - goto unreg; - - of_node_put(np); - return 0; - -unreg: - platform_device_unregister(dev); -err: - of_node_put(np); -nodev: - return ret; -} - -arch_initcall(mpc83xx_wdt_init); -#endif - static enum fsl_usb2_phy_modes determine_usb_phy(const char *phy_type) { if (!phy_type) -- cgit v1.2.3 From 0161dca52d950676d727336cef1441ea2bcfba98 Mon Sep 17 00:00:00 2001 From: Becky Bruce Date: Wed, 24 Sep 2008 16:53:34 -0500 Subject: powerpc: Drop redundant machine type print in show_cpuinfo For many of the embedded boards, "model" and "Machine" are printing the same thing; remove the redundant code and allow the generic show_cpuinfo to print the model information. Signed-off-by: Becky Bruce Acked-by: Paul Gortmaker Acked-by: Martyn Welch Signed-off-by: Kumar Gala --- arch/powerpc/platforms/85xx/mpc85xx_ads.c | 1 - arch/powerpc/platforms/85xx/sbc8560.c | 1 - arch/powerpc/platforms/86xx/gef_sbc610.c | 8 -------- arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 8 -------- arch/powerpc/platforms/86xx/sbc8641d.c | 8 -------- arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c | 1 - 6 files changed, 27 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ads.c b/arch/powerpc/platforms/85xx/mpc85xx_ads.c index d17807a6b89..0293e3d3580 100644 --- a/arch/powerpc/platforms/85xx/mpc85xx_ads.c +++ b/arch/powerpc/platforms/85xx/mpc85xx_ads.c @@ -213,7 +213,6 @@ static void mpc85xx_ads_show_cpuinfo(struct seq_file *m) svid = mfspr(SPRN_SVR); seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n"); - seq_printf(m, "Machine\t\t: mpc85xx\n"); seq_printf(m, "PVR\t\t: 0x%x\n", pvid); seq_printf(m, "SVR\t\t: 0x%x\n", svid); diff --git a/arch/powerpc/platforms/85xx/sbc8560.c b/arch/powerpc/platforms/85xx/sbc8560.c index e0cf0602d8b..0c9a856f66b 100644 --- a/arch/powerpc/platforms/85xx/sbc8560.c +++ b/arch/powerpc/platforms/85xx/sbc8560.c @@ -200,7 +200,6 @@ static void sbc8560_show_cpuinfo(struct seq_file *m) svid = mfspr(SPRN_SVR); seq_printf(m, "Vendor\t\t: Wind River\n"); - seq_printf(m, "Machine\t\t: SBC8560\n"); seq_printf(m, "PVR\t\t: 0x%x\n", pvid); seq_printf(m, "SVR\t\t: 0x%x\n", svid); diff --git a/arch/powerpc/platforms/86xx/gef_sbc610.c b/arch/powerpc/platforms/86xx/gef_sbc610.c index 3543a9e6761..8a9dee24761 100644 --- a/arch/powerpc/platforms/86xx/gef_sbc610.c +++ b/arch/powerpc/platforms/86xx/gef_sbc610.c @@ -66,19 +66,11 @@ static void __init gef_sbc610_setup_arch(void) static void gef_sbc610_show_cpuinfo(struct seq_file *m) { - struct device_node *root; uint memsize = total_memory; - const char *model = ""; uint svid = mfspr(SPRN_SVR); seq_printf(m, "Vendor\t\t: GE Fanuc Intelligent Platforms\n"); - root = of_find_node_by_path("/"); - if (root) - model = of_get_property(root, "model", NULL); - seq_printf(m, "Machine\t\t: %s\n", model); - of_node_put(root); - seq_printf(m, "SVR\t\t: 0x%x\n", svid); seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024)); } diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c index f712d9c0991..2672829a71d 100644 --- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c +++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c @@ -101,19 +101,11 @@ mpc86xx_hpcn_setup_arch(void) static void mpc86xx_hpcn_show_cpuinfo(struct seq_file *m) { - struct device_node *root; uint memsize = total_memory; - const char *model = ""; uint svid = mfspr(SPRN_SVR); seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n"); - root = of_find_node_by_path("/"); - if (root) - model = of_get_property(root, "model", NULL); - seq_printf(m, "Machine\t\t: %s\n", model); - of_node_put(root); - seq_printf(m, "SVR\t\t: 0x%x\n", svid); seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024)); } diff --git a/arch/powerpc/platforms/86xx/sbc8641d.c b/arch/powerpc/platforms/86xx/sbc8641d.c index 00e6fad3b3c..da677a74e2d 100644 --- a/arch/powerpc/platforms/86xx/sbc8641d.c +++ b/arch/powerpc/platforms/86xx/sbc8641d.c @@ -63,19 +63,11 @@ sbc8641_setup_arch(void) static void sbc8641_show_cpuinfo(struct seq_file *m) { - struct device_node *root; uint memsize = total_memory; - const char *model = ""; uint svid = mfspr(SPRN_SVR); seq_printf(m, "Vendor\t\t: Wind River Systems\n"); - root = of_find_node_by_path("/"); - if (root) - model = of_get_property(root, "model", NULL); - seq_printf(m, "Machine\t\t: %s\n", model); - of_node_put(root); - seq_printf(m, "SVR\t\t: 0x%x\n", svid); seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024)); } diff --git a/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c index 84e2d78b9a6..7a2ba39d781 100644 --- a/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c +++ b/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c @@ -164,7 +164,6 @@ static void __init mpc7448_hpc2_init_IRQ(void) void mpc7448_hpc2_show_cpuinfo(struct seq_file *m) { seq_printf(m, "vendor\t\t: Freescale Semiconductor\n"); - seq_printf(m, "machine\t\t: MPC7448hpc2\n"); } void mpc7448_hpc2_restart(char *cmd) -- cgit v1.2.3 From a969e76a7101bf5f3d369563df1ca1253dd6131b Mon Sep 17 00:00:00 2001 From: Martyn Welch Date: Mon, 29 Sep 2008 13:35:15 +0100 Subject: powerpc: Correct USB support for GE Fanuc SBC610 Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D). Fixup to correctly reconfigure USB, provided by an NEC uPD720101, after device is reset. This requires a set of chip specific registers in the devices configuration space to be correctly written, enabling all ports and switching the device to use an external 48-MHz Oscillator. Signed-off-by: Martyn Welch Signed-off-by: Kumar Gala --- arch/powerpc/platforms/86xx/gef_sbc610.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/platforms/86xx/gef_sbc610.c b/arch/powerpc/platforms/86xx/gef_sbc610.c index 8a9dee24761..ee215002b1c 100644 --- a/arch/powerpc/platforms/86xx/gef_sbc610.c +++ b/arch/powerpc/platforms/86xx/gef_sbc610.c @@ -12,6 +12,8 @@ * * Based on: mpc86xx_hpcn.c (MPC86xx HPCN board specific routines) * Copyright 2006 Freescale Semiconductor Inc. + * + * NEC fixup adapted from arch/mips/pci/fixup-lm2e.c */ #include @@ -75,6 +77,21 @@ static void gef_sbc610_show_cpuinfo(struct seq_file *m) seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024)); } +static void __init gef_sbc610_nec_fixup(struct pci_dev *pdev) +{ + unsigned int val; + + printk(KERN_INFO "Running NEC uPD720101 Fixup\n"); + + /* Ensure ports 1, 2, 3, 4 & 5 are enabled */ + pci_read_config_dword(pdev, 0xe0, &val); + pci_write_config_dword(pdev, 0xe0, (val & ~7) | 0x5); + + /* System clock is 48-MHz Oscillator and EHCI Enabled. */ + pci_write_config_dword(pdev, 0xe4, 1 << 5); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_USB, + gef_sbc610_nec_fixup); /* * Called very early, device-tree isn't unflattened -- cgit v1.2.3 From fbcc4bacee30cad4e4a13d05492a9ed0c9c3e8c7 Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Thu, 4 Sep 2008 04:08:20 +0000 Subject: ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer Acked-by: Benjamin Herrenschmidt Acked-by: Jeff Garzik Signed-off-by: Josh Boyer --- arch/powerpc/include/asm/dcr-regs.h | 7 +++++ drivers/net/ibm_newemac/mal.c | 60 +++++++++++++++++++++++++++++++++---- 2 files changed, 62 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/dcr-regs.h b/arch/powerpc/include/asm/dcr-regs.h index 29b0ecef980..7b833ff9c14 100644 --- a/arch/powerpc/include/asm/dcr-regs.h +++ b/arch/powerpc/include/asm/dcr-regs.h @@ -68,6 +68,13 @@ #define SDR0_UART3 0x0123 #define SDR0_CUST0 0x4000 +/* SDR for 405EZ */ +#define DCRN_SDR_ICINTSTAT 0x4510 +#define ICINTSTAT_ICRX 0x80000000 +#define ICINTSTAT_ICTX0 0x40000000 +#define ICINTSTAT_ICTX1 0x20000000 +#define ICINTSTAT_ICTX 0x60000000 + /* * All those DCR register addresses are offsets from the base address * for the SRAM0 controller (e.g. 0x20 on 440GX). The base address is diff --git a/drivers/net/ibm_newemac/mal.c b/drivers/net/ibm_newemac/mal.c index 10c267b2b96..1839d3f154a 100644 --- a/drivers/net/ibm_newemac/mal.c +++ b/drivers/net/ibm_newemac/mal.c @@ -28,6 +28,7 @@ #include #include "core.h" +#include static int mal_count; @@ -279,6 +280,10 @@ static irqreturn_t mal_txeob(int irq, void *dev_instance) mal_schedule_poll(mal); set_mal_dcrn(mal, MAL_TXEOBISR, r); + if (mal_has_feature(mal, MAL_FTR_CLEAR_ICINTSTAT)) + mtdcri(SDR0, DCRN_SDR_ICINTSTAT, + (mfdcri(SDR0, DCRN_SDR_ICINTSTAT) | ICINTSTAT_ICTX)); + return IRQ_HANDLED; } @@ -293,6 +298,10 @@ static irqreturn_t mal_rxeob(int irq, void *dev_instance) mal_schedule_poll(mal); set_mal_dcrn(mal, MAL_RXEOBISR, r); + if (mal_has_feature(mal, MAL_FTR_CLEAR_ICINTSTAT)) + mtdcri(SDR0, DCRN_SDR_ICINTSTAT, + (mfdcri(SDR0, DCRN_SDR_ICINTSTAT) | ICINTSTAT_ICRX)); + return IRQ_HANDLED; } @@ -336,6 +345,25 @@ static irqreturn_t mal_rxde(int irq, void *dev_instance) return IRQ_HANDLED; } +static irqreturn_t mal_int(int irq, void *dev_instance) +{ + struct mal_instance *mal = dev_instance; + u32 esr = get_mal_dcrn(mal, MAL_ESR); + + if (esr & MAL_ESR_EVB) { + /* descriptor error */ + if (esr & MAL_ESR_DE) { + if (esr & MAL_ESR_CIDT) + return mal_rxde(irq, dev_instance); + else + return mal_txde(irq, dev_instance); + } else { /* SERR */ + return mal_serr(irq, dev_instance); + } + } + return IRQ_HANDLED; +} + void mal_poll_disable(struct mal_instance *mal, struct mal_commac *commac) { /* Spinlock-type semantics: only one caller disable poll at a time */ @@ -493,6 +521,8 @@ static int __devinit mal_probe(struct of_device *ofdev, unsigned int dcr_base; const u32 *prop; u32 cfg; + unsigned long irqflags; + irq_handler_t hdlr_serr, hdlr_txde, hdlr_rxde; mal = kzalloc(sizeof(struct mal_instance), GFP_KERNEL); if (!mal) { @@ -542,11 +572,21 @@ static int __devinit mal_probe(struct of_device *ofdev, goto fail; } + if (of_device_is_compatible(ofdev->node, "ibm,mcmal-405ez")) + mal->features |= (MAL_FTR_CLEAR_ICINTSTAT | + MAL_FTR_COMMON_ERR_INT); + mal->txeob_irq = irq_of_parse_and_map(ofdev->node, 0); mal->rxeob_irq = irq_of_parse_and_map(ofdev->node, 1); mal->serr_irq = irq_of_parse_and_map(ofdev->node, 2); - mal->txde_irq = irq_of_parse_and_map(ofdev->node, 3); - mal->rxde_irq = irq_of_parse_and_map(ofdev->node, 4); + + if (mal_has_feature(mal, MAL_FTR_COMMON_ERR_INT)) { + mal->txde_irq = mal->rxde_irq = mal->serr_irq; + } else { + mal->txde_irq = irq_of_parse_and_map(ofdev->node, 3); + mal->rxde_irq = irq_of_parse_and_map(ofdev->node, 4); + } + if (mal->txeob_irq == NO_IRQ || mal->rxeob_irq == NO_IRQ || mal->serr_irq == NO_IRQ || mal->txde_irq == NO_IRQ || mal->rxde_irq == NO_IRQ) { @@ -608,16 +648,26 @@ static int __devinit mal_probe(struct of_device *ofdev, sizeof(struct mal_descriptor) * mal_rx_bd_offset(mal, i)); - err = request_irq(mal->serr_irq, mal_serr, 0, "MAL SERR", mal); + if (mal_has_feature(mal, MAL_FTR_COMMON_ERR_INT)) { + irqflags = IRQF_SHARED; + hdlr_serr = hdlr_txde = hdlr_rxde = mal_int; + } else { + irqflags = 0; + hdlr_serr = mal_serr; + hdlr_txde = mal_txde; + hdlr_rxde = mal_rxde; + } + + err = request_irq(mal->serr_irq, hdlr_serr, irqflags, "MAL SERR", mal); if (err) goto fail2; - err = request_irq(mal->txde_irq, mal_txde, 0, "MAL TX DE", mal); + err = request_irq(mal->txde_irq, hdlr_txde, irqflags, "MAL TX DE", mal); if (err) goto fail3; err = request_irq(mal->txeob_irq, mal_txeob, 0, "MAL TX EOB", mal); if (err) goto fail4; - err = request_irq(mal->rxde_irq, mal_rxde, 0, "MAL RX DE", mal); + err = request_irq(mal->rxde_irq, hdlr_rxde, irqflags, "MAL RX DE", mal); if (err) goto fail5; err = request_irq(mal->rxeob_irq, mal_rxeob, 0, "MAL RX EOB", mal); -- cgit v1.2.3 From d2b194ed820880eb19c43b9c10d9f5f30026ee54 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Wed, 4 Jun 2008 02:59:29 -0500 Subject: powerpc/math-emu: Use kernel generic math-emu code The math emulation code is centered around a set of generic macros that provide the core of the emulation that are shared by the various architectures and other projects (like glibc). Each arch implements its own sfp-machine.h to specific various arch specific details. For historic reasons that are now lost the powerpc math-emu code had its own version of the common headers. This moves us to using the kernel generic version and thus getting fixes when those are updated. Also cleaned up exception/error reporting from the FP emulation functions. Signed-off-by: Kumar Gala --- arch/powerpc/include/asm/sfp-machine.h | 353 +++++++++++++++++ arch/powerpc/math-emu/Makefile | 7 +- arch/powerpc/math-emu/double.h | 129 ------- arch/powerpc/math-emu/fadd.c | 17 +- arch/powerpc/math-emu/fadds.c | 20 +- arch/powerpc/math-emu/fcmpo.c | 10 +- arch/powerpc/math-emu/fcmpu.c | 10 +- arch/powerpc/math-emu/fctiw.c | 8 +- arch/powerpc/math-emu/fctiwz.c | 8 +- arch/powerpc/math-emu/fdiv.c | 14 +- arch/powerpc/math-emu/fdivs.c | 16 +- arch/powerpc/math-emu/fmadd.c | 16 +- arch/powerpc/math-emu/fmadds.c | 18 +- arch/powerpc/math-emu/fmsub.c | 16 +- arch/powerpc/math-emu/fmsubs.c | 18 +- arch/powerpc/math-emu/fmul.c | 14 +- arch/powerpc/math-emu/fmuls.c | 16 +- arch/powerpc/math-emu/fnmadd.c | 16 +- arch/powerpc/math-emu/fnmadds.c | 18 +- arch/powerpc/math-emu/fnmsub.c | 16 +- arch/powerpc/math-emu/fnmsubs.c | 18 +- arch/powerpc/math-emu/frsp.c | 14 +- arch/powerpc/math-emu/fsel.c | 8 +- arch/powerpc/math-emu/fsqrt.c | 12 +- arch/powerpc/math-emu/fsqrts.c | 14 +- arch/powerpc/math-emu/fsub.c | 14 +- arch/powerpc/math-emu/fsubs.c | 16 +- arch/powerpc/math-emu/lfd.c | 4 +- arch/powerpc/math-emu/lfs.c | 19 +- arch/powerpc/math-emu/math.c | 8 +- arch/powerpc/math-emu/mcrfs.c | 3 +- arch/powerpc/math-emu/mffs.c | 3 +- arch/powerpc/math-emu/mtfsb0.c | 3 +- arch/powerpc/math-emu/mtfsb1.c | 3 +- arch/powerpc/math-emu/mtfsf.c | 20 +- arch/powerpc/math-emu/mtfsfi.c | 3 +- arch/powerpc/math-emu/op-1.h | 245 ------------ arch/powerpc/math-emu/op-2.h | 434 --------------------- arch/powerpc/math-emu/op-4.h | 317 --------------- arch/powerpc/math-emu/op-common.h | 688 --------------------------------- arch/powerpc/math-emu/sfp-machine.h | 377 ------------------ arch/powerpc/math-emu/single.h | 66 ---- arch/powerpc/math-emu/soft-fp.h | 104 ----- arch/powerpc/math-emu/stfs.c | 19 +- arch/powerpc/math-emu/types.c | 51 --- arch/powerpc/math-emu/udivmodti4.c | 2 +- 46 files changed, 631 insertions(+), 2574 deletions(-) create mode 100644 arch/powerpc/include/asm/sfp-machine.h delete mode 100644 arch/powerpc/math-emu/double.h delete mode 100644 arch/powerpc/math-emu/op-1.h delete mode 100644 arch/powerpc/math-emu/op-2.h delete mode 100644 arch/powerpc/math-emu/op-4.h delete mode 100644 arch/powerpc/math-emu/op-common.h delete mode 100644 arch/powerpc/math-emu/sfp-machine.h delete mode 100644 arch/powerpc/math-emu/single.h delete mode 100644 arch/powerpc/math-emu/soft-fp.h delete mode 100644 arch/powerpc/math-emu/types.c (limited to 'arch') diff --git a/arch/powerpc/include/asm/sfp-machine.h b/arch/powerpc/include/asm/sfp-machine.h new file mode 100644 index 00000000000..ced34f1dc8f --- /dev/null +++ b/arch/powerpc/include/asm/sfp-machine.h @@ -0,0 +1,353 @@ +/* Machine-dependent software floating-point definitions. PPC version. + Copyright (C) 1997 Free Software Foundation, Inc. + This file is part of the GNU C Library. + + The GNU C Library is free software; you can redistribute it and/or + modify it under the terms of the GNU Library General Public License as + published by the Free Software Foundation; either version 2 of the + License, or (at your option) any later version. + + The GNU C Library is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + Library General Public License for more details. + + You should have received a copy of the GNU Library General Public + License along with the GNU C Library; see the file COPYING.LIB. If + not, write to the Free Software Foundation, Inc., + 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + Actually, this is a PPC (32bit) version, written based on the + i386, sparc, and sparc64 versions, by me, + Peter Maydell (pmaydell@chiark.greenend.org.uk). + Comments are by and large also mine, although they may be inaccurate. + + In picking out asm fragments I've gone with the lowest common + denominator, which also happens to be the hardware I have :-> + That is, a SPARC without hardware multiply and divide. + */ + +/* basic word size definitions */ +#define _FP_W_TYPE_SIZE 32 +#define _FP_W_TYPE unsigned long +#define _FP_WS_TYPE signed long +#define _FP_I_TYPE long + +#define __ll_B ((UWtype) 1 << (W_TYPE_SIZE / 2)) +#define __ll_lowpart(t) ((UWtype) (t) & (__ll_B - 1)) +#define __ll_highpart(t) ((UWtype) (t) >> (W_TYPE_SIZE / 2)) + +/* You can optionally code some things like addition in asm. For + * example, i386 defines __FP_FRAC_ADD_2 as asm. If you don't + * then you get a fragment of C code [if you change an #ifdef 0 + * in op-2.h] or a call to add_ssaaaa (see below). + * Good places to look for asm fragments to use are gcc and glibc. + * gcc's longlong.h is useful. + */ + +/* We need to know how to multiply and divide. If the host word size + * is >= 2*fracbits you can use FP_MUL_MEAT_n_imm(t,R,X,Y) which + * codes the multiply with whatever gcc does to 'a * b'. + * _FP_MUL_MEAT_n_wide(t,R,X,Y,f) is used when you have an asm + * function that can multiply two 1W values and get a 2W result. + * Otherwise you're stuck with _FP_MUL_MEAT_n_hard(t,R,X,Y) which + * does bitshifting to avoid overflow. + * For division there is FP_DIV_MEAT_n_imm(t,R,X,Y,f) for word size + * >= 2*fracbits, where f is either _FP_DIV_HELP_imm or + * _FP_DIV_HELP_ldiv (see op-1.h). + * _FP_DIV_MEAT_udiv() is if you have asm to do 2W/1W => (1W, 1W). + * [GCC and glibc have longlong.h which has the asm macro udiv_qrnnd + * to do this.] + * In general, 'n' is the number of words required to hold the type, + * and 't' is either S, D or Q for single/double/quad. + * -- PMM + */ +/* Example: SPARC64: + * #define _FP_MUL_MEAT_S(R,X,Y) _FP_MUL_MEAT_1_imm(S,R,X,Y) + * #define _FP_MUL_MEAT_D(R,X,Y) _FP_MUL_MEAT_1_wide(D,R,X,Y,umul_ppmm) + * #define _FP_MUL_MEAT_Q(R,X,Y) _FP_MUL_MEAT_2_wide(Q,R,X,Y,umul_ppmm) + * + * #define _FP_DIV_MEAT_S(R,X,Y) _FP_DIV_MEAT_1_imm(S,R,X,Y,_FP_DIV_HELP_imm) + * #define _FP_DIV_MEAT_D(R,X,Y) _FP_DIV_MEAT_1_udiv(D,R,X,Y) + * #define _FP_DIV_MEAT_Q(R,X,Y) _FP_DIV_MEAT_2_udiv_64(Q,R,X,Y) + * + * Example: i386: + * #define _FP_MUL_MEAT_S(R,X,Y) _FP_MUL_MEAT_1_wide(S,R,X,Y,_i386_mul_32_64) + * #define _FP_MUL_MEAT_D(R,X,Y) _FP_MUL_MEAT_2_wide(D,R,X,Y,_i386_mul_32_64) + * + * #define _FP_DIV_MEAT_S(R,X,Y) _FP_DIV_MEAT_1_udiv(S,R,X,Y,_i386_div_64_32) + * #define _FP_DIV_MEAT_D(R,X,Y) _FP_DIV_MEAT_2_udiv_64(D,R,X,Y) + */ + +#define _FP_MUL_MEAT_S(R,X,Y) _FP_MUL_MEAT_1_wide(_FP_WFRACBITS_S,R,X,Y,umul_ppmm) +#define _FP_MUL_MEAT_D(R,X,Y) _FP_MUL_MEAT_2_wide(_FP_WFRACBITS_D,R,X,Y,umul_ppmm) + +#define _FP_DIV_MEAT_S(R,X,Y) _FP_DIV_MEAT_1_udiv(S,R,X,Y) +#define _FP_DIV_MEAT_D(R,X,Y) _FP_DIV_MEAT_2_udiv(D,R,X,Y) + +/* These macros define what NaN looks like. They're supposed to expand to + * a comma-separated set of 32bit unsigned ints that encode NaN. + */ +#define _FP_NANFRAC_S ((_FP_QNANBIT_S << 1) - 1) +#define _FP_NANFRAC_D ((_FP_QNANBIT_D << 1) - 1), -1 +#define _FP_NANFRAC_Q ((_FP_QNANBIT_Q << 1) - 1), -1, -1, -1 +#define _FP_NANSIGN_S 0 +#define _FP_NANSIGN_D 0 +#define _FP_NANSIGN_Q 0 + +#define _FP_KEEPNANFRACP 1 + +/* Exception flags. We use the bit positions of the appropriate bits + in the FPSCR, which also correspond to the FE_* bits. This makes + everything easier ;-). */ +#define FP_EX_INVALID (1 << (31 - 2)) +#define FP_EX_INVALID_SNAN EFLAG_VXSNAN +#define FP_EX_INVALID_ISI EFLAG_VXISI +#define FP_EX_INVALID_IDI EFLAG_VXIDI +#define FP_EX_INVALID_ZDZ EFLAG_VXZDZ +#define FP_EX_INVALID_IMZ EFLAG_VXIMZ +#define FP_EX_OVERFLOW (1 << (31 - 3)) +#define FP_EX_UNDERFLOW (1 << (31 - 4)) +#define FP_EX_DIVZERO (1 << (31 - 5)) +#define FP_EX_INEXACT (1 << (31 - 6)) + +/* This macro appears to be called when both X and Y are NaNs, and + * has to choose one and copy it to R. i386 goes for the larger of the + * two, sparc64 just picks Y. I don't understand this at all so I'll + * go with sparc64 because it's shorter :-> -- PMM + */ +#define _FP_CHOOSENAN(fs, wc, R, X, Y, OP) \ + do { \ + R##_s = Y##_s; \ + _FP_FRAC_COPY_##wc(R,Y); \ + R##_c = FP_CLS_NAN; \ + } while (0) + + +#include +#include + +#define __FPU_FPSCR (current->thread.fpscr.val) + +/* We only actually write to the destination register + * if exceptions signalled (if any) will not trap. + */ +#define __FPU_ENABLED_EXC \ +({ \ + (__FPU_FPSCR >> 3) & 0x1f; \ +}) + +#define __FPU_TRAP_P(bits) \ + ((__FPU_ENABLED_EXC & (bits)) != 0) + +#define __FP_PACK_S(val,X) \ +({ int __exc = _FP_PACK_CANONICAL(S,1,X); \ + if(!__exc || !__FPU_TRAP_P(__exc)) \ + _FP_PACK_RAW_1_P(S,val,X); \ + __exc; \ +}) + +#define __FP_PACK_D(val,X) \ + do { \ + _FP_PACK_CANONICAL(D, 2, X); \ + if (!FP_CUR_EXCEPTIONS || !__FPU_TRAP_P(FP_CUR_EXCEPTIONS)) \ + _FP_PACK_RAW_2_P(D, val, X); \ + } while (0) + +#define __FP_PACK_DS(val,X) \ + do { \ + FP_DECL_S(__X); \ + FP_CONV(S, D, 1, 2, __X, X); \ + _FP_PACK_CANONICAL(S, 1, __X); \ + if (!FP_CUR_EXCEPTIONS || !__FPU_TRAP_P(FP_CUR_EXCEPTIONS)) { \ + _FP_UNPACK_CANONICAL(S, 1, __X); \ + FP_CONV(D, S, 2, 1, X, __X); \ + _FP_PACK_CANONICAL(D, 2, X); \ + if (!FP_CUR_EXCEPTIONS || !__FPU_TRAP_P(FP_CUR_EXCEPTIONS)) \ + _FP_PACK_RAW_2_P(D, val, X); \ + } \ + } while (0) + +/* Obtain the current rounding mode. */ +#define FP_ROUNDMODE \ +({ \ + __FPU_FPSCR & 0x3; \ +}) + +/* the asm fragments go here: all these are taken from glibc-2.0.5's + * stdlib/longlong.h + */ + +#include +#include + +/* add_ssaaaa is used in op-2.h and should be equivalent to + * #define add_ssaaaa(sh,sl,ah,al,bh,bl) (sh = ah+bh+ (( sl = al+bl) < al)) + * add_ssaaaa(high_sum, low_sum, high_addend_1, low_addend_1, + * high_addend_2, low_addend_2) adds two UWtype integers, composed by + * HIGH_ADDEND_1 and LOW_ADDEND_1, and HIGH_ADDEND_2 and LOW_ADDEND_2 + * respectively. The result is placed in HIGH_SUM and LOW_SUM. Overflow + * (i.e. carry out) is not stored anywhere, and is lost. + */ +#define add_ssaaaa(sh, sl, ah, al, bh, bl) \ + do { \ + if (__builtin_constant_p (bh) && (bh) == 0) \ + __asm__ ("{a%I4|add%I4c} %1,%3,%4\n\t{aze|addze} %0,%2" \ + : "=r" ((USItype)(sh)), \ + "=&r" ((USItype)(sl)) \ + : "%r" ((USItype)(ah)), \ + "%r" ((USItype)(al)), \ + "rI" ((USItype)(bl))); \ + else if (__builtin_constant_p (bh) && (bh) ==~(USItype) 0) \ + __asm__ ("{a%I4|add%I4c} %1,%3,%4\n\t{ame|addme} %0,%2" \ + : "=r" ((USItype)(sh)), \ + "=&r" ((USItype)(sl)) \ + : "%r" ((USItype)(ah)), \ + "%r" ((USItype)(al)), \ + "rI" ((USItype)(bl))); \ + else \ + __asm__ ("{a%I5|add%I5c} %1,%4,%5\n\t{ae|adde} %0,%2,%3" \ + : "=r" ((USItype)(sh)), \ + "=&r" ((USItype)(sl)) \ + : "%r" ((USItype)(ah)), \ + "r" ((USItype)(bh)), \ + "%r" ((USItype)(al)), \ + "rI" ((USItype)(bl))); \ + } while (0) + +/* sub_ddmmss is used in op-2.h and udivmodti4.c and should be equivalent to + * #define sub_ddmmss(sh, sl, ah, al, bh, bl) (sh = ah-bh - ((sl = al-bl) > al)) + * sub_ddmmss(high_difference, low_difference, high_minuend, low_minuend, + * high_subtrahend, low_subtrahend) subtracts two two-word UWtype integers, + * composed by HIGH_MINUEND_1 and LOW_MINUEND_1, and HIGH_SUBTRAHEND_2 and + * LOW_SUBTRAHEND_2 respectively. The result is placed in HIGH_DIFFERENCE + * and LOW_DIFFERENCE. Overflow (i.e. carry out) is not stored anywhere, + * and is lost. + */ +#define sub_ddmmss(sh, sl, ah, al, bh, bl) \ + do { \ + if (__builtin_constant_p (ah) && (ah) == 0) \ + __asm__ ("{sf%I3|subf%I3c} %1,%4,%3\n\t{sfze|subfze} %0,%2" \ + : "=r" ((USItype)(sh)), \ + "=&r" ((USItype)(sl)) \ + : "r" ((USItype)(bh)), \ + "rI" ((USItype)(al)), \ + "r" ((USItype)(bl))); \ + else if (__builtin_constant_p (ah) && (ah) ==~(USItype) 0) \ + __asm__ ("{sf%I3|subf%I3c} %1,%4,%3\n\t{sfme|subfme} %0,%2" \ + : "=r" ((USItype)(sh)), \ + "=&r" ((USItype)(sl)) \ + : "r" ((USItype)(bh)), \ + "rI" ((USItype)(al)), \ + "r" ((USItype)(bl))); \ + else if (__builtin_constant_p (bh) && (bh) == 0) \ + __asm__ ("{sf%I3|subf%I3c} %1,%4,%3\n\t{ame|addme} %0,%2" \ + : "=r" ((USItype)(sh)), \ + "=&r" ((USItype)(sl)) \ + : "r" ((USItype)(ah)), \ + "rI" ((USItype)(al)), \ + "r" ((USItype)(bl))); \ + else if (__builtin_constant_p (bh) && (bh) ==~(USItype) 0) \ + __asm__ ("{sf%I3|subf%I3c} %1,%4,%3\n\t{aze|addze} %0,%2" \ + : "=r" ((USItype)(sh)), \ + "=&r" ((USItype)(sl)) \ + : "r" ((USItype)(ah)), \ + "rI" ((USItype)(al)), \ + "r" ((USItype)(bl))); \ + else \ + __asm__ ("{sf%I4|subf%I4c} %1,%5,%4\n\t{sfe|subfe} %0,%3,%2" \ + : "=r" ((USItype)(sh)), \ + "=&r" ((USItype)(sl)) \ + : "r" ((USItype)(ah)), \ + "r" ((USItype)(bh)), \ + "rI" ((USItype)(al)), \ + "r" ((USItype)(bl))); \ + } while (0) + +/* asm fragments for mul and div */ + +/* umul_ppmm(high_prod, low_prod, multipler, multiplicand) multiplies two + * UWtype integers MULTIPLER and MULTIPLICAND, and generates a two UWtype + * word product in HIGH_PROD and LOW_PROD. + */ +#define umul_ppmm(ph, pl, m0, m1) \ + do { \ + USItype __m0 = (m0), __m1 = (m1); \ + __asm__ ("mulhwu %0,%1,%2" \ + : "=r" ((USItype)(ph)) \ + : "%r" (__m0), \ + "r" (__m1)); \ + (pl) = __m0 * __m1; \ + } while (0) + +/* udiv_qrnnd(quotient, remainder, high_numerator, low_numerator, + * denominator) divides a UDWtype, composed by the UWtype integers + * HIGH_NUMERATOR and LOW_NUMERATOR, by DENOMINATOR and places the quotient + * in QUOTIENT and the remainder in REMAINDER. HIGH_NUMERATOR must be less + * than DENOMINATOR for correct operation. If, in addition, the most + * significant bit of DENOMINATOR must be 1, then the pre-processor symbol + * UDIV_NEEDS_NORMALIZATION is defined to 1. + */ +#define udiv_qrnnd(q, r, n1, n0, d) \ + do { \ + UWtype __d1, __d0, __q1, __q0, __r1, __r0, __m; \ + __d1 = __ll_highpart (d); \ + __d0 = __ll_lowpart (d); \ + \ + __r1 = (n1) % __d1; \ + __q1 = (n1) / __d1; \ + __m = (UWtype) __q1 * __d0; \ + __r1 = __r1 * __ll_B | __ll_highpart (n0); \ + if (__r1 < __m) \ + { \ + __q1--, __r1 += (d); \ + if (__r1 >= (d)) /* we didn't get carry when adding to __r1 */ \ + if (__r1 < __m) \ + __q1--, __r1 += (d); \ + } \ + __r1 -= __m; \ + \ + __r0 = __r1 % __d1; \ + __q0 = __r1 / __d1; \ + __m = (UWtype) __q0 * __d0; \ + __r0 = __r0 * __ll_B | __ll_lowpart (n0); \ + if (__r0 < __m) \ + { \ + __q0--, __r0 += (d); \ + if (__r0 >= (d)) \ + if (__r0 < __m) \ + __q0--, __r0 += (d); \ + } \ + __r0 -= __m; \ + \ + (q) = (UWtype) __q1 * __ll_B | __q0; \ + (r) = __r0; \ + } while (0) + +#define UDIV_NEEDS_NORMALIZATION 1 + +#define abort() \ + return 0 + +#ifdef __BIG_ENDIAN +#define __BYTE_ORDER __BIG_ENDIAN +#else +#define __BYTE_ORDER __LITTLE_ENDIAN +#endif + +/* Exception flags. */ +#define EFLAG_INVALID (1 << (31 - 2)) +#define EFLAG_OVERFLOW (1 << (31 - 3)) +#define EFLAG_UNDERFLOW (1 << (31 - 4)) +#define EFLAG_DIVZERO (1 << (31 - 5)) +#define EFLAG_INEXACT (1 << (31 - 6)) + +#define EFLAG_VXSNAN (1 << (31 - 7)) +#define EFLAG_VXISI (1 << (31 - 8)) +#define EFLAG_VXIDI (1 << (31 - 9)) +#define EFLAG_VXZDZ (1 << (31 - 10)) +#define EFLAG_VXIMZ (1 << (31 - 11)) +#define EFLAG_VXVC (1 << (31 - 12)) +#define EFLAG_VXSOFT (1 << (31 - 21)) +#define EFLAG_VXSQRT (1 << (31 - 22)) +#define EFLAG_VXCVI (1 << (31 - 23)) diff --git a/arch/powerpc/math-emu/Makefile b/arch/powerpc/math-emu/Makefile index 29bc9126241..03aa98dd9f0 100644 --- a/arch/powerpc/math-emu/Makefile +++ b/arch/powerpc/math-emu/Makefile @@ -4,13 +4,14 @@ obj-y := math.o fmr.o lfd.o stfd.o obj-$(CONFIG_MATH_EMULATION) += fabs.o fadd.o fadds.o fcmpo.o fcmpu.o \ fctiw.o fctiwz.o fdiv.o fdivs.o \ fmadd.o fmadds.o fmsub.o fmsubs.o \ - fmul.o fmuls.o fnabs.o fneg.o types.o \ + fmul.o fmuls.o fnabs.o fneg.o \ fnmadd.o fnmadds.o fnmsub.o fnmsubs.o \ fres.o frsp.o frsqrte.o fsel.o lfs.o \ fsqrt.o fsqrts.o fsub.o fsubs.o \ mcrfs.o mffs.o mtfsb0.o mtfsb1.o \ - mtfsf.o mtfsfi.o stfiwx.o stfs.o \ - udivmodti4.o + mtfsf.o mtfsfi.o stfiwx.o stfs.o CFLAGS_fabs.o = -fno-builtin-fabs CFLAGS_math.o = -fno-builtin-fabs + +EXTRA_CFLAGS = -I. -Iinclude/math-emu -w diff --git a/arch/powerpc/math-emu/double.h b/arch/powerpc/math-emu/double.h deleted file mode 100644 index ffba8b67f05..00000000000 --- a/arch/powerpc/math-emu/double.h +++ /dev/null @@ -1,129 +0,0 @@ -/* - * Definitions for IEEE Double Precision - */ - -#if _FP_W_TYPE_SIZE < 32 -#error "Here's a nickel kid. Go buy yourself a real computer." -#endif - -#if _FP_W_TYPE_SIZE < 64 -#define _FP_FRACTBITS_D (2 * _FP_W_TYPE_SIZE) -#else -#define _FP_FRACTBITS_D _FP_W_TYPE_SIZE -#endif - -#define _FP_FRACBITS_D 53 -#define _FP_FRACXBITS_D (_FP_FRACTBITS_D - _FP_FRACBITS_D) -#define _FP_WFRACBITS_D (_FP_WORKBITS + _FP_FRACBITS_D) -#define _FP_WFRACXBITS_D (_FP_FRACTBITS_D - _FP_WFRACBITS_D) -#define _FP_EXPBITS_D 11 -#define _FP_EXPBIAS_D 1023 -#define _FP_EXPMAX_D 2047 - -#define _FP_QNANBIT_D \ - ((_FP_W_TYPE)1 << ((_FP_FRACBITS_D-2) % _FP_W_TYPE_SIZE)) -#define _FP_IMPLBIT_D \ - ((_FP_W_TYPE)1 << ((_FP_FRACBITS_D-1) % _FP_W_TYPE_SIZE)) -#define _FP_OVERFLOW_D \ - ((_FP_W_TYPE)1 << (_FP_WFRACBITS_D % _FP_W_TYPE_SIZE)) - -#if _FP_W_TYPE_SIZE < 64 - -union _FP_UNION_D -{ - double flt; - struct { -#if __BYTE_ORDER == __BIG_ENDIAN - unsigned sign : 1; - unsigned exp : _FP_EXPBITS_D; - unsigned frac1 : _FP_FRACBITS_D - (_FP_IMPLBIT_D != 0) - _FP_W_TYPE_SIZE; - unsigned frac0 : _FP_W_TYPE_SIZE; -#else - unsigned frac0 : _FP_W_TYPE_SIZE; - unsigned frac1 : _FP_FRACBITS_D - (_FP_IMPLBIT_D != 0) - _FP_W_TYPE_SIZE; - unsigned exp : _FP_EXPBITS_D; - unsigned sign : 1; -#endif - } bits __attribute__((packed)); -}; - -#define FP_DECL_D(X) _FP_DECL(2,X) -#define FP_UNPACK_RAW_D(X,val) _FP_UNPACK_RAW_2(D,X,val) -#define FP_PACK_RAW_D(val,X) _FP_PACK_RAW_2(D,val,X) - -#define FP_UNPACK_D(X,val) \ - do { \ - _FP_UNPACK_RAW_2(D,X,val); \ - _FP_UNPACK_CANONICAL(D,2,X); \ - } while (0) - -#define FP_PACK_D(val,X) \ - do { \ - _FP_PACK_CANONICAL(D,2,X); \ - _FP_PACK_RAW_2(D,val,X); \ - } while (0) - -#define FP_NEG_D(R,X) _FP_NEG(D,2,R,X) -#define FP_ADD_D(R,X,Y) _FP_ADD(D,2,R,X,Y) -#define FP_SUB_D(R,X,Y) _FP_SUB(D,2,R,X,Y) -#define FP_MUL_D(R,X,Y) _FP_MUL(D,2,R,X,Y) -#define FP_DIV_D(R,X,Y) _FP_DIV(D,2,R,X,Y) -#define FP_SQRT_D(R,X) _FP_SQRT(D,2,R,X) - -#define FP_CMP_D(r,X,Y,un) _FP_CMP(D,2,r,X,Y,un) -#define FP_CMP_EQ_D(r,X,Y) _FP_CMP_EQ(D,2,r,X,Y) - -#define FP_TO_INT_D(r,X,rsz,rsg) _FP_TO_INT(D,2,r,X,rsz,rsg) -#define FP_FROM_INT_D(X,r,rs,rt) _FP_FROM_INT(D,2,X,r,rs,rt) - -#else - -union _FP_UNION_D -{ - double flt; - struct { -#if __BYTE_ORDER == __BIG_ENDIAN - unsigned sign : 1; - unsigned exp : _FP_EXPBITS_D; - unsigned long frac : _FP_FRACBITS_D - (_FP_IMPLBIT_D != 0); -#else - unsigned long frac : _FP_FRACBITS_D - (_FP_IMPLBIT_D != 0); - unsigned exp : _FP_EXPBITS_D; - unsigned sign : 1; -#endif - } bits __attribute__((packed)); -}; - -#define FP_DECL_D(X) _FP_DECL(1,X) -#define FP_UNPACK_RAW_D(X,val) _FP_UNPACK_RAW_1(D,X,val) -#define FP_PACK_RAW_D(val,X) _FP_PACK_RAW_1(D,val,X) - -#define FP_UNPACK_D(X,val) \ - do { \ - _FP_UNPACK_RAW_1(D,X,val); \ - _FP_UNPACK_CANONICAL(D,1,X); \ - } while (0) - -#define FP_PACK_D(val,X) \ - do { \ - _FP_PACK_CANONICAL(D,1,X); \ - _FP_PACK_RAW_1(D,val,X); \ - } while (0) - -#define FP_NEG_D(R,X) _FP_NEG(D,1,R,X) -#define FP_ADD_D(R,X,Y) _FP_ADD(D,1,R,X,Y) -#define FP_SUB_D(R,X,Y) _FP_SUB(D,1,R,X,Y) -#define FP_MUL_D(R,X,Y) _FP_MUL(D,1,R,X,Y) -#define FP_DIV_D(R,X,Y) _FP_DIV(D,1,R,X,Y) -#define FP_SQRT_D(R,X) _FP_SQRT(D,1,R,X) - -/* The implementation of _FP_MUL_D and _FP_DIV_D should be chosen by - the target machine. */ - -#define FP_CMP_D(r,X,Y,un) _FP_CMP(D,1,r,X,Y,un) -#define FP_CMP_EQ_D(r,X,Y) _FP_CMP_EQ(D,1,r,X,Y) - -#define FP_TO_INT_D(r,X,rsz,rsg) _FP_TO_INT(D,1,r,X,rsz,rsg) -#define FP_FROM_INT_D(X,r,rs,rt) _FP_FROM_INT(D,1,X,r,rs,rt) - -#endif /* W_TYPE_SIZE < 64 */ diff --git a/arch/powerpc/math-emu/fadd.c b/arch/powerpc/math-emu/fadd.c index 7befbbf2c33..04d3b4aa32c 100644 --- a/arch/powerpc/math-emu/fadd.c +++ b/arch/powerpc/math-emu/fadd.c @@ -2,8 +2,9 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fadd(void *frD, void *frA, void *frB) @@ -11,28 +12,28 @@ fadd(void *frD, void *frA, void *frB) FP_DECL_D(A); FP_DECL_D(B); FP_DECL_D(R); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p\n", __func__, frD, frA, frB); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); printk("B: %ld %lu %lu %ld (%ld)\n", B_s, B_f1, B_f0, B_e, B_c); #endif - if (A_s != B_s && A_c == FP_CLS_INF && B_c == FP_CLS_INF) - ret |= EFLAG_VXISI; - FP_ADD_D(R, A, B); #ifdef DEBUG printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_D(frD, R)); + __FP_PACK_D(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fadds.c b/arch/powerpc/math-emu/fadds.c index 2b346b38b48..5930f40a868 100644 --- a/arch/powerpc/math-emu/fadds.c +++ b/arch/powerpc/math-emu/fadds.c @@ -2,9 +2,10 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int fadds(void *frD, void *frA, void *frB) @@ -12,28 +13,27 @@ fadds(void *frD, void *frA, void *frB) FP_DECL_D(A); FP_DECL_D(B); FP_DECL_D(R); - int ret = 0; + FP_DECL_EX; #ifdef DEBUG printk("%s: %p %p %p\n", __func__, frD, frA, frB); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); printk("B: %ld %lu %lu %ld (%ld)\n", B_s, B_f1, B_f0, B_e, B_c); #endif - if (A_s != B_s && A_c == FP_CLS_INF && B_c == FP_CLS_INF) - ret |= EFLAG_VXISI; - FP_ADD_D(R, A, B); #ifdef DEBUG printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_DS(frD, R)); + __FP_PACK_DS(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fcmpo.c b/arch/powerpc/math-emu/fcmpo.c index 36d689044c6..b5dc4498cd7 100644 --- a/arch/powerpc/math-emu/fcmpo.c +++ b/arch/powerpc/math-emu/fcmpo.c @@ -2,14 +2,16 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fcmpo(u32 *ccr, int crfD, void *frA, void *frB) { FP_DECL_D(A); FP_DECL_D(B); + FP_DECL_EX; int code[4] = { (1 << 3), (1 << 1), (1 << 2), (1 << 0) }; long cmp; int ret = 0; @@ -18,8 +20,8 @@ fcmpo(u32 *ccr, int crfD, void *frA, void *frB) printk("%s: %p (%08x) %d %p %p\n", __func__, ccr, *ccr, crfD, frA, frB); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); diff --git a/arch/powerpc/math-emu/fcmpu.c b/arch/powerpc/math-emu/fcmpu.c index 53d93894f2a..d4fb1babc6a 100644 --- a/arch/powerpc/math-emu/fcmpu.c +++ b/arch/powerpc/math-emu/fcmpu.c @@ -2,14 +2,16 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fcmpu(u32 *ccr, int crfD, void *frA, void *frB) { FP_DECL_D(A); FP_DECL_D(B); + FP_DECL_EX; int code[4] = { (1 << 3), (1 << 1), (1 << 2), (1 << 0) }; long cmp; @@ -17,8 +19,8 @@ fcmpu(u32 *ccr, int crfD, void *frA, void *frB) printk("%s: %p (%08x) %d %p %p\n", __func__, ccr, *ccr, crfD, frA, frB); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); diff --git a/arch/powerpc/math-emu/fctiw.c b/arch/powerpc/math-emu/fctiw.c index fcd7a95e021..f694440ddc0 100644 --- a/arch/powerpc/math-emu/fctiw.c +++ b/arch/powerpc/math-emu/fctiw.c @@ -2,16 +2,18 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fctiw(u32 *frD, void *frB) { FP_DECL_D(B); + FP_DECL_EX; unsigned int r; - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(B, frB); FP_TO_INT_D(r, B, 32, 1); frD[1] = r; diff --git a/arch/powerpc/math-emu/fctiwz.c b/arch/powerpc/math-emu/fctiwz.c index 1514d59e146..71e782fd4fe 100644 --- a/arch/powerpc/math-emu/fctiwz.c +++ b/arch/powerpc/math-emu/fctiwz.c @@ -2,13 +2,15 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fctiwz(u32 *frD, void *frB) { FP_DECL_D(B); + FP_DECL_EX; u32 fpscr; unsigned int r; @@ -16,7 +18,7 @@ fctiwz(u32 *frD, void *frB) __FPU_FPSCR &= ~(3); __FPU_FPSCR |= FP_RND_ZERO; - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(B, frB); FP_TO_INT_D(r, B, 32, 1); frD[1] = r; diff --git a/arch/powerpc/math-emu/fdiv.c b/arch/powerpc/math-emu/fdiv.c index 18a20fe396b..2db15097d98 100644 --- a/arch/powerpc/math-emu/fdiv.c +++ b/arch/powerpc/math-emu/fdiv.c @@ -2,8 +2,9 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fdiv(void *frD, void *frA, void *frB) @@ -11,14 +12,15 @@ fdiv(void *frD, void *frA, void *frB) FP_DECL_D(A); FP_DECL_D(B); FP_DECL_D(R); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p\n", __func__, frD, frA, frB); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -49,5 +51,7 @@ fdiv(void *frD, void *frA, void *frB) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_D(frD, R)); + __FP_PACK_D(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fdivs.c b/arch/powerpc/math-emu/fdivs.c index 24feed689c3..797f6a9a20b 100644 --- a/arch/powerpc/math-emu/fdivs.c +++ b/arch/powerpc/math-emu/fdivs.c @@ -2,9 +2,10 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int fdivs(void *frD, void *frA, void *frB) @@ -12,14 +13,15 @@ fdivs(void *frD, void *frA, void *frB) FP_DECL_D(A); FP_DECL_D(B); FP_DECL_D(R); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p\n", __func__, frD, frA, frB); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -51,5 +53,7 @@ fdivs(void *frD, void *frA, void *frB) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_DS(frD, R)); + __FP_PACK_DS(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fmadd.c b/arch/powerpc/math-emu/fmadd.c index dedb465fdc6..925313aa6f8 100644 --- a/arch/powerpc/math-emu/fmadd.c +++ b/arch/powerpc/math-emu/fmadd.c @@ -2,8 +2,9 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fmadd(void *frD, void *frA, void *frB, void *frC) @@ -13,15 +14,16 @@ fmadd(void *frD, void *frA, void *frB, void *frC) FP_DECL_D(B); FP_DECL_D(C); FP_DECL_D(T); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frA, frB, frC); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); - __FP_UNPACK_D(C, frC); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); + FP_UNPACK_DP(C, frC); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -44,5 +46,7 @@ fmadd(void *frD, void *frA, void *frB, void *frC) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_D(frD, R)); + __FP_PACK_D(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fmadds.c b/arch/powerpc/math-emu/fmadds.c index 6bbb56d5502..aea80ef7939 100644 --- a/arch/powerpc/math-emu/fmadds.c +++ b/arch/powerpc/math-emu/fmadds.c @@ -2,9 +2,10 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int fmadds(void *frD, void *frA, void *frB, void *frC) @@ -14,15 +15,16 @@ fmadds(void *frD, void *frA, void *frB, void *frC) FP_DECL_D(B); FP_DECL_D(C); FP_DECL_D(T); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frA, frB, frC); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); - __FP_UNPACK_D(C, frC); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); + FP_UNPACK_DP(C, frC); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -45,5 +47,7 @@ fmadds(void *frD, void *frA, void *frB, void *frC) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_DS(frD, R)); + __FP_PACK_DS(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fmsub.c b/arch/powerpc/math-emu/fmsub.c index f311e2c7e67..a644d525fca 100644 --- a/arch/powerpc/math-emu/fmsub.c +++ b/arch/powerpc/math-emu/fmsub.c @@ -2,8 +2,9 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fmsub(void *frD, void *frA, void *frB, void *frC) @@ -13,15 +14,16 @@ fmsub(void *frD, void *frA, void *frB, void *frC) FP_DECL_D(B); FP_DECL_D(C); FP_DECL_D(T); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frA, frB, frC); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); - __FP_UNPACK_D(C, frC); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); + FP_UNPACK_DP(C, frC); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -47,5 +49,7 @@ fmsub(void *frD, void *frA, void *frB, void *frC) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_D(frD, R)); + __FP_PACK_D(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fmsubs.c b/arch/powerpc/math-emu/fmsubs.c index 81a716d3ee2..2fdeeb9bb56 100644 --- a/arch/powerpc/math-emu/fmsubs.c +++ b/arch/powerpc/math-emu/fmsubs.c @@ -2,9 +2,10 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int fmsubs(void *frD, void *frA, void *frB, void *frC) @@ -14,15 +15,16 @@ fmsubs(void *frD, void *frA, void *frB, void *frC) FP_DECL_D(B); FP_DECL_D(C); FP_DECL_D(T); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frA, frB, frC); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); - __FP_UNPACK_D(C, frC); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); + FP_UNPACK_DP(C, frC); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -48,5 +50,7 @@ fmsubs(void *frD, void *frA, void *frB, void *frC) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_DS(frD, R)); + __FP_PACK_DS(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fmul.c b/arch/powerpc/math-emu/fmul.c index 2f3d32784a0..391fd17d344 100644 --- a/arch/powerpc/math-emu/fmul.c +++ b/arch/powerpc/math-emu/fmul.c @@ -2,8 +2,9 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fmul(void *frD, void *frA, void *frB) @@ -11,14 +12,15 @@ fmul(void *frD, void *frA, void *frB) FP_DECL_D(A); FP_DECL_D(B); FP_DECL_D(R); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p\n", __func__, frD, frA, frB); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld) [%08lx.%08lx %lx]\n", @@ -38,5 +40,7 @@ fmul(void *frD, void *frA, void *frB) R_s, R_f1, R_f0, R_e, R_c, R_f1, R_f0, R_e + 1023); #endif - return (ret | __FP_PACK_D(frD, R)); + __FP_PACK_D(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fmuls.c b/arch/powerpc/math-emu/fmuls.c index 962b5883f78..2d3ec5f7da2 100644 --- a/arch/powerpc/math-emu/fmuls.c +++ b/arch/powerpc/math-emu/fmuls.c @@ -2,9 +2,10 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int fmuls(void *frD, void *frA, void *frB) @@ -12,14 +13,15 @@ fmuls(void *frD, void *frA, void *frB) FP_DECL_D(A); FP_DECL_D(B); FP_DECL_D(R); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p\n", __func__, frD, frA, frB); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld) [%08lx.%08lx %lx]\n", @@ -39,5 +41,7 @@ fmuls(void *frD, void *frA, void *frB) R_s, R_f1, R_f0, R_e, R_c, R_f1, R_f0, R_e + 1023); #endif - return (ret | __FP_PACK_DS(frD, R)); + __FP_PACK_DS(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fnmadd.c b/arch/powerpc/math-emu/fnmadd.c index 8cf7827c4fb..2497b86494e 100644 --- a/arch/powerpc/math-emu/fnmadd.c +++ b/arch/powerpc/math-emu/fnmadd.c @@ -2,8 +2,9 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fnmadd(void *frD, void *frA, void *frB, void *frC) @@ -13,15 +14,16 @@ fnmadd(void *frD, void *frA, void *frB, void *frC) FP_DECL_D(B); FP_DECL_D(C); FP_DECL_D(T); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frA, frB, frC); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); - __FP_UNPACK_D(C, frC); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); + FP_UNPACK_DP(C, frC); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -47,5 +49,7 @@ fnmadd(void *frD, void *frA, void *frB, void *frC) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_D(frD, R)); + __FP_PACK_D(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fnmadds.c b/arch/powerpc/math-emu/fnmadds.c index f1c4f0f0d80..ee9d71e0b37 100644 --- a/arch/powerpc/math-emu/fnmadds.c +++ b/arch/powerpc/math-emu/fnmadds.c @@ -2,9 +2,10 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int fnmadds(void *frD, void *frA, void *frB, void *frC) @@ -14,15 +15,16 @@ fnmadds(void *frD, void *frA, void *frB, void *frC) FP_DECL_D(B); FP_DECL_D(C); FP_DECL_D(T); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frA, frB, frC); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); - __FP_UNPACK_D(C, frC); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); + FP_UNPACK_DP(C, frC); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -48,5 +50,7 @@ fnmadds(void *frD, void *frA, void *frB, void *frC) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_DS(frD, R)); + __FP_PACK_DS(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fnmsub.c b/arch/powerpc/math-emu/fnmsub.c index 98944e6e260..3885a77acc9 100644 --- a/arch/powerpc/math-emu/fnmsub.c +++ b/arch/powerpc/math-emu/fnmsub.c @@ -2,8 +2,9 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fnmsub(void *frD, void *frA, void *frB, void *frC) @@ -13,15 +14,16 @@ fnmsub(void *frD, void *frA, void *frB, void *frC) FP_DECL_D(B); FP_DECL_D(C); FP_DECL_D(T); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frA, frB, frC); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); - __FP_UNPACK_D(C, frC); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); + FP_UNPACK_DP(C, frC); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -50,5 +52,7 @@ fnmsub(void *frD, void *frA, void *frB, void *frC) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_D(frD, R)); + __FP_PACK_D(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fnmsubs.c b/arch/powerpc/math-emu/fnmsubs.c index b20f4eb63fb..f835dfeb0fd 100644 --- a/arch/powerpc/math-emu/fnmsubs.c +++ b/arch/powerpc/math-emu/fnmsubs.c @@ -2,9 +2,10 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int fnmsubs(void *frD, void *frA, void *frB, void *frC) @@ -14,15 +15,16 @@ fnmsubs(void *frD, void *frA, void *frB, void *frC) FP_DECL_D(B); FP_DECL_D(C); FP_DECL_D(T); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frA, frB, frC); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); - __FP_UNPACK_D(C, frC); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); + FP_UNPACK_DP(C, frC); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -51,5 +53,7 @@ fnmsubs(void *frD, void *frA, void *frB, void *frC) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_DS(frD, R)); + __FP_PACK_DS(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/frsp.c b/arch/powerpc/math-emu/frsp.c index 724ccbc0468..ddcc14664b1 100644 --- a/arch/powerpc/math-emu/frsp.c +++ b/arch/powerpc/math-emu/frsp.c @@ -2,24 +2,28 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int frsp(void *frD, void *frB) { FP_DECL_D(B); + FP_DECL_EX; #ifdef DEBUG printk("%s: D %p, B %p\n", __func__, frD, frB); #endif - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("B: %ld %lu %lu %ld (%ld)\n", B_s, B_f1, B_f0, B_e, B_c); #endif - return __FP_PACK_DS(frD, B); + __FP_PACK_DS(frD, B); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fsel.c b/arch/powerpc/math-emu/fsel.c index ecb5f28eb1f..1b0c1449803 100644 --- a/arch/powerpc/math-emu/fsel.c +++ b/arch/powerpc/math-emu/fsel.c @@ -2,19 +2,21 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fsel(u32 *frD, void *frA, u32 *frB, u32 *frC) { FP_DECL_D(A); + FP_DECL_EX; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frA, frB, frC); #endif - __FP_UNPACK_D(A, frA); + FP_UNPACK_DP(A, frA); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); diff --git a/arch/powerpc/math-emu/fsqrt.c b/arch/powerpc/math-emu/fsqrt.c index 38ec2b752e9..3e90072693a 100644 --- a/arch/powerpc/math-emu/fsqrt.c +++ b/arch/powerpc/math-emu/fsqrt.c @@ -2,21 +2,23 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fsqrt(void *frD, void *frB) { FP_DECL_D(B); FP_DECL_D(R); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frB); #endif - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("B: %ld %lu %lu %ld (%ld)\n", B_s, B_f1, B_f0, B_e, B_c); @@ -33,5 +35,7 @@ fsqrt(void *frD, void *frB) printk("R: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_D(frD, R)); + __FP_PACK_D(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fsqrts.c b/arch/powerpc/math-emu/fsqrts.c index 335263e06ee..2843be986e2 100644 --- a/arch/powerpc/math-emu/fsqrts.c +++ b/arch/powerpc/math-emu/fsqrts.c @@ -2,22 +2,24 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int fsqrts(void *frD, void *frB) { FP_DECL_D(B); FP_DECL_D(R); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p %p\n", __func__, frD, frB); #endif - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("B: %ld %lu %lu %ld (%ld)\n", B_s, B_f1, B_f0, B_e, B_c); @@ -34,5 +36,7 @@ fsqrts(void *frD, void *frB) printk("R: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_DS(frD, R)); + __FP_PACK_DS(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fsub.c b/arch/powerpc/math-emu/fsub.c index 208d20fc52a..78b09446a0e 100644 --- a/arch/powerpc/math-emu/fsub.c +++ b/arch/powerpc/math-emu/fsub.c @@ -2,8 +2,9 @@ #include #include -#include "soft-fp.h" -#include "double.h" +#include +#include +#include int fsub(void *frD, void *frA, void *frB) @@ -11,14 +12,15 @@ fsub(void *frD, void *frA, void *frB) FP_DECL_D(A); FP_DECL_D(B); FP_DECL_D(R); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p\n", __func__, frD, frA, frB); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -37,5 +39,7 @@ fsub(void *frD, void *frA, void *frB) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_D(frD, R)); + __FP_PACK_D(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/fsubs.c b/arch/powerpc/math-emu/fsubs.c index 0e61b808c44..d3bf90863cf 100644 --- a/arch/powerpc/math-emu/fsubs.c +++ b/arch/powerpc/math-emu/fsubs.c @@ -2,9 +2,10 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int fsubs(void *frD, void *frA, void *frB) @@ -12,14 +13,15 @@ fsubs(void *frD, void *frA, void *frB) FP_DECL_D(A); FP_DECL_D(B); FP_DECL_D(R); + FP_DECL_EX; int ret = 0; #ifdef DEBUG printk("%s: %p %p %p\n", __func__, frD, frA, frB); #endif - __FP_UNPACK_D(A, frA); - __FP_UNPACK_D(B, frB); + FP_UNPACK_DP(A, frA); + FP_UNPACK_DP(B, frB); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -38,5 +40,7 @@ fsubs(void *frD, void *frA, void *frB) printk("D: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return (ret | __FP_PACK_DS(frD, R)); + __FP_PACK_DS(frD, R); + + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/lfd.c b/arch/powerpc/math-emu/lfd.c index 6ec90b57c61..79ac76d596c 100644 --- a/arch/powerpc/math-emu/lfd.c +++ b/arch/powerpc/math-emu/lfd.c @@ -2,8 +2,8 @@ #include #include -#include "sfp-machine.h" -#include "double.h" +#include +#include int lfd(void *frD, void *ea) diff --git a/arch/powerpc/math-emu/lfs.c b/arch/powerpc/math-emu/lfs.c index 6f18ebe3a7f..434ed27be8d 100644 --- a/arch/powerpc/math-emu/lfs.c +++ b/arch/powerpc/math-emu/lfs.c @@ -2,15 +2,17 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int lfs(void *frD, void *ea) { FP_DECL_D(R); FP_DECL_S(A); + FP_DECL_EX; float f; #ifdef DEBUG @@ -20,7 +22,7 @@ lfs(void *frD, void *ea) if (copy_from_user(&f, ea, sizeof(float))) return -EFAULT; - __FP_UNPACK_S(A, &f); + FP_UNPACK_S(A, f); #ifdef DEBUG printk("A: %ld %lu %ld (%ld) [%08lx]\n", A_s, A_f, A_e, A_c, @@ -33,5 +35,12 @@ lfs(void *frD, void *ea) printk("R: %ld %lu %lu %ld (%ld)\n", R_s, R_f1, R_f0, R_e, R_c); #endif - return __FP_PACK_D(frD, R); + if (R_c == FP_CLS_NAN) { + R_e = _FP_EXPMAX_D; + _FP_PACK_RAW_2_P(D, frD, R); + } else { + __FP_PACK_D(frD, R); + } + + return 0; } diff --git a/arch/powerpc/math-emu/math.c b/arch/powerpc/math-emu/math.c index 29e545e0272..164d55935bd 100644 --- a/arch/powerpc/math-emu/math.c +++ b/arch/powerpc/math-emu/math.c @@ -8,8 +8,8 @@ #include #include -#include "sfp-machine.h" -#include "double.h" +#include +#include #define FLOATFUNC(x) extern int x(void *, void *, void *, void *) @@ -168,6 +168,8 @@ record_exception(struct pt_regs *regs, int eflag) fpscr |= FPSCR_ZX; if (eflag & EFLAG_INEXACT) fpscr |= FPSCR_XX; + if (eflag & EFLAG_INVALID) + fpscr |= FPSCR_VX; if (eflag & EFLAG_VXSNAN) fpscr |= FPSCR_VXSNAN; if (eflag & EFLAG_VXISI) @@ -188,7 +190,7 @@ record_exception(struct pt_regs *regs, int eflag) fpscr |= FPSCR_VXCVI; } - fpscr &= ~(FPSCR_VX); +// fpscr &= ~(FPSCR_VX); if (fpscr & (FPSCR_VXSNAN | FPSCR_VXISI | FPSCR_VXIDI | FPSCR_VXZDZ | FPSCR_VXIMZ | FPSCR_VXVC | FPSCR_VXSOFT | FPSCR_VXSQRT | FPSCR_VXCVI)) diff --git a/arch/powerpc/math-emu/mcrfs.c b/arch/powerpc/math-emu/mcrfs.c index 41ba247faf8..e948d5708e2 100644 --- a/arch/powerpc/math-emu/mcrfs.c +++ b/arch/powerpc/math-emu/mcrfs.c @@ -2,7 +2,8 @@ #include #include -#include "soft-fp.h" +#include +#include int mcrfs(u32 *ccr, u32 crfD, u32 crfS) diff --git a/arch/powerpc/math-emu/mffs.c b/arch/powerpc/math-emu/mffs.c index b0e2106e6eb..5526cf96ede 100644 --- a/arch/powerpc/math-emu/mffs.c +++ b/arch/powerpc/math-emu/mffs.c @@ -2,7 +2,8 @@ #include #include -#include "soft-fp.h" +#include +#include int mffs(u32 *frD) diff --git a/arch/powerpc/math-emu/mtfsb0.c b/arch/powerpc/math-emu/mtfsb0.c index d3062350ea2..bc985585bca 100644 --- a/arch/powerpc/math-emu/mtfsb0.c +++ b/arch/powerpc/math-emu/mtfsb0.c @@ -2,7 +2,8 @@ #include #include -#include "soft-fp.h" +#include +#include int mtfsb0(int crbD) diff --git a/arch/powerpc/math-emu/mtfsb1.c b/arch/powerpc/math-emu/mtfsb1.c index 2e948704b56..fe6ed5ac85b 100644 --- a/arch/powerpc/math-emu/mtfsb1.c +++ b/arch/powerpc/math-emu/mtfsb1.c @@ -2,7 +2,8 @@ #include #include -#include "soft-fp.h" +#include +#include int mtfsb1(int crbD) diff --git a/arch/powerpc/math-emu/mtfsf.c b/arch/powerpc/math-emu/mtfsf.c index 48014d8e3af..dbce92e4f04 100644 --- a/arch/powerpc/math-emu/mtfsf.c +++ b/arch/powerpc/math-emu/mtfsf.c @@ -2,12 +2,14 @@ #include #include -#include "soft-fp.h" +#include +#include int mtfsf(unsigned int FM, u32 *frB) { u32 mask; + u32 fpscr; if (FM == 0) return 0; @@ -37,6 +39,22 @@ mtfsf(unsigned int FM, u32 *frB) __FPU_FPSCR &= ~(mask); __FPU_FPSCR |= (frB[1] & mask); + __FPU_FPSCR &= ~(FPSCR_VX); + if (__FPU_FPSCR & (FPSCR_VXSNAN | FPSCR_VXISI | FPSCR_VXIDI | + FPSCR_VXZDZ | FPSCR_VXIMZ | FPSCR_VXVC | + FPSCR_VXSOFT | FPSCR_VXSQRT | FPSCR_VXCVI)) + __FPU_FPSCR |= FPSCR_VX; + + fpscr = __FPU_FPSCR; + fpscr &= ~(FPSCR_FEX); + if (((fpscr & FPSCR_VX) && (fpscr & FPSCR_VE)) || + ((fpscr & FPSCR_OX) && (fpscr & FPSCR_OE)) || + ((fpscr & FPSCR_UX) && (fpscr & FPSCR_UE)) || + ((fpscr & FPSCR_ZX) && (fpscr & FPSCR_ZE)) || + ((fpscr & FPSCR_XX) && (fpscr & FPSCR_XE))) + fpscr |= FPSCR_FEX; + __FPU_FPSCR = fpscr; + #ifdef DEBUG printk("%s: %02x %p: %08lx\n", __func__, FM, frB, __FPU_FPSCR); #endif diff --git a/arch/powerpc/math-emu/mtfsfi.c b/arch/powerpc/math-emu/mtfsfi.c index 031e2009354..fd2acc26813 100644 --- a/arch/powerpc/math-emu/mtfsfi.c +++ b/arch/powerpc/math-emu/mtfsfi.c @@ -2,7 +2,8 @@ #include #include -#include "soft-fp.h" +#include +#include int mtfsfi(unsigned int crfD, unsigned int IMM) diff --git a/arch/powerpc/math-emu/op-1.h b/arch/powerpc/math-emu/op-1.h deleted file mode 100644 index c92fa95f562..00000000000 --- a/arch/powerpc/math-emu/op-1.h +++ /dev/null @@ -1,245 +0,0 @@ -/* - * Basic one-word fraction declaration and manipulation. - */ - -#define _FP_FRAC_DECL_1(X) _FP_W_TYPE X##_f -#define _FP_FRAC_COPY_1(D,S) (D##_f = S##_f) -#define _FP_FRAC_SET_1(X,I) (X##_f = I) -#define _FP_FRAC_HIGH_1(X) (X##_f) -#define _FP_FRAC_LOW_1(X) (X##_f) -#define _FP_FRAC_WORD_1(X,w) (X##_f) - -#define _FP_FRAC_ADDI_1(X,I) (X##_f += I) -#define _FP_FRAC_SLL_1(X,N) \ - do { \ - if (__builtin_constant_p(N) && (N) == 1) \ - X##_f += X##_f; \ - else \ - X##_f <<= (N); \ - } while (0) -#define _FP_FRAC_SRL_1(X,N) (X##_f >>= N) - -/* Right shift with sticky-lsb. */ -#define _FP_FRAC_SRS_1(X,N,sz) __FP_FRAC_SRS_1(X##_f, N, sz) - -#define __FP_FRAC_SRS_1(X,N,sz) \ - (X = (X >> (N) | (__builtin_constant_p(N) && (N) == 1 \ - ? X & 1 : (X << (_FP_W_TYPE_SIZE - (N))) != 0))) - -#define _FP_FRAC_ADD_1(R,X,Y) (R##_f = X##_f + Y##_f) -#define _FP_FRAC_SUB_1(R,X,Y) (R##_f = X##_f - Y##_f) -#define _FP_FRAC_CLZ_1(z, X) __FP_CLZ(z, X##_f) - -/* Predicates */ -#define _FP_FRAC_NEGP_1(X) ((_FP_WS_TYPE)X##_f < 0) -#define _FP_FRAC_ZEROP_1(X) (X##_f == 0) -#define _FP_FRAC_OVERP_1(fs,X) (X##_f & _FP_OVERFLOW_##fs) -#define _FP_FRAC_EQ_1(X, Y) (X##_f == Y##_f) -#define _FP_FRAC_GE_1(X, Y) (X##_f >= Y##_f) -#define _FP_FRAC_GT_1(X, Y) (X##_f > Y##_f) - -#define _FP_ZEROFRAC_1 0 -#define _FP_MINFRAC_1 1 - -/* - * Unpack the raw bits of a native fp value. Do not classify or - * normalize the data. - */ - -#define _FP_UNPACK_RAW_1(fs, X, val) \ - do { \ - union _FP_UNION_##fs _flo; _flo.flt = (val); \ - \ - X##_f = _flo.bits.frac; \ - X##_e = _flo.bits.exp; \ - X##_s = _flo.bits.sign; \ - } while (0) - - -/* - * Repack the raw bits of a native fp value. - */ - -#define _FP_PACK_RAW_1(fs, val, X) \ - do { \ - union _FP_UNION_##fs _flo; \ - \ - _flo.bits.frac = X##_f; \ - _flo.bits.exp = X##_e; \ - _flo.bits.sign = X##_s; \ - \ - (val) = _flo.flt; \ - } while (0) - - -/* - * Multiplication algorithms: - */ - -/* Basic. Assuming the host word size is >= 2*FRACBITS, we can do the - multiplication immediately. */ - -#define _FP_MUL_MEAT_1_imm(fs, R, X, Y) \ - do { \ - R##_f = X##_f * Y##_f; \ - /* Normalize since we know where the msb of the multiplicands \ - were (bit B), we know that the msb of the of the product is \ - at either 2B or 2B-1. */ \ - _FP_FRAC_SRS_1(R, _FP_WFRACBITS_##fs-1, 2*_FP_WFRACBITS_##fs); \ - } while (0) - -/* Given a 1W * 1W => 2W primitive, do the extended multiplication. */ - -#define _FP_MUL_MEAT_1_wide(fs, R, X, Y, doit) \ - do { \ - _FP_W_TYPE _Z_f0, _Z_f1; \ - doit(_Z_f1, _Z_f0, X##_f, Y##_f); \ - /* Normalize since we know where the msb of the multiplicands \ - were (bit B), we know that the msb of the of the product is \ - at either 2B or 2B-1. */ \ - _FP_FRAC_SRS_2(_Z, _FP_WFRACBITS_##fs-1, 2*_FP_WFRACBITS_##fs); \ - R##_f = _Z_f0; \ - } while (0) - -/* Finally, a simple widening multiply algorithm. What fun! */ - -#define _FP_MUL_MEAT_1_hard(fs, R, X, Y) \ - do { \ - _FP_W_TYPE _xh, _xl, _yh, _yl, _z_f0, _z_f1, _a_f0, _a_f1; \ - \ - /* split the words in half */ \ - _xh = X##_f >> (_FP_W_TYPE_SIZE/2); \ - _xl = X##_f & (((_FP_W_TYPE)1 << (_FP_W_TYPE_SIZE/2)) - 1); \ - _yh = Y##_f >> (_FP_W_TYPE_SIZE/2); \ - _yl = Y##_f & (((_FP_W_TYPE)1 << (_FP_W_TYPE_SIZE/2)) - 1); \ - \ - /* multiply the pieces */ \ - _z_f0 = _xl * _yl; \ - _a_f0 = _xh * _yl; \ - _a_f1 = _xl * _yh; \ - _z_f1 = _xh * _yh; \ - \ - /* reassemble into two full words */ \ - if ((_a_f0 += _a_f1) < _a_f1) \ - _z_f1 += (_FP_W_TYPE)1 << (_FP_W_TYPE_SIZE/2); \ - _a_f1 = _a_f0 >> (_FP_W_TYPE_SIZE/2); \ - _a_f0 = _a_f0 << (_FP_W_TYPE_SIZE/2); \ - _FP_FRAC_ADD_2(_z, _z, _a); \ - \ - /* normalize */ \ - _FP_FRAC_SRS_2(_z, _FP_WFRACBITS_##fs - 1, 2*_FP_WFRACBITS_##fs); \ - R##_f = _z_f0; \ - } while (0) - - -/* - * Division algorithms: - */ - -/* Basic. Assuming the host word size is >= 2*FRACBITS, we can do the - division immediately. Give this macro either _FP_DIV_HELP_imm for - C primitives or _FP_DIV_HELP_ldiv for the ISO function. Which you - choose will depend on what the compiler does with divrem4. */ - -#define _FP_DIV_MEAT_1_imm(fs, R, X, Y, doit) \ - do { \ - _FP_W_TYPE _q, _r; \ - X##_f <<= (X##_f < Y##_f \ - ? R##_e--, _FP_WFRACBITS_##fs \ - : _FP_WFRACBITS_##fs - 1); \ - doit(_q, _r, X##_f, Y##_f); \ - R##_f = _q | (_r != 0); \ - } while (0) - -/* GCC's longlong.h defines a 2W / 1W => (1W,1W) primitive udiv_qrnnd - that may be useful in this situation. This first is for a primitive - that requires normalization, the second for one that does not. Look - for UDIV_NEEDS_NORMALIZATION to tell which your machine needs. */ - -#define _FP_DIV_MEAT_1_udiv_norm(fs, R, X, Y) \ - do { \ - _FP_W_TYPE _nh, _nl, _q, _r; \ - \ - /* Normalize Y -- i.e. make the most significant bit set. */ \ - Y##_f <<= _FP_WFRACXBITS_##fs - 1; \ - \ - /* Shift X op correspondingly high, that is, up one full word. */ \ - if (X##_f <= Y##_f) \ - { \ - _nl = 0; \ - _nh = X##_f; \ - } \ - else \ - { \ - R##_e++; \ - _nl = X##_f << (_FP_W_TYPE_SIZE-1); \ - _nh = X##_f >> 1; \ - } \ - \ - udiv_qrnnd(_q, _r, _nh, _nl, Y##_f); \ - R##_f = _q | (_r != 0); \ - } while (0) - -#define _FP_DIV_MEAT_1_udiv(fs, R, X, Y) \ - do { \ - _FP_W_TYPE _nh, _nl, _q, _r; \ - if (X##_f < Y##_f) \ - { \ - R##_e--; \ - _nl = X##_f << _FP_WFRACBITS_##fs; \ - _nh = X##_f >> _FP_WFRACXBITS_##fs; \ - } \ - else \ - { \ - _nl = X##_f << (_FP_WFRACBITS_##fs - 1); \ - _nh = X##_f >> (_FP_WFRACXBITS_##fs + 1); \ - } \ - udiv_qrnnd(_q, _r, _nh, _nl, Y##_f); \ - R##_f = _q | (_r != 0); \ - } while (0) - - -/* - * Square root algorithms: - * We have just one right now, maybe Newton approximation - * should be added for those machines where division is fast. - */ - -#define _FP_SQRT_MEAT_1(R, S, T, X, q) \ - do { \ - while (q) \ - { \ - T##_f = S##_f + q; \ - if (T##_f <= X##_f) \ - { \ - S##_f = T##_f + q; \ - X##_f -= T##_f; \ - R##_f += q; \ - } \ - _FP_FRAC_SLL_1(X, 1); \ - q >>= 1; \ - } \ - } while (0) - -/* - * Assembly/disassembly for converting to/from integral types. - * No shifting or overflow handled here. - */ - -#define _FP_FRAC_ASSEMBLE_1(r, X, rsize) (r = X##_f) -#define _FP_FRAC_DISASSEMBLE_1(X, r, rsize) (X##_f = r) - - -/* - * Convert FP values between word sizes - */ - -#define _FP_FRAC_CONV_1_1(dfs, sfs, D, S) \ - do { \ - D##_f = S##_f; \ - if (_FP_WFRACBITS_##sfs > _FP_WFRACBITS_##dfs) \ - _FP_FRAC_SRS_1(D, (_FP_WFRACBITS_##sfs-_FP_WFRACBITS_##dfs), \ - _FP_WFRACBITS_##sfs); \ - else \ - D##_f <<= _FP_WFRACBITS_##dfs - _FP_WFRACBITS_##sfs; \ - } while (0) diff --git a/arch/powerpc/math-emu/op-2.h b/arch/powerpc/math-emu/op-2.h deleted file mode 100644 index 7d6f17cc292..00000000000 --- a/arch/powerpc/math-emu/op-2.h +++ /dev/null @@ -1,434 +0,0 @@ -/* - * Basic two-word fraction declaration and manipulation. - */ - -#define _FP_FRAC_DECL_2(X) _FP_W_TYPE X##_f0, X##_f1 -#define _FP_FRAC_COPY_2(D,S) (D##_f0 = S##_f0, D##_f1 = S##_f1) -#define _FP_FRAC_SET_2(X,I) __FP_FRAC_SET_2(X, I) -#define _FP_FRAC_HIGH_2(X) (X##_f1) -#define _FP_FRAC_LOW_2(X) (X##_f0) -#define _FP_FRAC_WORD_2(X,w) (X##_f##w) - -#define _FP_FRAC_SLL_2(X,N) \ - do { \ - if ((N) < _FP_W_TYPE_SIZE) \ - { \ - if (__builtin_constant_p(N) && (N) == 1) \ - { \ - X##_f1 = X##_f1 + X##_f1 + (((_FP_WS_TYPE)(X##_f0)) < 0); \ - X##_f0 += X##_f0; \ - } \ - else \ - { \ - X##_f1 = X##_f1 << (N) | X##_f0 >> (_FP_W_TYPE_SIZE - (N)); \ - X##_f0 <<= (N); \ - } \ - } \ - else \ - { \ - X##_f1 = X##_f0 << ((N) - _FP_W_TYPE_SIZE); \ - X##_f0 = 0; \ - } \ - } while (0) - -#define _FP_FRAC_SRL_2(X,N) \ - do { \ - if ((N) < _FP_W_TYPE_SIZE) \ - { \ - X##_f0 = X##_f0 >> (N) | X##_f1 << (_FP_W_TYPE_SIZE - (N)); \ - X##_f1 >>= (N); \ - } \ - else \ - { \ - X##_f0 = X##_f1 >> ((N) - _FP_W_TYPE_SIZE); \ - X##_f1 = 0; \ - } \ - } while (0) - -/* Right shift with sticky-lsb. */ -#define _FP_FRAC_SRS_2(X,N,sz) \ - do { \ - if ((N) < _FP_W_TYPE_SIZE) \ - { \ - X##_f0 = (X##_f1 << (_FP_W_TYPE_SIZE - (N)) | X##_f0 >> (N) | \ - (__builtin_constant_p(N) && (N) == 1 \ - ? X##_f0 & 1 \ - : (X##_f0 << (_FP_W_TYPE_SIZE - (N))) != 0)); \ - X##_f1 >>= (N); \ - } \ - else \ - { \ - X##_f0 = (X##_f1 >> ((N) - _FP_W_TYPE_SIZE) | \ - (((X##_f1 << (2 * _FP_W_TYPE_SIZE - (N))) | \ - X##_f0) != 0)); \ - X##_f1 = 0; \ - } \ - } while (0) - -#define _FP_FRAC_ADDI_2(X,I) \ - __FP_FRAC_ADDI_2(X##_f1, X##_f0, I) - -#define _FP_FRAC_ADD_2(R,X,Y) \ - __FP_FRAC_ADD_2(R##_f1, R##_f0, X##_f1, X##_f0, Y##_f1, Y##_f0) - -#define _FP_FRAC_SUB_2(R,X,Y) \ - __FP_FRAC_SUB_2(R##_f1, R##_f0, X##_f1, X##_f0, Y##_f1, Y##_f0) - -#define _FP_FRAC_CLZ_2(R,X) \ - do { \ - if (X##_f1) \ - __FP_CLZ(R,X##_f1); \ - else \ - { \ - __FP_CLZ(R,X##_f0); \ - R += _FP_W_TYPE_SIZE; \ - } \ - } while(0) - -/* Predicates */ -#define _FP_FRAC_NEGP_2(X) ((_FP_WS_TYPE)X##_f1 < 0) -#define _FP_FRAC_ZEROP_2(X) ((X##_f1 | X##_f0) == 0) -#define _FP_FRAC_OVERP_2(fs,X) (X##_f1 & _FP_OVERFLOW_##fs) -#define _FP_FRAC_EQ_2(X, Y) (X##_f1 == Y##_f1 && X##_f0 == Y##_f0) -#define _FP_FRAC_GT_2(X, Y) \ - ((X##_f1 > Y##_f1) || (X##_f1 == Y##_f1 && X##_f0 > Y##_f0)) -#define _FP_FRAC_GE_2(X, Y) \ - ((X##_f1 > Y##_f1) || (X##_f1 == Y##_f1 && X##_f0 >= Y##_f0)) - -#define _FP_ZEROFRAC_2 0, 0 -#define _FP_MINFRAC_2 0, 1 - -/* - * Internals - */ - -#define __FP_FRAC_SET_2(X,I1,I0) (X##_f0 = I0, X##_f1 = I1) - -#define __FP_CLZ_2(R, xh, xl) \ - do { \ - if (xh) \ - __FP_CLZ(R,xl); \ - else \ - { \ - __FP_CLZ(R,xl); \ - R += _FP_W_TYPE_SIZE; \ - } \ - } while(0) - -#if 0 - -#ifndef __FP_FRAC_ADDI_2 -#define __FP_FRAC_ADDI_2(xh, xl, i) \ - (xh += ((xl += i) < i)) -#endif -#ifndef __FP_FRAC_ADD_2 -#define __FP_FRAC_ADD_2(rh, rl, xh, xl, yh, yl) \ - (rh = xh + yh + ((rl = xl + yl) < xl)) -#endif -#ifndef __FP_FRAC_SUB_2 -#define __FP_FRAC_SUB_2(rh, rl, xh, xl, yh, yl) \ - (rh = xh - yh - ((rl = xl - yl) > xl)) -#endif - -#else - -#undef __FP_FRAC_ADDI_2 -#define __FP_FRAC_ADDI_2(xh, xl, i) add_ssaaaa(xh, xl, xh, xl, 0, i) -#undef __FP_FRAC_ADD_2 -#define __FP_FRAC_ADD_2 add_ssaaaa -#undef __FP_FRAC_SUB_2 -#define __FP_FRAC_SUB_2 sub_ddmmss - -#endif - -/* - * Unpack the raw bits of a native fp value. Do not classify or - * normalize the data. - */ - -#define _FP_UNPACK_RAW_2(fs, X, val) \ - do { \ - union _FP_UNION_##fs _flo; _flo.flt = (val); \ - \ - X##_f0 = _flo.bits.frac0; \ - X##_f1 = _flo.bits.frac1; \ - X##_e = _flo.bits.exp; \ - X##_s = _flo.bits.sign; \ - } while (0) - - -/* - * Repack the raw bits of a native fp value. - */ - -#define _FP_PACK_RAW_2(fs, val, X) \ - do { \ - union _FP_UNION_##fs _flo; \ - \ - _flo.bits.frac0 = X##_f0; \ - _flo.bits.frac1 = X##_f1; \ - _flo.bits.exp = X##_e; \ - _flo.bits.sign = X##_s; \ - \ - (val) = _flo.flt; \ - } while (0) - - -/* - * Multiplication algorithms: - */ - -/* Given a 1W * 1W => 2W primitive, do the extended multiplication. */ - -#define _FP_MUL_MEAT_2_wide(fs, R, X, Y, doit) \ - do { \ - _FP_FRAC_DECL_4(_z); _FP_FRAC_DECL_2(_b); _FP_FRAC_DECL_2(_c); \ - \ - doit(_FP_FRAC_WORD_4(_z,1), _FP_FRAC_WORD_4(_z,0), X##_f0, Y##_f0); \ - doit(_b_f1, _b_f0, X##_f0, Y##_f1); \ - doit(_c_f1, _c_f0, X##_f1, Y##_f0); \ - doit(_FP_FRAC_WORD_4(_z,3), _FP_FRAC_WORD_4(_z,2), X##_f1, Y##_f1); \ - \ - __FP_FRAC_ADD_4(_FP_FRAC_WORD_4(_z,3),_FP_FRAC_WORD_4(_z,2), \ - _FP_FRAC_WORD_4(_z,1),_FP_FRAC_WORD_4(_z,0), \ - 0, _b_f1, _b_f0, 0, \ - _FP_FRAC_WORD_4(_z,3),_FP_FRAC_WORD_4(_z,2), \ - _FP_FRAC_WORD_4(_z,1),_FP_FRAC_WORD_4(_z,0)); \ - __FP_FRAC_ADD_4(_FP_FRAC_WORD_4(_z,3),_FP_FRAC_WORD_4(_z,2), \ - _FP_FRAC_WORD_4(_z,1),_FP_FRAC_WORD_4(_z,0), \ - 0, _c_f1, _c_f0, 0, \ - _FP_FRAC_WORD_4(_z,3),_FP_FRAC_WORD_4(_z,2), \ - _FP_FRAC_WORD_4(_z,1),_FP_FRAC_WORD_4(_z,0)); \ - \ - /* Normalize since we know where the msb of the multiplicands \ - were (bit B), we know that the msb of the of the product is \ - at either 2B or 2B-1. */ \ - _FP_FRAC_SRS_4(_z, _FP_WFRACBITS_##fs-1, 2*_FP_WFRACBITS_##fs); \ - R##_f0 = _FP_FRAC_WORD_4(_z,0); \ - R##_f1 = _FP_FRAC_WORD_4(_z,1); \ - } while (0) - -/* This next macro appears to be totally broken. Fortunately nowhere - * seems to use it :-> The problem is that we define _z[4] but - * then use it in _FP_FRAC_SRS_4, which will attempt to access - * _z_f[n] which will cause an error. The fix probably involves - * declaring it with _FP_FRAC_DECL_4, see previous macro. -- PMM 02/1998 - */ -#define _FP_MUL_MEAT_2_gmp(fs, R, X, Y) \ - do { \ - _FP_W_TYPE _x[2], _y[2], _z[4]; \ - _x[0] = X##_f0; _x[1] = X##_f1; \ - _y[0] = Y##_f0; _y[1] = Y##_f1; \ - \ - mpn_mul_n(_z, _x, _y, 2); \ - \ - /* Normalize since we know where the msb of the multiplicands \ - were (bit B), we know that the msb of the of the product is \ - at either 2B or 2B-1. */ \ - _FP_FRAC_SRS_4(_z, _FP_WFRACBITS##_fs-1, 2*_FP_WFRACBITS_##fs); \ - R##_f0 = _z[0]; \ - R##_f1 = _z[1]; \ - } while (0) - - -/* - * Division algorithms: - * This seems to be giving me difficulties -- PMM - * Look, NetBSD seems to be able to comment algorithms. Can't you? - * I've thrown printks at the problem. - * This now appears to work, but I still don't really know why. - * Also, I don't think the result is properly normalised... - */ - -#define _FP_DIV_MEAT_2_udiv_64(fs, R, X, Y) \ - do { \ - extern void _fp_udivmodti4(_FP_W_TYPE q[2], _FP_W_TYPE r[2], \ - _FP_W_TYPE n1, _FP_W_TYPE n0, \ - _FP_W_TYPE d1, _FP_W_TYPE d0); \ - _FP_W_TYPE _n_f3, _n_f2, _n_f1, _n_f0, _r_f1, _r_f0; \ - _FP_W_TYPE _q_f1, _q_f0, _m_f1, _m_f0; \ - _FP_W_TYPE _rmem[2], _qmem[2]; \ - /* I think this check is to ensure that the result is normalised. \ - * Assuming X,Y normalised (ie in [1.0,2.0)) X/Y will be in \ - * [0.5,2.0). Furthermore, it will be less than 1.0 iff X < Y. \ - * In this case we tweak things. (this is based on comments in \ - * the NetBSD FPU emulation code. ) \ - * We know X,Y are normalised because we ensure this as part of \ - * the unpacking process. -- PMM \ - */ \ - if (_FP_FRAC_GT_2(X, Y)) \ - { \ -/* R##_e++; */ \ - _n_f3 = X##_f1 >> 1; \ - _n_f2 = X##_f1 << (_FP_W_TYPE_SIZE - 1) | X##_f0 >> 1; \ - _n_f1 = X##_f0 << (_FP_W_TYPE_SIZE - 1); \ - _n_f0 = 0; \ - } \ - else \ - { \ - R##_e--; \ - _n_f3 = X##_f1; \ - _n_f2 = X##_f0; \ - _n_f1 = _n_f0 = 0; \ - } \ - \ - /* Normalize, i.e. make the most significant bit of the \ - denominator set. CHANGED: - 1 to nothing -- PMM */ \ - _FP_FRAC_SLL_2(Y, _FP_WFRACXBITS_##fs /* -1 */); \ - \ - /* Do the 256/128 bit division given the 128-bit _fp_udivmodtf4 \ - primitive snagged from libgcc2.c. */ \ - \ - _fp_udivmodti4(_qmem, _rmem, _n_f3, _n_f2, 0, Y##_f1); \ - _q_f1 = _qmem[0]; \ - umul_ppmm(_m_f1, _m_f0, _q_f1, Y##_f0); \ - _r_f1 = _rmem[0]; \ - _r_f0 = _n_f1; \ - if (_FP_FRAC_GT_2(_m, _r)) \ - { \ - _q_f1--; \ - _FP_FRAC_ADD_2(_r, _r, Y); \ - if (_FP_FRAC_GE_2(_r, Y) && _FP_FRAC_GT_2(_m, _r)) \ - { \ - _q_f1--; \ - _FP_FRAC_ADD_2(_r, _r, Y); \ - } \ - } \ - _FP_FRAC_SUB_2(_r, _r, _m); \ - \ - _fp_udivmodti4(_qmem, _rmem, _r_f1, _r_f0, 0, Y##_f1); \ - _q_f0 = _qmem[0]; \ - umul_ppmm(_m_f1, _m_f0, _q_f0, Y##_f0); \ - _r_f1 = _rmem[0]; \ - _r_f0 = _n_f0; \ - if (_FP_FRAC_GT_2(_m, _r)) \ - { \ - _q_f0--; \ - _FP_FRAC_ADD_2(_r, _r, Y); \ - if (_FP_FRAC_GE_2(_r, Y) && _FP_FRAC_GT_2(_m, _r)) \ - { \ - _q_f0--; \ - _FP_FRAC_ADD_2(_r, _r, Y); \ - } \ - } \ - _FP_FRAC_SUB_2(_r, _r, _m); \ - \ - R##_f1 = _q_f1; \ - R##_f0 = _q_f0 | ((_r_f1 | _r_f0) != 0); \ - /* adjust so answer is normalized again. I'm not sure what the \ - * final sz param should be. In practice it's never used since \ - * N is 1 which is always going to be < _FP_W_TYPE_SIZE... \ - */ \ - /* _FP_FRAC_SRS_2(R,1,_FP_WFRACBITS_##fs); */ \ - } while (0) - - -#define _FP_DIV_MEAT_2_gmp(fs, R, X, Y) \ - do { \ - _FP_W_TYPE _x[4], _y[2], _z[4]; \ - _y[0] = Y##_f0; _y[1] = Y##_f1; \ - _x[0] = _x[3] = 0; \ - if (_FP_FRAC_GT_2(X, Y)) \ - { \ - R##_e++; \ - _x[1] = (X##_f0 << (_FP_WFRACBITS-1 - _FP_W_TYPE_SIZE) | \ - X##_f1 >> (_FP_W_TYPE_SIZE - \ - (_FP_WFRACBITS-1 - _FP_W_TYPE_SIZE))); \ - _x[2] = X##_f1 << (_FP_WFRACBITS-1 - _FP_W_TYPE_SIZE); \ - } \ - else \ - { \ - _x[1] = (X##_f0 << (_FP_WFRACBITS - _FP_W_TYPE_SIZE) | \ - X##_f1 >> (_FP_W_TYPE_SIZE - \ - (_FP_WFRACBITS - _FP_W_TYPE_SIZE))); \ - _x[2] = X##_f1 << (_FP_WFRACBITS - _FP_W_TYPE_SIZE); \ - } \ - \ - (void) mpn_divrem (_z, 0, _x, 4, _y, 2); \ - R##_f1 = _z[1]; \ - R##_f0 = _z[0] | ((_x[0] | _x[1]) != 0); \ - } while (0) - - -/* - * Square root algorithms: - * We have just one right now, maybe Newton approximation - * should be added for those machines where division is fast. - */ - -#define _FP_SQRT_MEAT_2(R, S, T, X, q) \ - do { \ - while (q) \ - { \ - T##_f1 = S##_f1 + q; \ - if (T##_f1 <= X##_f1) \ - { \ - S##_f1 = T##_f1 + q; \ - X##_f1 -= T##_f1; \ - R##_f1 += q; \ - } \ - _FP_FRAC_SLL_2(X, 1); \ - q >>= 1; \ - } \ - q = (_FP_W_TYPE)1 << (_FP_W_TYPE_SIZE - 1); \ - while (q) \ - { \ - T##_f0 = S##_f0 + q; \ - T##_f1 = S##_f1; \ - if (T##_f1 < X##_f1 || \ - (T##_f1 == X##_f1 && T##_f0 < X##_f0)) \ - { \ - S##_f0 = T##_f0 + q; \ - if (((_FP_WS_TYPE)T##_f0) < 0 && \ - ((_FP_WS_TYPE)S##_f0) >= 0) \ - S##_f1++; \ - _FP_FRAC_SUB_2(X, X, T); \ - R##_f0 += q; \ - } \ - _FP_FRAC_SLL_2(X, 1); \ - q >>= 1; \ - } \ - } while (0) - - -/* - * Assembly/disassembly for converting to/from integral types. - * No shifting or overflow handled here. - */ - -#define _FP_FRAC_ASSEMBLE_2(r, X, rsize) \ - do { \ - if (rsize <= _FP_W_TYPE_SIZE) \ - r = X##_f0; \ - else \ - { \ - r = X##_f1; \ - r <<= _FP_W_TYPE_SIZE; \ - r += X##_f0; \ - } \ - } while (0) - -#define _FP_FRAC_DISASSEMBLE_2(X, r, rsize) \ - do { \ - X##_f0 = r; \ - X##_f1 = (rsize <= _FP_W_TYPE_SIZE ? 0 : r >> _FP_W_TYPE_SIZE); \ - } while (0) - -/* - * Convert FP values between word sizes - */ - -#define _FP_FRAC_CONV_1_2(dfs, sfs, D, S) \ - do { \ - _FP_FRAC_SRS_2(S, (_FP_WFRACBITS_##sfs - _FP_WFRACBITS_##dfs), \ - _FP_WFRACBITS_##sfs); \ - D##_f = S##_f0; \ - } while (0) - -#define _FP_FRAC_CONV_2_1(dfs, sfs, D, S) \ - do { \ - D##_f0 = S##_f; \ - D##_f1 = 0; \ - _FP_FRAC_SLL_2(D, (_FP_WFRACBITS_##dfs - _FP_WFRACBITS_##sfs)); \ - } while (0) - diff --git a/arch/powerpc/math-emu/op-4.h b/arch/powerpc/math-emu/op-4.h deleted file mode 100644 index c9ae626070d..00000000000 --- a/arch/powerpc/math-emu/op-4.h +++ /dev/null @@ -1,317 +0,0 @@ -/* - * Basic four-word fraction declaration and manipulation. - * - * When adding quadword support for 32 bit machines, we need - * to be a little careful as double multiply uses some of these - * macros: (in op-2.h) - * _FP_MUL_MEAT_2_wide() uses _FP_FRAC_DECL_4, _FP_FRAC_WORD_4, - * _FP_FRAC_ADD_4, _FP_FRAC_SRS_4 - * _FP_MUL_MEAT_2_gmp() uses _FP_FRAC_SRS_4 (and should use - * _FP_FRAC_DECL_4: it appears to be broken and is not used - * anywhere anyway. ) - * - * I've now fixed all the macros that were here from the sparc64 code. - * [*none* of the shift macros were correct!] -- PMM 02/1998 - * - * The only quadword stuff that remains to be coded is: - * 1) the conversion to/from ints, which requires - * that we check (in op-common.h) that the following do the right thing - * for quadwords: _FP_TO_INT(Q,4,r,X,rsz,rsg), _FP_FROM_INT(Q,4,X,r,rs,rt) - * 2) multiply, divide and sqrt, which require: - * _FP_MUL_MEAT_4_*(R,X,Y), _FP_DIV_MEAT_4_*(R,X,Y), _FP_SQRT_MEAT_4(R,S,T,X,q), - * This also needs _FP_MUL_MEAT_Q and _FP_DIV_MEAT_Q to be defined to - * some suitable _FP_MUL_MEAT_4_* macros in sfp-machine.h. - * [we're free to choose whatever FP_MUL_MEAT_4_* macros we need for - * these; they are used nowhere else. ] - */ - -#define _FP_FRAC_DECL_4(X) _FP_W_TYPE X##_f[4] -#define _FP_FRAC_COPY_4(D,S) \ - (D##_f[0] = S##_f[0], D##_f[1] = S##_f[1], \ - D##_f[2] = S##_f[2], D##_f[3] = S##_f[3]) -/* The _FP_FRAC_SET_n(X,I) macro is intended for use with another - * macro such as _FP_ZEROFRAC_n which returns n comma separated values. - * The result is that we get an expansion of __FP_FRAC_SET_n(X,I0,I1,I2,I3) - * which just assigns the In values to the array X##_f[]. - * This is why the number of parameters doesn't appear to match - * at first glance... -- PMM - */ -#define _FP_FRAC_SET_4(X,I) __FP_FRAC_SET_4(X, I) -#define _FP_FRAC_HIGH_4(X) (X##_f[3]) -#define _FP_FRAC_LOW_4(X) (X##_f[0]) -#define _FP_FRAC_WORD_4(X,w) (X##_f[w]) - -#define _FP_FRAC_SLL_4(X,N) \ - do { \ - _FP_I_TYPE _up, _down, _skip, _i; \ - _skip = (N) / _FP_W_TYPE_SIZE; \ - _up = (N) % _FP_W_TYPE_SIZE; \ - _down = _FP_W_TYPE_SIZE - _up; \ - for (_i = 3; _i > _skip; --_i) \ - X##_f[_i] = X##_f[_i-_skip] << _up | X##_f[_i-_skip-1] >> _down; \ -/* bugfixed: was X##_f[_i] <<= _up; -- PMM 02/1998 */ \ - X##_f[_i] = X##_f[0] << _up; \ - for (--_i; _i >= 0; --_i) \ - X##_f[_i] = 0; \ - } while (0) - -/* This one was broken too */ -#define _FP_FRAC_SRL_4(X,N) \ - do { \ - _FP_I_TYPE _up, _down, _skip, _i; \ - _skip = (N) / _FP_W_TYPE_SIZE; \ - _down = (N) % _FP_W_TYPE_SIZE; \ - _up = _FP_W_TYPE_SIZE - _down; \ - for (_i = 0; _i < 3-_skip; ++_i) \ - X##_f[_i] = X##_f[_i+_skip] >> _down | X##_f[_i+_skip+1] << _up; \ - X##_f[_i] = X##_f[3] >> _down; \ - for (++_i; _i < 4; ++_i) \ - X##_f[_i] = 0; \ - } while (0) - - -/* Right shift with sticky-lsb. - * What this actually means is that we do a standard right-shift, - * but that if any of the bits that fall off the right hand side - * were one then we always set the LSbit. - */ -#define _FP_FRAC_SRS_4(X,N,size) \ - do { \ - _FP_I_TYPE _up, _down, _skip, _i; \ - _FP_W_TYPE _s; \ - _skip = (N) / _FP_W_TYPE_SIZE; \ - _down = (N) % _FP_W_TYPE_SIZE; \ - _up = _FP_W_TYPE_SIZE - _down; \ - for (_s = _i = 0; _i < _skip; ++_i) \ - _s |= X##_f[_i]; \ - _s |= X##_f[_i] << _up; \ -/* s is now != 0 if we want to set the LSbit */ \ - for (_i = 0; _i < 3-_skip; ++_i) \ - X##_f[_i] = X##_f[_i+_skip] >> _down | X##_f[_i+_skip+1] << _up; \ - X##_f[_i] = X##_f[3] >> _down; \ - for (++_i; _i < 4; ++_i) \ - X##_f[_i] = 0; \ - /* don't fix the LSB until the very end when we're sure f[0] is stable */ \ - X##_f[0] |= (_s != 0); \ - } while (0) - -#define _FP_FRAC_ADD_4(R,X,Y) \ - __FP_FRAC_ADD_4(R##_f[3], R##_f[2], R##_f[1], R##_f[0], \ - X##_f[3], X##_f[2], X##_f[1], X##_f[0], \ - Y##_f[3], Y##_f[2], Y##_f[1], Y##_f[0]) - -#define _FP_FRAC_SUB_4(R,X,Y) \ - __FP_FRAC_SUB_4(R##_f[3], R##_f[2], R##_f[1], R##_f[0], \ - X##_f[3], X##_f[2], X##_f[1], X##_f[0], \ - Y##_f[3], Y##_f[2], Y##_f[1], Y##_f[0]) - -#define _FP_FRAC_ADDI_4(X,I) \ - __FP_FRAC_ADDI_4(X##_f[3], X##_f[2], X##_f[1], X##_f[0], I) - -#define _FP_ZEROFRAC_4 0,0,0,0 -#define _FP_MINFRAC_4 0,0,0,1 - -#define _FP_FRAC_ZEROP_4(X) ((X##_f[0] | X##_f[1] | X##_f[2] | X##_f[3]) == 0) -#define _FP_FRAC_NEGP_4(X) ((_FP_WS_TYPE)X##_f[3] < 0) -#define _FP_FRAC_OVERP_4(fs,X) (X##_f[0] & _FP_OVERFLOW_##fs) - -#define _FP_FRAC_EQ_4(X,Y) \ - (X##_f[0] == Y##_f[0] && X##_f[1] == Y##_f[1] \ - && X##_f[2] == Y##_f[2] && X##_f[3] == Y##_f[3]) - -#define _FP_FRAC_GT_4(X,Y) \ - (X##_f[3] > Y##_f[3] || \ - (X##_f[3] == Y##_f[3] && (X##_f[2] > Y##_f[2] || \ - (X##_f[2] == Y##_f[2] && (X##_f[1] > Y##_f[1] || \ - (X##_f[1] == Y##_f[1] && X##_f[0] > Y##_f[0]) \ - )) \ - )) \ - ) - -#define _FP_FRAC_GE_4(X,Y) \ - (X##_f[3] > Y##_f[3] || \ - (X##_f[3] == Y##_f[3] && (X##_f[2] > Y##_f[2] || \ - (X##_f[2] == Y##_f[2] && (X##_f[1] > Y##_f[1] || \ - (X##_f[1] == Y##_f[1] && X##_f[0] >= Y##_f[0]) \ - )) \ - )) \ - ) - - -#define _FP_FRAC_CLZ_4(R,X) \ - do { \ - if (X##_f[3]) \ - { \ - __FP_CLZ(R,X##_f[3]); \ - } \ - else if (X##_f[2]) \ - { \ - __FP_CLZ(R,X##_f[2]); \ - R += _FP_W_TYPE_SIZE; \ - } \ - else if (X##_f[1]) \ - { \ - __FP_CLZ(R,X##_f[2]); \ - R += _FP_W_TYPE_SIZE*2; \ - } \ - else \ - { \ - __FP_CLZ(R,X##_f[0]); \ - R += _FP_W_TYPE_SIZE*3; \ - } \ - } while(0) - - -#define _FP_UNPACK_RAW_4(fs, X, val) \ - do { \ - union _FP_UNION_##fs _flo; _flo.flt = (val); \ - X##_f[0] = _flo.bits.frac0; \ - X##_f[1] = _flo.bits.frac1; \ - X##_f[2] = _flo.bits.frac2; \ - X##_f[3] = _flo.bits.frac3; \ - X##_e = _flo.bits.exp; \ - X##_s = _flo.bits.sign; \ - } while (0) - -#define _FP_PACK_RAW_4(fs, val, X) \ - do { \ - union _FP_UNION_##fs _flo; \ - _flo.bits.frac0 = X##_f[0]; \ - _flo.bits.frac1 = X##_f[1]; \ - _flo.bits.frac2 = X##_f[2]; \ - _flo.bits.frac3 = X##_f[3]; \ - _flo.bits.exp = X##_e; \ - _flo.bits.sign = X##_s; \ - (val) = _flo.flt; \ - } while (0) - - -/* - * Internals - */ - -#define __FP_FRAC_SET_4(X,I3,I2,I1,I0) \ - (X##_f[3] = I3, X##_f[2] = I2, X##_f[1] = I1, X##_f[0] = I0) - -#ifndef __FP_FRAC_ADD_4 -#define __FP_FRAC_ADD_4(r3,r2,r1,r0,x3,x2,x1,x0,y3,y2,y1,y0) \ - do { \ - int _c1, _c2, _c3; \ - r0 = x0 + y0; \ - _c1 = r0 < x0; \ - r1 = x1 + y1; \ - _c2 = r1 < x1; \ - r1 += _c1; \ - _c2 |= r1 < _c1; \ - r2 = x2 + y2; \ - _c3 = r2 < x2; \ - r2 += _c2; \ - _c3 |= r2 < _c2; \ - r3 = x3 + y3 + _c3; \ - } while (0) -#endif - -#ifndef __FP_FRAC_SUB_4 -#define __FP_FRAC_SUB_4(r3,r2,r1,r0,x3,x2,x1,x0,y3,y2,y1,y0) \ - do { \ - int _c1, _c2, _c3; \ - r0 = x0 - y0; \ - _c1 = r0 > x0; \ - r1 = x1 - y1; \ - _c2 = r1 > x1; \ - r1 -= _c1; \ - _c2 |= r1 > _c1; \ - r2 = x2 - y2; \ - _c3 = r2 > x2; \ - r2 -= _c2; \ - _c3 |= r2 > _c2; \ - r3 = x3 - y3 - _c3; \ - } while (0) -#endif - -#ifndef __FP_FRAC_ADDI_4 -/* I always wanted to be a lisp programmer :-> */ -#define __FP_FRAC_ADDI_4(x3,x2,x1,x0,i) \ - (x3 += ((x2 += ((x1 += ((x0 += i) < x0)) < x1) < x2))) -#endif - -/* Convert FP values between word sizes. This appears to be more - * complicated than I'd have expected it to be, so these might be - * wrong... These macros are in any case somewhat bogus because they - * use information about what various FRAC_n variables look like - * internally [eg, that 2 word vars are X_f0 and x_f1]. But so do - * the ones in op-2.h and op-1.h. - */ -#define _FP_FRAC_CONV_1_4(dfs, sfs, D, S) \ - do { \ - _FP_FRAC_SRS_4(S, (_FP_WFRACBITS_##sfs - _FP_WFRACBITS_##dfs), \ - _FP_WFRACBITS_##sfs); \ - D##_f = S##_f[0]; \ - } while (0) - -#define _FP_FRAC_CONV_2_4(dfs, sfs, D, S) \ - do { \ - _FP_FRAC_SRS_4(S, (_FP_WFRACBITS_##sfs - _FP_WFRACBITS_##dfs), \ - _FP_WFRACBITS_##sfs); \ - D##_f0 = S##_f[0]; \ - D##_f1 = S##_f[1]; \ - } while (0) - -/* Assembly/disassembly for converting to/from integral types. - * No shifting or overflow handled here. - */ -/* Put the FP value X into r, which is an integer of size rsize. */ -#define _FP_FRAC_ASSEMBLE_4(r, X, rsize) \ - do { \ - if (rsize <= _FP_W_TYPE_SIZE) \ - r = X##_f[0]; \ - else if (rsize <= 2*_FP_W_TYPE_SIZE) \ - { \ - r = X##_f[1]; \ - r <<= _FP_W_TYPE_SIZE; \ - r += X##_f[0]; \ - } \ - else \ - { \ - /* I'm feeling lazy so we deal with int == 3words (implausible)*/ \ - /* and int == 4words as a single case. */ \ - r = X##_f[3]; \ - r <<= _FP_W_TYPE_SIZE; \ - r += X##_f[2]; \ - r <<= _FP_W_TYPE_SIZE; \ - r += X##_f[1]; \ - r <<= _FP_W_TYPE_SIZE; \ - r += X##_f[0]; \ - } \ - } while (0) - -/* "No disassemble Number Five!" */ -/* move an integer of size rsize into X's fractional part. We rely on - * the _f[] array consisting of words of size _FP_W_TYPE_SIZE to avoid - * having to mask the values we store into it. - */ -#define _FP_FRAC_DISASSEMBLE_4(X, r, rsize) \ - do { \ - X##_f[0] = r; \ - X##_f[1] = (rsize <= _FP_W_TYPE_SIZE ? 0 : r >> _FP_W_TYPE_SIZE); \ - X##_f[2] = (rsize <= 2*_FP_W_TYPE_SIZE ? 0 : r >> 2*_FP_W_TYPE_SIZE); \ - X##_f[3] = (rsize <= 3*_FP_W_TYPE_SIZE ? 0 : r >> 3*_FP_W_TYPE_SIZE); \ - } while (0) - -#define _FP_FRAC_CONV_4_1(dfs, sfs, D, S) \ - do { \ - D##_f[0] = S##_f; \ - D##_f[1] = D##_f[2] = D##_f[3] = 0; \ - _FP_FRAC_SLL_4(D, (_FP_WFRACBITS_##dfs - _FP_WFRACBITS_##sfs)); \ - } while (0) - -#define _FP_FRAC_CONV_4_2(dfs, sfs, D, S) \ - do { \ - D##_f[0] = S##_f0; \ - D##_f[1] = S##_f1; \ - D##_f[2] = D##_f[3] = 0; \ - _FP_FRAC_SLL_4(D, (_FP_WFRACBITS_##dfs - _FP_WFRACBITS_##sfs)); \ - } while (0) - -/* FIXME! This has to be written */ -#define _FP_SQRT_MEAT_4(R, S, T, X, q) diff --git a/arch/powerpc/math-emu/op-common.h b/arch/powerpc/math-emu/op-common.h deleted file mode 100644 index afb82b6498c..00000000000 --- a/arch/powerpc/math-emu/op-common.h +++ /dev/null @@ -1,688 +0,0 @@ -#define _FP_DECL(wc, X) \ - _FP_I_TYPE X##_c, X##_s, X##_e; \ - _FP_FRAC_DECL_##wc(X) - -/* - * Finish truely unpacking a native fp value by classifying the kind - * of fp value and normalizing both the exponent and the fraction. - */ - -#define _FP_UNPACK_CANONICAL(fs, wc, X) \ -do { \ - switch (X##_e) \ - { \ - default: \ - _FP_FRAC_HIGH_##wc(X) |= _FP_IMPLBIT_##fs; \ - _FP_FRAC_SLL_##wc(X, _FP_WORKBITS); \ - X##_e -= _FP_EXPBIAS_##fs; \ - X##_c = FP_CLS_NORMAL; \ - break; \ - \ - case 0: \ - if (_FP_FRAC_ZEROP_##wc(X)) \ - X##_c = FP_CLS_ZERO; \ - else \ - { \ - /* a denormalized number */ \ - _FP_I_TYPE _shift; \ - _FP_FRAC_CLZ_##wc(_shift, X); \ - _shift -= _FP_FRACXBITS_##fs; \ - _FP_FRAC_SLL_##wc(X, (_shift+_FP_WORKBITS)); \ - X##_e -= _FP_EXPBIAS_##fs - 1 + _shift; \ - X##_c = FP_CLS_NORMAL; \ - } \ - break; \ - \ - case _FP_EXPMAX_##fs: \ - if (_FP_FRAC_ZEROP_##wc(X)) \ - X##_c = FP_CLS_INF; \ - else \ - /* we don't differentiate between signaling and quiet nans */ \ - X##_c = FP_CLS_NAN; \ - break; \ - } \ -} while (0) - - -/* - * Before packing the bits back into the native fp result, take care - * of such mundane things as rounding and overflow. Also, for some - * kinds of fp values, the original parts may not have been fully - * extracted -- but that is ok, we can regenerate them now. - */ - -#define _FP_PACK_CANONICAL(fs, wc, X) \ -({int __ret = 0; \ - switch (X##_c) \ - { \ - case FP_CLS_NORMAL: \ - X##_e += _FP_EXPBIAS_##fs; \ - if (X##_e > 0) \ - { \ - __ret |= _FP_ROUND(wc, X); \ - if (_FP_FRAC_OVERP_##wc(fs, X)) \ - { \ - _FP_FRAC_SRL_##wc(X, (_FP_WORKBITS+1)); \ - X##_e++; \ - } \ - else \ - _FP_FRAC_SRL_##wc(X, _FP_WORKBITS); \ - if (X##_e >= _FP_EXPMAX_##fs) \ - { \ - /* overflow to infinity */ \ - X##_e = _FP_EXPMAX_##fs; \ - _FP_FRAC_SET_##wc(X, _FP_ZEROFRAC_##wc); \ - __ret |= EFLAG_OVERFLOW; \ - } \ - } \ - else \ - { \ - /* we've got a denormalized number */ \ - X##_e = -X##_e + 1; \ - if (X##_e <= _FP_WFRACBITS_##fs) \ - { \ - _FP_FRAC_SRS_##wc(X, X##_e, _FP_WFRACBITS_##fs); \ - _FP_FRAC_SLL_##wc(X, 1); \ - if (_FP_FRAC_OVERP_##wc(fs, X)) \ - { \ - X##_e = 1; \ - _FP_FRAC_SET_##wc(X, _FP_ZEROFRAC_##wc); \ - } \ - else \ - { \ - X##_e = 0; \ - _FP_FRAC_SRL_##wc(X, _FP_WORKBITS+1); \ - __ret |= EFLAG_UNDERFLOW; \ - } \ - } \ - else \ - { \ - /* underflow to zero */ \ - X##_e = 0; \ - _FP_FRAC_SET_##wc(X, _FP_ZEROFRAC_##wc); \ - __ret |= EFLAG_UNDERFLOW; \ - } \ - } \ - break; \ - \ - case FP_CLS_ZERO: \ - X##_e = 0; \ - _FP_FRAC_SET_##wc(X, _FP_ZEROFRAC_##wc); \ - break; \ - \ - case FP_CLS_INF: \ - X##_e = _FP_EXPMAX_##fs; \ - _FP_FRAC_SET_##wc(X, _FP_ZEROFRAC_##wc); \ - break; \ - \ - case FP_CLS_NAN: \ - X##_e = _FP_EXPMAX_##fs; \ - if (!_FP_KEEPNANFRACP) \ - { \ - _FP_FRAC_SET_##wc(X, _FP_NANFRAC_##fs); \ - X##_s = 0; \ - } \ - else \ - _FP_FRAC_HIGH_##wc(X) |= _FP_QNANBIT_##fs; \ - break; \ - } \ - __ret; \ -}) - - -/* - * Main addition routine. The input values should be cooked. - */ - -#define _FP_ADD(fs, wc, R, X, Y) \ -do { \ - switch (_FP_CLS_COMBINE(X##_c, Y##_c)) \ - { \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_NORMAL): \ - { \ - /* shift the smaller number so that its exponent matches the larger */ \ - _FP_I_TYPE diff = X##_e - Y##_e; \ - \ - if (diff < 0) \ - { \ - diff = -diff; \ - if (diff <= _FP_WFRACBITS_##fs) \ - _FP_FRAC_SRS_##wc(X, diff, _FP_WFRACBITS_##fs); \ - else if (!_FP_FRAC_ZEROP_##wc(X)) \ - _FP_FRAC_SET_##wc(X, _FP_MINFRAC_##wc); \ - else \ - _FP_FRAC_SET_##wc(X, _FP_ZEROFRAC_##wc); \ - R##_e = Y##_e; \ - } \ - else \ - { \ - if (diff > 0) \ - { \ - if (diff <= _FP_WFRACBITS_##fs) \ - _FP_FRAC_SRS_##wc(Y, diff, _FP_WFRACBITS_##fs); \ - else if (!_FP_FRAC_ZEROP_##wc(Y)) \ - _FP_FRAC_SET_##wc(Y, _FP_MINFRAC_##wc); \ - else \ - _FP_FRAC_SET_##wc(Y, _FP_ZEROFRAC_##wc); \ - } \ - R##_e = X##_e; \ - } \ - \ - R##_c = FP_CLS_NORMAL; \ - \ - if (X##_s == Y##_s) \ - { \ - R##_s = X##_s; \ - _FP_FRAC_ADD_##wc(R, X, Y); \ - if (_FP_FRAC_OVERP_##wc(fs, R)) \ - { \ - _FP_FRAC_SRS_##wc(R, 1, _FP_WFRACBITS_##fs); \ - R##_e++; \ - } \ - } \ - else \ - { \ - R##_s = X##_s; \ - _FP_FRAC_SUB_##wc(R, X, Y); \ - if (_FP_FRAC_ZEROP_##wc(R)) \ - { \ - /* return an exact zero */ \ - if (FP_ROUNDMODE == FP_RND_MINF) \ - R##_s |= Y##_s; \ - else \ - R##_s &= Y##_s; \ - R##_c = FP_CLS_ZERO; \ - } \ - else \ - { \ - if (_FP_FRAC_NEGP_##wc(R)) \ - { \ - _FP_FRAC_SUB_##wc(R, Y, X); \ - R##_s = Y##_s; \ - } \ - \ - /* renormalize after subtraction */ \ - _FP_FRAC_CLZ_##wc(diff, R); \ - diff -= _FP_WFRACXBITS_##fs; \ - if (diff) \ - { \ - R##_e -= diff; \ - _FP_FRAC_SLL_##wc(R, diff); \ - } \ - } \ - } \ - break; \ - } \ - \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_NAN): \ - _FP_CHOOSENAN(fs, wc, R, X, Y); \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_ZERO): \ - R##_e = X##_e; \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_NORMAL): \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_INF): \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_ZERO): \ - _FP_FRAC_COPY_##wc(R, X); \ - R##_s = X##_s; \ - R##_c = X##_c; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_NORMAL): \ - R##_e = Y##_e; \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_NAN): \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_NAN): \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_NAN): \ - _FP_FRAC_COPY_##wc(R, Y); \ - R##_s = Y##_s; \ - R##_c = Y##_c; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_INF): \ - if (X##_s != Y##_s) \ - { \ - /* +INF + -INF => NAN */ \ - _FP_FRAC_SET_##wc(R, _FP_NANFRAC_##fs); \ - R##_s = X##_s ^ Y##_s; \ - R##_c = FP_CLS_NAN; \ - break; \ - } \ - /* FALLTHRU */ \ - \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_NORMAL): \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_ZERO): \ - R##_s = X##_s; \ - R##_c = FP_CLS_INF; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_INF): \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_INF): \ - R##_s = Y##_s; \ - R##_c = FP_CLS_INF; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_ZERO): \ - /* make sure the sign is correct */ \ - if (FP_ROUNDMODE == FP_RND_MINF) \ - R##_s = X##_s | Y##_s; \ - else \ - R##_s = X##_s & Y##_s; \ - R##_c = FP_CLS_ZERO; \ - break; \ - \ - default: \ - abort(); \ - } \ -} while (0) - - -/* - * Main negation routine. FIXME -- when we care about setting exception - * bits reliably, this will not do. We should examine all of the fp classes. - */ - -#define _FP_NEG(fs, wc, R, X) \ - do { \ - _FP_FRAC_COPY_##wc(R, X); \ - R##_c = X##_c; \ - R##_e = X##_e; \ - R##_s = 1 ^ X##_s; \ - } while (0) - - -/* - * Main multiplication routine. The input values should be cooked. - */ - -#define _FP_MUL(fs, wc, R, X, Y) \ -do { \ - R##_s = X##_s ^ Y##_s; \ - switch (_FP_CLS_COMBINE(X##_c, Y##_c)) \ - { \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_NORMAL): \ - R##_c = FP_CLS_NORMAL; \ - R##_e = X##_e + Y##_e + 1; \ - \ - _FP_MUL_MEAT_##fs(R,X,Y); \ - \ - if (_FP_FRAC_OVERP_##wc(fs, R)) \ - _FP_FRAC_SRS_##wc(R, 1, _FP_WFRACBITS_##fs); \ - else \ - R##_e--; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_NAN): \ - _FP_CHOOSENAN(fs, wc, R, X, Y); \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_NORMAL): \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_INF): \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_ZERO): \ - R##_s = X##_s; \ - \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_INF): \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_NORMAL): \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_NORMAL): \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_ZERO): \ - _FP_FRAC_COPY_##wc(R, X); \ - R##_c = X##_c; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_NAN): \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_NAN): \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_NAN): \ - R##_s = Y##_s; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_INF): \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_ZERO): \ - _FP_FRAC_COPY_##wc(R, Y); \ - R##_c = Y##_c; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_ZERO): \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_INF): \ - R##_c = FP_CLS_NAN; \ - _FP_FRAC_SET_##wc(R, _FP_NANFRAC_##fs); \ - break; \ - \ - default: \ - abort(); \ - } \ -} while (0) - - -/* - * Main division routine. The input values should be cooked. - */ - -#define _FP_DIV(fs, wc, R, X, Y) \ -do { \ - R##_s = X##_s ^ Y##_s; \ - switch (_FP_CLS_COMBINE(X##_c, Y##_c)) \ - { \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_NORMAL): \ - R##_c = FP_CLS_NORMAL; \ - R##_e = X##_e - Y##_e; \ - \ - _FP_DIV_MEAT_##fs(R,X,Y); \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_NAN): \ - _FP_CHOOSENAN(fs, wc, R, X, Y); \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_NORMAL): \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_INF): \ - case _FP_CLS_COMBINE(FP_CLS_NAN,FP_CLS_ZERO): \ - R##_s = X##_s; \ - _FP_FRAC_COPY_##wc(R, X); \ - R##_c = X##_c; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_NAN): \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_NAN): \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_NAN): \ - R##_s = Y##_s; \ - _FP_FRAC_COPY_##wc(R, Y); \ - R##_c = Y##_c; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_INF): \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_INF): \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_NORMAL): \ - R##_c = FP_CLS_ZERO; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_NORMAL,FP_CLS_ZERO): \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_ZERO): \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_NORMAL): \ - R##_c = FP_CLS_INF; \ - break; \ - \ - case _FP_CLS_COMBINE(FP_CLS_INF,FP_CLS_INF): \ - case _FP_CLS_COMBINE(FP_CLS_ZERO,FP_CLS_ZERO): \ - R##_c = FP_CLS_NAN; \ - _FP_FRAC_SET_##wc(R, _FP_NANFRAC_##fs); \ - break; \ - \ - default: \ - abort(); \ - } \ -} while (0) - - -/* - * Main differential comparison routine. The inputs should be raw not - * cooked. The return is -1,0,1 for normal values, 2 otherwise. - */ - -#define _FP_CMP(fs, wc, ret, X, Y, un) \ - do { \ - /* NANs are unordered */ \ - if ((X##_e == _FP_EXPMAX_##fs && !_FP_FRAC_ZEROP_##wc(X)) \ - || (Y##_e == _FP_EXPMAX_##fs && !_FP_FRAC_ZEROP_##wc(Y))) \ - { \ - ret = un; \ - } \ - else \ - { \ - int __x_zero = (!X##_e && _FP_FRAC_ZEROP_##wc(X)) ? 1 : 0; \ - int __y_zero = (!Y##_e && _FP_FRAC_ZEROP_##wc(Y)) ? 1 : 0; \ - \ - if (__x_zero && __y_zero) \ - ret = 0; \ - else if (__x_zero) \ - ret = Y##_s ? 1 : -1; \ - else if (__y_zero) \ - ret = X##_s ? -1 : 1; \ - else if (X##_s != Y##_s) \ - ret = X##_s ? -1 : 1; \ - else if (X##_e > Y##_e) \ - ret = X##_s ? -1 : 1; \ - else if (X##_e < Y##_e) \ - ret = X##_s ? 1 : -1; \ - else if (_FP_FRAC_GT_##wc(X, Y)) \ - ret = X##_s ? -1 : 1; \ - else if (_FP_FRAC_GT_##wc(Y, X)) \ - ret = X##_s ? 1 : -1; \ - else \ - ret = 0; \ - } \ - } while (0) - - -/* Simplification for strict equality. */ - -#define _FP_CMP_EQ(fs, wc, ret, X, Y) \ - do { \ - /* NANs are unordered */ \ - if ((X##_e == _FP_EXPMAX_##fs && !_FP_FRAC_ZEROP_##wc(X)) \ - || (Y##_e == _FP_EXPMAX_##fs && !_FP_FRAC_ZEROP_##wc(Y))) \ - { \ - ret = 1; \ - } \ - else \ - { \ - ret = !(X##_e == Y##_e \ - && _FP_FRAC_EQ_##wc(X, Y) \ - && (X##_s == Y##_s || !X##_e && _FP_FRAC_ZEROP_##wc(X))); \ - } \ - } while (0) - -/* - * Main square root routine. The input value should be cooked. - */ - -#define _FP_SQRT(fs, wc, R, X) \ -do { \ - _FP_FRAC_DECL_##wc(T); _FP_FRAC_DECL_##wc(S); \ - _FP_W_TYPE q; \ - switch (X##_c) \ - { \ - case FP_CLS_NAN: \ - R##_s = 0; \ - R##_c = FP_CLS_NAN; \ - _FP_FRAC_SET_##wc(X, _FP_ZEROFRAC_##wc); \ - break; \ - case FP_CLS_INF: \ - if (X##_s) \ - { \ - R##_s = 0; \ - R##_c = FP_CLS_NAN; /* sNAN */ \ - } \ - else \ - { \ - R##_s = 0; \ - R##_c = FP_CLS_INF; /* sqrt(+inf) = +inf */ \ - } \ - break; \ - case FP_CLS_ZERO: \ - R##_s = X##_s; \ - R##_c = FP_CLS_ZERO; /* sqrt(+-0) = +-0 */ \ - break; \ - case FP_CLS_NORMAL: \ - R##_s = 0; \ - if (X##_s) \ - { \ - R##_c = FP_CLS_NAN; /* sNAN */ \ - break; \ - } \ - R##_c = FP_CLS_NORMAL; \ - if (X##_e & 1) \ - _FP_FRAC_SLL_##wc(X, 1); \ - R##_e = X##_e >> 1; \ - _FP_FRAC_SET_##wc(S, _FP_ZEROFRAC_##wc); \ - _FP_FRAC_SET_##wc(R, _FP_ZEROFRAC_##wc); \ - q = _FP_OVERFLOW_##fs; \ - _FP_FRAC_SLL_##wc(X, 1); \ - _FP_SQRT_MEAT_##wc(R, S, T, X, q); \ - _FP_FRAC_SRL_##wc(R, 1); \ - } \ - } while (0) - -/* - * Convert from FP to integer - */ - -/* "When a NaN, infinity, large positive argument >= 2147483648.0, or - * large negative argument <= -2147483649.0 is converted to an integer, - * the invalid_current bit...should be set and fp_exception_IEEE_754 should - * be raised. If the floating point invalid trap is disabled, no trap occurs - * and a numerical result is generated: if the sign bit of the operand - * is 0, the result is 2147483647; if the sign bit of the operand is 1, - * the result is -2147483648." - * Similarly for conversion to extended ints, except that the boundaries - * are >= 2^63, <= -(2^63 + 1), and the results are 2^63 + 1 for s=0 and - * -2^63 for s=1. - * -- SPARC Architecture Manual V9, Appendix B, which specifies how - * SPARCs resolve implementation dependencies in the IEEE-754 spec. - * I don't believe that the code below follows this. I'm not even sure - * it's right! - * It doesn't cope with needing to convert to an n bit integer when there - * is no n bit integer type. Fortunately gcc provides long long so this - * isn't a problem for sparc32. - * I have, however, fixed its NaN handling to conform as above. - * -- PMM 02/1998 - * NB: rsigned is not 'is r declared signed?' but 'should the value stored - * in r be signed or unsigned?'. r is always(?) declared unsigned. - * Comments below are mine, BTW -- PMM - */ -#define _FP_TO_INT(fs, wc, r, X, rsize, rsigned) \ - do { \ - switch (X##_c) \ - { \ - case FP_CLS_NORMAL: \ - if (X##_e < 0) \ - { \ - /* case FP_CLS_NAN: see above! */ \ - case FP_CLS_ZERO: \ - r = 0; \ - } \ - else if (X##_e >= rsize - (rsigned != 0)) \ - { /* overflow */ \ - case FP_CLS_NAN: \ - case FP_CLS_INF: \ - if (rsigned) \ - { \ - r = 1; \ - r <<= rsize - 1; \ - r -= 1 - X##_s; \ - } \ - else \ - { \ - r = 0; \ - if (!X##_s) \ - r = ~r; \ - } \ - } \ - else \ - { \ - if (_FP_W_TYPE_SIZE*wc < rsize) \ - { \ - _FP_FRAC_ASSEMBLE_##wc(r, X, rsize); \ - r <<= X##_e - _FP_WFRACBITS_##fs; \ - } \ - else \ - { \ - if (X##_e >= _FP_WFRACBITS_##fs) \ - _FP_FRAC_SLL_##wc(X, (X##_e - _FP_WFRACBITS_##fs + 1));\ - else \ - _FP_FRAC_SRL_##wc(X, (_FP_WFRACBITS_##fs - X##_e - 1));\ - _FP_FRAC_ASSEMBLE_##wc(r, X, rsize); \ - } \ - if (rsigned && X##_s) \ - r = -r; \ - } \ - break; \ - } \ - } while (0) - -#define _FP_FROM_INT(fs, wc, X, r, rsize, rtype) \ - do { \ - if (r) \ - { \ - X##_c = FP_CLS_NORMAL; \ - \ - if ((X##_s = (r < 0))) \ - r = -r; \ - /* Note that `r' is now considered unsigned, so we don't have \ - to worry about the single signed overflow case. */ \ - \ - if (rsize <= _FP_W_TYPE_SIZE) \ - __FP_CLZ(X##_e, r); \ - else \ - __FP_CLZ_2(X##_e, (_FP_W_TYPE)(r >> _FP_W_TYPE_SIZE), \ - (_FP_W_TYPE)r); \ - if (rsize < _FP_W_TYPE_SIZE) \ - X##_e -= (_FP_W_TYPE_SIZE - rsize); \ - X##_e = rsize - X##_e - 1; \ - \ - if (_FP_FRACBITS_##fs < rsize && _FP_WFRACBITS_##fs < X##_e) \ - __FP_FRAC_SRS_1(r, (X##_e - _FP_WFRACBITS_##fs), rsize); \ - r &= ~((_FP_W_TYPE)1 << X##_e); \ - _FP_FRAC_DISASSEMBLE_##wc(X, ((unsigned rtype)r), rsize); \ - _FP_FRAC_SLL_##wc(X, (_FP_WFRACBITS_##fs - X##_e - 1)); \ - } \ - else \ - { \ - X##_c = FP_CLS_ZERO, X##_s = 0; \ - } \ - } while (0) - - -#define FP_CONV(dfs,sfs,dwc,swc,D,S) \ - do { \ - _FP_FRAC_CONV_##dwc##_##swc(dfs, sfs, D, S); \ - D##_e = S##_e; \ - D##_c = S##_c; \ - D##_s = S##_s; \ - } while (0) - -/* - * Helper primitives. - */ - -/* Count leading zeros in a word. */ - -#ifndef __FP_CLZ -#if _FP_W_TYPE_SIZE < 64 -/* this is just to shut the compiler up about shifts > word length -- PMM 02/1998 */ -#define __FP_CLZ(r, x) \ - do { \ - _FP_W_TYPE _t = (x); \ - r = _FP_W_TYPE_SIZE - 1; \ - if (_t > 0xffff) r -= 16; \ - if (_t > 0xffff) _t >>= 16; \ - if (_t > 0xff) r -= 8; \ - if (_t > 0xff) _t >>= 8; \ - if (_t & 0xf0) r -= 4; \ - if (_t & 0xf0) _t >>= 4; \ - if (_t & 0xc) r -= 2; \ - if (_t & 0xc) _t >>= 2; \ - if (_t & 0x2) r -= 1; \ - } while (0) -#else /* not _FP_W_TYPE_SIZE < 64 */ -#define __FP_CLZ(r, x) \ - do { \ - _FP_W_TYPE _t = (x); \ - r = _FP_W_TYPE_SIZE - 1; \ - if (_t > 0xffffffff) r -= 32; \ - if (_t > 0xffffffff) _t >>= 32; \ - if (_t > 0xffff) r -= 16; \ - if (_t > 0xffff) _t >>= 16; \ - if (_t > 0xff) r -= 8; \ - if (_t > 0xff) _t >>= 8; \ - if (_t & 0xf0) r -= 4; \ - if (_t & 0xf0) _t >>= 4; \ - if (_t & 0xc) r -= 2; \ - if (_t & 0xc) _t >>= 2; \ - if (_t & 0x2) r -= 1; \ - } while (0) -#endif /* not _FP_W_TYPE_SIZE < 64 */ -#endif /* ndef __FP_CLZ */ - -#define _FP_DIV_HELP_imm(q, r, n, d) \ - do { \ - q = n / d, r = n % d; \ - } while (0) - diff --git a/arch/powerpc/math-emu/sfp-machine.h b/arch/powerpc/math-emu/sfp-machine.h deleted file mode 100644 index 4b17d83cfcd..00000000000 --- a/arch/powerpc/math-emu/sfp-machine.h +++ /dev/null @@ -1,377 +0,0 @@ -/* Machine-dependent software floating-point definitions. PPC version. - Copyright (C) 1997 Free Software Foundation, Inc. - This file is part of the GNU C Library. - - The GNU C Library is free software; you can redistribute it and/or - modify it under the terms of the GNU Library General Public License as - published by the Free Software Foundation; either version 2 of the - License, or (at your option) any later version. - - The GNU C Library is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU - Library General Public License for more details. - - You should have received a copy of the GNU Library General Public - License along with the GNU C Library; see the file COPYING.LIB. If - not, write to the Free Software Foundation, Inc., - 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - - Actually, this is a PPC (32bit) version, written based on the - i386, sparc, and sparc64 versions, by me, - Peter Maydell (pmaydell@chiark.greenend.org.uk). - Comments are by and large also mine, although they may be inaccurate. - - In picking out asm fragments I've gone with the lowest common - denominator, which also happens to be the hardware I have :-> - That is, a SPARC without hardware multiply and divide. - */ - -/* basic word size definitions */ -#define _FP_W_TYPE_SIZE 32 -#define _FP_W_TYPE unsigned long -#define _FP_WS_TYPE signed long -#define _FP_I_TYPE long - -#define __ll_B ((UWtype) 1 << (W_TYPE_SIZE / 2)) -#define __ll_lowpart(t) ((UWtype) (t) & (__ll_B - 1)) -#define __ll_highpart(t) ((UWtype) (t) >> (W_TYPE_SIZE / 2)) - -/* You can optionally code some things like addition in asm. For - * example, i386 defines __FP_FRAC_ADD_2 as asm. If you don't - * then you get a fragment of C code [if you change an #ifdef 0 - * in op-2.h] or a call to add_ssaaaa (see below). - * Good places to look for asm fragments to use are gcc and glibc. - * gcc's longlong.h is useful. - */ - -/* We need to know how to multiply and divide. If the host word size - * is >= 2*fracbits you can use FP_MUL_MEAT_n_imm(t,R,X,Y) which - * codes the multiply with whatever gcc does to 'a * b'. - * _FP_MUL_MEAT_n_wide(t,R,X,Y,f) is used when you have an asm - * function that can multiply two 1W values and get a 2W result. - * Otherwise you're stuck with _FP_MUL_MEAT_n_hard(t,R,X,Y) which - * does bitshifting to avoid overflow. - * For division there is FP_DIV_MEAT_n_imm(t,R,X,Y,f) for word size - * >= 2*fracbits, where f is either _FP_DIV_HELP_imm or - * _FP_DIV_HELP_ldiv (see op-1.h). - * _FP_DIV_MEAT_udiv() is if you have asm to do 2W/1W => (1W, 1W). - * [GCC and glibc have longlong.h which has the asm macro udiv_qrnnd - * to do this.] - * In general, 'n' is the number of words required to hold the type, - * and 't' is either S, D or Q for single/double/quad. - * -- PMM - */ -/* Example: SPARC64: - * #define _FP_MUL_MEAT_S(R,X,Y) _FP_MUL_MEAT_1_imm(S,R,X,Y) - * #define _FP_MUL_MEAT_D(R,X,Y) _FP_MUL_MEAT_1_wide(D,R,X,Y,umul_ppmm) - * #define _FP_MUL_MEAT_Q(R,X,Y) _FP_MUL_MEAT_2_wide(Q,R,X,Y,umul_ppmm) - * - * #define _FP_DIV_MEAT_S(R,X,Y) _FP_DIV_MEAT_1_imm(S,R,X,Y,_FP_DIV_HELP_imm) - * #define _FP_DIV_MEAT_D(R,X,Y) _FP_DIV_MEAT_1_udiv(D,R,X,Y) - * #define _FP_DIV_MEAT_Q(R,X,Y) _FP_DIV_MEAT_2_udiv_64(Q,R,X,Y) - * - * Example: i386: - * #define _FP_MUL_MEAT_S(R,X,Y) _FP_MUL_MEAT_1_wide(S,R,X,Y,_i386_mul_32_64) - * #define _FP_MUL_MEAT_D(R,X,Y) _FP_MUL_MEAT_2_wide(D,R,X,Y,_i386_mul_32_64) - * - * #define _FP_DIV_MEAT_S(R,X,Y) _FP_DIV_MEAT_1_udiv(S,R,X,Y,_i386_div_64_32) - * #define _FP_DIV_MEAT_D(R,X,Y) _FP_DIV_MEAT_2_udiv_64(D,R,X,Y) - */ - -#define _FP_MUL_MEAT_S(R,X,Y) _FP_MUL_MEAT_1_wide(S,R,X,Y,umul_ppmm) -#define _FP_MUL_MEAT_D(R,X,Y) _FP_MUL_MEAT_2_wide(D,R,X,Y,umul_ppmm) - -#define _FP_DIV_MEAT_S(R,X,Y) _FP_DIV_MEAT_1_udiv(S,R,X,Y) -#define _FP_DIV_MEAT_D(R,X,Y) _FP_DIV_MEAT_2_udiv_64(D,R,X,Y) - -/* These macros define what NaN looks like. They're supposed to expand to - * a comma-separated set of 32bit unsigned ints that encode NaN. - */ -#define _FP_NANFRAC_S _FP_QNANBIT_S -#define _FP_NANFRAC_D _FP_QNANBIT_D, 0 -#define _FP_NANFRAC_Q _FP_QNANBIT_Q, 0, 0, 0 - -#define _FP_KEEPNANFRACP 1 - -/* This macro appears to be called when both X and Y are NaNs, and - * has to choose one and copy it to R. i386 goes for the larger of the - * two, sparc64 just picks Y. I don't understand this at all so I'll - * go with sparc64 because it's shorter :-> -- PMM - */ -#define _FP_CHOOSENAN(fs, wc, R, X, Y) \ - do { \ - R##_s = Y##_s; \ - _FP_FRAC_COPY_##wc(R,Y); \ - R##_c = FP_CLS_NAN; \ - } while (0) - - -extern void fp_unpack_d(long *, unsigned long *, unsigned long *, - long *, long *, void *); -extern int fp_pack_d(void *, long, unsigned long, unsigned long, long, long); -extern int fp_pack_ds(void *, long, unsigned long, unsigned long, long, long); - -#define __FP_UNPACK_RAW_1(fs, X, val) \ - do { \ - union _FP_UNION_##fs *_flo = \ - (union _FP_UNION_##fs *)val; \ - \ - X##_f = _flo->bits.frac; \ - X##_e = _flo->bits.exp; \ - X##_s = _flo->bits.sign; \ - } while (0) - -#define __FP_UNPACK_RAW_2(fs, X, val) \ - do { \ - union _FP_UNION_##fs *_flo = \ - (union _FP_UNION_##fs *)val; \ - \ - X##_f0 = _flo->bits.frac0; \ - X##_f1 = _flo->bits.frac1; \ - X##_e = _flo->bits.exp; \ - X##_s = _flo->bits.sign; \ - } while (0) - -#define __FP_UNPACK_S(X,val) \ - do { \ - __FP_UNPACK_RAW_1(S,X,val); \ - _FP_UNPACK_CANONICAL(S,1,X); \ - } while (0) - -#define __FP_UNPACK_D(X,val) \ - fp_unpack_d(&X##_s, &X##_f1, &X##_f0, &X##_e, &X##_c, val) - -#define __FP_PACK_RAW_1(fs, val, X) \ - do { \ - union _FP_UNION_##fs *_flo = \ - (union _FP_UNION_##fs *)val; \ - \ - _flo->bits.frac = X##_f; \ - _flo->bits.exp = X##_e; \ - _flo->bits.sign = X##_s; \ - } while (0) - -#define __FP_PACK_RAW_2(fs, val, X) \ - do { \ - union _FP_UNION_##fs *_flo = \ - (union _FP_UNION_##fs *)val; \ - \ - _flo->bits.frac0 = X##_f0; \ - _flo->bits.frac1 = X##_f1; \ - _flo->bits.exp = X##_e; \ - _flo->bits.sign = X##_s; \ - } while (0) - -#include -#include - -#define __FPU_FPSCR (current->thread.fpscr.val) - -/* We only actually write to the destination register - * if exceptions signalled (if any) will not trap. - */ -#define __FPU_ENABLED_EXC \ -({ \ - (__FPU_FPSCR >> 3) & 0x1f; \ -}) - -#define __FPU_TRAP_P(bits) \ - ((__FPU_ENABLED_EXC & (bits)) != 0) - -#define __FP_PACK_S(val,X) \ -({ int __exc = _FP_PACK_CANONICAL(S,1,X); \ - if(!__exc || !__FPU_TRAP_P(__exc)) \ - __FP_PACK_RAW_1(S,val,X); \ - __exc; \ -}) - -#define __FP_PACK_D(val,X) \ - fp_pack_d(val, X##_s, X##_f1, X##_f0, X##_e, X##_c) - -#define __FP_PACK_DS(val,X) \ - fp_pack_ds(val, X##_s, X##_f1, X##_f0, X##_e, X##_c) - -/* Obtain the current rounding mode. */ -#define FP_ROUNDMODE \ -({ \ - __FPU_FPSCR & 0x3; \ -}) - -/* the asm fragments go here: all these are taken from glibc-2.0.5's - * stdlib/longlong.h - */ - -#include -#include - -/* add_ssaaaa is used in op-2.h and should be equivalent to - * #define add_ssaaaa(sh,sl,ah,al,bh,bl) (sh = ah+bh+ (( sl = al+bl) < al)) - * add_ssaaaa(high_sum, low_sum, high_addend_1, low_addend_1, - * high_addend_2, low_addend_2) adds two UWtype integers, composed by - * HIGH_ADDEND_1 and LOW_ADDEND_1, and HIGH_ADDEND_2 and LOW_ADDEND_2 - * respectively. The result is placed in HIGH_SUM and LOW_SUM. Overflow - * (i.e. carry out) is not stored anywhere, and is lost. - */ -#define add_ssaaaa(sh, sl, ah, al, bh, bl) \ - do { \ - if (__builtin_constant_p (bh) && (bh) == 0) \ - __asm__ ("{a%I4|add%I4c} %1,%3,%4\n\t{aze|addze} %0,%2" \ - : "=r" ((USItype)(sh)), \ - "=&r" ((USItype)(sl)) \ - : "%r" ((USItype)(ah)), \ - "%r" ((USItype)(al)), \ - "rI" ((USItype)(bl))); \ - else if (__builtin_constant_p (bh) && (bh) ==~(USItype) 0) \ - __asm__ ("{a%I4|add%I4c} %1,%3,%4\n\t{ame|addme} %0,%2" \ - : "=r" ((USItype)(sh)), \ - "=&r" ((USItype)(sl)) \ - : "%r" ((USItype)(ah)), \ - "%r" ((USItype)(al)), \ - "rI" ((USItype)(bl))); \ - else \ - __asm__ ("{a%I5|add%I5c} %1,%4,%5\n\t{ae|adde} %0,%2,%3" \ - : "=r" ((USItype)(sh)), \ - "=&r" ((USItype)(sl)) \ - : "%r" ((USItype)(ah)), \ - "r" ((USItype)(bh)), \ - "%r" ((USItype)(al)), \ - "rI" ((USItype)(bl))); \ - } while (0) - -/* sub_ddmmss is used in op-2.h and udivmodti4.c and should be equivalent to - * #define sub_ddmmss(sh, sl, ah, al, bh, bl) (sh = ah-bh - ((sl = al-bl) > al)) - * sub_ddmmss(high_difference, low_difference, high_minuend, low_minuend, - * high_subtrahend, low_subtrahend) subtracts two two-word UWtype integers, - * composed by HIGH_MINUEND_1 and LOW_MINUEND_1, and HIGH_SUBTRAHEND_2 and - * LOW_SUBTRAHEND_2 respectively. The result is placed in HIGH_DIFFERENCE - * and LOW_DIFFERENCE. Overflow (i.e. carry out) is not stored anywhere, - * and is lost. - */ -#define sub_ddmmss(sh, sl, ah, al, bh, bl) \ - do { \ - if (__builtin_constant_p (ah) && (ah) == 0) \ - __asm__ ("{sf%I3|subf%I3c} %1,%4,%3\n\t{sfze|subfze} %0,%2" \ - : "=r" ((USItype)(sh)), \ - "=&r" ((USItype)(sl)) \ - : "r" ((USItype)(bh)), \ - "rI" ((USItype)(al)), \ - "r" ((USItype)(bl))); \ - else if (__builtin_constant_p (ah) && (ah) ==~(USItype) 0) \ - __asm__ ("{sf%I3|subf%I3c} %1,%4,%3\n\t{sfme|subfme} %0,%2" \ - : "=r" ((USItype)(sh)), \ - "=&r" ((USItype)(sl)) \ - : "r" ((USItype)(bh)), \ - "rI" ((USItype)(al)), \ - "r" ((USItype)(bl))); \ - else if (__builtin_constant_p (bh) && (bh) == 0) \ - __asm__ ("{sf%I3|subf%I3c} %1,%4,%3\n\t{ame|addme} %0,%2" \ - : "=r" ((USItype)(sh)), \ - "=&r" ((USItype)(sl)) \ - : "r" ((USItype)(ah)), \ - "rI" ((USItype)(al)), \ - "r" ((USItype)(bl))); \ - else if (__builtin_constant_p (bh) && (bh) ==~(USItype) 0) \ - __asm__ ("{sf%I3|subf%I3c} %1,%4,%3\n\t{aze|addze} %0,%2" \ - : "=r" ((USItype)(sh)), \ - "=&r" ((USItype)(sl)) \ - : "r" ((USItype)(ah)), \ - "rI" ((USItype)(al)), \ - "r" ((USItype)(bl))); \ - else \ - __asm__ ("{sf%I4|subf%I4c} %1,%5,%4\n\t{sfe|subfe} %0,%3,%2" \ - : "=r" ((USItype)(sh)), \ - "=&r" ((USItype)(sl)) \ - : "r" ((USItype)(ah)), \ - "r" ((USItype)(bh)), \ - "rI" ((USItype)(al)), \ - "r" ((USItype)(bl))); \ - } while (0) - -/* asm fragments for mul and div */ - -/* umul_ppmm(high_prod, low_prod, multipler, multiplicand) multiplies two - * UWtype integers MULTIPLER and MULTIPLICAND, and generates a two UWtype - * word product in HIGH_PROD and LOW_PROD. - */ -#define umul_ppmm(ph, pl, m0, m1) \ - do { \ - USItype __m0 = (m0), __m1 = (m1); \ - __asm__ ("mulhwu %0,%1,%2" \ - : "=r" ((USItype)(ph)) \ - : "%r" (__m0), \ - "r" (__m1)); \ - (pl) = __m0 * __m1; \ - } while (0) - -/* udiv_qrnnd(quotient, remainder, high_numerator, low_numerator, - * denominator) divides a UDWtype, composed by the UWtype integers - * HIGH_NUMERATOR and LOW_NUMERATOR, by DENOMINATOR and places the quotient - * in QUOTIENT and the remainder in REMAINDER. HIGH_NUMERATOR must be less - * than DENOMINATOR for correct operation. If, in addition, the most - * significant bit of DENOMINATOR must be 1, then the pre-processor symbol - * UDIV_NEEDS_NORMALIZATION is defined to 1. - */ -#define udiv_qrnnd(q, r, n1, n0, d) \ - do { \ - UWtype __d1, __d0, __q1, __q0, __r1, __r0, __m; \ - __d1 = __ll_highpart (d); \ - __d0 = __ll_lowpart (d); \ - \ - __r1 = (n1) % __d1; \ - __q1 = (n1) / __d1; \ - __m = (UWtype) __q1 * __d0; \ - __r1 = __r1 * __ll_B | __ll_highpart (n0); \ - if (__r1 < __m) \ - { \ - __q1--, __r1 += (d); \ - if (__r1 >= (d)) /* we didn't get carry when adding to __r1 */ \ - if (__r1 < __m) \ - __q1--, __r1 += (d); \ - } \ - __r1 -= __m; \ - \ - __r0 = __r1 % __d1; \ - __q0 = __r1 / __d1; \ - __m = (UWtype) __q0 * __d0; \ - __r0 = __r0 * __ll_B | __ll_lowpart (n0); \ - if (__r0 < __m) \ - { \ - __q0--, __r0 += (d); \ - if (__r0 >= (d)) \ - if (__r0 < __m) \ - __q0--, __r0 += (d); \ - } \ - __r0 -= __m; \ - \ - (q) = (UWtype) __q1 * __ll_B | __q0; \ - (r) = __r0; \ - } while (0) - -#define UDIV_NEEDS_NORMALIZATION 1 - -#define abort() \ - return 0 - -#ifdef __BIG_ENDIAN -#define __BYTE_ORDER __BIG_ENDIAN -#else -#define __BYTE_ORDER __LITTLE_ENDIAN -#endif - -/* Exception flags. */ -#define EFLAG_INVALID (1 << (31 - 2)) -#define EFLAG_OVERFLOW (1 << (31 - 3)) -#define EFLAG_UNDERFLOW (1 << (31 - 4)) -#define EFLAG_DIVZERO (1 << (31 - 5)) -#define EFLAG_INEXACT (1 << (31 - 6)) - -#define EFLAG_VXSNAN (1 << (31 - 7)) -#define EFLAG_VXISI (1 << (31 - 8)) -#define EFLAG_VXIDI (1 << (31 - 9)) -#define EFLAG_VXZDZ (1 << (31 - 10)) -#define EFLAG_VXIMZ (1 << (31 - 11)) -#define EFLAG_VXVC (1 << (31 - 12)) -#define EFLAG_VXSOFT (1 << (31 - 21)) -#define EFLAG_VXSQRT (1 << (31 - 22)) -#define EFLAG_VXCVI (1 << (31 - 23)) diff --git a/arch/powerpc/math-emu/single.h b/arch/powerpc/math-emu/single.h deleted file mode 100644 index f19d9945181..00000000000 --- a/arch/powerpc/math-emu/single.h +++ /dev/null @@ -1,66 +0,0 @@ -/* - * Definitions for IEEE Single Precision - */ - -#if _FP_W_TYPE_SIZE < 32 -#error "Here's a nickel kid. Go buy yourself a real computer." -#endif - -#define _FP_FRACBITS_S 24 -#define _FP_FRACXBITS_S (_FP_W_TYPE_SIZE - _FP_FRACBITS_S) -#define _FP_WFRACBITS_S (_FP_WORKBITS + _FP_FRACBITS_S) -#define _FP_WFRACXBITS_S (_FP_W_TYPE_SIZE - _FP_WFRACBITS_S) -#define _FP_EXPBITS_S 8 -#define _FP_EXPBIAS_S 127 -#define _FP_EXPMAX_S 255 -#define _FP_QNANBIT_S ((_FP_W_TYPE)1 << (_FP_FRACBITS_S-2)) -#define _FP_IMPLBIT_S ((_FP_W_TYPE)1 << (_FP_FRACBITS_S-1)) -#define _FP_OVERFLOW_S ((_FP_W_TYPE)1 << (_FP_WFRACBITS_S)) - -/* The implementation of _FP_MUL_MEAT_S and _FP_DIV_MEAT_S should be - chosen by the target machine. */ - -union _FP_UNION_S -{ - float flt; - struct { -#if __BYTE_ORDER == __BIG_ENDIAN - unsigned sign : 1; - unsigned exp : _FP_EXPBITS_S; - unsigned frac : _FP_FRACBITS_S - (_FP_IMPLBIT_S != 0); -#else - unsigned frac : _FP_FRACBITS_S - (_FP_IMPLBIT_S != 0); - unsigned exp : _FP_EXPBITS_S; - unsigned sign : 1; -#endif - } bits __attribute__((packed)); -}; - -#define FP_DECL_S(X) _FP_DECL(1,X) -#define FP_UNPACK_RAW_S(X,val) _FP_UNPACK_RAW_1(S,X,val) -#define FP_PACK_RAW_S(val,X) _FP_PACK_RAW_1(S,val,X) - -#define FP_UNPACK_S(X,val) \ - do { \ - _FP_UNPACK_RAW_1(S,X,val); \ - _FP_UNPACK_CANONICAL(S,1,X); \ - } while (0) - -#define FP_PACK_S(val,X) \ - do { \ - _FP_PACK_CANONICAL(S,1,X); \ - _FP_PACK_RAW_1(S,val,X); \ - } while (0) - -#define FP_NEG_S(R,X) _FP_NEG(S,1,R,X) -#define FP_ADD_S(R,X,Y) _FP_ADD(S,1,R,X,Y) -#define FP_SUB_S(R,X,Y) _FP_SUB(S,1,R,X,Y) -#define FP_MUL_S(R,X,Y) _FP_MUL(S,1,R,X,Y) -#define FP_DIV_S(R,X,Y) _FP_DIV(S,1,R,X,Y) -#define FP_SQRT_S(R,X) _FP_SQRT(S,1,R,X) - -#define FP_CMP_S(r,X,Y,un) _FP_CMP(S,1,r,X,Y,un) -#define FP_CMP_EQ_S(r,X,Y) _FP_CMP_EQ(S,1,r,X,Y) - -#define FP_TO_INT_S(r,X,rsz,rsg) _FP_TO_INT(S,1,r,X,rsz,rsg) -#define FP_FROM_INT_S(X,r,rs,rt) _FP_FROM_INT(S,1,X,r,rs,rt) diff --git a/arch/powerpc/math-emu/soft-fp.h b/arch/powerpc/math-emu/soft-fp.h deleted file mode 100644 index cca39598f87..00000000000 --- a/arch/powerpc/math-emu/soft-fp.h +++ /dev/null @@ -1,104 +0,0 @@ -#ifndef SOFT_FP_H -#define SOFT_FP_H - -#include "sfp-machine.h" - -#define _FP_WORKBITS 3 -#define _FP_WORK_LSB ((_FP_W_TYPE)1 << 3) -#define _FP_WORK_ROUND ((_FP_W_TYPE)1 << 2) -#define _FP_WORK_GUARD ((_FP_W_TYPE)1 << 1) -#define _FP_WORK_STICKY ((_FP_W_TYPE)1 << 0) - -#ifndef FP_RND_NEAREST -# define FP_RND_NEAREST 0 -# define FP_RND_ZERO 1 -# define FP_RND_PINF 2 -# define FP_RND_MINF 3 -#ifndef FP_ROUNDMODE -# define FP_ROUNDMODE FP_RND_NEAREST -#endif -#endif - -#define _FP_ROUND_NEAREST(wc, X) \ -({ int __ret = 0; \ - int __frac = _FP_FRAC_LOW_##wc(X) & 15; \ - if (__frac & 7) { \ - __ret = EFLAG_INEXACT; \ - if ((__frac & 7) != _FP_WORK_ROUND) \ - _FP_FRAC_ADDI_##wc(X, _FP_WORK_ROUND); \ - else if (__frac & _FP_WORK_LSB) \ - _FP_FRAC_ADDI_##wc(X, _FP_WORK_ROUND); \ - } \ - __ret; \ -}) - -#define _FP_ROUND_ZERO(wc, X) \ -({ int __ret = 0; \ - if (_FP_FRAC_LOW_##wc(X) & 7) \ - __ret = EFLAG_INEXACT; \ - __ret; \ -}) - -#define _FP_ROUND_PINF(wc, X) \ -({ int __ret = EFLAG_INEXACT; \ - if (!X##_s && (_FP_FRAC_LOW_##wc(X) & 7)) \ - _FP_FRAC_ADDI_##wc(X, _FP_WORK_LSB); \ - else __ret = 0; \ - __ret; \ -}) - -#define _FP_ROUND_MINF(wc, X) \ -({ int __ret = EFLAG_INEXACT; \ - if (X##_s && (_FP_FRAC_LOW_##wc(X) & 7)) \ - _FP_FRAC_ADDI_##wc(X, _FP_WORK_LSB); \ - else __ret = 0; \ - __ret; \ -}) - -#define _FP_ROUND(wc, X) \ -({ int __ret = 0; \ - switch (FP_ROUNDMODE) \ - { \ - case FP_RND_NEAREST: \ - __ret |= _FP_ROUND_NEAREST(wc,X); \ - break; \ - case FP_RND_ZERO: \ - __ret |= _FP_ROUND_ZERO(wc,X); \ - break; \ - case FP_RND_PINF: \ - __ret |= _FP_ROUND_PINF(wc,X); \ - break; \ - case FP_RND_MINF: \ - __ret |= _FP_ROUND_MINF(wc,X); \ - break; \ - }; \ - __ret; \ -}) - -#define FP_CLS_NORMAL 0 -#define FP_CLS_ZERO 1 -#define FP_CLS_INF 2 -#define FP_CLS_NAN 3 - -#define _FP_CLS_COMBINE(x,y) (((x) << 2) | (y)) - -#include "op-1.h" -#include "op-2.h" -#include "op-4.h" -#include "op-common.h" - -/* Sigh. Silly things longlong.h needs. */ -#define UWtype _FP_W_TYPE -#define W_TYPE_SIZE _FP_W_TYPE_SIZE - -typedef int SItype __attribute__((mode(SI))); -typedef int DItype __attribute__((mode(DI))); -typedef unsigned int USItype __attribute__((mode(SI))); -typedef unsigned int UDItype __attribute__((mode(DI))); -#if _FP_W_TYPE_SIZE == 32 -typedef unsigned int UHWtype __attribute__((mode(HI))); -#elif _FP_W_TYPE_SIZE == 64 -typedef USItype UHWtype; -#endif - -#endif diff --git a/arch/powerpc/math-emu/stfs.c b/arch/powerpc/math-emu/stfs.c index 8689aa48ef6..6122147356d 100644 --- a/arch/powerpc/math-emu/stfs.c +++ b/arch/powerpc/math-emu/stfs.c @@ -2,23 +2,24 @@ #include #include -#include "soft-fp.h" -#include "double.h" -#include "single.h" +#include +#include +#include +#include int stfs(void *frS, void *ea) { FP_DECL_D(A); FP_DECL_S(R); + FP_DECL_EX; float f; - int err; #ifdef DEBUG printk("%s: S %p, ea %p\n", __func__, frS, ea); #endif - __FP_UNPACK_D(A, frS); + FP_UNPACK_DP(A, frS); #ifdef DEBUG printk("A: %ld %lu %lu %ld (%ld)\n", A_s, A_f1, A_f0, A_e, A_c); @@ -30,12 +31,12 @@ stfs(void *frS, void *ea) printk("R: %ld %lu %ld (%ld)\n", R_s, R_f, R_e, R_c); #endif - err = _FP_PACK_CANONICAL(S, 1, R); - if (!err || !__FPU_TRAP_P(err)) { - __FP_PACK_RAW_1(S, &f, R); + _FP_PACK_CANONICAL(S, 1, R); + if (!FP_CUR_EXCEPTIONS || !__FPU_TRAP_P(FP_CUR_EXCEPTIONS)) { + _FP_PACK_RAW_1_P(S, &f, R); if (copy_to_user(ea, &f, sizeof(float))) return -EFAULT; } - return err; + return FP_CUR_EXCEPTIONS; } diff --git a/arch/powerpc/math-emu/types.c b/arch/powerpc/math-emu/types.c deleted file mode 100644 index e1ed15d829d..00000000000 --- a/arch/powerpc/math-emu/types.c +++ /dev/null @@ -1,51 +0,0 @@ -#include "soft-fp.h" -#include "double.h" -#include "single.h" - -void -fp_unpack_d(long *_s, unsigned long *_f1, unsigned long *_f0, - long *_e, long *_c, void *val) -{ - FP_DECL_D(X); - - __FP_UNPACK_RAW_2(D, X, val); - - _FP_UNPACK_CANONICAL(D, 2, X); - - *_s = X_s; - *_f1 = X_f1; - *_f0 = X_f0; - *_e = X_e; - *_c = X_c; -} - -int -fp_pack_d(void *val, long X_s, unsigned long X_f1, - unsigned long X_f0, long X_e, long X_c) -{ - int exc; - - exc = _FP_PACK_CANONICAL(D, 2, X); - if (!exc || !__FPU_TRAP_P(exc)) - __FP_PACK_RAW_2(D, val, X); - return exc; -} - -int -fp_pack_ds(void *val, long X_s, unsigned long X_f1, - unsigned long X_f0, long X_e, long X_c) -{ - FP_DECL_S(__X); - int exc; - - FP_CONV(S, D, 1, 2, __X, X); - exc = _FP_PACK_CANONICAL(S, 1, __X); - if (!exc || !__FPU_TRAP_P(exc)) { - _FP_UNPACK_CANONICAL(S, 1, __X); - FP_CONV(D, S, 2, 1, X, __X); - exc |= _FP_PACK_CANONICAL(D, 2, X); - if (!exc || !__FPU_TRAP_P(exc)) - __FP_PACK_RAW_2(D, val, X); - } - return exc; -} diff --git a/arch/powerpc/math-emu/udivmodti4.c b/arch/powerpc/math-emu/udivmodti4.c index 7e112dc1e2f..6172044ab00 100644 --- a/arch/powerpc/math-emu/udivmodti4.c +++ b/arch/powerpc/math-emu/udivmodti4.c @@ -1,6 +1,6 @@ /* This has so very few changes over libgcc2's __udivmoddi4 it isn't funny. */ -#include "soft-fp.h" +#include #undef count_leading_zeros #define count_leading_zeros __FP_CLZ -- cgit v1.2.3 From 5a013fc7bb48acefe94011f4b83fef95b381f875 Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Wed, 10 Sep 2008 05:55:46 +0000 Subject: powerpc/4xx: Allow 4xx PCI bridge to be disabled via device tree This patch allows the 4xx (conventional) PCI bridge to be disabled via the device tree. This is needed for 4xx PCI adapter hardware. Use the PCI node's status property to disable the PCI bridge. Signed-off-by: Matthias Fuchs Acked-by: Stefan Roese Signed-off-by: Josh Boyer --- arch/powerpc/sysdev/ppc4xx_pci.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/ppc4xx_pci.c b/arch/powerpc/sysdev/ppc4xx_pci.c index 5da8a44ea2f..9f6f73d584d 100644 --- a/arch/powerpc/sysdev/ppc4xx_pci.c +++ b/arch/powerpc/sysdev/ppc4xx_pci.c @@ -276,9 +276,16 @@ static void __init ppc4xx_probe_pci_bridge(struct device_node *np) const int *bus_range; int primary = 0; + /* Check if device is enabled */ + if (!of_device_is_available(np)) { + printk(KERN_INFO "%s: Port disabled via device-tree\n", + np->full_name); + return; + } + /* Fetch config space registers address */ if (of_address_to_resource(np, 0, &rsrc_cfg)) { - printk(KERN_ERR "%s:Can't get PCI config register base !", + printk(KERN_ERR "%s: Can't get PCI config register base !", np->full_name); return; } -- cgit v1.2.3 From 9e3cb29497561c846d0e7efc445731764d93c749 Mon Sep 17 00:00:00 2001 From: Victor Gallardo Date: Wed, 1 Oct 2008 23:37:57 -0700 Subject: ibm_newemac: Add support for GPCS, SGMII and M88E1112 PHY Add support for the phy types found on the Arches and other PowerPC 460 based boards. Signed-off-by: Victor Gallardo Acked-by: Benjamin Herrenschmidt Acked-by: Jeff Garzik Signed-off-by: Josh Boyer --- arch/powerpc/include/asm/dcr-regs.h | 4 ++ drivers/net/ibm_newemac/core.c | 58 +++++++++++++++++++++---- drivers/net/ibm_newemac/core.h | 8 ++++ drivers/net/ibm_newemac/phy.c | 84 +++++++++++++++++++++++++++++++++++++ drivers/net/ibm_newemac/phy.h | 2 + 5 files changed, 147 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/dcr-regs.h b/arch/powerpc/include/asm/dcr-regs.h index 7b833ff9c14..828e3aa1f2f 100644 --- a/arch/powerpc/include/asm/dcr-regs.h +++ b/arch/powerpc/include/asm/dcr-regs.h @@ -75,6 +75,10 @@ #define ICINTSTAT_ICTX1 0x20000000 #define ICINTSTAT_ICTX 0x60000000 +/* SDRs (460EX/460GT) */ +#define SDR0_ETH_CFG 0x4103 +#define SDR0_ETH_CFG_ECS 0x00000100 /* EMAC int clk source */ + /* * All those DCR register addresses are offsets from the base address * for the SRAM0 controller (e.g. 0x20 on 440GX). The base address is diff --git a/drivers/net/ibm_newemac/core.c b/drivers/net/ibm_newemac/core.c index 4e633870e6e..efcf21c9f5c 100644 --- a/drivers/net/ibm_newemac/core.c +++ b/drivers/net/ibm_newemac/core.c @@ -130,6 +130,7 @@ static inline void emac_report_timeout_error(struct emac_instance *dev, const char *error) { if (emac_has_feature(dev, EMAC_FTR_440GX_PHY_CLK_FIX | + EMAC_FTR_460EX_PHY_CLK_FIX | EMAC_FTR_440EP_PHY_CLK_FIX)) DBG(dev, "%s" NL, error); else if (net_ratelimit()) @@ -201,13 +202,15 @@ static inline int emac_phy_supports_gige(int phy_mode) { return phy_mode == PHY_MODE_GMII || phy_mode == PHY_MODE_RGMII || + phy_mode == PHY_MODE_SGMII || phy_mode == PHY_MODE_TBI || phy_mode == PHY_MODE_RTBI; } static inline int emac_phy_gpcs(int phy_mode) { - return phy_mode == PHY_MODE_TBI || + return phy_mode == PHY_MODE_SGMII || + phy_mode == PHY_MODE_TBI || phy_mode == PHY_MODE_RTBI; } @@ -351,10 +354,24 @@ static int emac_reset(struct emac_instance *dev) emac_tx_disable(dev); } +#ifdef CONFIG_PPC_DCR_NATIVE + /* Enable internal clock source */ + if (emac_has_feature(dev, EMAC_FTR_460EX_PHY_CLK_FIX)) + dcri_clrset(SDR0, SDR0_ETH_CFG, + 0, SDR0_ETH_CFG_ECS << dev->cell_index); +#endif + out_be32(&p->mr0, EMAC_MR0_SRST); while ((in_be32(&p->mr0) & EMAC_MR0_SRST) && n) --n; +#ifdef CONFIG_PPC_DCR_NATIVE + /* Enable external clock source */ + if (emac_has_feature(dev, EMAC_FTR_460EX_PHY_CLK_FIX)) + dcri_clrset(SDR0, SDR0_ETH_CFG, + SDR0_ETH_CFG_ECS << dev->cell_index, 0); +#endif + if (n) { dev->reset_failed = 0; return 0; @@ -547,8 +564,9 @@ static int emac_configure(struct emac_instance *dev) switch (dev->phy.speed) { case SPEED_1000: if (emac_phy_gpcs(dev->phy.mode)) { - mr1 |= EMAC_MR1_MF_1000GPCS | - EMAC_MR1_MF_IPPA(dev->phy.address); + mr1 |= EMAC_MR1_MF_1000GPCS | EMAC_MR1_MF_IPPA( + (dev->phy.gpcs_address != 0xffffffff) ? + dev->phy.gpcs_address : dev->phy.address); /* Put some arbitrary OUI, Manuf & Rev IDs so we can * identify this GPCS PHY later. @@ -660,8 +678,12 @@ static int emac_configure(struct emac_instance *dev) out_be32(&p->iser, r); /* We need to take GPCS PHY out of isolate mode after EMAC reset */ - if (emac_phy_gpcs(dev->phy.mode)) - emac_mii_reset_phy(&dev->phy); + if (emac_phy_gpcs(dev->phy.mode)) { + if (dev->phy.gpcs_address != 0xffffffff) + emac_mii_reset_gpcs(&dev->phy); + else + emac_mii_reset_phy(&dev->phy); + } return 0; } @@ -866,7 +888,9 @@ static int emac_mdio_read(struct net_device *ndev, int id, int reg) struct emac_instance *dev = netdev_priv(ndev); int res; - res = __emac_mdio_read(dev->mdio_instance ? dev->mdio_instance : dev, + res = __emac_mdio_read((dev->mdio_instance && + dev->phy.gpcs_address != id) ? + dev->mdio_instance : dev, (u8) id, (u8) reg); return res; } @@ -875,7 +899,9 @@ static void emac_mdio_write(struct net_device *ndev, int id, int reg, int val) { struct emac_instance *dev = netdev_priv(ndev); - __emac_mdio_write(dev->mdio_instance ? dev->mdio_instance : dev, + __emac_mdio_write((dev->mdio_instance && + dev->phy.gpcs_address != id) ? + dev->mdio_instance : dev, (u8) id, (u8) reg, (u16) val); } @@ -2367,7 +2393,11 @@ static int __devinit emac_init_phy(struct emac_instance *dev) * XXX I probably should move these settings to the dev tree */ dev->phy.address = -1; - dev->phy.features = SUPPORTED_100baseT_Full | SUPPORTED_MII; + dev->phy.features = SUPPORTED_MII; + if (emac_phy_supports_gige(dev->phy_mode)) + dev->phy.features |= SUPPORTED_1000baseT_Full; + else + dev->phy.features |= SUPPORTED_100baseT_Full; dev->phy.pause = 1; return 0; @@ -2406,7 +2436,9 @@ static int __devinit emac_init_phy(struct emac_instance *dev) * Note that the busy_phy_map is currently global * while it should probably be per-ASIC... */ - dev->phy.address = dev->cell_index; + dev->phy.gpcs_address = dev->gpcs_address; + if (dev->phy.gpcs_address == 0xffffffff) + dev->phy.address = dev->cell_index; } emac_configure(dev); @@ -2516,6 +2548,8 @@ static int __devinit emac_init_config(struct emac_instance *dev) dev->phy_address = 0xffffffff; if (emac_read_uint_prop(np, "phy-map", &dev->phy_map, 0)) dev->phy_map = 0xffffffff; + if (emac_read_uint_prop(np, "gpcs-address", &dev->gpcs_address, 0)) + dev->gpcs_address = 0xffffffff; if (emac_read_uint_prop(np->parent, "clock-frequency", &dev->opb_bus_freq, 1)) return -ENXIO; if (emac_read_uint_prop(np, "tah-device", &dev->tah_ph, 0)) @@ -2559,6 +2593,9 @@ static int __devinit emac_init_config(struct emac_instance *dev) /* Check EMAC version */ if (of_device_is_compatible(np, "ibm,emac4sync")) { dev->features |= (EMAC_FTR_EMAC4 | EMAC_FTR_EMAC4SYNC); + if (of_device_is_compatible(np, "ibm,emac-460ex") || + of_device_is_compatible(np, "ibm,emac-460gt")) + dev->features |= EMAC_FTR_460EX_PHY_CLK_FIX; } else if (of_device_is_compatible(np, "ibm,emac4")) { dev->features |= EMAC_FTR_EMAC4; if (of_device_is_compatible(np, "ibm,emac-440gx")) @@ -2826,6 +2863,9 @@ static int __devinit emac_probe(struct of_device *ofdev, ndev->dev_addr[0], ndev->dev_addr[1], ndev->dev_addr[2], ndev->dev_addr[3], ndev->dev_addr[4], ndev->dev_addr[5]); + if (dev->phy_mode == PHY_MODE_SGMII) + printk(KERN_NOTICE "%s: in SGMII mode\n", ndev->name); + if (dev->phy.address >= 0) printk("%s: found %s PHY (0x%02x)\n", ndev->name, dev->phy.def->name, dev->phy.address); diff --git a/drivers/net/ibm_newemac/core.h b/drivers/net/ibm_newemac/core.h index 59e5a5d802f..18d56c6c423 100644 --- a/drivers/net/ibm_newemac/core.h +++ b/drivers/net/ibm_newemac/core.h @@ -190,6 +190,9 @@ struct emac_instance { struct delayed_work link_work; int link_polling; + /* GPCS PHY infos */ + u32 gpcs_address; + /* Shared MDIO if any */ u32 mdio_ph; struct of_device *mdio_dev; @@ -317,6 +320,10 @@ struct emac_instance { * The 405EX and 460EX contain the EMAC4SYNC core */ #define EMAC_FTR_EMAC4SYNC 0x00000200 +/* + * Set if we need phy clock workaround for 460ex or 460gt + */ +#define EMAC_FTR_460EX_PHY_CLK_FIX 0x00000400 /* Right now, we don't quite handle the always/possible masks on the @@ -344,6 +351,7 @@ enum { #ifdef CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL EMAC_FTR_NO_FLOW_CONTROL_40x | #endif + EMAC_FTR_460EX_PHY_CLK_FIX | EMAC_FTR_440EP_PHY_CLK_FIX, }; diff --git a/drivers/net/ibm_newemac/phy.c b/drivers/net/ibm_newemac/phy.c index 37bfeea8788..606db53ef78 100644 --- a/drivers/net/ibm_newemac/phy.c +++ b/drivers/net/ibm_newemac/phy.c @@ -38,6 +38,16 @@ static inline void phy_write(struct mii_phy *phy, int reg, int val) phy->mdio_write(phy->dev, phy->address, reg, val); } +static inline int gpcs_phy_read(struct mii_phy *phy, int reg) +{ + return phy->mdio_read(phy->dev, phy->gpcs_address, reg); +} + +static inline void gpcs_phy_write(struct mii_phy *phy, int reg, int val) +{ + phy->mdio_write(phy->dev, phy->gpcs_address, reg, val); +} + int emac_mii_reset_phy(struct mii_phy *phy) { int val; @@ -62,6 +72,37 @@ int emac_mii_reset_phy(struct mii_phy *phy) return limit <= 0; } +int emac_mii_reset_gpcs(struct mii_phy *phy) +{ + int val; + int limit = 10000; + + val = gpcs_phy_read(phy, MII_BMCR); + val &= ~(BMCR_ISOLATE | BMCR_ANENABLE); + val |= BMCR_RESET; + gpcs_phy_write(phy, MII_BMCR, val); + + udelay(300); + + while (limit--) { + val = gpcs_phy_read(phy, MII_BMCR); + if (val >= 0 && (val & BMCR_RESET) == 0) + break; + udelay(10); + } + if ((val & BMCR_ISOLATE) && limit > 0) + gpcs_phy_write(phy, MII_BMCR, val & ~BMCR_ISOLATE); + + if (limit > 0 && phy->mode == PHY_MODE_SGMII) { + /* Configure GPCS interface to recommended setting for SGMII */ + gpcs_phy_write(phy, 0x04, 0x8120); /* AsymPause, FDX */ + gpcs_phy_write(phy, 0x07, 0x2801); /* msg_pg, toggle */ + gpcs_phy_write(phy, 0x00, 0x0140); /* 1Gbps, FDX */ + } + + return limit <= 0; +} + static int genmii_setup_aneg(struct mii_phy *phy, u32 advertise) { int ctl, adv; @@ -332,6 +373,33 @@ static int m88e1111_init(struct mii_phy *phy) return 0; } +static int m88e1112_init(struct mii_phy *phy) +{ + /* + * Marvell 88E1112 PHY needs to have the SGMII MAC + * interace (page 2) properly configured to + * communicate with the 460EX/GT GPCS interface. + */ + + u16 reg_short; + + pr_debug("%s: Marvell 88E1112 Ethernet\n", __func__); + + /* Set access to Page 2 */ + phy_write(phy, 0x16, 0x0002); + + phy_write(phy, 0x00, 0x0040); /* 1Gbps */ + reg_short = (u16)(phy_read(phy, 0x1a)); + reg_short |= 0x8000; /* bypass Auto-Negotiation */ + phy_write(phy, 0x1a, reg_short); + emac_mii_reset_phy(phy); /* reset MAC interface */ + + /* Reset access to Page 0 */ + phy_write(phy, 0x16, 0x0000); + + return 0; +} + static int et1011c_init(struct mii_phy *phy) { u16 reg_short; @@ -384,11 +452,27 @@ static struct mii_phy_def m88e1111_phy_def = { .ops = &m88e1111_phy_ops, }; +static struct mii_phy_ops m88e1112_phy_ops = { + .init = m88e1112_init, + .setup_aneg = genmii_setup_aneg, + .setup_forced = genmii_setup_forced, + .poll_link = genmii_poll_link, + .read_link = genmii_read_link +}; + +static struct mii_phy_def m88e1112_phy_def = { + .phy_id = 0x01410C90, + .phy_id_mask = 0x0ffffff0, + .name = "Marvell 88E1112 Ethernet", + .ops = &m88e1112_phy_ops, +}; + static struct mii_phy_def *mii_phy_table[] = { &et1011c_phy_def, &cis8201_phy_def, &bcm5248_phy_def, &m88e1111_phy_def, + &m88e1112_phy_def, &genmii_phy_def, NULL }; diff --git a/drivers/net/ibm_newemac/phy.h b/drivers/net/ibm_newemac/phy.h index 1b65c81f655..5d2bf4cbe50 100644 --- a/drivers/net/ibm_newemac/phy.h +++ b/drivers/net/ibm_newemac/phy.h @@ -57,6 +57,7 @@ struct mii_phy { or determined automaticaly */ int address; /* PHY address */ int mode; /* PHY mode */ + int gpcs_address; /* GPCS PHY address */ /* 1: autoneg enabled, 0: disabled */ int autoneg; @@ -81,5 +82,6 @@ struct mii_phy { */ int emac_mii_phy_probe(struct mii_phy *phy, int address); int emac_mii_reset_phy(struct mii_phy *phy); +int emac_mii_reset_gpcs(struct mii_phy *phy); #endif /* __IBM_NEWEMAC_PHY_H */ -- cgit v1.2.3 From e00de30a9decf48793ac83173144884a1f33de82 Mon Sep 17 00:00:00 2001 From: Victor Gallardo Date: Wed, 1 Oct 2008 23:29:06 -0700 Subject: powerpc/44x: Add AMCC Arches eval board support The Arches Evaluation board is based on the AMCC 460GT SoC chip. This board is a dual processor board with each processor providing independent resources for Rapid IO, Gigabit Ethernet, and serial communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR FLASH, UART, EEPROM and temperature sensor, along with a shared debug port. The two 460GT's will communicate with each other via shared memory, Gigabit Ethernet and x1 PCI-Express. Signed-off-by: Victor Gallardo Signed-off-by: Josh Boyer --- arch/powerpc/platforms/44x/Kconfig | 17 +++++++++++++++-- arch/powerpc/platforms/44x/ppc44x_simple.c | 3 ++- 2 files changed, 17 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig index f8ef279f325..79c1154f88d 100644 --- a/arch/powerpc/platforms/44x/Kconfig +++ b/arch/powerpc/platforms/44x/Kconfig @@ -81,6 +81,17 @@ config WARP See http://www.pikatechnologies.com/ and follow the "PIKA for Computer Telephony Developers" link for more information. +config ARCHES + bool "Arches" + depends on 44x + default n + select PPC44x_SIMPLE + select 460EX # Odd since it uses 460GT but the effects are the same + select PCI + select PPC4xx_PCI_EXPRESS + help + This option enables support for the AMCC Dual PPC460GT evaluation board. + config CANYONLANDS bool "Canyonlands" depends on 44x @@ -89,6 +100,8 @@ config CANYONLANDS select 460EX select PCI select PPC4xx_PCI_EXPRESS + select IBM_NEW_EMAC_RGMII + select IBM_NEW_EMAC_ZMII help This option enables support for the AMCC PPC460EX evaluation board. @@ -100,6 +113,8 @@ config GLACIER select 460EX # Odd since it uses 460GT but the effects are the same select PCI select PPC4xx_PCI_EXPRESS + select IBM_NEW_EMAC_RGMII + select IBM_NEW_EMAC_ZMII help This option enables support for the AMCC PPC460GT evaluation board. @@ -195,8 +210,6 @@ config 460EX bool select PPC_FPU select IBM_NEW_EMAC_EMAC4 - select IBM_NEW_EMAC_RGMII - select IBM_NEW_EMAC_ZMII select IBM_NEW_EMAC_TAH # 44x errata/workaround config symbols, selected by the CPU models above diff --git a/arch/powerpc/platforms/44x/ppc44x_simple.c b/arch/powerpc/platforms/44x/ppc44x_simple.c index 57e71203d0f..29671262801 100644 --- a/arch/powerpc/platforms/44x/ppc44x_simple.c +++ b/arch/powerpc/platforms/44x/ppc44x_simple.c @@ -50,8 +50,9 @@ machine_device_initcall(ppc44x_simple, ppc44x_device_probe); * board.c file for it rather than adding it to this list. */ static char *board[] __initdata = { + "amcc,arches", "amcc,bamboo", - "amcc,cayonlands", + "amcc,canyonlands", "amcc,glacier", "ibm,ebony", "amcc,katmai", -- cgit v1.2.3 From e9ee2924ddd86ca7c97d8a8770069d2c6035d349 Mon Sep 17 00:00:00 2001 From: Victor Gallardo Date: Wed, 1 Oct 2008 23:29:16 -0700 Subject: powerpc/44x: Add AMCC Arches DTS Basic functionality for the AMCC Arches eval Board. Signed-off-by: Victor Gallardo Signed-off-by: Josh Boyer --- arch/powerpc/boot/dts/arches.dts | 293 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 293 insertions(+) create mode 100644 arch/powerpc/boot/dts/arches.dts (limited to 'arch') diff --git a/arch/powerpc/boot/dts/arches.dts b/arch/powerpc/boot/dts/arches.dts new file mode 100644 index 00000000000..d9113b1e8c1 --- /dev/null +++ b/arch/powerpc/boot/dts/arches.dts @@ -0,0 +1,293 @@ +/* + * Device Tree Source for AMCC Arches (dual 460GT board) + * + * (C) Copyright 2008 Applied Micro Circuits Corporation + * Victor Gallardo + * Adam Graham + * + * Based on the glacier.dts file + * Stefan Roese + * Copyright 2008 DENX Software Engineering + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/dts-v1/; + +/ { + #address-cells = <2>; + #size-cells = <1>; + model = "amcc,arches"; + compatible = "amcc,arches"; + dcr-parent = <&{/cpus/cpu@0}>; + + aliases { + ethernet0 = &EMAC0; + ethernet1 = &EMAC1; + ethernet2 = &EMAC2; + serial0 = &UART0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + model = "PowerPC,460GT"; + reg = <0x00000000>; + clock-frequency = <0>; /* Filled in by U-Boot */ + timebase-frequency = <0>; /* Filled in by U-Boot */ + i-cache-line-size = <32>; + d-cache-line-size = <32>; + i-cache-size = <32768>; + d-cache-size = <32768>; + dcr-controller; + dcr-access-method = "native"; + }; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x00000000 0x00000000>; /* Filled in by U-Boot */ + }; + + UIC0: interrupt-controller0 { + compatible = "ibm,uic-460gt","ibm,uic"; + interrupt-controller; + cell-index = <0>; + dcr-reg = <0x0c0 0x009>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + }; + + UIC1: interrupt-controller1 { + compatible = "ibm,uic-460gt","ibm,uic"; + interrupt-controller; + cell-index = <1>; + dcr-reg = <0x0d0 0x009>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + interrupts = <0x1e 0x4 0x1f 0x4>; /* cascade */ + interrupt-parent = <&UIC0>; + }; + + UIC2: interrupt-controller2 { + compatible = "ibm,uic-460gt","ibm,uic"; + interrupt-controller; + cell-index = <2>; + dcr-reg = <0x0e0 0x009>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + interrupts = <0xa 0x4 0xb 0x4>; /* cascade */ + interrupt-parent = <&UIC0>; + }; + + UIC3: interrupt-controller3 { + compatible = "ibm,uic-460gt","ibm,uic"; + interrupt-controller; + cell-index = <3>; + dcr-reg = <0x0f0 0x009>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + interrupts = <0x10 0x4 0x11 0x4>; /* cascade */ + interrupt-parent = <&UIC0>; + }; + + SDR0: sdr { + compatible = "ibm,sdr-460gt"; + dcr-reg = <0x00e 0x002>; + }; + + CPR0: cpr { + compatible = "ibm,cpr-460gt"; + dcr-reg = <0x00c 0x002>; + }; + + plb { + compatible = "ibm,plb-460gt", "ibm,plb4"; + #address-cells = <2>; + #size-cells = <1>; + ranges; + clock-frequency = <0>; /* Filled in by U-Boot */ + + SDRAM0: sdram { + compatible = "ibm,sdram-460gt", "ibm,sdram-405gp"; + dcr-reg = <0x010 0x002>; + }; + + MAL0: mcmal { + compatible = "ibm,mcmal-460gt", "ibm,mcmal2"; + dcr-reg = <0x180 0x062>; + num-tx-chans = <3>; + num-rx-chans = <24>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-parent = <&UIC2>; + interrupts = < /*TXEOB*/ 0x6 0x4 + /*RXEOB*/ 0x7 0x4 + /*SERR*/ 0x3 0x4 + /*TXDE*/ 0x4 0x4 + /*RXDE*/ 0x5 0x4>; + desc-base-addr-high = <0x8>; + }; + + POB0: opb { + compatible = "ibm,opb-460gt", "ibm,opb"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0xb0000000 0x00000004 0xb0000000 0x50000000>; + clock-frequency = <0>; /* Filled in by U-Boot */ + + EBC0: ebc { + compatible = "ibm,ebc-460gt", "ibm,ebc"; + dcr-reg = <0x012 0x002>; + #address-cells = <2>; + #size-cells = <1>; + clock-frequency = <0>; /* Filled in by U-Boot */ + /* ranges property is supplied by U-Boot */ + interrupts = <0x6 0x4>; + interrupt-parent = <&UIC1>; + }; + + UART0: serial@ef600300 { + device_type = "serial"; + compatible = "ns16550"; + reg = <0xef600300 0x00000008>; + virtual-reg = <0xef600300>; + clock-frequency = <0>; /* Filled in by U-Boot */ + current-speed = <0>; /* Filled in by U-Boot */ + interrupt-parent = <&UIC1>; + interrupts = <0x1 0x4>; + }; + + IIC0: i2c@ef600700 { + compatible = "ibm,iic-460gt", "ibm,iic"; + reg = <0xef600700 0x00000014>; + interrupt-parent = <&UIC0>; + interrupts = <0x2 0x4>; + }; + + IIC1: i2c@ef600800 { + compatible = "ibm,iic-460gt", "ibm,iic"; + reg = <0xef600800 0x00000014>; + interrupt-parent = <&UIC0>; + interrupts = <0x3 0x4>; + }; + + TAH0: emac-tah@ef601350 { + compatible = "ibm,tah-460gt", "ibm,tah"; + reg = <0xef601350 0x00000030>; + }; + + TAH1: emac-tah@ef601450 { + compatible = "ibm,tah-460gt", "ibm,tah"; + reg = <0xef601450 0x00000030>; + }; + + EMAC0: ethernet@ef600e00 { + device_type = "network"; + compatible = "ibm,emac-460gt", "ibm,emac4sync"; + interrupt-parent = <&EMAC0>; + interrupts = <0x0 0x1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = ; + reg = <0xef600e00 0x000000c4>; + local-mac-address = [000000000000]; /* Filled in by U-Boot */ + mal-device = <&MAL0>; + mal-tx-channel = <0>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <9000>; + rx-fifo-size = <4096>; + tx-fifo-size = <2048>; + phy-mode = "sgmii"; + phy-map = <0xffffffff>; + gpcs-address = <0x0000000a>; + tah-device = <&TAH0>; + tah-channel = <0>; + has-inverted-stacr-oc; + has-new-stacr-staopc; + }; + + EMAC1: ethernet@ef600f00 { + device_type = "network"; + compatible = "ibm,emac-460gt", "ibm,emac4sync"; + interrupt-parent = <&EMAC1>; + interrupts = <0x0 0x1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = ; + reg = <0xef600f00 0x000000c4>; + local-mac-address = [000000000000]; /* Filled in by U-Boot */ + mal-device = <&MAL0>; + mal-tx-channel = <1>; + mal-rx-channel = <8>; + cell-index = <1>; + max-frame-size = <9000>; + rx-fifo-size = <4096>; + tx-fifo-size = <2048>; + phy-mode = "sgmii"; + phy-map = <0x00000000>; + gpcs-address = <0x0000000b>; + tah-device = <&TAH1>; + tah-channel = <1>; + has-inverted-stacr-oc; + has-new-stacr-staopc; + mdio-device = <&EMAC0>; + }; + + EMAC2: ethernet@ef601100 { + device_type = "network"; + compatible = "ibm,emac-460gt", "ibm,emac4sync"; + interrupt-parent = <&EMAC2>; + interrupts = <0x0 0x1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = ; + reg = <0xef601100 0x000000c4>; + local-mac-address = [000000000000]; /* Filled in by U-Boot */ + mal-device = <&MAL0>; + mal-tx-channel = <2>; + mal-rx-channel = <16>; + cell-index = <2>; + max-frame-size = <9000>; + rx-fifo-size = <4096>; + tx-fifo-size = <2048>; + phy-mode = "sgmii"; + phy-map = <0x00000001>; + gpcs-address = <0x0000000C>; + has-inverted-stacr-oc; + has-new-stacr-staopc; + mdio-device = <&EMAC0>; + }; + }; + }; +}; -- cgit v1.2.3 From 3d5fa877bdf65451c78c3b3d581355deea403b80 Mon Sep 17 00:00:00 2001 From: Victor Gallardo Date: Wed, 1 Oct 2008 23:29:26 -0700 Subject: powerpc/44x: Add AMCC Arches defconfig file Add a defconfig for the AMCC Arches evaluation board Signed-off-by: Victor Gallardo Signed-off-by: Josh Boyer --- arch/powerpc/configs/44x/arches_defconfig | 767 ++++++++++++++++++++++++++++++ 1 file changed, 767 insertions(+) create mode 100644 arch/powerpc/configs/44x/arches_defconfig (limited to 'arch') diff --git a/arch/powerpc/configs/44x/arches_defconfig b/arch/powerpc/configs/44x/arches_defconfig new file mode 100644 index 00000000000..70f46078eb6 --- /dev/null +++ b/arch/powerpc/configs/44x/arches_defconfig @@ -0,0 +1,767 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.27-rc5 +# Wed Oct 1 15:54:57 2008 +# +# CONFIG_PPC64 is not set + +# +# Processor support +# +# CONFIG_6xx is not set +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_8xx is not set +# CONFIG_40x is not set +CONFIG_44x=y +# CONFIG_E200 is not set +CONFIG_PPC_FPU=y +CONFIG_4xx=y +CONFIG_BOOKE=y +CONFIG_PTE_64BIT=y +CONFIG_PHYS_64BIT=y +# CONFIG_PPC_MM_SLICES is not set +CONFIG_NOT_COHERENT_CACHE=y +CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set +CONFIG_IRQ_PER_CPU=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +# CONFIG_ARCH_NO_VIRT_TO_BUS is not set +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_OF=y +CONFIG_PPC_UDBG_16550=y +# CONFIG_GENERIC_TBSYNC is not set +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +# CONFIG_DEFAULT_UIMAGE is not set +CONFIG_PPC_DCR_NATIVE=y +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_PPC_DCR=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLUB_DEBUG=y +# CONFIG_SLAB is not set +CONFIG_SLUB=y +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +# CONFIG_HAVE_CLK is not set +CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +CONFIG_LBD=y +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_CLASSIC_RCU=y +CONFIG_PPC4xx_PCI_EXPRESS=y + +# +# Platform support +# +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PQ2ADS is not set +# CONFIG_BAMBOO is not set +# CONFIG_EBONY is not set +# CONFIG_SAM440EP is not set +# CONFIG_SEQUOIA is not set +# CONFIG_TAISHAN is not set +# CONFIG_KATMAI is not set +# CONFIG_RAINIER is not set +# CONFIG_WARP is not set +CONFIG_ARCHES=y +# CONFIG_CANYONLANDS is not set +# CONFIG_GLACIER is not set +# CONFIG_YOSEMITE is not set +# CONFIG_XILINX_VIRTEX440_GENERIC_BOARD is not set +CONFIG_PPC44x_SIMPLE=y +CONFIG_460EX=y +# CONFIG_IPIC is not set +# CONFIG_MPIC is not set +# CONFIG_MPIC_WEIRD is not set +# CONFIG_PPC_I8259 is not set +# CONFIG_PPC_RTAS is not set +# CONFIG_MMIO_NVRAM is not set +# CONFIG_PPC_MPC106 is not set +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +# CONFIG_FSL_ULI1575 is not set + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +CONFIG_SCHED_HRTICK=y +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +# CONFIG_MATH_EMULATION is not set +# CONFIG_IOMMU_HELPER is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_HAS_WALK_MEMORY=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y +CONFIG_RESOURCES_64BIT=y +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_FORCE_MAX_ZONEORDER=11 +CONFIG_PROC_DEVICETREE=y +CONFIG_CMDLINE_BOOL=y +CONFIG_CMDLINE="" +CONFIG_EXTRA_TARGETS="" +CONFIG_SECCOMP=y +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +CONFIG_ZONE_DMA=y +CONFIG_PPC_INDIRECT_PCI=y +CONFIG_4xx_SOC=y +CONFIG_PPC_PCI_CHOICE=y +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_SYSCALL=y +# CONFIG_PCIEPORTBUS is not set +CONFIG_ARCH_SUPPORTS_MSI=y +# CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y +# CONFIG_PCI_DEBUG is not set +# CONFIG_PCCARD is not set +# CONFIG_HOTPLUG_PCI is not set +# CONFIG_HAS_RAPIDIO is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_PAGE_OFFSET=0xc0000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_PHYSICAL_START=0x00000000 +CONFIG_TASK_SIZE=0xc0000000 +CONFIG_CONSISTENT_START=0xff100000 +CONFIG_CONSISTENT_SIZE=0x00200000 +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +CONFIG_CONNECTOR=y +CONFIG_PROC_EVENTS=y +# CONFIG_MTD is not set +CONFIG_OF_DEVICE=y +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=35000 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_XILINX_SYSACE is not set +# CONFIG_BLK_DEV_HD is not set +# CONFIG_MISC_DEVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# Enable only one of the two stacks, unless you know what you are doing +# +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set +# CONFIG_I2O is not set +# CONFIG_MACINTOSH_DRIVERS is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y +# CONFIG_MII is not set +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +CONFIG_IBM_NEW_EMAC=y +CONFIG_IBM_NEW_EMAC_RXB=256 +CONFIG_IBM_NEW_EMAC_TXB=256 +CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32 +CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256 +CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0 +# CONFIG_IBM_NEW_EMAC_DEBUG is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +CONFIG_IBM_NEW_EMAC_TAH=y +CONFIG_IBM_NEW_EMAC_EMAC4=y +# CONFIG_NET_PCI is not set +# CONFIG_B44 is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +# CONFIG_INPUT is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +# CONFIG_SERIAL_8250_PCI is not set +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +# CONFIG_SERIAL_8250_MANY_PORTS is not set +CONFIG_SERIAL_8250_SHARE_IRQ=y +# CONFIG_SERIAL_8250_DETECT_IRQ is not set +# CONFIG_SERIAL_8250_RSA is not set + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_NVRAM is not set +# CONFIG_GEN_RTC is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +# CONFIG_I2C is not set +# CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +CONFIG_DAB=y + +# +# Graphics support +# +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set +# CONFIG_SOUND is not set +# CONFIG_USB_SUPPORT is not set +# CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +# CONFIG_INFINIBAND is not set +# CONFIG_EDAC is not set +# CONFIG_RTC_CLASS is not set +# CONFIG_DMADEVICES is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_NLS is not set +# CONFIG_DLM is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_HAVE_LMB=y + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_SLUB_STATS is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_HAVE_FTRACE=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +# CONFIG_FTRACE is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_MSI_BITMAP_SELFTEST is not set +# CONFIG_XMON is not set +# CONFIG_IRQSTACKS is not set +# CONFIG_VIRQ_DEBUG is not set +# CONFIG_BDI_SWITCH is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +# CONFIG_CRYPTO is not set +# CONFIG_PPC_CLOCK is not set +# CONFIG_VIRTUALIZATION is not set -- cgit v1.2.3 From 6ddc9d3200c25edddd7051f208dbbdd8e16f0734 Mon Sep 17 00:00:00 2001 From: Sebastien Dugue Date: Sun, 14 Sep 2008 21:50:18 +0000 Subject: powerpc: Ignore generated vmlinux.lds in git Add a .gitignore in arch/powerpc/kernel to ignore the generated vmlinux.lds. Signed-off-by: Sebastien Dugue Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/.gitignore | 1 + 1 file changed, 1 insertion(+) create mode 100644 arch/powerpc/kernel/.gitignore (limited to 'arch') diff --git a/arch/powerpc/kernel/.gitignore b/arch/powerpc/kernel/.gitignore new file mode 100644 index 00000000000..c5f676c3c22 --- /dev/null +++ b/arch/powerpc/kernel/.gitignore @@ -0,0 +1 @@ +vmlinux.lds -- cgit v1.2.3 From a880e7623397bcb44877b012cd65baa11ad1bbf8 Mon Sep 17 00:00:00 2001 From: Roland Dreier Date: Mon, 15 Sep 2008 10:43:35 +0000 Subject: powerpc: Avoid integer overflow in page_is_ram() Commit 8b150478 ("ppc: make phys_mem_access_prot() work with pfns instead of addresses") fixed page_is_ram() in arch/ppc to avoid overflow for addresses above 4G on 32-bit kernels. However arch/powerpc's page_is_ram() is missing the same fix -- it computes a physical address by doing pfn << PAGE_SHIFT, which overflows if pfn corresponds to a page above 4G. In particular this causes pages above 4G to be mapped with the wrong caching attribute; for example many ppc440-based SoCs have PCI space above 4G, and mmap()ing MMIO space may end up with a mapping that has caching enabled. Fix this by working with the pfn and avoiding the conversion to physical address that causes the overflow. This patch compares the pfn to max_pfn, which is a semantic change from the old code -- that code compared the physical address to high_memory, which corresponds to max_low_pfn. However, I think that was is another bug, since highmem pages are still RAM. Reported-by: vb Signed-off-by: Roland Dreier Acked-by: Benjamin Herrenschmidt Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/mm/mem.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/mm/mem.c b/arch/powerpc/mm/mem.c index 1c93c255873..98d7bf99533 100644 --- a/arch/powerpc/mm/mem.c +++ b/arch/powerpc/mm/mem.c @@ -75,11 +75,10 @@ static inline pte_t *virt_to_kpte(unsigned long vaddr) int page_is_ram(unsigned long pfn) { - unsigned long paddr = (pfn << PAGE_SHIFT); - #ifndef CONFIG_PPC64 /* XXX for now */ - return paddr < __pa(high_memory); + return pfn < max_pfn; #else + unsigned long paddr = (pfn << PAGE_SHIFT); int i; for (i=0; i < lmb.memory.cnt; i++) { unsigned long base; -- cgit v1.2.3 From 2e2b4043cc0a2c11abbe4fdff6dce3f81cff3e30 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Wed, 24 Sep 2008 04:01:09 +0000 Subject: powerpc: Fix 64-bit hibernation with 64k pages A bug in my initial 64-bit hibernation code breaks it when using page sizes that aren't 4K. Signed-off-by: Johannes Berg Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/swsusp_asm64.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/swsusp_asm64.S b/arch/powerpc/kernel/swsusp_asm64.S index e092c3cbdb9..86ac1d90d02 100644 --- a/arch/powerpc/kernel/swsusp_asm64.S +++ b/arch/powerpc/kernel/swsusp_asm64.S @@ -133,7 +133,7 @@ END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC) cmpdi r12,0 beq- nothing_to_copy - li r15,512 + li r15,PAGE_SIZE>>3 copyloop: ld r13,pbe_address(r12) ld r14,pbe_orig_address(r12) -- cgit v1.2.3 From ebe40c5c4c888f2cbfd9f0880a8bc072e6fc3a0d Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Wed, 24 Sep 2008 04:29:08 +0000 Subject: powerpc: Enforce sane MAX_ORDER powerpc uses CONFIG_FORCE_MAX_ZONEORDER, and some things depend on it being at least 10 when 64k pages are not configured (notably the dart iommu code with CONFIG_PM). The defaults are fine, but when going from a 64K pages config to one without 64K pages, MAX_ORDER stays at 9 which is too low for 4K pages. This patch makes the Kconfig enforce at least the defaults. Signed-off-by: Johannes Berg Acked-by: Timur Tabi Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/Kconfig | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig index 17c988b678d..c171f5bcf25 100644 --- a/arch/powerpc/Kconfig +++ b/arch/powerpc/Kconfig @@ -415,8 +415,11 @@ config PPC_64K_PAGES config FORCE_MAX_ZONEORDER int "Maximum zone order" + range 9 64 if PPC_64K_PAGES default "9" if PPC_64K_PAGES + range 13 64 if PPC64 && !PPC_64K_PAGES default "13" if PPC64 && !PPC_64K_PAGES + range 11 64 default "11" help The kernel memory allocator divides physically contiguous memory -- cgit v1.2.3 From 3396c72b92efd16bca16490a72277b3a494e0f0e Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Fri, 26 Sep 2008 07:19:46 +0000 Subject: powerpc: Remove CHRP and PMAC support from FSL defconfigs Fix various defconfigs for Freescale chip based boards to remove CONFIG_PPC_PMAC or CONFIG_PPC_CHRP which crept in due to those being default y Signed-off-by: Timur Tabi Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/configs/83xx/asp8347_defconfig | 2 -- arch/powerpc/configs/83xx/mpc8313_rdb_defconfig | 2 -- arch/powerpc/configs/83xx/mpc8315_rdb_defconfig | 2 -- arch/powerpc/configs/83xx/mpc832x_mds_defconfig | 2 -- arch/powerpc/configs/83xx/mpc832x_rdb_defconfig | 2 -- arch/powerpc/configs/83xx/mpc834x_itx_defconfig | 2 -- arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig | 2 -- arch/powerpc/configs/83xx/mpc834x_mds_defconfig | 2 -- arch/powerpc/configs/83xx/mpc836x_mds_defconfig | 2 -- arch/powerpc/configs/83xx/mpc836x_rdk_defconfig | 2 -- arch/powerpc/configs/83xx/mpc837x_mds_defconfig | 2 -- arch/powerpc/configs/83xx/mpc837x_rdb_defconfig | 2 -- arch/powerpc/configs/83xx/sbc834x_defconfig | 2 -- arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig | 2 -- arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig | 2 -- arch/powerpc/configs/86xx/sbc8641d_defconfig | 2 -- arch/powerpc/configs/ep8248e_defconfig | 2 -- arch/powerpc/configs/mpc8272_ads_defconfig | 2 -- arch/powerpc/configs/mpc83xx_defconfig | 2 -- arch/powerpc/configs/pq2fads_defconfig | 2 -- 20 files changed, 40 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/configs/83xx/asp8347_defconfig b/arch/powerpc/configs/83xx/asp8347_defconfig index 5e6780a088c..6638f5a03a7 100644 --- a/arch/powerpc/configs/83xx/asp8347_defconfig +++ b/arch/powerpc/configs/83xx/asp8347_defconfig @@ -164,11 +164,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig b/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig index 2028337868b..df125f30fae 100644 --- a/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig @@ -163,11 +163,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig b/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig index dd80eb0a87a..6e0e08cf0b0 100644 --- a/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig @@ -163,11 +163,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc832x_mds_defconfig b/arch/powerpc/configs/83xx/mpc832x_mds_defconfig index bdf50c8a17e..d6e204a7b26 100644 --- a/arch/powerpc/configs/83xx/mpc832x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc832x_mds_defconfig @@ -163,11 +163,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig b/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig index 4eef8c95480..1f3d3434b29 100644 --- a/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig @@ -163,11 +163,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc834x_itx_defconfig b/arch/powerpc/configs/83xx/mpc834x_itx_defconfig index 8d651393185..4686c2151d0 100644 --- a/arch/powerpc/configs/83xx/mpc834x_itx_defconfig +++ b/arch/powerpc/configs/83xx/mpc834x_itx_defconfig @@ -163,11 +163,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig b/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig index a8afa39d6f7..f11c25ecef7 100644 --- a/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig +++ b/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig @@ -163,11 +163,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc834x_mds_defconfig b/arch/powerpc/configs/83xx/mpc834x_mds_defconfig index 24c320a3667..ffe4b2ef969 100644 --- a/arch/powerpc/configs/83xx/mpc834x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc834x_mds_defconfig @@ -163,11 +163,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc836x_mds_defconfig b/arch/powerpc/configs/83xx/mpc836x_mds_defconfig index cf2706a5f34..71445e31a30 100644 --- a/arch/powerpc/configs/83xx/mpc836x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc836x_mds_defconfig @@ -163,11 +163,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig b/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig index 7d674be702f..58486ccae46 100644 --- a/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig +++ b/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig @@ -164,11 +164,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc837x_mds_defconfig b/arch/powerpc/configs/83xx/mpc837x_mds_defconfig index de472022aa8..0171e217645 100644 --- a/arch/powerpc/configs/83xx/mpc837x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc837x_mds_defconfig @@ -164,11 +164,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig b/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig index e8d2d691d26..d6b383bb364 100644 --- a/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig @@ -164,11 +164,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/83xx/sbc834x_defconfig b/arch/powerpc/configs/83xx/sbc834x_defconfig index 9245a67da20..b8dd17bf040 100644 --- a/arch/powerpc/configs/83xx/sbc834x_defconfig +++ b/arch/powerpc/configs/83xx/sbc834x_defconfig @@ -162,11 +162,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig b/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig index 1a9990731eb..14116a80c7c 100644 --- a/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig +++ b/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig @@ -165,11 +165,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig b/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig index ea09be31b6e..07e369d9e48 100644 --- a/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig +++ b/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig @@ -167,11 +167,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/86xx/sbc8641d_defconfig b/arch/powerpc/configs/86xx/sbc8641d_defconfig index f545421f985..3326303d376 100644 --- a/arch/powerpc/configs/86xx/sbc8641d_defconfig +++ b/arch/powerpc/configs/86xx/sbc8641d_defconfig @@ -166,11 +166,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/ep8248e_defconfig b/arch/powerpc/configs/ep8248e_defconfig index ef0c6e80050..a63cd05ef20 100644 --- a/arch/powerpc/configs/ep8248e_defconfig +++ b/arch/powerpc/configs/ep8248e_defconfig @@ -150,11 +150,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set CONFIG_PPC_82xx=y diff --git a/arch/powerpc/configs/mpc8272_ads_defconfig b/arch/powerpc/configs/mpc8272_ads_defconfig index 7c435c84c87..ddbca3e39ba 100644 --- a/arch/powerpc/configs/mpc8272_ads_defconfig +++ b/arch/powerpc/configs/mpc8272_ads_defconfig @@ -151,11 +151,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set CONFIG_PPC_82xx=y diff --git a/arch/powerpc/configs/mpc83xx_defconfig b/arch/powerpc/configs/mpc83xx_defconfig index 916e3df7cc4..994a4e7257f 100644 --- a/arch/powerpc/configs/mpc83xx_defconfig +++ b/arch/powerpc/configs/mpc83xx_defconfig @@ -166,11 +166,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PPC_82xx is not set diff --git a/arch/powerpc/configs/pq2fads_defconfig b/arch/powerpc/configs/pq2fads_defconfig index b390b747664..e687cc0f2a9 100644 --- a/arch/powerpc/configs/pq2fads_defconfig +++ b/arch/powerpc/configs/pq2fads_defconfig @@ -152,11 +152,9 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y -CONFIG_PPC_CHRP=y # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set CONFIG_PPC_82xx=y -- cgit v1.2.3 From 76c31f239ea221a6c84bd26141262a43bfe8b7f4 Mon Sep 17 00:00:00 2001 From: Vitaly Mayatskikh Date: Sun, 28 Sep 2008 23:24:33 +0000 Subject: powerpc: Honor O_NONBLOCK flag when reading RTAS log rtas_log_read() doesn't check file flags for O_NONBLOCK and blocks non-blocking readers of /proc/ppc64/rtas/error_log when there is no data available. This fixes it. Also rtas_log_read() returns now with ENODATA to prevent suspending of process in wait_event_interruptible() when logging facility was switched off and log is already empty. Signed-off-by: Vitaly Mayatskikh Acked-by: David Howells Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/rtasd.c | 26 ++++++++++++++++++-------- 1 file changed, 18 insertions(+), 8 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/rtasd.c b/arch/powerpc/platforms/pseries/rtasd.c index c9ffd8c225f..f4e55be2eea 100644 --- a/arch/powerpc/platforms/pseries/rtasd.c +++ b/arch/powerpc/platforms/pseries/rtasd.c @@ -295,19 +295,29 @@ static ssize_t rtas_log_read(struct file * file, char __user * buf, if (!tmp) return -ENOMEM; - spin_lock_irqsave(&rtasd_log_lock, s); /* if it's 0, then we know we got the last one (the one in NVRAM) */ - if (rtas_log_size == 0 && logging_enabled) - nvram_clear_error_log(); - spin_unlock_irqrestore(&rtasd_log_lock, s); + while (rtas_log_size == 0) { + if (file->f_flags & O_NONBLOCK) { + spin_unlock_irqrestore(&rtasd_log_lock, s); + error = -EAGAIN; + goto out; + } + if (!logging_enabled) { + spin_unlock_irqrestore(&rtasd_log_lock, s); + error = -ENODATA; + goto out; + } + nvram_clear_error_log(); - error = wait_event_interruptible(rtas_log_wait, rtas_log_size); - if (error) - goto out; + spin_unlock_irqrestore(&rtasd_log_lock, s); + error = wait_event_interruptible(rtas_log_wait, rtas_log_size); + if (error) + goto out; + spin_lock_irqsave(&rtasd_log_lock, s); + } - spin_lock_irqsave(&rtasd_log_lock, s); offset = rtas_error_log_buffer_max * (rtas_log_start & LOG_NUMBER_MASK); memcpy(tmp, &rtas_log_buf[offset], count); -- cgit v1.2.3 From 7c12d906f4ef690c65e60111375856640f63a545 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Wed, 1 Oct 2008 15:30:04 +0000 Subject: powerpc: Fix sysfs pci mmap on 32-bit machines with 64-bit PCI When manipulating 64-bit PCI addresses, the code would lose the top 32-bit in a couple of places when shifting a pfn due to missing type casting from the 32-bit pfn to a 64-bit resource before the shift. This breaks using newer X servers for example on 440 machines with the PCI bus above 32-bit. Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/pci-common.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/pci-common.c b/arch/powerpc/kernel/pci-common.c index 52ccfed416a..8c0270929cc 100644 --- a/arch/powerpc/kernel/pci-common.c +++ b/arch/powerpc/kernel/pci-common.c @@ -419,7 +419,7 @@ pgprot_t pci_phys_mem_access_prot(struct file *file, struct pci_dev *pdev = NULL; struct resource *found = NULL; unsigned long prot = pgprot_val(protection); - unsigned long offset = pfn << PAGE_SHIFT; + resource_size_t offset = ((resource_size_t)pfn) << PAGE_SHIFT; int i; if (page_is_ram(pfn)) @@ -470,7 +470,8 @@ pgprot_t pci_phys_mem_access_prot(struct file *file, int pci_mmap_page_range(struct pci_dev *dev, struct vm_area_struct *vma, enum pci_mmap_state mmap_state, int write_combine) { - resource_size_t offset = vma->vm_pgoff << PAGE_SHIFT; + resource_size_t offset = + ((resource_size_t)vma->vm_pgoff) << PAGE_SHIFT; struct resource *rp; int ret; -- cgit v1.2.3 From f43c32efacd82bb1427c3247c636e23ece6b8fc9 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Wed, 8 Oct 2008 11:36:21 -0600 Subject: powerpc/mpc5200: trivial printk-fixes in mpc52xx_common - one printk was missing a loglevel - remove double space while we are here Signed-off-by: Wolfram Sang Signed-off-by: Grant Likely --- arch/powerpc/platforms/52xx/mpc52xx_common.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/52xx/mpc52xx_common.c b/arch/powerpc/platforms/52xx/mpc52xx_common.c index 4d5fd1dbd40..044b4e6e874 100644 --- a/arch/powerpc/platforms/52xx/mpc52xx_common.c +++ b/arch/powerpc/platforms/52xx/mpc52xx_common.c @@ -90,7 +90,7 @@ mpc5200_setup_xlb_arbiter(void) of_node_put(np); if (!xlb) { printk(KERN_ERR __FILE__ ": " - "Error mapping XLB in mpc52xx_setup_cpu(). " + "Error mapping XLB in mpc52xx_setup_cpu(). " "Expect some abnormal behavior\n"); return; } @@ -216,7 +216,8 @@ mpc52xx_restart(char *cmd) out_be32(&mpc52xx_wdt->count, 0x000000ff); out_be32(&mpc52xx_wdt->mode, 0x00009004); } else - printk("mpc52xx_restart: Can't access wdt. " + printk(KERN_ERR __FILE__ ": " + "mpc52xx_restart: Can't access wdt. " "Restart impossible, system halted.\n"); while (1); -- cgit v1.2.3 From e92350463891a20960e858ef6137aa456e616175 Mon Sep 17 00:00:00 2001 From: Tony Breeds Date: Wed, 8 Oct 2008 11:36:57 -0600 Subject: powerpc/mpc5200: Silence warnings in arch/powerpc/platforms/52xx/mpc52xx_pci.c Explicitly cast resource fields to unsigned long long, and match format specifier. Signed-off-by: Tony Breeds Signed-off-by: Grant Likely --- arch/powerpc/platforms/52xx/mpc52xx_pci.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/52xx/mpc52xx_pci.c b/arch/powerpc/platforms/52xx/mpc52xx_pci.c index 5a382bb15f6..b49a1852766 100644 --- a/arch/powerpc/platforms/52xx/mpc52xx_pci.c +++ b/arch/powerpc/platforms/52xx/mpc52xx_pci.c @@ -265,8 +265,11 @@ mpc52xx_pci_setup(struct pci_controller *hose, /* Memory windows */ res = &hose->mem_resources[0]; if (res->flags) { - pr_debug("mem_resource[0] = {.start=%x, .end=%x, .flags=%lx}\n", - res->start, res->end, res->flags); + pr_debug("mem_resource[0] = " + "{.start=%llx, .end=%llx, .flags=%llx}\n", + (unsigned long long)res->start, + (unsigned long long)res->end, + (unsigned long long)res->flags); out_be32(&pci_regs->iw0btar, MPC52xx_PCI_IWBTAR_TRANSLATION(res->start, res->start, res->end - res->start + 1)); @@ -297,9 +300,11 @@ mpc52xx_pci_setup(struct pci_controller *hose, printk(KERN_ERR "%s: Didn't find IO resources\n", __FILE__); return; } - pr_debug(".io_resource={.start=%x,.end=%x,.flags=%lx} " + pr_debug(".io_resource={.start=%llx,.end=%llx,.flags=%llx} " ".io_base_phys=0x%p\n", - res->start, res->end, res->flags, (void*)hose->io_base_phys); + (unsigned long long)res->start, + (unsigned long long)res->end, + (unsigned long long)res->flags, (void*)hose->io_base_phys); out_be32(&pci_regs->iw2btar, MPC52xx_PCI_IWBTAR_TRANSLATION(hose->io_base_phys, res->start, -- cgit v1.2.3 From e2ed6e4daa6f16f088600d98568cb5730b5238a6 Mon Sep 17 00:00:00 2001 From: Jeremy Kerr Date: Tue, 7 Oct 2008 18:26:55 +1100 Subject: powerpc/spufs: set nlink count for spufs root correctly Currently, an empty spufs root inode has nlink count of 1. However, the directory has two links; / -> spu and /spu/ -> . This change increments the link count of the root inode in spufs. Signed-off-by: Jeremy Kerr --- arch/powerpc/platforms/cell/spufs/inode.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/powerpc/platforms/cell/spufs/inode.c b/arch/powerpc/platforms/cell/spufs/inode.c index 690ca7b0dcf..0d262b9f94a 100644 --- a/arch/powerpc/platforms/cell/spufs/inode.c +++ b/arch/powerpc/platforms/cell/spufs/inode.c @@ -755,6 +755,7 @@ spufs_create_root(struct super_block *sb, void *data) inode->i_op = &simple_dir_inode_operations; inode->i_fop = &simple_dir_operations; SPUFS_I(inode)->i_ctx = NULL; + inc_nlink(inode); ret = -EINVAL; if (!spufs_parse_options(sb, data, inode)) -- cgit v1.2.3 From ba0b996d01eaca4f3cc1f07dcc238fcad7e0d427 Mon Sep 17 00:00:00 2001 From: Jeremy Kerr Date: Thu, 9 Oct 2008 10:39:21 +1100 Subject: powerpc/spufs: use inc_nlink Style change: use inc_nlink instead of incrementing i_nlink directly Signed-off-by: Jeremy Kerr --- arch/powerpc/platforms/cell/spufs/inode.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/cell/spufs/inode.c b/arch/powerpc/platforms/cell/spufs/inode.c index 0d262b9f94a..d79ac67c9df 100644 --- a/arch/powerpc/platforms/cell/spufs/inode.c +++ b/arch/powerpc/platforms/cell/spufs/inode.c @@ -298,8 +298,8 @@ spufs_mkdir(struct inode *dir, struct dentry *dentry, unsigned int flags, d_instantiate(dentry, inode); dget(dentry); - dir->i_nlink++; - dentry->d_inode->i_nlink++; + inc_nlink(dir); + inc_nlink(dentry->d_inode); goto out; out_free_ctx: @@ -538,8 +538,8 @@ spufs_mkgang(struct inode *dir, struct dentry *dentry, int mode) inode->i_fop = &simple_dir_operations; d_instantiate(dentry, inode); - dir->i_nlink++; - dentry->d_inode->i_nlink++; + inc_nlink(dir); + inc_nlink(dentry->d_inode); return ret; out_iput: -- cgit v1.2.3 From 6747c2ee8abf749e63fee8cd01a9ee293e6a4247 Mon Sep 17 00:00:00 2001 From: Kou Ishizaki Date: Thu, 9 Oct 2008 10:45:49 +1100 Subject: powerpc/spufs: add a missing mutex_unlock A mutex_unlock(&gang->aff_mutex) in spufs_create_context() is missing in case spufs_context_open() fails. As a result, spu_create syscall and spu_get_idle() may block. This patch adds the mutex_unlock. Signed-off-by: Kou Ishizaki Signed-off-by: Jeremy Kerr Acked-by: Andre Detsch --- arch/powerpc/platforms/cell/spufs/inode.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/platforms/cell/spufs/inode.c b/arch/powerpc/platforms/cell/spufs/inode.c index d79ac67c9df..6b7c7b13245 100644 --- a/arch/powerpc/platforms/cell/spufs/inode.c +++ b/arch/powerpc/platforms/cell/spufs/inode.c @@ -496,6 +496,8 @@ spufs_create_context(struct inode *inode, struct dentry *dentry, ret = spufs_context_open(dget(dentry), mntget(mnt)); if (ret < 0) { WARN_ON(spufs_rmdir(inode, dentry)); + if (affinity) + mutex_unlock(&gang->aff_mutex); mutex_unlock(&inode->i_mutex); spu_forget(SPUFS_I(dentry->d_inode)->i_ctx); goto out; -- cgit v1.2.3 From 9fd3f88cb67ac51bd5face8441472b91e042be67 Mon Sep 17 00:00:00 2001 From: Nathan Fontenot Date: Wed, 1 Oct 2008 09:44:02 +0000 Subject: powerpc: Oops in pseries_lmb_remove() Testing hotplug memory remove has revealed that we can oops in pseries_lmb_remove(). The incorrect shift causes a NULL pointer dereference in the page_zone() inline routine. I have only been able to reproduce the oops on kernels with large pages enabled. Tested on Power5 and Power6 with and without large pages enabled. Signed-off-by: Nathan Fontenot Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/hotplug-memory.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/hotplug-memory.c b/arch/powerpc/platforms/pseries/hotplug-memory.c index a1a368dd2d9..140d02a5232 100644 --- a/arch/powerpc/platforms/pseries/hotplug-memory.c +++ b/arch/powerpc/platforms/pseries/hotplug-memory.c @@ -21,7 +21,7 @@ static int pseries_remove_lmb(unsigned long base, unsigned int lmb_size) struct zone *zone; int ret; - start_pfn = base >> PFN_SECTION_SHIFT; + start_pfn = base >> PAGE_SHIFT; zone = page_zone(pfn_to_page(start_pfn)); /* -- cgit v1.2.3 From 99c840668c23fa81ac642598c792926021329747 Mon Sep 17 00:00:00 2001 From: Roel Kluin <12o3l@tiscali.nl> Date: Mon, 6 Oct 2008 22:38:33 +0000 Subject: powerpc/cell/oprofile: Fix test on overlay_tbl_offset in vma_map Offset is unsigned and when an address isn't found in the vma map vma_map_lookup() returns the vma physical address + 0x10000000. vma_map_lookup used to return 0xffffffff on a failed lookup, but a change was made to return the vma physical address + 0x10000000 There are two callers of vam_map_lookup: one of them correctly deals with this new return value, but the other (below) did not. Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Acked-by: Maynard Johnson Signed-off-by: Arnd Bergmann Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/oprofile/cell/vma_map.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/oprofile/cell/vma_map.c b/arch/powerpc/oprofile/cell/vma_map.c index fff66662d02..258fa4411e9 100644 --- a/arch/powerpc/oprofile/cell/vma_map.c +++ b/arch/powerpc/oprofile/cell/vma_map.c @@ -229,7 +229,7 @@ struct vma_to_fileoffset_map *create_vma_map(const struct spu *aSpu, */ overlay_tbl_offset = vma_map_lookup(map, ovly_table_sym, aSpu, &grd_val); - if (overlay_tbl_offset < 0) { + if (overlay_tbl_offset > 0x10000000) { printk(KERN_ERR "SPU_PROF: " "%s, line %d: Error finding SPU overlay table\n", __func__, __LINE__); -- cgit v1.2.3 From 41c2e949cb7b80c5a6247c7df97759953b0f71b5 Mon Sep 17 00:00:00 2001 From: Josh Poimboeuf Date: Tue, 7 Oct 2008 06:10:03 +0000 Subject: powerpc: Fix error path in kernel_thread function The powerpc 32-bit and 64-bit kernel_thread functions don't properly propagate errors being returned by the clone syscall. (In the case of error, the syscall exit code returns a positive errno in r3 and sets the CR0[SO] bit.) This patch fixes that by negating r3 if CR0[SO] is set after the syscall. Signed-off-by: Josh Poimboeuf Signed-off-by: Josh Boyer Acked-by: Paul Mackerras Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/misc_32.S | 8 +++++--- arch/powerpc/kernel/misc_64.S | 8 +++++--- 2 files changed, 10 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/misc_32.S b/arch/powerpc/kernel/misc_32.S index e9c8ab6eabf..6a9b4bf0d17 100644 --- a/arch/powerpc/kernel/misc_32.S +++ b/arch/powerpc/kernel/misc_32.S @@ -900,8 +900,10 @@ _GLOBAL(kernel_thread) li r4,0 /* new sp (unused) */ li r0,__NR_clone sc - cmpwi 0,r3,0 /* parent or child? */ - bne 1f /* return if parent */ + bns+ 1f /* did system call indicate error? */ + neg r3,r3 /* if so, make return code negative */ +1: cmpwi 0,r3,0 /* parent or child? */ + bne 2f /* return if parent */ li r0,0 /* make top-level stack frame */ stwu r0,-16(r1) mtlr r30 /* fn addr in lr */ @@ -911,7 +913,7 @@ _GLOBAL(kernel_thread) li r0,__NR_exit /* exit if function returns */ li r3,0 sc -1: lwz r30,8(r1) +2: lwz r30,8(r1) lwz r31,12(r1) addi r1,r1,16 blr diff --git a/arch/powerpc/kernel/misc_64.S b/arch/powerpc/kernel/misc_64.S index 4dd70cf7bb4..3053fe5c62f 100644 --- a/arch/powerpc/kernel/misc_64.S +++ b/arch/powerpc/kernel/misc_64.S @@ -426,8 +426,10 @@ _GLOBAL(kernel_thread) li r4,0 /* new sp (unused) */ li r0,__NR_clone sc - cmpdi 0,r3,0 /* parent or child? */ - bne 1f /* return if parent */ + bns+ 1f /* did system call indicate error? */ + neg r3,r3 /* if so, make return code negative */ +1: cmpdi 0,r3,0 /* parent or child? */ + bne 2f /* return if parent */ li r0,0 stdu r0,-STACK_FRAME_OVERHEAD(r1) ld r2,8(r29) @@ -438,7 +440,7 @@ _GLOBAL(kernel_thread) li r0,__NR_exit /* exit after child exits */ li r3,0 sc -1: addi r1,r1,STACK_FRAME_OVERHEAD +2: addi r1,r1,STACK_FRAME_OVERHEAD ld r29,-24(r1) ld r30,-16(r1) blr -- cgit v1.2.3 From 91a00302959545a9ae423e99732b1e46eb19e877 Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Wed, 8 Oct 2008 14:03:29 +0000 Subject: powerpc: Sync RPA note in zImage with kernel's RPA note Commit 9b09c6d909dfd8de96b99b9b9c808b94b0a71614 ("powerpc: Change the default link address for pSeries zImage kernels") changed the real-base value in the CHRP note added by the addnote program from 12MB to 32MB to give more space for Open Firmware to load the zImage. (The real-base value says where we want OF to position itself in memory.) However, this change was ineffective on most pSeries machines, because the RPA note added by addnote has the "ignore me" flag set to 1. This was intended to tell OF to ignore just the RPA note, but has the side effect of also making OF ignore the CHRP note (at least on most pSeries machines). To solve this we have to set the "ignore me" flag to 0 in the RPA note. (We can't just omit the RPA note because that is equivalent to having an RPA note with default values, and the default values are not what we want.) However, then we have to make sure the values in the zImage's RPA note match up with the values that the kernel supplies later in prom_init.c with either the ibm,client-architecture-support call or the process-elf-header call in prom_send_capabilities(). So this sets the "ignore me" flag in the RPA note in addnote to 0, and adjusts the RPA note values in addnote.c and in prom_init.c to be consistent with each other and with the values in ibm_architecture_vec. However, since the wrapper is independent of the kernel, this doesn't ensure that the notes will stay consistent. To ensure that, this adds code to addnote.c so that it can extract the kernel's RPA note from the kernel binary and put that in the zImage. To that end, we put the kernel's fake ELF header (which contains the kernel's RPA note) into its own section, and arrange for wrapper to pull out that section with objcopy and pass it to addnote, which then extracts the RPA note from it and transfers it to the zImage. Signed-off-by: Paul Mackerras Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/boot/addnote.c | 144 ++++++++++++++++++++++++++++---------- arch/powerpc/boot/wrapper | 4 +- arch/powerpc/kernel/prom_init.c | 10 +-- arch/powerpc/kernel/vmlinux.lds.S | 3 + 4 files changed, 119 insertions(+), 42 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/boot/addnote.c b/arch/powerpc/boot/addnote.c index b1e5611b2ab..dcc9ab2ca82 100644 --- a/arch/powerpc/boot/addnote.c +++ b/arch/powerpc/boot/addnote.c @@ -11,7 +11,12 @@ * as published by the Free Software Foundation; either version * 2 of the License, or (at your option) any later version. * - * Usage: addnote zImage + * Usage: addnote zImage [note.elf] + * + * If note.elf is supplied, it is the name of an ELF file that contains + * an RPA note to use instead of the built-in one. Alternatively, the + * note.elf file may be empty, in which case the built-in RPA note is + * used (this is to simplify how this is invoked from the wrapper script). */ #include #include @@ -43,27 +48,29 @@ char rpaname[] = "IBM,RPA-Client-Config"; */ #define N_RPA_DESCR 8 unsigned int rpanote[N_RPA_DESCR] = { - 0, /* lparaffinity */ - 64, /* min_rmo_size */ + 1, /* lparaffinity */ + 128, /* min_rmo_size */ 0, /* min_rmo_percent */ - 40, /* max_pft_size */ + 46, /* max_pft_size */ 1, /* splpar */ -1, /* min_load */ - 0, /* new_mem_def */ - 1, /* ignore_my_client_config */ + 1, /* new_mem_def */ + 0, /* ignore_my_client_config */ }; #define ROUNDUP(len) (((len) + 3) & ~3) unsigned char buf[512]; +unsigned char notebuf[512]; -#define GET_16BE(off) ((buf[off] << 8) + (buf[(off)+1])) -#define GET_32BE(off) ((GET_16BE(off) << 16) + GET_16BE((off)+2)) +#define GET_16BE(b, off) (((b)[off] << 8) + ((b)[(off)+1])) +#define GET_32BE(b, off) ((GET_16BE((b), (off)) << 16) + \ + GET_16BE((b), (off)+2)) -#define PUT_16BE(off, v) (buf[off] = ((v) >> 8) & 0xff, \ - buf[(off) + 1] = (v) & 0xff) -#define PUT_32BE(off, v) (PUT_16BE((off), (v) >> 16), \ - PUT_16BE((off) + 2, (v))) +#define PUT_16BE(b, off, v) ((b)[off] = ((v) >> 8) & 0xff, \ + (b)[(off) + 1] = (v) & 0xff) +#define PUT_32BE(b, off, v) (PUT_16BE((b), (off), (v) >> 16), \ + PUT_16BE((b), (off) + 2, (v))) /* Structure of an ELF file */ #define E_IDENT 0 /* ELF header */ @@ -88,15 +95,71 @@ unsigned char buf[512]; unsigned char elf_magic[4] = { 0x7f, 'E', 'L', 'F' }; +unsigned char *read_rpanote(const char *fname, int *nnp) +{ + int notefd, nr, i; + int ph, ps, np; + int note, notesize; + + notefd = open(fname, O_RDONLY); + if (notefd < 0) { + perror(fname); + exit(1); + } + nr = read(notefd, notebuf, sizeof(notebuf)); + if (nr < 0) { + perror("read note"); + exit(1); + } + if (nr == 0) /* empty file */ + return NULL; + if (nr < E_HSIZE || + memcmp(¬ebuf[E_IDENT+EI_MAGIC], elf_magic, 4) != 0 || + notebuf[E_IDENT+EI_CLASS] != ELFCLASS32 || + notebuf[E_IDENT+EI_DATA] != ELFDATA2MSB) + goto notelf; + close(notefd); + + /* now look for the RPA-note */ + ph = GET_32BE(notebuf, E_PHOFF); + ps = GET_16BE(notebuf, E_PHENTSIZE); + np = GET_16BE(notebuf, E_PHNUM); + if (ph < E_HSIZE || ps < PH_HSIZE || np < 1) + goto notelf; + + for (i = 0; i < np; ++i, ph += ps) { + if (GET_32BE(notebuf, ph + PH_TYPE) != PT_NOTE) + continue; + note = GET_32BE(notebuf, ph + PH_OFFSET); + notesize = GET_32BE(notebuf, ph + PH_FILESZ); + if (notesize < 34 || note + notesize > nr) + continue; + if (GET_32BE(notebuf, note) != strlen(rpaname) + 1 || + GET_32BE(notebuf, note + 8) != 0x12759999 || + strcmp((char *)¬ebuf[note + 12], rpaname) != 0) + continue; + /* looks like an RPA note, return it */ + *nnp = notesize; + return ¬ebuf[note]; + } + /* no RPA note found */ + return NULL; + + notelf: + fprintf(stderr, "%s is not a big-endian 32-bit ELF image\n", fname); + exit(1); +} + int main(int ac, char **av) { int fd, n, i; int ph, ps, np; int nnote, nnote2, ns; + unsigned char *rpap; - if (ac != 2) { - fprintf(stderr, "Usage: %s elf-file\n", av[0]); + if (ac != 2 && ac != 3) { + fprintf(stderr, "Usage: %s elf-file [rpanote.elf]\n", av[0]); exit(1); } fd = open(av[1], O_RDWR); @@ -107,6 +170,7 @@ main(int ac, char **av) nnote = 12 + ROUNDUP(strlen(arch) + 1) + sizeof(descr); nnote2 = 12 + ROUNDUP(strlen(rpaname) + 1) + sizeof(rpanote); + rpap = NULL; n = read(fd, buf, sizeof(buf)); if (n < 0) { @@ -124,16 +188,19 @@ main(int ac, char **av) exit(1); } - ph = GET_32BE(E_PHOFF); - ps = GET_16BE(E_PHENTSIZE); - np = GET_16BE(E_PHNUM); + if (ac == 3) + rpap = read_rpanote(av[2], &nnote2); + + ph = GET_32BE(buf, E_PHOFF); + ps = GET_16BE(buf, E_PHENTSIZE); + np = GET_16BE(buf, E_PHNUM); if (ph < E_HSIZE || ps < PH_HSIZE || np < 1) goto notelf; if (ph + (np + 2) * ps + nnote + nnote2 > n) goto nospace; for (i = 0; i < np; ++i) { - if (GET_32BE(ph + PH_TYPE) == PT_NOTE) { + if (GET_32BE(buf, ph + PH_TYPE) == PT_NOTE) { fprintf(stderr, "%s already has a note entry\n", av[1]); exit(0); @@ -148,37 +215,42 @@ main(int ac, char **av) /* fill in the program header entry */ ns = ph + 2 * ps; - PUT_32BE(ph + PH_TYPE, PT_NOTE); - PUT_32BE(ph + PH_OFFSET, ns); - PUT_32BE(ph + PH_FILESZ, nnote); + PUT_32BE(buf, ph + PH_TYPE, PT_NOTE); + PUT_32BE(buf, ph + PH_OFFSET, ns); + PUT_32BE(buf, ph + PH_FILESZ, nnote); /* fill in the note area we point to */ /* XXX we should probably make this a proper section */ - PUT_32BE(ns, strlen(arch) + 1); - PUT_32BE(ns + 4, N_DESCR * 4); - PUT_32BE(ns + 8, 0x1275); + PUT_32BE(buf, ns, strlen(arch) + 1); + PUT_32BE(buf, ns + 4, N_DESCR * 4); + PUT_32BE(buf, ns + 8, 0x1275); strcpy((char *) &buf[ns + 12], arch); ns += 12 + strlen(arch) + 1; for (i = 0; i < N_DESCR; ++i, ns += 4) - PUT_32BE(ns, descr[i]); + PUT_32BE(buf, ns, descr[i]); /* fill in the second program header entry and the RPA note area */ ph += ps; - PUT_32BE(ph + PH_TYPE, PT_NOTE); - PUT_32BE(ph + PH_OFFSET, ns); - PUT_32BE(ph + PH_FILESZ, nnote2); + PUT_32BE(buf, ph + PH_TYPE, PT_NOTE); + PUT_32BE(buf, ph + PH_OFFSET, ns); + PUT_32BE(buf, ph + PH_FILESZ, nnote2); /* fill in the note area we point to */ - PUT_32BE(ns, strlen(rpaname) + 1); - PUT_32BE(ns + 4, sizeof(rpanote)); - PUT_32BE(ns + 8, 0x12759999); - strcpy((char *) &buf[ns + 12], rpaname); - ns += 12 + ROUNDUP(strlen(rpaname) + 1); - for (i = 0; i < N_RPA_DESCR; ++i, ns += 4) - PUT_32BE(ns, rpanote[i]); + if (rpap) { + /* RPA note supplied in file, just copy the whole thing over */ + memcpy(buf + ns, rpap, nnote2); + } else { + PUT_32BE(buf, ns, strlen(rpaname) + 1); + PUT_32BE(buf, ns + 4, sizeof(rpanote)); + PUT_32BE(buf, ns + 8, 0x12759999); + strcpy((char *) &buf[ns + 12], rpaname); + ns += 12 + ROUNDUP(strlen(rpaname) + 1); + for (i = 0; i < N_RPA_DESCR; ++i, ns += 4) + PUT_32BE(buf, ns, rpanote[i]); + } /* Update the number of program headers */ - PUT_16BE(E_PHNUM, np + 2); + PUT_16BE(buf, E_PHNUM, np + 2); /* write back */ lseek(fd, (long) 0, SEEK_SET); diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper index 965c237c122..ee0dc41d7c5 100755 --- a/arch/powerpc/boot/wrapper +++ b/arch/powerpc/boot/wrapper @@ -307,7 +307,9 @@ fi # post-processing needed for some platforms case "$platform" in pseries|chrp) - $objbin/addnote "$ofile" + ${CROSS}objcopy -O binary -j .fakeelf "$kernel" "$ofile".rpanote + $objbin/addnote "$ofile" "$ofile".rpanote + rm -r "$ofile".rpanote ;; coff) ${CROSS}objcopy -O aixcoff-rs6000 --set-start "$entry" "$ofile" diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c index 7cf274a2b33..2fdbc18ae94 100644 --- a/arch/powerpc/kernel/prom_init.c +++ b/arch/powerpc/kernel/prom_init.c @@ -732,7 +732,7 @@ static struct fake_elf { u32 ignore_me; } rpadesc; } rpanote; -} fake_elf = { +} fake_elf __section(.fakeelf) = { .elfhdr = { .e_ident = { 0x7f, 'E', 'L', 'F', ELFCLASS32, ELFDATA2MSB, EV_CURRENT }, @@ -774,13 +774,13 @@ static struct fake_elf { .type = 0x12759999, .name = "IBM,RPA-Client-Config", .rpadesc = { - .lpar_affinity = 0, - .min_rmo_size = 64, /* in megabytes */ + .lpar_affinity = 1, + .min_rmo_size = 128, /* in megabytes */ .min_rmo_percent = 0, - .max_pft_size = 48, /* 2^48 bytes max PFT size */ + .max_pft_size = 46, /* 2^46 bytes max PFT size */ .splpar = 1, .min_load = ~0U, - .new_mem_def = 0 + .new_mem_def = 1 } } }; diff --git a/arch/powerpc/kernel/vmlinux.lds.S b/arch/powerpc/kernel/vmlinux.lds.S index e6927fb2e65..b39c27ed791 100644 --- a/arch/powerpc/kernel/vmlinux.lds.S +++ b/arch/powerpc/kernel/vmlinux.lds.S @@ -203,6 +203,9 @@ SECTIONS *(.rela*) } + /* Fake ELF header containing RPA note; for addnote */ + .fakeelf : AT(ADDR(.fakeelf) - LOAD_OFFSET) { *(.fakeelf) } + /* freed after init ends here */ . = ALIGN(PAGE_SIZE); __init_end = .; -- cgit v1.2.3 From 8f64e1f2d1e09267ac926e15090fd505c1c0cbcb Mon Sep 17 00:00:00 2001 From: Jon Tollefson Date: Thu, 9 Oct 2008 10:18:40 +0000 Subject: powerpc: Reserve in bootmem lmb reserved regions that cross NUMA nodes If there are multiple reserved memory blocks via lmb_reserve() that are contiguous addresses and on different NUMA nodes we are losing track of which address ranges to reserve in bootmem on which node. I discovered this when I recently got to try 16GB huge pages on a system with more then 2 nodes. When scanning the device tree in early boot we call lmb_reserve() with the addresses of the 16G pages that we find so that the memory doesn't get used for something else. For example the addresses for the pages could be 4000000000, 4400000000, 4800000000, 4C00000000, etc - 8 pages, one on each of eight nodes. In the lmb after all the pages have been reserved it will look something like the following: lmb_dump_all: memory.cnt = 0x2 memory.size = 0x3e80000000 memory.region[0x0].base = 0x0 .size = 0x1e80000000 memory.region[0x1].base = 0x4000000000 .size = 0x2000000000 reserved.cnt = 0x5 reserved.size = 0x3e80000000 reserved.region[0x0].base = 0x0 .size = 0x7b5000 reserved.region[0x1].base = 0x2a00000 .size = 0x78c000 reserved.region[0x2].base = 0x328c000 .size = 0x43000 reserved.region[0x3].base = 0xf4e8000 .size = 0xb18000 reserved.region[0x4].base = 0x4000000000 .size = 0x2000000000 The reserved.region[0x4] contains the 16G pages. In arch/powerpc/mm/num.c: do_init_bootmem() we loop through each of the node numbers looking for the reserved regions that belong to the particular node. It is not able to identify region 0x4 as being a part of each of the 8 nodes. It is assuming that a reserved region is only on a single node. This patch takes out the reserved region loop from inside the loop that goes over each node. It looks up the active region containing the start of the reserved region. If it extends past that active region then it adjusts the size and gets the next active region containing it. Signed-off-by: Jon Tollefson Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/mm/numa.c | 108 ++++++++++++++++++++++++++++++++++++------------- 1 file changed, 80 insertions(+), 28 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/mm/numa.c b/arch/powerpc/mm/numa.c index be05457631d..6cf5c71c431 100644 --- a/arch/powerpc/mm/numa.c +++ b/arch/powerpc/mm/numa.c @@ -89,6 +89,46 @@ static int __cpuinit fake_numa_create_new_node(unsigned long end_pfn, return 0; } +/* + * get_active_region_work_fn - A helper function for get_node_active_region + * Returns datax set to the start_pfn and end_pfn if they contain + * the initial value of datax->start_pfn between them + * @start_pfn: start page(inclusive) of region to check + * @end_pfn: end page(exclusive) of region to check + * @datax: comes in with ->start_pfn set to value to search for and + * goes out with active range if it contains it + * Returns 1 if search value is in range else 0 + */ +static int __init get_active_region_work_fn(unsigned long start_pfn, + unsigned long end_pfn, void *datax) +{ + struct node_active_region *data; + data = (struct node_active_region *)datax; + + if (start_pfn <= data->start_pfn && end_pfn > data->start_pfn) { + data->start_pfn = start_pfn; + data->end_pfn = end_pfn; + return 1; + } + return 0; + +} + +/* + * get_node_active_region - Return active region containing start_pfn + * @start_pfn: The page to return the region for. + * @node_ar: Returned set to the active region containing start_pfn + */ +static void __init get_node_active_region(unsigned long start_pfn, + struct node_active_region *node_ar) +{ + int nid = early_pfn_to_nid(start_pfn); + + node_ar->nid = nid; + node_ar->start_pfn = start_pfn; + work_with_active_regions(nid, get_active_region_work_fn, node_ar); +} + static void __cpuinit map_cpu_to_node(int cpu, int node) { numa_cpu_lookup_table[cpu] = node; @@ -882,38 +922,50 @@ void __init do_init_bootmem(void) start_pfn, end_pfn); free_bootmem_with_active_regions(nid, end_pfn); + } - /* Mark reserved regions on this node */ - for (i = 0; i < lmb.reserved.cnt; i++) { - unsigned long physbase = lmb.reserved.region[i].base; - unsigned long size = lmb.reserved.region[i].size; - unsigned long start_paddr = start_pfn << PAGE_SHIFT; - unsigned long end_paddr = end_pfn << PAGE_SHIFT; - - if (early_pfn_to_nid(physbase >> PAGE_SHIFT) != nid && - early_pfn_to_nid((physbase+size-1) >> PAGE_SHIFT) != nid) - continue; - - if (physbase < end_paddr && - (physbase+size) > start_paddr) { - /* overlaps */ - if (physbase < start_paddr) { - size -= start_paddr - physbase; - physbase = start_paddr; - } - - if (size > end_paddr - physbase) - size = end_paddr - physbase; - - dbg("reserve_bootmem %lx %lx\n", physbase, - size); - reserve_bootmem_node(NODE_DATA(nid), physbase, - size, BOOTMEM_DEFAULT); - } + /* Mark reserved regions */ + for (i = 0; i < lmb.reserved.cnt; i++) { + unsigned long physbase = lmb.reserved.region[i].base; + unsigned long size = lmb.reserved.region[i].size; + unsigned long start_pfn = physbase >> PAGE_SHIFT; + unsigned long end_pfn = ((physbase + size) >> PAGE_SHIFT); + struct node_active_region node_ar; + + get_node_active_region(start_pfn, &node_ar); + while (start_pfn < end_pfn) { + /* + * if reserved region extends past active region + * then trim size to active region + */ + if (end_pfn > node_ar.end_pfn) + size = (node_ar.end_pfn << PAGE_SHIFT) + - (start_pfn << PAGE_SHIFT); + dbg("reserve_bootmem %lx %lx nid=%d\n", physbase, size, + node_ar.nid); + reserve_bootmem_node(NODE_DATA(node_ar.nid), physbase, + size, BOOTMEM_DEFAULT); + /* + * if reserved region is contained in the active region + * then done. + */ + if (end_pfn <= node_ar.end_pfn) + break; + + /* + * reserved region extends past the active region + * get next active region that contains this + * reserved region + */ + start_pfn = node_ar.end_pfn; + physbase = start_pfn << PAGE_SHIFT; + get_node_active_region(start_pfn, &node_ar); } - sparse_memory_present_with_active_regions(nid); } + + for_each_online_node(nid) + sparse_memory_present_with_active_regions(nid); } void __init paging_init(void) -- cgit v1.2.3 From 8767e9badca7cdf0adc2564d7524092d47ababf3 Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:23 +0000 Subject: powerpc/xics: EOI unmapped irqs after disabling them When reciving an irq vector that does not have a linux mapping, the kernel prints a message and calls RTAS to disable the irq source. Previously the kernel did not EOI the interrupt, causing the source to think it is still being processed by software. While this does add an additional layer of protection against interrupt storms had RTAS failed to disable the source, it also prevents the interrupt from working when a driver later enables it. (We could alternatively send an EOI on startup, but that strategy would likely fail on an emulated xics.) All interrupts should be disabled when the kernel starts, but this can be observed if a driver does not shutdown an interrupt in its reboot hook before starting a new kernel with kexec. Michael reports this can be reproduced trivially by banging the keyboard while kexec'ing on a P5 LPAR: even though the hvc_console driver request's the console irq later in boot, the console is non-functional because we're receiving no console interrupts. Reported-By: Michael Ellerman Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 53 +++++++++++++++++++++++++++-------- 1 file changed, 41 insertions(+), 12 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 6b1a005cc0c..1bccd4a56b5 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -332,32 +332,61 @@ static void xics_eoi_lpar(unsigned int virq) lpar_xirr_info_set((0xff << 24) | irq); } -static inline unsigned int xics_remap_irq(unsigned int vec) +static inline unsigned int xics_xirr_vector(unsigned int xirr) { - unsigned int irq; + /* + * The top byte is the old cppr, to be restored on EOI. + * The remaining 24 bits are the vector. + */ + return xirr & 0x00ffffff; +} - vec &= 0x00ffffff; +static void xics_mask_unknown_vec(unsigned int vec) +{ + printk(KERN_ERR "Interrupt %u (real) is invalid, disabling it.\n", vec); + xics_mask_real_irq(vec); +} + +static unsigned int xics_get_irq_direct(void) +{ + unsigned int xirr = direct_xirr_info_get(); + unsigned int vec = xics_xirr_vector(xirr); + unsigned int irq; if (vec == XICS_IRQ_SPURIOUS) return NO_IRQ; + irq = irq_radix_revmap_lookup(xics_host, vec); if (likely(irq != NO_IRQ)) return irq; - printk(KERN_ERR "Interrupt %u (real) is invalid," - " disabling it.\n", vec); - xics_mask_real_irq(vec); - return NO_IRQ; -} + /* We don't have a linux mapping, so have rtas mask it. */ + xics_mask_unknown_vec(vec); -static unsigned int xics_get_irq_direct(void) -{ - return xics_remap_irq(direct_xirr_info_get()); + /* We might learn about it later, so EOI it */ + direct_xirr_info_set(xirr); + return NO_IRQ; } static unsigned int xics_get_irq_lpar(void) { - return xics_remap_irq(lpar_xirr_info_get()); + unsigned int xirr = lpar_xirr_info_get(); + unsigned int vec = xics_xirr_vector(xirr); + unsigned int irq; + + if (vec == XICS_IRQ_SPURIOUS) + return NO_IRQ; + + irq = irq_radix_revmap_lookup(xics_host, vec); + if (likely(irq != NO_IRQ)) + return irq; + + /* We don't have a linux mapping, so have RTAS mask it. */ + xics_mask_unknown_vec(vec); + + /* We might learn about it later, so EOI it */ + lpar_xirr_info_set(xirr); + return NO_IRQ; } #ifdef CONFIG_SMP -- cgit v1.2.3 From 302905a3473d9a1f00e4b2fe373d2763a041a93d Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:28 +0000 Subject: powerpc/xics: Update default_server during migrate_irqs_away Currently, every time we determine which irq server to use, we check if default_server, which is the id of the bootcpu, is still online. But default_server is a hardware cpu, not the logical cpu id needed to index cpu_online_map. Since the default server can only go offline during a cpu hotplug event, explicitly check the default server and choose the new one when we move irqs away from the cpu being offlined. This has the added benefit of only needing the boot_cpuid to be updated and not relying on the cpu being marked offline during migrate_irqs_away. Also, since xics_update_irq_servers only reads device tree information, we can call it before xics_init_host in xics_init_IRQ and then default_server will always be valid when we can reach get_irq_server via the host ops. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 1bccd4a56b5..c95697912fe 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -208,9 +208,6 @@ static int get_irq_server(unsigned int virq, unsigned int strict_check) cpumask_t cpumask = irq_desc[virq].affinity; cpumask_t tmp = CPU_MASK_NONE; - if (! cpu_isset(default_server, cpu_online_map)) - xics_update_irq_servers(); - if (!distribute_irqs) return default_server; @@ -685,8 +682,8 @@ void __init xics_init_IRQ(void) if (found == 0) return; - xics_init_host(); xics_update_irq_servers(); + xics_init_host(); if (firmware_has_feature(FW_FEATURE_LPAR)) ppc_md.get_irq = xics_get_irq_lpar; @@ -779,6 +776,10 @@ void xics_migrate_irqs_away(void) int cpu = smp_processor_id(), hw_cpu = hard_smp_processor_id(); unsigned int irq, virq; + /* If we used to be the default server, move to the new "boot_cpuid" */ + if (hw_cpu == default_server) + xics_update_irq_servers(); + /* Reject any interrupt that was queued to us... */ xics_set_cpu_priority(0); -- cgit v1.2.3 From 6070bf6afe4c4232ec1e04fa16c056758b2e681b Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Fri, 10 Oct 2008 08:53:21 +0000 Subject: powerpc: Remove old Makefile workaround for arch/ppc There is an old workaround in the sysdev/Makefile for dealing with arch/ppc vs. arch/powerpc compiles. This is no longer needed as arch/ppc is dead. Signed-off-by: Josh Boyer Acked-by: Kumar Gala Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/sysdev/Makefile | 3 --- 1 file changed, 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile index 55618ba9eff..a44709a94f9 100644 --- a/arch/powerpc/sysdev/Makefile +++ b/arch/powerpc/sysdev/Makefile @@ -38,15 +38,12 @@ ifeq ($(CONFIG_PCI),y) obj-$(CONFIG_4xx) += ppc4xx_pci.o endif -# Temporary hack until we have migrated to asm-powerpc -ifeq ($(ARCH),powerpc) obj-$(CONFIG_CPM) += cpm_common.o obj-$(CONFIG_CPM2) += cpm2.o cpm2_pic.o obj-$(CONFIG_QUICC_ENGINE) += cpm_common.o obj-$(CONFIG_PPC_DCR) += dcr.o obj-$(CONFIG_8xx) += mpc8xx_pic.o cpm1.o obj-$(CONFIG_UCODE_PATCH) += micropatch.o -endif ifeq ($(CONFIG_SUSPEND),y) obj-$(CONFIG_6xx) += 6xx-suspend.o -- cgit v1.2.3 From 78b5b626fa9048337530cc3ba4ceb9e4ee96a386 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Fri, 10 Oct 2008 09:44:33 +0000 Subject: powerpc: Make ppc32 respect the boot cpu id for !CONFIG_SMP Previously the FDT header field boot_cpuid_phys wasn't actually used on ppc32. Instead the physical boot cpuid was assumed to be 0 for !CONFIG_SMP. Signed-off-by: Kumar Gala Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/smp.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/smp.h b/arch/powerpc/include/asm/smp.h index c092f84302f..1866cec4f96 100644 --- a/arch/powerpc/include/asm/smp.h +++ b/arch/powerpc/include/asm/smp.h @@ -93,7 +93,7 @@ extern void __cpu_die(unsigned int cpu); #else /* for UP */ -#define hard_smp_processor_id() 0 +#define hard_smp_processor_id() get_hard_smp_processor_id(0) #define smp_setup_cpu_maps() #endif /* CONFIG_SMP */ @@ -122,6 +122,7 @@ static inline int get_hard_smp_processor_id(int cpu) static inline void set_hard_smp_processor_id(int cpu, int phys) { + boot_cpuid_phys = phys; } #endif /* !CONFIG_SMP */ #endif /* !CONFIG_PPC64 */ -- cgit v1.2.3 From d13f7208b211dd3613bdb04e2647081a5160d68f Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:29 +0000 Subject: powerpc/xics: Consolidate ipi message encode and decode xics supports only one ipi per cpu, and expects software to use some queue to know why the interrupt was sent. In Linux, we use a an array of bitmaps indexed by cpu to identify the message. Currently the bits are set in smp.c and decoded in xics.c, with the data structure in a header file. Consolidate the code in xics.c similar to mpic and other interrupt controllers. Also, while making the the array static, the message word doesn't need to be volatile as set_bit and test_clear_bit take care of it for us, and put it under ifdef smp. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/smp.c | 32 +----------------- arch/powerpc/platforms/pseries/xics.c | 61 ++++++++++++++++++++++++++--------- arch/powerpc/platforms/pseries/xics.h | 12 ++----- 3 files changed, 48 insertions(+), 57 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/smp.c b/arch/powerpc/platforms/pseries/smp.c index 9d8f8c84ab8..e00f96baa38 100644 --- a/arch/powerpc/platforms/pseries/smp.c +++ b/arch/powerpc/platforms/pseries/smp.c @@ -37,7 +37,6 @@ #include #include #include -#include "xics.h" #include #include #include @@ -49,6 +48,7 @@ #include "plpar_wrappers.h" #include "pseries.h" +#include "xics.h" /* @@ -105,36 +105,6 @@ static inline int __devinit smp_startup_cpu(unsigned int lcpu) } #ifdef CONFIG_XICS -static inline void smp_xics_do_message(int cpu, int msg) -{ - set_bit(msg, &xics_ipi_message[cpu].value); - mb(); - xics_cause_IPI(cpu); -} - -static void smp_xics_message_pass(int target, int msg) -{ - unsigned int i; - - if (target < NR_CPUS) { - smp_xics_do_message(target, msg); - } else { - for_each_online_cpu(i) { - if (target == MSG_ALL_BUT_SELF - && i == smp_processor_id()) - continue; - smp_xics_do_message(i, msg); - } - } -} - -static int __init smp_xics_probe(void) -{ - xics_request_IPIs(); - - return cpus_weight(cpu_possible_map); -} - static void __devinit smp_xics_setup_cpu(int cpu) { if (cpu != boot_cpuid) diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index c95697912fe..c0cb356833f 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -71,11 +71,6 @@ static unsigned int interrupt_server_size = 8; static struct irq_host *xics_host; -/* - * XICS only has a single IPI, so encode the messages per CPU - */ -struct xics_ipi_struct xics_ipi_message[NR_CPUS] __cacheline_aligned; - /* RTAS service tokens */ static int ibm_get_xive; static int ibm_set_xive; @@ -201,6 +196,15 @@ static void xics_update_irq_servers(void) } #ifdef CONFIG_SMP +/* + * XICS only has a single IPI, so encode the messages per CPU + */ +struct xics_ipi_struct { + unsigned long value; + } ____cacheline_aligned; + +static struct xics_ipi_struct xics_ipi_message[NR_CPUS] __cacheline_aligned; + static int get_irq_server(unsigned int virq, unsigned int strict_check) { int server; @@ -387,7 +391,6 @@ static unsigned int xics_get_irq_lpar(void) } #ifdef CONFIG_SMP - static irqreturn_t xics_ipi_dispatch(int cpu) { WARN_ON(cpu_is_offline(cpu)); @@ -419,6 +422,33 @@ static irqreturn_t xics_ipi_dispatch(int cpu) return IRQ_HANDLED; } +static inline void smp_xics_do_message(int cpu, int msg) +{ + set_bit(msg, &xics_ipi_message[cpu].value); + mb(); + if (firmware_has_feature(FW_FEATURE_LPAR)) + lpar_qirr_info(cpu, IPI_PRIORITY); + else + direct_qirr_info(cpu, IPI_PRIORITY); +} + +void smp_xics_message_pass(int target, int msg) +{ + unsigned int i; + + if (target < NR_CPUS) { + smp_xics_do_message(target, msg); + } else { + for_each_online_cpu(i) { + if (target == MSG_ALL_BUT_SELF + && i == smp_processor_id()) + continue; + smp_xics_do_message(i, msg); + } + } +} + + static irqreturn_t xics_ipi_action_direct(int irq, void *dev_id) { int cpu = smp_processor_id(); @@ -436,15 +466,6 @@ static irqreturn_t xics_ipi_action_lpar(int irq, void *dev_id) return xics_ipi_dispatch(cpu); } - -void xics_cause_IPI(int cpu) -{ - if (firmware_has_feature(FW_FEATURE_LPAR)) - lpar_qirr_info(cpu, IPI_PRIORITY); - else - direct_qirr_info(cpu, IPI_PRIORITY); -} - #endif /* CONFIG_SMP */ static void xics_set_cpu_priority(unsigned char cppr) @@ -697,7 +718,7 @@ void __init xics_init_IRQ(void) #ifdef CONFIG_SMP -void xics_request_IPIs(void) +static void xics_request_ipi(void) { unsigned int ipi; int rc; @@ -718,6 +739,14 @@ void xics_request_IPIs(void) "IPI", NULL); BUG_ON(rc); } + +int __init smp_xics_probe(void) +{ + xics_request_ipi(); + + return cpus_weight(cpu_possible_map); +} + #endif /* CONFIG_SMP */ void xics_teardown_cpu(void) diff --git a/arch/powerpc/platforms/pseries/xics.h b/arch/powerpc/platforms/pseries/xics.h index 1c5321ae8f2..d1d5a83039a 100644 --- a/arch/powerpc/platforms/pseries/xics.h +++ b/arch/powerpc/platforms/pseries/xics.h @@ -12,20 +12,12 @@ #ifndef _POWERPC_KERNEL_XICS_H #define _POWERPC_KERNEL_XICS_H -#include - extern void xics_init_IRQ(void); extern void xics_setup_cpu(void); extern void xics_teardown_cpu(void); extern void xics_kexec_teardown_cpu(int secondary); -extern void xics_cause_IPI(int cpu); -extern void xics_request_IPIs(void); extern void xics_migrate_irqs_away(void); - -struct xics_ipi_struct { - volatile unsigned long value; -} ____cacheline_aligned; - -extern struct xics_ipi_struct xics_ipi_message[NR_CPUS] __cacheline_aligned; +extern int smp_xics_probe(void); +extern void smp_xics_message_pass(int target, int msg); #endif /* _POWERPC_KERNEL_XICS_H */ -- cgit v1.2.3 From 0641cc91b08937578263589feb15182b9ad2b0fc Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:30 +0000 Subject: powerpc/xics: Rearrange file to group code by function Now that xics_update_irq_servers is called only from init and hotplug code, it becomes possible to clean up the ordering of functions in the file, grouping them but the interfaces they implement. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 432 +++++++++++++++++----------------- 1 file changed, 217 insertions(+), 215 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index c0cb356833f..c98e3a12846 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -9,7 +9,6 @@ * 2 of the License, or (at your option) any later version. */ - #include #include #include @@ -35,6 +34,8 @@ #include "xics.h" #include "plpar_wrappers.h" +static struct irq_host *xics_host; + #define XICS_IPI 2 #define XICS_IRQ_SPURIOUS 0 @@ -47,6 +48,20 @@ */ #define IPI_PRIORITY 4 +static unsigned int default_server = 0xFF; +static unsigned int default_distrib_server = 0; +static unsigned int interrupt_server_size = 8; + +/* RTAS service tokens */ +static int ibm_get_xive; +static int ibm_set_xive; +static int ibm_int_on; +static int ibm_int_off; + + +/* Direct hardware low level accessors */ + +/* The part of the interrupt presentation layer that we care about */ struct xics_ipl { union { u32 word; @@ -65,22 +80,6 @@ struct xics_ipl { static struct xics_ipl __iomem *xics_per_cpu[NR_CPUS]; -static unsigned int default_server = 0xFF; -static unsigned int default_distrib_server = 0; -static unsigned int interrupt_server_size = 8; - -static struct irq_host *xics_host; - -/* RTAS service tokens */ -static int ibm_get_xive; -static int ibm_set_xive; -static int ibm_int_on; -static int ibm_int_off; - - -/* Direct HW low level accessors */ - - static inline unsigned int direct_xirr_info_get(void) { int cpu = smp_processor_id(); @@ -110,7 +109,6 @@ static inline void direct_qirr_info(int n_cpu, u8 value) /* LPAR low level accessors */ - static inline unsigned int lpar_xirr_info_get(void) { unsigned long lpar_rc; @@ -152,59 +150,9 @@ static inline void lpar_qirr_info(int n_cpu , u8 value) } -/* High level handlers and init code */ - -static void xics_update_irq_servers(void) -{ - int i, j; - struct device_node *np; - u32 ilen; - const u32 *ireg, *isize; - u32 hcpuid; - - /* Find the server numbers for the boot cpu. */ - np = of_get_cpu_node(boot_cpuid, NULL); - BUG_ON(!np); - - ireg = of_get_property(np, "ibm,ppc-interrupt-gserver#s", &ilen); - if (!ireg) { - of_node_put(np); - return; - } - - i = ilen / sizeof(int); - hcpuid = get_hard_smp_processor_id(boot_cpuid); - - /* Global interrupt distribution server is specified in the last - * entry of "ibm,ppc-interrupt-gserver#s" property. Get the last - * entry fom this property for current boot cpu id and use it as - * default distribution server - */ - for (j = 0; j < i; j += 2) { - if (ireg[j] == hcpuid) { - default_server = hcpuid; - default_distrib_server = ireg[j+1]; - - isize = of_get_property(np, - "ibm,interrupt-server#-size", NULL); - if (isize) - interrupt_server_size = *isize; - } - } - - of_node_put(np); -} +/* Interface to generic irq subsystem */ #ifdef CONFIG_SMP -/* - * XICS only has a single IPI, so encode the messages per CPU - */ -struct xics_ipi_struct { - unsigned long value; - } ____cacheline_aligned; - -static struct xics_ipi_struct xics_ipi_message[NR_CPUS] __cacheline_aligned; - static int get_irq_server(unsigned int virq, unsigned int strict_check) { int server; @@ -239,7 +187,6 @@ static int get_irq_server(unsigned int virq, unsigned int strict_check) } #endif - static void xics_unmask_irq(unsigned int virq) { unsigned int irq; @@ -273,6 +220,13 @@ static void xics_unmask_irq(unsigned int virq) } } +static unsigned int xics_startup(unsigned int virq) +{ + /* unmask it */ + xics_unmask_irq(virq); + return 0; +} + static void xics_mask_real_irq(unsigned int irq) { int call_status; @@ -309,28 +263,10 @@ static void xics_mask_irq(unsigned int virq) xics_mask_real_irq(irq); } -static unsigned int xics_startup(unsigned int virq) -{ - /* unmask it */ - xics_unmask_irq(virq); - return 0; -} - -static void xics_eoi_direct(unsigned int virq) -{ - unsigned int irq = (unsigned int)irq_map[virq].hwirq; - - iosync(); - direct_xirr_info_set((0xff << 24) | irq); -} - - -static void xics_eoi_lpar(unsigned int virq) +static void xics_mask_unknown_vec(unsigned int vec) { - unsigned int irq = (unsigned int)irq_map[virq].hwirq; - - iosync(); - lpar_xirr_info_set((0xff << 24) | irq); + printk(KERN_ERR "Interrupt %u (real) is invalid, disabling it.\n", vec); + xics_mask_real_irq(vec); } static inline unsigned int xics_xirr_vector(unsigned int xirr) @@ -342,12 +278,6 @@ static inline unsigned int xics_xirr_vector(unsigned int xirr) return xirr & 0x00ffffff; } -static void xics_mask_unknown_vec(unsigned int vec) -{ - printk(KERN_ERR "Interrupt %u (real) is invalid, disabling it.\n", vec); - xics_mask_real_irq(vec); -} - static unsigned int xics_get_irq_direct(void) { unsigned int xirr = direct_xirr_info_get(); @@ -390,91 +320,20 @@ static unsigned int xics_get_irq_lpar(void) return NO_IRQ; } -#ifdef CONFIG_SMP -static irqreturn_t xics_ipi_dispatch(int cpu) -{ - WARN_ON(cpu_is_offline(cpu)); - - while (xics_ipi_message[cpu].value) { - if (test_and_clear_bit(PPC_MSG_CALL_FUNCTION, - &xics_ipi_message[cpu].value)) { - mb(); - smp_message_recv(PPC_MSG_CALL_FUNCTION); - } - if (test_and_clear_bit(PPC_MSG_RESCHEDULE, - &xics_ipi_message[cpu].value)) { - mb(); - smp_message_recv(PPC_MSG_RESCHEDULE); - } - if (test_and_clear_bit(PPC_MSG_CALL_FUNC_SINGLE, - &xics_ipi_message[cpu].value)) { - mb(); - smp_message_recv(PPC_MSG_CALL_FUNC_SINGLE); - } -#if defined(CONFIG_DEBUGGER) || defined(CONFIG_KEXEC) - if (test_and_clear_bit(PPC_MSG_DEBUGGER_BREAK, - &xics_ipi_message[cpu].value)) { - mb(); - smp_message_recv(PPC_MSG_DEBUGGER_BREAK); - } -#endif - } - return IRQ_HANDLED; -} - -static inline void smp_xics_do_message(int cpu, int msg) -{ - set_bit(msg, &xics_ipi_message[cpu].value); - mb(); - if (firmware_has_feature(FW_FEATURE_LPAR)) - lpar_qirr_info(cpu, IPI_PRIORITY); - else - direct_qirr_info(cpu, IPI_PRIORITY); -} - -void smp_xics_message_pass(int target, int msg) -{ - unsigned int i; - - if (target < NR_CPUS) { - smp_xics_do_message(target, msg); - } else { - for_each_online_cpu(i) { - if (target == MSG_ALL_BUT_SELF - && i == smp_processor_id()) - continue; - smp_xics_do_message(i, msg); - } - } -} - - -static irqreturn_t xics_ipi_action_direct(int irq, void *dev_id) +static void xics_eoi_direct(unsigned int virq) { - int cpu = smp_processor_id(); - - direct_qirr_info(cpu, 0xff); + unsigned int irq = (unsigned int)irq_map[virq].hwirq; - return xics_ipi_dispatch(cpu); + iosync(); + direct_xirr_info_set((0xff << 24) | irq); } -static irqreturn_t xics_ipi_action_lpar(int irq, void *dev_id) +static void xics_eoi_lpar(unsigned int virq) { - int cpu = smp_processor_id(); - - lpar_qirr_info(cpu, 0xff); - - return xics_ipi_dispatch(cpu); -} -#endif /* CONFIG_SMP */ + unsigned int irq = (unsigned int)irq_map[virq].hwirq; -static void xics_set_cpu_priority(unsigned char cppr) -{ - if (firmware_has_feature(FW_FEATURE_LPAR)) - lpar_cppr_info(cppr); - else - direct_cppr_info(cppr); iosync(); + lpar_xirr_info_set((0xff << 24) | irq); } static void xics_set_affinity(unsigned int virq, cpumask_t cpumask) @@ -519,22 +378,6 @@ static void xics_set_affinity(unsigned int virq, cpumask_t cpumask) } } -void xics_setup_cpu(void) -{ - xics_set_cpu_priority(0xff); - - /* - * Put the calling processor into the GIQ. This is really only - * necessary from a secondary thread as the OF start-cpu interface - * performs this function for us on primary threads. - * - * XXX: undo of teardown on kexec needs this too, as may hotplug - */ - rtas_set_indicator_fast(GLOBAL_INTERRUPT_QUEUE, - (1UL << interrupt_server_size) - 1 - default_distrib_server, 1); -} - - static struct irq_chip xics_pic_direct = { .typename = " XICS ", .startup = xics_startup, @@ -544,7 +387,6 @@ static struct irq_chip xics_pic_direct = { .set_affinity = xics_set_affinity }; - static struct irq_chip xics_pic_lpar = { .typename = " XICS ", .startup = xics_startup, @@ -554,6 +396,9 @@ static struct irq_chip xics_pic_lpar = { .set_affinity = xics_set_affinity }; + +/* Interface to arch irq controller subsystem layer */ + /* Points to the irq_chip we're actually using */ static struct irq_chip *xics_irq_chip; @@ -613,6 +458,169 @@ static void __init xics_init_host(void) irq_set_default_host(xics_host); } + +/* Inter-processor interrupt support */ + +#ifdef CONFIG_SMP +/* + * XICS only has a single IPI, so encode the messages per CPU + */ +struct xics_ipi_struct { + unsigned long value; + } ____cacheline_aligned; + +static struct xics_ipi_struct xics_ipi_message[NR_CPUS] __cacheline_aligned; + +static inline void smp_xics_do_message(int cpu, int msg) +{ + set_bit(msg, &xics_ipi_message[cpu].value); + mb(); + if (firmware_has_feature(FW_FEATURE_LPAR)) + lpar_qirr_info(cpu, IPI_PRIORITY); + else + direct_qirr_info(cpu, IPI_PRIORITY); +} + +void smp_xics_message_pass(int target, int msg) +{ + unsigned int i; + + if (target < NR_CPUS) { + smp_xics_do_message(target, msg); + } else { + for_each_online_cpu(i) { + if (target == MSG_ALL_BUT_SELF + && i == smp_processor_id()) + continue; + smp_xics_do_message(i, msg); + } + } +} + +static irqreturn_t xics_ipi_dispatch(int cpu) +{ + WARN_ON(cpu_is_offline(cpu)); + + while (xics_ipi_message[cpu].value) { + if (test_and_clear_bit(PPC_MSG_CALL_FUNCTION, + &xics_ipi_message[cpu].value)) { + mb(); + smp_message_recv(PPC_MSG_CALL_FUNCTION); + } + if (test_and_clear_bit(PPC_MSG_RESCHEDULE, + &xics_ipi_message[cpu].value)) { + mb(); + smp_message_recv(PPC_MSG_RESCHEDULE); + } + if (test_and_clear_bit(PPC_MSG_CALL_FUNC_SINGLE, + &xics_ipi_message[cpu].value)) { + mb(); + smp_message_recv(PPC_MSG_CALL_FUNC_SINGLE); + } +#if defined(CONFIG_DEBUGGER) || defined(CONFIG_KEXEC) + if (test_and_clear_bit(PPC_MSG_DEBUGGER_BREAK, + &xics_ipi_message[cpu].value)) { + mb(); + smp_message_recv(PPC_MSG_DEBUGGER_BREAK); + } +#endif + } + return IRQ_HANDLED; +} + +static irqreturn_t xics_ipi_action_direct(int irq, void *dev_id) +{ + int cpu = smp_processor_id(); + + direct_qirr_info(cpu, 0xff); + + return xics_ipi_dispatch(cpu); +} + +static irqreturn_t xics_ipi_action_lpar(int irq, void *dev_id) +{ + int cpu = smp_processor_id(); + + lpar_qirr_info(cpu, 0xff); + + return xics_ipi_dispatch(cpu); +} + +static void xics_request_ipi(void) +{ + unsigned int ipi; + int rc; + + ipi = irq_create_mapping(xics_host, XICS_IPI); + BUG_ON(ipi == NO_IRQ); + + /* + * IPIs are marked IRQF_DISABLED as they must run with irqs + * disabled + */ + set_irq_handler(ipi, handle_percpu_irq); + if (firmware_has_feature(FW_FEATURE_LPAR)) + rc = request_irq(ipi, xics_ipi_action_lpar, IRQF_DISABLED, + "IPI", NULL); + else + rc = request_irq(ipi, xics_ipi_action_direct, IRQF_DISABLED, + "IPI", NULL); + BUG_ON(rc); +} + +int __init smp_xics_probe(void) +{ + xics_request_ipi(); + + return cpus_weight(cpu_possible_map); +} + +#endif /* CONFIG_SMP */ + + +/* Initialization */ + +static void xics_update_irq_servers(void) +{ + int i, j; + struct device_node *np; + u32 ilen; + const u32 *ireg, *isize; + u32 hcpuid; + + /* Find the server numbers for the boot cpu. */ + np = of_get_cpu_node(boot_cpuid, NULL); + BUG_ON(!np); + + ireg = of_get_property(np, "ibm,ppc-interrupt-gserver#s", &ilen); + if (!ireg) { + of_node_put(np); + return; + } + + i = ilen / sizeof(int); + hcpuid = get_hard_smp_processor_id(boot_cpuid); + + /* Global interrupt distribution server is specified in the last + * entry of "ibm,ppc-interrupt-gserver#s" property. Get the last + * entry fom this property for current boot cpu id and use it as + * default distribution server + */ + for (j = 0; j < i; j += 2) { + if (ireg[j] == hcpuid) { + default_server = hcpuid; + default_distrib_server = ireg[j+1]; + + isize = of_get_property(np, + "ibm,interrupt-server#-size", NULL); + if (isize) + interrupt_server_size = *isize; + } + } + + of_node_put(np); +} + static void __init xics_map_one_cpu(int hw_id, unsigned long addr, unsigned long size) { @@ -716,39 +724,33 @@ void __init xics_init_IRQ(void) ppc64_boot_msg(0x21, "XICS Done"); } +/* Cpu startup, shutdown, and hotplug */ -#ifdef CONFIG_SMP -static void xics_request_ipi(void) +static void xics_set_cpu_priority(unsigned char cppr) { - unsigned int ipi; - int rc; - - ipi = irq_create_mapping(xics_host, XICS_IPI); - BUG_ON(ipi == NO_IRQ); - - /* - * IPIs are marked IRQF_DISABLED as they must run with irqs - * disabled - */ - set_irq_handler(ipi, handle_percpu_irq); if (firmware_has_feature(FW_FEATURE_LPAR)) - rc = request_irq(ipi, xics_ipi_action_lpar, IRQF_DISABLED, - "IPI", NULL); + lpar_cppr_info(cppr); else - rc = request_irq(ipi, xics_ipi_action_direct, IRQF_DISABLED, - "IPI", NULL); - BUG_ON(rc); + direct_cppr_info(cppr); + iosync(); } -int __init smp_xics_probe(void) + +void xics_setup_cpu(void) { - xics_request_ipi(); + xics_set_cpu_priority(0xff); - return cpus_weight(cpu_possible_map); + /* + * Put the calling processor into the GIQ. This is really only + * necessary from a secondary thread as the OF start-cpu interface + * performs this function for us on primary threads. + * + * XXX: undo of teardown on kexec needs this too, as may hotplug + */ + rtas_set_indicator_fast(GLOBAL_INTERRUPT_QUEUE, + (1UL << interrupt_server_size) - 1 - default_distrib_server, 1); } -#endif /* CONFIG_SMP */ - void xics_teardown_cpu(void) { int cpu = smp_processor_id(); -- cgit v1.2.3 From 9dc2d44113d1521d8ead8e89e0772c0957b093c2 Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:32 +0000 Subject: powerpc/xics: Change *_xirr_info_set() prototype to avoid casts The xirr is 32 bits in hardware, but the hypervisor requries the upper bits of the register to be clear on the hcall. By changing the type from signed to unsigned int we can drop masking it back to 32 bits. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 11 +++++------ 1 file changed, 5 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index c98e3a12846..98e73720433 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -87,7 +87,7 @@ static inline unsigned int direct_xirr_info_get(void) return in_be32(&xics_per_cpu[cpu]->xirr.word); } -static inline void direct_xirr_info_set(int value) +static inline void direct_xirr_info_set(unsigned int value) { int cpu = smp_processor_id(); @@ -120,15 +120,14 @@ static inline unsigned int lpar_xirr_info_get(void) return (unsigned int)return_value; } -static inline void lpar_xirr_info_set(int value) +static inline void lpar_xirr_info_set(unsigned int value) { unsigned long lpar_rc; - unsigned long val64 = value & 0xffffffff; - lpar_rc = plpar_eoi(val64); + lpar_rc = plpar_eoi(value); if (lpar_rc != H_SUCCESS) - panic("bad return code EOI - rc = %ld, value=%lx\n", lpar_rc, - val64); + panic("bad return code EOI - rc = %ld, value=%x\n", lpar_rc, + value); } static inline void lpar_cppr_info(u8 value) -- cgit v1.2.3 From 188bdddd243e6872608099bd1142a03b70571132 Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:33 +0000 Subject: powerpc/xics: Trim #include list Trim unneeded includes from xics.c. We don't use signals or gfp flags, we use only OF functions and don't need prom, and the 8259 is now handled by our caller. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 98e73720433..3501fa1fe8c 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -15,21 +15,18 @@ #include #include #include -#include #include -#include #include #include +#include #include -#include #include #include #include #include #include #include -#include #include "xics.h" #include "plpar_wrappers.h" -- cgit v1.2.3 From a244a957ab15ddbeccf4018ef4b3ac8f5fd1566d Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:33 +0000 Subject: powerpc/xics: Initialization code cleanups We only need to check the ibm,interrupt-server#-size property once, not once per global server and thread. We can use !CONFIG_SMP cpu masks and hard_smp_processor_id() to avoid an ifdef. Put the node when breaking out of the loop on lpar systems. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 20 ++++++++------------ 1 file changed, 8 insertions(+), 12 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 3501fa1fe8c..27327fc8605 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -606,21 +606,20 @@ static void xics_update_irq_servers(void) if (ireg[j] == hcpuid) { default_server = hcpuid; default_distrib_server = ireg[j+1]; - - isize = of_get_property(np, - "ibm,interrupt-server#-size", NULL); - if (isize) - interrupt_server_size = *isize; } } + /* get the bit size of server numbers */ + isize = of_get_property(np, "ibm,interrupt-server#-size", NULL); + if (isize) + interrupt_server_size = *isize; + of_node_put(np); } static void __init xics_map_one_cpu(int hw_id, unsigned long addr, unsigned long size) { -#ifdef CONFIG_SMP int i; /* This may look gross but it's good enough for now, we don't quite @@ -634,11 +633,6 @@ static void __init xics_map_one_cpu(int hw_id, unsigned long addr, return; } } -#else - if (hw_id != 0) - return; - xics_per_cpu[0] = ioremap(addr, size); -#endif /* CONFIG_SMP */ } static void __init xics_init_one_node(struct device_node *np, @@ -700,8 +694,10 @@ void __init xics_init_IRQ(void) for_each_node_by_type(np, "PowerPC-External-Interrupt-Presentation") { found = 1; - if (firmware_has_feature(FW_FEATURE_LPAR)) + if (firmware_has_feature(FW_FEATURE_LPAR)) { + of_node_put(np); break; + } xics_init_one_node(np, &indx); } if (found == 0) -- cgit v1.2.3 From b4963255ad5a426f04a0bb15c4315fa4bb40cde9 Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:34 +0000 Subject: powerpc/xics: Factor out cpu joining/unjoining the GIQ This factors out processors joining and unjoining the Global Interrupt Queue into a separate function. There is a bit of math to calculate the arguments to rtas to join or leave the global interrupt queue, and a warning on failure afterwards. Make a helper for the 3 callers. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 33 +++++++++++++-------------------- 1 file changed, 13 insertions(+), 20 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 27327fc8605..0bb553331f4 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -727,20 +727,19 @@ static void xics_set_cpu_priority(unsigned char cppr) iosync(); } +/* Have the calling processor join or leave the specified global queue */ +static void xics_set_cpu_giq(unsigned int gserver, unsigned int join) +{ + int status = rtas_set_indicator_fast(GLOBAL_INTERRUPT_QUEUE, + (1UL << interrupt_server_size) - 1 - gserver, join); + WARN_ON(status < 0); +} void xics_setup_cpu(void) { xics_set_cpu_priority(0xff); - /* - * Put the calling processor into the GIQ. This is really only - * necessary from a secondary thread as the OF start-cpu interface - * performs this function for us on primary threads. - * - * XXX: undo of teardown on kexec needs this too, as may hotplug - */ - rtas_set_indicator_fast(GLOBAL_INTERRUPT_QUEUE, - (1UL << interrupt_server_size) - 1 - default_distrib_server, 1); + xics_set_cpu_giq(default_distrib_server, 1); } void xics_teardown_cpu(void) @@ -749,9 +748,7 @@ void xics_teardown_cpu(void) xics_set_cpu_priority(0); - /* - * Clear IPI - */ + /* Clear any pending IPI request */ if (firmware_has_feature(FW_FEATURE_LPAR)) lpar_qirr_info(cpu, 0xff); else @@ -785,9 +782,7 @@ void xics_kexec_teardown_cpu(int secondary) * so leave the master cpu in the group. */ if (secondary) - rtas_set_indicator_fast(GLOBAL_INTERRUPT_QUEUE, - (1UL << interrupt_server_size) - 1 - - default_distrib_server, 0); + xics_set_cpu_giq(default_distrib_server, 0); } #ifdef CONFIG_HOTPLUG_CPU @@ -795,7 +790,6 @@ void xics_kexec_teardown_cpu(int secondary) /* Interrupts are disabled. */ void xics_migrate_irqs_away(void) { - int status; int cpu = smp_processor_id(), hw_cpu = hard_smp_processor_id(); unsigned int irq, virq; @@ -806,10 +800,8 @@ void xics_migrate_irqs_away(void) /* Reject any interrupt that was queued to us... */ xics_set_cpu_priority(0); - /* remove ourselves from the global interrupt queue */ - status = rtas_set_indicator_fast(GLOBAL_INTERRUPT_QUEUE, - (1UL << interrupt_server_size) - 1 - default_distrib_server, 0); - WARN_ON(status < 0); + /* Remove ourselves from the global interrupt queue */ + xics_set_cpu_giq(default_distrib_server, 0); /* Allow IPIs again... */ xics_set_cpu_priority(DEFAULT_PRIORITY); @@ -817,6 +809,7 @@ void xics_migrate_irqs_away(void) for_each_irq(virq) { struct irq_desc *desc; int xics_status[2]; + int status; unsigned long flags; /* We cant set affinity on ISA interrupts */ -- cgit v1.2.3 From 1a57c926b6da56b4f904a0d8117ac362724f8c66 Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:35 +0000 Subject: powerpc/xics: EOI xics ipi by hand in kexec EOI normally has the side effect of returning the cpu to the base priority to recieve the next interrupt. This is actually controlled by the top byte of the xirr register. When we are exiting the kernel in kexec we must eoi the ipi for the next kernel because we never return from the handler, but we want to leave interrupt delivery blocked until the next kernel takes action. Since the hardware ipi vector is fixed, its easiest to just do the eoi explicitly. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 18 +++++++----------- 1 file changed, 7 insertions(+), 11 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 0bb553331f4..165234d2599 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -757,25 +757,21 @@ void xics_teardown_cpu(void) void xics_kexec_teardown_cpu(int secondary) { - unsigned int ipi; - struct irq_desc *desc; - xics_teardown_cpu(); /* - * we need to EOI the IPI + * we take the ipi irq but and never return so we + * need to EOI the IPI, but want to leave our priority 0 * - * probably need to check all the other interrupts too + * should we check all the other interrupts too? * should we be flagging idle loop instead? * or creating some task to be scheduled? */ - ipi = irq_find_mapping(xics_host, XICS_IPI); - if (ipi == XICS_IRQ_SPURIOUS) - return; - desc = get_irq_desc(ipi); - if (desc->chip && desc->chip->eoi) - desc->chip->eoi(ipi); + if (firmware_has_feature(FW_FEATURE_LPAR)) + lpar_xirr_info_set((0x00 << 24) | XICS_IPI); + else + direct_xirr_info_set((0x00 << 24) | XICS_IPI); /* * Some machines need to have at least one cpu in the GIQ, -- cgit v1.2.3 From d879f3849c93743e170a8dc60a8dfb66150c420d Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:39 +0000 Subject: powerpc/xics: Mark xics IPI interrupt as per-cpu It is physically per-cpu, and we want the irq layer to treat it that way. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 165234d2599..5ba3e009296 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -556,11 +556,11 @@ static void xics_request_ipi(void) */ set_irq_handler(ipi, handle_percpu_irq); if (firmware_has_feature(FW_FEATURE_LPAR)) - rc = request_irq(ipi, xics_ipi_action_lpar, IRQF_DISABLED, - "IPI", NULL); + rc = request_irq(ipi, xics_ipi_action_lpar, + IRQF_DISABLED|IRQF_PERCPU, "IPI", NULL); else - rc = request_irq(ipi, xics_ipi_action_direct, IRQF_DISABLED, - "IPI", NULL); + rc = request_irq(ipi, xics_ipi_action_direct, + IRQF_DISABLED|IRQF_PERCPU, "IPI", NULL); BUG_ON(rc); } -- cgit v1.2.3 From 2172fe8704a1df7cbb988ae1ec4edbfef3e28860 Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:39 +0000 Subject: powerpc/xics: Make printk format strings fit on one line Several printks were broken at word boundaries for line length. Some even referred to old function names. Using __func__ and changing the text slightly for the format allows these printk formats to fit on one line. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 36 +++++++++++++++++------------------ 1 file changed, 18 insertions(+), 18 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 5ba3e009296..62b0400577d 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -201,17 +201,17 @@ static void xics_unmask_irq(unsigned int virq) call_status = rtas_call(ibm_set_xive, 3, 1, NULL, irq, server, DEFAULT_PRIORITY); if (call_status != 0) { - printk(KERN_ERR "xics_enable_irq: irq=%u: ibm_set_xive " - "returned %d\n", irq, call_status); - printk("set_xive %x, server %x\n", ibm_set_xive, server); + printk(KERN_ERR + "%s: ibm_set_xive irq %u server %x returned %d\n", + __func__, irq, server, call_status); return; } /* Now unmask the interrupt (often a no-op) */ call_status = rtas_call(ibm_int_on, 1, 1, NULL, irq); if (call_status != 0) { - printk(KERN_ERR "xics_enable_irq: irq=%u: ibm_int_on " - "returned %d\n", irq, call_status); + printk(KERN_ERR "%s: ibm_int_on irq=%u returned %d\n", + __func__, irq, call_status); return; } } @@ -232,8 +232,8 @@ static void xics_mask_real_irq(unsigned int irq) call_status = rtas_call(ibm_int_off, 1, 1, NULL, irq); if (call_status != 0) { - printk(KERN_ERR "xics_disable_real_irq: irq=%u: " - "ibm_int_off returned %d\n", irq, call_status); + printk(KERN_ERR "%s: ibm_int_off irq=%u returned %d\n", + __func__, irq, call_status); return; } @@ -241,8 +241,8 @@ static void xics_mask_real_irq(unsigned int irq) call_status = rtas_call(ibm_set_xive, 3, 1, NULL, irq, default_server, 0xff); if (call_status != 0) { - printk(KERN_ERR "xics_disable_irq: irq=%u: ibm_set_xive(0xff)" - " returned %d\n", irq, call_status); + printk(KERN_ERR "%s: ibm_set_xive(0xff) irq=%u returned %d\n", + __func__, irq, call_status); return; } } @@ -346,8 +346,8 @@ static void xics_set_affinity(unsigned int virq, cpumask_t cpumask) status = rtas_call(ibm_get_xive, 1, 3, xics_status, irq); if (status) { - printk(KERN_ERR "xics_set_affinity: irq=%u ibm,get-xive " - "returns %d\n", irq, status); + printk(KERN_ERR "%s: ibm,get-xive irq=%u returns %d\n", + __func__, irq, status); return; } @@ -359,8 +359,9 @@ static void xics_set_affinity(unsigned int virq, cpumask_t cpumask) if (irq_server == -1) { char cpulist[128]; cpumask_scnprintf(cpulist, sizeof(cpulist), cpumask); - printk(KERN_WARNING "xics_set_affinity: No online cpus in " - "the mask %s for irq %d\n", cpulist, virq); + printk(KERN_WARNING + "%s: No online cpus in the mask %s for irq %d\n", + __func__, cpulist, virq); return; } @@ -368,8 +369,8 @@ static void xics_set_affinity(unsigned int virq, cpumask_t cpumask) irq, irq_server, xics_status[1]); if (status) { - printk(KERN_ERR "xics_set_affinity: irq=%u ibm,set-xive " - "returns %d\n", irq, status); + printk(KERN_ERR "%s: ibm,set-xive irq=%u returns %d\n", + __func__, irq, status); return; } } @@ -829,9 +830,8 @@ void xics_migrate_irqs_away(void) status = rtas_call(ibm_get_xive, 1, 3, xics_status, irq); if (status) { - printk(KERN_ERR "migrate_irqs_away: irq=%u " - "ibm,get-xive returns %d\n", - virq, status); + printk(KERN_ERR "%s: ibm,get-xive irq=%u returns %d\n", + __func__, irq, status); goto unlock; } -- cgit v1.2.3 From 199f45c45e8d4f58a5f568464be933534460eb82 Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:44 +0000 Subject: powerpc/xics: Reduce and comment xics IPI use of memory barriers A single full sync (mb()) is requrired to order the mmio to the qirr reg with the set or clear of the message word. However, test_and_clear_bit has the effect of smp_mb() and we are not doing any other io from here, so we don't need a mb per bit processed. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/pseries/xics.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c index 62b0400577d..e1904774a70 100644 --- a/arch/powerpc/platforms/pseries/xics.c +++ b/arch/powerpc/platforms/pseries/xics.c @@ -498,26 +498,23 @@ static irqreturn_t xics_ipi_dispatch(int cpu) { WARN_ON(cpu_is_offline(cpu)); + mb(); /* order mmio clearing qirr */ while (xics_ipi_message[cpu].value) { if (test_and_clear_bit(PPC_MSG_CALL_FUNCTION, &xics_ipi_message[cpu].value)) { - mb(); smp_message_recv(PPC_MSG_CALL_FUNCTION); } if (test_and_clear_bit(PPC_MSG_RESCHEDULE, &xics_ipi_message[cpu].value)) { - mb(); smp_message_recv(PPC_MSG_RESCHEDULE); } if (test_and_clear_bit(PPC_MSG_CALL_FUNC_SINGLE, &xics_ipi_message[cpu].value)) { - mb(); smp_message_recv(PPC_MSG_CALL_FUNC_SINGLE); } #if defined(CONFIG_DEBUGGER) || defined(CONFIG_KEXEC) if (test_and_clear_bit(PPC_MSG_DEBUGGER_BREAK, &xics_ipi_message[cpu].value)) { - mb(); smp_message_recv(PPC_MSG_DEBUGGER_BREAK); } #endif -- cgit v1.2.3 From 22d660ffd0db8d136b122751287d186e869ca474 Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 01:56:45 +0000 Subject: powerpc/smp: No need to set_need_resched when getting a resched IPI The comment in the code was asking "Do we have to do this?", and according to x86 and s390 the answer is no, the scheduler will do it before calling the arch hook. Signed-off-by: Milton Miller Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/smp.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/smp.c b/arch/powerpc/kernel/smp.c index 5337ca7bb64..3ee736fa8b1 100644 --- a/arch/powerpc/kernel/smp.c +++ b/arch/powerpc/kernel/smp.c @@ -101,8 +101,7 @@ void smp_message_recv(int msg) generic_smp_call_function_interrupt(); break; case PPC_MSG_RESCHEDULE: - /* XXX Do we have to do this? */ - set_need_resched(); + /* we notice need_resched on exit */ break; case PPC_MSG_CALL_FUNC_SINGLE: generic_smp_call_function_single_interrupt(); -- cgit v1.2.3 From 92ae954046b1434c8c11468893ed27c7c06f2c21 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Thu, 2 Oct 2008 03:58:08 -0500 Subject: powerpc/85xx: Wire up RTC interrupt on MPC8536DS Add interrupt info to the MPC8536DS .dts for the RTC Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8536ds.dts | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mpc8536ds.dts b/arch/powerpc/boot/dts/mpc8536ds.dts index 1505d6855ef..93fdd99901b 100644 --- a/arch/powerpc/boot/dts/mpc8536ds.dts +++ b/arch/powerpc/boot/dts/mpc8536ds.dts @@ -91,6 +91,8 @@ rtc@68 { compatible = "dallas,ds3232"; reg = <0x68>; + interrupts = <0 0x1>; + interrupt-parent = <&mpic>; }; }; -- cgit v1.2.3 From 3a470247913e6537c453937720b61f4ecc3e39db Mon Sep 17 00:00:00 2001 From: Martyn Welch Date: Wed, 1 Oct 2008 09:32:39 +0100 Subject: powerpc: GE Fanuc's FPGA based PIC controller on the SBC610 Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D). A number of MPC8641D based route interrupts for on-board interrupts through a FPGA based interrupt controller, which is chained with the MPC8641D's mpic. This patch provides a basic driver to allow basic routing of interrupts to the mpic. Signed-off-by: Martyn Welch Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/gef_sbc610.dts | 37 ++++- arch/powerpc/platforms/86xx/Makefile | 2 +- arch/powerpc/platforms/86xx/gef_pic.c | 258 +++++++++++++++++++++++++++++++ arch/powerpc/platforms/86xx/gef_pic.h | 11 ++ arch/powerpc/platforms/86xx/gef_sbc610.c | 25 ++- 5 files changed, 327 insertions(+), 6 deletions(-) create mode 100644 arch/powerpc/platforms/86xx/gef_pic.c create mode 100644 arch/powerpc/platforms/86xx/gef_pic.h (limited to 'arch') diff --git a/arch/powerpc/boot/dts/gef_sbc610.dts b/arch/powerpc/boot/dts/gef_sbc610.dts index 80b79e4adc7..771a776d610 100644 --- a/arch/powerpc/boot/dts/gef_sbc610.dts +++ b/arch/powerpc/boot/dts/gef_sbc610.dts @@ -67,6 +67,35 @@ reg = <0x0 0x40000000>; // set by uboot }; + localbus@fef05000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc8641-localbus", "simple-bus"; + reg = <0xf8005000 0x1000>; + interrupts = <19 2>; + interrupt-parent = <&mpic>; + + ranges = <0 0 0xff000000 0x01000000 // 16MB Boot flash + 1 0 0xe8000000 0x08000000 // Paged Flash 0 + 2 0 0xe0000000 0x08000000 // Paged Flash 1 + 3 0 0xfc100000 0x00020000 // NVRAM + 4 0 0xfc000000 0x00008000 // FPGA + 5 0 0xfc008000 0x00008000 // AFIX FPGA + 6 0 0xfd000000 0x00800000 // IO FPGA (8-bit) + 7 0 0xfd800000 0x00800000>; // IO FPGA (32-bit) + + gef_pic: pic@4,4000 { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "gef,fpga-pic"; + reg = <0x4 0x4000 0x20>; + interrupts = <0x8 + 0x9>; + interrupt-parent = <&mpic>; + + }; + }; + soc@fef00000 { #address-cells = <1>; #size-cells = <1>; @@ -150,13 +179,13 @@ reg = <0x24520 0x20>; phy0: ethernet-phy@0 { - interrupt-parent = <&mpic>; - interrupts = <0x0 0x1>; + interrupt-parent = <&gef_pic>; + interrupts = <0x9 0x4>; reg = <1>; }; phy2: ethernet-phy@2 { - interrupt-parent = <&mpic>; - interrupts = <0x0 0x1>; + interrupt-parent = <&gef_pic>; + interrupts = <0x8 0x4>; reg = <3>; }; }; diff --git a/arch/powerpc/platforms/86xx/Makefile b/arch/powerpc/platforms/86xx/Makefile index cb9fc8f4360..4a56ff619af 100644 --- a/arch/powerpc/platforms/86xx/Makefile +++ b/arch/powerpc/platforms/86xx/Makefile @@ -7,4 +7,4 @@ obj-$(CONFIG_SMP) += mpc86xx_smp.o obj-$(CONFIG_MPC8641_HPCN) += mpc86xx_hpcn.o obj-$(CONFIG_SBC8641D) += sbc8641d.o obj-$(CONFIG_MPC8610_HPCD) += mpc8610_hpcd.o -obj-$(CONFIG_GEF_SBC610) += gef_sbc610.o +obj-$(CONFIG_GEF_SBC610) += gef_sbc610.o gef_pic.o diff --git a/arch/powerpc/platforms/86xx/gef_pic.c b/arch/powerpc/platforms/86xx/gef_pic.c new file mode 100644 index 00000000000..50d0a2b6380 --- /dev/null +++ b/arch/powerpc/platforms/86xx/gef_pic.c @@ -0,0 +1,258 @@ +/* + * Interrupt handling for GE Fanuc's FPGA based PIC + * + * Author: Martyn Welch + * + * 2008 (c) GE Fanuc Intelligent Platforms Embedded Systems, Inc. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include "gef_pic.h" + +#define DEBUG +#undef DEBUG + +#ifdef DEBUG +#define DBG(fmt...) do { printk(KERN_DEBUG "gef_pic: " fmt); } while (0) +#else +#define DBG(fmt...) do { } while (0) +#endif + +#define GEF_PIC_NUM_IRQS 32 + +/* Interrupt Controller Interface Registers */ +#define GEF_PIC_INTR_STATUS 0x0000 + +#define GEF_PIC_INTR_MASK(cpu) (0x0010 + (0x4 * cpu)) +#define GEF_PIC_CPU0_INTR_MASK GEF_PIC_INTR_MASK(0) +#define GEF_PIC_CPU1_INTR_MASK GEF_PIC_INTR_MASK(1) + +#define GEF_PIC_MCP_MASK(cpu) (0x0018 + (0x4 * cpu)) +#define GEF_PIC_CPU0_MCP_MASK GEF_PIC_MCP_MASK(0) +#define GEF_PIC_CPU1_MCP_MASK GEF_PIC_MCP_MASK(1) + +#define gef_irq_to_hw(virq) ((unsigned int)irq_map[virq].hwirq) + + +static DEFINE_SPINLOCK(gef_pic_lock); + +static void __iomem *gef_pic_irq_reg_base; +static struct irq_host *gef_pic_irq_host; +static int gef_pic_cascade_irq; + +/* + * Interrupt Controller Handling + * + * The interrupt controller handles interrupts for most on board interrupts, + * apart from PCI interrupts. For example on SBC610: + * + * 17:31 RO Reserved + * 16 RO PCI Express Doorbell 3 Status + * 15 RO PCI Express Doorbell 2 Status + * 14 RO PCI Express Doorbell 1 Status + * 13 RO PCI Express Doorbell 0 Status + * 12 RO Real Time Clock Interrupt Status + * 11 RO Temperature Interrupt Status + * 10 RO Temperature Critical Interrupt Status + * 9 RO Ethernet PHY1 Interrupt Status + * 8 RO Ethernet PHY3 Interrupt Status + * 7 RO PEX8548 Interrupt Status + * 6 RO Reserved + * 5 RO Watchdog 0 Interrupt Status + * 4 RO Watchdog 1 Interrupt Status + * 3 RO AXIS Message FIFO A Interrupt Status + * 2 RO AXIS Message FIFO B Interrupt Status + * 1 RO AXIS Message FIFO C Interrupt Status + * 0 RO AXIS Message FIFO D Interrupt Status + * + * Interrupts can be forwarded to one of two output lines. Nothing + * clever is done, so if the masks are incorrectly set, a single input + * interrupt could generate interrupts on both output lines! + * + * The dual lines are there to allow the chained interrupts to be easily + * passed into two different cores. We currently do not use this functionality + * in this driver. + * + * Controller can also be configured to generate Machine checks (MCP), again on + * two lines, to be attached to two different cores. It is suggested that these + * should be masked out. + */ + +void gef_pic_cascade(unsigned int irq, struct irq_desc *desc) +{ + unsigned int cascade_irq; + + /* + * See if we actually have an interrupt, call generic handling code if + * we do. + */ + cascade_irq = gef_pic_get_irq(); + + if (cascade_irq != NO_IRQ) + generic_handle_irq(cascade_irq); + + desc->chip->eoi(irq); + +} + +static void gef_pic_mask(unsigned int virq) +{ + unsigned long flags; + unsigned int hwirq; + u32 mask; + + hwirq = gef_irq_to_hw(virq); + + spin_lock_irqsave(&gef_pic_lock, flags); + mask = in_be32(gef_pic_irq_reg_base + GEF_PIC_INTR_MASK(0)); + mask &= ~(1 << hwirq); + out_be32(gef_pic_irq_reg_base + GEF_PIC_INTR_MASK(0), mask); + spin_unlock_irqrestore(&gef_pic_lock, flags); +} + +static void gef_pic_mask_ack(unsigned int virq) +{ + /* Don't think we actually have to do anything to ack an interrupt, + * we just need to clear down the devices interrupt and it will go away + */ + gef_pic_mask(virq); +} + +static void gef_pic_unmask(unsigned int virq) +{ + unsigned long flags; + unsigned int hwirq; + u32 mask; + + hwirq = gef_irq_to_hw(virq); + + spin_lock_irqsave(&gef_pic_lock, flags); + mask = in_be32(gef_pic_irq_reg_base + GEF_PIC_INTR_MASK(0)); + mask |= (1 << hwirq); + out_be32(gef_pic_irq_reg_base + GEF_PIC_INTR_MASK(0), mask); + spin_unlock_irqrestore(&gef_pic_lock, flags); +} + +static struct irq_chip gef_pic_chip = { + .typename = "gefp", + .mask = gef_pic_mask, + .mask_ack = gef_pic_mask_ack, + .unmask = gef_pic_unmask, +}; + + +/* When an interrupt is being configured, this call allows some flexibilty + * in deciding which irq_chip structure is used + */ +static int gef_pic_host_map(struct irq_host *h, unsigned int virq, + irq_hw_number_t hwirq) +{ + /* All interrupts are LEVEL sensitive */ + get_irq_desc(virq)->status |= IRQ_LEVEL; + set_irq_chip_and_handler(virq, &gef_pic_chip, handle_level_irq); + + return 0; +} + +static int gef_pic_host_xlate(struct irq_host *h, struct device_node *ct, + u32 *intspec, unsigned int intsize, + irq_hw_number_t *out_hwirq, unsigned int *out_flags) +{ + + *out_hwirq = intspec[0]; + if (intsize > 1) + *out_flags = intspec[1]; + else + *out_flags = IRQ_TYPE_LEVEL_HIGH; + + return 0; +} + +static struct irq_host_ops gef_pic_host_ops = { + .map = gef_pic_host_map, + .xlate = gef_pic_host_xlate, +}; + + +/* + * Initialisation of PIC, this should be called in BSP + */ +void __init gef_pic_init(struct device_node *np) +{ + unsigned long flags; + + /* Map the devices registers into memory */ + gef_pic_irq_reg_base = of_iomap(np, 0); + + spin_lock_irqsave(&gef_pic_lock, flags); + + /* Initialise everything as masked. */ + out_be32(gef_pic_irq_reg_base + GEF_PIC_CPU0_INTR_MASK, 0); + out_be32(gef_pic_irq_reg_base + GEF_PIC_CPU1_INTR_MASK, 0); + + out_be32(gef_pic_irq_reg_base + GEF_PIC_CPU0_MCP_MASK, 0); + out_be32(gef_pic_irq_reg_base + GEF_PIC_CPU1_MCP_MASK, 0); + + spin_unlock_irqrestore(&gef_pic_lock, flags); + + /* Map controller */ + gef_pic_cascade_irq = irq_of_parse_and_map(np, 0); + if (gef_pic_cascade_irq == NO_IRQ) { + printk(KERN_ERR "SBC610: failed to map cascade interrupt"); + return; + } + + /* Setup an irq_host structure */ + gef_pic_irq_host = irq_alloc_host(np, IRQ_HOST_MAP_LINEAR, + GEF_PIC_NUM_IRQS, + &gef_pic_host_ops, NO_IRQ); + if (gef_pic_irq_host == NULL) + return; + + /* Chain with parent controller */ + set_irq_chained_handler(gef_pic_cascade_irq, gef_pic_cascade); +} + +/* + * This is called when we receive an interrupt with apparently comes from this + * chip - check, returning the highest interrupt generated or return NO_IRQ + */ +unsigned int gef_pic_get_irq(void) +{ + u32 cause, mask, active; + unsigned int virq = NO_IRQ; + int hwirq; + + cause = in_be32(gef_pic_irq_reg_base + GEF_PIC_INTR_STATUS); + + mask = in_be32(gef_pic_irq_reg_base + GEF_PIC_INTR_MASK(0)); + + active = cause & mask; + + if (active) { + for (hwirq = GEF_PIC_NUM_IRQS - 1; hwirq > -1; hwirq--) { + if (active & (0x1 << hwirq)) + break; + } + virq = irq_linear_revmap(gef_pic_irq_host, + (irq_hw_number_t)hwirq); + } + + return virq; +} + diff --git a/arch/powerpc/platforms/86xx/gef_pic.h b/arch/powerpc/platforms/86xx/gef_pic.h new file mode 100644 index 00000000000..6149916da3f --- /dev/null +++ b/arch/powerpc/platforms/86xx/gef_pic.h @@ -0,0 +1,11 @@ +#ifndef __GEF_PIC_H__ +#define __GEF_PIC_H__ + +#include + +void gef_pic_cascade(unsigned int, struct irq_desc *); +unsigned int gef_pic_get_irq(void); +void gef_pic_init(struct device_node *); + +#endif /* __GEF_PIC_H__ */ + diff --git a/arch/powerpc/platforms/86xx/gef_sbc610.c b/arch/powerpc/platforms/86xx/gef_sbc610.c index ee215002b1c..3873c2018cc 100644 --- a/arch/powerpc/platforms/86xx/gef_sbc610.c +++ b/arch/powerpc/platforms/86xx/gef_sbc610.c @@ -39,6 +39,7 @@ #include #include "mpc86xx.h" +#include "gef_pic.h" #undef DEBUG @@ -48,6 +49,28 @@ #define DBG (fmt...) do { } while (0) #endif +void __iomem *sbc610_regs; + +static void __init gef_sbc610_init_irq(void) +{ + struct device_node *cascade_node = NULL; + + mpc86xx_init_irq(); + + /* + * There is a simple interrupt handler in the main FPGA, this needs + * to be cascaded into the MPIC + */ + cascade_node = of_find_compatible_node(NULL, NULL, "gef,fpga-pic"); + if (!cascade_node) { + printk(KERN_WARNING "SBC610: No FPGA PIC\n"); + return; + } + + gef_pic_init(cascade_node); + of_node_put(cascade_node); +} + static void __init gef_sbc610_setup_arch(void) { #ifdef CONFIG_PCI @@ -145,7 +168,7 @@ define_machine(gef_sbc610) { .name = "GE Fanuc SBC610", .probe = gef_sbc610_probe, .setup_arch = gef_sbc610_setup_arch, - .init_IRQ = mpc86xx_init_irq, + .init_IRQ = gef_sbc610_init_irq, .show_cpuinfo = gef_sbc610_show_cpuinfo, .get_irq = mpic_get_irq, .restart = fsl_rstcr_restart, -- cgit v1.2.3 From 4e330bcf6b323fcff0e3224c5db77cbcca83a878 Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Fri, 3 Oct 2008 11:14:10 -0500 Subject: powerpc: make Freescale QE support a selectable Kconfig option Modify the Kconfig so that Freescale QUICC Engine (QE) support is a selectable option, thereby allowing users to compile kernels without any QE support. The drawback is that QE support is now disabled by default on platforms that have a QE, and so a defconfig is needed to enable QE and QE devices (like UCC GETH). Fortunately, all the current relevant defconfigs do that already. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala --- arch/powerpc/platforms/83xx/Kconfig | 5 ----- arch/powerpc/platforms/85xx/Kconfig | 1 - arch/powerpc/platforms/Kconfig | 3 ++- 3 files changed, 2 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/83xx/Kconfig b/arch/powerpc/platforms/83xx/Kconfig index 6159c5d4e5f..83c664afc89 100644 --- a/arch/powerpc/platforms/83xx/Kconfig +++ b/arch/powerpc/platforms/83xx/Kconfig @@ -19,7 +19,6 @@ config MPC831x_RDB config MPC832x_MDS bool "Freescale MPC832x MDS" select DEFAULT_UIMAGE - select QUICC_ENGINE select PPC_MPC832x help This option enables support for the MPC832x MDS evaluation board. @@ -27,7 +26,6 @@ config MPC832x_MDS config MPC832x_RDB bool "Freescale MPC832x RDB" select DEFAULT_UIMAGE - select QUICC_ENGINE select PPC_MPC832x help This option enables support for the MPC8323 RDB board. @@ -57,15 +55,12 @@ config MPC834x_ITX config MPC836x_MDS bool "Freescale MPC836x MDS" select DEFAULT_UIMAGE - select QUICC_ENGINE help This option enables support for the MPC836x MDS Processor Board. config MPC836x_RDK bool "Freescale/Logic MPC836x RDK" select DEFAULT_UIMAGE - select QUICC_ENGINE - select QE_GPIO select FSL_GTM select FSL_LBC help diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig index 291675b0097..b79dc710ed3 100644 --- a/arch/powerpc/platforms/85xx/Kconfig +++ b/arch/powerpc/platforms/85xx/Kconfig @@ -33,7 +33,6 @@ config MPC85xx_CDS config MPC85xx_MDS bool "Freescale MPC85xx MDS" select DEFAULT_UIMAGE - select QUICC_ENGINE select PHYLIB help This option enables support for the MPC85xx MDS board diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig index 9578c45b04f..6cf517f5fba 100644 --- a/arch/powerpc/platforms/Kconfig +++ b/arch/powerpc/platforms/Kconfig @@ -239,7 +239,8 @@ config TAU_AVERAGE If in doubt, say N here. config QUICC_ENGINE - bool + bool "Freescale QUICC Engine (QE) Support" + depends on FSL_SOC select PPC_LIB_RHEAP select CRC32 help -- cgit v1.2.3 From 5c091193e4a12e88930a0bb3ed3632c51e926a76 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Fri, 3 Oct 2008 23:40:36 +0400 Subject: powerpc/QE: move QE_GPIO Kconfig symbol into the platforms/Kconfig Specifying user-selectable option in the qe_lib/Kconfig was a bad idea because the qe_lib/Kconfig is included into the top level Kconfig, and thus the QE_GPIO option appears at the top level menu. This patch effectively moves the QE_GPIO option under the platform menu instead. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/platforms/Kconfig | 9 +++++++++ arch/powerpc/sysdev/qe_lib/Kconfig | 9 --------- 2 files changed, 9 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig index 6cf517f5fba..47e956c871f 100644 --- a/arch/powerpc/platforms/Kconfig +++ b/arch/powerpc/platforms/Kconfig @@ -249,6 +249,15 @@ config QUICC_ENGINE Selecting this option means that you wish to build a kernel for a machine with a QE coprocessor. +config QE_GPIO + bool "QE GPIO support" + depends on QUICC_ENGINE + select GENERIC_GPIO + select ARCH_REQUIRE_GPIOLIB + help + Say Y here if you're going to use hardware that connects to the + QE GPIOs. + config CPM2 bool "Enable support for the CPM2 (Communications Processor Module)" depends on MPC85xx || 8260 diff --git a/arch/powerpc/sysdev/qe_lib/Kconfig b/arch/powerpc/sysdev/qe_lib/Kconfig index 1ce546462be..76ffbc48d4b 100644 --- a/arch/powerpc/sysdev/qe_lib/Kconfig +++ b/arch/powerpc/sysdev/qe_lib/Kconfig @@ -24,12 +24,3 @@ config QE_USB bool help QE USB Host Controller support - -config QE_GPIO - bool "QE GPIO support" - depends on QUICC_ENGINE - select GENERIC_GPIO - select ARCH_REQUIRE_GPIOLIB - help - Say Y here if you're going to use hardware that connects to the - QE GPIOs. -- cgit v1.2.3 From 62666828bae7057835d982367e98716a1bd0fd40 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Mon, 6 Oct 2008 21:08:39 +0400 Subject: powerpc/83xx: don't probe broken PCI on mpc837x_mds boards In the standalone setup the board's CPLD disables the PCI internal arbiter, thus any access to the PCI bus will hang the board. The common way to disable particular devices in the device tree is to put the "status" property with any value other than "ok" or "okay" into the device node we want to disable. So, when there is no PCI arbiter on the bus the u-boot adds status = "broken (no arbiter)" property into the PCI controller's node, and so marks the PCI controller as unavailable. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/platforms/83xx/mpc837x_mds.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/83xx/mpc837x_mds.c b/arch/powerpc/platforms/83xx/mpc837x_mds.c index be62de23bea..8bb13c80714 100644 --- a/arch/powerpc/platforms/83xx/mpc837x_mds.c +++ b/arch/powerpc/platforms/83xx/mpc837x_mds.c @@ -85,8 +85,14 @@ static void __init mpc837x_mds_setup_arch(void) ppc_md.progress("mpc837x_mds_setup_arch()", 0); #ifdef CONFIG_PCI - for_each_compatible_node(np, "pci", "fsl,mpc8349-pci") + for_each_compatible_node(np, "pci", "fsl,mpc8349-pci") { + if (!of_device_is_available(np)) { + pr_warning("%s: disabled by the firmware.\n", + np->full_name); + continue; + } mpc83xx_add_bridge(np); + } #endif mpc837xmds_usb_cfg(); } -- cgit v1.2.3 From 4a015c37409ead893b659c2f89f1aa1fdf512115 Mon Sep 17 00:00:00 2001 From: John Rigby Date: Tue, 7 Oct 2008 13:00:20 -0600 Subject: powerpc/fsl: Hide MPC5121 pci bridge. The class of the MPC5121 pci host bridge is PCI_CLASS_BRIDGE_OTHER while other freescale host bridges have class set to PCI_CLASS_PROCESSOR_POWERPC. This patch makes fixup_hide_host_resource_fsl match PCI_CLASS_BRIDGE_OTHER in addition to PCI_CLASS_PROCESSOR_POWERPC. Signed-off-by: John Rigby Signed-off-by: Kumar Gala --- arch/powerpc/kernel/pci_32.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/pci_32.c b/arch/powerpc/kernel/pci_32.c index 174b77ee18f..a848c6360bd 100644 --- a/arch/powerpc/kernel/pci_32.c +++ b/arch/powerpc/kernel/pci_32.c @@ -54,11 +54,12 @@ LIST_HEAD(hose_list); static int pci_bus_count; static void -fixup_hide_host_resource_fsl(struct pci_dev* dev) +fixup_hide_host_resource_fsl(struct pci_dev *dev) { int i, class = dev->class >> 8; - if ((class == PCI_CLASS_PROCESSOR_POWERPC) && + if ((class == PCI_CLASS_PROCESSOR_POWERPC || + class == PCI_CLASS_BRIDGE_OTHER) && (dev->hdr_type == PCI_HEADER_TYPE_NORMAL) && (dev->bus->parent == NULL)) { for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) { -- cgit v1.2.3 From 5b70a097052fff3831d8b94541452e7c29426777 Mon Sep 17 00:00:00 2001 From: John Rigby Date: Tue, 7 Oct 2008 13:00:18 -0600 Subject: powerpc: 83xx: pci: Remove need for get_immrbase from mpc83xx_add_bridge. Modify mpc83xx_add_bridge to get config space register base address from the device tree instead of immr + hardcoded offset. 83xx pci nodes have this change: register properties now contain two address length tuples: First is the pci bridge register base, this has always been there. Second is the config base, this is new. This is documented in dts-bindings/fsl/83xx-512x-pci.txt The changes accomplish these things: mpc83xx_add_bridge no longer needs to call get_immrbase it uses hard coded addresses if the second register value is missing Signed-off-by: John Rigby Signed-off-by: Kumar Gala --- .../powerpc/dts-bindings/fsl/83xx-512x-pci.txt | 40 ++++++++++++++++ arch/powerpc/boot/dts/mpc8313erdb.dts | 3 +- arch/powerpc/boot/dts/mpc8315erdb.dts | 3 +- arch/powerpc/boot/dts/mpc832x_mds.dts | 3 +- arch/powerpc/boot/dts/mpc832x_rdb.dts | 3 +- arch/powerpc/boot/dts/mpc8349emitx.dts | 6 ++- arch/powerpc/boot/dts/mpc8349emitxgp.dts | 3 +- arch/powerpc/boot/dts/mpc834x_mds.dts | 6 ++- arch/powerpc/boot/dts/mpc836x_mds.dts | 3 +- arch/powerpc/boot/dts/mpc836x_rdk.dts | 3 +- arch/powerpc/boot/dts/mpc8377_mds.dts | 3 +- arch/powerpc/boot/dts/mpc8377_rdb.dts | 3 +- arch/powerpc/boot/dts/mpc8378_mds.dts | 3 +- arch/powerpc/boot/dts/mpc8378_rdb.dts | 3 +- arch/powerpc/boot/dts/mpc8379_mds.dts | 3 +- arch/powerpc/boot/dts/mpc8379_rdb.dts | 3 +- arch/powerpc/boot/dts/sbc8349.dts | 3 +- arch/powerpc/sysdev/fsl_pci.c | 54 ++++++++++++++-------- 18 files changed, 111 insertions(+), 37 deletions(-) create mode 100644 Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt (limited to 'arch') diff --git a/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt b/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt new file mode 100644 index 00000000000..35a46536240 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt @@ -0,0 +1,40 @@ +* Freescale 83xx and 512x PCI bridges + +Freescale 83xx and 512x SOCs include the same pci bridge core. + +83xx/512x specific notes: +- reg: should contain two address length tuples + The first is for the internal pci bridge registers + The second is for the pci config space access registers + +Example (MPC8313ERDB) + pci0: pci@e0008500 { + cell-index = <1>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + /* IDSEL 0x0E -mini PCI */ + 0x7000 0x0 0x0 0x1 &ipic 18 0x8 + 0x7000 0x0 0x0 0x2 &ipic 18 0x8 + 0x7000 0x0 0x0 0x3 &ipic 18 0x8 + 0x7000 0x0 0x0 0x4 &ipic 18 0x8 + + /* IDSEL 0x0F - PCI slot */ + 0x7800 0x0 0x0 0x1 &ipic 17 0x8 + 0x7800 0x0 0x0 0x2 &ipic 18 0x8 + 0x7800 0x0 0x0 0x3 &ipic 17 0x8 + 0x7800 0x0 0x0 0x4 &ipic 18 0x8>; + interrupt-parent = <&ipic>; + interrupts = <66 0x8>; + bus-range = <0x0 0x0>; + ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 + 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 + 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; + clock-frequency = <66666666>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ + compatible = "fsl,mpc8349-pci"; + device_type = "pci"; + }; diff --git a/arch/powerpc/boot/dts/mpc8313erdb.dts b/arch/powerpc/boot/dts/mpc8313erdb.dts index 539085591e0..747f2767633 100644 --- a/arch/powerpc/boot/dts/mpc8313erdb.dts +++ b/arch/powerpc/boot/dts/mpc8313erdb.dts @@ -363,7 +363,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc8315erdb.dts b/arch/powerpc/boot/dts/mpc8315erdb.dts index 94c9b4107a1..7449e54c1a9 100644 --- a/arch/powerpc/boot/dts/mpc8315erdb.dts +++ b/arch/powerpc/boot/dts/mpc8315erdb.dts @@ -318,7 +318,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc832x_mds.dts b/arch/powerpc/boot/dts/mpc832x_mds.dts index 015808ae102..e4cc1768f24 100644 --- a/arch/powerpc/boot/dts/mpc832x_mds.dts +++ b/arch/powerpc/boot/dts/mpc832x_mds.dts @@ -423,7 +423,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc832x_rdb.dts b/arch/powerpc/boot/dts/mpc832x_rdb.dts index b5b0ec2eb88..226ff066652 100644 --- a/arch/powerpc/boot/dts/mpc832x_rdb.dts +++ b/arch/powerpc/boot/dts/mpc832x_rdb.dts @@ -331,7 +331,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc8349emitx.dts b/arch/powerpc/boot/dts/mpc8349emitx.dts index 1327a61d053..5cedf373a1d 100644 --- a/arch/powerpc/boot/dts/mpc8349emitx.dts +++ b/arch/powerpc/boot/dts/mpc8349emitx.dts @@ -254,7 +254,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; @@ -280,7 +281,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008600 0x100>; + reg = <0xe0008600 0x100 /* internal registers */ + 0xe0008380 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc8349emitxgp.dts b/arch/powerpc/boot/dts/mpc8349emitxgp.dts index f70d3a0a6eb..81ae1d3e944 100644 --- a/arch/powerpc/boot/dts/mpc8349emitxgp.dts +++ b/arch/powerpc/boot/dts/mpc8349emitxgp.dts @@ -228,7 +228,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008600 0x100>; + reg = <0xe0008600 0x100 /* internal registers */ + 0xe0008380 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc834x_mds.dts b/arch/powerpc/boot/dts/mpc834x_mds.dts index e29739eee35..04bfde3ea60 100644 --- a/arch/powerpc/boot/dts/mpc834x_mds.dts +++ b/arch/powerpc/boot/dts/mpc834x_mds.dts @@ -315,7 +315,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; @@ -376,7 +377,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008600 0x100>; + reg = <0xe0008600 0x100 /* internal registers */ + 0xe0008380 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts index 49aec71916e..66a12d2631f 100644 --- a/arch/powerpc/boot/dts/mpc836x_mds.dts +++ b/arch/powerpc/boot/dts/mpc836x_mds.dts @@ -426,7 +426,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc836x_rdk.dts b/arch/powerpc/boot/dts/mpc836x_rdk.dts index 69c9bd2acd8..f747747e531 100644 --- a/arch/powerpc/boot/dts/mpc836x_rdk.dts +++ b/arch/powerpc/boot/dts/mpc836x_rdk.dts @@ -409,7 +409,8 @@ #interrupt-cells = <1>; device_type = "pci"; compatible = "fsl,mpc8360-pci", "fsl,mpc8349-pci"; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ ranges = <0x02000000 0 0x90000000 0x90000000 0 0x10000000 0x42000000 0 0x80000000 0x80000000 0 0x10000000 0x01000000 0 0xe0300000 0xe0300000 0 0x00100000>; diff --git a/arch/powerpc/boot/dts/mpc8377_mds.dts b/arch/powerpc/boot/dts/mpc8377_mds.dts index 78f0f1124ff..87314c78b47 100644 --- a/arch/powerpc/boot/dts/mpc8377_mds.dts +++ b/arch/powerpc/boot/dts/mpc8377_mds.dts @@ -378,7 +378,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc8377_rdb.dts b/arch/powerpc/boot/dts/mpc8377_rdb.dts index d46327e8cb6..53191ba67aa 100644 --- a/arch/powerpc/boot/dts/mpc8377_rdb.dts +++ b/arch/powerpc/boot/dts/mpc8377_rdb.dts @@ -319,7 +319,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc8378_mds.dts b/arch/powerpc/boot/dts/mpc8378_mds.dts index c44f30f2f08..02941919598 100644 --- a/arch/powerpc/boot/dts/mpc8378_mds.dts +++ b/arch/powerpc/boot/dts/mpc8378_mds.dts @@ -364,7 +364,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc8378_rdb.dts b/arch/powerpc/boot/dts/mpc8378_rdb.dts index b3e3bd7d550..4a09153d160 100644 --- a/arch/powerpc/boot/dts/mpc8378_rdb.dts +++ b/arch/powerpc/boot/dts/mpc8378_rdb.dts @@ -305,7 +305,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc8379_mds.dts b/arch/powerpc/boot/dts/mpc8379_mds.dts index 653ed47c9a3..13a231144dc 100644 --- a/arch/powerpc/boot/dts/mpc8379_mds.dts +++ b/arch/powerpc/boot/dts/mpc8379_mds.dts @@ -392,7 +392,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/mpc8379_rdb.dts b/arch/powerpc/boot/dts/mpc8379_rdb.dts index 123c8df6f4f..bbd884ac9dc 100644 --- a/arch/powerpc/boot/dts/mpc8379_rdb.dts +++ b/arch/powerpc/boot/dts/mpc8379_rdb.dts @@ -333,7 +333,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/boot/dts/sbc8349.dts b/arch/powerpc/boot/dts/sbc8349.dts index c7f411f7a9a..0f941f310e4 100644 --- a/arch/powerpc/boot/dts/sbc8349.dts +++ b/arch/powerpc/boot/dts/sbc8349.dts @@ -272,7 +272,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0xe0008500 0x100>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ compatible = "fsl,mpc8349-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/sysdev/fsl_pci.c b/arch/powerpc/sysdev/fsl_pci.c index 61e6d77efa4..a3f4abadbad 100644 --- a/arch/powerpc/sysdev/fsl_pci.c +++ b/arch/powerpc/sysdev/fsl_pci.c @@ -1,7 +1,7 @@ /* - * MPC85xx/86xx PCI/PCIE support routing. + * MPC83xx/85xx/86xx PCI/PCIE support routing. * - * Copyright 2007 Freescale Semiconductor, Inc + * Copyright 2007,2008 Freescale Semiconductor, Inc * * Initial author: Xianghua Xiao * Recode: ZHANG WEI @@ -256,15 +256,42 @@ int __init mpc83xx_add_bridge(struct device_node *dev) { int len; struct pci_controller *hose; - struct resource rsrc; + struct resource rsrc_reg; + struct resource rsrc_cfg; const int *bus_range; - int primary = 1, has_address = 0; - phys_addr_t immr = get_immrbase(); + int primary; pr_debug("Adding PCI host bridge %s\n", dev->full_name); /* Fetch host bridge registers address */ - has_address = (of_address_to_resource(dev, 0, &rsrc) == 0); + if (of_address_to_resource(dev, 0, &rsrc_reg)) { + printk(KERN_WARNING "Can't get pci register base!\n"); + return -ENOMEM; + } + + memset(&rsrc_cfg, 0, sizeof(rsrc_cfg)); + + if (of_address_to_resource(dev, 1, &rsrc_cfg)) { + printk(KERN_WARNING + "No pci config register base in dev tree, " + "using default\n"); + /* + * MPC83xx supports up to two host controllers + * one at 0x8500 has config space registers at 0x8300 + * one at 0x8600 has config space registers at 0x8380 + */ + if ((rsrc_reg.start & 0xfffff) == 0x8500) + rsrc_cfg.start = (rsrc_reg.start & 0xfff00000) + 0x8300; + else if ((rsrc_reg.start & 0xfffff) == 0x8600) + rsrc_cfg.start = (rsrc_reg.start & 0xfff00000) + 0x8380; + } + /* + * Controller at offset 0x8500 is primary + */ + if ((rsrc_reg.start & 0xfffff) == 0x8500) + primary = 1; + else + primary = 0; /* Get bus range if any */ bus_range = of_get_property(dev, "bus-range", &len); @@ -281,22 +308,11 @@ int __init mpc83xx_add_bridge(struct device_node *dev) hose->first_busno = bus_range ? bus_range[0] : 0; hose->last_busno = bus_range ? bus_range[1] : 0xff; - /* MPC83xx supports up to two host controllers one at 0x8500 from immrbar - * the other at 0x8600, we consider the 0x8500 the primary controller - */ - /* PCI 1 */ - if ((rsrc.start & 0xfffff) == 0x8500) { - setup_indirect_pci(hose, immr + 0x8300, immr + 0x8304, 0); - } - /* PCI 2 */ - if ((rsrc.start & 0xfffff) == 0x8600) { - setup_indirect_pci(hose, immr + 0x8380, immr + 0x8384, 0); - primary = 0; - } + setup_indirect_pci(hose, rsrc_cfg.start, rsrc_cfg.start + 4, 0); printk(KERN_INFO "Found MPC83xx PCI host bridge at 0x%016llx. " "Firmware bus number: %d->%d\n", - (unsigned long long)rsrc.start, hose->first_busno, + (unsigned long long)rsrc_reg.start, hose->first_busno, hose->last_busno); pr_debug(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n", -- cgit v1.2.3 From 35225802e2e7019392fbff9227662d456eef4e24 Mon Sep 17 00:00:00 2001 From: John Rigby Date: Tue, 7 Oct 2008 15:13:18 -0600 Subject: powerpc/5121: Add PCI support. Uses mpc83xx_add_bridge in fsl_pci.c Adds second register tuple to pci node register property as done for 83xx device trees in a previous patch. Signed-off-by: John Rigby Acked-by: Grant Likely Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc5121ads.dts | 3 ++- arch/powerpc/platforms/512x/Kconfig | 2 ++ arch/powerpc/platforms/512x/mpc5121_ads.c | 10 ++++++++++ arch/powerpc/sysdev/fsl_pci.c | 4 ++-- 4 files changed, 16 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mpc5121ads.dts b/arch/powerpc/boot/dts/mpc5121ads.dts index 1f9036c317b..c2b8dbfab79 100644 --- a/arch/powerpc/boot/dts/mpc5121ads.dts +++ b/arch/powerpc/boot/dts/mpc5121ads.dts @@ -403,7 +403,8 @@ #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; - reg = <0x80008500 0x100>; + reg = <0x80008500 0x100 /* internal registers */ + 0x80008300 0x8>; /* config space access registers */ compatible = "fsl,mpc5121-pci"; device_type = "pci"; }; diff --git a/arch/powerpc/platforms/512x/Kconfig b/arch/powerpc/platforms/512x/Kconfig index c62f893ede1..326852c78b8 100644 --- a/arch/powerpc/platforms/512x/Kconfig +++ b/arch/powerpc/platforms/512x/Kconfig @@ -3,6 +3,8 @@ config PPC_MPC512x select FSL_SOC select IPIC select PPC_CLOCK + select PPC_PCI_CHOICE + select FSL_PCI if PCI config PPC_MPC5121 bool diff --git a/arch/powerpc/platforms/512x/mpc5121_ads.c b/arch/powerpc/platforms/512x/mpc5121_ads.c index 5ebf6939a69..441abc48885 100644 --- a/arch/powerpc/platforms/512x/mpc5121_ads.c +++ b/arch/powerpc/platforms/512x/mpc5121_ads.c @@ -22,16 +22,26 @@ #include #include +#include + #include "mpc512x.h" #include "mpc5121_ads.h" static void __init mpc5121_ads_setup_arch(void) { +#ifdef CONFIG_PCI + struct device_node *np; +#endif printk(KERN_INFO "MPC5121 ADS board from Freescale Semiconductor\n"); /* * cpld regs are needed early */ mpc5121_ads_cpld_map(); + +#ifdef CONFIG_PCI + for_each_compatible_node(np, "pci", "fsl,mpc5121-pci") + mpc83xx_add_bridge(np); +#endif } static void __init mpc5121_ads_init_IRQ(void) diff --git a/arch/powerpc/sysdev/fsl_pci.c b/arch/powerpc/sysdev/fsl_pci.c index a3f4abadbad..5b264eb4b1f 100644 --- a/arch/powerpc/sysdev/fsl_pci.c +++ b/arch/powerpc/sysdev/fsl_pci.c @@ -251,7 +251,7 @@ DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8641D, quirk_fsl_pcie_header); DECLARE_PCI_FIXUP_HEADER(0x1957, PCI_DEVICE_ID_MPC8610, quirk_fsl_pcie_header); #endif /* CONFIG_PPC_85xx || CONFIG_PPC_86xx */ -#if defined(CONFIG_PPC_83xx) +#if defined(CONFIG_PPC_83xx) || defined(CONFIG_PPC_MPC512x) int __init mpc83xx_add_bridge(struct device_node *dev) { int len; @@ -310,7 +310,7 @@ int __init mpc83xx_add_bridge(struct device_node *dev) setup_indirect_pci(hose, rsrc_cfg.start, rsrc_cfg.start + 4, 0); - printk(KERN_INFO "Found MPC83xx PCI host bridge at 0x%016llx. " + printk(KERN_INFO "Found FSL PCI host bridge at 0x%016llx. " "Firmware bus number: %d->%d\n", (unsigned long long)rsrc_reg.start, hose->first_busno, hose->last_busno); -- cgit v1.2.3 From 9bd54d185ab6c73f0cbd97b9f048394a3462193b Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Fri, 10 Oct 2008 06:56:52 -0500 Subject: powerpc: remove non-dependent load fsl_booke PTE_64BIT b38fd42ff46a4a31dced8533e8a6e549693500b6 added false dependencys to order the load of upper and lower halfs of the pte, but only adjusted whitespace instead of deleting the old load in the iside handler, letting the hardware see the non-dependent load. This patch removes the extra load. Signed-off-by: Milton Miller Signed-off-by: Kumar Gala --- arch/powerpc/kernel/head_fsl_booke.S | 4 ---- 1 file changed, 4 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/head_fsl_booke.S b/arch/powerpc/kernel/head_fsl_booke.S index 18c0093f932..590304c24da 100644 --- a/arch/powerpc/kernel/head_fsl_booke.S +++ b/arch/powerpc/kernel/head_fsl_booke.S @@ -656,10 +656,6 @@ interrupt_base: bne 2f /* Bail if permission mismach */ -#ifdef CONFIG_PTE_64BIT - lwz r13,0(r12) -#endif - /* Jump to common TLB load point */ b finish_tlb_load -- cgit v1.2.3 From 43c9f434922ff834a6589709714f83a78c399bc1 Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Tue, 23 Sep 2008 09:47:01 -0500 Subject: powerpc: remove support for bootmem-allocated memory for the DIU driver Early versions of the Freescale DIU framebuffer driver depended on a bootmem allocation of memory for the video buffer. The need for this feature was removed in commit 6b51d51a, so now we can remove the platform-specific code that allocated that memory. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala --- arch/powerpc/platforms/86xx/mpc8610_hpcd.c | 1 - arch/powerpc/sysdev/fsl_soc.c | 38 +----------------------------- arch/powerpc/sysdev/fsl_soc.h | 8 ------- 3 files changed, 1 insertion(+), 46 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c index 5eedb710896..e8d54ac5292 100644 --- a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c +++ b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c @@ -238,7 +238,6 @@ static void __init mpc86xx_hpcd_setup_arch(void) } #endif #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE) - preallocate_diu_videomemory(); diu_ops.get_pixel_format = mpc8610hpcd_get_pixel_format; diu_ops.set_gamma_table = mpc8610hpcd_set_gamma_table; diu_ops.set_monitor_port = mpc8610hpcd_set_monitor_port; diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c index eeb07007c75..01b884b2569 100644 --- a/arch/powerpc/sysdev/fsl_soc.c +++ b/arch/powerpc/sysdev/fsl_soc.c @@ -720,42 +720,6 @@ void fsl_rstcr_restart(char *cmd) #endif #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE) -struct platform_diu_data_ops diu_ops = { - .diu_size = 1280 * 1024 * 4, /* default one 1280x1024 buffer */ -}; +struct platform_diu_data_ops diu_ops; EXPORT_SYMBOL(diu_ops); - -int __init preallocate_diu_videomemory(void) -{ - pr_debug("diu_size=%lu\n", diu_ops.diu_size); - - diu_ops.diu_mem = __alloc_bootmem(diu_ops.diu_size, 8, 0); - if (!diu_ops.diu_mem) { - printk(KERN_ERR "fsl-diu: cannot allocate %lu bytes\n", - diu_ops.diu_size); - return -ENOMEM; - } - - pr_debug("diu_mem=%p\n", diu_ops.diu_mem); - - rh_init(&diu_ops.diu_rh_info, 4096, ARRAY_SIZE(diu_ops.diu_rh_block), - diu_ops.diu_rh_block); - return rh_attach_region(&diu_ops.diu_rh_info, - (unsigned long) diu_ops.diu_mem, - diu_ops.diu_size); -} - -static int __init early_parse_diufb(char *p) -{ - if (!p) - return 1; - - diu_ops.diu_size = _ALIGN_UP(memparse(p, &p), 8); - - pr_debug("diu_size=%lu\n", diu_ops.diu_size); - - return 0; -} -early_param("diufb", early_parse_diufb); - #endif diff --git a/arch/powerpc/sysdev/fsl_soc.h b/arch/powerpc/sysdev/fsl_soc.h index 02429988735..60f7f227327 100644 --- a/arch/powerpc/sysdev/fsl_soc.h +++ b/arch/powerpc/sysdev/fsl_soc.h @@ -20,14 +20,7 @@ extern int fsl_spi_init(struct spi_board_info *board_infos, extern void fsl_rstcr_restart(char *cmd); #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE) -#include -#include struct platform_diu_data_ops { - rh_block_t diu_rh_block[16]; - rh_info_t diu_rh_info; - unsigned long diu_size; - void *diu_mem; - unsigned int (*get_pixel_format) (unsigned int bits_per_pixel, int monitor_port); void (*set_gamma_table) (int monitor_port, char *gamma_table_base); @@ -38,7 +31,6 @@ struct platform_diu_data_ops { }; extern struct platform_diu_data_ops diu_ops; -int __init preallocate_diu_videomemory(void); #endif #endif -- cgit v1.2.3 From 8b77aeb4f52fca39e647159d87da3566f64ce30a Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 8 Oct 2008 22:16:05 +0400 Subject: powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards The RTC is sitting on the I2C1 bus at address 0x68. RTC interrupt signal is connected to the IPIC's EXT3 interrupt line. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8377_mds.dts | 7 +++++++ arch/powerpc/boot/dts/mpc8378_mds.dts | 7 +++++++ arch/powerpc/boot/dts/mpc8379_mds.dts | 7 +++++++ 3 files changed, 21 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mpc8377_mds.dts b/arch/powerpc/boot/dts/mpc8377_mds.dts index 87314c78b47..0484561bd2c 100644 --- a/arch/powerpc/boot/dts/mpc8377_mds.dts +++ b/arch/powerpc/boot/dts/mpc8377_mds.dts @@ -136,6 +136,13 @@ interrupts = <14 0x8>; interrupt-parent = <&ipic>; dfsrr; + + rtc@68 { + compatible = "dallas,ds1374"; + reg = <0x68>; + interrupts = <19 0x8>; + interrupt-parent = <&ipic>; + }; }; i2c@3100 { diff --git a/arch/powerpc/boot/dts/mpc8378_mds.dts b/arch/powerpc/boot/dts/mpc8378_mds.dts index 02941919598..67a08d2e2ff 100644 --- a/arch/powerpc/boot/dts/mpc8378_mds.dts +++ b/arch/powerpc/boot/dts/mpc8378_mds.dts @@ -136,6 +136,13 @@ interrupts = <14 0x8>; interrupt-parent = <&ipic>; dfsrr; + + rtc@68 { + compatible = "dallas,ds1374"; + reg = <0x68>; + interrupts = <19 0x8>; + interrupt-parent = <&ipic>; + }; }; i2c@3100 { diff --git a/arch/powerpc/boot/dts/mpc8379_mds.dts b/arch/powerpc/boot/dts/mpc8379_mds.dts index 13a231144dc..323370a2b5f 100644 --- a/arch/powerpc/boot/dts/mpc8379_mds.dts +++ b/arch/powerpc/boot/dts/mpc8379_mds.dts @@ -136,6 +136,13 @@ interrupts = <14 0x8>; interrupt-parent = <&ipic>; dfsrr; + + rtc@68 { + compatible = "dallas,ds1374"; + reg = <0x68>; + interrupts = <19 0x8>; + interrupt-parent = <&ipic>; + }; }; i2c@3100 { -- cgit v1.2.3 From dbe216319f4e4b23a37eeb623c8338fa59ac050e Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Fri, 10 Oct 2008 10:35:50 -0500 Subject: powerpc: disable CHRP and PMAC support in various defconfigs Because CHRP and PMAC are by default enabled, several non-CHRP and non-PMAC PowerPC defconfigs will have these Kconfig options set erroneously. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala --- arch/powerpc/configs/83xx/asp8347_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc8313_rdb_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc8315_rdb_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc832x_mds_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc832x_rdb_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc834x_itx_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc834x_mds_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc836x_mds_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc836x_rdk_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc837x_mds_defconfig | 2 ++ arch/powerpc/configs/83xx/mpc837x_rdb_defconfig | 2 ++ arch/powerpc/configs/83xx/sbc834x_defconfig | 2 ++ arch/powerpc/configs/86xx/gef_sbc610_defconfig | 5 ++++- arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig | 2 ++ arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig | 2 ++ arch/powerpc/configs/86xx/sbc8641d_defconfig | 2 ++ arch/powerpc/configs/ep8248e_defconfig | 2 ++ arch/powerpc/configs/mpc8272_ads_defconfig | 2 ++ arch/powerpc/configs/mpc83xx_defconfig | 2 ++ arch/powerpc/configs/pq2fads_defconfig | 2 ++ 21 files changed, 44 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/configs/83xx/asp8347_defconfig b/arch/powerpc/configs/83xx/asp8347_defconfig index 6638f5a03a7..0b1fa20f745 100644 --- a/arch/powerpc/configs/83xx/asp8347_defconfig +++ b/arch/powerpc/configs/83xx/asp8347_defconfig @@ -164,6 +164,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig b/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig index df125f30fae..b7eae2bdf19 100644 --- a/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig @@ -163,6 +163,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig b/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig index 6e0e08cf0b0..b0a27a67d8c 100644 --- a/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig @@ -163,6 +163,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc832x_mds_defconfig b/arch/powerpc/configs/83xx/mpc832x_mds_defconfig index d6e204a7b26..ad825bcddd1 100644 --- a/arch/powerpc/configs/83xx/mpc832x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc832x_mds_defconfig @@ -163,6 +163,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig b/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig index 1f3d3434b29..38267501f44 100644 --- a/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig @@ -163,6 +163,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc834x_itx_defconfig b/arch/powerpc/configs/83xx/mpc834x_itx_defconfig index 4686c2151d0..90aab340e7f 100644 --- a/arch/powerpc/configs/83xx/mpc834x_itx_defconfig +++ b/arch/powerpc/configs/83xx/mpc834x_itx_defconfig @@ -163,6 +163,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig b/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig index f11c25ecef7..7458a242d25 100644 --- a/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig +++ b/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig @@ -163,6 +163,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc834x_mds_defconfig b/arch/powerpc/configs/83xx/mpc834x_mds_defconfig index ffe4b2ef969..1a92798938c 100644 --- a/arch/powerpc/configs/83xx/mpc834x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc834x_mds_defconfig @@ -163,6 +163,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc836x_mds_defconfig b/arch/powerpc/configs/83xx/mpc836x_mds_defconfig index 71445e31a30..03d8cede027 100644 --- a/arch/powerpc/configs/83xx/mpc836x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc836x_mds_defconfig @@ -163,6 +163,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig b/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig index 58486ccae46..cdf84177370 100644 --- a/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig +++ b/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig @@ -164,6 +164,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc837x_mds_defconfig b/arch/powerpc/configs/83xx/mpc837x_mds_defconfig index 0171e217645..97e02d7a5b0 100644 --- a/arch/powerpc/configs/83xx/mpc837x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc837x_mds_defconfig @@ -164,6 +164,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig b/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig index d6b383bb364..5ac33054ce2 100644 --- a/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig @@ -164,6 +164,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/83xx/sbc834x_defconfig b/arch/powerpc/configs/83xx/sbc834x_defconfig index b8dd17bf040..c359cc2a380 100644 --- a/arch/powerpc/configs/83xx/sbc834x_defconfig +++ b/arch/powerpc/configs/83xx/sbc834x_defconfig @@ -162,6 +162,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/86xx/gef_sbc610_defconfig b/arch/powerpc/configs/86xx/gef_sbc610_defconfig index f589489449d..312d7afbbe4 100644 --- a/arch/powerpc/configs/86xx/gef_sbc610_defconfig +++ b/arch/powerpc/configs/86xx/gef_sbc610_defconfig @@ -156,7 +156,10 @@ CONFIG_CLASSIC_RCU=y # # Platform support # -# CONFIG_PPC_MULTIPLATFORM is not set +CONFIG_PPC_MULTIPLATFORM=y +CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set CONFIG_PPC_86xx=y diff --git a/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig b/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig index 14116a80c7c..c98c6ee4449 100644 --- a/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig +++ b/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig @@ -165,6 +165,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig b/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig index 07e369d9e48..444ddf98436 100644 --- a/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig +++ b/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig @@ -167,6 +167,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/86xx/sbc8641d_defconfig b/arch/powerpc/configs/86xx/sbc8641d_defconfig index 3326303d376..d900f8f376c 100644 --- a/arch/powerpc/configs/86xx/sbc8641d_defconfig +++ b/arch/powerpc/configs/86xx/sbc8641d_defconfig @@ -166,6 +166,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/ep8248e_defconfig b/arch/powerpc/configs/ep8248e_defconfig index a63cd05ef20..cd691f77081 100644 --- a/arch/powerpc/configs/ep8248e_defconfig +++ b/arch/powerpc/configs/ep8248e_defconfig @@ -150,6 +150,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/mpc8272_ads_defconfig b/arch/powerpc/configs/mpc8272_ads_defconfig index ddbca3e39ba..ff6f7c475f4 100644 --- a/arch/powerpc/configs/mpc8272_ads_defconfig +++ b/arch/powerpc/configs/mpc8272_ads_defconfig @@ -151,6 +151,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/mpc83xx_defconfig b/arch/powerpc/configs/mpc83xx_defconfig index 994a4e7257f..991c9bda12a 100644 --- a/arch/powerpc/configs/mpc83xx_defconfig +++ b/arch/powerpc/configs/mpc83xx_defconfig @@ -166,6 +166,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set diff --git a/arch/powerpc/configs/pq2fads_defconfig b/arch/powerpc/configs/pq2fads_defconfig index e687cc0f2a9..7e17862c38b 100644 --- a/arch/powerpc/configs/pq2fads_defconfig +++ b/arch/powerpc/configs/pq2fads_defconfig @@ -152,6 +152,8 @@ CONFIG_CLASSIC_RCU=y # CONFIG_PPC_MULTIPLATFORM=y CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set +# CONFIG_PPC_PMAC is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set # CONFIG_PPC_MPC52xx is not set -- cgit v1.2.3 From 7de0c22bba1f6117c3447af2cdca9904303012da Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Fri, 10 Oct 2008 11:52:32 -0500 Subject: powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree The Freescale Elo DMA driver binds to all DMA channels in the device tree that are compatible with "fsl,eloplus-dma-channel". This conflicts with the sound drivers for the MPC8610 HPCD. On this board, the SSI uses two DMA channels and therefore those channels are not available for general purpose use. We change the compatible properties for these channels "fsl,ssi-dma-channel". This works because the sound drivers don't actually check the compatible property when it grabs channels. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8610_hpcd.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mpc8610_hpcd.dts b/arch/powerpc/boot/dts/mpc8610_hpcd.dts index 0f3a36e0ea6..3f4c6102e4e 100644 --- a/arch/powerpc/boot/dts/mpc8610_hpcd.dts +++ b/arch/powerpc/boot/dts/mpc8610_hpcd.dts @@ -237,7 +237,7 @@ dma00: dma-channel@0 { compatible = "fsl,mpc8610-dma-channel", - "fsl,eloplus-dma-channel"; + "fsl,ssi-dma-channel"; cell-index = <0>; reg = <0x0 0x80>; interrupt-parent = <&mpic>; @@ -245,7 +245,7 @@ }; dma01: dma-channel@1 { compatible = "fsl,mpc8610-dma-channel", - "fsl,eloplus-dma-channel"; + "fsl,ssi-dma-channel"; cell-index = <1>; reg = <0x80 0x80>; interrupt-parent = <&mpic>; -- cgit v1.2.3 From 6675847ea42d5acfaa644ac24eb0d87df5769cd5 Mon Sep 17 00:00:00 2001 From: Martyn Welch Date: Mon, 13 Oct 2008 16:16:45 +0100 Subject: powerpc: FPGA support for GE Fanuc SBC610 Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D). This patch adds support for the registers held in the devices main FPGA, exposing extra information about the revision of the board through cpuinfo. Signed-off-by: Martyn Welch Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/gef_sbc610.dts | 4 ++++ arch/powerpc/platforms/86xx/gef_sbc610.c | 40 ++++++++++++++++++++++++++++++++ 2 files changed, 44 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/gef_sbc610.dts b/arch/powerpc/boot/dts/gef_sbc610.dts index 771a776d610..6ed608322dd 100644 --- a/arch/powerpc/boot/dts/gef_sbc610.dts +++ b/arch/powerpc/boot/dts/gef_sbc610.dts @@ -84,6 +84,10 @@ 6 0 0xfd000000 0x00800000 // IO FPGA (8-bit) 7 0 0xfd800000 0x00800000>; // IO FPGA (32-bit) + fpga@4,0 { + compatible = "gef,fpga-regs"; + reg = <0x4 0x0 0x40>; + }; gef_pic: pic@4,4000 { #interrupt-cells = <1>; interrupt-controller; diff --git a/arch/powerpc/platforms/86xx/gef_sbc610.c b/arch/powerpc/platforms/86xx/gef_sbc610.c index 3873c2018cc..821c45fac18 100644 --- a/arch/powerpc/platforms/86xx/gef_sbc610.c +++ b/arch/powerpc/platforms/86xx/gef_sbc610.c @@ -73,6 +73,7 @@ static void __init gef_sbc610_init_irq(void) static void __init gef_sbc610_setup_arch(void) { + struct device_node *regs; #ifdef CONFIG_PCI struct device_node *np; @@ -86,8 +87,43 @@ static void __init gef_sbc610_setup_arch(void) #ifdef CONFIG_SMP mpc86xx_smp_init(); #endif + + /* Remap basic board registers */ + regs = of_find_compatible_node(NULL, NULL, "gef,fpga-regs"); + if (regs) { + sbc610_regs = of_iomap(regs, 0); + if (sbc610_regs == NULL) + printk(KERN_WARNING "Unable to map board registers\n"); + of_node_put(regs); + } +} + +/* Return the PCB revision */ +static unsigned int gef_sbc610_get_pcb_rev(void) +{ + unsigned int reg; + + reg = ioread32(sbc610_regs); + return (reg >> 8) & 0xff; +} + +/* Return the board (software) revision */ +static unsigned int gef_sbc610_get_board_rev(void) +{ + unsigned int reg; + + reg = ioread32(sbc610_regs); + return (reg >> 16) & 0xff; } +/* Return the FPGA revision */ +static unsigned int gef_sbc610_get_fpga_rev(void) +{ + unsigned int reg; + + reg = ioread32(sbc610_regs); + return (reg >> 24) & 0xf; +} static void gef_sbc610_show_cpuinfo(struct seq_file *m) { @@ -96,6 +132,10 @@ static void gef_sbc610_show_cpuinfo(struct seq_file *m) seq_printf(m, "Vendor\t\t: GE Fanuc Intelligent Platforms\n"); + seq_printf(m, "Revision\t: %u%c\n", gef_sbc610_get_pcb_rev(), + ('A' + gef_sbc610_get_board_rev() - 1)); + seq_printf(m, "FPGA Revision\t: %u\n", gef_sbc610_get_fpga_rev()); + seq_printf(m, "SVR\t\t: 0x%x\n", svid); seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024)); } -- cgit v1.2.3 From 1fb25be1e74498d389e4de819a6d1b174d6ccb7c Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Fri, 10 Oct 2008 22:05:12 +0400 Subject: powerpc/83xx: add NAND support for the MPC8360E-RDK boards The StMicro NAND chip (512Mbit, 64MB) is connected to the local bus, the first local bus' user-programmable machine is configured by the firmware to work with NAND chips. QE GPIO pin is used to poll the NAND's Ready-Not-Busy signal. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc836x_rdk.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mpc836x_rdk.dts b/arch/powerpc/boot/dts/mpc836x_rdk.dts index f747747e531..decadf3d9e9 100644 --- a/arch/powerpc/boot/dts/mpc836x_rdk.dts +++ b/arch/powerpc/boot/dts/mpc836x_rdk.dts @@ -387,6 +387,18 @@ device-width = <1>; }; + upm@1,0 { + compatible = "fsl,upm-nand"; + reg = <1 0 1>; + fsl,upm-addr-offset = <16>; + fsl,upm-cmd-offset = <8>; + gpios = <&qe_pio_e 18 0>; + + flash { + compatible = "stm,nand512-a"; + }; + }; + display@2,0 { device_type = "display"; compatible = "fujitsu,MB86277", "fujitsu,mint"; -- cgit v1.2.3 From c0da99d5f7b0349cb11f970b3283c0d57beb5ec9 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 9 Oct 2008 04:32:59 +0400 Subject: powerpc: fix fsl_upm nand driver modular build The fsl_upm nand driver fails to build because fsl_lbc_lock isn't exported, the lock is needed by the inlined fsl_upm_run_pattern() function: ERROR: "fsl_lbc_lock" [drivers/mtd/nand/fsl_upm.ko] undefined! Dave Jones purposed to export the lock, but it is better to just uninline the fsl_upm_run_pattern(). When uninlined we also no longer need the exported fsl_lbc_regs, and both fsl_lbc_lock and fsl_lbc_regs could be marked static. While at it, also add some missing includes that we should have included explicitly. Reported-by: Dave Jones Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/include/asm/fsl_lbc.h | 48 +++------------------------------- arch/powerpc/sysdev/fsl_lbc.c | 53 +++++++++++++++++++++++++++++++++++--- 2 files changed, 53 insertions(+), 48 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/fsl_lbc.h b/arch/powerpc/include/asm/fsl_lbc.h index 303f5484c05..63a4f779f53 100644 --- a/arch/powerpc/include/asm/fsl_lbc.h +++ b/arch/powerpc/include/asm/fsl_lbc.h @@ -23,9 +23,9 @@ #ifndef __ASM_FSL_LBC_H #define __ASM_FSL_LBC_H +#include #include -#include -#include +#include struct fsl_lbc_bank { __be32 br; /**< Base Register */ @@ -227,9 +227,6 @@ struct fsl_lbc_regs { u8 res8[0xF00]; }; -extern struct fsl_lbc_regs __iomem *fsl_lbc_regs; -extern spinlock_t fsl_lbc_lock; - /* * FSL UPM routines */ @@ -268,44 +265,7 @@ static inline void fsl_upm_end_pattern(struct fsl_upm *upm) cpu_relax(); } -/** - * fsl_upm_run_pattern - actually run an UPM pattern - * @upm: pointer to the fsl_upm structure obtained via fsl_upm_find - * @io_base: remapped pointer to where memory access should happen - * @mar: MAR register content during pattern execution - * - * This function triggers dummy write to the memory specified by the io_base, - * thus UPM pattern actually executed. Note that mar usage depends on the - * pre-programmed AMX bits in the UPM RAM. - */ -static inline int fsl_upm_run_pattern(struct fsl_upm *upm, - void __iomem *io_base, u32 mar) -{ - int ret = 0; - unsigned long flags; - - spin_lock_irqsave(&fsl_lbc_lock, flags); - - out_be32(&fsl_lbc_regs->mar, mar << (32 - upm->width)); - - switch (upm->width) { - case 8: - out_8(io_base, 0x0); - break; - case 16: - out_be16(io_base, 0x0); - break; - case 32: - out_be32(io_base, 0x0); - break; - default: - ret = -EINVAL; - break; - } - - spin_unlock_irqrestore(&fsl_lbc_lock, flags); - - return ret; -} +extern int fsl_upm_run_pattern(struct fsl_upm *upm, void __iomem *io_base, + u32 mar); #endif /* __ASM_FSL_LBC_H */ diff --git a/arch/powerpc/sysdev/fsl_lbc.c b/arch/powerpc/sysdev/fsl_lbc.c index 422c8faef59..0494ee55920 100644 --- a/arch/powerpc/sysdev/fsl_lbc.c +++ b/arch/powerpc/sysdev/fsl_lbc.c @@ -11,14 +11,19 @@ * (at your option) any later version. */ +#include +#include #include +#include +#include +#include +#include #include +#include #include -spinlock_t fsl_lbc_lock = __SPIN_LOCK_UNLOCKED(fsl_lbc_lock); - -struct fsl_lbc_regs __iomem *fsl_lbc_regs; -EXPORT_SYMBOL(fsl_lbc_regs); +static spinlock_t fsl_lbc_lock = __SPIN_LOCK_UNLOCKED(fsl_lbc_lock); +static struct fsl_lbc_regs __iomem *fsl_lbc_regs; static char __initdata *compat_lbc[] = { "fsl,pq2-localbus", @@ -127,3 +132,43 @@ int fsl_upm_find(phys_addr_t addr_base, struct fsl_upm *upm) return 0; } EXPORT_SYMBOL(fsl_upm_find); + +/** + * fsl_upm_run_pattern - actually run an UPM pattern + * @upm: pointer to the fsl_upm structure obtained via fsl_upm_find + * @io_base: remapped pointer to where memory access should happen + * @mar: MAR register content during pattern execution + * + * This function triggers dummy write to the memory specified by the io_base, + * thus UPM pattern actually executed. Note that mar usage depends on the + * pre-programmed AMX bits in the UPM RAM. + */ +int fsl_upm_run_pattern(struct fsl_upm *upm, void __iomem *io_base, u32 mar) +{ + int ret = 0; + unsigned long flags; + + spin_lock_irqsave(&fsl_lbc_lock, flags); + + out_be32(&fsl_lbc_regs->mar, mar << (32 - upm->width)); + + switch (upm->width) { + case 8: + out_8(io_base, 0x0); + break; + case 16: + out_be16(io_base, 0x0); + break; + case 32: + out_be32(io_base, 0x0); + break; + default: + ret = -EINVAL; + break; + } + + spin_unlock_irqrestore(&fsl_lbc_lock, flags); + + return ret; +} +EXPORT_SYMBOL(fsl_upm_run_pattern); -- cgit v1.2.3 From 8aa2659009714cf5f9ffe7f3e16ccfa8ff0e0d61 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Thu, 9 Oct 2008 17:06:24 +0000 Subject: powerpc: Fix DMA offset for non-coherent DMA After Becky's work we can almost have different DMA offsets between on-chip devices and PCI. Almost because there's a problem with the non-coherent DMA code that basically ignores the programmed offset to use the global one for everything. This fixes it. Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/dma.c | 8 ++++++-- arch/powerpc/lib/dma-noncoherent.c | 2 +- 2 files changed, 7 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/dma.c b/arch/powerpc/kernel/dma.c index 41fdd48bf43..1562daf8839 100644 --- a/arch/powerpc/kernel/dma.c +++ b/arch/powerpc/kernel/dma.c @@ -30,11 +30,15 @@ static unsigned long get_dma_direct_offset(struct device *dev) void *dma_direct_alloc_coherent(struct device *dev, size_t size, dma_addr_t *dma_handle, gfp_t flag) { + void *ret; #ifdef CONFIG_NOT_COHERENT_CACHE - return __dma_alloc_coherent(size, dma_handle, flag); + ret = __dma_alloc_coherent(size, dma_handle, flag); + if (ret == NULL) + return NULL; + *dma_handle += get_dma_direct_offset(dev); + return ret; #else struct page *page; - void *ret; int node = dev_to_node(dev); /* ignore region specifiers */ diff --git a/arch/powerpc/lib/dma-noncoherent.c b/arch/powerpc/lib/dma-noncoherent.c index 5d83907f659..31734c0969c 100644 --- a/arch/powerpc/lib/dma-noncoherent.c +++ b/arch/powerpc/lib/dma-noncoherent.c @@ -203,7 +203,7 @@ __dma_alloc_coherent(size_t size, dma_addr_t *handle, gfp_t gfp) /* * Set the "dma handle" */ - *handle = page_to_bus(page); + *handle = page_to_phys(page); do { BUG_ON(!pte_none(*pte)); -- cgit v1.2.3 From cd301c7ba4bbb5a0ee6ebf13eb4a304f29b13847 Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Sun, 12 Oct 2008 04:08:14 +0000 Subject: powerpc: Reflect the used arguments in machine_init() prototype The "phys" argument to machine_init() isn't used and isn't likely to ever be so let's remove it. Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/setup_32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/setup_32.c b/arch/powerpc/kernel/setup_32.c index 1e0df1658d3..c1a27626a94 100644 --- a/arch/powerpc/kernel/setup_32.c +++ b/arch/powerpc/kernel/setup_32.c @@ -111,7 +111,7 @@ notrace unsigned long __init early_init(unsigned long dt_ptr) * This is called very early on the boot process, after a minimal * MMU environment has been set up but before MMU_init is called. */ -notrace void __init machine_init(unsigned long dt_ptr, unsigned long phys) +notrace void __init machine_init(unsigned long dt_ptr) { /* Enable early debugging if any specified (see udbg.h) */ udbg_early_init(); -- cgit v1.2.3 From f5ea64dcbad89875d130596df14c9b25d994a737 Mon Sep 17 00:00:00 2001 From: David Gibson Date: Sun, 12 Oct 2008 17:54:24 +0000 Subject: powerpc: Get USE_STRICT_MM_TYPECHECKS working again The typesafe version of the powerpc pagetable handling (with USE_STRICT_MM_TYPECHECKS defined) has bitrotted again. This patch makes a bunch of small fixes to get it back to building status. It's still not enabled by default as gcc still generates worse code with it for some reason. Signed-off-by: David Gibson Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/include/asm/mman.h | 2 +- arch/powerpc/include/asm/pgtable-ppc32.h | 17 +++++++++-------- arch/powerpc/include/asm/pgtable-ppc64.h | 12 ++++++------ arch/powerpc/mm/gup.c | 7 ++++--- arch/powerpc/mm/hash_utils_64.c | 4 ++-- arch/powerpc/mm/init_64.c | 4 ++-- 6 files changed, 24 insertions(+), 22 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/mman.h b/arch/powerpc/include/asm/mman.h index 9209f755763..e7b99bac9f4 100644 --- a/arch/powerpc/include/asm/mman.h +++ b/arch/powerpc/include/asm/mman.h @@ -44,7 +44,7 @@ static inline unsigned long arch_calc_vm_prot_bits(unsigned long prot) static inline pgprot_t arch_vm_get_page_prot(unsigned long vm_flags) { - return (vm_flags & VM_SAO) ? __pgprot(_PAGE_SAO) : 0; + return (vm_flags & VM_SAO) ? __pgprot(_PAGE_SAO) : __pgprot(0); } #define arch_vm_get_page_prot(vm_flags) arch_vm_get_page_prot(vm_flags) diff --git a/arch/powerpc/include/asm/pgtable-ppc32.h b/arch/powerpc/include/asm/pgtable-ppc32.h index 29c83d85b04..6ab7c67cb5a 100644 --- a/arch/powerpc/include/asm/pgtable-ppc32.h +++ b/arch/powerpc/include/asm/pgtable-ppc32.h @@ -431,11 +431,11 @@ extern int icache_44x_need_flush; #define _PAGE_CHG_MASK (PAGE_MASK | _PAGE_ACCESSED | _PAGE_DIRTY) -#define PAGE_PROT_BITS __pgprot(_PAGE_GUARDED | _PAGE_COHERENT | _PAGE_NO_CACHE | \ - _PAGE_WRITETHRU | _PAGE_ENDIAN | \ - _PAGE_USER | _PAGE_ACCESSED | \ - _PAGE_RW | _PAGE_HWWRITE | _PAGE_DIRTY | \ - _PAGE_EXEC | _PAGE_HWEXEC) +#define PAGE_PROT_BITS (_PAGE_GUARDED | _PAGE_COHERENT | _PAGE_NO_CACHE | \ + _PAGE_WRITETHRU | _PAGE_ENDIAN | \ + _PAGE_USER | _PAGE_ACCESSED | \ + _PAGE_RW | _PAGE_HWWRITE | _PAGE_DIRTY | \ + _PAGE_EXEC | _PAGE_HWEXEC) /* * Note: the _PAGE_COHERENT bit automatically gets set in the hardware * PTE if CONFIG_SMP is defined (hash_page does this); there is no need @@ -570,9 +570,9 @@ static inline pte_t pte_mkyoung(pte_t pte) { pte_val(pte) |= _PAGE_ACCESSED; return pte; } static inline pte_t pte_mkspecial(pte_t pte) { pte_val(pte) |= _PAGE_SPECIAL; return pte; } -static inline unsigned long pte_pgprot(pte_t pte) +static inline pgprot_t pte_pgprot(pte_t pte) { - return __pgprot(pte_val(pte)) & PAGE_PROT_BITS; + return __pgprot(pte_val(pte) & PAGE_PROT_BITS); } static inline pte_t pte_modify(pte_t pte, pgprot_t newprot) @@ -688,7 +688,8 @@ static inline void __set_pte_at(struct mm_struct *mm, unsigned long addr, : "=m" (*ptep), "=m" (*((unsigned char *)ptep+4)) : "r" (pte) : "memory"); #else - *ptep = (*ptep & _PAGE_HASHPTE) | (pte & ~_PAGE_HASHPTE); + *ptep = __pte((pte_val(*ptep) & _PAGE_HASHPTE) + | (pte_val(pte) & ~_PAGE_HASHPTE)); #endif } diff --git a/arch/powerpc/include/asm/pgtable-ppc64.h b/arch/powerpc/include/asm/pgtable-ppc64.h index 4597c491e9b..4c0a8c62859 100644 --- a/arch/powerpc/include/asm/pgtable-ppc64.h +++ b/arch/powerpc/include/asm/pgtable-ppc64.h @@ -117,10 +117,10 @@ #define PAGE_AGP __pgprot(_PAGE_BASE | _PAGE_WRENABLE | _PAGE_NO_CACHE) #define HAVE_PAGE_AGP -#define PAGE_PROT_BITS __pgprot(_PAGE_GUARDED | _PAGE_COHERENT | \ - _PAGE_NO_CACHE | _PAGE_WRITETHRU | \ - _PAGE_4K_PFN | _PAGE_RW | _PAGE_USER | \ - _PAGE_ACCESSED | _PAGE_DIRTY | _PAGE_EXEC) +#define PAGE_PROT_BITS (_PAGE_GUARDED | _PAGE_COHERENT | \ + _PAGE_NO_CACHE | _PAGE_WRITETHRU | \ + _PAGE_4K_PFN | _PAGE_RW | _PAGE_USER | \ + _PAGE_ACCESSED | _PAGE_DIRTY | _PAGE_EXEC) /* PTEIDX nibble */ #define _PTEIDX_SECONDARY 0x8 #define _PTEIDX_GROUP_IX 0x7 @@ -264,9 +264,9 @@ static inline pte_t pte_mkhuge(pte_t pte) { return pte; } static inline pte_t pte_mkspecial(pte_t pte) { pte_val(pte) |= _PAGE_SPECIAL; return pte; } -static inline unsigned long pte_pgprot(pte_t pte) +static inline pgprot_t pte_pgprot(pte_t pte) { - return __pgprot(pte_val(pte)) & PAGE_PROT_BITS; + return __pgprot(pte_val(pte) & PAGE_PROT_BITS); } /* Atomic PTE updates */ diff --git a/arch/powerpc/mm/gup.c b/arch/powerpc/mm/gup.c index 9fdf4d6335e..28a114db3ba 100644 --- a/arch/powerpc/mm/gup.c +++ b/arch/powerpc/mm/gup.c @@ -41,7 +41,7 @@ static noinline int gup_pte_range(pmd_t pmd, unsigned long addr, page = pte_page(pte); if (!page_cache_get_speculative(page)) return 0; - if (unlikely(pte != *ptep)) { + if (unlikely(pte_val(pte) != pte_val(*ptep))) { put_page(page); return 0; } @@ -92,7 +92,7 @@ static noinline int gup_huge_pte(pte_t *ptep, struct hstate *hstate, *nr -= refs; return 0; } - if (unlikely(pte != *ptep)) { + if (unlikely(pte_val(pte) != pte_val(*ptep))) { /* Could be optimized better */ while (*nr) { put_page(page); @@ -237,7 +237,8 @@ int get_user_pages_fast(unsigned long start, int nr_pages, int write, pgd_t pgd = *pgdp; VM_BUG_ON(shift != mmu_psize_defs[get_slice_psize(mm, addr)].shift); - pr_debug(" %016lx: normal pgd %p\n", addr, (void *)pgd); + pr_debug(" %016lx: normal pgd %p\n", addr, + (void *)pgd_val(pgd)); next = pgd_addr_end(addr, end); if (pgd_none(pgd)) goto slow; diff --git a/arch/powerpc/mm/hash_utils_64.c b/arch/powerpc/mm/hash_utils_64.c index 09db4efe192..5c64af17475 100644 --- a/arch/powerpc/mm/hash_utils_64.c +++ b/arch/powerpc/mm/hash_utils_64.c @@ -541,7 +541,7 @@ static unsigned long __init htab_get_table_size(void) void create_section_mapping(unsigned long start, unsigned long end) { BUG_ON(htab_bolt_mapping(start, end, __pa(start), - PAGE_KERNEL, mmu_linear_psize, + pgprot_val(PAGE_KERNEL), mmu_linear_psize, mmu_kernel_ssize)); } @@ -649,7 +649,7 @@ void __init htab_initialize(void) mtspr(SPRN_SDR1, _SDR1); } - prot = PAGE_KERNEL; + prot = pgprot_val(PAGE_KERNEL); #ifdef CONFIG_DEBUG_PAGEALLOC linear_map_hash_count = lmb_end_of_DRAM() >> PAGE_SHIFT; diff --git a/arch/powerpc/mm/init_64.c b/arch/powerpc/mm/init_64.c index 036fe2f10c7..3e6a6543f53 100644 --- a/arch/powerpc/mm/init_64.c +++ b/arch/powerpc/mm/init_64.c @@ -228,8 +228,8 @@ int __meminit vmemmap_populate(struct page *start_page, start, p, __pa(p)); mapped = htab_bolt_mapping(start, start + page_size, __pa(p), - PAGE_KERNEL, mmu_vmemmap_psize, - mmu_kernel_ssize); + pgprot_val(PAGE_KERNEL), + mmu_vmemmap_psize, mmu_kernel_ssize); BUG_ON(mapped < 0); } -- cgit v1.2.3 From b556151110ff003ce77d84597400c84824690ccf Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Mon, 13 Oct 2008 13:56:31 +0000 Subject: powerpc/pci: Improve detection of unassigned bridge resources When the powerpc PCI layer is not configured to re-assign everything, it currently fails to detect that a PCI to PCI bridge has been left unassigned by the firmware and tries to allocate resource for the default window values in the bridge (0...X) (with the notable exception of a hack we have in there that detects some Apple firmware unassigned bridge resources). This results in resource allocation failures, which are generally fixed up later on but it causes scary warnings in the logs and we have seen the fixup code fall over in some circumstances (a different issue to fix as well). This code improves that by providing a more complete & useful function to intuit that a bridge was left unassigned by the firmware, and thus force a full re-allocation by the PCI code without trying to allocate the existing useless resources first. The algorithm we use basically considers unassigned a window that starts at 0 (PCI address) if the corresponding address space enable bit is not set. In addition, for memory space, it considers such a resource unassigned also if the host bridge isn't configured to forward cycles to address 0 (ie, the resource basically overlaps main memory). This fixes a range of problems with things like Bare-Metal support on pSeries machines, or attempt to use partial firmware PCI setup. Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/pci-common.c | 163 ++++++++++++++++++++++++++++----------- 1 file changed, 116 insertions(+), 47 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/pci-common.c b/arch/powerpc/kernel/pci-common.c index 8c0270929cc..01ce8c38bae 100644 --- a/arch/powerpc/kernel/pci-common.c +++ b/arch/powerpc/kernel/pci-common.c @@ -780,11 +780,6 @@ static void __devinit fixup_resource(struct resource *res, struct pci_dev *dev) res->start = (res->start + offset) & mask; res->end = (res->end + offset) & mask; - - pr_debug("PCI:%s %016llx-%016llx\n", - pci_name(dev), - (unsigned long long)res->start, - (unsigned long long)res->end); } @@ -830,6 +825,11 @@ static void __devinit pcibios_fixup_resources(struct pci_dev *dev) (unsigned int)res->flags); fixup_resource(res, dev); + + pr_debug("PCI:%s %016llx-%016llx\n", + pci_name(dev), + (unsigned long long)res->start, + (unsigned long long)res->end); } /* Call machine specific resource fixup */ @@ -838,58 +838,127 @@ static void __devinit pcibios_fixup_resources(struct pci_dev *dev) } DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, pcibios_fixup_resources); -static void __devinit __pcibios_fixup_bus(struct pci_bus *bus) +/* This function tries to figure out if a bridge resource has been initialized + * by the firmware or not. It doesn't have to be absolutely bullet proof, but + * things go more smoothly when it gets it right. It should covers cases such + * as Apple "closed" bridge resources and bare-metal pSeries unassigned bridges + */ +static int __devinit pcibios_uninitialized_bridge_resource(struct pci_bus *bus, + struct resource *res) { struct pci_controller *hose = pci_bus_to_host(bus); struct pci_dev *dev = bus->self; + resource_size_t offset; + u16 command; + int i; - pr_debug("PCI: Fixup bus %d (%s)\n", bus->number, dev ? pci_name(dev) : "PHB"); + /* We don't do anything if PCI_PROBE_ONLY is set */ + if (ppc_pci_flags & PPC_PCI_PROBE_ONLY) + return 0; - /* Fixup PCI<->PCI bridges. Host bridges are handled separately, for - * now differently between 32 and 64 bits. - */ - if (dev != NULL) { - struct resource *res; - int i; + /* Job is a bit different between memory and IO */ + if (res->flags & IORESOURCE_MEM) { + /* If the BAR is non-0 (res != pci_mem_offset) then it's probably been + * initialized by somebody + */ + if (res->start != hose->pci_mem_offset) + return 0; - for (i = 0; i < PCI_BUS_NUM_RESOURCES; ++i) { - if ((res = bus->resource[i]) == NULL) - continue; - if (!res->flags) - continue; - if (i >= 3 && bus->self->transparent) - continue; - /* On PowerMac, Apple leaves bridge windows open over - * an inaccessible region of memory space (0...fffff) - * which is somewhat bogus, but that's what they think - * means disabled... - * - * We clear those to force them to be reallocated later - * - * We detect such regions by the fact that the base is - * equal to the pci_mem_offset of the host bridge and - * their size is smaller than 1M. - */ - if (res->flags & IORESOURCE_MEM && - res->start == hose->pci_mem_offset && - res->end < 0x100000) { - printk(KERN_INFO - "PCI: Closing bogus Apple Firmware" - " region %d on bus 0x%02x\n", - i, bus->number); - res->flags = 0; - continue; - } + /* The BAR is 0, let's check if memory decoding is enabled on + * the bridge. If not, we consider it unassigned + */ + pci_read_config_word(dev, PCI_COMMAND, &command); + if ((command & PCI_COMMAND_MEMORY) == 0) + return 1; - pr_debug("PCI:%s Bus rsrc %d %016llx-%016llx [%x] fixup...\n", - pci_name(dev), i, - (unsigned long long)res->start,\ - (unsigned long long)res->end, - (unsigned int)res->flags); + /* Memory decoding is enabled and the BAR is 0. If any of the bridge + * resources covers that starting address (0 then it's good enough for + * us for memory + */ + for (i = 0; i < 3; i++) { + if ((hose->mem_resources[i].flags & IORESOURCE_MEM) && + hose->mem_resources[i].start == hose->pci_mem_offset) + return 0; + } + + /* Well, it starts at 0 and we know it will collide so we may as + * well consider it as unassigned. That covers the Apple case. + */ + return 1; + } else { + /* If the BAR is non-0, then we consider it assigned */ + offset = (unsigned long)hose->io_base_virt - _IO_BASE; + if (((res->start - offset) & 0xfffffffful) != 0) + return 0; + + /* Here, we are a bit different than memory as typically IO space + * starting at low addresses -is- valid. What we do instead if that + * we consider as unassigned anything that doesn't have IO enabled + * in the PCI command register, and that's it. + */ + pci_read_config_word(dev, PCI_COMMAND, &command); + if (command & PCI_COMMAND_IO) + return 0; + + /* It's starting at 0 and IO is disabled in the bridge, consider + * it unassigned + */ + return 1; + } +} + +/* Fixup resources of a PCI<->PCI bridge */ +static void __devinit pcibios_fixup_bridge(struct pci_bus *bus) +{ + struct resource *res; + int i; + + struct pci_dev *dev = bus->self; - fixup_resource(res, dev); + for (i = 0; i < PCI_BUS_NUM_RESOURCES; ++i) { + if ((res = bus->resource[i]) == NULL) + continue; + if (!res->flags) + continue; + if (i >= 3 && bus->self->transparent) + continue; + + pr_debug("PCI:%s Bus rsrc %d %016llx-%016llx [%x] fixup...\n", + pci_name(dev), i, + (unsigned long long)res->start,\ + (unsigned long long)res->end, + (unsigned int)res->flags); + + /* Perform fixup */ + fixup_resource(res, dev); + + /* Try to detect uninitialized P2P bridge resources, + * and clear them out so they get re-assigned later + */ + if (pcibios_uninitialized_bridge_resource(bus, res)) { + res->flags = 0; + pr_debug("PCI:%s (unassigned)\n", pci_name(dev)); + } else { + + pr_debug("PCI:%s %016llx-%016llx\n", + pci_name(dev), + (unsigned long long)res->start, + (unsigned long long)res->end); } } +} + +static void __devinit __pcibios_fixup_bus(struct pci_bus *bus) +{ + struct pci_dev *dev = bus->self; + + pr_debug("PCI: Fixup bus %d (%s)\n", bus->number, dev ? pci_name(dev) : "PHB"); + + /* Fixup PCI<->PCI bridges. Host bridges are handled separately, for + * now differently between 32 and 64 bits. + */ + if (dev != NULL) + pcibios_fixup_bridge(bus); /* Additional setup that is different between 32 and 64 bits for now */ pcibios_do_bus_setup(bus); -- cgit v1.2.3 From 7b6b574ca7d5d5ba6ae7155c1fb877cc7130eff7 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Mon, 13 Oct 2008 17:51:46 +0000 Subject: powerpc: Fix link errors on 32-bit machines using legacy DMA The new merged DMA code will try to access isa_bridge_pcidev when trying to DMA to/from legacy devices. This is however only defined on 64-bit. Fixes this for now by adding the variable, even if it stays NULL. In the long run, we'll make isa-bridge.c common to 32 and 64-bit. Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/pci_32.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/kernel/pci_32.c b/arch/powerpc/kernel/pci_32.c index a848c6360bd..131b1dfa68c 100644 --- a/arch/powerpc/kernel/pci_32.c +++ b/arch/powerpc/kernel/pci_32.c @@ -53,6 +53,12 @@ LIST_HEAD(hose_list); static int pci_bus_count; +/* This will remain NULL for now, until isa-bridge.c is made common + * to both 32-bit and 64-bit. + */ +struct pci_dev *isa_bridge_pcidev; +EXPORT_SYMBOL_GPL(isa_bridge_pcidev); + static void fixup_hide_host_resource_fsl(struct pci_dev *dev) { -- cgit v1.2.3 From 2bda347bc53fe2cacd5621d8a0426840a8d2a6a6 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Mon, 13 Oct 2008 18:38:48 +0000 Subject: powerpc: Fix 32-bit SMP boot on CHRP prom_init was changed to take a new argument, the address where the kernel is loaded, which is now used to copy the SMP spin loop down before use. However, only head_64.S was adapted to pass this new value, not head_32.S, thus breaking SMP boot on 32-bit SMP CHRP machines. Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/head_32.S | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/kernel/head_32.S b/arch/powerpc/kernel/head_32.S index a6de6dbc5ed..0c326823c6d 100644 --- a/arch/powerpc/kernel/head_32.S +++ b/arch/powerpc/kernel/head_32.S @@ -110,6 +110,12 @@ __start: #ifdef CONFIG_PPC_MULTIPLATFORM cmpwi 0,r5,0 beq 1f + + /* find out where we are now */ + bcl 20,31,$+4 +0: mflr r8 /* r8 = runtime addr here */ + addis r8,r8,(_stext - 0b)@ha + addi r8,r8,(_stext - 0b)@l /* current runtime base addr */ bl prom_init trap #endif -- cgit v1.2.3 From 22007a165d2da38686d528f3af5c5d8b6713728c Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Mon, 13 Oct 2008 20:14:09 +0000 Subject: powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs The detection of the IBM "Python" PCI host bridge on IBM CHRP machines such as old RS6000 was broken when we changed of_device_is_compatible() from strncasecmp to strcasecmp (dropped the "n" variant) due to the way IBM encodes the chip version. We fix that by instead doing a match on the model property like we do for others bridges in that file. It should be good enough for those machines. If yours is still broken, let me know. Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/chrp/pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/chrp/pci.c b/arch/powerpc/platforms/chrp/pci.c index 768c262b936..68e49b24df9 100644 --- a/arch/powerpc/platforms/chrp/pci.c +++ b/arch/powerpc/platforms/chrp/pci.c @@ -266,7 +266,7 @@ chrp_find_bridges(void) model = of_get_property(dev, "model", NULL); if (model == NULL) model = ""; - if (of_device_is_compatible(dev, "IBM,python")) { + if (strncmp(model, "IBM, Python", 11) == 0) { setup_python(hose, dev); } else if (is_mot || strncmp(model, "Motorola, Grackle", 17) == 0) { -- cgit v1.2.3 From ee673eaa72d8d185012b1027a05e25aba18c267f Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Mon, 13 Oct 2008 20:49:47 +0000 Subject: powerpc: Fix CHRP PCI config access for indirect_pci Recently, indirect_pci was changed to test if the bus number requested is the one hanging straight off the PHB, then it substitutes the bus number with another one contained in a new "self_busno" field of the pci_controller structure. However, this breaks CHRP which didn't initialize this new field, and which relies on having the right bus number passed to the hardware. This fixes it by initializing this variable properly for all CHRP bridges Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/chrp/pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/chrp/pci.c b/arch/powerpc/platforms/chrp/pci.c index 68e49b24df9..d3cde6b9d2d 100644 --- a/arch/powerpc/platforms/chrp/pci.c +++ b/arch/powerpc/platforms/chrp/pci.c @@ -260,7 +260,7 @@ chrp_find_bridges(void) dev->full_name); continue; } - hose->first_busno = bus_range[0]; + hose->first_busno = hose->self_busno = bus_range[0]; hose->last_busno = bus_range[1]; model = of_get_property(dev, "model", NULL); -- cgit v1.2.3