From c7f43e451ba40e66a89d51e63bc21a57824592f2 Mon Sep 17 00:00:00 2001 From: Luciano Coelho Date: Fri, 11 Dec 2009 15:40:44 +0200 Subject: wl1271: use join command with dummy BSSID When we need to change the channel before association, we have to send a join command with a valid BSSID. With this patch we use 0baddeadbeef as the BSSID. There are ongoing discussions with TI to get this done in a cleaner way. When we go back to idle, we issue a CMD_DISCONNECT to make sure the firmware stops listening to the channel and cleans things up internally. Signed-off-by: Luciano Coelho Reviewed-by: Juuso Oikarinen Signed-off-by: John W. Linville --- drivers/net/wireless/wl12xx/wl1271_main.c | 75 ++++++++++++++++++++++++++----- 1 file changed, 65 insertions(+), 10 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/wl12xx/wl1271_main.c b/drivers/net/wireless/wl12xx/wl1271_main.c index f1cb7cbd7c1..f6d42e613a5 100644 --- a/drivers/net/wireless/wl12xx/wl1271_main.c +++ b/drivers/net/wireless/wl12xx/wl1271_main.c @@ -1130,6 +1130,47 @@ out: } #endif +static int wl1271_join_channel(struct wl1271 *wl, int channel) +{ + int ret; + /* we need to use a dummy BSSID for now */ + static const u8 dummy_bssid[ETH_ALEN] = { 0x0b, 0xad, 0xde, + 0xad, 0xbe, 0xef }; + + /* disable mac filter, so we hear everything */ + wl->rx_config &= ~CFG_BSSID_FILTER_EN; + + wl->channel = channel; + memcpy(wl->bssid, dummy_bssid, ETH_ALEN); + + ret = wl1271_cmd_join(wl); + if (ret < 0) + goto out; + + wl->joined = true; + +out: + return ret; +} + +static int wl1271_unjoin_channel(struct wl1271 *wl) +{ + int ret; + + /* to stop listening to a channel, we disconnect */ + ret = wl1271_cmd_disconnect(wl); + if (ret < 0) + goto out; + + wl->joined = false; + wl->channel = 0; + memset(wl->bssid, 0, ETH_ALEN); + wl->rx_config = WL1271_DEFAULT_RX_CONFIG; + +out: + return ret; +} + static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed) { struct wl1271 *wl = hw->priv; @@ -1138,10 +1179,11 @@ static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed) channel = ieee80211_frequency_to_channel(conf->channel->center_freq); - wl1271_debug(DEBUG_MAC80211, "mac80211 config ch %d psm %s power %d", + wl1271_debug(DEBUG_MAC80211, "mac80211 config ch %d psm %s power %d %s", channel, conf->flags & IEEE80211_CONF_PS ? "on" : "off", - conf->power_level); + conf->power_level, + conf->flags & IEEE80211_CONF_IDLE ? "idle" : "in use"); mutex_lock(&wl->mutex); @@ -1151,16 +1193,17 @@ static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed) if (ret < 0) goto out; - if (channel != wl->channel) { - /* - * We assume that the stack will configure the right channel - * before associating, so we don't need to send a join - * command here. We will join the right channel when the - * BSSID changes - */ - wl->channel = channel; + if (changed & IEEE80211_CONF_CHANGE_IDLE) { + if (conf->flags & IEEE80211_CONF_IDLE && wl->joined) + wl1271_unjoin_channel(wl); + else + wl1271_join_channel(wl, channel); } + /* if the channel changes while joined, join again */ + if (channel != wl->channel && wl->joined) + wl1271_join_channel(wl, channel); + if (conf->flags & IEEE80211_CONF_PS && !wl->psm_requested) { wl1271_info("psm enabled"); @@ -1494,6 +1537,18 @@ static void wl1271_op_bss_info_changed(struct ieee80211_hw *hw, if (ret < 0) goto out; + if ((changed & BSS_CHANGED_BSSID) && + /* + * Now we know the correct bssid, so we send a new join command + * and enable the BSSID filter + */ + memcmp(wl->bssid, bss_conf->bssid, ETH_ALEN)) { + wl->rx_config |= CFG_BSSID_FILTER_EN; + memcpy(wl->bssid, bss_conf->bssid, ETH_ALEN); + wl1271_cmd_join(wl); + wl->joined = true; + } + if (changed & BSS_CHANGED_ASSOC) { if (bss_conf->assoc) { wl->aid = bss_conf->aid; -- cgit v1.2.3