| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This patch explicitly initializes McBSP Transmit Configuration
Control Register (XCCR) and Receive Configuration Control
Register (RCCR) to their reset values. Reset values are 26 ns
of DX delay and Transmit DMA disabled for XCCR register;
receive full cycle mode enabled and Receive DMA disabled for
RCCR register.
This patch requires a counterpart in OMAP McBSP driver before
to apply it. The required changes in McBSP were sent and approved
in linux-omap mailing list and patch is going upstream
(commit 3127f8f8595a064b3f1a1837fea2177902589ac3 from linux-omap-2.6
tree).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
[ jarkko.nikula@nokia.com: Commit id for counterpart patch corrected ]
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The WM8753 driver multiplexes the DAI structures it exposes to the
outside world, leaving them uninitialised until the codec probes. Since
the DAI name is used during the registration and setup process provide a
dummy name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Many people get it wrong and add device IDs into hid_blacklist instead
of hid_ignore_list. Let's put a little comment in place.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
hid_ignore_list additions for the Antec-branded SoundGraph iMon VFD and LCD
devices (0x15c2:0x0044 and 0x0045).
These devices are driven by lirc.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The logic for testing for disconnection is reversed in an ioctl leading
to false reports of disconnection.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Report descriptor fixup for MS 1028 receiver changes also values for
Keyboard and Consumer, which incorrectly trims the range, causing correct
events being thrown away before passing to userspace.
We need to keep the GenDesk usage fixup though, as it reports totally bogus
values about axis.
Reported-by: Lucas Gadani <lgadani@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The sockaddr declared on the stack in cifs_get_tcp_session is too small
for IPv6 addresses. Change it from "struct sockaddr" to "struct
sockaddr_storage" to prevent stack corruption when IPv6 is used.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
nonblocking cases
We have used approximately 15 second timeouts on nonblocking sends in the past, and
also 15 second SMB timeout (waiting for server responses, for most request types).
Now that we can do blocking tcp sends,
make blocking send timeout approximately the same (15 seconds).
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
When a search is pending of a parent directory, and a child directory
within it is removed, we need to reset the parent directory's time
so that we don't reuse the (now stale) search results.
Thanks to Gunter Kukkukk for reporting this:
> got the following failure notification on irc #samba:
>
> A user was updating from subversion 1.4 to 1.5, where the
> repository is located on a samba share (independent of
> unix extensions = Yes or No).
> svn 1.4 did work, 1.5 does not.
>
> The user did a lot of stracing of subversion - and wrote a
> testapplet to simulate the failing behaviour.
> I've converted the C++ source to C and added some error cases.
>
> When using "./testdir" on a local file system, "result2"
> is always (nil) as expected - cifs vfs behaves different here!
>
> ./testdir /mnt/cifs/mounted/share
>
> returns a (failing) valid pointer.
Acked-by: Dave Kleikamp <shaggy@us.ibm.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
When rt modules were added they (each) included their own md5
with names which collided with the existing names of cifs's md5 functions.
Renaming cifs's md5 modules so we don't collide with them.
> Stephen Rothwell wrote:
> When CIFS is built-in (=y) and staging/rt28[67]0 =y, there are multiple
> definitions of:
>
> build-r8250.out:(.text+0x1d8ad0): multiple definition of `MD5Init'
> build-r8250.out:(.text+0x1dbb30): multiple definition of `MD5Update'
> build-r8250.out:(.text+0x1db9b0): multiple definition of `MD5Final'
>
> all of which need to have more unique identifiers for their global
> symbols (e.g., rt28_md5_init, cifs_md5_init, foo, blah, bar).
>
CC: Greg K-H <gregkh@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
cifs: turn smb_send into a wrapper around smb_sendv
Rename smb_send2 to smb_sendv to make it consistent with kernel naming
conventions for functions that take a vector.
There's no need to have 2 functions to handle sending SMB calls. Turn
smb_send into a wrapper around smb_sendv. This also allows us to
properly mark the socket as needing to be reconnected when there's a
partial send from smb_send.
Also, in practice we always use the address and noblocksnd flag
that's attached to the TCP_Server_Info. There's no need to pass
them in as separate args to smb_sendv.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Fix function parameter name in kernel-doc:
Warning(linux-next-20090120//drivers/base/core.c:1289): No description found for parameter 'dev'
Warning(linux-next-20090120//drivers/base/core.c:1289): Excess function parameter 'root' description in 'root_device_unregister'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The following features were added to the UIO framework in the near past:
* Generic drivers for platform devices (uio_pdrv, uio_pdrv_genirq)
* an "offset" sysfs attribute for memory mappings
Unfortunately, all this went in without documentation (won't happen again...)
This patch updates UIO documentation.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Uwe Kleine-König <ukleinek@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Updated jp_JP/stable_kernel_rules.txt due to changes in the main version
of the file.
Also, this patch is already reviewed by Japanese translation community
called JF.
Signed-off-by: Tsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
fix verification of memory area
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
kernel_thread may fail, notice this.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On m68k:
drivers/staging/agnx/agnx.h: In function 'agnx_read32':
drivers/staging/agnx/agnx.h:10: error: implicit declaration of function 'ioread32'
drivers/staging/agnx/agnx.h: In function 'agnx_write32':
drivers/staging/agnx/agnx.h:15: error: implicit declaration of function 'iowrite32'
drivers/staging/agnx/sta.c: In function 'get_sta_power':
drivers/staging/agnx/sta.c:94: error: implicit declaration of function 'memcpy_fromio'
drivers/staging/agnx/sta.c: In function 'set_sta_power':
drivers/staging/agnx/sta.c:103: error: implicit declaration of function 'memcpy_toio'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Compile tested.
task_struct->signal is not protected by RCU, the code is bogus.
Change the code to take ->siglock to pin ->signal.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Brian Swetland <swetland@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
ktime_t isn't ment to directly access on all arches, so use the proper
conversion functions instead to figure out what time is remaining.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Mike Lockwood <lockwood@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mike Lockwood <lockwood@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Meilhaus drivers do not like being built into the kernel right now,
so force them to be a module.
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
comedi doesn't like being built into the kernel right now, so force it
to be a module.
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Reported-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
who also provided a first version of the fix.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
1394-2008 clause 16.3.4.1 (1394b-2002 clause 16.3.1.1) defines tighter
limits than 1394-2008 clause 6.2.2.3 (1394a-2000 clause 6.2.2.3).
Our previously too large limit doesn't matter though if the controller
reports its max_receive correctly.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This makes sbp2 behave more like firewire-sbp2 which reports 0xff000000
as immediate value if there are no unit directory entries for model_id
or firmware_revision.
It does not reduce matches with the currently existing quirks table; the
only zero entry there is for a device which actually does have a zero
model_id. It only changes how model_id and firmware_revision are logged
if they are missing.
Other functionally unrelated changes: The model_id member of quirks
list entries is renamed to model; the value (but not the effect) of
SBP2_ROM_VALUE_WILDCARD is changed. Now this part of the source is
identical with firewire-sbp2 for easier maintenance.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
1394-2008 clause 16.3.4.1 (1394b-2002 clause 16.3.1.1) defines tighter
limits than 1394-2008 clause 6.2.2.3 (1394a-2000 clause 6.2.2.3).
Our previously too large limit doesn't matter though if the controller
reports its max_receive correctly.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The hard-wired configuration of the top speed (until now S800) was
unnecessary, remove it.
If the local link layer controller supports S1600 or S3200, we now
assume this speed for all present 1394b PHYs (except if they are
behind 1394a repeaters) until nodemgr figured out the actual speed
while fetching the config ROM.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
powerpc/pseries: Correct VIO bus accounting problem in CMO env.
powerpc: More printing warning fixes for the l64 to ll64 conversion
powerpc: Remove arch/ppc cruft from Kconfig
powerpc: Printing fix for l64 to ll64 conversion: phyp_dump.c
powerpc/embedded6xx: Update defconfigs
powerpc/8xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/mpc8313erdb: fix kernel panic because mdio device is not probed
powerpc/4xx: Update multi-board PowerPC 4xx defconfigs
powerpc/44x: Update PowerPC 44x defconfigs
powerpc/40x: Update PowerPC 40x defconfigs
powerpc/85xx: Fix typo in mpc8572ds dts
powerpc/44x: Warp patches for the new NDFC driver
powerpc/4xx: DTS: Add Add'l SDRAM0 Compatible and Interrupt Info
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 5329 ColdFire periphal addressing
uclinux: add process name to allocation error message
m68knommu: correct the mii calculations for 532x ColdFire FEC
m68knommu: add ColdFire M532x to the FEC configuration options
m68knommu: fix syscall restarting
m68knommu: remove the obsolete and long unused comempci chip support
m68knommu: remove the no longer used PCI support option
m68knommu: remove obsolete and unused eLIA board
m68knommu: set NO_DMA
m68knommu: fix cache flushing for the 527x ColdFire processors
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
m68knommu: use one exist from execption
|
|
Commit d7b1956fed33d30c4815e848fd7a143722916868 ("DMI: Introduce
dmi_first_match to make the interface more flexible") introduced compile
errors like the following when !CONFIG_DMI
drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast
We just need a dummy version of dmi_first_match() to fix this all up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Schedule a vblank signal, kill the process, and we'll go walking over freed
memory. Given that no open-source userland exists using this, nor have I
ever heard of a consumer, just let this code die.
Signed-off-by: Eric Anholt <eric@anholt.net>
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add another MacBook Pro 4,1 SSID (106b:3800). It seems that latter revisions,
(at least mine), have different IDs to earlier revisions.
Signed-off-by: Luke Yelavich <themuso@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.
This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE. Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE. Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system. Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.
Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should. Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Remove some leftover cruft from the arch/ppc days
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Manual merge of:
arch/powerpc/configs/44x/warp_defconfig
|
|
|
|
Given just how hard it is to find the code that uses MAY_APPEND
it's probably not a big surprise that this went unnoticed for so
long. The Smack rules loading code is incorrectly setting the
MAY_READ bit when MAY_APPEND is requested.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
USB: Driver for Freescale QUICC Engine USB Host Controller
USB: option: add QUANTA HSDPA Data Card device ids
USB: storage: Add another unusual_dev for off-by-one bug
USB: unusual_dev: usb-storage needs to ignore a device
USB: GADGET: fix !x & y
USB: new id for ti_usb_3410_5052 driver
USB: cdc-acm: Add another conexant modem to the quirks
USB: 'option' driver - onda device MT503HS has wrong id
USB: Remove ZTE modem from unusual_devices
USB: storage: support of Dane-Elec MediaTouch USB device
USB: usbmon: Implement compat_ioctl
USB: add kernel-doc for wusb_dev in struct usb_device
USB: ftdi_sio driver support of bar code scanner from Diebold
USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
USB: cp2101 device
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
USB: remove vernier labpro from ldusb
USB: CDC-ACM quirk for MTK GPS
USB: cdc-acm: support some gps data loggers
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
...
|
|
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
