From 1a1b172b9672e88d37adb5925b509e9236625d7e Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Mon, 7 Dec 2009 23:30:06 +0400 Subject: pata_hpt{37x|3x2n}: unify mode programming As these drivers' set_piomode() and set_dmamode() methods are almost identical, factor out the common hpt{37x|3x2n}_set_mode() function to be called by both of them, the same as in 'pata_hpt366' driver. This results in ~5% decrease in the 'pata_hpt37x' driver binary size and in ~4% decrease in the 'pata_hpt3x2n' driver binary size (as measured on x86-32). Signed-off-by: Sergei Shtylyov Signed-off-by: Jeff Garzik --- drivers/ata/pata_hpt3x2n.c | 69 +++++++++++++++++++++------------------------- 1 file changed, 31 insertions(+), 38 deletions(-) (limited to 'drivers/ata/pata_hpt3x2n.c') diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c index 269b5dbe51b..b131c8f824d 100644 --- a/drivers/ata/pata_hpt3x2n.c +++ b/drivers/ata/pata_hpt3x2n.c @@ -25,7 +25,7 @@ #include #define DRV_NAME "pata_hpt3x2n" -#define DRV_VERSION "0.3.9" +#define DRV_VERSION "0.3.10" enum { HPT_PCI_FAST = (1 << 31), @@ -161,20 +161,12 @@ static int hpt3x2n_pre_reset(struct ata_link *link, unsigned long deadline) return ata_sff_prereset(link, deadline); } -/** - * hpt3x2n_set_piomode - PIO setup - * @ap: ATA interface - * @adev: device on the interface - * - * Perform PIO mode setup. - */ - -static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) +static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev, + u8 mode) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); u32 addr1, addr2; - u32 reg; - u32 mode; + u32 reg, timing, mask; u8 fast; addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); @@ -185,11 +177,32 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) fast &= ~0x07; pci_write_config_byte(pdev, addr2, fast); + /* Determine timing mask and find matching mode entry */ + if (mode < XFER_MW_DMA_0) + mask = 0xcfc3ffff; + else if (mode < XFER_UDMA_0) + mask = 0x31c001ff; + else + mask = 0x303c0000; + + timing = hpt3x2n_find_mode(ap, mode); + pci_read_config_dword(pdev, addr1, ®); - mode = hpt3x2n_find_mode(ap, adev->pio_mode); - mode &= 0xCFC3FFFF; /* Leave DMA bits alone */ - reg &= ~0xCFC3FFFF; /* Strip timing bits */ - pci_write_config_dword(pdev, addr1, reg | mode); + reg = (reg & ~mask) | (timing & mask); + pci_write_config_dword(pdev, addr1, reg); +} + +/** + * hpt3x2n_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Perform PIO mode setup. + */ + +static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + hpt3x2n_set_mode(ap, adev, adev->pio_mode); } /** @@ -197,32 +210,12 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) * @ap: ATA interface * @adev: Device being configured * - * Set up the channel for MWDMA or UDMA modes. Much the same as with - * PIO, load the mode number and then set MWDMA or UDMA flag. + * Set up the channel for MWDMA or UDMA modes. */ static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev) { - struct pci_dev *pdev = to_pci_dev(ap->host->dev); - u32 addr1, addr2; - u32 reg, mode, mask; - u8 fast; - - addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); - addr2 = 0x51 + 4 * ap->port_no; - - /* Fast interrupt prediction disable, hold off interrupt disable */ - pci_read_config_byte(pdev, addr2, &fast); - fast &= ~0x07; - pci_write_config_byte(pdev, addr2, fast); - - mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000; - - pci_read_config_dword(pdev, addr1, ®); - mode = hpt3x2n_find_mode(ap, adev->dma_mode); - mode &= mask; - reg &= ~mask; - pci_write_config_dword(pdev, addr1, reg | mode); + hpt3x2n_set_mode(ap, adev, adev->dma_mode); } /** -- cgit v1.2.3