Merge with /home/wd/git/u-boot/jon_loeliger

50 files changed, 3584 insertions, 150 deletions

diff --git a/include/asm-ppc/e300.h b/include/asm-ppc/e300.h
new file mode 100644
index 000000000..908007cbc
--- /dev/null
+++ b/include/asm-ppc/e300.h
@@ -0,0 +1,128 @@
+/*
+ * Copyright 2004 Freescale Semiconductor, Inc.
+ * Liberty Eran (liberty@freescale.com)
+ */
+
+#ifndef	__E300_H__
+#define __E300_H__
+
+/*
+ * e300 Processor Version & Revision Numbers
+ */
+#define PVR_83xx 0x80830000
+#define PVR_8349_REV10 (PVR_83xx | 0x0010)
+#define PVR_8349_REV11 (PVR_83xx | 0x0011)
+
+/*
+ * Hardware Implementation-Dependent Register 0 (HID0)
+ */
+
+/* #define HID0 1008 already defined in processor.h */
+#define HID0_MASK_MACHINE_CHECK              0x00000000
+#define HID0_ENABLE_MACHINE_CHECK            0x80000000
+
+#define HID0_DISABLE_CACHE_PARITY            0x00000000
+#define HID0_ENABLE_CACHE_PARITY             0x40000000
+
+#define HID0_DISABLE_ADDRESS_PARITY          0x00000000 /* on mpc8349ads must be disabled */
+#define HID0_ENABLE_ADDRESS_PARITY           0x20000000
+
+#define HID0_DISABLE_DATA_PARITY             0x00000000 /* on mpc8349ads must be disabled */
+#define HID0_ENABLE_DATE_PARITY              0x10000000
+
+#define HID0_CORE_CLK_OUT                    0x00000000
+#define HID0_CORE_CLK_OUT_DIV_2              0x08000000
+
+#define HID0_ENABLE_ARTRY_OUT_PRECHARGE      0x00000000 /* on mpc8349ads must be enabled */
+#define HID0_DISABLE_ARTRY_OUT_PRECHARGE     0x01000000
+
+#define HID0_DISABLE_DOSE_MODE               0x00000000
+#define HID0_ENABLE_DOSE_MODE                0x00800000
+
+#define HID0_DISABLE_NAP_MODE                0x00000000
+#define HID0_ENABLE_NAP_MODE                 0x00400000
+
+#define HID0_DISABLE_SLEEP_MODE              0x00000000
+#define HID0_ENABLE_SLEEP_MODE               0x00200000
+
+#define HID0_DISABLE_DYNAMIC_POWER_MANAGMENT 0x00000000
+#define HID0_ENABLE_DYNAMIC_POWER_MANAGMENT  0x00100000
+
+#define HID0_SOFT_RESET                      0x00010000
+
+#define HID0_DISABLE_INSTRUCTION_CACHE       0x00000000
+#define HID0_ENABLE_INSTRUCTION_CACHE        0x00008000
+
+#define HID0_DISABLE_DATA_CACHE              0x00000000
+#define HID0_ENABLE_DATA_CACHE               0x00004000
+
+#define HID0_LOCK_INSTRUCTION_CACHE          0x00002000
+
+#define HID0_LOCK_DATA_CACHE                 0x00001000
+
+#define HID0_INVALIDATE_INSTRUCTION_CACHE    0x00000800
+
+#define HID0_INVALIDATE_DATA_CACHE           0x00000400
+
+#define HID0_DISABLE_M_BIT                   0x00000000
+#define HID0_ENABLE_M_BIT                    0x00000080
+
+#define HID0_FBIOB                           0x00000010
+
+#define HID0_DISABLE_ADDRESS_BROADCAST       0x00000000
+#define HID0_ENABLE_ADDRESS_BROADCAST        0x00000008
+
+#define HID0_ENABLE_NOOP_DCACHE_INSTRUCTION  0x00000000
+#define HID0_DISABLE_NOOP_DCACHE_INSTRUCTION 0x00000001
+
+/*
+ * Hardware Implementation-Dependent Register 2 (HID2)
+ */
+#define HID2		1011
+
+#define HID2_LET       0x08000000
+#define HID2_HBE       0x00040000
+#define HID2_IWLCK_000 0x00000000 /* no ways locked */
+#define HID2_IWLCK_001 0x00002000 /* way 0 locked */
+#define HID2_IWLCK_010 0x00004000 /* way 0 through way 1 locked */
+#define HID2_IWLCK_011 0x00006000 /* way 0 through way 2 locked */
+#define HID2_IWLCK_100 0x00008000 /* way 0 through way 3 locked */
+#define HID2_IWLCK_101 0x0000A000 /* way 0 through way 4 locked */
+#define HID2_IWLCK_110 0x0000C000 /* way 0 through way 5 locked */
+
+
+/* BAT (block address translation */
+#define BATU_BEPI_MSK	    0xfffe0000
+#define BATU_BL_MSK         0x00001ffc
+
+#define BATU_BL_128K        0x00000000
+#define BATU_BL_256K        0x00000004
+#define BATU_BL_512K        0x0000000c
+#define BATU_BL_1M          0x0000001c
+#define BATU_BL_2M          0x0000003c
+#define BATU_BL_4M          0x0000007c
+#define BATU_BL_8M          0x000000fc
+#define BATU_BL_16M         0x000001fc
+#define BATU_BL_32M         0x000003fc
+#define BATU_BL_64M         0x000007fc
+#define BATU_BL_128M        0x00000ffc
+#define BATU_BL_256M        0x00001ffc
+
+#define BATU_VS             0x00000002
+#define BATU_VP             0x00000001
+
+#define BATL_BRPN_MSK       0xfffe0000
+#define BATL_WIMG_MSK       0x00000078
+
+#define BATL_WRITETHROUGH   0x00000040
+#define BATL_CACHEINHIBIT   0x00000020
+#define BATL_MEMCOHERENCE   0x00000010
+#define BATL_GUARDEDSTORAGE 0x00000008
+
+#define BATL_PP_MSK         0x00000003
+#define BATL_PP_00          0x00000000 /* No access */
+#define BATL_PP_01          0x00000001 /* Read-only */
+#define BATL_PP_10          0x00000002 /* Read-write */
+#define BATL_PP_11        	0x00000003
+
+#endif	/* __E300_H__ */
diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h
index c800f63cc..9681a74b5 100644
--- a/include/asm-ppc/global_data.h
+++ b/include/asm-ppc/global_data.h
@@ -23,6 +23,9 @@
 
 #ifndef	__ASM_GBL_DATA_H
 #define __ASM_GBL_DATA_H
+
+#include "asm/types.h"
+
 /*
  * The following data structure is placed in some memory wich is
  * available very early after boot (like DPRAM on MPC8xx/MPC82xx, or
@@ -39,13 +42,27 @@ typedef	struct	global_data {
 	unsigned long	baudrate;
 	unsigned long	cpu_clk;	/* CPU clock in Hz!		*/
 	unsigned long	bus_clk;
-#if defined(CONFIG_8260) || defined(CONFIG_MPC8560)
+#if defined(CONFIG_CPM2)
 	/* There are many clocks on the MPC8260 - see page 9-5 */
 	unsigned long	vco_out;
 	unsigned long	cpm_clk;
 	unsigned long	scc_clk;
 	unsigned long	brg_clk;
 #endif
+#if defined(CONFIG_MPC83XX)
+	/* There are other clocks in the MPC83XX */
+	u32 csb_clk;
+	u32 tsec1_clk;
+	u32 tsec2_clk;
+	u32 core_clk;
+	u32 usbmph_clk;
+	u32 usbdr_clk;
+	u32 i2c_clk;
+	u32 enc_clk;
+	u32 lbiu_clk;
+	u32 lclk_clk;
+	u32 ddr_clk;
+#endif
 #if defined(CONFIG_MPC5xxx)
 	unsigned long	ipb_clk;
 	unsigned long	pci_clk;
@@ -64,7 +81,7 @@ typedef	struct	global_data {
 	unsigned long	env_addr;	/* Address  of Environment struct	*/
 	unsigned long	env_valid;	/* Checksum of Environment valid?	*/
 	unsigned long	have_console;	/* serial_init() was called		*/
-#if defined(CFG_ALLOC_DPRAM) || defined(CONFIG_8260) || defined(CONFIG_MPC8560)
+#if defined(CFG_ALLOC_DPRAM) || defined(CONFIG_CPM2)
 	unsigned int	dp_alloc_base;
 	unsigned int	dp_alloc_top;
 #endif
diff --git a/include/asm-ppc/i2c.h b/include/asm-ppc/i2c.h
new file mode 100644
index 000000000..2a4ac0ff3
--- /dev/null
+++ b/include/asm-ppc/i2c.h
@@ -0,0 +1,103 @@
+/*
+ * Freescale I2C Controller
+ *
+ * This software may be used and distributed according to the
+ * terms of the GNU Public License, Version 2, incorporated
+ * herein by reference.
+ *
+ * Copyright 2004 Freescale Semiconductor.
+ * (C) Copyright 2003, Motorola, Inc.
+ * author: Eran Liberty (liberty@freescale.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _ASM_I2C_H_
+#define _ASM_I2C_H_
+
+#include <asm/types.h>
+
+typedef struct i2c
+{
+    u8 adr;          /**< I2C slave address              */
+#define I2C_ADR	      0xFE
+#define I2C_ADR_SHIFT 1
+#define I2C_ADR_RES   ~(I2C_ADR)
+    u8 res0[3];
+    u8 fdr;          /**< I2C frequency divider register */
+#define IC2_FDR       0x3F
+#define IC2_FDR_SHIFT 0
+#define IC2_FDR_RES   ~(IC2_FDR)
+    u8 res1[3];
+    u8 cr;           /**< I2C control redister           */
+#define I2C_CR_MEN	  0x80
+#define I2C_CR_MIEN	  0x40
+#define I2C_CR_MSTA   0x20
+#define I2C_CR_MTX    0x10
+#define I2C_CR_TXAK   0x08
+#define I2C_CR_RSTA   0x04
+#define I2C_CR_BCST   0x01
+    u8 res2[3];
+    u8 sr;           /**< I2C status register            */
+#define I2C_SR_MCF    0x80
+#define I2C_SR_MAAS   0x40
+#define I2C_SR_MBB    0x20
+#define I2C_SR_MAL    0x10
+#define I2C_SR_BCSTM  0x08
+#define I2C_SR_SRW    0x04
+#define I2C_SR_MIF    0x02
+#define I2C_SR_RXAK   0x01
+    u8 res3[3];
+    u8 dr;           /**< I2C data register              */
+#define I2C_DR 0xFF
+#define I2C_DR_SHIFT 0
+#define I2C_DR_RES ~(I2C_DR)
+    u8 res4[3];
+    u8 dfsrr;        /**< I2C digital filter sampling rate register */
+#define I2C_DFSRR 0x3F
+#define I2C_DFSRR_SHIFT 0
+#define I2C_DFSRR_RES ~(I2C_DR)
+    u8 res5[3];
+    u8 res6[0xE8];
+} i2c_t;
+
+#ifndef CFG_HZ
+#error CFG_HZ is not defined in /include/configs/${BOARD}.h
+#endif
+#define I2C_TIMEOUT (CFG_HZ/4)
+
+#ifndef CFG_IMMRBAR
+#error CFG_IMMRBAR is not defined in /include/configs/${BOARD}.h
+#endif
+
+#ifndef CFG_I2C_OFFSET
+#error CFG_I2C_OFFSET is not defined in /include/configs/${BOARD}.h
+#endif
+
+#ifdef CONFIG_MPC8349ADS
+/*
+ * MPC8349 have two i2c bus
+ */
+extern i2c_t * mpc8349_i2c;
+#define I2C mpc8349_i2c
+#else
+#define I2C ((i2c_t*)(CFG_IMMRBAR + CFG_I2C_OFFSET))
+#endif
+
+#define I2C_READ  1
+#define I2C_WRITE 0
+
+#endif	/* _ASM_I2C_H_ */
diff --git a/include/asm-ppc/immap_83xx.h b/include/asm-ppc/immap_83xx.h
new file mode 100644
index 000000000..5d284d467
--- /dev/null
+++ b/include/asm-ppc/immap_83xx.h
@@ -0,0 +1,1060 @@
+/*
+ * MPC8349 Internal Memory Map
+ * Copyright (c) 2004 Freescale Semiconductor.
+ * Eran Liberty (liberty@freescale.com)
+ *
+ * based on:
+ * - MPC8260 Internal Memory Map
+ *   Copyright (c) 1999 Dan Malek (dmalek@jlc.net)
+ * - MPC85xx Internal Memory Map
+ *   Copyright(c) 2002,2003 Motorola Inc.
+ *   Xianghua Xiao (x.xiao@motorola.com)
+ */
+#ifndef __IMMAP_8349__
+#define __IMMAP_8349__
+
+#include <asm/types.h>
+#include <asm/i2c.h>
+
+/*
+ * Local Access Window.
+ */
+typedef struct law8349 {
+	u32 bar; /* LBIU local access window base address register */
+/* Identifies the 20 most-significant address bits of the base of local
+ * access window n. The specified base address should be aligned to the
+ * window size, as defined by LBLAWARn[SIZE].
+ */
+#define LAWBAR_BAR         0xFFFFF000
+#define LAWBAR_RES	     ~(LAWBAR_BAR)
+	u32 ar; /* LBIU local access window attribute register */
+/*
+ * This Macro were moved into mmu.h
+ */
+#if 0
+/* 0 The local bus local access window n is disabled. 1 The local bus
+ * local access window n is enabled and other LBLAWAR0 and LBLAWBAR0 fields
+ * combine to identify an address range for this window.
+ */
+#define LAWAR_EN           0x80000000
+/* Identifies the size of the window from the starting address. Window
+ * size is 2^(SIZE+1) bytes. 000000–001010Reserved. Window is
+ * undefined.
+ */
+#define LAWAR_SIZE         0x0000003F
+#define	LAWAR_SIZE_4K	0x0000000B
+#define	LAWAR_SIZE_8K	0x0000000C
+#define	LAWAR_SIZE_16K	0x0000000D
+#define	LAWAR_SIZE_32K	0x0000000E
+#define	LAWAR_SIZE_64K	0x0000000F
+#define	LAWAR_SIZE_128K	0x00000010
+#define	LAWAR_SIZE_256K	0x00000011
+#define	LAWAR_SIZE_512K	0x00000012
+#define	LAWAR_SIZE_1M	0x00000013
+#define	LAWAR_SIZE_2M	0x00000014
+#define	LAWAR_SIZE_4M	0x00000015
+#define	LAWAR_SIZE_8M	0x00000016
+#define	LAWAR_SIZE_16M	0x00000017
+#define	LAWAR_SIZE_32M	0x00000018
+#define	LAWAR_SIZE_64M	0x00000019
+#define	LAWAR_SIZE_128M	0x0000001A
+#define	LAWAR_SIZE_256M	0x0000001B
+#define	LAWAR_SIZE_512M	0x0000001C
+#define	LAWAR_SIZE_1G	0x0000001D
+#define	LAWAR_SIZE_2G	0x0000001E
+#define LAWAR_RES          ~(LAWAR_EN|LAWAR_SIZE)
+#endif
+
+} law8349_t;
+
+/*
+ * System configuration registers.
+ */
+typedef struct sysconf8349 {
+	u32 immrbar; /* Internal memory map base address register */
+	u8 res0[0x04];
+	u32 altcbar; /* Alternate configuration base address register */
+/* Identifies the12 most significant address bits of an alternate base
+ * address used for boot sequencer configuration accesses.
+ */
+#define ALTCBAR_BASE_ADDR     0xFFF00000
+#define ALTCBAR_RES           ~(ALTCBAR_BASE_ADDR) /* Reserved. Write has no effect, read returns 0. */
+	u8 res1[0x14];
+	law8349_t lblaw[4]; /* LBIU local access window */
+	u8 res2[0x20];
+	law8349_t pcilaw[2]; /* PCI local access window */
+	u8 res3[0x30];
+	law8349_t ddrlaw[2]; /* DDR local access window */
+	u8 res4[0x50];
+	u32 sgprl; /* System General Purpose Register Low */
+	u32 sgprh; /* System General Purpose Register High */
+	u32 spridr; /* System Part and Revision ID Register */
+#define SPRIDR_PARTID         0xFFFF0000 /* Part Identification. */
+#define SPRIDR_REVID          0x0000FFFF /* Revision Identification. */
+	u8 res5[0x04];
+	u32 spcr; /* System Priority Configuration Register */
+#define SPCR_PCIHPE   0x10000000 /* PCI Highest Priority Enable. */
+#define SPCR_PCIPR    0x03000000 /* PCI bridge system bus request priority. */
+#define SPCR_TBEN     0x00400000 /* E300 PowerPC core time base unit enable. */
+#define SPCR_COREPR   0x00300000 /* E300 PowerPC Core system bus request priority. */
+#define SPCR_TSEC1DP  0x00003000 /* TSEC1 data priority. */
+#define SPCR_TSEC1BDP 0x00000C00 /* TSEC1 buffer descriptor priority. */
+#define SPCR_TSEC1EP  0x00000300 /* TSEC1 emergency priority. */
+#define SPCR_TSEC2DP  0x00000030 /* TSEC2 data priority. */
+#define SPCR_TSEC2BDP 0x0000000C /* TSEC2 buffer descriptor priority. */
+#define SPCR_TSEC2EP  0x00000003 /* TSEC2 emergency priority. */
+#define SPCR_RES      ~(SPCR_PCIHPE | SPCR_PCIPR | SPCR_TBEN | SPCR_COREPR \
+			| SPCR_TSEC1DP | SPCR_TSEC1BDP | SPCR_TSEC1EP \
+			| SPCR_TSEC2DP | SPCR_TSEC2BDP | SPCR_TSEC2EP)
+	u32 sicrl; /* System General Purpose Register Low */
+#define SICRL_LDP_A   0x80000000
+#define SICRL_USB0    0x40000000
+#define SICRL_USB1    0x20000000
+#define SICRL_UART    0x0C000000
+#define SICRL_GPIO1_A 0x02000000
+#define SICRL_GPIO1_B 0x01000000
+#define SICRL_GPIO1_C 0x00800000
+#define SICRL_GPIO1_D 0x00400000
+#define SICRL_GPIO1_E 0x00200000
+#define SICRL_GPIO1_F 0x00180000
+#define SICRL_GPIO1_G 0x00040000
+#define SICRL_GPIO1_H 0x00020000
+#define SICRL_GPIO1_I 0x00010000
+#define SICRL_GPIO1_J 0x00008000
+#define SICRL_GPIO1_K 0x00004000
+#define SICRL_GPIO1_L 0x00003000
+#define SICRL_RES ~(SICRL_LDP_A | SICRL_USB0 | SICRL_USB1 | SICRL_UART \
+			| SICRL_GPIO1_A | SICRL_GPIO1_B | SICRL_GPIO1_C \
+			| SICRL_GPIO1_D | SICRL_GPIO1_E | SICRL_GPIO1_F \
+			| SICRL_GPIO1_G | SICRL_GPIO1_H | SICRL_GPIO1_I \
+			| SICRL_GPIO1_J | SICRL_GPIO1_K | SICRL_GPIO1_L )
+	u32 sicrh; /* System General Purpose Register High */
+#define SICRH_DDR     0x80000000
+#define SICRH_TSEC1_A 0x10000000
+#define SICRH_TSEC1_B 0x08000000
+#define SICRH_TSEC1_C 0x04000000
+#define SICRH_TSEC1_D 0x02000000
+#define SICRH_TSEC1_E 0x01000000
+#define SICRH_TSEC1_F 0x00800000
+#define SICRH_TSEC2_A 0x00400000
+#define SICRH_TSEC2_B 0x00200000
+#define SICRH_TSEC2_C 0x00100000
+#define SICRH_TSEC2_D 0x00080000
+#define SICRH_TSEC2_E 0x00040000
+#define SICRH_TSEC2_F 0x00020000
+#define SICRH_TSEC2_G 0x00010000
+#define SICRH_TSEC2_H 0x00008000
+#define SICRH_GPIO2_A 0x00004000
+#define SICRH_GPIO2_B 0x00002000
+#define SICRH_GPIO2_C 0x00001000
+#define SICRH_GPIO2_D 0x00000800
+#define SICRH_GPIO2_E 0x00000400
+#define SICRH_GPIO2_F 0x00000200
+#define SICRH_GPIO2_G 0x00000180
+#define SICRH_GPIO2_H 0x00000060
+#define SICRH_TSOBI1  0x00000002
+#define SICRH_TSOBI2  0x00000001
+#define SICRh_RES     ~(  SICRH_DDR | SICRH_TSEC1_A | SICRH_TSEC1_B \
+			| SICRH_TSEC1_C | SICRH_TSEC1_D | SICRH_TSEC1_E \
+			| SICRH_TSEC1_F | SICRH_TSEC2_A | SICRH_TSEC2_B \
+			| SICRH_TSEC2_C | SICRH_TSEC2_D | SICRH_TSEC2_E \
+			| SICRH_TSEC2_F | SICRH_TSEC2_G | SICRH_TSEC2_H \
+			| SICRH_GPIO2_A | SICRH_GPIO2_B | SICRH_GPIO2_C \
+			| SICRH_GPIO2_D | SICRH_GPIO2_E | SICRH_GPIO2_F \
+			| SICRH_GPIO2_G | SICRH_GPIO2_H | SICRH_TSOBI1 \
+			| SICRH_TSOBI2)
+	u8 res6[0xE4];
+} sysconf8349_t;
+
+/*
+ * Watch Dog Timer (WDT) Registers
+ */
+typedef struct wdt8349 {
+	u8 res0[4];
+	u32 swcrr; /* System watchdog control register */
+	u32 swcnr; /* System watchdog count register */
+#define SWCNR_SWCN 0x0000FFFF Software Watchdog Count Field.
+#define SWCNR_RES  ~(SWCNR_SWCN)
+	u8 res1[2];
+	u16 swsrr; /* System watchdog service register */
+	u8 res2[0xF0];
+} wdt8349_t;
+
+/*
+ * RTC/PIT Module Registers
+ */
+typedef struct rtclk8349 {
+	u32 cnr; /* control register */
+#define CNR_CLEN 0x00000080 /* Clock Enable Control Bit  */
+#define CNR_CLIN 0x00000040 /* Input Clock Control Bit  */
+#define CNR_AIM  0x00000002 /* Alarm Interrupt Mask Bit  */
+#define CNR_SIM  0x00000001 /* Second Interrupt Mask Bit  */
+#define CNR_RES  ~(CNR_CLEN | CNR_CLIN | CNR_AIM | CNR_SIM)
+	u32 ldr; /* load register */
+	u32 psr; /* prescale register */
+	u32 ctr; /* register */
+	u32 evr; /* event register */
+#define RTEVR_SIF  0x00000001 /* Second Interrupt Flag Bit  */
+#define RTEVR_AIF  0x00000002 /* Alarm Interrupt Flag Bit  */
+#define RTEVR_RES  ~(EVR_SIF | EVR_AIF)
+	u32 alr; /* alarm register */
+	u8 res0[0xE8];
+} rtclk8349_t;
+
+/*
+ * Global timper module
+ */
+
+typedef struct gtm8349 {
+	u8    cfr1; /* Timer1/2 Configuration  */
+#define CFR1_PCAS 0x80 /* Pair Cascade mode  */
+#define CFR1_BCM  0x40  /* Backward compatible mode  */
+#define CFR1_STP2 0x20 /* Stop timer  */
+#define CFR1_RST2 0x10 /* Reset timer  */
+#define CFR1_GM2  0x08 /* Gate mode for pin 2  */
+#define CFR1_GM1  0x04 /* Gate mode for pin 1  */
+#define CFR1_STP1 0x02 /* Stop timer  */
+#define CFR1_RST1 0x01 /* Reset timer  */
+	u8    res0[3];
+	u8    cfr2; /* Timer3/4 Configuration  */
+#define CFR2_PCAS 0x80 /* Pair Cascade mode  */
+#define CFR2_SCAS 0x40 /* Super Cascade mode  */
+#define CFR2_STP4 0x20 /* Stop timer  */
+#define CFR2_RST4 0x10 /* Reset timer  */
+#define CFR2_GM4  0x08 /* Gate mode for pin 4  */
+#define CFR2_GM3  0x04 /* Gate mode for pin 3  */
+#define CFR2_STP3 0x02 /* Stop timer  */
+#define CFR2_RST3 0x01 /* Reset timer  */
+	u8    res1[10];
+	u16   mdr1; /* Timer1 Mode Register  */
+#define MDR_SPS  0xff00 /* Secondary Prescaler value  */
+#define MDR_CE   0x00c0 /* Capture edge and enable interrupt  */
+#define MDR_OM   0x0020 /* Output mode  */
+#define MDR_ORI  0x0010 /* Output reference interrupt enable  */
+#define MDR_FRR  0x0008 /* Free run/restart  */
+#define MDR_ICLK 0x0006 /* Input clock source for the timer  */
+#define MDR_GE   0x0001 /* Gate enable  */
+	u16   mdr2; /* Timer2 Mode Register  */
+	u16   rfr1; /* Timer1 Reference Register  */
+	u16   rfr2; /* Timer2 Reference Register  */
+	u16   cpr1; /* Timer1 Capture Register  */
+	u16   cpr2; /* Timer2 Capture Register  */
+	u16   cnr1; /* Timer1 Counter Register  */
+	u16   cnr2; /* Timer2 Counter Register  */
+	u16   mdr3; /* Timer3 Mode Register  */
+	u16   mdr4; /* Timer4 Mode Register  */
+	u16   rfr3; /* Timer3 Reference Register  */
+	u16   rfr4; /* Timer4 Reference Register  */
+	u16   cpr3; /* Timer3 Capture Register  */
+	u16   cpr4; /* Timer4 Capture Register  */
+	u16   cnr3; /* Timer3 Counter Register  */
+	u16   cnr4; /* Timer4 Counter Register  */
+	u16   evr1; /* Timer1 Event Register  */
+	u16   evr2; /* Timer2 Event Register  */
+	u16   evr3; /* Timer3 Event Register  */
+	u16   evr4; /* Timer4 Event Register  */
+#define GTEVR_REF 0x0002 /* Output reference event  */
+#define GTEVR_CAP 0x0001 /* Counter Capture event   */
+#define GTEVR_RES ~(EVR_CAP|EVR_REF)
+	u16   psr1; /* Timer1 Prescaler Register  */
+	u16   psr2; /* Timer2 Prescaler Register  */
+	u16   psr3; /* Timer3 Prescaler Register  */
+	u16   psr4; /* Timer4 Prescaler Register  */
+	u8    res[0xC0];
+} gtm8349_t;
+
+/*
+ * Integrated Programmable Interrupt Controller
+ */
+typedef struct ipic8349 {
+	u32    sicfr; /*  System Global Interrupt Configuration Register (SICFR)  */
+#define SICFR_HPI  0x7f000000 /*  Highest Priority Interrupt  */
+#define SICFR_MPSB 0x00400000 /*  Mixed interrupts Priority Scheme for group B  */
+#define SICFR_MPSA 0x00200000 /*  Mixed interrupts Priority Scheme for group A  */
+#define SICFR_IPSD 0x00080000 /*  Internal interrupts Priority Scheme for group D  */
+#define SICFR_IPSA 0x00010000 /*  Internal interrupts Priority Scheme for group A  */
+#define SICFR_HPIT 0x00000300 /*  HPI priority position IPIC output interrupt Type  */
+#define SICFR_RES ~(SICFR_HPI|SICFR_MPSB|SICFR_MPSA|SICFR_IPSD|SICFR_IPSA|SICFR_HPIT)
+	u32    sivcr; /*  System Global Interrupt Vector Register (SIVCR)  */
+#define SICVR_IVECX 0xfc000000 /*  Interrupt vector (for CE compatibility purpose only not used in 8349 IPIC implementation)  */
+#define SICVR_IVEC  0x0000007f /*  Interrupt vector  */
+#define SICVR_RES ~(SICVR_IVECX|SICVR_IVEC)
+	u32    sipnr_h; /*  System Internal Interrupt Pending Register - High (SIPNR_H)  */
+#define SIIH_TSEC1TX 0x80000000 /*  TSEC1 Tx interrupt  */
+#define SIIH_TSEC1RX 0x40000000 /*  TSEC1 Rx interrupt  */
+#define SIIH_TSEC1ER 0x20000000 /*  TSEC1 Eror interrupt  */
+#define SIIH_TSEC2TX 0x10000000 /*  TSEC2 Tx interrupt  */
+#define SIIH_TSEC2RX 0x08000000 /*  TSEC2 Rx interrupt  */
+#define SIIH_TSEC2ER 0x04000000 /*  TSEC2 Eror interrupt  */
+#define SIIH_USB2DR  0x02000000 /*  USB2 DR interrupt  */
+#define SIIH_USB2MPH 0x01000000 /*  USB2 MPH interrupt  */
+#define SIIH_UART1   0x00000080 /*  UART1 interrupt  */
+#define SIIH_UART2   0x00000040 /*  UART2 interrupt  */
+#define SIIH_SEC     0x00000020 /*  SEC interrupt  */
+#define SIIH_I2C1    0x00000004 /*  I2C1 interrupt  */
+#define SIIH_I2C2    0x00000002 /*  I2C1 interrupt  */
+#define SIIH_SPI     0x00000001 /*  SPI interrupt  */
+#define SIIH_RES	~(SIIH_TSEC1TX | SIIH_TSEC1RX | SIIH_TSEC1ER \
+			| SIIH_TSEC2TX | SIIH_TSEC2RX | SIIH_TSEC2ER \
+			| SIIH_USB2DR | SIIH_USB2MPH | SIIH_UART1 \
+			| SIIH_UART2 | SIIH_SEC | SIIH_I2C1 \
+			| SIIH_I2C2 | SIIH_SPI)
+	u32    sipnr_l; /*  System Internal Interrupt Pending Register - Low (SIPNR_L)  */
+#define SIIL_RTCS  0x80000000 /*  RTC SECOND interrupt  */
+#define SIIL_PIT   0x40000000 /*  PIT interrupt  */
+#define SIIL_PCI1  0x20000000 /*  PCI1 interrupt  */
+#define SIIL_PCI2  0x10000000 /*  PCI2 interrupt  */
+#define SIIL_RTCA  0x08000000 /*  RTC ALARM interrupt  */
+#define SIIL_MU    0x04000000 /*  Message Unit interrupt  */
+#define SIIL_SBA   0x02000000 /*  System Bus Arbiter interrupt  */
+#define SIIL_DMA   0x01000000 /*  DMA interrupt  */
+#define SIIL_GTM4  0x00800000 /*  GTM4 interrupt  */
+#define SIIL_GTM8  0x00400000 /*  GTM8 interrupt  */
+#define SIIL_GPIO1 0x00200000 /*  GPIO1 interrupt  */
+#define SIIL_GPIO2 0x00100000 /*  GPIO2 interrupt  */
+#define SIIL_DDR   0x00080000 /*  DDR interrupt  */
+#define SIIL_LBC   0x00040000 /*  LBC interrupt  */
+#define SIIL_GTM2  0x00020000 /*  GTM2 interrupt  */
+#define SIIL_GTM6  0x00010000 /*  GTM6 interrupt  */
+#define SIIL_PMC   0x00008000 /*  PMC interrupt  */
+#define SIIL_GTM3  0x00000800 /*  GTM3 interrupt  */
+#define SIIL_GTM7  0x00000400 /*  GTM7 interrupt  */
+#define SIIL_GTM1  0x00000020 /*  GTM1 interrupt  */
+#define SIIL_GTM5  0x00000010 /*  GTM5 interrupt  */
+#define SIIL_DPTC  0x00000001 /*  DPTC interrupt (!!! Invisible for user !!!)  */
+#define SIIL_RES	~(SIIL_RTCS | SIIL_PIT | SIIL_PCI1 | SIIL_PCI2 \
+			| SIIL_RTCA | SIIL_MU | SIIL_SBA | SIIL_DMA \
+			| SIIL_GTM4 | SIIL_GTM8 | SIIL_GPIO1 | SIIL_GPIO2 \
+			| SIIL_DDR | SIIL_LBC | SIIL_GTM2 | SIIL_GTM6 \
+			| SIIL_PMC |SIIL_GTM3 | SIIL_GTM7 | SIIL_GTM1 \
+			| SIIL_GTM5 |SIIL_DPTC )
+	u32    siprr_a; /*  System Internal Interrupt Group A Priority Register (PRR)  */
+	u8     res0[8];
+	u32    siprr_d; /*  System Internal Interrupt Group D Priority Register (PRR)  */
+	u32    simsr_h; /*  System Internal Interrupt Mask Register - High (SIIH)  */
+	u32    simsr_l; /*  System Internal Interrupt Mask Register - Low (SIIL)  */
+	u8     res1[4];
+	u32    sepnr;   /*  System External Interrupt Pending Register (SEI)  */
+	u32    smprr_a; /*  System Mixed Interrupt Group A Priority Register (PRR)  */
+	u32    smprr_b; /*  System Mixed Interrupt Group B Priority Register (PRR)  */
+#define PRR_0 0xe0000000 /* Priority Register, Position 0 programming */
+#define PRR_1 0x1c000000 /* Priority Register, Position 1 programming */
+#define PRR_2 0x03800000 /* Priority Register, Position 2 programming */
+#define PRR_3 0x00700000 /* Priority Register, Position 3 programming */
+#define PRR_4 0x0000e000 /* Priority Register, Position 4 programming */
+#define PRR_5 0x00001c00 /* Priority Register, Position 5 programming */
+#define PRR_6 0x00000380 /* Priority Register, Position 6 programming */
+#define PRR_7 0x00000070 /* Priority Register, Position 7 programming */
+#define PRR_RES ~(PRR_0|PRR_1|PRR_2|PRR_3|PRR_4|PRR_5|PRR_6|PRR_7)
+	u32    semsr; /*  System External Interrupt Mask Register (SEI)  */
+#define SEI_IRQ0  0x80000000 /*  IRQ0 external interrupt  */
+#define SEI_IRQ1  0x40000000 /*  IRQ1 external interrupt  */
+#define SEI_IRQ2  0x20000000 /*  IRQ2 external interrupt  */
+#define SEI_IRQ3  0x10000000 /*  IRQ3 external interrupt  */
+#define SEI_IRQ4  0x08000000 /*  IRQ4 external interrupt  */
+#define SEI_IRQ5  0x04000000 /*  IRQ5 external interrupt  */
+#define SEI_IRQ6  0x02000000 /*  IRQ6 external interrupt  */
+#define SEI_IRQ7  0x01000000 /*  IRQ7 external interrupt  */
+#define SEI_SIRQ0 0x00008000 /*  SIRQ0 external interrupt  */
+#define SEI_RES		~( SEI_IRQ0 | SEI_IRQ1 | SEI_IRQ2 | SEI_IRQ3 \
+			| SEI_IRQ4 | SEI_IRQ5 | SEI_IRQ6 | SEI_IRQ7 \
+			| SEI_SIRQ0)
+	u32    secnr; /*  System External Interrupt Control Register (SECNR) */
+#define SECNR_MIXB0T 0xc0000000 /*  MIXB0 priority position IPIC output interrupt type  */
+#define SECNR_MIXB1T 0x30000000 /*  MIXB1 priority position IPIC output interrupt type  */
+#define SECNR_MIXA0T 0x00c00000 /*  MIXA0 priority position IPIC output interrupt type  */
+#define SECNR_SYSA1T 0x00300000 /*  MIXA1 priority position IPIC output interrupt type  */
+#define SECNR_EDI0   0x00008000 /*  IRQ0 external interrupt edge/level detect  */
+#define SECNR_EDI1   0x00004000 /*  IRQ1 external interrupt edge/level detect  */
+#define SECNR_EDI2   0x00002000 /*  IRQ2 external interrupt edge/level detect  */
+#define SECNR_EDI3   0x00001000 /*  IRQ3 external interrupt edge/level detect  */
+#define SECNR_EDI4   0x00000800 /*  IRQ4 external interrupt edge/level detect  */
+#define SECNR_EDI5   0x00000400 /*  IRQ5 external interrupt edge/level detect  */
+#define SECNR_EDI6   0x00000200 /*  IRQ6 external interrupt edge/level detect  */
+#define SECNR_EDI7   0x00000100 /*  IRQ7 external interrupt edge/level detect  */
+#define SECNR_RES	~( SECNR_MIXB0T | SECNR_MIXB1T | SECNR_MIXA0T \
+			| SECNR_SYSA1T | SECNR_EDI0 | SECNR_EDI1 \
+			| SECNR_EDI2 | SECNR_EDI3 | SECNR_EDI4 \
+			| SECNR_EDI5 | SECNR_EDI6 | SECNR_EDI7)
+	u32   sersr; /*  System Error Status Register (SERR)  */
+	u32   sermr; /*  System Error Mask Register (SERR)  */
+#define SERR_IRQ0 0x80000000 /*  IRQ0 MCP request  */
+#define SERR_WDT  0x40000000 /*  WDT MCP request  */
+#define SERR_SBA  0x20000000 /*  SBA MCP request  */
+#define SERR_DDR  0x10000000 /*  DDR MCP request  */
+#define SERR_LBC  0x08000000 /*  LBC MCP request  */
+#define SERR_PCI1 0x04000000 /*  PCI1 MCP request  */
+#define SERR_PCI2 0x02000000 /*  PCI2 MCP request  */
+#define SERR_MU   0x01000000 /*  MU MCP request  */
+#define SERR_RNC  0x00010000 /*  MU MCP request (!!! Non-visible for users !!!)  */
+#define SERR_RES	~( SERR_IRQ0 | SERR_WDT | SERR_SBA | SERR_DDR \
+			|SERR_LBC | SERR_PCI1 | SERR_PCI2 | SERR_MU \
+			|SERR_RNC )
+	u32    sercr; /*  System Error Control Register  (SERCR)  */
+#define SERCR_MCPR 0x00000001 /*  MCP Route  */
+#define SERCR_RES ~(SERCR_MCPR)
+	u8    res2[4];
+	u32   sifcr_h; /*  System Internal Interrupt Force Register - High (SIIH)  */
+	u32   sifcr_l; /*  System Internal Interrupt Force Register - Low (SIIL)  */
+	u32   sefcr;   /*  System External Interrupt Force Register (SEI)  */
+	u32   serfr;   /*  System Error Force Register (SERR)  */
+	u8    res3[0xA0];
+} ipic8349_t;
+
+/*
+ * System Arbiter Registers
+ */
+typedef struct arbiter8349 {
+	u32 acr; /* Arbiter Configuration Register */
+#define ACR_COREDIS    0x10000000 /* Core disable. */
+#define ACR_PIPE_DEP   0x00070000 /* Pipeline depth (number of outstanding transactions). */
+#define ACR_PCI_RPTCNT 0x00007000 /* PCI repeat count. */
+#define ACR_RPTCNT     0x00000700 /* Repeat count. */
+#define ACR_APARK      0x00000030 /* Address parking. */
+#define ACR_PARKM	   0x0000000F /* Parking master. */
+#define ACR_RES ~(ACR_COREDIS|ACR_PIPE_DEP|ACR_PCI_RPTCNT|ACR_RPTCNT|ACR_APARK|ACR_PARKM)
+	u32 atr; /* Arbiter Timers Register */
+#define ATR_DTO 0x00FF0000 /* Data time out. */
+#define ATR_ATO	0x000000FF /* Address time out. */
+#define ATR_RES ~(ATR_DTO|ATR_ATO)
+	u8 res[4];
+	u32 aer; /* Arbiter Event Register (AE)*/
+	u32 aidr; /* Arbiter Interrupt Definition Register (AE) */
+	u32 amr; /* Arbiter Mask Register (AE) */
+	u32 aeatr; /* Arbiter Event Attributes Register */
+#define AEATR_EVENT   0x07000000 /* Event type. */
+#define AEATR_MSTR_ID 0x001F0000 /* Master Id. */
+#define AEATR_TBST    0x00000800 /* Transfer burst. */
+#define AEATR_TSIZE   0x00000700 /* Transfer Size. */
+#define AEATR_TTYPE	  0x0000001F /* Transfer Type. */
+#define AEATR_RES ~(AEATR_EVENT|AEATR_MSTR_ID|AEATR_TBST|AEATR_TSIZE|AEATR_TTYPE)
+	u32 aeadr; /* Arbiter Event Address Register */
+	u32 aerr; /* Arbiter Event Response Register (AE)*/
+#define AE_ETEA 0x00000020 /* Transfer error. */
+#define AE_RES_ 0x00000010 /* Reserved transfer type. */
+#define AE_ECW  0x00000008 /* External control word transfer type. */
+#define AE_AO   0x00000004 /* Address Only transfer type. */
+#define AE_DTO  0x00000002 /* Data time out. */
+#define AE_ATO	0x00000001 /* Address time out. */
+#define AE_RSRV ~(AE_ETEA|AE_RES_|AE_ECW|AE_AO|AE_DTO|AE_ATO)
+	u8 res1[0xDC];
+} arbiter8349_t;
+
+/*
+ * Reset Module
+ */
+typedef struct reset8349 {
+	u32    rcwl; /* RCWL Register  */
+#define RCWL_LBIUCM  0x80000000 /* LBIUCM  */
+#define RCWL_LBIUCM_SHIFT    31
+#define RCWL_DDRCM   0x40000000 /* DDRCM  */
+#define RCWL_DDRCM_SHIFT     30
+#define RCWL_SVCOD   0x30000000 /* SVCOD  */
+#define RCWL_SPMF    0x0f000000 /* SPMF  */
+#define RCWL_SPMF_SHIFT      24
+#define RCWL_COREPLL 0x007F0000 /* COREPLL  */
+#define RCWL_COREPLL_SHIFT   16
+#define RCWL_CEVCOD  0x000000C0 /* CEVCOD  */
+#define RCWL_CEPDF   0x00000020 /* CEPDF  */
+#define RCWL_CEPMF   0x0000001F /* CEPMF  */
+#define RCWL_RES ~(RCWL_BIUCM|RCWL_DDRCM|RCWL_SVCOD|RCWL_SPMF|RCWL_COREPLL|RCWL_CEVCOD|RCWL_CEPDF|RCWL_CEPMF)
+	u32    rcwh; /* RCHL Register  */
+#define RCWH_PCIHOST 0x80000000 /* PCIHOST  */
+#define RCWH_PCIHOST_SHIFT   31
+#define RCWH_PCI64   0x40000000 /* PCI64  */
+#define RCWH_PCI1ARB 0x20000000 /* PCI1ARB  */
+#define RCWH_PCI2ARB 0x10000000 /* PCI2ARB  */
+#define RCWH_COREDIS 0x08000000 /* COREDIS  */
+#define RCWH_BMS     0x04000000 /* BMS  */
+#define RCWH_BOOTSEQ 0x03000000 /* BOOTSEQ  */
+#define RCWH_SWEN    0x00800000 /* SWEN  */
+#define RCWH_ROMLOC  0x00700000 /* ROMLOC  */
+#define RCWH_TSEC1M  0x0000c000 /* TSEC1M  */
+#define RCWH_TSEC2M  0x00003000 /* TSEC2M  */
+#define RCWH_TPR     0x00000100 /* TPR  */
+#define RCWH_TLE     0x00000008 /* TLE  */
+#define RCWH_LALE    0x00000004 /* LALE  */
+#define RCWH_RES	~(RCWH_PCIHOST | RCWH_PCI64 | RCWH_PCI1ARB \
+			| RCWH_PCI2ARB | RCWH_COREDIS | RCWH_BMS \
+			| RCWH_BOOTSEQ | RCWH_SWEN | RCWH_ROMLOC \
+			| RCWH_TSEC1M | RCWH_TSEC2M | RCWH_TPR \
+			| RCWH_TLE | RCWH_LALE)
+	u8     res0[8];
+	u32    rsr; /* Reset status Register  */
+#define RSR_RSTSRC 0xE0000000 /* Reset source  */
+#define RSR_RSTSRC_SHIFT   29
+#define RSR_BSF    0x00010000 /* Boot seq. fail  */
+#define RSR_BSF_SHIFT      16
+#define RSR_SWSR   0x00002000 /* software soft reset  */
+#define RSR_SWSR_SHIFT     13
+#define RSR_SWHR   0x00001000 /* software hard reset  */
+#define RSR_SWHR_SHIFT     12
+#define RSR_JHRS   0x00000200 /* jtag hreset  */
+#define RSR_JHRS_SHIFT      9
+#define RSR_JSRS   0x00000100 /* jtag sreset status  */
+#define RSR_JSRS_SHIFT      8
+#define RSR_CSHR   0x00000010 /* checkstop reset status  */
+#define RSR_CSHR_SHIFT      4
+#define RSR_SWRS   0x00000008 /* software watchdog reset status  */
+#define RSR_SWRS_SHIFT      3
+#define RSR_BMRS   0x00000004 /* bus monitop reset status  */
+#define RSR_BMRS_SHIFT      2
+#define RSR_SRS    0x00000002 /* soft reset status  */
+#define RSR_SRS_SHIFT       1
+#define RSR_HRS    0x00000001 /* hard reset status  */
+#define RSR_HRS_SHIFT       0
+#define RSR_RES ~(RSR_RSTSRC | RSR_BSF | RSR_SWSR | RSR_SWHR | RSR_JHRS | RSR_JSRS | RSR_CSHR | RSR_SWRS | RSR_BMRS | RSR_SRS | RSR_HRS)
+	u32    rmr; /* Reset mode Register  */
+#define RMR_CSRE   0x00000001 /* checkstop reset enable  */
+#define RMR_CSRE_SHIFT      0
+#define RMR_RES ~(RMR_CSRE)
+	u32    rpr; /* Reset protection Register  */
+	u32    rcr; /* Reset Control Register  */
+#define RCR_SWHR 0x00000002 /* software hard reset  */
+#define RCR_SWSR 0x00000001 /* software soft reset  */
+#define RCR_RES ~(RCR_SWHR | RCR_SWSR)
+	u32    rcer; /* Reset Control Enable Register  */
+#define RCER_CRE 0x00000001 /* software hard reset  */
+#define RCER_RES ~(RCER_CRE)
+	u8     res1[0xDC];
+} reset8349_t;
+
+typedef struct clk8349 {
+	u32    spmr; /* system PLL mode Register  */
+#define SPMR_LBIUCM  0x80000000 /* LBIUCM  */
+#define SPMR_DDRCM   0x40000000 /* DDRCM  */
+#define SPMR_SVCOD   0x30000000 /* SVCOD  */
+#define SPMR_SPMF    0x0F000000 /* SPMF  */
+#define SPMR_CKID    0x00800000 /* CKID  */
+#define SPMR_CKID_SHIFT 23
+#define SPMR_COREPLL 0x007F0000 /* COREPLL  */
+#define SPMR_CEVCOD  0x000000C0 /* CEVCOD  */
+#define SPMR_CEPDF   0x00000020 /* CEPDF  */
+#define SPMR_CEPMF   0x0000001F /* CEPMF  */
+#define SPMR_RES	~(SPMR_LBIUCM | SPMR_DDRCM | SPMR_SVCOD \
+			| SPMR_SPMF | SPMR_CKID | SPMR_COREPLL \
+			| SPMR_CEVCOD | SPMR_CEPDF | SPMR_CEPMF)
+	u32    occr; /* output clock control Register  */
+#define OCCR_PCICOE0 0x80000000 /* PCICOE0  */
+#define OCCR_PCICOE1 0x40000000 /* PCICOE1  */
+#define OCCR_PCICOE2 0x20000000 /* PCICOE2  */
+#define OCCR_PCICOE3 0x10000000 /* PCICOE3  */
+#define OCCR_PCICOE4 0x08000000 /* PCICOE4  */
+#define OCCR_PCICOE5 0x04000000 /* PCICOE5  */
+#define OCCR_PCICOE6 0x02000000 /* PCICOE6  */
+#define OCCR_PCICOE7 0x01000000 /* PCICOE7  */
+#define OCCR_PCICD0  0x00800000 /* PCICD0  */
+#define OCCR_PCICD1  0x00400000 /* PCICD1  */
+#define OCCR_PCICD2  0x00200000 /* PCICD2  */
+#define OCCR_PCICD3  0x00100000 /* PCICD3  */
+#define OCCR_PCICD4  0x00080000 /* PCICD4  */
+#define OCCR_PCICD5  0x00040000 /* PCICD5  */
+#define OCCR_PCICD6  0x00020000 /* PCICD6  */
+#define OCCR_PCICD7  0x00010000 /* PCICD7  */
+#define OCCR_PCI1CR  0x00000002 /* PCI1CR  */
+#define OCCR_PCI2CR  0x00000001 /* PCI2CR  */
+#define OCCR_RES	~(OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2 \
+			| OCCR_PCICOE3 | OCCR_PCICOE4 | OCCR_PCICOE5 \
+			| OCCR_PCICOE6 | OCCR_PCICOE7 | OCCR_PCICD0 \
+			| OCCR_PCICD1 | OCCR_PCICD2  | OCCR_PCICD3 \
+			| OCCR_PCICD4  | OCCR_PCICD5 | OCCR_PCICD6  \
+			| OCCR_PCICD7  | OCCR_PCI1CR  | OCCR_PCI2CR )
+	u32    sccr; /* system clock control Register  */
+#define SCCR_TSEC1CM  0xc0000000 /* TSEC1CM  */
+#define SCCR_TSEC1CM_SHIFT 30
+#define SCCR_TSEC2CM  0x30000000 /* TSEC2CM  */
+#define SCCR_TSEC2CM_SHIFT 28
+#define SCCR_ENCCM    0x03000000 /* ENCCM  */
+#define SCCR_ENCCM_SHIFT 24
+#define SCCR_USBMPHCM 0x00c00000 /* USBMPHCM  */
+#define SCCR_USBMPHCM_SHIFT 22
+#define SCCR_USBDRCM  0x00300000 /* USBDRCM  */
+#define SCCR_USBDRCM_SHIFT 20
+#define SCCR_PCICM    0x00010000 /* PCICM  */
+#define SCCR_RES	~( SCCR_TSEC1CM | SCCR_TSEC2CM | SCCR_ENCCM \
+			| SCCR_USBMPHCM | SCCR_USBDRCM | SCCR_PCICM)
+	u8     res0[0xF4];
+} clk8349_t;
+
+/*
+ * Power Management Control Module
+ */
+typedef struct pmc8349 {
+	u32    pmccr; /* PMC Configuration Register  */
+#define PMCCR_SLPEN 0x00000001 /* System Low Power Enable  */
+#define PMCCR_DLPEN 0x00000002 /* DDR SDRAM Low Power Enable  */
+#define PMCCR_RES ~(PMCCR_SLPEN | PMCCR_DLPEN)
+	u32    pmcer; /* PMC Event Register  */
+#define PMCER_PMCI  0x00000001 /* PMC Interrupt  */
+#define PMCER_RES ~(PMCER_PMCI)
+	u32    pmcmr; /* PMC Mask Register  */
+#define PMCMR_PMCIE 0x0001 /* PMC Interrupt Enable  */
+#define PMCMR_RES ~(PMCMR_PMCIE)
+	u8 res0[0xF4];
+} pmc8349_t;
+
+
+/*
+ * general purpose I/O module
+ */
+typedef struct gpio8349 {
+	u32 dir; /* direction register */
+	u32 odr; /* open drain register */
+	u32 dat; /* data register */
+	u32 ier; /* interrupt event register */
+	u32 imr; /* interrupt mask register */
+	u32 icr; /* external interrupt control register */
+	u8 res0[0xE8];
+} gpio8349_t;
+
+/*
+ * DDR Memory Controller Memory Map
+ */
+typedef struct ddr_cs_bnds{
+	u32 csbnds;
+#define CSBNDS_SA 0x00FF0000
+#define CSBNDS_SA_SHIFT   16
+#define CSBNDS_EA 0x000000FF
+#define CSBNDS_EA_SHIFT    0
+	u8  res0[4];
+} ddr_cs_bnds_t;
+
+typedef struct ddr8349{
+	ddr_cs_bnds_t csbnds[4];            /**< Chip Select x Memory Bounds */
+	u8 res0[0x60];
+	u32 cs_config[4];       /**< Chip Select x Configuration */
+#define CSCONFIG_EN         0x80000000
+#define CSCONFIG_AP         0x00800000
+#define CSCONFIG_ROW_BIT    0x00000700
+#define CSCONFIG_ROW_BIT_12 0x00000000
+#define CSCONFIG_ROW_BIT_13 0x00000100
+#define CSCONFIG_ROW_BIT_14 0x00000200
+#define CSCONFIG_COL_BIT    0x00000007
+#define CSCONFIG_COL_BIT_8  0x00000000
+#define CSCONFIG_COL_BIT_9  0x00000001
+#define CSCONFIG_COL_BIT_10 0x00000002
+#define CSCONFIG_COL_BIT_11 0x00000003
+	u8 res1[0x78];
+	u32 timing_cfg_1;       /**< SDRAM Timing Configuration 1 */
+#define TIMING_CFG1_PRETOACT 0x70000000
+#define TIMING_CFG1_PRETOACT_SHIFT   28
+#define TIMING_CFG1_ACTTOPRE 0x0F000000
+#define TIMING_CFG1_ACTTOPRE_SHIFT   24
+#define TIMING_CFG1_ACTTORW  0x00700000
+#define TIMING_CFG1_ACTTORW_SHIFT    20
+#define TIMING_CFG1_CASLAT   0x00070000
+#define TIMING_CFG1_CASLAT_SHIFT     16
+#define TIMING_CFG1_REFREC   0x0000F000
+#define TIMING_CFG1_REFREC_SHIFT     12
+#define TIMING_CFG1_WRREC    0x00000700
+#define TIMING_CFG1_WRREC_SHIFT       8
+#define TIMING_CFG1_ACTTOACT 0x00000070
+#define TIMING_CFG1_ACTTOACT_SHIFT    4
+#define TIMING_CFG1_WRTORD   0x00000007
+#define TIMING_CFG1_WRTORD_SHIFT      0
+
+	u32 timing_cfg_2;       /**< SDRAM Timing Configuration 2 */
+#define TIMING_CFG2_CPO           0x0F000000
+#define TIMING_CFG2_CPO_SHIFT             24
+#define TIMING_CFG2_ACSM          0x00080000
+#define TIMING_CFG2_WR_DATA_DELAY 0x00001C00
+#define TIMING_CFG2_WR_DATA_DELAY_SHIFT   10
+
+	u32 sdram_cfg;          /**< SDRAM Control Configuration */
+#define SDRAM_CFG_MEM_EN     0x80000000
+#define SDRAM_CFG_SREN       0x40000000
+#define SDRAM_CFG_ECC_EN     0x20000000
+#define SDRAM_CFG_RD_EN      0x10000000
+#define SDRAM_CFG_SDRAM_TYPE 0x03000000
+#define SDRAM_CFG_SDRAM_TYPE_SHIFT   24
+#define SDRAM_CFG_DYN_PWR    0x00200000
+#define SDRAM_CFG_32_BE      0x00080000
+#define SDRAM_CFG_8_BE       0x00040000
+#define SDRAM_CFG_NCAP       0x00020000
+#define SDRAM_CFG_2T_EN      0x00008000
+
+	u8 res2[4];
+	u32 sdram_mode;         /**< SDRAM Mode Configuration */
+#define SDRAM_MODE_ESD 0xFFFF0000
+#define SDRAM_MODE_ESD_SHIFT   16
+#define SDRAM_MODE_SD  0x0000FFFF
+#define SDRAM_MODE_SD_SHIFT     0
+
+	u8 res3[8];
+	u32 sdram_interval;     /**< SDRAM Interval Configuration */
+#define SDRAM_INTERVAL_REFINT  0x3FFF0000
+#define SDRAM_INTERVAL_REFINT_SHIFT    16
+#define SDRAM_INTERVAL_BSTOPRE 0x00003FFF
+#define SDRAM_INTERVAL_BSTOPRE_SHIFT    0
+	u8   res9[8];
+	u32  sdram_clk_cntl;
+	u8 res4[0xCCC];
+	u32 data_err_inject_hi; /**< Memory Data Path Error Injection Mask High */
+	u32 data_err_inject_lo; /**< Memory Data Path Error Injection Mask Low */
+	u32 ecc_err_inject;     /**< Memory Data Path Error Injection Mask ECC */
+	u8 res5[0x14];
+	u32 capture_data_hi;    /**< Memory Data Path Read Capture High */
+	u32 capture_data_lo;    /**< Memory Data Path Read Capture Low */
+	u32 capture_ecc;        /**< Memory Data Path Read Capture ECC */
+	u8 res6[0x14];
+	u32 err_detect;         /**< Memory Error Detect */
+	u32 err_disable;        /**< Memory Error Disable */
+	u32 err_int_en;         /**< Memory Error Interrupt Enable */
+	u32 capture_attributes; /**< Memory Error Attributes Capture */
+	u32 capture_address;    /**< Memory Error Address Capture */
+	u32 capture_ext_address;/**< Memory Error Extended Address Capture */
+	u32 err_sbe;            /**< Memory Single-Bit ECC Error Management */
+	u8 res7[0xA4];
+	u32 debug_reg;
+	u8 res8[0xFC];
+} ddr8349_t;
+
+/*
+ * I2C1 Controller
+ */
+
+
+/*
+ * DUART
+ */
+typedef struct duart8349{
+	u8 urbr_ulcr_udlb; /**< combined register for URBR, UTHR and UDLB */
+	u8 uier_udmb;      /**< combined register for UIER and UDMB */
+	u8 uiir_ufcr_uafr; /**< combined register for UIIR, UFCR and UAFR */
+	u8 ulcr;        /**< line control register */
+	u8 umcr;        /**< MODEM control register */
+	u8 ulsr;        /**< line status register */
+	u8 umsr;        /**< MODEM status register */
+	u8 uscr;        /**< scratch register */
+	u8 res0[8];
+	u8 udsr;        /**< DMA status register */
+	u8 res1[3];
+	u8 res2[0xEC];
+} duart8349_t;
+
+/*
+ * Local Bus Controller Registers
+ */
+typedef struct lbus_bank{
+	u32 br;             /**< Base Register  */
+	u32 or;             /**< Base Register  */
+} lbus_bank_t;
+
+typedef struct lbus8349 {
+	lbus_bank_t bank[8];
+	u8 res0[0x28];
+	u32 mar;                /**< UPM Address Register */
+	u8 res1[0x4];
+	u32 mamr;               /**< UPMA Mode Register */
+	u32 mbmr;               /**< UPMB Mode Register */
+	u32 mcmr;               /**< UPMC Mode Register */
+	u8 res2[0x8];
+	u32 mrtpr;              /**< Memory Refresh Timer Prescaler Register */
+	u32 mdr;                /**< UPM Data Register */
+	u8 res3[0x8];
+	u32 lsdmr;              /**< SDRAM Mode Register */
+	u8 res4[0x8];
+	u32 lurt;               /**< UPM Refresh Timer */
+	u32 lsrt;               /**< SDRAM Refresh Timer */
+	u8 res5[0x8];
+	u32 ltesr;              /**< Transfer Error Status Register */
+	u32 ltedr;              /**< Transfer Error Disable Register */
+	u32 lteir;              /**< Transfer Error Interrupt Register */
+	u32 lteatr;             /**< Transfer Error Attributes Register */
+	u32 ltear;              /**< Transfer Error Address Register */
+	u8 res6[0xC];
+	u32 lbcr;               /**< Configuration Register */
+#define LBCR_LDIS  0x80000000
+#define LBCR_LDIS_SHIFT    31
+#define LBCR_BCTLC 0x00C00000
+#define LBCR_BCTLC_SHIFT   22
+#define LBCR_LPBSE 0x00020000
+#define LBCR_LPBSE_SHIFT   17
+#define LBCR_EPAR  0x00010000
+#define LBCR_EPAR_SHIFT    16
+#define LBCR_BMT   0x0000FF00
+#define LBCR_BMT_SHIFT      8
+	u32 lcrr;               /**< Clock Ratio Register */
+#define LCRR_DBYP    0x80000000
+#define LCRR_DBYP_SHIFT      31
+#define LCRR_BUFCMDC 0x30000000
+#define LCRR_BUFCMDC_SHIFT   28
+#define LCRR_ECL     0x03000000
+#define LCRR_ECL_SHIFT       24
+#define LCRR_EADC    0x00030000
+#define LCRR_EADC_SHIFT      16
+#define LCRR_CLKDIV  0x0000000F
+#define LCRR_CLKDIV_SHIFT     0
+
+
+	u8 res7[0x28];
+	u8 res8[0xF00];
+} lbus8349_t;
+
+/*
+ * Serial Peripheral Interface
+ */
+typedef struct spi8349
+{
+	u32 mode;     /**< mode register  */
+	u32 event;    /**< event register */
+	u32 mask;     /**< mask register  */
+	u32 com;      /**< command register */
+	u8 res0[0x10];
+	u32 tx;       /**< transmit register */
+	u32 rx;       /**< receive register */
+	u8 res1[0xD8];
+} spi8349_t;
+
+typedef struct dma8349 {
+	u8 fixme[0x300];
+} dma8349_t;
+
+/*
+ * PCI Software Configuration Registers
+ */
+typedef struct pciconf8349 {
+	u32	config_address;
+#define PCI_CONFIG_ADDRESS_EN	0x80000000
+#define PCI_CONFIG_ADDRESS_BN_SHIFT	16
+#define PCI_CONFIG_ADDRESS_BN_MASK	0x00ff0000
+#define PCI_CONFIG_ADDRESS_DN_SHIFT	11
+#define PCI_CONFIG_ADDRESS_DN_MASK	0x0000f800
+#define PCI_CONFIG_ADDRESS_FN_SHIFT	8
+#define PCI_CONFIG_ADDRESS_FN_MASK	0x00000700
+#define PCI_CONFIG_ADDRESS_RN_SHIFT	0
+#define PCI_CONFIG_ADDRESS_RN_MASK	0x000000fc
+	u32 config_data;
+	u32 int_ack;
+	u8	res[116];
+} pciconf8349_t;
+
+/*
+ * PCI Outbound Translation Register
+ */
+typedef struct pci_outbound_window {
+	u32	potar;
+	u8	res0[4];
+	u32	pobar;
+	u8	res1[4];
+	u32	pocmr;
+	u8	res2[4];
+} pot8349_t;
+/*
+ * Sequencer
+ */
+typedef struct ios8349 {
+	pot8349_t	pot[6];
+#define POTAR_TA_MASK	0x000fffff
+#define	POBAR_BA_MASK	0x000fffff
+#define	POCMR_EN	0x80000000
+#define	POCMR_IO	0x40000000	/* 0--memory space 1--I/O space */
+#define	POCMR_SE	0x20000000	/* streaming enable */
+#define	POCMR_DST	0x10000000	/* 0--PCI1 1--PCI2*/
+#define	POCMR_CM_MASK	0x000fffff
+#define	POCMR_CM_4G	0x00000000
+#define	POCMR_CM_2G	0x00080000
+#define	POCMR_CM_1G	0x000C0000
+#define	POCMR_CM_512M	0x000E0000
+#define	POCMR_CM_256M	0x000F0000
+#define	POCMR_CM_128M	0x000F8000
+#define	POCMR_CM_64M	0x000FC000
+#define	POCMR_CM_32M	0x000FE000
+#define	POCMR_CM_16M	0x000FF000
+#define	POCMR_CM_8M	0x000FF800
+#define	POCMR_CM_4M	0x000FFC00
+#define	POCMR_CM_2M	0x000FFE00
+#define	POCMR_CM_1M	0x000FFF00
+#define	POCMR_CM_512K	0x000FFF80
+#define	POCMR_CM_256K	0x000FFFC0
+#define	POCMR_CM_128K	0x000FFFE0
+#define	POCMR_CM_64K	0x000FFFF0
+#define	POCMR_CM_32K	0x000FFFF8
+#define	POCMR_CM_16K	0x000FFFFC
+#define	POCMR_CM_8K	0x000FFFFE
+#define	POCMR_CM_4K	0x000FFFFF
+	u8	res0[0x60];
+	u32	pmcr;
+	u8	res1[4];
+	u32	dtcr;
+	u8	res2[4];
+} ios8349_t;
+
+/*
+ * PCI Controller Control and Status Registers
+ */
+typedef struct pcictrl8349 {
+	u32	esr;
+#define ESR_MERR	0x80000000
+#define ESR_APAR	0x00000400
+#define	ESR_PCISERR	0x00000200
+#define	ESR_MPERR	0x00000100
+#define	ESR_TPERR	0x00000080
+#define	ESR_NORSP	0x00000040
+#define	ESR_TABT	0x00000020
+	u32	ecdr;
+#define ECDR_APAR	0x00000400
+#define	ECDR_PCISERR	0x00000200
+#define	ECDR_MPERR	0x00000100
+#define	ECDR_TPERR	0x00000080
+#define	ECDR_NORSP	0x00000040
+#define	ECDR_TABT	0x00000020
+	u32 eer;
+#define EER_APAR	0x00000400
+#define	EER_PCISERR	0x00000200
+#define	EER_MPERR	0x00000100
+#define	EER_TPERR	0x00000080
+#define	EER_NORSP	0x00000040
+#define	EER_TABT	0x00000020
+	u32	eatcr;
+#define	EATCR_ERRTYPR_MASK	0x70000000
+#define	EATCR_ERRTYPR_APR	0x00000000	/* address parity error */
+#define	EATCR_ERRTYPR_WDPR	0x10000000	/* write data parity error */
+#define	EATCR_ERRTYPR_RDPR	0x20000000	/* read data parity error */
+#define	EATCR_ERRTYPR_MA	0x30000000	/* master abort */
+#define	EATCR_ERRTYPR_TA	0x40000000	/* target abort */
+#define	EATCR_ERRTYPR_SE	0x50000000	/* system error indication received */
+#define	EATCR_ERRTYPR_PEA	0x60000000	/* parity error indication received on a read */
+#define	EATCR_ERRTYPR_PEW	0x70000000	/* parity error indication received on a write */
+#define EATCR_BN_MASK		0x0f000000	/* beat number */
+#define	EATCR_BN_1st		0x00000000
+#define	EATCR_BN_2ed		0x01000000
+#define	EATCR_BN_3rd		0x02000000
+#define	EATCR_BN_4th		0x03000000
+#define	EATCR_BN_5th		0x0400000
+#define	EATCR_BN_6th		0x05000000
+#define	EATCR_BN_7th		0x06000000
+#define	EATCR_BN_8th		0x07000000
+#define	EATCR_BN_9th		0x08000000
+#define EATCR_TS_MASK		0x00300000	/* transaction size */
+#define	EATCR_TS_4		0x00000000
+#define	EATCR_TS_1		0x00100000
+#define	EATCR_TS_2		0x00200000
+#define	EATCR_TS_3		0x00300000
+#define	EATCR_ES_MASK		0x000f0000	/* error source */
+#define	EATCR_ES_EM		0x00000000	/* external master */
+#define	EATCR_ES_DMA		0x00050000
+#define	EATCR_CMD_MASK		0x0000f000
+#define	EATCR_HBE_MASK		0x00000f00	/* PCI high byte enable*/
+#define	EATCR_BE_MASK		0x000000f0	/* PCI byte enable */
+#define	EATCR_HPB		0x00000004	/* high parity bit */
+#define	EATCR_PB		0x00000002	/* parity bit*/
+#define	EATCR_VI		0x00000001	/* error information valid */
+	u32	eacr;
+	u32	eeacr;
+	u32	edlcr;
+	u32	edhcr;
+	u32	gcr;
+	u32	ecr;
+	u32	gsr;
+	u8	res0[12];
+	u32	pitar2;
+	u8	res1[4];
+	u32	pibar2;
+	u32	piebar2;
+	u32	piwar2;
+	u8	res2[4];
+	u32	pitar1;
+	u8	res3[4];
+	u32	pibar1;
+	u32	piebar1;
+	u32	piwar1;
+	u8	res4[4];
+	u32	pitar0;
+	u8	res5[4];
+	u32	pibar0;
+	u8	res6[4];
+	u32	piwar0;
+	u8	res7[132];
+#define PITAR_TA_MASK		0x000fffff
+#define PIBAR_MASK		0xffffffff
+#define PIEBAR_EBA_MASK		0x000fffff
+#define PIWAR_EN		0x80000000
+#define PIWAR_PF		0x20000000
+#define	PIWAR_RTT_MASK		0x000f0000
+#define	PIWAR_RTT_NO_SNOOP	0x00040000
+#define PIWAR_RTT_SNOOP		0x00050000
+#define	PIWAR_WTT_MASK		0x0000f000
+#define	PIWAR_WTT_NO_SNOOP	0x00004000
+#define PIWAR_WTT_SNOOP		0x00005000
+#define	PIWAR_IWS_MASK	0x0000003F
+#define	PIWAR_IWS_4K	0x0000000B
+#define	PIWAR_IWS_8K	0x0000000C
+#define	PIWAR_IWS_16K	0x0000000D
+#define	PIWAR_IWS_32K	0x0000000E
+#define	PIWAR_IWS_64K	0x0000000F
+#define	PIWAR_IWS_128K	0x00000010
+#define	PIWAR_IWS_256K	0x00000011
+#define	PIWAR_IWS_512K	0x00000012
+#define	PIWAR_IWS_1M	0x00000013
+#define	PIWAR_IWS_2M	0x00000014
+#define	PIWAR_IWS_4M	0x00000015
+#define	PIWAR_IWS_8M	0x00000016
+#define	PIWAR_IWS_16M	0x00000017
+#define	PIWAR_IWS_32M	0x00000018
+#define	PIWAR_IWS_64M	0x00000019
+#define	PIWAR_IWS_128M	0x0000001A
+#define	PIWAR_IWS_256M	0x0000001B
+#define	PIWAR_IWS_512M	0x0000001C
+#define	PIWAR_IWS_1G	0x0000001D
+#define	PIWAR_IWS_2G	0x0000001E
+} pcictrl8349_t;
+
+/*
+ * USB
+ */
+typedef struct usb8349 {
+	u8 fixme[0x2000];
+} usb8349_t;
+
+/*
+ * TSEC
+ */
+typedef struct tsec8349 {
+	u8 fixme[0x1000];
+} tsec8349_t;
+
+/*
+ * Security
+ */
+typedef struct security8349 {
+	u8 fixme[0x10000];
+} security8349_t;
+
+typedef struct immap {
+	sysconf8349_t sysconf; /* System configuration */
+	wdt8349_t     wdt;     /* Watch Dog Timer (WDT) Registers */
+	rtclk8349_t   rtc;     /* Real Time Clock Module Registers */
+	rtclk8349_t   pit;     /* Periodic Interval Timer */
+	gtm8349_t     gtm[2];  /* Global Timers Module */
+	ipic8349_t    ipic;    /* Integrated Programmable Interrupt Controller */
+	arbiter8349_t arbiter; /* System Arbiter Registers */
+	reset8349_t   reset;   /* Reset Module */
+	clk8349_t     clk;     /* System Clock Module */
+	pmc8349_t     pmc;     /* Power Management Control Module */
+	gpio8349_t    pgio[2]; /* general purpose I/O module */
+	u8 res0[0x200];
+	u8 DDL_DDR[0x100];
+	u8 DDL_LBIU[0x100];
+	u8 res1[0xE00];
+	ddr8349_t     ddr;     /* DDR Memory Controller Memory */
+	i2c_t     i2c[2];      /* I2C1 Controller */
+	u8 res2[0x1300];
+	duart8349_t   duart[2];/* DUART */
+	u8 res3[0x900];
+	lbus8349_t    lbus;    /* Local Bus Controller Registers */
+	u8 res4[0x1000];
+	spi8349_t     spi;     /* Serial Peripheral Interface */
+	u8 res5[0xF00];
+	dma8349_t     dma;     /* DMA */
+	pciconf8349_t pci_conf[2];  /* PCI Software Configuration Registers */
+	ios8349_t     ios;     /* Sequencer */
+	pcictrl8349_t pci_ctrl[2];  /* PCI Controller Control and Status Registers */
+	u8 res6[0x19900];
+	usb8349_t     usb;
+	tsec8349_t    tsec[2];
+	u8 res7[0xA000];
+	security8349_t security;
+} immap_t;
+
+#endif /* __IMMAP_8349__ */
diff --git a/include/asm-ppc/immap_85xx.h b/include/asm-ppc/immap_85xx.h
index 1b73defaa..2f10e9591 100644
--- a/include/asm-ppc/immap_85xx.h
+++ b/include/asm-ppc/immap_85xx.h
@@ -9,9 +9,9 @@
 #ifndef __IMMAP_85xx__
 #define __IMMAP_85xx__
 
-
-/* Local-Access Registers and ECM Registers(0x0000-0x2000) */
-
+/*
+ * Local-Access Registers and ECM Registers(0x0000-0x2000)
+ */
 typedef struct ccsr_local_ecm {
 	uint	ccsrbar;	/* 0x0 - Control Configuration Status Registers Base Address Register */
 	char	res1[4];
@@ -65,9 +65,9 @@ typedef struct ccsr_local_ecm {
 	char	res24[492];
 } ccsr_local_ecm_t;
 
-
-/* DDR memory controller registers(0x2000-0x3000) */
-
+/*
+ * DDR memory controller registers(0x2000-0x3000)
+ */
 typedef struct ccsr_ddr {
 	uint	cs0_bnds;		/* 0x2000 - DDR Chip Select 0 Memory Bounds */
 	char	res1[4];
@@ -81,21 +81,27 @@ typedef struct ccsr_ddr {
 	uint	cs1_config;		/* 0x2084 - DDR Chip Select Configuration */
 	uint	cs2_config;		/* 0x2088 - DDR Chip Select Configuration */
 	uint	cs3_config;		/* 0x208c - DDR Chip Select Configuration */
-	char	res5[120];
+	char	res5[112];
+	uint	ext_refrec;		/* 0x2100 - DDR SDRAM Extended Refresh Recovery */
+	uint	timing_cfg_0;		/* 0x2104 - DDR SDRAM Timing Configuration Register 0 */
 	uint	timing_cfg_1;		/* 0x2108 - DDR SDRAM Timing Configuration Register 1 */
 	uint	timing_cfg_2;		/* 0x210c - DDR SDRAM Timing Configuration Register 2 */
 	uint	sdram_cfg;		/* 0x2110 - DDR SDRAM Control Configuration */
-	char	res6[4];
+	uint	sdram_cfg_2;		/* 0x2114 - DDR SDRAM Control Configuration 2 */
 	uint	sdram_mode;		/* 0x2118 - DDR SDRAM Mode Configuration */
-	char	res7[8];
+	uint	sdram_mode_2;		/* 0x211c - DDR SDRAM Mode Configuration 2*/
+	uint	sdram_md_cntl;		/* 0x2120 - DDR SDRAM Mode Control */
 	uint	sdram_interval;		/* 0x2124 - DDR SDRAM Interval Configuration */
-#ifdef MPC85xx_DDR_SDRAM_CLK_CNTL
-	char	res7_5[8];
+	uint	sdram_data_init;	/* 0x2128 - DDR SDRAM Data initialization */
+	char	res6[4];
 	uint	sdram_clk_cntl;		/* 0x2130 - DDR SDRAM Clock Control */
-	char	res8[3276];
-#else
-	char	res8[3288];
-#endif
+	char	res7[20];
+	uint	init_address;		/* 0x2148 - DDR training initialization address */
+	uint	init_ext_address;	/* 0x214C - DDR training initialization extended address */
+	char	res8_1[2728];
+	uint	ip_rev1;		/* 0x2BF8 - DDR IP Block Revision 1 */
+	uint	ip_rev2;		/* 0x2BFC - DDR IP Block Revision 2 */
+	char	res8_2[512];
 	uint	data_err_inject_hi;	/* 0x2e00 - DDR Memory Data Path Error Injection Mask High */
 	uint	data_err_inject_lo;	/* 0x2e04 - DDR Memory Data Path Error Injection Mask Low */
 	uint	ecc_err_inject;		/* 0x2e08 - DDR Memory Data Path Error Injection Mask ECC */
@@ -119,9 +125,9 @@ typedef struct ccsr_ddr {
 	char	res12[240];
 } ccsr_ddr_t;
 
-
-/* I2C Registers(0x3000-0x4000) */
-
+/*
+ * I2C Registers(0x3000-0x4000)
+ */
 typedef struct ccsr_i2c {
 	u_char	i2cadr;		/* 0x3000 - I2C Address Register */
 #define MPC85xx_I2CADR_MASK	0xFE
@@ -158,6 +164,7 @@ typedef struct ccsr_i2c {
 
 #if defined(CONFIG_MPC8540) \
 	|| defined(CONFIG_MPC8541) \
+	|| defined(CONFIG_MPC8548) \
 	|| defined(CONFIG_MPC8555)
 /* DUART Registers(0x4000-0x5000) */
 typedef struct ccsr_duart {
@@ -237,10 +244,10 @@ typedef struct ccsr_lbc {
 	char	res8[12072];
 } ccsr_lbc_t;
 
-
-/* PCI Registers(0x8000-0x9000) */
-/* Omitting Reserved(0x9000-0x2_0000) */
-
+/*
+ * PCI Registers(0x8000-0x9000)
+ * Omitting Reserved(0x9000-0x2_0000)
+ */
 typedef struct ccsr_pcix {
 	uint	cfg_addr;	/* 0x8000 - PCIX Configuration Address Register */
 	uint	cfg_data;	/* 0x8004 - PCIX Configuration Data Register */
@@ -305,9 +312,9 @@ typedef struct ccsr_pcix {
 	char	res11[94688];
 } ccsr_pcix_t;
 
-
-/* L2 Cache Registers(0x2_0000-0x2_1000) */
-
+/*
+ * L2 Cache Registers(0x2_0000-0x2_1000)
+ */
 typedef struct ccsr_l2cache {
 	uint	l2ctl;		/* 0x20000 - L2 configuration register 0 */
 	char	res1[12];
@@ -349,9 +356,9 @@ typedef struct ccsr_l2cache {
 	char	res15[420];
 } ccsr_l2cache_t;
 
-
-/* DMA Registers(0x2_1000-0x2_2000) */
-
+/*
+ * DMA Registers(0x2_1000-0x2_2000)
+ */
 typedef struct ccsr_dma {
 	char	res1[256];
 	uint	mr0;		/* 0x21100 - DMA 0 Mode Register */
@@ -430,7 +437,9 @@ typedef struct ccsr_dma {
 	char	res22[11516];
 } ccsr_dma_t;
 
-/* tsec1 tsec2: 24000-26000 */
+/*
+ * tsec1 tsec2: 24000-26000
+ */
 typedef struct ccsr_tsec {
 	char	res1[16];
 	uint	ievent;		/* 0x24010 - Interrupt Event Register */
@@ -717,8 +726,9 @@ typedef struct ccsr_tsec {
 	char	res74[1024];
 } ccsr_tsec_t;
 
-/* PIC Registers(0x2_6000-0x4_0000-0x8_0000) */
-
+/*
+ * PIC Registers(0x2_6000-0x4_0000-0x8_0000)
+ */
 typedef struct ccsr_pic {
 	char 	res0[106496];	/* 0x26000-0x40000 */
 	char	res1[64];
@@ -1024,17 +1034,18 @@ typedef struct ccsr_pic {
 	char	res150[130892];
 } ccsr_pic_t;
 
-/* CPM Block(0x8_0000-0xc_0000) */
-#if defined(CONFIG_MPC8540) \
-	|| defined(CONFIG_MPC8541) \
-	|| defined(CONFIG_MPC8555)
+/*
+ * CPM Block(0x8_0000-0xc_0000)
+ */
+#ifndef CONFIG_CPM2
 typedef struct ccsr_cpm {
 	char res[262144];
 } ccsr_cpm_t;
 #else
-/* 0x8000-0x8ffff:DPARM */
-
-/* 0x9000-0x90bff: General SIU */
+/*
+ * 0x8000-0x8ffff:DPARM
+ * 0x9000-0x90bff: General SIU
+ */
 typedef struct ccsr_cpm_siu {
 	char 	res1[80];
 	uint	smaer;
@@ -1325,7 +1336,6 @@ typedef struct ccsr_cpm {
 	char            	res1[16*1024];
 	u_char          	im_dpram2[16*1024];
 	char            	res2[16*1024];
-
 	ccsr_cpm_siu_t  	im_cpm_siu;     /* SIU Configuration */
 	ccsr_cpm_intctl_t    	im_cpm_intctl;  /* Interrupt Controller */
 	ccsr_cpm_iop_t       	im_cpm_iop;     /* IO Port control/status */
@@ -1350,8 +1360,10 @@ typedef struct ccsr_cpm {
 	ccsr_cpm_iram_t		im_cpm_iram;
 } ccsr_cpm_t;
 #endif
-/* RapidIO Registers(0xc_0000-0xe_0000) */
 
+/*
+ * RapidIO Registers(0xc_0000-0xe_0000)
+ */
 typedef struct ccsr_rio {
 	uint	didcar;		/* 0xc0000 - Device Identity Capability Register */
 	uint	dicar;		/* 0xc0004 - Device Information Capability Register */
@@ -1517,7 +1529,9 @@ typedef struct ccsr_rio {
 	char	res58[60176];
 } ccsr_rio_t;
 
-/* Global Utilities Register Block(0xe_0000-0xf_ffff) */
+/*
+ * Global Utilities Register Block(0xe_0000-0xf_ffff)
+ */
 typedef struct ccsr_gur {
 	uint	porpllsr;	/* 0xe0000 - POR PLL ratio status register */
 	uint	porbmsr;	/* 0xe0004 - POR boot mode status register */
@@ -1549,7 +1563,13 @@ typedef struct ccsr_gur {
 	uint	ddrdllcr;	/* 0xe0e10 - DDR DLL control register */
 	char	res12[12];
 	uint	lbcdllcr;	/* 0xe0e20 - LBC DLL control register */
-	char	res13[61915];
+	char	res13[248];
+	uint	lbiuiplldcr0;	/* 0xe0f1c -- LBIU PLL Debug Reg 0 */
+	uint	lbiuiplldcr1;	/* 0xe0f20 -- LBIU PLL Debug Reg 1 */
+	uint	ddrioovcr;	/* 0xe0f24 - DDR IO Override Control */
+	uint	res14;		/* 0xe0f28 */
+	uint	tsec34ioovcr;	/* 0xe0f2c - eTSEC 3/4 IO override control */
+	char	res15[61651];
 } ccsr_gur_t;
 
 typedef struct immap {
diff --git a/include/asm-ppc/mpc8349_pci.h b/include/asm-ppc/mpc8349_pci.h
new file mode 100644
index 000000000..48255a34f
--- /dev/null
+++ b/include/asm-ppc/mpc8349_pci.h
@@ -0,0 +1,167 @@
+#ifndef _PPC_KERNEL_MPC8349_PCI_H
+#define _PPC_KERNEL_MPC8349_PCI_H
+
+
+#define M8265_PCIBR0	0x101ac
+#define M8265_PCIBR1	0x101b0
+#define M8265_PCIMSK0	0x101c4
+#define M8265_PCIMSK1	0x101c8
+
+/* Bit definitions for PCIBR registers */
+
+#define PCIBR_ENABLE        0x00000001
+
+/* Bit definitions for PCIMSK registers */
+
+#define PCIMSK_32KB         0xFFFF8000  /* Size of window, smallest */
+#define PCIMSK_64KB         0xFFFF0000
+#define PCIMSK_128KB        0xFFFE0000
+#define PCIMSK_256KB        0xFFFC0000
+#define PCIMSK_512KB        0xFFF80000
+#define PCIMSK_1MB          0xFFF00000
+#define PCIMSK_2MB          0xFFE00000
+#define PCIMSK_4MB          0xFFC00000
+#define PCIMSK_8MB          0xFF800000
+#define PCIMSK_16MB         0xFF000000
+#define PCIMSK_32MB         0xFE000000
+#define PCIMSK_64MB         0xFC000000
+#define PCIMSK_128MB        0xF8000000
+#define PCIMSK_256MB        0xF0000000
+#define PCIMSK_512MB        0xE0000000
+#define PCIMSK_1GB          0xC0000000  /* Size of window, largest */
+
+
+#define M826X_SCCR_PCI_MODE_EN 0x100
+
+
+/*
+ * Outbound ATU registers (3 sets). These registers control how 60x bus
+ * (local) addresses are translated to PCI addresses when the MPC826x is
+ * a PCI bus master (initiator).
+ */
+
+#define POTAR_REG0          0x10800     /* PCI Outbound Translation Addr registers */
+#define POTAR_REG1          0x10818
+#define POTAR_REG2          0x10830
+
+#define POBAR_REG0          0x10808     /* PCI Outbound Base Addr registers */
+#define POBAR_REG1          0x10820
+#define POBAR_REG2          0x10838
+
+#define POCMR_REG0          0x10810     /* PCI Outbound Comparison Mask registers */
+#define POCMR_REG1          0x10828
+#define POCMR_REG2          0x10840
+
+/* Bit definitions for POMCR registers */
+
+#define POCMR_MASK_4KB      0x000FFFFF
+#define POCMR_MASK_8KB      0x000FFFFE
+#define POCMR_MASK_16KB     0x000FFFFC
+#define POCMR_MASK_32KB     0x000FFFF8
+#define POCMR_MASK_64KB     0x000FFFF0
+#define POCMR_MASK_128KB    0x000FFFE0
+#define POCMR_MASK_256KB    0x000FFFC0
+#define POCMR_MASK_512KB    0x000FFF80
+#define POCMR_MASK_1MB      0x000FFF00
+#define POCMR_MASK_2MB      0x000FFE00
+#define POCMR_MASK_4MB      0x000FFC00
+#define POCMR_MASK_8MB      0x000FF800
+#define POCMR_MASK_16MB     0x000FF000
+#define POCMR_MASK_32MB     0x000FE000
+#define POCMR_MASK_64MB     0x000FC000
+#define POCMR_MASK_128MB    0x000F8000
+#define POCMR_MASK_256MB    0x000F0000
+#define POCMR_MASK_512MB    0x000E0000
+#define POCMR_MASK_1GB      0x000C0000
+
+#define POCMR_ENABLE        0x80000000
+#define POCMR_PCI_IO        0x40000000
+#define POCMR_PREFETCH_EN   0x20000000
+
+/* Soft PCI reset */
+
+#define PCI_GCR_REG         0x10880
+
+/* Bit definitions for PCI_GCR registers */
+
+#define PCIGCR_PCI_BUS_EN   0x1
+
+/*
+ * Inbound ATU registers (2 sets). These registers control how PCI
+ * addresses are translated to 60x bus (local) addresses when the
+ * MPC826x is a PCI bus target.
+ */
+
+#define PITAR_REG1          0x108D0
+#define PIBAR_REG1          0x108D8
+#define PICMR_REG1          0x108E0
+#define PITAR_REG0          0x108E8
+#define PIBAR_REG0          0x108F0
+#define PICMR_REG0          0x108F8
+
+/* Bit definitions for PCI Inbound Comparison Mask registers */
+
+#define PICMR_MASK_4KB       0x000FFFFF
+#define PICMR_MASK_8KB       0x000FFFFE
+#define PICMR_MASK_16KB      0x000FFFFC
+#define PICMR_MASK_32KB      0x000FFFF8
+#define PICMR_MASK_64KB      0x000FFFF0
+#define PICMR_MASK_128KB     0x000FFFE0
+#define PICMR_MASK_256KB     0x000FFFC0
+#define PICMR_MASK_512KB     0x000FFF80
+#define PICMR_MASK_1MB       0x000FFF00
+#define PICMR_MASK_2MB       0x000FFE00
+#define PICMR_MASK_4MB       0x000FFC00
+#define PICMR_MASK_8MB       0x000FF800
+#define PICMR_MASK_16MB      0x000FF000
+#define PICMR_MASK_32MB      0x000FE000
+#define PICMR_MASK_64MB      0x000FC000
+#define PICMR_MASK_128MB     0x000F8000
+#define PICMR_MASK_256MB     0x000F0000
+#define PICMR_MASK_512MB     0x000E0000
+#define PICMR_MASK_1GB       0x000C0000
+
+#define PICMR_ENABLE         0x80000000
+#define PICMR_NO_SNOOP_EN    0x40000000
+#define PICMR_PREFETCH_EN    0x20000000
+
+/* PCI error Registers */
+
+#define	PCI_ERROR_STATUS_REG		0x10884
+#define	PCI_ERROR_MASK_REG		0x10888
+#define	PCI_ERROR_CONTROL_REG		0x1088C
+#define PCI_ERROR_ADRS_CAPTURE_REG      0x10890
+#define PCI_ERROR_DATA_CAPTURE_REG      0x10898
+#define PCI_ERROR_CTRL_CAPTURE_REG      0x108A0
+
+/* PCI error Register bit defines */
+
+#define	PCI_ERROR_PCI_ADDR_PAR			0x00000001
+#define	PCI_ERROR_PCI_DATA_PAR_WR		0x00000002
+#define	PCI_ERROR_PCI_DATA_PAR_RD		0x00000004
+#define	PCI_ERROR_PCI_NO_RSP			0x00000008
+#define	PCI_ERROR_PCI_TAR_ABT			0x00000010
+#define	PCI_ERROR_PCI_SERR			0x00000020
+#define	PCI_ERROR_PCI_PERR_RD			0x00000040
+#define	PCI_ERROR_PCI_PERR_WR			0x00000080
+#define	PCI_ERROR_I2O_OFQO			0x00000100
+#define	PCI_ERROR_I2O_IPQO			0x00000200
+#define	PCI_ERROR_IRA				0x00000400
+#define	PCI_ERROR_NMI				0x00000800
+#define	PCI_ERROR_I2O_DBMC			0x00001000
+
+/*
+ * Register pair used to generate configuration cycles on the PCI bus
+ * and access the MPC826x's own PCI configuration registers.
+ */
+
+#define PCI_CFG_ADDR_REG     0x10900
+#define PCI_CFG_DATA_REG     0x10904
+
+/* Bus parking decides where the bus control sits when idle */
+/* If modifying memory controllers for PCI park on the core */
+
+#define PPC_ACR_BUS_PARK_CORE 0x6
+#define PPC_ACR_BUS_PARK_PCI  0x3
+
+#endif /* _PPC_KERNEL_M8260_PCI_H */
diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h
index 806085ed6..6b131b6b0 100644
--- a/include/asm-ppc/processor.h
+++ b/include/asm-ppc/processor.h
@@ -200,6 +200,11 @@
 #define SPRN_HASH1	0x3D2	/* Primary Hash Address Register */
 #define SPRN_HASH2	0x3D3	/* Secondary Hash Address Resgister */
 #define SPRN_HID0	0x3F0	/* Hardware Implementation Register 0 */
+
+#define HID0_ICE_SHIFT		15
+#define HID0_DCE_SHIFT		14
+#define HID0_DLOCK_SHIFT	12
+
 #define   HID0_EMCP	(1<<31)		/* Enable Machine Check pin */
 #define   HID0_EBA	(1<<29)		/* Enable Bus Address Parity */
 #define   HID0_EBD	(1<<28)		/* Enable Bus Data Parity */
@@ -211,10 +216,10 @@
 #define   HID0_NAP	(1<<22)
 #define   HID0_SLEEP	(1<<21)
 #define   HID0_DPM	(1<<20)
-#define   HID0_ICE	(1<<15)		/* Instruction Cache Enable */
-#define   HID0_DCE	(1<<14)		/* Data Cache Enable */
+#define   HID0_ICE	(1<<HID0_ICE_SHIFT)	/* Instruction Cache Enable */
+#define   HID0_DCE	(1<<HID0_DCE_SHIFT)	/* Data Cache Enable */
 #define   HID0_ILOCK	(1<<13)		/* Instruction Cache Lock */
-#define   HID0_DLOCK	(1<<12)		/* Data Cache Lock */
+#define   HID0_DLOCK	(1<<HID0_DLOCK_SHIFT)	/* Data Cache Lock */
 #define   HID0_ICFI	(1<<11)		/* Instr. Cache Flash Invalidate */
 #define   HID0_DCFI	(1<<10)		/* Data Cache Flash Invalidate */
 #define   HID0_DCI	HID0_DCFI
@@ -420,6 +425,7 @@
 #define SPRN_MAS4       0x274   /* MMU Assist Register 4 */
 #define SPRN_MAS5       0x275   /* MMU Assist Register 5 */
 #define SPRN_MAS6       0x276   /* MMU Assist Register 6 */
+#define SPRN_MAS7	0x3B0	/* MMU Assist Register 7 */
 
 #define SPRN_IVOR32     0x210   /* Interrupt Vector Offset Register 32 */
 #define SPRN_IVOR33     0x211   /* Interrupt Vector Offset Register 33 */
@@ -584,6 +590,7 @@
 #define MAS4	SPRN_MAS4
 #define MAS5	SPRN_MAS5
 #define MAS6	SPRN_MAS6
+#define MAS7	SPRN_MAS7
 
 /* Device Control Registers */
 
@@ -794,6 +801,8 @@
 #define SVR_8560	0x8070
 #define SVR_8555	0x8079
 #define SVR_8541	0x807A
+#define SVR_8548	0x8031
+#define SVR_8548_E	0x8039
 
 
 /* I am just adding a single entry for 8260 boards.  I think we may be
diff --git a/include/asm-ppc/u-boot.h b/include/asm-ppc/u-boot.h
index a7593156b..5b6cd6f96 100644
--- a/include/asm-ppc/u-boot.h
+++ b/include/asm-ppc/u-boot.h
@@ -45,6 +45,9 @@ typedef struct bd_info {
 #if defined(CONFIG_MPC5xxx)
 	unsigned long	bi_mbar_base;	/* base of internal registers */
 #endif
+#if defined(CONFIG_MPC83XX)
+	unsigned long	bi_immrbar;
+#endif
 #if defined(CONFIG_MPC8220)
 	unsigned long	bi_mbar_base;	/* base of internal registers */
 	unsigned long   bi_inpfreq;     /* Input Freq, In MHz */
@@ -59,7 +62,7 @@ typedef struct bd_info {
 	unsigned short	bi_ethspeed;	/* Ethernet speed in Mbps */
 	unsigned long	bi_intfreq;	/* Internal Freq, in MHz */
 	unsigned long	bi_busfreq;	/* Bus Freq, in MHz */
-#if defined(CONFIG_8260) || defined(CONFIG_MPC8560)
+#if defined(CONFIG_CPM2)
 	unsigned long	bi_cpmfreq;	/* CPM_CLK Freq, in MHz */
 	unsigned long	bi_brgfreq;	/* BRG_CLK Freq, in MHz */
 	unsigned long	bi_sccfreq;	/* SCC_CLK Freq, in MHz */
diff --git a/include/common.h b/include/common.h
index 625c38989..efc638d88 100644
--- a/include/common.h
+++ b/include/common.h
@@ -83,6 +83,10 @@ typedef volatile unsigned char	vu_char;
 #include <mpc85xx.h>
 #include <asm/immap_85xx.h>
 #endif
+#ifdef CONFIG_MPC83XX
+#include <mpc83xx.h>
+#include <asm/immap_83xx.h>
+#endif
 #ifdef	CONFIG_4xx
 #include <ppc4xx.h>
 #endif
@@ -409,8 +413,9 @@ int	sdram_adjust_866 (void);
 int	adjust_sdram_tbs_8xx (void);
 #if defined(CONFIG_8260)
 int	prt_8260_clks (void);
-#endif
-#if defined(CONFIG_MPC5xxx)
+#elif defined(CONFIG_MPC83XX)
+int print_clock_conf(void);
+#elif defined(CONFIG_MPC5xxx)
 int	prt_mpc5xxx_clks (void);
 #endif
 #if defined(CONFIG_MPC8220)
diff --git a/include/configs/CPU86.h b/include/configs/CPU86.h
index ce7ccc278..09185b1db 100644
--- a/include/configs/CPU86.h
+++ b/include/configs/CPU86.h
@@ -35,6 +35,7 @@
 
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU		*/
 #define CONFIG_CPU86		1	/* ...on a CPU86 board	*/
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 /*
  * select serial console configuration
diff --git a/include/configs/CPU87.h b/include/configs/CPU87.h
index 0e0876f80..c50870fed 100644
--- a/include/configs/CPU87.h
+++ b/include/configs/CPU87.h
@@ -36,6 +36,7 @@
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU		*/
 #define CONFIG_CPU87		1	/* ...on a CPU87 board	*/
 #define CONFIG_PCI
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 /*
  * select serial console configuration
diff --git a/include/configs/IDS8247.h b/include/configs/IDS8247.h
index c4fb01d8a..729b04869 100644
--- a/include/configs/IDS8247.h
+++ b/include/configs/IDS8247.h
@@ -37,6 +37,7 @@
 #define CONFIG_MPC8272_FAMILY	1
 #define CONFIG_IDS8247		1
 #define CPU_ID_STR		"MPC8247"
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 
diff --git a/include/configs/IPHASE4539.h b/include/configs/IPHASE4539.h
index 6b7079edf..c1565fc03 100644
--- a/include/configs/IPHASE4539.h
+++ b/include/configs/IPHASE4539.h
@@ -40,6 +40,8 @@
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU   */
 #define CONFIG_IPHASE4539	1	/* ...on a Interphase 4539 PMC */
 
+#define CONFIG_CPM2		1	/* Has a CPM2 */
+
 /*-----------------------------------------------------------------------
  * select serial console configuration
  *
diff --git a/include/configs/ISPAN.h b/include/configs/ISPAN.h
index 8aa18caa7..65056a21e 100644
--- a/include/configs/ISPAN.h
+++ b/include/configs/ISPAN.h
@@ -31,6 +31,7 @@
 
 #define CONFIG_MPC8260			/* This is an MPC8260 CPU               */
 #define CONFIG_ISPAN			/* ...on one of Interphase iSPAN boards */
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 /*-----------------------------------------------------------------------
  * Select serial console configuration
diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h
index ed8fe6b07..bba476a6a 100644
--- a/include/configs/MPC8260ADS.h
+++ b/include/configs/MPC8260ADS.h
@@ -42,6 +42,8 @@
 
 #define CONFIG_MPC8260ADS	1	/* Motorola PQ2 ADS family board */
 
+#define CONFIG_CPM2		1	/* Has a CPM2 */
+
 /*
  * Figure out if we are booting low via flash HRCW or high via the BCSR.
  */
diff --git a/include/configs/MPC8266ADS.h b/include/configs/MPC8266ADS.h
index 89f2d096f..d8e91a530 100644
--- a/include/configs/MPC8266ADS.h
+++ b/include/configs/MPC8266ADS.h
@@ -51,6 +51,7 @@
 
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU	*/
 #define CONFIG_MPC8266ADS	1	/* ...on motorola ADS board	*/
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
diff --git a/include/configs/MPC8349ADS.h b/include/configs/MPC8349ADS.h
new file mode 100644
index 000000000..d6d2fabee
--- /dev/null
+++ b/include/configs/MPC8349ADS.h
@@ -0,0 +1,584 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc8349ads board configuration file
+ *
+ * Please refer to doc/README.mpc83xxads for more info.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+#define CONFIG_MII
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1	/* E300 Family */
+#define CONFIG_MPC83XX		1	/* MPC83XX family */
+#define CONFIG_MPC8349		1	/* MPC8349 specific */
+#define CONFIG_MPC8349ADS	1	/* MPC8349ADS board specific */
+
+/* FIXME: Real PCI support will come in a follow-up update. */
+#undef CONFIG_PCI
+
+#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+
+#undef CONFIG_DDR_ECC			/* only for ECC DDR module */
+
+#define PCI_66M
+#ifdef PCI_66M
+#define CONFIG_83XX_CLKIN	66000000	/* in Hz */
+#else
+#define CONFIG_83XX_CLKIN	33000000	/* in Hz */
+#endif
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#ifdef PCI_66M
+#define CONFIG_SYS_CLK_FREQ	66000000
+#else
+#define CONFIG_SYS_CLK_FREQ	33000000
+#endif
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F	/* call board_pre_init */
+
+#define CFG_IMMRBAR		0xE0000000
+
+#undef CFG_DRAM_TEST                   /* memory test, takes time */
+#define CFG_MEMTEST_START       0x00000000      /* memtest region */
+#define CFG_MEMTEST_END         0x00100000
+
+/*
+ * DDR Setup
+ */
+
+#define CFG_DDR_BASE	0x00000000	/* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_BASE
+#undef  CONFIG_DDR_2T_TIMING
+#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+
+#if defined(CONFIG_SPD_EEPROM)
+	/*
+	 * Determine DDR configuration from I2C interface.
+	 */
+	#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+#else
+	/*
+	 * Manually set up DDR parameters
+	 */
+	#define CFG_DDR_SIZE	    256		/* Mb */
+	#define CFG_DDR_CONFIG	(CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9)
+	#define CFG_DDR_TIMING_1	0x37344321
+	#define CFG_DDR_TIMING_2	0x00000800  /* P9-45,may need tuning */
+	#define CFG_DDR_CONTROL 	0xc2000000  /* unbuffered,no DYN_PWR */
+	#define CFG_DDR_MODE    	0x00000062  /* DLL,normal,seq,4/2.5 */
+	#define CFG_DDR_INTERVAL	0x05200100  /* autocharge,no open page */
+#endif
+
+/*
+ * SDRAM on the Local Bus
+ */
+#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CFG_FLASH_CFI			/* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER			/* use the CFI driver */
+#define CFG_FLASH_BASE		0xFE000000	/* start of FLASH   */
+#define CFG_FLASH_SIZE		8		/* FLASH size in MB */
+/* #define CFG_FLASH_USE_BUFFER_WRITE */
+
+#define CFG_BR0_PRELIM	(CFG_FLASH_BASE |	/* Flash Base address */ \
+			(2 << BR_PS_SHIFT) |	/* 32 bit port size */	 \
+			BR_V)			/* valid */
+#define CFG_OR0_PRELIM		0xff806ff7	/* 16Mb Flash size*/
+#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE	/* Window base at flash base */
+#define CFG_LBLAWAR0_PRELIM  0x80000016		/* 16Mb window size */
+
+#define CFG_MAX_FLASH_BANKS	1		/* number of banks */
+#define CFG_MAX_FLASH_SECT	64		/* sectors per device */
+
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CFG_MID_FLASH_JUMP      0x7F000000
+#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef  CFG_RAMBOOT
+#endif
+
+/*
+ * BCSR register on local bus 32KB, 8-bit wide for ADS config reg
+ */
+#define CFG_BCSR             0xF8000000
+#define CFG_LBLAWBAR1_PRELIM CFG_BCSR	/* Access window base at BCSR base */
+#define CFG_LBLAWAR1_PRELIM  0x8000000E		/* Access window size 32K */
+#define CFG_BR1_PRELIM	  (CFG_BCSR|0x00000801)	/* Port-size=8bit, MSEL=GPCM */
+#define CFG_OR1_PRELIM		0xFFFFE8f0	/* length 32K */
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 	1
+#define CFG_INIT_RAM_ADDR	0xe4010000   /* Initial RAM address */
+#define CFG_INIT_RAM_END    	0x1000	     /* End of used area in RAM*/
+
+#define CFG_GBL_DATA_SIZE  	0x100     /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN	    	(256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN	    	(128 * 1024) /* Reserved for malloc */
+
+/*
+ * Local Bus LCRR and LBCR regs
+ *    LCRR:  DLL bypass, Clock divider is 4
+ * External Local Bus rate is
+ *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
+ */
+#define CFG_LCRR	(LCRR_DBYP | LCRR_CLKDIV_4)
+#define CFG_LBC_LBCR	0x00000000
+
+#define CFG_LB_SDRAM	/* if board has SRDAM on local bus */
+
+#ifdef CFG_LB_SDRAM
+/*local bus BR2, OR2 definition for SDRAM if soldered on the ADS board*/
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ *    port-size = 32-bits = BR2[19:20] = 11
+ *    no parity checking = BR2[21:22] = 00
+ *    SDRAM for MSEL = BR2[24:26] = 011
+ *    Valid = BR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * FIXME: the top 17 bits of BR2.
+ */
+
+#define CFG_BR2_PRELIM		0xf0001861 /*Port-size=32bit, MSEL=SDRAM*/
+#define CFG_LBLAWBAR2_PRELIM	0xF0000000
+#define CFG_LBLAWAR2_PRELIM	0x80000019 /*64M*/
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ *    64MB mask for AM, OR2[0:7] = 1111 1100
+ *		   XAM, OR2[17:18] = 11
+ *    9 columns OR2[19-21] = 010
+ *    13 rows   OR2[23-25] = 100
+ *    EAD set for extra time OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
+ */
+
+#define CFG_OR2_PRELIM	0xfc006901
+
+#define CFG_LBC_LSRT	0x32000000    /* LB sdram refresh timer, about 6us */
+#define CFG_LBC_MRTPR	0x20000000    /* LB refresh timer prescal, 266MHz/32*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN	(1 << (31 -  1))
+#define CFG_LBC_LSDMR_BSMA1516	(3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617	(4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR5	(3 << (31 - 16))
+#define CFG_LBC_LSDMR_RFCR8	(5 << (31 - 16))
+#define CFG_LBC_LSDMR_RFCR16	(7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT3	(3 << (31 - 19))
+#define CFG_LBC_LSDMR_PRETOACT6	(5 << (31 - 19))
+#define CFG_LBC_LSDMR_PRETOACT7	(7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW3	(3 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW7	(7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6	(6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8	(1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC2	(2 << (31 - 27))
+#define CFG_LBC_LSDMR_WRC3	(3 << (31 - 27))
+#define CFG_LBC_LSDMR_WRC4	(0 << (31 - 27))
+#define CFG_LBC_LSDMR_BUFCMD	(1 << (31 - 29))
+#define CFG_LBC_LSDMR_CL3	(3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
+
+#define CFG_LBC_LSDMR_COMMON    ( CFG_LBC_LSDMR_RFEN            \
+				| CFG_LBC_LSDMR_BSMA1516	\
+				| CFG_LBC_LSDMR_RFCR8		\
+				| CFG_LBC_LSDMR_PRETOACT6	\
+				| CFG_LBC_LSDMR_ACTTORW3	\
+				| CFG_LBC_LSDMR_BL8		\
+				| CFG_LBC_LSDMR_WRC3		\
+				| CFG_LBC_LSDMR_CL3		\
+				)
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CFG_LBC_LSDMR_1		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_PCHALL)
+#define CFG_LBC_LSDMR_2		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_3		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_4		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_MRW)
+#define CFG_LBC_LSDMR_5		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_NORMAL)
+#endif
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX     1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1        (CFG_IMMRBAR+0x4500)
+#define CFG_NS16550_COM2        (CFG_IMMRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* I2C */
+#define  CONFIG_HARD_I2C		/* I2C with hardware support*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
+#define CFG_I2C_OFFSET      0x3000
+#define CFG_I2C2_OFFSET      0x3100
+
+/* TSEC */
+#define CFG_TSEC1_OFFSET 0x24000
+#define CFG_TSEC1 (CFG_IMMRBAR+CFG_TSEC1_OFFSET)
+#define CFG_TSEC2_OFFSET 0x25000
+#define CFG_TSEC2 (CFG_IMMRBAR+CFG_TSEC2_OFFSET)
+
+/* IO Configuration */
+#define CFG_IO_CONF (\
+	IO_CONF_UART |\
+	IO_CONF_TSEC1 |\
+	IO_CONF_IRQ0 |\
+	IO_CONF_IRQ1 |\
+	IO_CONF_IRQ2 |\
+	IO_CONF_IRQ3 |\
+	IO_CONF_IRQ4 |\
+	IO_CONF_IRQ5 |\
+	IO_CONF_IRQ6 |\
+	IO_CONF_IRQ7 )
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI1_IO_BASE	0x00000000
+#define CFG_PCI1_IO_PHYS	0xe2000000
+#define CFG_PCI1_IO_SIZE	0x1000000	/* 16M */
+
+#define CFG_PCI2_MEM_BASE	0xA0000000
+#define CFG_PCI2_MEM_PHYS	CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI2_IO_BASE	0x00000000
+#define CFG_PCI2_IO_PHYS	0xe3000000
+#define CFG_PCI2_IO_SIZE	0x1000000	/* 16M */
+#if defined(CONFIG_PCI)
+
+#define PCI_ALL_PCI1
+#if defined(PCI_64BIT)
+#undef PCI_ALL_PCI1
+#undef PCI_TWO_PCI1
+#undef PCI_ONE_PCI1
+#endif
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+	#define PCI_ENET0_IOADDR	0xFIXME
+	#define PCI_ENET0_MEMADDR	0xFIXME
+	#define PCI_IDSEL_NUMBER	0x0c 	/* slot0->3(IDSEL)=12->15 */
+#endif
+
+#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
+
+#endif	/* CONFIG_PCI */
+
+#if defined(CONFIG_TSEC_ENET)
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 	1
+#endif
+
+#define CONFIG_GMII		1	/* MII PHY management */
+#define CONFIG_MPC83XX_TSEC1	1
+#define CONFIG_MPC83XX_TSEC1_NAME	"TSEC0"
+#define CONFIG_MPC83XX_TSEC2	1
+#define CONFIG_MPC83XX_TSEC2_NAME	"TSEC1"
+#define TSEC1_PHY_ADDR		0
+#define TSEC2_PHY_ADDR		1
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME		"TSEC0"
+
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+	#define CFG_ENV_IS_IN_FLASH	1
+	#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+	#define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+	#define CFG_ENV_SIZE		0x2000
+#else
+	#define CFG_NO_FLASH		1	/* Flash is not usable now */
+	#define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
+	#define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+	#define CFG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_PCI)
+#define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
+				 | CFG_CMD_PING		\
+				 | CFG_CMD_PCI		\
+				 | CFG_CMD_I2C)		\
+				&			\
+				 ~(CFG_CMD_ENV		\
+				  | CFG_CMD_LOADS))
+#else
+#define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
+				 | CFG_CMD_PING		\
+				 | CFG_CMD_I2C)		\
+				&			\
+				 ~(CFG_CMD_ENV		\
+				  | CFG_CMD_LOADS))
+#endif
+#else
+#if defined(CONFIG_PCI)
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
+				| CFG_CMD_PCI		\
+				| CFG_CMD_PING		\
+				| CFG_CMD_I2C)
+#else
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
+				| CFG_CMD_PING		\
+				| CFG_CMD_I2C       \
+				| CFG_CMD_MII       \
+				)
+#endif
+#endif
+
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	*/
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+	#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+	#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE		32768
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
+#endif
+
+#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
+
+#define CFG_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+	HRCWL_DDR_TO_SCB_CLK_1X1 |\
+	HRCWL_CSB_TO_CLKIN_4X1 |\
+	HRCWL_VCO_1X2 |\
+	HRCWL_CORE_TO_CSB_2X1)
+
+#if defined(PCI_64BIT)
+#define CFG_HRCW_HIGH (\
+	HRCWH_PCI_HOST |\
+	HRCWH_64_BIT_PCI |\
+	HRCWH_PCI1_ARBITER_ENABLE |\
+	HRCWH_PCI2_ARBITER_DISABLE |\
+	HRCWH_CORE_ENABLE |\
+	HRCWH_FROM_0X00000100 |\
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT |\
+	HRCWH_TSEC1M_IN_GMII |\
+	HRCWH_TSEC2M_IN_GMII )
+#else
+#define CFG_HRCW_HIGH (\
+	HRCWH_PCI_HOST |\
+	HRCWH_32_BIT_PCI |\
+	HRCWH_PCI1_ARBITER_ENABLE |\
+	HRCWH_PCI2_ARBITER_ENABLE |\
+	HRCWH_CORE_ENABLE |\
+	HRCWH_FROM_0X00000100 |\
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT |\
+	HRCWH_TSEC1M_IN_GMII |\
+	HRCWH_TSEC2M_IN_GMII )
+#endif
+
+#define CFG_HID0_INIT 0x000000000
+
+#define CFG_HID0_FINAL CFG_HID0_INIT
+
+/* #define CFG_HID0_FINAL		(\
+	HID0_ENABLE_INSTRUCTION_CACHE |\
+	HID0_ENABLE_M_BIT |\
+	HID0_ENABLE_ADDRESS_BROADCAST ) */
+
+#define CFG_HID2 0x000000000
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02	/* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR   00:04:9f:11:22:33
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR  00:E0:0C:00:7D:01
+#endif
+
+#define CONFIG_IPADDR    192.168.1.253
+
+#define CONFIG_HOSTNAME	 unknown
+#define CONFIG_ROOTPATH	 /nfsroot
+#define CONFIG_BOOTFILE	 your.uImage
+
+#define CONFIG_SERVERIP  192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK   255.255.255.0
+
+#define CONFIG_LOADADDR  200000	/* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 6	/* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE	 115200
+
+
+#define	CONFIG_EXTRA_ENV_SETTINGS			\
+	"netdev=eth0\0"					\
+	"consoledev=ttyS0\0"				\
+	"ramdiskaddr=400000\0"				\
+	"ramdiskfile=ramfs.83xx\0"
+
+#define CONFIG_NFSBOOTCOMMAND				\
+	"setenv bootargs root=/dev/nfs rw "		\
+	"nfsroot=$serverip:$rootpath "			\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"			\
+	"bootm $loadaddr"
+
+#define CONFIG_RAMBOOTCOMMAND				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $ramdiskaddr $ramdiskfile;"		\
+	"tftp $loadaddr $bootfile;"			\
+	"bootm $loadaddr $ramdiskaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 1c11c6f4b..131c83224 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -41,14 +41,20 @@
 #define CONFIG_MPC8540		1	/* MPC8540 specific */
 #define CONFIG_MPC8540ADS	1	/* MPC8540ADS board specific */
 
+#ifndef CONFIG_HAS_FEC
+#define CONFIG_HAS_FEC		1	/* 8540 has FEC */
+#endif
+
 #define CONFIG_PCI
 #define CONFIG_TSEC_ENET 		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
 #define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
 
 /*
  * sysclk for MPC85xx
@@ -338,17 +344,24 @@
 
 #define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC1_NAME	"TSEC0"
 #define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME	"TSEC1"
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 
+
+#if CONFIG_HAS_FEC
 #define CONFIG_MPC85XX_FEC	1
+#define CONFIG_MPC85XX_FEC_NAME		"FEC"
 #define FEC_PHY_ADDR		3
 #define FEC_PHYIDX		0
+#endif
 
-#define CONFIG_ETHPRIME		"MOTO ENET0"
+/* Options are: TSEC[0-1], FEC */
+#define CONFIG_ETHPRIME		"TSEC0"
 
 #endif	/* CONFIG_TSEC_ENET */
 
diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h
new file mode 100644
index 000000000..1af923103
--- /dev/null
+++ b/include/configs/MPC8540EVAL.h
@@ -0,0 +1,347 @@
+/*
+ * (C) Copyright 2002,2003 Motorola,Inc.
+ * Modified by Lunsheng Wang, lunsheng@sohu.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* mpc8540eval board configuration file */
+/* please refer to doc/README.mpc85xxads for more info */
+/* make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	    /* BOOKE 			*/
+#define CONFIG_E500		1	    /* BOOKE e500 family	*/
+#define CONFIG_MPC85xx		1	    /* MPC8540/MPC8560		*/
+#define CONFIG_MPC8540		1	    /* MPC8540 specific	        */
+#define CONFIG_MPC8540EVAL	1	    /* MPC8540EVAL board specific */
+
+#undef  CONFIG_PCI	         	    /* pci ethernet support	*/
+#define CONFIG_TSEC_ENET 		    /* tsec ethernet support  */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SPD_EEPROM                   /* Use SPD EEPROM for DDR setup */
+#undef  CONFIG_DDR_ECC			    /* only for ECC DDR module */
+#define CONFIG_DDR_DLL                      /* possible DLL fix needed */
+
+/* Using Localbus SDRAM to emulate flash before we can program the flash,
+ * normally you only need a flash-boot image(u-boot.bin),if unsure undef this.
+ * Not availabe for EVAL board
+ */
+#undef CONFIG_RAM_AS_FLASH
+
+/* sysclk for MPC8540EVAL */
+#if defined(CONFIG_SYSCLK_66M)
+	/*
+	 * the oscillator on board is 66Mhz
+	 * can also get 66M clock from external PCI
+	 */
+	#define CONFIG_SYS_CLK_FREQ   66000000
+#else
+	#define CONFIG_SYS_CLK_FREQ   33000000   /* most pci cards are 33Mhz */
+#endif
+
+/* below can be toggled for performance analysis. otherwise use default */
+#define CONFIG_L2_CACHE		    	    /* toggle L2 cache 	*/
+#undef  CONFIG_BTB			    /* toggle branch predition */
+#undef  CONFIG_ADDR_STREAMING		    /* toggle addr streaming   */
+
+#define CONFIG_BOARD_PRE_INIT	1	    /* Call board_pre_init	*/
+
+#undef	CFG_DRAM_TEST			    /* memory test, takes time  */
+#define CFG_MEMTEST_START	0x00200000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x00400000
+
+#if defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET)
+#error "You can only use either PCI Ethernet Card or TSEC Ethernet, not both."
+#endif
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default	*/
+#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR 	*/
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
+
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory  */
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CFG_SDRAM_SIZE		256             /* DDR is now 256MB     */
+
+#if defined(CONFIG_RAM_AS_FLASH)
+#define CFG_LBC_SDRAM_BASE	0xfc000000	/* Localbus SDRAM */
+#else
+#define CFG_LBC_SDRAM_BASE      0xf0000000      /* Localbus SDRAM */
+#endif
+#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 0MB	*/
+
+#if defined(CONFIG_RAM_AS_FLASH)
+#define CFG_FLASH_BASE          0xf8000000      /* start of FLASH  16M  */
+#define CFG_BR0_PRELIM          0xf8001801      /* port size 32bit */
+#else /* Boot from real Flash */
+#define CFG_FLASH_BASE		0xff800000	/* start of FLASH 8M    */
+#define CFG_BR0_PRELIM		0xff801001	/* port size 16bit	*/
+#endif
+
+#define	CFG_OR0_PRELIM		0xff806f67	/* 8MB Flash		*/
+#define CFG_MAX_FLASH_BANKS	1		/* number of banks	*/
+#define CFG_MAX_FLASH_SECT	64		/* sectors per device   */
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000	/* Timeout for Flash Erase (in ms)*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)*/
+#define CFG_FLASH_CFI		1
+
+#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef  CFG_RAMBOOT
+#endif
+
+#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+
+/* Here some DDR setting should be added */
+
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/* local bus definitions */
+#define CFG_BR2_PRELIM		0xf0001861	/* 64MB localbus SDRAM  */
+#define CFG_OR2_PRELIM		0xfc006901
+#define CFG_LBC_LCRR		0x00030004	/* local bus freq divider*/
+#define CFG_LBC_LBCR		0x00000000
+#define CFG_LBC_LSRT		0x20000000
+#define CFG_LBC_MRTPR		0x20000000
+#define CFG_LBC_LSDMR_1		0x2861b723
+#define CFG_LBC_LSDMR_2		0x0861b723
+#define CFG_LBC_LSDMR_3		0x0861b723
+#define CFG_LBC_LSDMR_4		0x1861b723
+#define CFG_LBC_LSDMR_5		0x4061b723
+
+#if defined(CONFIG_RAM_AS_FLASH)
+#define CFG_BR4_PRELIM          0xf8000801      /* 32KB, 8-bit wide for ADS config reg */
+#else
+#define CFG_BR4_PRELIM          0xf8000801      /* 32KB, 8-bit wide for ADS config reg */
+#endif
+#define CFG_OR4_PRELIM          0xffffe1f1
+#define CFG_BCSR                (CFG_BR4_PRELIM & 0xffff8000)
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 	1
+#define CFG_INIT_RAM_ADDR   	0x40000000 	/* Initial RAM address	*/
+#define CFG_INIT_RAM_END    	0x4000	    	/* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE  	128		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN	    	(256 * 1024)    /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN	    	(128 * 1024)    /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX     1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+#define CONFIG_BAUDRATE	 	115200
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* I2C */
+#define  CONFIG_HARD_I2C		/* I2C with hardware support*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
+
+/* General PCI */
+#define CFG_PCI_MEM_BASE	0x80000000
+#define CFG_PCI_MEM_PHYS	0x80000000
+#define CFG_PCI_MEM_SIZE	0x20000000
+#define CFG_PCI_IO_BASE         0xe2000000
+
+#if defined(CONFIG_PCI)
+#define CONFIG_NET_MULTI
+#undef CONFIG_EEPRO100
+#define CONFIG_TULIP
+#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+#if !defined(CONFIG_PCI_PNP)
+#define PCI_ENET0_IOADDR      0xe0000000
+#define PCI_ENET0_MEMADDR     0xe0000000
+#define PCI_IDSEL_NUMBER      0x0c 	/*slot0->3(IDSEL)=12->15*/
+#endif
+#define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup  */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0008
+#elif defined(CONFIG_TSEC_ENET)
+#define CONFIG_NET_MULTI 	1
+#define CONFIG_MII		1	/* MII PHY management	*/
+#define CONFIG_MPC85XX_TSEC1    1
+#define CONFIG_MPC85XX_TSEC1_NAME      "TSEC0"
+#define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME      "TSEC1"
+#define CONFIG_MPC85XX_FEC      1
+#define CONFIG_MPC85XX_FEC_NAME                "FEC"
+#define TSEC1_PHY_ADDR          7
+#define	TSEC2_PHY_ADDR		4
+#define FEC_PHY_ADDR            2
+#define TSEC1_PHYIDX            0
+#define TSEC2_PHYIDX            0
+#define FEC_PHYIDX              0
+/* Options are: TSEC[0-1], FEC */
+#define CONFIG_ETHPRIME                "TSEC0"
+
+#define CONFIG_PHY_M88E1011     1       /* GigaBit Ether PHY    */
+#define INTEL_LXT971_PHY	1
+#endif
+
+#undef DEBUG
+
+/* Environment */
+#ifndef CFG_RAMBOOT
+#if defined(CONFIG_RAM_AS_FLASH)
+#define CFG_ENV_IS_NOWHERE
+#define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0x100000)
+#define CFG_ENV_SIZE		0x2000
+#else
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+#endif
+#define CFG_ENV_SIZE		0x2000
+#else
+/* #define CFG_NO_FLASH		1 */	/* Flash is not usable now	*/
+#define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only	*/
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+#define CFG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_BOOTARGS	"root=/dev/ram rw console=ttyS0,115200"
+#define CONFIG_BOOTCOMMAND	"bootm 0xff800000 0xffa00000"
+#define CONFIG_BOOTDELAY	3 	/* -1 disable autoboot */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
+#if defined(CONFIG_PCI)
+#define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PING \
+				| CFG_CMD_PCI | CFG_CMD_I2C ) & \
+				 ~(CFG_CMD_ENV | CFG_CMD_LOADS ))
+#else
+#define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PING \
+				| CFG_CMD_I2C ) & \
+				 ~(CFG_CMD_ENV | CFG_CMD_LOADS ))
+#endif
+#else
+#if defined(CONFIG_PCI)
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PCI \
+				| CFG_CMD_PING | CFG_CMD_I2C )
+#else
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PING | CFG_CMD_I2C )
+#endif
+#endif
+
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_LOAD_ADDR   0x2000000       /* default load address */
+#define CFG_PROMPT	"MPC8540EVAL=> "/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20) 	/* Initial Memory map for Linux */
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE	32768
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot		*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*****************************/
+/* Environment Configuration */
+/*****************************/
+/* The mac addresses for all ethernet interface */
+/* NOTE: change below for your network setting!!! */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR  00:01:af:07:9b:8a
+#define CONFIG_ETH1ADDR  00:01:af:07:9b:8b
+#define CONFIG_ETH2ADDR  00:01:af:07:9b:8c
+#endif
+
+#define CONFIG_ROOTPATH  /nfsroot
+#define CONFIG_BOOTFILE  your.uImage
+
+#define CONFIG_SERVERIP         192.168.101.1
+#define CONFIG_IPADDR           192.168.101.11
+#define CONFIG_GATEWAYIP        192.168.101.0
+#define CONFIG_NETMASK          255.255.255.0
+
+#define CONFIG_LOADADDR  200000   /* default location for tftp and bootm */
+
+#define CONFIG_HOSTNAME         MPC8540EVAL
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index 3dd4957bc..c96b98b54 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -33,6 +33,7 @@
 #define CONFIG_BOOKE		1	/* BOOKE */
 #define CONFIG_E500		1	/* BOOKE e500 family */
 #define CONFIG_MPC85xx		1	/* MPC8540/60/55/41 */
+#define CONFIG_CPM2		1	/* has CPM2 */
 #define CONFIG_MPC8541		1	/* MPC8541 specific */
 #define CONFIG_MPC8541CDS	1	/* MPC8541CDS board specific */
 
@@ -40,9 +41,12 @@
 #define CONFIG_TSEC_ENET 		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+#undef CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
 
 /*
  * When initializing flash, if we cannot find the manufacturer ID,
@@ -94,18 +98,50 @@ extern unsigned long get_clock_freq(void);
 #error ("CONFIG_SPD_EEPROM is required by MPC85555CDS")
 #endif
 
+#undef CONFIG_CLOCKS_IN_MHZ
+
+
 /*
- * SDRAM on the Local Bus
+ * Local Bus Definitions
  */
-#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
-#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+
+/*
+ * FLASH on the Local Bus
+ * Two banks, 8M each, using the CFI driver.
+ * Boot from BR0/OR0 bank at 0xff00_0000
+ * Alternate BR1/OR1 bank at 0xff80_0000
+ *
+ * BR0, BR1:
+ *    Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
+ *    Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
+ *    Port Size = 16 bits = BRx[19:20] = 10
+ *    Use GPCM = BRx[24:26] = 000
+ *    Valid = BRx[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001    BR0
+ * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001    BR1
+ *
+ * OR0, OR1:
+ *    Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
+ *    Reserved ORx[17:18] = 11, confusion here?
+ *    CSNT = ORx[20] = 1
+ *    ACS = half cycle delay = ORx[21:22] = 11
+ *    SCY = 6 = ORx[24:27] = 0110
+ *    TRLX = use relaxed timing = ORx[29] = 1
+ *    EAD = use external address latch delay = OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65    ORx
+ */
+
 #define CFG_FLASH_BASE		0xff000000	/* start of FLASH 8M */
 
-#define CFG_BR0_PRELIM		0xff801001	/* port size 16bit */
-#define CFG_BR1_PRELIM		0xff001001	/* port size 16bit */
+#define CFG_BR0_PRELIM		0xff801001
+#define CFG_BR1_PRELIM		0xff001001
 
-#define	CFG_OR0_PRELIM		0xff806e61	/* 8MB Flash */
-#define	CFG_OR1_PRELIM		0xff806e61	/* 8MB Flash */
+#define	CFG_OR0_PRELIM		0xff806e65
+#define	CFG_OR1_PRELIM		0xff806e65
 
 #define CFG_FLASH_BANKS_LIST	{0xff800000, CFG_FLASH_BASE}
 #define CFG_MAX_FLASH_BANKS	2		/* number of banks */
@@ -120,11 +156,12 @@ extern unsigned long get_clock_freq(void);
 #define CFG_FLASH_CFI
 #define CFG_FLASH_EMPTY_INFO
 
-#undef CONFIG_CLOCKS_IN_MHZ
 
 /*
- * Local Bus Definitions
+ * SDRAM on the Local Bus
  */
+#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
 
 /*
  * Base Register 2 and Option Register 2 configure SDRAM.
@@ -326,7 +363,9 @@ extern unsigned long get_clock_freq(void);
 
 #define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC1_NAME	"TSEC0"
 #define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME	"TSEC1"
 #undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
@@ -334,7 +373,9 @@ extern unsigned long get_clock_freq(void);
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 #define FEC_PHYIDX		0
-#define CONFIG_ETHPRIME		"MOTO ENET0"
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME		"TSEC0"
 
 #endif	/* CONFIG_TSEC_ENET */
 
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
new file mode 100644
index 000000000..4ca8bc35d
--- /dev/null
+++ b/include/configs/MPC8548CDS.h
@@ -0,0 +1,521 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc8548cds board configuration file
+ *
+ * Please refer to doc/README.mpc85xxcds for more info.
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
+#define CONFIG_MPC8548		1	/* MPC8548 specific */
+#define CONFIG_MPC8548CDS	1	/* MPC8548CDS board specific */
+
+#undef CONFIG_PCI
+#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_DLL			/* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
+
+/*
+ * When initializing flash, if we cannot find the manufacturer ID,
+ * assume this is the AMD flash associated with the CDS board.
+ * This allows booting from a promjet.
+ */
+#define CONFIG_ASSUME_AMD_FLASH
+
+#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_clock_freq(void);
+#endif
+#define CONFIG_SYS_CLK_FREQ	get_clock_freq() /* sysclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE		    	    /* toggle L2 cache 	*/
+#define CONFIG_BTB			    /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING		    /* toggle addr streaming   */
+
+/*
+ * Only possible on E500 Version 2 or newer cores.
+ */
+#define CONFIG_ENABLE_36BIT_PHYS	1
+
+
+#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
+
+#undef	CFG_DRAM_TEST			/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00200000	/* memtest works on */
+#define CFG_MEMTEST_END		0x00400000
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+
+#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+
+/*
+ * Make sure required options are set
+ */
+#ifndef CONFIG_SPD_EEPROM
+#error ("CONFIG_SPD_EEPROM is required")
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+
+/*
+ * Local Bus Definitions
+ */
+
+/*
+ * FLASH on the Local Bus
+ * Two banks, 8M each, using the CFI driver.
+ * Boot from BR0/OR0 bank at 0xff00_0000
+ * Alternate BR1/OR1 bank at 0xff80_0000
+ *
+ * BR0, BR1:
+ *    Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
+ *    Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
+ *    Port Size = 16 bits = BRx[19:20] = 10
+ *    Use GPCM = BRx[24:26] = 000
+ *    Valid = BRx[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001    BR0
+ * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001    BR1
+ *
+ * OR0, OR1:
+ *    Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
+ *    Reserved ORx[17:18] = 11, confusion here?
+ *    CSNT = ORx[20] = 1
+ *    ACS = half cycle delay = ORx[21:22] = 11
+ *    SCY = 6 = ORx[24:27] = 0110
+ *    TRLX = use relaxed timing = ORx[29] = 1
+ *    EAD = use external address latch delay = OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65    ORx
+ */
+
+#define CFG_FLASH_BASE		0xff000000	/* start of FLASH 8M */
+
+#define CFG_BR0_PRELIM		0xff801001
+#define CFG_BR1_PRELIM		0xff001001
+
+#define	CFG_OR0_PRELIM		0xff806e65
+#define	CFG_OR1_PRELIM		0xff806e65
+
+#define CFG_FLASH_BANKS_LIST	{0xff800000, CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS	2		/* number of banks */
+#define CFG_MAX_FLASH_SECT	128		/* sectors per device */
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+
+/*
+ * SDRAM on the Local Bus
+ */
+#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ *    port-size = 32-bits = BR2[19:20] = 11
+ *    no parity checking = BR2[21:22] = 00
+ *    SDRAM for MSEL = BR2[24:26] = 011
+ *    Valid = BR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * FIXME: the top 17 bits of BR2.
+ */
+
+#define CFG_BR2_PRELIM          0xf0001861
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ *    64MB mask for AM, OR2[0:7] = 1111 1100
+ *		   XAM, OR2[17:18] = 11
+ *    9 columns OR2[19-21] = 010
+ *    13 rows   OR2[23-25] = 100
+ *    EAD set for extra time OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
+ */
+
+#define CFG_OR2_PRELIM		0xfc006901
+
+#define CFG_LBC_LCRR		0x00030004    /* LB clock ratio reg */
+#define CFG_LBC_LBCR		0x00000000    /* LB config reg */
+#define CFG_LBC_LSRT		0x20000000  /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR		0x00000000  /* LB refresh timer prescal*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN	(1 << (31 -  1))
+#define CFG_LBC_LSDMR_BSMA1516	(3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617	(4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR16	(7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT7	(7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW7	(7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6	(6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8	(1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC4	(0 << (31 - 27))
+#define CFG_LBC_LSDMR_CL3	(3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
+
+/*
+ * Common settings for all Local Bus SDRAM commands.
+ * At run time, either BSMA1516 (for CPU 1.1)
+ *                  or BSMA1617 (for CPU 1.0) (old)
+ * is OR'ed in too.
+ */
+#define CFG_LBC_LSDMR_COMMON	( CFG_LBC_LSDMR_RFCR16		\
+				| CFG_LBC_LSDMR_PRETOACT7	\
+				| CFG_LBC_LSDMR_ACTTORW7	\
+				| CFG_LBC_LSDMR_BL8		\
+				| CFG_LBC_LSDMR_WRC4		\
+				| CFG_LBC_LSDMR_CL3		\
+				| CFG_LBC_LSDMR_RFEN		\
+				)
+
+/*
+ * The CADMUS registers are connected to CS3 on CDS.
+ * The new memory map places CADMUS at 0xf8000000.
+ *
+ * For BR3, need:
+ *    Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
+ *    port-size = 8-bits  = BR[19:20] = 01
+ *    no parity checking  = BR[21:22] = 00
+ *    GPMC for MSEL       = BR[24:26] = 000
+ *    Valid               = BR[31]    = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
+ *
+ * For OR3, need:
+ *    1 MB mask for AM,   OR[0:16]  = 1111 1111 1111 0000 0
+ *    disable buffer ctrl OR[19]    = 0
+ *    CSNT                OR[20]    = 1
+ *    ACS                 OR[21:22] = 11
+ *    XACS                OR[23]    = 1
+ *    SCY 15 wait states  OR[24:27] = 1111	max is suboptimal but safe
+ *    SETA                OR[28]    = 0
+ *    TRLX                OR[29]    = 1
+ *    EHTR                OR[30]    = 1
+ *    EAD extra time      OR[31]    = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
+ */
+
+#define CADMUS_BASE_ADDR 0xf8000000
+#define CFG_BR3_PRELIM   0xf8000801
+#define CFG_OR3_PRELIM   0xfff00ff7
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 	1
+#define CFG_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
+#define CFG_INIT_RAM_END    	0x4000	    /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE  	128	    /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN	    	(256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN	    	(128 * 1024)	/* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX     2
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* I2C */
+#define CONFIG_HARD_I2C			/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_EEPROM_ADDR	0x57
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI1_IO_BASE	0xe2000000
+#define CFG_PCI1_IO_PHYS	CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE	0x1000000	/* 16M */
+
+#define CFG_PCI2_MEM_BASE	0xa0000000
+#define CFG_PCI2_MEM_PHYS	CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI2_IO_BASE	0xe3000000
+#define CFG_PCI2_IO_PHYS	CFG_PCI2_IO_BASE
+#define CFG_PCI2_IO_SIZE	0x1000000	/* 16M */
+
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+    #define PCI_ENET0_IOADDR      0xe0000000
+    #define PCI_ENET0_MEMADDR     0xe0000000
+    #define PCI_IDSEL_NUMBER      0x0c 	/*slot0->3(IDSEL)=12->15*/
+#endif
+
+#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
+
+#endif	/* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 	1
+#endif
+
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC1_NAME	"eTSEC0"
+#define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME	"eTSEC1"
+#define CONFIG_MPC85XX_TSEC3	1
+#define CONFIG_MPC85XX_TSEC3_NAME	"eTSEC2"
+#define CONFIG_MPC85XX_TSEC4	1
+#define CONFIG_MPC85XX_TSEC4_NAME	"eTSEC3"
+#undef CONFIG_MPC85XX_FEC
+
+#define TSEC1_PHY_ADDR		0
+#define TSEC2_PHY_ADDR		1
+#define TSEC3_PHY_ADDR		2
+#define TSEC4_PHY_ADDR		3
+#define FEC_PHY_ADDR		3
+
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define TSEC3_PHYIDX		0
+#define TSEC4_PHYIDX		0
+#define FEC_PHYIDX		0
+
+/* Options are: eTSEC[0-3] */
+#define CONFIG_ETHPRIME		"eTSEC0"
+
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+#define CFG_ENV_SIZE		0x2000
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+#if defined(CONFIG_PCI)
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
+				| CFG_CMD_PCI \
+				| CFG_CMD_PING \
+				| CFG_CMD_I2C \
+				| CFG_CMD_MII)
+#else
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
+				| CFG_CMD_PING \
+				| CFG_CMD_I2C \
+				| CFG_CMD_MII)
+#endif
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	*/
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20) 	/* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE	32768
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR   00:E0:0C:00:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
+#endif
+
+#define CONFIG_IPADDR    192.168.1.253
+
+#define CONFIG_HOSTNAME  unknown
+#define CONFIG_ROOTPATH  /nfsroot
+#define CONFIG_BOOTFILE  your.uImage
+
+#define CONFIG_SERVERIP  192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK   255.255.255.0
+
+#define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/
+
+#define CONFIG_BOOTDELAY 10       /* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS           /* the boot command will set bootargs*/
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				        \
+   "netdev=eth0\0"                                                      \
+   "consoledev=ttyS1\0"                                                 \
+   "ramdiskaddr=400000\0"                                               \
+   "ramdiskfile=your.ramdisk.u-boot\0"
+
+#define CONFIG_NFSBOOTCOMMAND	                                        \
+   "setenv bootargs root=/dev/nfs rw "                                  \
+      "nfsroot=$serverip:$rootpath "                                    \
+      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+      "console=$consoledev,$baudrate $othbootargs;"                     \
+   "tftp $loadaddr $bootfile;"                                          \
+   "bootm $loadaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+   "setenv bootargs root=/dev/ram rw "                                  \
+      "console=$consoledev,$baudrate $othbootargs;"                     \
+   "tftp $ramdiskaddr $ramdiskfile;"                                    \
+   "tftp $loadaddr $bootfile;"                                          \
+   "bootm $loadaddr $ramdiskaddr"
+
+#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index 379a12cc6..a44e3ec84 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -33,6 +33,7 @@
 #define CONFIG_BOOKE		1	/* BOOKE */
 #define CONFIG_E500		1	/* BOOKE e500 family */
 #define CONFIG_MPC85xx		1	/* MPC8540/60/55/41 */
+#define CONFIG_CPM2		1	/* has CPM2 */
 #define CONFIG_MPC8555		1	/* MPC8555 specific */
 #define CONFIG_MPC8555CDS	1	/* MPC8555CDS board specific */
 
@@ -40,9 +41,12 @@
 #define CONFIG_TSEC_ENET 		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+#undef CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
 
 /*
  * When initializing flash, if we cannot find the manufacturer ID,
@@ -94,18 +98,50 @@ extern unsigned long get_clock_freq(void);
 #error ("CONFIG_SPD_EEPROM is required by MPC85555CDS")
 #endif
 
+#undef CONFIG_CLOCKS_IN_MHZ
+
+
 /*
- * SDRAM on the Local Bus
+ * Local Bus Definitions
  */
-#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
-#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+
+/*
+ * FLASH on the Local Bus
+ * Two banks, 8M each, using the CFI driver.
+ * Boot from BR0/OR0 bank at 0xff00_0000
+ * Alternate BR1/OR1 bank at 0xff80_0000
+ *
+ * BR0, BR1:
+ *    Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
+ *    Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
+ *    Port Size = 16 bits = BRx[19:20] = 10
+ *    Use GPCM = BRx[24:26] = 000
+ *    Valid = BRx[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001    BR0
+ * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001    BR1
+ *
+ * OR0, OR1:
+ *    Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
+ *    Reserved ORx[17:18] = 11, confusion here?
+ *    CSNT = ORx[20] = 1
+ *    ACS = half cycle delay = ORx[21:22] = 11
+ *    SCY = 6 = ORx[24:27] = 0110
+ *    TRLX = use relaxed timing = ORx[29] = 1
+ *    EAD = use external address latch delay = OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65    ORx
+ */
+
 #define CFG_FLASH_BASE		0xff000000	/* start of FLASH 8M */
 
-#define CFG_BR0_PRELIM		0xff801001	/* port size 16bit */
-#define CFG_BR1_PRELIM		0xff001001	/* port size 16bit */
+#define CFG_BR0_PRELIM		0xff801001
+#define CFG_BR1_PRELIM		0xff001001
 
-#define	CFG_OR0_PRELIM		0xff806e61	/* 8MB Flash */
-#define	CFG_OR1_PRELIM		0xff806e61	/* 8MB Flash */
+#define	CFG_OR0_PRELIM		0xff806e65
+#define	CFG_OR1_PRELIM		0xff806e65
 
 #define CFG_FLASH_BANKS_LIST	{0xff800000, CFG_FLASH_BASE}
 #define CFG_MAX_FLASH_BANKS	2		/* number of banks */
@@ -120,11 +156,12 @@ extern unsigned long get_clock_freq(void);
 #define CFG_FLASH_CFI
 #define CFG_FLASH_EMPTY_INFO
 
-#undef CONFIG_CLOCKS_IN_MHZ
 
 /*
- * Local Bus Definitions
+ * SDRAM on the Local Bus
  */
+#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
 
 /*
  * Base Register 2 and Option Register 2 configure SDRAM.
@@ -326,7 +363,9 @@ extern unsigned long get_clock_freq(void);
 
 #define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC1_NAME	"TSEC0"
 #define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME	"TSEC1"
 #undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
@@ -334,7 +373,9 @@ extern unsigned long get_clock_freq(void);
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 #define FEC_PHYIDX		0
-#define CONFIG_ETHPRIME		"MOTO ENET0"
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME		"TSEC0"
 
 #endif	/* CONFIG_TSEC_ENET */
 
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 727173738..db878cb19 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -38,7 +38,7 @@
 #define CONFIG_BOOKE		1	/* BOOKE */
 #define CONFIG_E500		1	/* BOOKE e500 family */
 #define CONFIG_MPC85xx		1	/* MPC8540/MPC8560 */
-#define CONFIG_MPC8560		1	/* MPC8560 specific */
+#define CONFIG_CPM2		1	/* has CPM2 */
 #define CONFIG_MPC8560ADS	1	/* MPC8560ADS board specific */
 
 #define CONFIG_PCI
@@ -46,10 +46,12 @@
 #undef  CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
 #define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
 
 /*
  * sysclk for MPC85xx
@@ -337,13 +339,17 @@
 
 #define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC1_NAME	"TSEC0"
 #define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME	"TSEC1"
 #undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
-#define CONFIG_ETHPRIME		"MOTO ENET0"
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME		"TSEC0"
 
 #elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
 
diff --git a/include/configs/PM826.h b/include/configs/PM826.h
index a4c4fc973..9ca1e5229 100644
--- a/include/configs/PM826.h
+++ b/include/configs/PM826.h
@@ -37,6 +37,7 @@
 
 #define CONFIG_MPC8260		1	/* This is a MPC8260 CPU	*/
 #define CONFIG_PM826		1	/* ...on a PM8260 module	*/
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 #undef CONFIG_DB_CR826_J30x_ON		/* J30x jumpers on D.B. carrier	*/
 
diff --git a/include/configs/PM828.h b/include/configs/PM828.h
index 5b71c960f..7d98df5ca 100644
--- a/include/configs/PM828.h
+++ b/include/configs/PM828.h
@@ -37,6 +37,7 @@
 
 #define CONFIG_MPC8260		1	/* This is a MPC8260 CPU	*/
 #define CONFIG_PM828		1	/* ...on a PM828 module */
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 #undef CONFIG_DB_CR826_J30x_ON		/* J30x jumpers on D.B. carrier */
 
diff --git a/include/configs/PM854.h b/include/configs/PM854.h
index b3e1f5e98..07e3f06ac 100644
--- a/include/configs/PM854.h
+++ b/include/configs/PM854.h
@@ -45,10 +45,12 @@
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #undef	CONFIG_SPD_EEPROM		/* do not use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
 #define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
 
 /*
  * sysclk for MPC85xx
@@ -256,17 +258,21 @@
 
 #define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC1_NAME	"TSEC0"
 #define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME	"TSEC1"
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 
 #define CONFIG_MPC85XX_FEC	1
+#define CONFIG_MPC85XX_FEC_NAME		"FEC"
 #define FEC_PHY_ADDR		3
 #define FEC_PHYIDX		0
 
-#define CONFIG_ETHPRIME		"ENET0"
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME		"TSEC0"
 
 #define	CONFIG_HAS_ETH1		1
 #define	CONFIG_HAS_ETH2		1
diff --git a/include/configs/RPXsuper.h b/include/configs/RPXsuper.h
index cdf716cb2..6ae9403c4 100644
--- a/include/configs/RPXsuper.h
+++ b/include/configs/RPXsuper.h
@@ -173,6 +173,7 @@
 
 #define CONFIG_MPC8260          1       /* This is an MPC8260 CPU   */
 #define CONFIG_RPXSUPER         1       /* on an Embedded Planet RPX Super Board  */
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
diff --git a/include/configs/Rattler.h b/include/configs/Rattler.h
index f98a6c60b..a55297096 100644
--- a/include/configs/Rattler.h
+++ b/include/configs/Rattler.h
@@ -33,6 +33,8 @@
 #define CPU_ID_STR		"MPC8250"
 #endif /* CONFIG_MPC8248 */
 
+#define CONFIG_CPM2		1	/* Has a CPM2 */
+
 #define CONFIG_RATTLER			/* Analogue&Micro Rattler board */
 
 #undef DEBUG
diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h
index 60561eb22..0451b2081 100644
--- a/include/configs/SBC8540.h
+++ b/include/configs/SBC8540.h
@@ -46,7 +46,7 @@
 #define CONFIG_MPC85xx_REV1	1	/* MPC85xx Rev 1.0 chip		*/
 
 
-#define CONFIG_MPC8560		1	/* MPC8560 (CPU) specific		*/
+#define CONFIG_CPM2		1	/* has CPM2 */
 
 #define CONFIG_SBC8540      	1   	/* configuration for SBC8560 board */
 
@@ -227,10 +227,14 @@
 
 #if defined(CONFIG_TSEC_ENET)		/* TSEC Ethernet port */
 
-  #define CONFIG_NET_MULTI	1
-  #define CONFIG_PHY_BCM5421S		/* GigaBit Ether PHY	     */
-  #define CONFIG_MII		1	/* MII PHY management		*/
-  #define CONFIG_PHY_ADDR	25	/* PHY address			*/
+#  define CONFIG_NET_MULTI	1
+#  define CONFIG_MPC85xx_TSEC1
+#  define CONFIG_MPC85xx_TSEC1_NAME	"TSEC0"
+#  define CONFIG_MII		1	/* MII PHY management		*/
+#  define TSEC1_PHY_ADDR	25
+#  define TSEC1_PHYIDX		0
+/* Options are: TSEC0 */
+#  define CONFIG_ETHPRIME		"TSEC0"
 
 
 #elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
diff --git a/include/configs/SBC8560.h b/include/configs/SBC8560.h
index 6bd0abe76..8b46a17ed 100644
--- a/include/configs/SBC8560.h
+++ b/include/configs/SBC8560.h
@@ -46,7 +46,7 @@
 #define CONFIG_MPC85xx_REV1	1	/* MPC85xx Rev 1.0 chip		*/
 
 
-#define CONFIG_MPC8560		1	/* MPC8560 (CPU) specific		*/
+#define CONFIG_CPM2		1	/* has CPM2 */
 #define CONFIG_SBC8560      	1   	/* configuration for SBC8560 board */
 
 #define CONFIG_MPC8560ADS	1	/* MPC8560ADS board specific (supplement)	*/
@@ -215,10 +215,14 @@
 
 #if defined(CONFIG_TSEC_ENET)		/* TSEC Ethernet port */
 
-  #define CONFIG_NET_MULTI	1
-  #define CONFIG_PHY_BCM5421S		/* GigaBit Ether PHY	     */
-  #define CONFIG_MII		1	/* MII PHY management		*/
-  #define CONFIG_PHY_ADDR	25	/* PHY address			*/
+#  define CONFIG_NET_MULTI	1
+#  define CONFIG_MII		1	/* MII PHY management		*/
+#  define CONFIG_MPC85xx_TSEC1
+#  define CONFIG_MPC85xx_TSEC1_NAME	"TSEC0"
+#  define TSEC1_PHY_ADDR	25
+#  define TSEC1_PHYIDX		0
+/* Options are: TSEC0 */
+#  define CONFIG_ETHPRIME		"TSEC0"
 
 
 #elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
diff --git a/include/configs/SCM.h b/include/configs/SCM.h
index e4533b465..91914e80d 100644
--- a/include/configs/SCM.h
+++ b/include/configs/SCM.h
@@ -36,6 +36,7 @@
 #define CONFIG_MPC8260		1	/* This is a MPC8260 CPU		*/
 #define CONFIG_TQM8260		200	/* ...on a TQM8260 module Rev.200	*/
 #define CONFIG_SCM              1	/* ...on a System Controller Module	*/
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 #if (CONFIG_TQM8260 <= 100)
 #  error "TQM8260 module revison not supported"
diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h
index eaf138acb..e6266b58d 100644
--- a/include/configs/TQM8260.h
+++ b/include/configs/TQM8260.h
@@ -52,6 +52,8 @@
 #define CONFIG_TQM8260		200	/* ...on a TQM8260 module Rev.200	*/
 #endif
 
+#define CONFIG_CPM2		1	/* Has a CPM2 */
+
 #define CONFIG_82xx_CONS_SMC1	1	/* console on SMC1			*/
 
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
diff --git a/include/configs/TQM8540.h b/include/configs/TQM8540.h
index 9dc77c4bd..8438b9325 100644
--- a/include/configs/TQM8540.h
+++ b/include/configs/TQM8540.h
@@ -280,20 +280,24 @@
 
 #define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC1_NAME	"TSEC0"
 #define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME	"TSEC1"
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 
 #define CONFIG_MPC85XX_FEC	1
+#define CONFIG_MPC85XX_FEC_NAME	"FEC"
 #define FEC_PHY_ADDR		2
 #define FEC_PHYIDX		0
 
 #define CONFIG_HAS_ETH1
 #define CONFIG_HAS_ETH2
 
-#define CONFIG_ETHPRIME		"ENET1"
+/* Options are TSEC[0-1], FEC */
+#define CONFIG_ETHPRIME		"TSEC1"
 
 #endif	/* CONFIG_TSEC_ENET */
 
diff --git a/include/configs/TQM8560.h b/include/configs/TQM8560.h
index f418e2634..1466f3178 100644
--- a/include/configs/TQM8560.h
+++ b/include/configs/TQM8560.h
@@ -276,6 +276,7 @@
 
 #define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME	"TSEC1"
 #define TSEC2_PHY_ADDR		1
 #define TSEC2_PHYIDX		0
 
@@ -288,7 +289,7 @@
 #define CFG_CPMFCR_RAMTYPE    0
 #define CFG_FCC_PSMR          (FCC_PSMR_FDE | FCC_PSMR_LPB)
 
-#define CONFIG_ETHPRIME		"ENET1"
+#define CONFIG_ETHPRIME		"TSEC1"
 
 /*
  * Environment
diff --git a/include/configs/ZPC1900.h b/include/configs/ZPC1900.h
index 685797327..f71e691b2 100644
--- a/include/configs/ZPC1900.h
+++ b/include/configs/ZPC1900.h
@@ -30,6 +30,7 @@
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU      */
 #define CONFIG_ZPC1900		1	/* ...on Zephyr ZPC.1900 board */
 #define CPU_ID_STR		"MPC8265"
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 #undef DEBUG
 
diff --git a/include/configs/atc.h b/include/configs/atc.h
index 275124830..881a4caee 100644
--- a/include/configs/atc.h
+++ b/include/configs/atc.h
@@ -35,6 +35,7 @@
 
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU		*/
 #define CONFIG_ATC		1	/* ...on a ATC board	*/
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 /*
  * select serial console configuration
diff --git a/include/configs/cogent_mpc8260.h b/include/configs/cogent_mpc8260.h
index b3ec89b05..aea2e6436 100644
--- a/include/configs/cogent_mpc8260.h
+++ b/include/configs/cogent_mpc8260.h
@@ -35,6 +35,7 @@
 
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU	*/
 #define CONFIG_COGENT		1	/* using Cogent Modular Architecture */
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
 
diff --git a/include/configs/ep8260.h b/include/configs/ep8260.h
index fb335db80..98e1716bf 100644
--- a/include/configs/ep8260.h
+++ b/include/configs/ep8260.h
@@ -48,6 +48,8 @@
 #define CFG_EP8260_H2	1
 /* #undef CFG_EP8260_H2  */
 
+#define CONFIG_CPM2		1	/* Has a CPM2 */
+
 /* What is the oscillator's (UX2) frequency in Hz? */
 #define CONFIG_8260_CLKIN  (66 * 1000 * 1000)
 
diff --git a/include/configs/gw8260.h b/include/configs/gw8260.h
index 3666bdbb7..6c080437f 100644
--- a/include/configs/gw8260.h
+++ b/include/configs/gw8260.h
@@ -330,6 +330,7 @@
 
 #define CONFIG_MPC8260      1   /* This is an MPC8260 CPU   */
 #define CONFIG_GW8260       1   /* on an GW8260 Board  */
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
diff --git a/include/configs/hymod.h b/include/configs/hymod.h
index 90d6b25bd..0d62b9efd 100644
--- a/include/configs/hymod.h
+++ b/include/configs/hymod.h
@@ -35,6 +35,7 @@
 
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU	*/
 #define CONFIG_HYMOD		1	/* ...on a Hymod board		*/
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
 
diff --git a/include/configs/ppmc8260.h b/include/configs/ppmc8260.h
index 2ad286735..60b0b3713 100644
--- a/include/configs/ppmc8260.h
+++ b/include/configs/ppmc8260.h
@@ -297,6 +297,7 @@
 
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU   */
 #define CONFIG_PPMC8260		1	/* on an Wind River PPMC8260 Board  */
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
diff --git a/include/configs/rsdproto.h b/include/configs/rsdproto.h
index b1f6cb20e..6c9e392c3 100644
--- a/include/configs/rsdproto.h
+++ b/include/configs/rsdproto.h
@@ -37,6 +37,7 @@
 
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU	*/
 #define CONFIG_RSD_PROTO	1	/* on a R&S Protocol Board      */
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
 
diff --git a/include/configs/sacsng.h b/include/configs/sacsng.h
index cc9774c6a..031eba597 100644
--- a/include/configs/sacsng.h
+++ b/include/configs/sacsng.h
@@ -544,6 +544,7 @@
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU   */
 #define CONFIG_SBC8260		1	/* on an EST SBC8260 Board  */
 #define CONFIG_SACSng		1	/* munged for the SACSng */
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
diff --git a/include/configs/sbc8260.h b/include/configs/sbc8260.h
index dc9cec360..45e4494ec 100644
--- a/include/configs/sbc8260.h
+++ b/include/configs/sbc8260.h
@@ -481,6 +481,7 @@
 
 #define CONFIG_MPC8260		1	/* This is an MPC8260 CPU   */
 #define CONFIG_SBC8260		1	/* on an EST SBC8260 Board  */
+#define CONFIG_CPM2		1	/* Has a CPM2 */
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index 8cf9eeb3d..5a434dc76 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -40,7 +40,7 @@
 #define CONFIG_MPC85xx_REV1	1	/* MPC85xx Rev 1.0 chip		*/
 
 
-#define CONFIG_MPC8560		1	/* MPC8560 specific		*/
+#define CONFIG_CPM2		1	/* has CPM2 */
 #define CONFIG_SBC8560		1	/* configuration for SBC8560 board */
 
 /* XXX flagging this as something I might want to delete */
@@ -210,10 +210,14 @@
 
 #if defined(CONFIG_TSEC_ENET)		/* TSEC Ethernet port */
 
-  #define CONFIG_NET_MULTI	1
-  #define CONFIG_PHY_BCM5421S	1	/* GigaBit Ether PHY	     */
-  #define CONFIG_MII		1	/* MII PHY management		*/
-  #define CONFIG_PHY_ADDR	25	/* PHY address			*/
+#  define CONFIG_NET_MULTI	1
+#  define CONFIG_MII		1	/* MII PHY management		*/
+#  define CONFIG_MPC85xx_TSEC1
+#  define CONFIG_MPC85xx_TSEC1_NAME	"TSEC0"
+#  define TSEC1_PHY_ADDR	25
+#  define TSEC1_PHYIDX		0
+/* Options are: TSEC0 */
+#  define CONFIG_ETHPRIME		"TSEC0"
 
 #elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
 
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index e9261db30..e218597db 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -39,7 +39,7 @@
 #define CONFIG_BOOKE		1	/* BOOKE		*/
 #define CONFIG_E500		1	/* BOOKE e500 family	*/
 #define CONFIG_MPC85xx		1	/* MPC8540/MPC8560	*/
-#define CONFIG_MPC8560		1	/* MPC8560 specific	*/
+#define CONFIG_CPM2		1	/* has CPM2 */
 #define CONFIG_STXGP3		1	/* Silicon Tx GPPP board specific*/
 
 #undef  CONFIG_PCI	         	/* pci ethernet support	*/
@@ -227,14 +227,16 @@
 #define CONFIG_MII		1	/* MII PHY management		*/
 
 #define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC1_NAME	"TSEC0"
 #define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME	"TSEC1"
 #undef CONFIG_MPS85XX_FEC
 
 #define TSEC1_PHY_ADDR		2
 #define TSEC2_PHY_ADDR		4
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
-#define CONFIG_ETHPRIME		"MOTO ENET0"
+#define CONFIG_ETHPRIME		"TSEC0"
 
 #elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
 
diff --git a/include/ioports.h b/include/ioports.h
index eba9aee0d..d7e19e195 100644
--- a/include/ioports.h
+++ b/include/ioports.h
@@ -25,7 +25,7 @@ typedef struct {
  * the internal memory map aligns the above structure on
  * a 0x20 byte boundary
  */
-#ifdef CONFIG_MPC8560
+#ifdef CONFIG_MPC85xx
 #define ioport_addr(im, idx) (ioport_t *)((uint)&((im)->im_cpm.im_cpm_iop) + ((idx)*0x20))
 #else
 #define ioport_addr(im, idx) (ioport_t *)((uint)&(im)->im_ioport + ((idx)*0x20))
diff --git a/include/mpc83xx.h b/include/mpc83xx.h
new file mode 100644
index 000000000..38f7115b1
--- /dev/null
+++ b/include/mpc83xx.h
@@ -0,0 +1,288 @@
+/*
+ * Copyright 2004 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc83xx.h
+ *
+ * MPC83xx specific definitions
+ */
+
+#ifndef __MPC83XX_H__
+#define __MPC83XX_H__
+
+#if defined(CONFIG_E300)
+#include <asm/e300.h>
+#endif
+
+/*
+ * MPC83xx cpu provide RCR register to do reset thing specially. easier
+ * to implement
+ */
+
+#define MPC83xx_RESET
+
+/*
+ * System reset offset (PowerPC standard)
+ */
+#define EXC_OFF_SYS_RESET	0x0100
+
+/*
+ * Default Internal Memory Register Space (Freescale recomandation)
+ */
+#define CONFIG_DEFAULT_IMMR 0xFF400000
+
+/*
+ * Watchdog
+ */
+#define SWCRR      0x0204
+#define SWCRR_SWTC 0xFFFF0000 /* Software Watchdog Time Count. */
+#define SWCRR_SWEN 0x00000004 /* Watchdog Enable bit. */
+#define SWCRR_SWRI 0x00000002 /* Software Watchdog Reset/Interrupt Select bit. */
+#define SWCRR_SWPR 0x00000001 /* Software Watchdog Counter Prescale bit. */
+#define SWCRR_RES  ~(SWCRR_SWTC | SWCRR_SWEN | SWCRR_SWRI | SWCRR_SWPR)
+
+#define SWCNR      0x0208
+#define SWCNR_SWCN 0x0000FFFF Software Watchdog Count Field.
+#define SWCNR_RES  ~(SWCNR_SWCN)
+
+#define SWSRR      0x020E
+
+/*
+ * Default Internal Memory Register Space (Freescale recomandation)
+ */
+#define IMMRBAR 0x0000
+#define IMMRBAR_BASE_ADDR     0xFFF00000 /* Identifies the 12 most-significant address bits of the base of the 1 MByte internal memory window. */
+#define IMMRBAR_RES           ~(IMMRBAR_BASE_ADDR)
+
+/*
+ * Default Internal Memory Register Space (Freescale recomandation)
+ */
+#define LBLAWBAR0 0x0020
+#define LBLAWAR0  0x0024
+#define LBLAWBAR1 0x0028
+#define LBLAWAR1  0x002C
+#define LBLAWBAR2 0x0030
+#define LBLAWAR2  0x0034
+#define LBLAWBAR3 0x0038
+#define LBLAWAR3  0x003C
+
+
+/*
+ * Base Registers & Option Registers
+ */
+#define BR0 0x5000
+#define BR1 0x5008
+#define BR2 0x5010
+#define BR3 0x5018
+#define BR4 0x5020
+#define BR5 0x5028
+#define BR6 0x5030
+#define BR7 0x5038
+
+#define BR_BA   0xFFFF8000
+#define BR_BA_SHIFT     15
+#define BR_PS   0x00001800
+#define BR_PS_SHIFT     11
+#define BR_DECC 0x00000600
+#define BR_DECC_SHIFT    9
+#define BR_WP   0x00000100
+#define BR_WP_SHIFT      8
+#define BR_MSEL 0x000000E0
+#define BR_MSEL_SHIFT    5
+#define BR_V    0x00000001
+#define BR_V_SHIFT       0
+#define BR_RES  ~(BR_BA|BR_PS|BR_DECC|BR_WP|BR_MSEL|BR_V)
+
+#define OR0 0x5004
+#define OR1 0x500C
+#define OR2 0x5014
+#define OR3 0x501C
+#define OR4 0x5024
+#define OR5 0x502C
+#define OR6 0x5034
+#define OR7 0x503C
+
+#define OR_GPCM_AM    0xFFFF8000
+#define OR_GPCM_AM_SHIFT      15
+#define OR_GPCM_BCTLD 0x00001000
+#define OR_GPCM_BCTLD_SHIFT   12
+#define OR_GPCM_CSNT  0x00000800
+#define OR_GPCM_CSNT_SHIFT    11
+#define OR_GPCM_ACS   0x00000600
+#define OR_GPCM_ACS_SHIFT      9
+#define OR_GPCM_XACS  0x00000100
+#define OR_GPCM_XACS_SHIFT     8
+#define OR_GPCM_SCY   0x000000F0
+#define OR_GPCM_SCY_SHIFT      4
+#define OR_GPCM_SETA  0x00000008
+#define OR_GPCM_SETA_SHIFT     3
+#define OR_GPCM_TRLX  0x00000004
+#define OR_GPCM_TRLX_SHIFT     2
+#define OR_GPCM_EHTR  0x00000002
+#define OR_GPCM_EHTR_SHIFT     1
+#define OR_GPCM_EAD   0x00000001
+#define OR_GPCM_EAD_SHIFT      0
+
+#define OR_UPM_AM    0xFFFF8000
+#define OR_UPM_AM_SHIFT      15
+#define OR_UPM_XAM   0x00006000
+#define OR_UPM_XAM_SHIFT     13
+#define OR_UPM_BCTLD 0x00001000
+#define OR_UPM_BCTLD_SHIFT   12
+#define OR_UPM_BI    0x00000100
+#define OR_UPM_BI_SHIFT       8
+#define OR_UPM_TRLX  0x00000004
+#define OR_UPM_TRLX_SHIFT     2
+#define OR_UPM_EHTR  0x00000002
+#define OR_UPM_EHTR_SHIFT     1
+#define OR_UPM_EAD   0x00000001
+#define OR_UPM_EAD_SHIFT      0
+
+#define OR_SDRAM_AM    0xFFFF8000
+#define OR_SDRAM_AM_SHIFT      15
+#define OR_SDRAM_XAM   0x00006000
+#define OR_SDRAM_XAM_SHIFT     13
+#define OR_SDRAM_COLS  0x00001C00
+#define OR_SDRAM_COLS_SHIFT    10
+#define OR_SDRAM_ROWS  0x000001C0
+#define OR_SDRAM_ROWS_SHIFT     6
+#define OR_SDRAM_PMSEL 0x00000020
+#define OR_SDRAM_PMSEL_SHIFT    5
+#define OR_SDRAM_EAD   0x00000001
+#define OR_SDRAM_EAD_SHIFT      0
+
+/*
+ * Hard Reset Configration Word - High
+ */
+#define HRCWH_PCI_AGENT              0x00000000
+#define HRCWH_PCI_HOST               0x80000000
+
+#define HRCWH_32_BIT_PCI             0x00000000
+#define HRCWH_64_BIT_PCI             0x40000000
+
+#define HRCWH_PCI1_ARBITER_DISABLE   0x00000000
+#define HRCWH_PCI1_ARBITER_ENABLE    0x20000000
+
+#define HRCWH_PCI2_ARBITER_DISABLE   0x00000000
+#define HRCWH_PCI2_ARBITER_ENABLE    0x10000000
+
+#define HRCWH_CORE_DISABLE           0x08000000
+#define HRCWH_CORE_ENABLE            0x00000000
+
+#define HRCWH_FROM_0X00000100        0x00000000
+#define HRCWH_FROM_0XFFF00100        0x04000000
+
+#define HRCWH_BOOTSEQ_DISABLE        0x00000000
+#define HRCWH_BOOTSEQ_NORMAL         0x01000000
+#define HRCWH_BOOTSEQ_EXTENDED       0x02000000
+
+#define HRCWH_SW_WATCHDOG_DISABLE    0x00000000
+#define HRCWH_SW_WATCHDOG_ENABLE     0x00800000
+
+#define HRCWH_ROM_LOC_DDR_SDRAM      0x00000000
+#define HRCWH_ROM_LOC_PCI1           0x00100000
+#define HRCWH_ROM_LOC_PCI2           0x00200000
+#define HRCWH_ROM_LOC_LOCAL_8BIT     0x00500000
+#define HRCWH_ROM_LOC_LOCAL_16BIT    0x00600000
+#define HRCWH_ROM_LOC_LOCAL_32BIT    0x00700000
+
+#define HRCWH_TSEC1M_IN_RGMII        0x00000000
+#define HRCWH_TSEC1M_IN_RTBI         0x00004000
+#define HRCWH_TSEC1M_IN_GMII         0x00008000
+#define HRCWH_TSEC1M_IN_TBI          0x0000C000
+
+#define HRCWH_TSEC2M_IN_RGMII        0x00000000
+#define HRCWH_TSEC2M_IN_RTBI         0x00001000
+#define HRCWH_TSEC2M_IN_GMII         0x00002000
+#define HRCWH_TSEC2M_IN_TBI          0x00003000
+
+#define HRCWH_BIG_ENDIAN             0x00000000
+#define HRCWH_LITTLE_ENDIAN          0x00000008
+
+/*
+ * Hard Reset Configration Word - Low
+ */
+#define HRCWL_LCL_BUS_TO_SCB_CLK_1X1 0x00000000
+#define HRCWL_LCL_BUS_TO_SCB_CLK_2X1 0x80000000
+
+#define HRCWL_DDR_TO_SCB_CLK_1X1     0x00000000
+#define HRCWL_DDR_TO_SCB_CLK_2X1     0x40000000
+
+#define HRCWL_CSB_TO_CLKIN_16X1      0x00000000
+#define HRCWL_CSB_TO_CLKIN_1X1       0x01000000
+#define HRCWL_CSB_TO_CLKIN_2X1       0x02000000
+#define HRCWL_CSB_TO_CLKIN_3X1       0x03000000
+#define HRCWL_CSB_TO_CLKIN_4X1       0x04000000
+#define HRCWL_CSB_TO_CLKIN_5X1       0x05000000
+#define HRCWL_CSB_TO_CLKIN_6X1       0x06000000
+#define HRCWL_CSB_TO_CLKIN_7X1       0x07000000
+#define HRCWL_CSB_TO_CLKIN_8X1       0x08000000
+#define HRCWL_CSB_TO_CLKIN_9X1       0x09000000
+#define HRCWL_CSB_TO_CLKIN_10X1      0x0A000000
+#define HRCWL_CSB_TO_CLKIN_11X1      0x0B000000
+#define HRCWL_CSB_TO_CLKIN_12X1      0x0C000000
+#define HRCWL_CSB_TO_CLKIN_13X1      0x0D000000
+#define HRCWL_CSB_TO_CLKIN_14X1      0x0E000000
+#define HRCWL_CSB_TO_CLKIN_15X1      0x0F000000
+
+#define HRCWL_VCO_BYPASS             0x00000000
+#define HRCWL_VCO_1X2                0x00000000
+#define HRCWL_VCO_1X4                0x00200000
+#define HRCWL_VCO_1X8                0x00400000
+
+#define HRCWL_CORE_TO_CSB_BYPASS     0x00000000
+#define HRCWL_CORE_TO_CSB_1X1        0x00020000
+#define HRCWL_CORE_TO_CSB_1_5X1      0x00030000
+#define HRCWL_CORE_TO_CSB_2X1        0x00040000
+#define HRCWL_CORE_TO_CSB_2_5X1      0x00050000
+#define HRCWL_CORE_TO_CSB_3X1        0x00060000
+
+/*
+ * LCRR - Clock Ratio Register (10.3.1.16)
+ */
+#define LCRR_DBYP      0x80000000
+#define LCRR_DBYP_SHIFT        31
+#define LCRR_BUFCMDC   0x30000000
+#define LCRR_BUFCMDC_1 0x10000000
+#define LCRR_BUFCMDC_2 0x20000000
+#define LCRR_BUFCMDC_3 0x30000000
+#define LCRR_BUFCMDC_4 0x00000000
+#define LCRR_BUFCMDC_SHIFT     28
+#define LCRR_ECL       0x03000000
+#define LCRR_ECL_4     0x00000000
+#define LCRR_ECL_5     0x01000000
+#define LCRR_ECL_6     0x02000000
+#define LCRR_ECL_7     0x03000000
+#define LCRR_ECL_SHIFT         24
+#define LCRR_EADC      0x00030000
+#define LCRR_EADC_1    0x00010000
+#define LCRR_EADC_2    0x00020000
+#define LCRR_EADC_3    0x00030000
+#define LCRR_EADC_4    0x00000000
+#define LCRR_EADC_SHIFT        16
+#define LCRR_CLKDIV    0x0000000F
+#define LCRR_CLKDIV_2  0x00000002
+#define LCRR_CLKDIV_4  0x00000004
+#define LCRR_CLKDIV_8  0x00000008
+#define LCRR_CLKDIV_SHIFT       0
+
+#endif	/* __MPC83XX_H__ */
diff --git a/include/net.h b/include/net.h
index e50c3819b..623d22508 100644
--- a/include/net.h
+++ b/include/net.h
@@ -29,7 +29,7 @@
 # endif
 #endif	/* CONFIG_MPC5xxx */
 
-#if !defined(CONFIG_NET_MULTI) && (defined(CONFIG_8260) || defined(CONFIG_MPC8560))
+#if !defined(CONFIG_NET_MULTI) && defined(CONFIG_CPM2)
 #include <config.h>
 #if defined(CONFIG_ETHER_ON_FCC)
 #if defined(CONFIG_ETHER_ON_SCC)
diff --git a/include/spd.h b/include/spd.h
index 1ad4d801f..54b60d168 100644
--- a/include/spd.h
+++ b/include/spd.h
@@ -25,54 +25,82 @@
 #define _SPD_H_
 
 typedef struct spd_eeprom_s {
-   unsigned char info_size;   /* # of bytes written into serial memory           */
-   unsigned char chip_size;   /* Total # of bytes of SPD memory device           */
-   unsigned char mem_type;    /* Fundamental memory type (FPM, EDO, SDRAM...)    */
-   unsigned char nrow_addr;   /* # of Row Addresses on this assembly             */
-   unsigned char ncol_addr;   /* # of Column Addresses on this assembly          */
-   unsigned char nrows;       /* # of Module Rows on this assembly               */
-   unsigned char dataw_lsb;   /* Data Width of this assembly                     */
-   unsigned char dataw_msb;   /* ... Data Width continuation                     */
-   unsigned char voltage;     /* Voltage interface standard of this assembly     */
-   unsigned char clk_cycle;   /* SDRAM Cycle time at CL=X                        */
-   unsigned char clk_access;  /* SDRAM Access from Clock at CL=X                 */
-   unsigned char config;      /* DIMM Configuration type (non-parity, ECC)       */
-   unsigned char refresh;     /* Refresh Rate/Type                               */
-   unsigned char primw;       /* Primary SDRAM Width                             */
-   unsigned char ecw;         /* Error Checking SDRAM width                      */
-   unsigned char min_delay;   /* Min Clock Delay for Back to Back Random Address */
-   unsigned char burstl;      /* Burst Lengths Supported                         */
-   unsigned char nbanks;      /* # of Banks on Each SDRAM Device                 */
-   unsigned char cas_lat;     /* CAS# Latencies Supported                        */
-   unsigned char cs_lat;      /* CS# Latency                                     */
-   unsigned char write_lat;   /* Write Latency (also called Write Recovery time) */
-   unsigned char mod_attr;    /* SDRAM Module Attributes                         */
-   unsigned char dev_attr;    /* SDRAM Device Attributes                         */
-   unsigned char clk_cycle2;  /* Min SDRAM Cycle time at CL=X-1                  */
-   unsigned char clk_access2; /* SDRAM Access from Clock at CL=X-1               */
-   unsigned char clk_cycle3;  /* Min SDRAM Cycle time at CL=X-2                  */
-   unsigned char clk_access3; /* Max SDRAM Access from Clock at CL=X-2           */
-   unsigned char trp;         /* Min Row Precharge Time (tRP)                    */
-   unsigned char trrd;        /* Min Row Active to Row Active (tRRD)             */
-   unsigned char trcd;        /* Min RAS to CAS Delay (tRCD)                     */
-   unsigned char tras;        /* Minimum RAS Pulse Width (tRAS)                  */
-   unsigned char row_dens;    /* Density of each row on module                   */
-   unsigned char ca_setup;    /* Command and Address signal input setup time     */
-   unsigned char ca_hold;     /* Command and Address signal input hold time      */
-   unsigned char data_setup;  /* Data signal input setup time                    */
-   unsigned char data_hold;   /* Data signal input hold time                     */
-   unsigned char sset[26];    /* Superset Information (may be used in future)    */
-   unsigned char spd_rev;     /* SPD Data Revision Code                          */
-   unsigned char cksum;       /* Checksum for bytes 0-62                         */
-   unsigned char mid[8];      /* Manufacturer's JEDEC ID code per JEP-108E       */
-   unsigned char mloc;        /* Manufacturing Location                          */
-   unsigned char mpart[18];   /* Manufacturer's Part Number                      */
-   unsigned char rev[2];      /* Revision Code                                   */
-   unsigned char mdate[2];    /* Manufacturing Date                              */
-   unsigned char sernum[4];   /* Assembly Serial Number                          */
-   unsigned char mspec[27];   /* Manufacturer Specific Data                      */
-   unsigned char freq;        /* Intel specification frequency                   */
-   unsigned char intel_cas;   /* Intel Specification CAS# Latency support        */
+	unsigned char info_size;   /*  0 # bytes written into serial memory */
+	unsigned char chip_size;   /*  1 Total # bytes of SPD memory device */
+	unsigned char mem_type;    /*  2 Fundamental memory type */
+	unsigned char nrow_addr;   /*  3 # of Row Addresses on this assembly */
+	unsigned char ncol_addr;   /*  4 # of Column Addrs on this assembly */
+	unsigned char nrows;       /*  5 # of Module Rows on this assembly */
+	unsigned char dataw_lsb;   /*  6 Data Width of this assembly */
+	unsigned char dataw_msb;   /*  7 ... Data Width continuation */
+	unsigned char voltage;     /*  8 Voltage intf std of this assembly */
+	unsigned char clk_cycle;   /*  9 SDRAM Cycle time at CL=X */
+	unsigned char clk_access;  /* 10 SDRAM Access from Clock at CL=X */
+	unsigned char config;      /* 11 DIMM Configuration type */
+	unsigned char refresh;     /* 12 Refresh Rate/Type */
+	unsigned char primw;       /* 13 Primary SDRAM Width */
+	unsigned char ecw;         /* 14 Error Checking SDRAM width */
+	unsigned char min_delay;   /* 15 for Back to Back Random Address */
+	unsigned char burstl;      /* 16 Burst Lengths Supported */
+	unsigned char nbanks;      /* 17 # of Banks on Each SDRAM Device */
+	unsigned char cas_lat;     /* 18 CAS# Latencies Supported */
+	unsigned char cs_lat;      /* 19 CS# Latency */
+	unsigned char write_lat;   /* 20 Write Latency (aka Write Recovery) */
+	unsigned char mod_attr;    /* 21 SDRAM Module Attributes */
+	unsigned char dev_attr;    /* 22 SDRAM Device Attributes */
+	unsigned char clk_cycle2;  /* 23 Min SDRAM Cycle time at CL=X-1 */
+	unsigned char clk_access2; /* 24 SDRAM Access from Clock at CL=X-1 */
+	unsigned char clk_cycle3;  /* 25 Min SDRAM Cycle time at CL=X-2 */
+	unsigned char clk_access3; /* 26 Max Access from Clock at CL=X-2 */
+	unsigned char trp;         /* 27 Min Row Precharge Time (tRP)*/
+	unsigned char trrd;        /* 28 Min Row Active to Row Active (tRRD) */
+	unsigned char trcd;        /* 29 Min RAS to CAS Delay (tRCD) */
+	unsigned char tras;        /* 30 Minimum RAS Pulse Width (tRAS) */
+	unsigned char row_dens;    /* 31 Density of each row on module */
+	unsigned char ca_setup;    /* 32 Cmd + Addr signal input setup time */
+	unsigned char ca_hold;     /* 33 Cmd and Addr signal input hold time */
+	unsigned char data_setup;  /* 34 Data signal input setup time */
+	unsigned char data_hold;   /* 35 Data signal input hold time */
+	unsigned char twr;         /* 36 Write Recovery time tWR */
+	unsigned char twtr;        /* 37 Int write to read delay tWTR */
+	unsigned char trtp;        /* 38 Int read to precharge delay tRTP */
+	unsigned char mem_probe;   /* 39 Mem analysis probe characteristics */
+	unsigned char trctrfc_ext; /* 40 Extensions to trc and trfc */
+	unsigned char trc;         /* 41 Min Active to Auto refresh time tRC */
+	unsigned char trfc;        /* 42 Min Auto to Active period tRFC */
+	unsigned char tckmax;      /* 43 Max device cycle time tCKmax */
+	unsigned char tdqsq;       /* 44 Max DQS to DQ skew */
+	unsigned char tqhs;        /* 45 Max Read DataHold skew tQHS */
+	unsigned char pll_relock;  /* 46 PLL Relock time */
+	unsigned char res[15];     /* 47-xx IDD in SPD and Reserved space */
+	unsigned char spd_rev;     /* 62 SPD Data Revision Code */
+	unsigned char cksum;       /* 63 Checksum for bytes 0-62 */
+	unsigned char mid[8];      /* 64 Mfr's JEDEC ID code per JEP-108E */
+	unsigned char mloc;        /* 72 Manufacturing Location */
+	unsigned char mpart[18];   /* 73 Manufacturer's Part Number */
+	unsigned char rev[2];      /* 91 Revision Code */
+	unsigned char mdate[2];    /* 93 Manufacturing Date */
+	unsigned char sernum[4];   /* 95 Assembly Serial Number */
+	unsigned char mspec[27];   /* 99 Manufacturer Specific Data */
+
+	/*
+	 * Open for Customer Use starting with byte 128.
+	 */
+	unsigned char freq;        /* 128 Intel spec: frequency */
+	unsigned char intel_cas;   /* 129 Intel spec: CAS# Latency support */
 } spd_eeprom_t;
 
+
+/*
+ * Byte 2 Fundamental Memory Types.
+ */
+#define SPD_MEMTYPE_FPM		(0x01)
+#define SPD_MEMTYPE_EDO		(0x02)
+#define SPD_MEMTYPE_PIPE_NIBBLE	(0x03)
+#define SPD_MEMTYPE_SDRAM	(0x04)
+#define SPD_MEMTYPE_ROM		(0x05)
+#define SPD_MEMTYPE_SGRAM	(0x06)
+#define SPD_MEMTYPE_DDR		(0x07)
+#define SPD_MEMTYPE_DDR2	(0x08)
+
 #endif /* _SPD_H_ */