diff options
Diffstat (limited to 'board')
-rw-r--r-- | board/davinci/dm6467evm/dm6467evm.c | 1 | ||||
-rw-r--r-- | board/ep8248/ep8248.c | 1 | ||||
-rw-r--r-- | board/espt/lowlevel_init.S | 10 | ||||
-rw-r--r-- | board/freescale/mpc8569mds/bcsr.h | 8 | ||||
-rw-r--r-- | board/freescale/mpc8569mds/law.c | 1 | ||||
-rw-r--r-- | board/freescale/mpc8569mds/mpc8569mds.c | 210 | ||||
-rw-r--r-- | board/freescale/mpc8569mds/tlb.c | 30 | ||||
-rw-r--r-- | board/freescale/mpc8572ds/mpc8572ds.c | 6 | ||||
-rw-r--r-- | board/freescale/p1_p2_rdb/ddr.c | 20 | ||||
-rw-r--r-- | board/freescale/p1_p2_rdb/pci.c | 4 | ||||
-rw-r--r-- | board/freescale/p2020ds/p2020ds.c | 6 | ||||
-rw-r--r-- | board/logicpd/imx27lite/Makefile | 1 | ||||
-rw-r--r-- | board/renesas/sh7785lcr/lowlevel_init.S | 107 | ||||
-rw-r--r-- | board/sbc8548/sbc8548.c | 4 | ||||
-rw-r--r-- | board/xes/xpedite5370/tlb.c | 13 |
15 files changed, 312 insertions, 110 deletions
diff --git a/board/davinci/dm6467evm/dm6467evm.c b/board/davinci/dm6467evm/dm6467evm.c index 960581824..ac3b28299 100644 --- a/board/davinci/dm6467evm/dm6467evm.c +++ b/board/davinci/dm6467evm/dm6467evm.c @@ -28,4 +28,3 @@ int board_init(void) return 0; } - diff --git a/board/ep8248/ep8248.c b/board/ep8248/ep8248.c index 57d39aa7e..590894371 100644 --- a/board/ep8248/ep8248.c +++ b/board/ep8248/ep8248.c @@ -268,4 +268,3 @@ void ft_board_setup(void *blob, bd_t *bd) ft_cpu_setup( blob, bd); } #endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */ - diff --git a/board/espt/lowlevel_init.S b/board/espt/lowlevel_init.S index 7d5d72e12..7f0686c53 100644 --- a/board/espt/lowlevel_init.S +++ b/board/espt/lowlevel_init.S @@ -72,15 +72,7 @@ lowlevel_init: /* set DDR-SDRAM dummy read */ write32 MMSEL_A, MMSEL_D - mov.l MMSEL_A, r0 - synco - mov.l @r0, r1 - synco - - mov.l CS0_A, r0 - synco - mov.l @r0, r1 - synco + write32 MMSEL_A, CS0_A /* set DDR-SDRAM bus/endian etc */ write32 MIM_U_A, MIM_U_D diff --git a/board/freescale/mpc8569mds/bcsr.h b/board/freescale/mpc8569mds/bcsr.h index c4738d734..091b69c8d 100644 --- a/board/freescale/mpc8569mds/bcsr.h +++ b/board/freescale/mpc8569mds/bcsr.h @@ -33,7 +33,8 @@ #define BCSR6_UPC1_POS_EN 0x40 #define BCSR6_UPC1_ADDR_EN 0x20 #define BCSR6_UPC1_DEV2 0x10 -#define BCSR6_SD_ENABLE 0x04 +#define BCSR6_SD_CARD_1BIT 0x08 +#define BCSR6_SD_CARD_4BITS 0x04 #define BCSR6_TDM2G_EN 0x02 #define BCSR6_UCC7_RMII_EN 0x01 @@ -67,9 +68,14 @@ #define BCSR15_SMII6_DIS 0x08 #define BCSR15_SMII8_DIS 0x04 +#define BCSR15_QEUART_EN 0x01 #define BCSR16_UPC1_DEV2 0x02 +#define BCSR17_nUSBEN 0x80 +#define BCSR17_nUSBLOWSPD 0x40 +#define BCSR17_USBVCC 0x20 +#define BCSR17_USBMODE 0x10 #define BCSR17_FLASH_nWP 0x01 /*BCSR Utils functions*/ diff --git a/board/freescale/mpc8569mds/law.c b/board/freescale/mpc8569mds/law.c index e7381aae6..60eea45a8 100644 --- a/board/freescale/mpc8569mds/law.c +++ b/board/freescale/mpc8569mds/law.c @@ -54,6 +54,7 @@ struct law_entry law_table[] = { SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_1), SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_1), SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_128M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_SRIO_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_RIO), }; int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c index cc8873117..cdd781301 100644 --- a/board/freescale/mpc8569mds/mpc8569mds.c +++ b/board/freescale/mpc8569mds/mpc8569mds.c @@ -23,6 +23,7 @@ */ #include <common.h> +#include <hwconfig.h> #include <pci.h> #include <asm/processor.h> #include <asm/mmu.h> @@ -35,6 +36,7 @@ #include <ioports.h> #include <libfdt.h> #include <fdt_support.h> +#include <fsl_esdhc.h> #include "bcsr.h" @@ -152,6 +154,27 @@ const qe_iop_conf_t qe_iop_conf_tab[] = { {5, 10, 2, 0, 3}, /* UART1_CTS_B */ {5, 11, 1, 0, 2}, /* UART1_RTS_B */ + /* QE UART */ + {0, 19, 1, 0, 2}, /* QEUART_TX */ + {1, 17, 2, 0, 3}, /* QEUART_RX */ + {0, 25, 1, 0, 1}, /* QEUART_RTS */ + {1, 23, 2, 0, 1}, /* QEUART_CTS */ + + /* QE USB */ + {5, 3, 1, 0, 1}, /* USB_OE */ + {5, 4, 1, 0, 2}, /* USB_TP */ + {5, 5, 1, 0, 2}, /* USB_TN */ + {5, 6, 2, 0, 2}, /* USB_RP */ + {5, 7, 2, 0, 1}, /* USB_RX */ + {5, 8, 2, 0, 1}, /* USB_RN */ + {2, 4, 2, 0, 2}, /* CLK5 */ + + /* SPI Flash, M25P40 */ + {4, 27, 3, 0, 1}, /* SPI_MOSI */ + {4, 28, 3, 0, 1}, /* SPI_MISO */ + {4, 29, 3, 0, 1}, /* SPI_CLK */ + {4, 30, 1, 0, 0}, /* SPI_SEL, GPIO */ + {0, 0, 0, 0, QE_IOP_TAB_END} /* END of table */ }; @@ -303,6 +326,190 @@ local_bus_init(void) out_be32(&lbc->lcrr, (u32)in_be32(&lbc->lcrr)| 0x00030000); } +static void fdt_board_disable_serial(void *blob, bd_t *bd, const char *alias) +{ + const char *status = "disabled"; + int off; + int err; + + off = fdt_path_offset(blob, alias); + if (off < 0) { + printf("WARNING: could not find %s alias: %s.\n", alias, + fdt_strerror(off)); + return; + } + + err = fdt_setprop(blob, off, "status", status, strlen(status) + 1); + if (err) { + printf("WARNING: could not set status for serial0: %s.\n", + fdt_strerror(err)); + return; + } +} + +/* + * Because of an erratum in prototype boards it is impossible to use eSDHC + * without disabling UART0 (which makes it quite easy to 'brick' the board + * by simply issung 'setenv hwconfig esdhc', and not able to interact with + * U-Boot anylonger). + * + * So, but default we assume that the board is a prototype, which is a most + * safe assumption. There is no way to determine board revision from a + * register, so we use hwconfig. + */ + +static int prototype_board(void) +{ + if (hwconfig_subarg("board", "rev", NULL)) + return hwconfig_subarg_cmp("board", "rev", "prototype"); + return 1; +} + +static int esdhc_disables_uart0(void) +{ + return prototype_board() || + hwconfig_subarg_cmp("esdhc", "mode", "4-bits"); +} + +static void fdt_board_fixup_qe_uart(void *blob, bd_t *bd) +{ + u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE; + const char *devtype = "serial"; + const char *compat = "ucc_uart"; + const char *clk = "brg9"; + u32 portnum = 0; + int off = -1; + + if (!hwconfig("qe_uart")) + return; + + if (hwconfig("esdhc") && esdhc_disables_uart0()) { + printf("QE UART: won't enable with esdhc.\n"); + return; + } + + fdt_board_disable_serial(blob, bd, "serial1"); + + while (1) { + const u32 *idx; + int len; + + off = fdt_node_offset_by_compatible(blob, off, "ucc_geth"); + if (off < 0) { + printf("WARNING: unable to fixup device tree for " + "QE UART\n"); + return; + } + + idx = fdt_getprop(blob, off, "cell-index", &len); + if (!idx || len != sizeof(*idx) || *idx != fdt32_to_cpu(2)) + continue; + break; + } + + fdt_setprop(blob, off, "device_type", devtype, strlen(devtype) + 1); + fdt_setprop(blob, off, "compatible", compat, strlen(compat) + 1); + fdt_setprop(blob, off, "tx-clock-name", clk, strlen(clk) + 1); + fdt_setprop(blob, off, "rx-clock-name", clk, strlen(clk) + 1); + fdt_setprop(blob, off, "port-number", &portnum, sizeof(portnum)); + + setbits_8(&bcsr[15], BCSR15_QEUART_EN); +} + +#ifdef CONFIG_FSL_ESDHC + +int board_mmc_init(bd_t *bd) +{ + struct ccsr_gur *gur = (struct ccsr_gur *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE; + u8 bcsr6 = BCSR6_SD_CARD_1BIT; + + if (!hwconfig("esdhc")) + return 0; + + printf("Enabling eSDHC...\n" + " For eSDHC to function, I2C2 "); + if (esdhc_disables_uart0()) { + printf("and UART0 should be disabled.\n"); + printf(" Redirecting stderr, stdout and stdin to UART1...\n"); + console_assign(stderr, "eserial1"); + console_assign(stdout, "eserial1"); + console_assign(stdin, "eserial1"); + printf("Switched to UART1 (initial log has been printed to " + "UART0).\n"); + bcsr6 |= BCSR6_SD_CARD_4BITS; + } else { + printf("should be disabled.\n"); + } + + /* Assign I2C2 signals to eSDHC. */ + clrsetbits_be32(&gur->plppar1, PLPPAR1_I2C_BIT_MASK, + PLPPAR1_ESDHC_VAL); + clrsetbits_be32(&gur->plpdir1, PLPDIR1_I2C_BIT_MASK, + PLPDIR1_ESDHC_VAL); + + /* Mux I2C2 (and optionally UART0) signals to eSDHC. */ + setbits_8(&bcsr[6], bcsr6); + + return fsl_esdhc_mmc_init(bd); +} + +static void fdt_board_fixup_esdhc(void *blob, bd_t *bd) +{ + const char *status = "disabled"; + int off = -1; + + if (!hwconfig("esdhc")) + return; + + if (esdhc_disables_uart0()) + fdt_board_disable_serial(blob, bd, "serial0"); + + while (1) { + const u32 *idx; + int len; + + off = fdt_node_offset_by_compatible(blob, off, "fsl-i2c"); + if (off < 0) + break; + + idx = fdt_getprop(blob, off, "cell-index", &len); + if (!idx || len != sizeof(*idx)) + continue; + + if (*idx == 1) { + fdt_setprop(blob, off, "status", status, + strlen(status) + 1); + break; + } + } +} +#else +static inline void fdt_board_fixup_esdhc(void *blob, bd_t *bd) {} +#endif + +static void fdt_board_fixup_qe_usb(void *blob, bd_t *bd) +{ + u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE; + + if (hwconfig_subarg_cmp("qe_usb", "speed", "low")) + clrbits_8(&bcsr[17], BCSR17_nUSBLOWSPD); + else + setbits_8(&bcsr[17], BCSR17_nUSBLOWSPD); + + if (hwconfig_subarg_cmp("qe_usb", "mode", "peripheral")) { + clrbits_8(&bcsr[17], BCSR17_USBVCC); + clrbits_8(&bcsr[17], BCSR17_USBMODE); + do_fixup_by_compat(blob, "fsl,mpc8569-qe-usb", "mode", + "peripheral", sizeof("peripheral"), 1); + } else { + setbits_8(&bcsr[17], BCSR17_USBVCC); + setbits_8(&bcsr[17], BCSR17_USBMODE); + } + + clrbits_8(&bcsr[17], BCSR17_nUSBEN); +} + #ifdef CONFIG_PCIE1 static struct pci_controller pcie1_hose; #endif /* CONFIG_PCIE1 */ @@ -444,5 +651,8 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_PCIE1 ft_fsl_pci_setup(blob, "pci1", &pcie1_hose); #endif + fdt_board_fixup_esdhc(blob, bd); + fdt_board_fixup_qe_uart(blob, bd); + fdt_board_fixup_qe_usb(blob, bd); } #endif diff --git a/board/freescale/mpc8569mds/tlb.c b/board/freescale/mpc8569mds/tlb.c index d3b251e79..3b8ee050d 100644 --- a/board/freescale/mpc8569mds/tlb.c +++ b/board/freescale/mpc8569mds/tlb.c @@ -46,22 +46,24 @@ struct fsl_e_tlb_entry tlb_table[] = { /* TLB 1 Initializations */ /* - * TLBe 0: 16M Non-cacheable, guarded - * 0xff000000 16M FLASH (upper half) + * TLBe 0: 64M Non-cacheable, guarded * Out of reset this entry is only 4K. + * 0xfc000000 256K NAND FLASH (CS3) + * 0xfe000000 32M NOR FLASH (CS0) */ - SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE + 0x1000000, - CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000, + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_16M, 1), + 0, 0, BOOKE_PAGESZ_64M, 1), /* - * TLBe 1: 16M Non-cacheable, guarded - * 0xfe000000 16M FLASH (lower half) + * TLBe 1: 256KB Non-cacheable, guarded + * 0xf8000000 32K BCSR + * 0xf8008000 32K PIB (CS4) + * 0xf8010000 32K PIB (CS5) */ - SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 1, BOOKE_PAGESZ_16M, 1), + 0, 1, BOOKE_PAGESZ_256K, 1), /* * TLBe 2: 256M Non-cacheable, guarded @@ -88,16 +90,6 @@ struct fsl_e_tlb_entry tlb_table[] = { SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 4, BOOKE_PAGESZ_64M, 1), - - /* - * TLBe 5: 256K Non-cacheable, guarded - * 0xf8000000 32K BCSR - * 0xf8008000 32K PIB (CS4) - * 0xf8010000 32K PIB (CS5) - */ - SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 5, BOOKE_PAGESZ_256K, 1), }; int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/freescale/mpc8572ds/mpc8572ds.c b/board/freescale/mpc8572ds/mpc8572ds.c index 933dd127e..2b3223453 100644 --- a/board/freescale/mpc8572ds/mpc8572ds.c +++ b/board/freescale/mpc8572ds/mpc8572ds.c @@ -199,7 +199,7 @@ void pci_init_board(void) pcie_ep ? "End Point" : "Root Complex", pci_info[num].regs); first_free_busno = fsl_pci_init_port(&pci_info[num++], - &pcie3_hose, first_free_busno); + &pcie3_hose, first_free_busno, pcie_ep); /* * Activate ULI1575 legacy chip by performing a fake * memory access. Needed to make ULI RTC work. @@ -231,7 +231,7 @@ void pci_init_board(void) pcie_ep ? "End Point" : "Root Complex", pci_info[num].regs); first_free_busno = fsl_pci_init_port(&pci_info[num++], - &pcie2_hose, first_free_busno); + &pcie2_hose, first_free_busno, pcie_ep); } else { printf (" PCIE2: disabled\n"); } @@ -251,7 +251,7 @@ void pci_init_board(void) pcie_ep ? "End Point" : "Root Complex", pci_info[num].regs); first_free_busno = fsl_pci_init_port(&pci_info[num++], - &pcie1_hose, first_free_busno); + &pcie1_hose, first_free_busno, pcie_ep); } else { printf (" PCIE1: disabled\n"); } diff --git a/board/freescale/p1_p2_rdb/ddr.c b/board/freescale/p1_p2_rdb/ddr.c index 37c4b0a3b..fccc4f8f5 100644 --- a/board/freescale/p1_p2_rdb/ddr.c +++ b/board/freescale/p1_p2_rdb/ddr.c @@ -85,8 +85,8 @@ extern void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, #define CONFIG_SYS_DDR_TIMING_0_800 0x55770802 #define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b6543 #define CONFIG_SYS_DDR_TIMING_2_800 0x0fa074d1 -#define CONFIG_SYS_DDR_CLK_CTRL_800 0x02000000 -#define CONFIG_SYS_DDR_MODE_1_800 0x00440862 +#define CONFIG_SYS_DDR_CLK_CTRL_800 0x02800000 +#define CONFIG_SYS_DDR_MODE_1_800 0x00040852 #define CONFIG_SYS_DDR_MODE_2_800 0x00000000 #define CONFIG_SYS_DDR_INTERVAL_800 0x0a280100 @@ -206,7 +206,7 @@ phys_size_t fixed_sdram (void) { sys_info_t sysinfo; char buf[32]; - fsl_ddr_cfg_regs_t *ddr_cfg_regs = NULL; + fsl_ddr_cfg_regs_t ddr_cfg_regs; size_t ddr_size; struct cpu_type *cpu; @@ -215,13 +215,13 @@ phys_size_t fixed_sdram (void) strmhz(buf, sysinfo.freqDDRBus)); if(sysinfo.freqDDRBus <= DATARATE_400MHZ) - ddr_cfg_regs = &ddr_cfg_regs_400; + memcpy(&ddr_cfg_regs, &ddr_cfg_regs_400, sizeof(ddr_cfg_regs)); else if(sysinfo.freqDDRBus <= DATARATE_533MHZ) - ddr_cfg_regs = &ddr_cfg_regs_533; + memcpy(&ddr_cfg_regs, &ddr_cfg_regs_533, sizeof(ddr_cfg_regs)); else if(sysinfo.freqDDRBus <= DATARATE_667MHZ) - ddr_cfg_regs = &ddr_cfg_regs_667; + memcpy(&ddr_cfg_regs, &ddr_cfg_regs_667, sizeof(ddr_cfg_regs)); else if(sysinfo.freqDDRBus <= DATARATE_800MHZ) - ddr_cfg_regs = &ddr_cfg_regs_800; + memcpy(&ddr_cfg_regs, &ddr_cfg_regs_800, sizeof(ddr_cfg_regs)); else panic("Unsupported DDR data rate %s MT/s data rate\n", strmhz(buf, sysinfo.freqDDRBus)); @@ -230,14 +230,14 @@ phys_size_t fixed_sdram (void) /* P1020 and it's derivatives support max 32bit DDR width */ if(cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1020_E || cpu->soc_ver == SVR_P1011 || cpu->soc_ver == SVR_P1011_E) { - ddr_cfg_regs->ddr_sdram_cfg |= SDRAM_CFG_32_BE; - ddr_cfg_regs->cs[0].bnds = 0x0000001F; + ddr_cfg_regs.ddr_sdram_cfg |= SDRAM_CFG_32_BE; + ddr_cfg_regs.cs[0].bnds = 0x0000001F; ddr_size = (CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 / 2); } else ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; - fsl_ddr_set_memctl_regs(ddr_cfg_regs, 0); + fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0); return ddr_size; } diff --git a/board/freescale/p1_p2_rdb/pci.c b/board/freescale/p1_p2_rdb/pci.c index 4c08f9efa..773659673 100644 --- a/board/freescale/p1_p2_rdb/pci.c +++ b/board/freescale/p1_p2_rdb/pci.c @@ -71,7 +71,7 @@ void pci_init_board(void) pcie_ep ? "End Point" : "Root Complex", pci_info[num].regs); first_free_busno = fsl_pci_init_port(&pci_info[num++], - &pcie2_hose, first_free_busno); + &pcie2_hose, first_free_busno, pcie_ep); } else { printf (" PCIE2: disabled\n"); } @@ -90,7 +90,7 @@ void pci_init_board(void) pcie_ep ? "End Point" : "Root Complex", pci_info[num].regs); first_free_busno = fsl_pci_init_port(&pci_info[num++], - &pcie1_hose, first_free_busno); + &pcie1_hose, first_free_busno, pcie_ep); } else { printf (" PCIE1: disabled\n"); } diff --git a/board/freescale/p2020ds/p2020ds.c b/board/freescale/p2020ds/p2020ds.c index e38c0145e..9878fba10 100644 --- a/board/freescale/p2020ds/p2020ds.c +++ b/board/freescale/p2020ds/p2020ds.c @@ -227,7 +227,7 @@ void pci_init_board(void) pcie_ep ? "End Point" : "Root Complex", pci_info[num].regs); first_free_busno = fsl_pci_init_port(&pci_info[num++], - &pcie2_hose, first_free_busno); + &pcie2_hose, first_free_busno, pcie_ep); /* * The workaround doesn't work on p2020 because the location @@ -267,7 +267,7 @@ void pci_init_board(void) pcie_ep ? "End Point" : "Root Complex", pci_info[num].regs); first_free_busno = fsl_pci_init_port(&pci_info[num++], - &pcie3_hose, first_free_busno); + &pcie3_hose, first_free_busno, pcie_ep); } else { printf(" PCIE3: disabled\n"); } @@ -286,7 +286,7 @@ void pci_init_board(void) pcie_ep ? "End Point" : "Root Complex", pci_info[num].regs); first_free_busno = fsl_pci_init_port(&pci_info[num++], - &pcie1_hose, first_free_busno); + &pcie1_hose, first_free_busno, pcie_ep); } else { printf(" PCIE1: disabled\n"); } diff --git a/board/logicpd/imx27lite/Makefile b/board/logicpd/imx27lite/Makefile index c404cef58..04dc8ae1f 100644 --- a/board/logicpd/imx27lite/Makefile +++ b/board/logicpd/imx27lite/Makefile @@ -48,4 +48,3 @@ include $(SRCTREE)/rules.mk sinclude $(obj).depend ######################################################################### - diff --git a/board/renesas/sh7785lcr/lowlevel_init.S b/board/renesas/sh7785lcr/lowlevel_init.S index 7faad95ff..40d9b08c7 100644 --- a/board/renesas/sh7785lcr/lowlevel_init.S +++ b/board/renesas/sh7785lcr/lowlevel_init.S @@ -178,60 +178,6 @@ lbsc_end: .align 4 -/*------- LBSC -------*/ -MMSELR_A: .long 0xfc400020 -#if defined(CONFIG_SH_32BIT) -MMSELR_D: .long 0xa5a50005 -#else -MMSELR_D: .long 0xa5a50002 -#endif - -/*------- DBSC2 -------*/ -#define DBSC2_BASE 0xfe800000 -DBSC2_DBSTATE_A: .long DBSC2_BASE + 0x0c -DBSC2_DBEN_A: .long DBSC2_BASE + 0x10 -DBSC2_DBCMDCNT_A: .long DBSC2_BASE + 0x14 -DBSC2_DBCONF_A: .long DBSC2_BASE + 0x20 -DBSC2_DBTR0_A: .long DBSC2_BASE + 0x30 -DBSC2_DBTR1_A: .long DBSC2_BASE + 0x34 -DBSC2_DBTR2_A: .long DBSC2_BASE + 0x38 -DBSC2_DBRFCNT0_A: .long DBSC2_BASE + 0x40 -DBSC2_DBRFCNT1_A: .long DBSC2_BASE + 0x44 -DBSC2_DBRFCNT2_A: .long DBSC2_BASE + 0x48 -DBSC2_DBRFSTS_A: .long DBSC2_BASE + 0x4c -DBSC2_DBFREQ_A: .long DBSC2_BASE + 0x50 -DBSC2_DBDICODTOCD_A: .long DBSC2_BASE + 0x54 -DBSC2_DBMRCNT_A: .long DBSC2_BASE + 0x60 -DDR_DUMMY_ACCESS_A: .long 0x40000000 - -DBSC2_DBCONF_D: .long 0x00630002 -DBSC2_DBTR0_D: .long 0x050b1f04 -DBSC2_DBTR1_D: .long 0x00040204 -DBSC2_DBTR2_D: .long 0x02100308 -DBSC2_DBFREQ_D1: .long 0x00000000 -DBSC2_DBFREQ_D2: .long 0x00000100 -DBSC2_DBDICODTOCD_D: .long 0x000f0907 - -DBSC2_DBCMDCNT_D_CKE_H: .long 0x00000003 -DBSC2_DBCMDCNT_D_PALL: .long 0x00000002 -DBSC2_DBCMDCNT_D_REF: .long 0x00000004 - -DBSC2_DBMRCNT_D_EMRS2: .long 0x00020000 -DBSC2_DBMRCNT_D_EMRS3: .long 0x00030000 -DBSC2_DBMRCNT_D_EMRS1_1: .long 0x00010006 -DBSC2_DBMRCNT_D_EMRS1_2: .long 0x00010386 -DBSC2_DBMRCNT_D_MRS_1: .long 0x00000952 -DBSC2_DBMRCNT_D_MRS_2: .long 0x00000852 - -DBSC2_DBEN_D: .long 0x00000001 - -DBSC2_DBPDCNT0_D3: .long 0x00000080 -DBSC2_DBRFCNT1_D: .long 0x00000926 -DBSC2_DBRFCNT2_D: .long 0x00fe00fe -DBSC2_DBRFCNT0_D: .long 0x00010000 - -WAIT_200US: .long 33333 - /*------- GPIO -------*/ PACR_D: .long 0x0000 PBCR_D: .long 0x0000 @@ -291,6 +237,59 @@ PPUPR2_A: .long GPIO_BASE + 0x62 P1MSELR_A: .long GPIO_BASE + 0x80 P2MSELR_A: .long GPIO_BASE + 0x82 +MMSELR_A: .long 0xfc400020 +#if defined(CONFIG_SH_32BIT) +MMSELR_D: .long 0xa5a50005 +#else +MMSELR_D: .long 0xa5a50002 +#endif + +/*------- DBSC2 -------*/ +#define DBSC2_BASE 0xfe800000 +DBSC2_DBSTATE_A: .long DBSC2_BASE + 0x0c +DBSC2_DBEN_A: .long DBSC2_BASE + 0x10 +DBSC2_DBCMDCNT_A: .long DBSC2_BASE + 0x14 +DBSC2_DBCONF_A: .long DBSC2_BASE + 0x20 +DBSC2_DBTR0_A: .long DBSC2_BASE + 0x30 +DBSC2_DBTR1_A: .long DBSC2_BASE + 0x34 +DBSC2_DBTR2_A: .long DBSC2_BASE + 0x38 +DBSC2_DBRFCNT0_A: .long DBSC2_BASE + 0x40 +DBSC2_DBRFCNT1_A: .long DBSC2_BASE + 0x44 +DBSC2_DBRFCNT2_A: .long DBSC2_BASE + 0x48 +DBSC2_DBRFSTS_A: .long DBSC2_BASE + 0x4c +DBSC2_DBFREQ_A: .long DBSC2_BASE + 0x50 +DBSC2_DBDICODTOCD_A:.long DBSC2_BASE + 0x54 +DBSC2_DBMRCNT_A: .long DBSC2_BASE + 0x60 +DDR_DUMMY_ACCESS_A: .long 0x40000000 + +DBSC2_DBCONF_D: .long 0x00630002 +DBSC2_DBTR0_D: .long 0x050b1f04 +DBSC2_DBTR1_D: .long 0x00040204 +DBSC2_DBTR2_D: .long 0x02100308 +DBSC2_DBFREQ_D1: .long 0x00000000 +DBSC2_DBFREQ_D2: .long 0x00000100 +DBSC2_DBDICODTOCD_D:.long 0x000f0907 + +DBSC2_DBCMDCNT_D_CKE_H: .long 0x00000003 +DBSC2_DBCMDCNT_D_PALL: .long 0x00000002 +DBSC2_DBCMDCNT_D_REF: .long 0x00000004 + +DBSC2_DBMRCNT_D_EMRS2: .long 0x00020000 +DBSC2_DBMRCNT_D_EMRS3: .long 0x00030000 +DBSC2_DBMRCNT_D_EMRS1_1: .long 0x00010006 +DBSC2_DBMRCNT_D_EMRS1_2: .long 0x00010386 +DBSC2_DBMRCNT_D_MRS_1: .long 0x00000952 +DBSC2_DBMRCNT_D_MRS_2: .long 0x00000852 + +DBSC2_DBEN_D: .long 0x00000001 + +DBSC2_DBPDCNT0_D3: .long 0x00000080 +DBSC2_DBRFCNT1_D: .long 0x00000926 +DBSC2_DBRFCNT2_D: .long 0x00fe00fe +DBSC2_DBRFCNT0_D: .long 0x00010000 + +WAIT_200US: .long 33333 + /*------- LBSC -------*/ PASCR_A: .long 0xff000070 PASCR_32BIT_MODE: .long 0x80000000 /* check booting mode */ diff --git a/board/sbc8548/sbc8548.c b/board/sbc8548/sbc8548.c index 194f6ab96..5e3e17658 100644 --- a/board/sbc8548/sbc8548.c +++ b/board/sbc8548/sbc8548.c @@ -359,7 +359,7 @@ pci_init_board(void) SET_STD_PCI_INFO(pci_info[num], 1); first_free_busno = fsl_pci_init_port(&pci_info[num++], - &pci1_hose, first_free_busno); + &pci1_hose, first_free_busno, 0); } else { printf (" PCI: disabled\n"); } @@ -378,7 +378,7 @@ pci_init_board(void) SET_STD_PCIE_INFO(pci_info[num], 1); printf (" PCIE at base address %lx\n", pci_info[num].regs); first_free_busno = fsl_pci_init_port(&pci_info[num++], - &pcie1_hose, first_free_busno); + &pcie1_hose, first_free_busno, 0); } else { printf (" PCIE: disabled\n"); } diff --git a/board/xes/xpedite5370/tlb.c b/board/xes/xpedite5370/tlb.c index caafa3011..a465ce386 100644 --- a/board/xes/xpedite5370/tlb.c +++ b/board/xes/xpedite5370/tlb.c @@ -61,32 +61,37 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 2, BOOKE_PAGESZ_1M, 1), + /* **M** - Boot page for secondary processors */ + SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, CONFIG_BPTR_VIRT_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, + 0, 3, BOOKE_PAGESZ_4K, 1), + #ifdef CONFIG_PCIE1 /* *I*G* - PCIe */ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 3, BOOKE_PAGESZ_1G, 1), + 0, 4, BOOKE_PAGESZ_1G, 1), #endif #ifdef CONFIG_PCIE2 /* *I*G* - PCIe */ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 4, BOOKE_PAGESZ_256M, 1), + 0, 5, BOOKE_PAGESZ_256M, 1), #endif #ifdef CONFIG_PCIE3 /* *I*G* - PCIe */ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 5, BOOKE_PAGESZ_256M, 1), + 0, 6, BOOKE_PAGESZ_256M, 1), #endif #if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) /* *I*G* - PCIe */ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 6, BOOKE_PAGESZ_64M, 1), + 0, 7, BOOKE_PAGESZ_64M, 1), #endif }; |