diff options
Diffstat (limited to 'include/configs/ASH405.h')
| -rw-r--r-- | include/configs/ASH405.h | 43 |
1 files changed, 12 insertions, 31 deletions
diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h index 9e0ee371c..0718c8574 100644 --- a/include/configs/ASH405.h +++ b/include/configs/ASH405.h @@ -53,9 +53,13 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 + #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ @@ -144,39 +148,16 @@ * NAND-FLASH stuff *----------------------------------------------------------------------- */ +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE } +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_BIG_DELAY_US 25 -#define CFG_NAND_LEGACY - -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define SECTORSIZE 512 - -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 - -#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ - -#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0) -#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0) -#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0) -#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0) -#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0) -#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0) -#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY)) - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) +#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ +#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ +#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ +#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */ #define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ /*----------------------------------------------------------------------- |