diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/pcs440ep.h | 82 | ||||
| -rw-r--r-- | include/sha1.h | 115 | ||||
| -rw-r--r-- | include/status_led.h | 7 |
3 files changed, 201 insertions, 3 deletions
diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index 751b51277..0e83e4881 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -106,19 +106,26 @@ #ifdef CFG_ENV_IS_IN_FLASH #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +#define CONFIG_ENV_OVERWRITE 1 /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif /* CFG_ENV_IS_IN_FLASH */ +#define ENV_NAME_REVLEV "revision_level" +#define ENV_NAME_SOLDER "solder_switch" +#define ENV_NAME_DIP "dip" + /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ #undef CONFIG_DDR_ECC /* don't use ECC */ #define SPD_EEPROM_ADDRESS {0x50} +#define CONFIG_PROG_SDRAM_TLB 1 /*----------------------------------------------------------------------- * I2C @@ -143,6 +150,8 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "hostname=pcs440ep\0" \ + "use_eeprom_ethaddr=default\0" \ + "cs_test=off\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -173,6 +182,36 @@ #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #endif +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +/* check U-Boot image with SHA1 sum */ +#define CONFIG_SHA1_CHECK_UB_IMG 1 +#define CONFIG_SHA1_START CFG_MONITOR_BASE +#define CONFIG_SHA1_LEN CFG_MONITOR_LEN + +/*----------------------------------------------------------------------- + * Definitions for status LED + */ +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ +#define CONFIG_BOARD_SPECIFIC_LED 1 + +#define STATUS_LED_BIT 0x08 /* LED 1 is on GPIO_PPC_1 */ +#define STATUS_LED_PERIOD ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE STATUS_LED_OFF +#define STATUS_LED_BIT1 0x04 /* LED 2 is on GPIO_PPC_2 */ +#define STATUS_LED_PERIOD1 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE1 STATUS_LED_ON +#define STATUS_LED_BIT2 0x02 /* LED 3 is on GPIO_PPC_3 */ +#define STATUS_LED_PERIOD2 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE2 STATUS_LED_OFF +#define STATUS_LED_BIT3 0x01 /* LED 4 is on GPIO_PPC_4 */ +#define STATUS_LED_PERIOD3 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE3 STATUS_LED_OFF + +#define CONFIG_SHOW_BOOT_PROGRESS 1 + #define CONFIG_BAUDRATE 115200 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ @@ -214,7 +253,10 @@ CFG_CMD_DIAG | \ CFG_CMD_EEPROM | \ CFG_CMD_ELF | \ + CFG_CMD_EXT2 | \ + CFG_CMD_FAT | \ CFG_CMD_I2C | \ + CFG_CMD_IDE | \ CFG_CMD_IRQ | \ CFG_CMD_MII | \ CFG_CMD_NET | \ @@ -222,9 +264,8 @@ CFG_CMD_PCI | \ CFG_CMD_PING | \ CFG_CMD_REGINFO | \ + CFG_CMD_REISER | \ CFG_CMD_SDRAM | \ - CFG_CMD_EXT2 | \ - CFG_CMD_FAT | \ CFG_CMD_USB ) @@ -410,4 +451,39 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus */ + +#define CONFIG_IDE_PREINIT 1 +#define CONFIG_IDE_RESET 1 + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_CF1 + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET 0 + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET (0x0000) + +/* This addresses need to be shifted one place to the left + * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0) + * This values are shifted + */ +#define CFG_ATA_PORT_ADDR(port) ((port) << 1) + #endif /* __CONFIG_H */ diff --git a/include/sha1.h b/include/sha1.h new file mode 100644 index 000000000..3030f2975 --- /dev/null +++ b/include/sha1.h @@ -0,0 +1,115 @@ +/** + * \file sha1.h + * based from http://xyssl.org/code/source/sha1/ + * FIPS-180-1 compliant SHA-1 implementation + * + * Copyright (C) 2003-2006 Christophe Devine + * + * This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU Lesser General Public + * License, version 2.1 as published by the Free Software Foundation. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * Lesser General Public License for more details. + * + * You should have received a copy of the GNU Lesser General Public + * License along with this library; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ +/* + * The SHA-1 standard was published by NIST in 1993. + * + * http://www.itl.nist.gov/fipspubs/fip180-1.htm + */ +#ifndef _SHA1_H +#define _SHA1_H + +#ifdef __cplusplus +extern "C" { +#endif + +#define SHA1_SUM_POS -0x20 +#define SHA1_SUM_LEN 20 + +/** + * \brief SHA-1 context structure + */ +typedef struct +{ + unsigned long total[2]; /*!< number of bytes processed */ + unsigned long state[5]; /*!< intermediate digest state */ + unsigned char buffer[64]; /*!< data block being processed */ +} +sha1_context; + +/** + * \brief SHA-1 context setup + * + * \param ctx SHA-1 context to be initialized + */ +void sha1_starts( sha1_context *ctx ); + +/** + * \brief SHA-1 process buffer + * + * \param ctx SHA-1 context + * \param input buffer holding the data + * \param ilen length of the input data + */ +void sha1_update( sha1_context *ctx, unsigned char *input, int ilen ); + +/** + * \brief SHA-1 final digest + * + * \param ctx SHA-1 context + * \param output SHA-1 checksum result + */ +void sha1_finish( sha1_context *ctx, unsigned char output[20] ); + +/** + * \brief Output = SHA-1( input buffer ) + * + * \param input buffer holding the data + * \param ilen length of the input data + * \param output SHA-1 checksum result + */ +void sha1_csum( unsigned char *input, int ilen, + unsigned char output[20] ); + +/** + * \brief Output = SHA-1( file contents ) + * + * \param path input file name + * \param output SHA-1 checksum result + * \return 0 if successful, or 1 if fopen failed + */ +int sha1_file( char *path, unsigned char output[20] ); + +/** + * \brief Output = HMAC-SHA-1( input buffer, hmac key ) + * + * \param key HMAC secret key + * \param keylen length of the HMAC key + * \param input buffer holding the data + * \param ilen length of the input data + * \param output HMAC-SHA-1 result + */ +void sha1_hmac( unsigned char *key, int keylen, + unsigned char *input, int ilen, + unsigned char output[20] ); + +/** + * \brief Checkup routine + * + * \return 0 if successful, or 1 if the test failed + */ +int sha1_self_test( void ); + +#ifdef __cplusplus +} +#endif + +#endif /* sha1.h */ diff --git a/include/status_led.h b/include/status_led.h index 71a202fe3..a64681425 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -367,6 +367,13 @@ void status_led_set (int led, int state); #define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ +#elif defined(CONFIG_BOARD_SPECIFIC_LED) +/* led_id_t is unsigned long mask */ +typedef unsigned long led_id_t; + +extern void __led_toggle (led_id_t mask); +extern void __led_init (led_id_t mask, int state); +extern void __led_set (led_id_t mask, int state); #else # error Status LED configuration missing #endif |