| Age | Commit message (Collapse) | Author |
|---|
|
Some board ports place TEXT_BASE at a location that would cause the
RESET_VECTOR_ADDRESS not to be at 0xfffffffc when we link. By default
we assume RESET_VECTOR_ADDRESS will be 0xfffffffc if the board doesn't
explicitly set it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
|
|
There is no reason to do a run time check for e500 v1 based cores to
determine if we have the GUTs RSTCR facility. Only the first generation
of PQ3 parts (MPC8540/41/55/60) do not have it. So checking to see if
we are e500 v2 would miss future parts (like e500mc).
Just change this to be ifdef'd based on CONFIG_MPC85{40,41,55,60}.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
While in probecpu() UART is still not initialized.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Fixing the number of cores in the device tree based on the actual number of
cores on the system. With this same device tree image can be used for dual
core and single core members of otherwise exactly same SOC.
For example:
* P2020RDB and P2010RDB
* P1020RDB and P1011RDB
* MPC8641D and MPC8641
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Incase the system is detected with Unknown SVR, let the system boot
with a default value and a proper message.
Now with dynamic detection of SOC properties from SVR, this is necessary
to prevent a crash.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Refactor the code into a simple bitmask lookup table that determines if
a given PCI controller is enabled and if its in host/root-complex or
agent/end-point mode.
Each processor in the PQ3/MPC86xx family specified different encodings
for the cfg_host_agt[] and cfg_IO_ports[] boot strapping signals.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Cleaned up cpu/mpc85xx/Makefile to use CONFIG_* for those obvious cases
we have like PCI, CPM2, QE. Also reworked it to use one line per file
for everything and sorted in alphabetical order.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
After programming a new LAW, we should read-back the LAWAR register so that
we sync the writes. Otherwise, code that attempts to use the new LAW-mapped
memory might fail right away.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Its possible that we try and copy the boot page code out of flash into a
DDR location that doesn't have a TLB cover it. For example, if we have
3G of DDR we typically only map the first 2G. In the cases of 4G+ this
wasn't an issue since the reset page TLB mapping covered the last page
of memory which we wanted to copy to.
We now change the physical address of the reset page TLB to map to the
true physical location of the boot page code, copy and than set the
TLB back to its 1:1 mapping of the reset page.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Allow us to search the TLB array based on an address. This is useful
if we want to change an entry but dont know where it happens to be
located.
For example, the boot page mapping we use on MP or the flash TLB that
we change the WIMGE settings for after we've relocated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
In future Book-E implementations IVORs will most likely go away and be
replaced with fixed offsets. The IVPR will continue to exist to allow
for relocation of the interrupt vectors.
This code adds support to setup the IVORs as their fixed offset values
per the ISA 2.06 spec when we transition from u-boot to another OS
either via 'bootm' or a cpu release.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The ddr_pd_cntl isn't defined in any reference manual and thus we wil
remove especially since we set it to 0, which would most likely be its
POR value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Now that we have a pointer to the cpu struct we need to relocate it once
we get into ram.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The warning is bogus, so silence it by initializing the 'ret' variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Enable eSDHC Clock based on generic CONFIG_FSL_ESDHC define instead of a
platform define. This will enable all the 85xx platforms to use sdhc_clk
based on CONFIG_FSL_ESDHC.
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
|
|
|
The value of I2C_TIMEOUT in fsl_i2c.c has several problems. First, it is
defined as CONFIG_HZ/4, but it is used as a count of microseconds, so it makes
no sense to derive it from a clock rate. Second, the current value (250) is
too low for some boards, so it needs to be increased. Third, the timeout
necessary for multiple-master arbitration is larger than the timeout for basic
read/write operations, so we shouldn't have a single constant for both timeouts.
Finally, it would be nice if we could override these values on a per-board
basis.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Reset any i2c devices that may have been interrupted during a system reset.
Normally this would be accomplished by clocking the line until SCL and SDA
are released and then sending a start condtiion (From an Atmel datasheet).
There is no direct access to the i2c pins so instead create start commands
through the i2c interface. Send a start command then delay for the SDA Hold
time, repeat this by disabling/enabling the bus a total of 9 times.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
|
|
This patch adds support for the DM365 EVM.
It has been tested on a DM365 EVM.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
This patch adds support for DaVinci DM365 SOC.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
|
|
This patch adds support for the DevKit8000 board.
Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Rather than maintain/extend the current ifeq($(ARCH)) mess that exists in
the standalone Makefile, push the setting up of LOAD_ADDR out to the arch
config.mk (and rename to STANDALONE_LOAD_ADDR in the process). This keeps
the common code clean and lets the arch do whatever crazy crap it wants in
its own area.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Removed stdio.h inclusion and moved trace macros to use printf avoiding to
write debug informations to standard error.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
"All Rights Reserved" conflicts with the GPL.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
|
Some files included my old standerd file header which had a "All
Rights Reserved" part. As this has never been my intention, I remove
these lines to make the files compatible with GPL v.2 and later.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Fix warning messages:
cmd_mtdparts.c:1429: warning: format '%08lx' expects type 'long
unsigned int', but argument 6 has type 'u32'
cmd_mtdparts.c:1429: warning: format '%08lx' expects type 'long
unsigned int', but argument 7 has type 'u32'
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
This is needed so that we could use this macro for non-UBI code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
|
-fno-strict-aliasing is hidding warnings.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
-fno-strict-aliasing is hidding warnings.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
|
|
Added a arch_preboot_os() function that cpu specific code can implement to
allow for various modifications to the state of the machine right before
we boot. This can be useful to setup register state to a specific
configuration.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: André Schwarz <andre.schwarz@matrix-vision.de>
|
|
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
Now that the PCI, SATA et al compile problems have been resolved, the
cludge that was applied to avoid them can be removed
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
Primary intent is to resolve build errors for this board which has been
neglected for a very long time. I do not have one of these boards, so I
cannot test functionality
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
This patch is based on a patch submitted by Jean-Christophe PLAGNIOL-VILLARD
on 18th May 2008 as part of a general i386 / sc520 fixup which was never
applied
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
Removed do_pinit() - now declared in cmd_pcmcia.c
Added #define CONFIG_CMD_PCMCIA around pcmcia_off() in line with other
PCMCIA drivers
signed/unsigned type fixups
Added semi-colon after default: label as required by newer gcc
The only board that appears to use this driver is the sc520_spunk which
is very old and very likely very broken anyway. I do not have one to test
whether this patch breaks anything functionaly, I have can only check
that it compiles without warning or error
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
Cast first parameter to sata_cpy()
In /drivers/block/ata_piix.h, ata_id_has_lba48(), ata_id_has_lba(),
ata_id_has_dma(), ata_id_u32(), ata_id_u64() are all defined in
include/libata.h which is included in ata.h which is included by all files
which include ata_piix.h (only ata_piix.c) so these definitions are
supurflous to (and conlict with) this in libata.h. Interestingly, my
compiler complains about ata_id_u64 already being defined, but not
ata_id_u32
ata_dump_id() is defined in include/libata.h and should not be static
(maybe should even use ata_dump_id() in libata.c
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
Change PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY (Originally done in
commit ff4e66e93c1a, regressed by commit 6d7f610b09f8)
Cast PCI_ROM_ADDRESS_MASK to u32
Wrap probe_pci_video() call inside #ifdef CONFIG_VIDEO
Change call to pci_find_class() to pci_find_devices(). This is based on a
patch submitted on 1st March 2007 (Patch that fixes the compilation errors
for sc520_cdp board) by mushtaq_k
This patch requires that PCI_VIDEO_VENDOR_ID and PCI_VIDEO_DEVICE_ID be
specified in the board config file. Dummy values have been added for the
SC520 CDP board to enable compilation, but since I do not have one of these,
I do know what the values should be
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
The current implementation has the timer being started before the interrupt
handler is installed. It the interrupt occurs before the handler is
installed, the timer interrupt is never reset and the timer stops
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
