summaryrefslogtreecommitdiff
path: root/cpu/arm920t
AgeCommit message (Collapse)Author
2009-04-05arm: clean cache managementJean-Christophe PLAGNIOL-VILLARD
unify arm cache management except for non standard cache as ARM7TDMI Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-05arm: update co-processor 15 accessJean-Christophe PLAGNIOL-VILLARD
import system.h from linux Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04at91rm9200: Reset updateJean-Christophe PLAGNIOL-VILLARD
Update the rm9200 reset sequence to try executing a board-specific reset function and move specific board reset to board. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04at91rm9200: move serial shutdown code to serial driversJean-Christophe PLAGNIOL-VILLARD
introduce serial_exit for this purpose. Use it only when the rm9200 serial driver is active Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04at91rm9200: move serial driver to drivers/serialJean-Christophe PLAGNIOL-VILLARD
add CONFIG_AT91RM9200_USART to activate the driver Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04Add support for the AT91RM9200EK Board.Ulf Samuelsson
The AT91RM9200-EK Evaluation Board supports the AT91RM9200 ARM9-based 32-bit RISC microcontroller and enables real-time code development and evaluation. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507 with - NOR (cfi driver) - DataFlash - USB OHCI - Net - I2C (hard) Signed-off-by: Ulf Samuelsson <ulf@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-30s3c2410: move nand driver to drivers/mtd/nandJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-30s3c24x0: move i2c driver to drivers/i2cJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-30s3c24x0: move serial driver to drivers/serialJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-30imx: move serial driver to drivers/serialJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-29ks8695: move serial driver to drivers/serialJean-Christophe PLAGNIOL-VILLARD
add CONFIG_KS8695_SERIAL to activate the driver Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-20cpu/: get mac address from environmentMike Frysinger
The environment is the canonical storage location of the mac address, so we're killing off the global data location and moving everything to querying the env directly. The cpus that get converted here: at91rm9200 mpc512x mpc5xxx mpc8260 mpc8xx ppc4xx Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Ben Warren <biggerbadderben@gmail.com> CC: John Rigby <jrigby@freescale.com> CC: Stefan Roese <sr@denx.de>
2009-01-28usb.h: use standard __LITTLE_ENDIAN from Linux headersMike Frysinger
Rather than forcing people to define a custom "LITTLEENDIAN", just use the __LITTLE_ENDIAN one from the Linux byteorder headers that every arch is already setting up. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-01-06at91rm9200: move define from lowlevel_init to headerJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-06at91rm9200: rename lowlevel init value to CONFIG_SYS_Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-15i2c: merge all i2c_reg_read() and i2c_reg_write() into inline functionsTimur Tabi
All implementations of the functions i2c_reg_read() and i2c_reg_write() are identical. We can save space and simplify the code by converting these functions into inlines and putting them in i2c.h. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-13Remove compiler warning: target CPU does not support interworkingSergei Poselenov
This warning is issued by modern ARM-EABI GCC on non-thumb targets. Signed-off-by: Vladimir Panfilov <pvr@emcraft.com> Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
2008-12-02AT91: remove non supported board AT91RM9200DF macroJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-11-24AT91RM9200DK: fix broken boot from NOR flashWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-11-24at91rm9200: fix broken boot from nor flashJens Scharsig
This patch fix the broken boot from NOR Flash on AT91RM9200 boards, if CONFIG_AT91RM9200 is defined and nor preloader is used. Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
2008-10-21Merge git://git.denx.de/u-boot into x1Markus Klotzbuecher
Conflicts: drivers/usb/usb_ohci.c
2008-10-18rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-14The PIPE_INTERRUPT flag is used wrongRemy Bohmer
At a lot of places in the code the PIPE_INTERRUPT flags and friends are used wrong. The wrong bits are compared to this flag resulting in wrong conditions. Also there are macros that should be used for PIPE_* flags. This patch tries to fix them all, however, I was not able to test the changes, because I do not have any of these boards. Review required! Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Markus Klotzbuecher <mk@denx.de>
2008-09-12at91rm9200: fix errors with CONFIG_CMD_I2C_TREEJens Scharsig
This patch prevents linker error on AT91RM9200 boards, if CONFIG_CMD_I2_TREE is set. It implements i2c_set_bus_speed and i2c_get_bus_speed as a dummy function. Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
2008-09-12i.mx change get_timer(base) to return time since baseAndrew Dyer
This patch changes get_timer() for i.MX to return the time since 'base' instead of the time since the counter was at zero. Symptom seen is flash timeout errors when erasing or programming a sector using the common cfi flash code. Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
2008-09-12i.MX use u-boot baud rate and don't assume UART master clockAndrew Dyer
1) Change the i.MX serial driver to use the baud rate set in the u-boot environment 2) don't assume a 16MHz value for PERCLK1 in baud rate calculations 3) don't write a 1 to the RDR bit in the USR2 reg. (bit is not "write one to clear" like other status bits in the reg.) Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
2008-09-12arm920t fix constant error in start.SAndrew Dyer
Code in cpu/arm920t/start.S will die with a compilation error if CONFIG_STACKSIZE + CFG_MALLOC_LEN works out to an invalid constant for the ARM sub instruction. Change the code so that each is subtracted independently to avoid the error. Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
2008-08-14Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk
2008-08-13s3c24x0: Update NAND driver to new API.Scott Wood
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-13drivers/mtd/nand: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD
rename CFG_NAND_LEGACY to CONFIG_NAND_LEGACY Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-07-06Remove duplicate definitions in include/lxt971a.h.Hugo Villeneuve
Remove duplicate definitions in include/lxt971a.h. Remove duplicate registers and bits definitions in include/lxt971a.h for standard MII registers, and use values in include/miiphy.h instead. Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-05-21Big white-space cleanup.Wolfgang Denk
This commit gets rid of a huge amount of silly white-space issues. Especially, all sequences of SPACEs followed by TAB characters get removed (unless they appear in print statements). Also remove all embedded "vim:" and "vi:" statements which hide indentation problems. Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-09Fix some typosAdrian Filipi
This patch fixes three typos. The first is a repetition of CONFIG_CMD_BSP. The second makes the #endif comment match its #if. The third is a spelling error. Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
2008-04-25USB: fix more GCC 4.2.x aliasing warningsWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Markus Klotzbuecher <mk@denx.de>
2008-04-17Fix regression introduced by a typo in "Tidied other cpu/arm920t/start.S code"Guennadi Liakhovetski
Restore logic reverted by commit commit 80767a6cead9990d9e77e62be947843c2c72f469 Author: Peter Pearse <peter.pearse@arm.com> Date: Wed Sep 5 16:04:41 2007 +0100 Changed API name to coloured_led.h Removed code using deprecated ifdef CONFIG_BOOTBINFUNC Tidied other cpu/arm920t/start.S code Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-03-30use correct at91rm9200 register nameDavid Brownell
This fixes a naming bug for at91rm9200 lowlevel init code: NOR boot flash is on chipselect 0, not chipselect 2. This makes code use the register name from chip datasheets. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2008-02-17s3c24x0: Fix unused variable 'i' in function 'serial_init_dev'Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-02-14ARM: cleanup duplicated exception handlingcodeAndreas Engel
Move duplicated exception handling code into lib_arm. Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
2008-02-04ARM: S3C24x0 SoC NAND controller supportHarald Welte
This patch adds NAND support to the S3C24x0 SoC code in u-boot Signed-off-by: Harald Welte <laforge@openmoko.org>
2008-02-04ARM: s3c24xx: Multiple serial port supportHarald Welte
This patch adds support for CONFIG_SERIAL_MULTI on s3c24x0 CPU's Signed-off-by: Harald Welte <laforge@openmoko.org>
2008-02-04ARM: arm920t: Allow use of 'gd' pointer from IRQHarald Welte
This patch allows us to use the 'gd' pointer (and thus environment and everything else associated with it) from interrupt context on arm920t. Signed-off-by: Harald Welte <laforge@openmoko.org>
2008-02-04ARM: arm920/s3c24xx: IRQ demulitplexer callbackHarald Welte
This patch adds a IRQ demultiplexer callback to the arm920 cpu core code, plus a stub implementation of it for the S3C2410. The purpose is to allow arm920t implementations such as the s3c24x0 to implement interrupt handlers in u-boot without having to touch core arm920t code. Signed-off-by: Harald Welte <laforge@openmoko.org>
2007-11-18s3c24x0: Fix usb_ohci.c missing in MakefileJean-Christophe PLAGNIOL-VILLARD
and usb_ohci.c warning differ in signedness Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-10-24fix warning: no return statement in function returning non-voidJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-09-18Move coloured led API to status_led.hPeter Pearse
Improve indentation in drivers/at45.c
2007-09-11Final tidyPeter Pearse
2007-09-05Changed API name to coloured_led.hPeter Pearse
Removed code using deprecated ifdef CONFIG_BOOTBINFUNC Tidied other cpu/arm920t/start.S code
2007-09-04Add coloured led interface for ARM boards.Peter Pearse
Use it in cpu/arm920t/start.S to indicate U-Boot code has been entered.
2007-08-14Coding style cleanup. Update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-08-14Add the files.Peter Pearse
generated by cgit v1.2.3 (git 2.39.1) at 2024-06-30 09:42:47 +0000