| Age | Commit message (Collapse) | Author |
|---|
|
The MPC83xx family never have CPM block, so remove it from 83xx.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
This reverts commit 70431e8a7393b6b793f77957f95b999fc9a269b8 which has
proven problematic getting right from the start at least on 83xx and
4xx.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
32-bit wide ECC memory modules report 40-bit width.
Changed the DIMM data bus width test to 'less than 64' instead of 'equal 32'.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Remove a few absolute references to CFG_MONITOR_BASE for ppc/mpc83xx
and use GOT relative reference.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
in the spirit of commit 1ced121600b2060ab2ff9f0fddd9421fd70a0dc6,
85xx's "Update SVR numbers to expand support", simplify SPRIDR processing
and processor ID display. Add REVID_{MAJ,MIN}OR macros to make
REVID dependent code simpler. Also added PARTID_NO_E and IS_E_PROCESSOR
convenience macros.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
delete ddr_clk and use mem_clk instead. Rename other ddr_*_clk to
mem_*_clk for consistency's sake.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
device_type = "soc" is being deprecated, newer device trees will use
"fsl,soc" and/or "fsl,immr" for the soc nodes.
This patch also adds clock-frequency property for soc nodes (the same
value as bus-frequency).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
|
This patch adds few routines to configure serdes on 837x targets.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
|
..plus get rid of some #ifdefs in the .c files.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
|
The following changes are based on kernel UCC ethernet performance:
1. Make the CSB bus pipeline depth as 4, and enable the repeat mode
2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT
switch to enable this setting.
The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:
3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting
previously.
5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on
Twr=15ns, and this was already the setting in DDR_MODE)
6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
Trp=15ns)
7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
Tras=40ns)
8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
Trcd=15ns)
9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on
Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based
on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
on CL=3 and WL=2).
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
|
R29 was an unlucky choice as with recent toolchains (gcc-4.2.x) gcc
will refuse to use load/store multiple insns; instead, it issues a
list of simple load/store instructions upon function entry and exit,
resulting in bigger code size, which in turn makes the build for a
few boards fail.
Use r2 instead.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
|
|
Move the flat device tree setup for QE related devices into
a common file shared between 83xx & 85xx platforms that have QE's.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The commit 9e89647889cd4b5ada5b5e7cad6cbe55737a08d7
will cause the mpc8315erdb board can't boot up.
The patch fix that bug, and remove the duplicated #ifdef
CFG_SPCR_TSECEP code and clean the SCCR_TSEC2 for
MPC8313E processor.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
System registers that are modified are the Arbiter Configuration
Register (ACR), the System Priority Control Register (SPCR), and the
System Clock Configuration Register (SCCR).
Signed-off by: Michael F. Reiss <Michael.F.Reiss@freescale.com>
Signed-off by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The TSEC emergency priority definition of 831x/837x
is different than the definition of 834x in SPCR register.
Add the other config of TSEC emergency priority into
cpu_init.c
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]
For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.
The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
The DDR doesn't work on the 266MHz data rate,
the patch fix the bug.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
New device trees will use "fsl,qe" compatible properties.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
convert to using simpler mpc85xx style fdt update code; streamline by
eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm
the old school FLAT_TREE code from 83xx (since the sbc8349 was just
converted over to using libfdt).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
|
|
The MPC837xEMDS board support:
* DDR2 400MHz hardcoded and SPD init
* Local bus NOR Flash
* I2C, UART, MII and RTC
* eTSEC RGMII
* PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
The MPC8315E SoC including e300c3 core and new IP blocks,
such as TDM, PCI Express and SATA controller.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
The MPC837x SoC including e300c4 core and new IP blocks,
such as SDHC, PCI Express and SATA controller.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Update libfdt to commit 8eaf5e358366017aa2e846c5038d1aa19958314e from
the device tree compiler (dtc) project.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This reverts commit 057004f4a4863554d56cc56268bfa7c7d9738e27.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
introduced in the implement board_add_ram_info patch as I was cleaning out the
magic numbers. sorry.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
add board_add_ram_info, to make memory diagnostic output more
consistent. u-boot banner output now looks like:
DRAM: 256 MB (DDR1, 64-bit, ECC on)
and for boards with SDRAM on the local bus, a line such as this is
added:
SDRAM: 64 MB (local bus)
also replaced some magic numbers with their equivalent define names.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
this adds libfdt support code for the freescale
mpc8313erdb, mpc832xemds, mpc8349emds, mpc8349itx,
and gp boards.
Boards remain compatible with OF_FLAT_TREE.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
also adds common prototypes to include/common.h.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
PCI clocks and QE frequencies weren't being updated, and the core clock
was being updated incorrectly. This patch also adds a /memory node if
it doesn't already exist prior to update.
plus some cosmetic trimming to single line comments.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
suppress the warning 'burstlen' of spd_sdram.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
Remove the duplicated source code of ecc command on the <board>.c,
for reused, move these code to cpu/mpc83xx directory.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The burst length should be 4 for DDR2 with 32 bits bus
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
add libfdt support to the generic 83xx pci code
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
..and not the global fdt. Rename local fdt vars to blob so as not to
be confused with the global var with the same three-letter name.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Several node strings were not correct (trailing slashes and properties
in the strings)
Added setting of the timebase-frequency.
Improved error messages and use debug() instead of printf().
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The new name matches more closely the kernel's name, which is also
a much better description.
These are the mpc83xx changes made necessary by the function name change.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
83xx processor family has many reset sources, such as
power on reset, software hard reset, software soft reset,
JTAG, bus monitor, software watchdog, check stop reset,
external hard reset, external software reset.
sometimes, to figure out the fault of system, we need to
know the cause of reset early before the prompt of
u-boot present.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Update the cpu_init_f() function in cpu/mpc83xx/cpu_init.c to program the
bitfields for all 83xx processors. The code to update some bitfields was
compiled only on some processors. Now, the bitfields are programmed as long
as the corresponding CFG_SCCR option is defined in the board header file.
This means that the board header file should not define any CFG_SCCR macros
for bitfields that don't exist on that processor, otherwise the SCCR will be
programmed incorrectly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This change adds 8360 silicon revision 2.1 support to u-boot.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
|
