| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This patch adds support for Flex-OneNAND devices.
Signed-off-by: Rohit Hagargundgi <h.rohit@samsung.com>
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
|
|
The commit 66372fe2 manually relocated the bbt pattern pointer,
which can be removed by using full relocation.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
|
|
The syndrome based page read/write routines store ECC, and possibly other
"OOB" data, right after each chunk of ECC'd data. With ECC chunk size of
512 bytes and a large page (2KiB) NAND, the layout is:
data-0 OOB-0 data-1 OOB-1 data-2 OOB-2 data-3 OOB-3 OOB-leftover
Where OOBx is (prepad, ECC, postpad). However, the current "raw" routines
use a traditional layout -- data OOB, disregarding the prepad and postpad
values -- so when they're used with that type of ECC hardware, those calls
mix up the data and OOB. Which means, in particular, that bad block
tables won't be found on startup, with data corruption and related chaos
ensuing.
The current syndrome-based drivers in mainline all seem to use one chunk
per page; presumably they haven't noticed such bugs.
Fix this, by adding read/write page_raw_syndrome() routines as siblings of
the existing non-raw routines; "raw" just means to bypass the ECC
computations, not change data and OOB layout.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
When computing oobavail from the list of free areas in the OOB,
don't assume there will always be an unused slot at the end.
This syncs up with the kernel NAND driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
The patch updates the check condition for determining
whether the ECC corrections has failed.
This makes it similar to what is in the kernel NAND driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Patch updates the comments and explanations for
the arguments to various functions.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
This was originally part of Thomas Gleixner's patch for
adding support for 4KiB pages.
This is not part of the U-Boot NAND driver so updating the
driver with this to sync up with the kernel NAND driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Patch removes already commented out dead code
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
This patch updates the "chip_shift" calculation in the
NAND driver. This is being done to sync up the NAND driver with
the kernel NAND driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
This patch adds support for NANDs greater than 2 GB.
Patch is based on the MTD NAND driver in the kernel.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Make smc911x_initialize return -1 on error and number of interfaces
detected otherwise.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
|
|
Sometimes, inside NetLoop, eth_halt() is called before eth_init() has
been called. This is harmless except for free() calls to pointers
which have not been allocated yet.
This patch initializes those pointers to NULL and allocates them only
the first time. This way we can get rid of free calls in halt callback.
This has been tested in i.MX27 Litekit board and eldk-4.2 toolchains.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
This patch fixes erroneous access to the ethernet PHY which broke the driver.
1. Selector field in the auto-negotiation register must be 0x00001 for
using 802.3, not 0x00000 which is reseved.
2. Access to the PHY address specified by CONFIG_FEC_MXC_PHYADDR, not
0x0 fixed address.
This has been tested in i.MX27 Litekit board and eldk-4.2 toolchains.
Now using proper defines for auto-negotiation register.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
This patch fixes the following warnings:
Configuring for xaeniax board...
smc91111_eeprom.c: In function 'print_macaddr':
smc91111_eeprom.c:278: warning: suggest parentheses around + or - in operand of &
smc91111_eeprom.c:281: warning: suggest parentheses around + or - in operand of &
...
Configuring for xsengine board...
smc91111_eeprom.c: In function 'print_macaddr':
smc91111_eeprom.c:278: warning: suggest parentheses around + or - inside shift
smc91111_eeprom.c:281: warning: suggest parentheses around + or - inside shift
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
The following error was seen on impa7 board, due to its use of a 32-bit bus
on CS8900.
cs8900.c:137:37: error: macro "get_reg_init_bus" passed 2 arguments, but takes just 1
This patch gives the macro the correct number of arguments
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Ensure all CS8900 data structures are assigned before accessing device
Signed-off-by: Hui.Tang <zetalabs@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
commit 70ed869e broke fsl pcie end-point initialization.
Returning 0 is not correct. The function must return the first free
bus number for the next controller.
fsl_pci_init() must still be called and a bus allocated even if the
controller is an end-point.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This reverts commit 70ed869ea5f6b1d13d7b140c83ec0dcd8a127ddc.
There isn't any need to modify the API for fsl_pci_init_port to pass the
status of host/agent(end-point) status. We can determine that
internally to fsl_pci_init_port. Revert the patch that makes the API
change.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
|
In 16 bpp mode, the new IPEK01 board only requires swapping of D16 words
for D32 accesses due to the diffferent connecting to the GDC bus. This
patch introduces the configuration option VIDEO_FB_16BPP_WORD_SWAP,
which should be set for all board using the mb862xx in 16 bpp mode. For
the IPEK01, VIDEO_FB_16BPP_PIXEL_SWAP should not be set.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
|
|
The new IPEK01 board can use the 32 bpp mode for the Lime graphics
controller. For this mode, video accelaration does not work. This patch
makes the accelaration configurable via CONFIG_VIDEO_MB862xx_ACCEL,
which is enabled for the lwmon5 and the socrates board for backward
compatibility.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
|
|
To avoid board-specific code accessing the mb862xx registers directly,
the public function mb862xx_probe() has been introduced. Furthermore,
the "Change of Clock Frequency" and "Set Memory I/F Mode" registers
are now defined by CONFIG_SYS_MB862xx_CCF and CONFIG_SYS_MB862xx__MMR,
respectively. The BSPs for the socrates and lwmon5 boards have been
adapted accordingly.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
|
|
Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
While we're here, improve the speed calculation a bit to match the HRM.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The current transfer code relies on ctrlc() to abort transfers, but this
requires user interactivity. Naturalize the process with a timeout.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Proper behavior is to pull MAC address from NVRAM in the initialization() an
stuff it in dev->address, then program the device from dev->address in
the init() function.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Currently the CFI driver issues both AMD and Intel reset commands.
This is because the driver doesn't know yet which chips are connected.
This dual reset seems to cause problems with the M29W128G chips as
reported by Richard Retanubun. This patch now introduces a weak default
function for the CFI reset command, still with both resets. This can
be overridden by a board specific version if necessary.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Richard Retanubun <RichardRetanubun@ruggedcom.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Add missing newline.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Luigi Mantellini <luigi.mantellini@idf-hit.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
|
|
Setup QE pin multiplexing for USB function, configure needed BCSRs
and add some fdt fixups.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Originally written by Jason Jin and Mingkai Hu for mpc8536.
When QorIQ based board is configured as a PCIe agent, then unlock/enable
inbound PCI configuration cycles and init a 4K inbound memory window;
so that a PCIe host can access the PCIe agents SDRAM at address 0x0
* Supported in fsl_pci_init_port() after adding pcie_ep as a param
* Revamped copyright in drivers/pci/fsl_pci_init.c
* Mods in 85xx based board specific pci init after this change
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Some of the new spi flash files were missing explicit license lines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
|
|
Move the test up in the function to not hang on systems without ethernet.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
|
|
fix the following compile warnings
warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
This patch re-formats the arm920t s3c24x0 nand driver in preparation for changes
to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4, 2/4 and 3/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch re-formats the arm920t s3c24x0 driver files, excluding the nand
driver, in preparation for changes to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4 and 2/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch includes the serial driver for s5pc1xx.
s5pc1xx uart driver needs own register setting and clock configuration.
So, need to special driver.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch includes the onenand driver for s5pc100
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
Refactor the smc911x driver to allow for detecting when the chip is missing.
I.e. the detect_chip() function is called earlier and will abort gracefully
when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Fix warning
Dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: Steve Sakoman <sakoman@gmail.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
|
|
|
|
Forcing the tables into got2 caused extra relocation when using -mrelocatable.
This patch requires any board defining CONFIG_BIOSEMU to use -mrelocatable.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Jin Zhengxiong <Jason.Jin@freescale.com>
|
|
arbitrary number of mii buses.
This feature is useful when your board uses different mii buses for different
phys and all (or a part) of these buses are implemented via bit-banging mode.
The driver requires that the following macros should be defined into the board
configuration file:
CONFIG_BITBANGMII - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support
If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
to define at least the following macros:
MII_INIT - Generic code to enable the MII bus (optional)
MDIO_DECLARE - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ - Read the MDIO pin
MDIO(v) - Write v on the MDIO pin
MDC_DECLARE - Declaration needed to access to the MDC pin (optional)
MDC(v) - Write v on the MDC pin
The previous macros make the driver compatible with the previous version
(that didn't support the multi-bus).
When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill
the bb_miiphy_buses[] array with a record for each required bus and declare
the bb_miiphy_buses_num variable with the number of mii buses.
The record (struct bb_miiphy_bus) has the following fields/callbacks (see
miiphy.h for details):
char name[] - The symbolic name that must be equal to the MII bus
registered name
int (*init)() - Initialization function called at startup time (just
before the Ethernet initialization)
int (*mdio_active)() - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)() - Write the MDIO pin
int (*get_mdio)() - Read the MDIO pin
int (*set_mdc)() - Write the MDC pin
int (*delay)() - Delay function
void *priv - Private data used by board specific code
The board code will look like:
struct bb_miiphy_bus bb_miiphy_buses[] = {
{ .name = miibus#1, .init = b1_init, .mdio_active = b1_mdio_active, ... },
{ .name = miibus#2, .init = b2_init, .mdio_active = b2_mdio_active, ... },
...
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
sizeof(bb_miiphy_buses[0]);
Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
|
|
Modify all existing *.c files to use the new register names
as seen in the AMCC manuals.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
if link up detection code is disabled through config option, it gives build warning.
This patch fixes the same
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
