Age | Commit message (Collapse) | Author |
|
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
- Initial pin configuration.
- Introduction of u8500_is_snowball.
- Introduction of new machine type.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
ST-Ericsson ID: 321908
Change-Id: Ib51c36558e37c7f52db638052644758e6d3cc51a
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/13848
Reviewed-by: QATOOLS
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
Verification of the kernel and ITP signature before allowing to boot is
added. This feature is configurable and by default not activated. MeeGo-
built RPM will have this enabled.
ST-Ericsson ID: WP275634, ER275440
Change-Id: Ib888f39dd5dca1bc8b7d6e1b002da83a77908b07
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/11415
Tested-by: Robert ROSENGREN <robert.rosengren@stericsson.com>
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Jens WIKLANDER <jens.wiklander@stericsson.com>
|
|
The HREFP 2.0 V60 has no GPIO expander, therefore some GPIO lines
were moved around.
The preferred approach was to first check if there is a machid in the
environment. And if not try to program the GPIOE. If that fails, assume
it is a V60 or newer.
But for the splash screen, we need to know very early on which HW
version we are running. At that time no environment is available,
therefore it is unavoidable to do the I2C access (10 ms timeout), if
both HW versions shall be supported in one binary.
CAUTION: you need also a Linux kernel which supports MACH_TYPE_HREFV60.
Older U8500 kernels will not even issue a start-up message.
Depends-On: http://gerrit.lud.stericsson.com/gerrit/12335
ST-Ericsson ID: CR 272893
Change-Id: Id794df8c185dfbf67f7bce81deb49abf71129f7b
Signed-off-by: Michael Brandt <michael.brandt@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/12578
Reviewed-by: Torbjorn SVENSSON <torbjorn.x.svensson@stericsson.com>
Reviewed-by: Robert ROSENGREN <robert.rosengren@stericsson.com>
Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com>
Reviewed-by: Bibek BASU <bibek.basu@stericsson.com>
|
|
Splitting security related code from itp.c into sec_bridge.c
ST-Ericsson ID: WP275634
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: I813daf0d0eaea4645e7d990bf467f19b0af968db
Signed-off-by: Robert Rosengren <robert.rosengren@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/10895
Reviewed-by: QATOOLS
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
itp.c and cspsa_fp.c is SoC specific, not board specific.
Other db8500 based boards need it as well, therefore move it into
the SoC directory.
ST-Ericsson ID: WP275634
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: I386c0d84e9f44f18ded0d9059fc2dae4c27974f2
Signed-off-by: Robert Rosengren <robert.rosengren@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/10894
Reviewed-by: QATOOLS
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Reviewed-by: Joakim AXELSSON <joakim.axelsson@stericsson.com>
|
|
Copied the GPIO configurator written for the Linux kernel.
The Nomadik db8500 GPIO driver. Purpose is to be able
to just cut-n-paste the GPIO config from Linux to U-boot.
Also at the same time remove the obsolete and old
gpio_alt_funcenable/disable methods.
Now all is configured using a table in u8500.c.
Now drivers doesn't have to worry about setting up the GPIO pins.
Actually no driver today uses GPIO pins directly, only via
hardware blocks within db8500. Functions are still added
to be able to interact directly with a GPIO pin. This also
cleaned up a lot of driver by not having to bit manipulate GPIO
registers them self.
The new driver is called db8500_gpio and placed in driver/gpio/.
Functions are in include/db8500_gpio.h:
void db8500_gpio_set_pull(unsigned gpio, enum db8500_gpio_pull pull);
void db8500_gpio_make_input(unsigned gpio);
int db8500_gpio_get_input(unsigned gpio);
void db8500_gpio_make_output(unsigned gpio, int val);
void db8500_gpio_set_output(unsigned gpio, int val);
And for the configurator in include/db8500_pincfg.h:
void db8500_gpio_config_pins(pin_cfg_t *cfgs, size_t num);
All in all the final binary size has decreased.
This is only done for db8500 nomadik GPIO. The code for gpio
expanders has not been touched.
All references to Nomadik has been removed in this driver.
Only db8500 is left.
ST-Ericsson ID: None
Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com>
Change-Id: I90aa1d46c813ffb5a777c3492b5751f5054f71cf
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9904
Reviewed-by: QATOOLS
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
Clean up of PRCMU code in db8500 SoC code. Move things from cpu.c
and clock.h to prcmu.c. Also remove duplicate #defines and have
prcmu.c use the #defines in prcmu.h.
ST-Ericsson ID: None
Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com>
Change-Id: Ieffb0094b3f43f0c88f3ed457c6cb296fa0ce378
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9899
Reviewed-by: QATOOLS
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
Enable CONFIG_DISPLAY_CPUINFO and implement print_cpuinfo() in
cpu/arm_cortexa9/db8500.c.
ST-Ericsson ID: None
Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com>
Change-Id: Id4f67b223fabc4a8007229f8db12bd2a7362f8c2
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7115
Reviewed-by: QATOOLS
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
Moved clock code from board/st/u8500/u8500.c to
cpu/arm_cortexa9/db8500/clock.c.
Remove code to simulate Maja clocks.
ST-Ericsson ID: None
Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com>
Change-Id: Ibbb21d53091ceaddcc01e1a195e129039f986696
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7114
Reviewed-by: QATOOLS
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
Moved u8500_is_earlydrop() and cpu_is_u8500*() to
include/asm-arm/arch-db8500/cpu.h.
They are kept in cpu.h as the functions are very small and
should be inlined with each use of them.
The final binary actually also became around 100 bytes smaller.
ST-Ericsson ID: None
Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com>
Change-Id: Ied553b7c8a004a37c70c3e328a069ae8b2a92b23
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9893
Reviewed-by: QATOOLS
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
First patch to split cpu_arch SoC-code away from board code.
Added usage of arch_cpu_init() which is the corresponding
to board_init().
Moved db8500 code from board/st/u8500/u8500.c to
cpu/arm_cortexa9/db8500/cpu.c.
Also created include/asm/arch-db8500/cpu.h and
include/asm/arch-db8500/prcmu.h.
ST-Ericsson ID: None
Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com>
Change-Id: I403d7d4f6c655c0d383afb3cb3be7e7df96683a3
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7150
Reviewed-by: Joakim AXELSSON <joakim.axelsson@stericsson.com>
Tested-by: Joakim AXELSSON <joakim.axelsson@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
Started work with splitting the files in board/st/u8500 into
proper SoC (system on a chip), drivers, commands and board code.
ST-Ericsson ID: None
Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com>
Change-Id: I33300b1990f377bc049785102f1c87fbe579e86d
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7089
Reviewed-by: Robert ROSENGREN <robert.rosengren@stericsson.com>
Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com>
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
Reviewed-by: Mikael LARSSON1 <mikael.xt.larsson@stericsson.com>
|
|
common.h and gpio.h were present in the u8500 board directory and in the
SoC include directory include/asm-arch/arch-stw8500.
This patch removes the duplicates in the board directory and replaces
all "common.h" and "gpio.h" with <asm/arch/common.h> and
<asm/arch/gpio.h>, respectively.
Change-Id: I4ff2a3a11324200222e3ae5b9d22eee6427f6d4c
Signed-off-by: Michael Brandt <michael.brandt@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/8838
Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com>
Reviewed-by: Rikard OLSSON <rikard.p.olsson@stericsson.com>
|
|
To get numbers for 5500 machines and official SVP8500 numbers.
ST-Ericsson ID: ER280045
mach-types are equivalent to the following patch:
ST-Ericsson ID: AP279856
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Change-Id: I0ce5ce2c31cc3e35fadd01acc20f077992be2f0d
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/8775
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
This patch removes splash image from u-boot binary and loads it from a toc entry
called SPLASH instead.
Depends-On: I2e182df7fa056a5df2deb05a4ebab844eedbb85d
I715045aba01c1c747f9bd15f02c6d057f66ff968
I93e63a092fd6f229f530e55ec4b98e8e09db1c06
ST-Ericsson ID: ER268766
Change-Id: I4ee7885618d18d526dfca55d7c45b769cd9b52c9
Signed-off-by: Mikael Larsson <mikael.xt.larsson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/6879
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Reviewed-by: Rikard OLSSON <rikard.p.olsson@stericsson.com>
|
|
Added SPI support for U8500
ST-Ericsson ID: 269867
ST-Ericsson FOSS-OUT ID: STETL-FOSS-OUT-10121
Change-Id: Ied17dd39aa1ebc0ee95818c59c7f211ce655b8bf
Signed-off-by: Markus Helgesson <markus.helgesson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7569
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
Handle the changed TCDM base address on DB8500v2, and the required chip
bits to the I2C slave address. Based on the Linux modifications.
Change-Id: I9fc8df1553824bd03a908a5c4285be284ea158db
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/4213
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
- Add cpu_is_u8500v2() for identification: ASICID has moved, so use
the MIDR for primary identification.
- Handle the changed MTU0 enable bit
- Handle the MMC DBLOCKSIZE field move
ST-Ericsson ID: CR267426
Change-Id: Ieae6032cf4e96796a8b53cfb95b28b26d4cf9a7b
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/3960
Reviewed-by: Martin LUNDHOLM <martin.xa.lundholm@stericsson.com>
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
IR265772: MMC driver does not detect SDHC cards.
IR254201: Restructure MMC/SD driver for U8500 board according to the
block device framework in mainline U-Boot.
Changes to mmc framework:
- Multi Block Read support in mmc framework.
- Wrap Multi Block Write/Read to be able to adopt for large transaction.
- Removed incorrect check in EXT CSD for high capacity MMC.
- Corrected check for high capacity SD cards.
- Set MMC buswidth to 8, prio of using 4.
Known limitations/bugs in mmc framework:
- High capacity MMC, will likely not get the correct density.
- High speed is set, whether or not the host supports it or not.
board/st/u8500/mmc_utils:
IMPORTANT FOR DEVELOPERS:
- Removed unessary U-Boot commands which is already supported in
cmd_fat.
- mmc_read_cmd_file: Read command.txt into bootcmd env from FAT FS in
SD card.
- write_partition_block: Writes the MBR if it is not already written.
board/st/u8500/mmc_host[c.h]:
- Implements the entire MMC/SD host driver for the PL180 block.
- There is still room for optimization:
Increase CLK-speed.
Use high-speed for SD cards.
Is GPIO setup correctly for both cards an eMMC.
EarlyDrop support not fully tested.
Dynamically turn on voltage/clocks to SD, not always.
More...
Note:
- Increased read/write performance for eMMC, to around 5.4 MB/s for
sequential read/write. Earlier measurements was 3.5 MB/s for read and
2.6 MB/s for write.
ST-Ericsson ID: ER265772, CR267996, ER267993
Change-Id: I921102edbde761407ff5ad476d1bb99f5dc7a2ef
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/2288
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
Reviewed-by: Martin LUNDHOLM <martin.xa.lundholm@stericsson.com>
Tested-by: Martin LUNDHOLM <martin.xa.lundholm@stericsson.com>
Reviewed-by: Mikael LARSSON <mikael.xt.larsson@stericsson.com>
Tested-by: Mikael LARSSON <mikael.xt.larsson@stericsson.com>
|
|
Boottime now internally uses us instead of ticks.
Reviewed-by: Michael Brandt <michael.brandt@stericsson.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Change-Id: If30d2eb384d6e82daa86c3cab7a6fd2a22baefb5
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/3053
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
This implements vibrator feature using AB8500 chip and I2C i/f.
The vibrator driver provides shell command "vibrate".
Checked with HREFP boards: 1.1_V21, 1.1_V31, 1.1_V33
ST-Ericsson ID: AP266348
Change-Id: Ifd0d780b41c4285038b8de659cdeac2086b8e873
Signed-off-by: Grzegorz Sygieda <grzegorz.sygieda@tieto.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/2937
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
This patch does the following:
* Startup graphics only support for HREF+.
* Displays a logo last in the u-boot sequence before the kernel is booted.
* Informs the kernel not to display penguins.
* Added pmem values to bootargs.
ST Ericsson Change-ID: WP236570
Change-Id: Ib176c17a795ddd002e94344eb9c67739b1e2269e
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/1048
Reviewed-by: Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Change-Id: Ieec8e7940e7acdc88d7c17b12007f61841741325
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/390
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
On HREF+, SD card power supply is controlled by the Vaux3 regulator. In
order to enable the power supply, port the AB8500 PRCMU I2C read/write
code from Linux to U-Boot, and then write the appropriate registers via
those functions.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Change-Id: I470f3da694e6ea0e3e0e16571c3048066f0a4309
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/388
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
This patch is part of WP254081 which depends on WP252006.
* Fixed I2C, use real timeouts instead of counter
* Undefined CONFIG_BOOTTIME, since it as to be changed to new timer.c
* Merged V1 patches from Bangalore
The patches were merged manually, because of the differences
of the U-Boot baseline (Bangalore U-Boot 1.3.1, Lund 2009.11).
The original patches were created by Rabin Vincent
<rabin.vincent@stericsson.com>.
and were applied originally to
Branches: blr_lsp, remotes/origin/blr_lsp
Follows: qpppaaa_20100210_094651
0001-u8500-gpio-add-I2C0-altfun.patch
0002-u8500-use-correct-v1-macros.patch
0003-emmc-clean-up-paritioning.patch
0004-u8500-remove-incorrect-ram-settings.patch
0005-u8500-gpio-remove-unnecessary-ifdefs.patch
0006-u8500-add-ED-v1-detection-and-handle-eMMC-diff.patch
0008-u8500-mmc-don-t-disable-altfuns.patch
0009-u8500-gpio-remove-unused-defined.patch
0010-u8500-mmc-add-barrier-for-while-loop.patch
0011-u8500-mmc-handle-non-block-addressed-cards.patch
0012-u8500-mmc-remove-unused-gpio-settings-on-v1.patch
0013-u8500-emmc-build-fix.patch
0014-u8500-handle-v1-gpios-and-clocks.patch
0015-mmc-build-fix-for-block-addressing.patch
0016-u8500-add-clocks-and-hardware-files.patch
0017-u8500-enable-PRCUM-timers-reg-for-ED.patch
0018-u8500-handle-MTU-for-v1-ED.patch
0019-u8500-emmc-remove-unnecessary-GPIO-settings.patch
0020-u8500-remove-dead-code.patch
0021-u8500-add-working-MTU-timer.patch
0022-pl011-empty-rx-fifo-if-necessary.patch
0023-u8500-gpio-fix-cont-handling-in-altfunc.patch
0024-u8500-reduce-bootdelay-to-1-and-enable-zero-check.patch
0025-u8500-disable-forcing-of-verify-but-set-n-by-default.patch
0029-u8500-fix-some-gpio-settings.patch
0030-emmc-make-v1-paritioning-differences-explicit.patch
Signed-off-by: Michael Brandt <Michael.Brandt@stericsson.com>
Change-Id: I1106702e393c34f630e71f071e06c3952b0d3a1a
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/182
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
|
|
measurement. Note: idle time measurement does not seem to work reliable at the moment. Verification needed.
Signed-off-by: Michael Brandt <Michael.Brandt@stericsson.com>
|
|
|
|
Added DA8xx GPIO base addresses in gpio_defs.h and pointers
to different BANKs which can be used to program GPIOs.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
|
|
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php
And built with
repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
commit c9f937e4a3f4ebf9924ec21d80632e5eb61d949c
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
Davinci: NAND enable ECC even when not in NAND boot mode
On Davinci platforms, the default NAND device is enabled (for ECC)
in low level boot code when NAND boot mode is used. If booting in
another mode, NAND ECC is not enabled. The driver should make
sure ECC is enabled regardless of boot mode if NAND is configured
in U-Boot.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
|
|
Davinci: Configurable NAND chip selects
Add a CONFIG_SYS_NAND_CS setting to all davinci configs and
use it to setup the NAND controller in the davinci_nand
mtd driver.
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
|
|
Conflicts:
.gitignore
include/configs/u8500.h
|
|
Conflicts:
include/usb/musb_udc.h
|
|
by the linux kernel and we still want to be able to use that timer for boottime measurement. IE leave the 3rd timer run until we're executing init. Added atags for u-boot timing measurements as communication with the kernel.
|
|
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php
And built with
repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
commit 3fcca9ac6cbce35b3e81e247d375534117d5f4cd
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
This patch adds support for A320 evaluation board from Faraday. This board
uses FA526 processor by default and has 512kB and 32MB NOR flash, 64M RAM.
FA526 is an ARMv4 processor and uses the ARM920T source in this patch.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
|
|
Defaults are for Infineon DDR timings.
Since none of the supported boards currently do
XIP boot, these seem to be faulty. fix the values
as per the calculations(ACTIMA,B), conf
the sdrc power with pwdnen and wakeupproc bits
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Micron DDR timings based on:
http://www.sakoman.net/cgi-bin/gitweb.cgi?p=x-load-omap3.git;a=blob;f=include/asm/arch-omap3/mem.h;h=e6fbfe3947f5d0d85fea776e30821d4017316d86;hb=HEAD
Introduce Micron DDR timings and provide
CONFIG_OMAP3_INFINEON_DDR and CONFIG_OMAP3_MICRON_DDR config
options to allow for platform files to setup their timings as
per the type of DDR selected
Reported-by: Steve Sakoman in http://www.nabble.com/forum/Permalink.jtp?root=25779518&post=25959734&page=y
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Remove SDP referenced unused defines
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Provides initial support for TI OMAP-L1x/DA8xx SoC devices.
See http://www.ti.com
The DA8xx devices are similar to DaVinci devices but have a differing
memory map and updated peripheral versions.
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Cleans up the s3c24x0 header files:
s4c24x0.h: removes the use of 'volatile' from the S3C24X0_REG8,
S3C24X0_REG16 and S3C24X0_REG32 register typedef's. Registers are always
accessed using the IO accessor functions which cast the register address
as 'volatile' anyway so it isn't required here.
s3c2400.h and s3c2410.h: insert a blank line between the static inline
functions
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
|
|
This patch moves the s3c64xx header files from include/
to include/asm-arm/arch-s3c64xx
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch moves the s3c24x0 header files from include/ to
include/asm-arm/arch-s3c24x0/.
checkpatch.pl showed 2 errors and 3 warnings. The 2 errors were both due
to a non-UTF8 character in David M?ller's name:
ERROR: Invalid UTF-8, patch and commit message should be encoded in UTF-8
#489: FILE: include/asm-arm/arch-s3c24x0/s3c2410.h:3:
+ * David M?ller ELSOFT AG Switzerland. d.mueller@elsoft.ch
As David's name correctly contains a non-UTF8 character I haven't fixed
these errors.
The 3 warnings were all because of the use of 'volatile' in s3c24x0.h:
WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt
#673: FILE: include/asm-arm/arch-s3c24x0/s3c24x0.h:35:
+typedef volatile u8 S3C24X0_REG8;
+typedef volatile u16 S3C24X0_REG16;
+typedef volatile u32 S3C24X0_REG32;
I'll fix these errors in another patch.
Tested by running MAKEALL for ARM8 targets and ensuring there were no new
errors or warnings.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php
And built with
repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
commit 156171c71a0dc4bce12b4408bb1591f8fe32dc1a
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
From http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
Commit id 0996391139f43d032335b5360db11da62a2cbb39
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|