| Age | Commit message (Collapse) | Author |
|---|
|
The ECC POST reported intermittent failures running after power-up on
the Korat PPC440EPx board. Even when the test passed, the debugging
output occasionally reported additional unexpected ECC errors.
This refactoring has three main objectives: (1) minimize the code
executed with ECC enabled during the tests, (2) add more checking of the
results so any unexpected ECC errors would cause the test to fail, and
(3) use synchronization (only) where required by the processor.
Signed-off-by: Larry Johnson <lrj@acm.org>
|
|
post/cpu/ppc4xx/spr.c contained a few checks for registers only present
for PPC440 and derivates processor.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Signed-off-by: Larry Johnson <lrj@acm.org>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
As repoted by Larry Johnson, running "diag run cache" caused a crash
in U-Boot. This problem was introduced by a patch that removed the
TLB entry for the cache test after the test has completed. Since this
TLB was only setup once, a 2nd attempt to run this cache test
failed with a crash. Now this TLB entry is created every time the
routine is called.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch allows the ECC POST to be used for different boards with the
PPC440 Denali SDRAM controller. Modifications include skipping the test
if ECC is not enabled (as for non-ECC DIMMs) and adding synchronization
to prevent timing errors.
Signed-off-by: Larry Johnson <lrj@acm.org>
|
|
Signed-off-by: Larry Johnson <lrj@acm.org>
|
|
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
|
|
This patch enables the 4xx EMAC POST driver to work too, when dcache is
enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The POST ethernet test needed to be changed to dynamically determine
the count of ethernet devices. This code is cloned from the 4xx
ethernet driver.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
When CFG_POST_ETHER_EXT_LOOPBACK is defined, the ethernet POST
is not done using an internal loopback connection, but by assuming
that an external loopback connector is plugged into the board.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The patch adds support for UART POST on ppc44x-based boards with no
external serial clocks installed.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
- Clear ECC status regs after ECC POST test
- Set dcbz for ECC generation with caches enabled as default
- Code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
|
|
Added memory, CPU, UART, I2C and SPR POST tests for PPC440.
Signed-off-by: Igor Lisitsin <igor@emcraft.com>
--
|
