/* * Copyright (c) 2005 * Travis B. Sawyer, Sandburst Corporation, tsawyer@sandburst.com * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #include #include #include #include "metrobox.h" #include "metrobox_version.h" #include #include #include #include #include "../common/ppc440gx_i2c.h" #include "../common/sb_common.h" void fpga_init (void); METROBOX_BOARD_ID_ST board_id_as[] = { {"Undefined"}, /* Not specified */ {"2x10Gb"}, /* 2 ports, 10 GbE */ {"20x1Gb"}, /* 20 ports, 1 GbE */ {"Reserved"}, /* Reserved for future use */ }; /************************************************************************* * board_early_init_f * * Setup chip selects, initialize the Opto-FPGA, initialize * interrupt polarity and triggers. ************************************************************************/ int board_early_init_f (void) { ppc440_gpio_regs_t *gpio_regs; /* Enable GPIO interrupts */ mtsdr(sdr_pfc0, 0x00103E00); /* Setup access for LEDs, and system topology info */ gpio_regs = (ppc440_gpio_regs_t *)CFG_GPIO_BASE; gpio_regs->open_drain = SBCOMMON_GPIO_SYS_LEDS; gpio_regs->tri_state = SBCOMMON_GPIO_DBGLEDS; /* Turn on all the leds for now */ gpio_regs->out = SBCOMMON_GPIO_LEDS; /*--------------------------------------------------------------------+ | Initialize EBC CONFIG +-------------------------------------------------------------------*/ mtebc(xbcfg, EBC_CFG_LE_UNLOCK | EBC_CFG_PTD_ENABLE | EBC_CFG_RTC_64PERCLK | EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS | EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_DEFAULT | EBC_CFG_PME_DISABLE | EBC_CFG_PR_32); /*--------------------------------------------------------------------+ | 1/2 MB FLASH. Initialize bank 0 with default values. +-------------------------------------------------------------------*/ mtebc(pb0ap, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) | EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) | EBC_BXAP_WBF_ENCODE(1)| EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY | EBC_BXAP_PEN_DISABLED); mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) | EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT); /*--------------------------------------------------------------------+ | 8KB NVRAM/RTC. Initialize bank 1 with default values. +-------------------------------------------------------------------*/ mtebc(pb1ap, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(10) | EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) | EBC_BXAP_WBF_ENCODE(1)| EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY | EBC_BXAP_PEN_DISABLED); mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x48000000) | EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT); /*--------------------------------------------------------------------+ | Compact Flash, uses 2 Chip Selects (2 & 6) +-------------------------------------------------------------------*/ mtebc(pb2ap, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) | EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0)| EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY | EBC_BXAP_PEN_DISABLED); mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(0xF0000000) | EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT); /*--------------------------------------------------------------------+ | OPTO & OFEM FPGA. Initialize bank 3 with default values. +-------------------------------------------------------------------*/ mtebc(pb3ap, EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED | EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) | EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) | EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED | EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW); mtebc(pb3cr, EBC_BXCR_BAS_ENCODE(0x48200000) | EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT); /*--------------------------------------------------------------------+ | MAC A for metrobox | MAC A & B for Kamino. OFEM FPGA decodes the addresses | Initialize bank 4 with default values. +-------------------------------------------------------------------*/ mtebc(pb4ap, EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED | EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) | EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) | EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED | EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW); mtebc(pb4cr, EBC_BXCR_BAS_ENCODE(0x48600000) | EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT); /*--------------------------------------------------------------------+ | Metrobox MAC B Initialize bank 5 with default values. | KA REF FPGA Initialize bank 5 with default values. +-------------------------------------------------------------------*/ mtebc(pb5ap, EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED | EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) | EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) | EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED | EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW); mtebc(pb5cr, EBC_BXCR_BAS_ENCODE(0x48700000) | EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT); /*--------------------------------------------------------------------+ | Compact Flash, uses 2 Chip Selects (2 & 6) +-------------------------------------------------------------------*/ mtebc(pb6ap, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) | EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0)| EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY | EBC_BXAP_PEN_DISABLED); mtebc(pb6cr, EBC_BXCR_BAS_ENCODE(0xF0100000) | EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT); /*--------------------------------------------------------------------+ | BME-32. Initialize bank 7 with default values. +-------------------------------------------------------------------*/ mtebc(pb7ap, EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED | EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) | EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) | EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED | EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW); mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48500000) | EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT); /*--------------------------------------------------------------------+ * Setup the interrupt controller polarities, triggers, etc. +-------------------------------------------------------------------*/ mtdcr (uic0sr, 0xffffffff); /* clear all */ mtdcr (uic0er, 0x00000000); /* disable all */ mtdcr (uic0cr, 0x00000000); /* all non- critical */ mtdcr (uic0pr, 0xfffffe03); /* polarity */ mtdcr (uic0tr, 0x01c00000); /* trigger edge vs level */ mtdcr (uic0vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic0sr, 0xffffffff); /* clear all */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic1er, 0x00000000); /* disable all */ mtdcr (uic1cr, 0x00000000); /* all non-critical */ mtdcr (uic1pr, 0xffffc8ff); /* polarity */ mtdcr (uic1tr, 0x00ff0000); /* trigger edge vs level */ mtdcr (uic1vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic2sr, 0xffffffff); /* clear all */ mtdcr (uic2er, 0x00000000); /* disable all */ mtdcr (uic2cr, 0x00000000); /* all non-critical */ mtdcr (uic2pr, 0xffff83ff); /* polarity */ mtdcr (uic2tr, 0x00ff8c0f); /* trigger edge vs level */ mtdcr (uic2vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic2sr, 0xffffffff); /* clear all */ mtdcr (uicb0sr, 0xfc000000); /* clear all */ mtdcr (uicb0er, 0x00000000); /* disable all */ mtdcr (uicb0cr, 0x00000000); /* all non-critical */ mtdcr (uicb0pr, 0xfc000000); mtdcr (uicb0tr, 0x00000000); mtdcr (uicb0vr, 0x00000001); fpga_init(); return 0; } /************************************************************************* * checkboard * * Dump pertinent info to the console ************************************************************************/ int checkboard (void) { sys_info_t sysinfo; unsigned char brd_rev, brd_id; unsigned short sernum; unsigned char opto_rev, opto_id; OPTO_FPGA_REGS_ST *opto_ps; opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE; opto_rev = (unsigned char)((opto_ps->revision_ul & SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_MASK) >> SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_SHIFT); opto_id = (unsigned char)((opto_ps->revision_ul & SAND_HAL_XC_XCVR_CNTL_REVISION_IDENTIFICATION_MASK) >> SAND_HAL_XC_XCVR_CNTL_REVISION_IDENTIFICATION_SHIFT); brd_rev = (unsigned char)((opto_ps->boardinfo_ul & SAND_HAL_XC_XCVR_CNTL_BRD_INFO_BRD_REV_MASK) >> SAND_HAL_XC_XCVR_CNTL_BRD_INFO_BRD_REV_SHIFT); brd_id = (unsigned char)((opto_ps->boardinfo_ul & SAND_HAL_XC_XCVR_CNTL_BRD_INFO_BRD_ID_MASK) >> SAND_HAL_XC_XCVR_CNTL_BRD_INFO_BRD_ID_SHIFT); get_sys_info (&sysinfo); sernum = sbcommon_get_serial_number(); printf ("Board: Sandburst Corporation MetroBox Serial Number: %d\n", sernum); printf ("%s\n", METROBOX_U_BOOT_REL_STR); printf ("Built %s %s by %s\n", __DATE__, __TIME__, BUILDUSER); if (sbcommon_get_master()) { printf("Slot 0 - Master\nSlave board"); if (sbcommon_secondary_present()) printf(" present\n"); else printf(" not detected\n"); } else { printf("Slot 1 - Slave\n\n"); } printf ("OptoFPGA ID:\t0x%02X\tRev: 0x%02X\n", opto_id, opto_rev); printf ("Board Rev:\t0x%02X\tID: %s\n", brd_rev, board_id_as[brd_id]); printf ("\tVCO: %lu MHz\n", sysinfo.freqVCOMhz / 1000000); printf ("\tCPU: %lu MHz\n", sysinfo.freqProcessor / 1000000); printf ("\tPLB: %lu MHz\n", sysinfo.freqPLB / 1000000); printf ("\tOPB: %lu MHz\n", sysinfo.freqOPB / 1000000); printf ("\tEPB: %lu MHz\n", sysinfo.freqEPB / 1000000); /* Fix the ack in the bme 32 */ udelay(5000); out32(CFG_BME32_BASE + 0x0000000C, 0x00000001); asm("eieio"); return (0); } /************************************************************************* * misc_init_f * * Initialize I2C bus one to gain access to the fans ************************************************************************/ int misc_init_f (void) { /* Turn on i2c bus 1 */ puts ("I2C1: "); i2c1_init (CFG_I2C_SPEED, CFG_I2C_SLAVE); puts ("ready\n"); /* Turn on fans */ sbcommon_fans(); return (0); } /************************************************************************* * misc_init_r * * Do nothing. ************************************************************************/ int misc_init_r (void) { unsigned short sernum; char envstr[255]; unsigned char opto_rev; OPTO_FPGA_REGS_ST *opto_ps; opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE; if(NULL != getenv("secondserial")) { puts("secondserial is set, switching to second serial port\n"); setenv("stderr", "serial1"); setenv("stdout", "serial1"); setenv("stdin", "serial1"); } setenv("ubrelver", METROBOX_U_BOOT_REL_STR); memset(envstr, 0, 255); sprintf (envstr, "Built %s %s by %s", __DATE__, __TIME__, BUILDUSER); setenv("bldstr", envstr); saveenv(); if( getenv("autorecover")) { setenv("autorecover", NULL); saveenv(); sernum = sbcommon_get_serial_number(); printf("\nSetting up environment for automatic filesystem recovery\n"); /* * Setup default bootargs */ memset(envstr, 0, 255); sprintf(envstr, "console=ttyS0,9600 root=/dev/ram0 " "rw ip=10.100.60.%d:::255.255.0.0:metrobox%d:eth0:none idebus=33", sernum, sernum); setenv("bootargs", envstr); /* * Setup Default boot command */ setenv("bootcmd", "fatload ide 0 8000000 pimage.metrobox;" "fatload ide 0 8100000 pramdisk;" "bootm 8000000 8100000"); printf("Done. Please type allow the system to continue to boot\n"); } if( getenv("fakeled")) { setenv("bootdelay", "-1"); saveenv(); printf("fakeled is set. use 'setenv fakeled ; setenv bootdelay 5 ; saveenv' to recover\n"); opto_rev = (unsigned char)((opto_ps->revision_ul & SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_MASK) >> SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_SHIFT); if(0x12 <= opto_rev) { opto_ps->control_ul &= ~ SAND_HAL_XC_XCVR_CNTL_CNTL_ERROR_LED_MASK; } } return (0); } /************************************************************************* * ide_set_reset ************************************************************************/ #ifdef CONFIG_IDE_RESET void ide_set_reset(int on) { OPTO_FPGA_REGS_ST *opto_ps; opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE; if (on) { /* assert RESET */ opto_ps->reset_ul &= ~SAND_HAL_XC_XCVR_CNTL_RESET_CF_RESET_N_MASK; } else { /* release RESET */ opto_ps->reset_ul |= SAND_HAL_XC_XCVR_CNTL_RESET_CF_RESET_N_MASK; } } #endif /* CONFIG_IDE_RESET */ /************************************************************************* * fpga_init ************************************************************************/ void fpga_init(void) { OPTO_FPGA_REGS_ST *opto_ps; unsigned char opto_rev; unsigned long tmp; /* Ensure we have power all around */ udelay(500); /* * Take appropriate hw bits out of reset */ opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE; tmp = SAND_HAL_XC_XCVR_CNTL_RESET_MAC1_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_MAC0_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_BME_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_ACE_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_CF_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_QE_A_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_IFE_A_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_EFE_A_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_QE_B_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_IFE_B_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_EFE_B_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_LOCK1_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_LOCK0_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_I2C_MUX1_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_I2C_MUX0_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_PHY0_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_PHY1_RESET_N_MASK | SAND_HAL_XC_XCVR_CNTL_RESET_SLAVE_RESET_N_MASK; opto_ps->reset_ul = tmp; /* * Turn on the 'Slow Blink' for the System Error Led. * Ensure FPGA rev is up to at least rev 0x12 */ opto_rev = (unsigned char)((opto_ps->revision_ul & SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_MASK) >> SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_SHIFT); if(0x12 <= opto_rev) { opto_ps->control_ul |= 1 << SAND_HAL_XC_XCVR_CNTL_CNTL_ERROR_LED_SHIFT; } asm("eieio"); return; } int metroboxSetupVars(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) { unsigned short sernum; char envstr[255]; sernum = sbcommon_get_serial_number(); memset(envstr, 0, 255); /* * Setup our ip address */ sprintf(envstr, "10.100.60.%d", sernum); setenv("ipaddr", envstr); /* * Setup the host ip address */ setenv("serverip", "10.100.17.10"); /* * Setup default bootargs */ memset(envstr, 0, 255); sprintf(envstr, "console=ttyS0,9600 root=/dev/nfs " "rw nfsroot=10.100.17.10:/home/metrobox/mbc%d " "nfsaddrs=10.100.60.%d:10.100.17.10:10.100.1.1" ":255.255.0.0:metrobox%d.sandburst.com:eth0:none idebus=33", sernum, sernum, sernum); setenv("bootargs_nfs", envstr); setenv("bootargs", envstr); /* * Setup CF bootargs */ memset(envstr, 0, 255); sprintf(envstr, "console=ttyS0,9600 root=/dev/hda2 " "rw ip=10.100.60.%d:::255.255.0.0:metrobox%d:eth0:none idebus=33", sernum, sernum); setenv("bootargs_cf", envstr); /* * Setup Default boot command */ setenv("bootcmd_tftp", "tftp 8000000 pImage.metrobox;bootm 8000000"); setenv("bootcmd", "tftp 8000000 pImage.metrobox;bootm 8000000"); /* * Setup compact flash boot command */ setenv("bootcmd_cf", "fatload ide 0 8000000 pimage.metrobox;bootm 8000000"); saveenv(); return(1); } int metroboxRecover(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) { unsigned short sernum; char envstr[255]; sernum = sbcommon_get_serial_number(); printf("\nSetting up environment for filesystem recovery\n"); /* * Setup default bootargs */ memset(envstr, 0, 255); sprintf(envstr, "console=ttyS0,9600 root=/dev/ram0 " "rw ip=10.100.60.%d:::255.255.0.0:metrobox%d:eth0:none", sernum, sernum); setenv("bootargs", envstr); /* * Setup Default boot command */ setenv("bootcmd", "fatload ide 0 8000000 pimage.metrobox;" "fatload ide 0 8100000 pramdisk;" "bootm 8000000 8100000"); printf("Done. Please type boot.\nWhen the kernel has booted" " please type fsrecover.sh\n"); return(1); } U_BOOT_CMD(mbsetup, 1, 1, metroboxSetupVars, "mbsetup - Set environment to factory defaults\n", NULL); U_BOOT_CMD(mbrecover, 1, 1, metroboxRecover, "mbrecover - Set environment to allow for fs recovery\n", NULL);