summaryrefslogtreecommitdiff
path: root/drivers/atm/nicstarmac.c
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 15:20:36 -0700
committerLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 15:20:36 -0700
commit1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 (patch)
tree0bba044c4ce775e45a88a51686b5d9f90697ea9d /drivers/atm/nicstarmac.c
Linux-2.6.12-rc2v2.6.12-rc2
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
Diffstat (limited to 'drivers/atm/nicstarmac.c')
-rw-r--r--drivers/atm/nicstarmac.c274
1 files changed, 274 insertions, 0 deletions
diff --git a/drivers/atm/nicstarmac.c b/drivers/atm/nicstarmac.c
new file mode 100644
index 00000000000..2c5e3ae7750
--- /dev/null
+++ b/drivers/atm/nicstarmac.c
@@ -0,0 +1,274 @@
+/*
+ * this file included by nicstar.c
+ */
+
+/*
+ * nicstarmac.c
+ * Read this ForeRunner's MAC address from eprom/eeprom
+ */
+
+typedef void __iomem *virt_addr_t;
+
+#define CYCLE_DELAY 5
+
+/* This was the original definition
+#define osp_MicroDelay(microsec) \
+ do { int _i = 4*microsec; while (--_i > 0) { __SLOW_DOWN_IO; }} while (0)
+*/
+#define osp_MicroDelay(microsec) {unsigned long useconds = (microsec); \
+ udelay((useconds));}
+
+
+/* The following tables represent the timing diagrams found in
+ * the Data Sheet for the Xicor X25020 EEProm. The #defines below
+ * represent the bits in the NICStAR's General Purpose register
+ * that must be toggled for the corresponding actions on the EEProm
+ * to occur.
+ */
+
+/* Write Data To EEProm from SI line on rising edge of CLK */
+/* Read Data From EEProm on falling edge of CLK */
+
+#define CS_HIGH 0x0002 /* Chip select high */
+#define CS_LOW 0x0000 /* Chip select low (active low)*/
+#define CLK_HIGH 0x0004 /* Clock high */
+#define CLK_LOW 0x0000 /* Clock low */
+#define SI_HIGH 0x0001 /* Serial input data high */
+#define SI_LOW 0x0000 /* Serial input data low */
+
+/* Read Status Register = 0000 0101b */
+#if 0
+static u_int32_t rdsrtab[] =
+{
+ CS_HIGH | CLK_HIGH,
+ CS_LOW | CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW | SI_HIGH,
+ CLK_HIGH | SI_HIGH, /* 1 */
+ CLK_LOW | SI_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW | SI_HIGH,
+ CLK_HIGH | SI_HIGH /* 1 */
+};
+#endif /* 0 */
+
+
+/* Read from EEPROM = 0000 0011b */
+static u_int32_t readtab[] =
+{
+ /*
+ CS_HIGH | CLK_HIGH,
+ */
+ CS_LOW | CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW,
+ CLK_HIGH, /* 0 */
+ CLK_LOW | SI_HIGH,
+ CLK_HIGH | SI_HIGH, /* 1 */
+ CLK_LOW | SI_HIGH,
+ CLK_HIGH | SI_HIGH /* 1 */
+};
+
+
+/* Clock to read from/write to the eeprom */
+static u_int32_t clocktab[] =
+{
+ CLK_LOW,
+ CLK_HIGH,
+ CLK_LOW,
+ CLK_HIGH,
+ CLK_LOW,
+ CLK_HIGH,
+ CLK_LOW,
+ CLK_HIGH,
+ CLK_LOW,
+ CLK_HIGH,
+ CLK_LOW,
+ CLK_HIGH,
+ CLK_LOW,
+ CLK_HIGH,
+ CLK_LOW,
+ CLK_HIGH,
+ CLK_LOW
+};
+
+
+#define NICSTAR_REG_WRITE(bs, reg, val) \
+ while ( readl(bs + STAT) & 0x0200 ) ; \
+ writel((val),(base)+(reg))
+#define NICSTAR_REG_READ(bs, reg) \
+ readl((base)+(reg))
+#define NICSTAR_REG_GENERAL_PURPOSE GP
+
+/*
+ * This routine will clock the Read_Status_reg function into the X2520
+ * eeprom, then pull the result from bit 16 of the NicSTaR's General Purpose
+ * register.
+ */
+#if 0
+u_int32_t
+nicstar_read_eprom_status( virt_addr_t base )
+{
+ u_int32_t val;
+ u_int32_t rbyte;
+ int32_t i, j;
+
+ /* Send read instruction */
+ val = NICSTAR_REG_READ( base, NICSTAR_REG_GENERAL_PURPOSE ) & 0xFFFFFFF0;
+
+ for (i=0; i<sizeof rdsrtab/sizeof rdsrtab[0]; i++)
+ {
+ NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | rdsrtab[i]) );
+ osp_MicroDelay( CYCLE_DELAY );
+ }
+
+ /* Done sending instruction - now pull data off of bit 16, MSB first */
+ /* Data clocked out of eeprom on falling edge of clock */
+
+ rbyte = 0;
+ for (i=7, j=0; i>=0; i--)
+ {
+ NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | clocktab[j++]) );
+ rbyte |= (((NICSTAR_REG_READ( base, NICSTAR_REG_GENERAL_PURPOSE)
+ & 0x00010000) >> 16) << i);
+ NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | clocktab[j++]) );
+ osp_MicroDelay( CYCLE_DELAY );
+ }
+ NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE, 2 );
+ osp_MicroDelay( CYCLE_DELAY );
+ return rbyte;
+}
+#endif /* 0 */
+
+
+/*
+ * This routine will clock the Read_data function into the X2520
+ * eeprom, followed by the address to read from, through the NicSTaR's General
+ * Purpose register.
+ */
+
+static u_int8_t
+read_eprom_byte(virt_addr_t base, u_int8_t offset)
+{
+ u_int32_t val = 0;
+ int i,j=0;
+ u_int8_t tempread = 0;
+
+ val = NICSTAR_REG_READ( base, NICSTAR_REG_GENERAL_PURPOSE ) & 0xFFFFFFF0;
+
+ /* Send READ instruction */
+ for (i=0; i<sizeof readtab/sizeof readtab[0]; i++)
+ {
+ NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | readtab[i]) );
+ osp_MicroDelay( CYCLE_DELAY );
+ }
+
+ /* Next, we need to send the byte address to read from */
+ for (i=7; i>=0; i--)
+ {
+ NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | clocktab[j++] | ((offset >> i) & 1) ) );
+ osp_MicroDelay(CYCLE_DELAY);
+ NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | clocktab[j++] | ((offset >> i) & 1) ) );
+ osp_MicroDelay( CYCLE_DELAY );
+ }
+
+ j = 0;
+
+ /* Now, we can read data from the eeprom by clocking it in */
+ for (i=7; i>=0; i--)
+ {
+ NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | clocktab[j++]) );
+ osp_MicroDelay( CYCLE_DELAY );
+ tempread |= (((NICSTAR_REG_READ( base, NICSTAR_REG_GENERAL_PURPOSE )
+ & 0x00010000) >> 16) << i);
+ NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | clocktab[j++]) );
+ osp_MicroDelay( CYCLE_DELAY );
+ }
+
+ NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE, 2 );
+ osp_MicroDelay( CYCLE_DELAY );
+ return tempread;
+}
+
+
+static void
+nicstar_init_eprom( virt_addr_t base )
+{
+ u_int32_t val;
+
+ /*
+ * turn chip select off
+ */
+ val = NICSTAR_REG_READ(base, NICSTAR_REG_GENERAL_PURPOSE) & 0xFFFFFFF0;
+
+ NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | CS_HIGH | CLK_HIGH));
+ osp_MicroDelay( CYCLE_DELAY );
+
+ NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | CS_HIGH | CLK_LOW));
+ osp_MicroDelay( CYCLE_DELAY );
+
+ NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | CS_HIGH | CLK_HIGH));
+ osp_MicroDelay( CYCLE_DELAY );
+
+ NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
+ (val | CS_HIGH | CLK_LOW));
+ osp_MicroDelay( CYCLE_DELAY );
+}
+
+
+/*
+ * This routine will be the interface to the ReadPromByte function
+ * above.
+ */
+
+static void
+nicstar_read_eprom(
+ virt_addr_t base,
+ u_int8_t prom_offset,
+ u_int8_t *buffer,
+ u_int32_t nbytes )
+{
+ u_int i;
+
+ for (i=0; i<nbytes; i++)
+ {
+ buffer[i] = read_eprom_byte( base, prom_offset );
+ ++prom_offset;
+ osp_MicroDelay( CYCLE_DELAY );
+ }
+}
+
+
+/*
+void osp_MicroDelay(int x) {
+
+}
+*/
+