85xx: Add P2020DS support

The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.

Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

1 files changed, 741 insertions, 0 deletions

diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h
new file mode 100644
index 000000000..a39ff26a7
--- /dev/null
+++ b/include/configs/P2020DS.h
@@ -0,0 +1,741 @@
+/*
+ * Copyright 2007-2009 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * p2020ds board configuration file
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
+#define CONFIG_P2020		1
+#define CONFIG_P2020DS		1
+#define CONFIG_MP		1	/* support multiple processors */
+#define CONFIG_NUM_CPUS		2	/* Number of CPUs in the system */
+
+#define CONFIG_FSL_ELBC		1	/* Has Enhanced localbus controller */
+#define CONFIG_PCI		1	/* Enable PCI/PCIE */
+#define CONFIG_PCIE1		1	/* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2		1	/* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE3		1	/* PCIE controler 3 (ULI bridge) */
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
+
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
+
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * When initializing flash, if we cannot find the manufacturer ID,
+ * assume this is the AMD flash associated with the CDS board.
+ * This allows booting from a promjet.
+ */
+#define CONFIG_ASSUME_AMD_FLASH
+
+#ifndef __ASSEMBLY__
+extern unsigned long calculate_board_sys_clk(unsigned long dummy);
+extern unsigned long calculate_board_ddr_clk(unsigned long dummy);
+/* extern unsigned long get_board_sys_clk(unsigned long dummy); */
+/* extern unsigned long get_board_ddr_clk(unsigned long dummy); */
+#endif
+#define CONFIG_SYS_CLK_FREQ	calculate_board_sys_clk(0) /* sysclk for MPC85xx */
+#define CONFIG_DDR_CLK_FREQ	calculate_board_ddr_clk(0) /* ddrclk for MPC85xx */
+#define CONFIG_ICS307_REFCLK_HZ	33333000  /* ICS307 clock chip ref freq */
+#define CONFIG_GET_CLK_FROM_ICS307	  /* decode sysclk and ddrclk freq
+					     from ICS307 instead of switches */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+
+#define CONFIG_ENABLE_36BIT_PHYS	1
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP			1
+#define CONFIG_SYS_NUM_ADDR_MAP		16	/* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x7fffffff
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS		0xfffe00000ull	/* physical addr of CCSRBAR */
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
+#endif
+#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+
+#define CONFIG_SYS_PCIE3_ADDR		(CONFIG_SYS_CCSRBAR+0x8000)
+#define CONFIG_SYS_PCIE2_ADDR		(CONFIG_SYS_CCSRBAR+0x9000)
+#define CONFIG_SYS_PCIE1_ADDR		(CONFIG_SYS_CCSRBAR+0xa000)
+
+/* DDR Setup */
+#define CONFIG_SYS_DDR_TLB_START 9
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_FSL_DDR3		1
+#undef CONFIG_FSL_DDR_INTERACTIVE
+
+// #define	CONFIG_DDR_ECC /* ECC will be enabled based on perf_mode environment variable */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define CONFIG_SYS_SPD_BUS_NUM		0	/* SPD EEPROM located on I2C bus 0 */
+#define SPD_EEPROM_ADDRESS1	0x51	/* CTLR 0 DIMM 0 */
+
+/* These are used when DDR doesn't use SPD.  */
+//#define CONFIG_SYS_SDRAM_SIZE		512		/* DDR is 512MB */
+#define CONFIG_SYS_SDRAM_SIZE		1024		/* DDR is 1GB */
+
+/* Default settings for "stable" mode */
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000003F
+#define CONFIG_SYS_DDR_CS1_BNDS		0x00000000
+#define CONFIG_SYS_DDR_CS0_CONFIG	0x80014202
+#define CONFIG_SYS_DDR_CS1_CONFIG	0x00000000
+#define CONFIG_SYS_DDR_TIMING_3		0x00020000
+#define CONFIG_SYS_DDR_TIMING_0		0x00330804
+#define CONFIG_SYS_DDR_TIMING_1		0x6f6b4846
+#define CONFIG_SYS_DDR_TIMING_2		0x0fa890d4
+#define CONFIG_SYS_DDR_MODE_1		0x00421422
+#define CONFIG_SYS_DDR_MODE_2		0x00000000
+#define CONFIG_SYS_DDR_MODE_CTRL	0x00000000
+#define CONFIG_SYS_DDR_INTERVAL		0x61800100
+#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
+#define CONFIG_SYS_DDR_CLK_CTRL		0x02000000
+#define CONFIG_SYS_DDR_TIMING_4		0x00220001
+#define CONFIG_SYS_DDR_TIMING_5		0x03402400
+#define CONFIG_SYS_DDR_ZQ_CNTL		0x89080600
+#define CONFIG_SYS_DDR_WRLVL_CNTL	0x8655A608
+#define CONFIG_SYS_DDR_CONTROL		0xE7000000 /* Type = DDR3: ECC enabled, No Interleaving */
+#define CONFIG_SYS_DDR_CONTROL2		0x24400011
+#define CONFIG_SYS_DDR_CDR1		0x00040000
+#define CONFIG_SYS_DDR_CDR2		0x00000000
+
+#define CONFIG_SYS_DDR_ERR_INT_EN	0x0000000d
+#define CONFIG_SYS_DDR_ERR_DIS		0x00000000
+#define CONFIG_SYS_DDR_SBE		0x00010000
+
+/* Settings that differ for "performance" mode */
+#define CONFIG_SYS_DDR_CS0_BNDS_PERF		0x0000007F /* Interleaving Enabled */
+#define CONFIG_SYS_DDR_CS1_BNDS_PERF		0x00000000 /* Interleaving Enabled */
+#define CONFIG_SYS_DDR_CS1_CONFIG_PERF	0x80014202
+#define CONFIG_SYS_DDR_TIMING_1_PERF		0x5d5b4543
+#define CONFIG_SYS_DDR_TIMING_2_PERF		0x0fa890ce
+#define CONFIG_SYS_DDR_CONTROL_PERF		0xC7004000 /* Type = DDR3: ECC disabled, cs0-cs1 interleaving */
+
+/*
+ * The following set of values were tested for DDR2
+ * with a DDR3 to DDR2 interposer
+ *
+#define CONFIG_SYS_DDR_TIMING_3		0x00000000
+#define CONFIG_SYS_DDR_TIMING_0		0x00260802
+#define CONFIG_SYS_DDR_TIMING_1		0x3935d322
+#define CONFIG_SYS_DDR_TIMING_2		0x14904cc8
+#define CONFIG_SYS_DDR_MODE_1		0x00480432
+#define CONFIG_SYS_DDR_MODE_2		0x00000000
+#define CONFIG_SYS_DDR_INTERVAL		0x06180100
+#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
+#define CONFIG_SYS_DDR_CLK_CTRL		0x03800000
+#define CONFIG_SYS_DDR_OCD_CTRL		0x00000000
+#define CONFIG_SYS_DDR_OCD_STATUS	0x00000000
+#define CONFIG_SYS_DDR_CONTROL		0xC3008000
+#define CONFIG_SYS_DDR_CONTROL2		0x04400010
+ *
+ */
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
+ * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
+ * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
+ * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
+ *
+ * Localbus cacheable (TBD)
+ * 0xXXXX_XXXX	0xXXXX_XXXX	SRAM			YZ M Cacheable
+ *
+ * Localbus non-cacheable
+ * 0xe000_0000	0xe80f_ffff	Promjet/free		128M non-cacheable
+ * 0xe800_0000	0xefff_ffff	FLASH			128M non-cacheable
+ * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
+ * 0xffdf_0000	0xffdf_7fff	PIXIS			32K non-cacheable TLB0
+ * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
+ * 0xffe0_0000	0xffef_ffff	CCSR			1M non-cacheable
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE		0xe0000000	/* start of FLASH 128M */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS	0xfe0000000ull
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_FLASH_BR_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V)
+#define CONFIG_FLASH_OR_PRELIM	0xf8000ff7
+
+#define CONFIG_SYS_BR1_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM	0xf8000ff7
+
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
+#undef	CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
+
+#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+
+#define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
+#define PIXIS_BASE	0xffdf0000	/* PIXIS registers */
+#ifdef CONFIG_PHYS_64BIT
+#define PIXIS_BASE_PHYS	0xfffdf0000ull
+#else
+#define PIXIS_BASE_PHYS	PIXIS_BASE
+#endif
+
+#define CONFIG_SYS_BR3_PRELIM	(BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR3_PRELIM		0xffffeff7	/* 32KB but only 4k mapped */
+
+#define PIXIS_ID		0x0	/* Board ID at offset 0 */
+#define PIXIS_VER		0x1	/* Board version at offset 1 */
+#define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
+#define PIXIS_CSR		0x3	/* PIXIS General control/status register */
+#define PIXIS_RST		0x4	/* PIXIS Reset Control register */
+#define PIXIS_PWR		0x5	/* PIXIS Power status register */
+#define PIXIS_AUX		0x6	/* Auxiliary 1 register */
+#define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
+#define PIXIS_AUX2		0x8	/* Auxiliary 2 register */
+#define PIXIS_VCTL		0x10	/* VELA Control Register */
+#define PIXIS_VSTAT		0x11	/* VELA Status Register */
+#define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
+#define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
+#define PIXIS_VCORE0		0x14	/* VELA VCORE0 Register */
+#define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
+#define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
+#define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
+#define PIXIS_VSPEED2		0x19	/* VELA VSpeed 2 */
+#define PIXIS_VSYSCLK0		0x19	/* VELA SYSCLK0 Register */
+#define PIXIS_VSYSCLK1		0x1A	/* VELA SYSCLK1 Register */
+#define PIXIS_VSYSCLK2		0x1B	/* VELA SYSCLK2 Register */
+#define PIXIS_VDDRCLK0		0x1C	/* VELA DDRCLK0 Register */
+#define PIXIS_VDDRCLK1		0x1D	/* VELA DDRCLK1 Register */
+#define PIXIS_VDDRCLK2		0x1E	/* VELA DDRCLK2 Register */
+
+#define PIXIS_VWATCH		0x24	/* Watchdog Register */
+#define PIXIS_LED		0x25	/* LED Register */
+
+/* old pixis referenced names */
+#define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
+#define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+#define CONFIG_SYS_PIXIS_VBOOT_MASK	0xc0
+#define PIXIS_VSPEED2_TSEC1SER	0x8
+#define PIXIS_VSPEED2_TSEC2SER	0x4
+#define PIXIS_VSPEED2_TSEC3SER	0x2
+#define PIXIS_VSPEED2_TSEC4SER	0x1
+#define PIXIS_VCFGEN1_TSEC1SER	0x20
+#define PIXIS_VCFGEN1_TSEC2SER	0x20
+#define PIXIS_VCFGEN1_TSEC3SER	0x20
+#define PIXIS_VCFGEN1_TSEC4SER	0x20
+#define PIXIS_VSPEED2_MASK	(PIXIS_VSPEED2_TSEC1SER \
+					| PIXIS_VSPEED2_TSEC2SER \
+					| PIXIS_VSPEED2_TSEC3SER \
+					| PIXIS_VSPEED2_TSEC4SER)
+#define PIXIS_VCFGEN1_MASK	(PIXIS_VCFGEN1_TSEC1SER \
+					| PIXIS_VCFGEN1_TSEC2SER \
+					| PIXIS_VCFGEN1_TSEC3SER \
+					| PIXIS_VCFGEN1_TSEC4SER)
+
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_END	0x00004000	/* End of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
+
+#define CONFIG_SYS_NAND_BASE		0xffa00000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS	0xfffa00000ull
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+#endif
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE,\
+				CONFIG_SYS_NAND_BASE + 0x40000, \
+				CONFIG_SYS_NAND_BASE + 0x80000,\
+				CONFIG_SYS_NAND_BASE + 0xC0000}
+#define CONFIG_SYS_MAX_NAND_DEVICE	4
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND			1
+#define CONFIG_NAND_FSL_ELBC		1
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+
+/* NAND flash config */
+#define CONFIG_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
+				| BR_PS_8		/* Port Size = 8bit */ \
+				| BR_MS_FCM		/* MSEL = FCM */ \
+				| BR_V)			/* valid */
+#define CONFIG_NAND_OR_PRELIM  (0xFFFC0000		/* length 256K */ \
+				| OR_FCM_PGS		/* Large Page*/ \
+				| OR_FCM_CSCT \
+				| OR_FCM_CST \
+				| OR_FCM_CHT \
+				| OR_FCM_SCY_1 \
+				| OR_FCM_TRLX \
+				| OR_FCM_EHTR)
+
+#define CONFIG_SYS_BR0_PRELIM  CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
+#define CONFIG_SYS_OR0_PRELIM  CONFIG_FLASH_OR_PRELIM  /* NOR Options */
+#define CONFIG_SYS_BR2_PRELIM  CONFIG_NAND_BR_PRELIM  /* NAND Base Address */
+#define CONFIG_SYS_OR2_PRELIM  CONFIG_NAND_OR_PRELIM  /* NAND Options */
+
+#define CONFIG_SYS_BR4_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x40000))\
+				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
+				| BR_PS_8		/* Port Size = 8bit */ \
+				| BR_MS_FCM		/* MSEL = FCM */ \
+				| BR_V)			/* valid */
+#define CONFIG_SYS_OR4_PRELIM  CONFIG_NAND_OR_PRELIM	/* NAND Options */
+#define CONFIG_SYS_BR5_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x80000))\
+				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
+				| BR_PS_8		/* Port Size = 8bit */ \
+				| BR_MS_FCM		/* MSEL = FCM */ \
+				| BR_V)			/* valid */
+#define CONFIG_SYS_OR5_PRELIM  CONFIG_NAND_OR_PRELIM	/* NAND Options */
+
+#define CONFIG_SYS_BR6_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0xc0000))\
+				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
+				| BR_PS_8		/* Port Size = 8bit */ \
+				| BR_MS_FCM		/* MSEL = FCM */ \
+				| BR_V)			/* valid */
+#define CONFIG_SYS_OR6_PRELIM  CONFIG_NAND_OR_PRELIM	/* NAND Options */
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX	1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef	CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+#define CONFIG_SYS_64BIT_VSPRINTF	1
+#define CONFIG_SYS_64BIT_STRTOUL	1
+
+/* new uImage format support */
+#define CONFIG_FIT		1
+#define CONFIG_FIT_VERBOSE	1 /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_NOPROBES	{{0,0x29}}/* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C2_OFFSET		0x3100
+
+/*
+ * I2C2 EEPROM
+ */
+#define CONFIG_ID_EEPROM
+#ifdef CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#endif
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_BUS_NUM	0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 3, Slot 1, tgtid 3, Base address b000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0x80000000
+#endif
+#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
+#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xfffc00000ull
+#else
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xffc00000
+#endif
+#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 2, direct to uli, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xfffc10000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
+#endif
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 1, Slot 2, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc40000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc0000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xfffc20000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc20000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+#if defined(CONFIG_PCI)
+
+/*PCIE video card used*/
+#define VIDEO_IO_OFFSET		CONFIG_SYS_PCIE1_IO_VIRT
+
+/* video */
+#define CONFIG_VIDEO
+
+#if defined(CONFIG_VIDEO)
+#define CONFIG_BIOSEMU
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+/*#define CONFIG_CONSOLE_CURSOR*/
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#endif
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+#define CONFIG_RTL8139
+
+#ifdef CONFIG_RTL8139
+/* This macro is used by RTL8139 but not defined in PPC architecture */
+#define KSEG1ADDR(x)		(x)
+#define _IO_BASE	0x00000000
+#endif
+
+#ifndef CONFIG_PCI_PNP
+	#define PCI_ENET0_IOADDR	CONFIG_SYS_PCIE3_IO_BUS
+	#define PCI_ENET0_MEMADDR	CONFIG_SYS_PCIE3_IO_BUS
+	#define PCI_IDSEL_NUMBER	0x11	/* IDSEL = AD11 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID	4
+#define CONFIG_SYS_SCSI_MAX_LUN	1
+#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_SYS_SCSI_MAXDEVICE	CONFIG_SYS_SCSI_MAX_DEVICE
+#endif /* SCSI */
+
+#endif	/* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI	1
+#endif
+
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
+#define CONFIG_TSEC1	1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#define CONFIG_TSEC2	1
+#define CONFIG_TSEC2_NAME	"eTSEC2"
+#define CONFIG_TSEC3	1
+#define CONFIG_TSEC3_NAME	"eTSEC3"
+
+#define CONFIG_PIXIS_SGMII_CMD
+#define CONFIG_FSL_SGMII_RISER	1
+#define SGMII_RISER_PHY_OFFSET	0x1b
+
+#ifdef CONFIG_FSL_SGMII_RISER
+#define CONFIG_SYS_TBIPA_VALUE		0x10 /* avoid conflict with eTSEC4 paddr */
+#endif
+
+#define TSEC1_PHY_ADDR		0
+#define TSEC2_PHY_ADDR		1
+#define TSEC3_PHY_ADDR		2
+
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define TSEC3_PHYIDX		0
+
+#define CONFIG_ETHPRIME		"eTSEC1"
+
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR		0xfff80000
+#else
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#endif
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_SETEXPR
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_SCSI
+#define CONFIG_CMD_EXT2
+#endif
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR	00:E0:0C:02:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR	00:E0:0C:02:01:FD
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR	00:E0:0C:02:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR	00:E0:0C:02:03:FD
+#endif
+
+#define CONFIG_IPADDR		192.168.1.254
+
+#define CONFIG_HOSTNAME		unknown
+#define CONFIG_ROOTPATH		/opt/nfsroot
+#define CONFIG_BOOTFILE		uImage
+#define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */
+
+#define CONFIG_SERVERIP		192.168.1.1
+#define CONFIG_GATEWAYIP	192.168.1.1
+#define CONFIG_NETMASK		255.255.255.0
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+ "perf_mode=stable\0"			\
+ "memctl_intlv_ctl=2\0"						\
+ "netdev=eth0\0"						\
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+ "tftpflash=tftpboot $loadaddr $uboot; "			\
+	"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
+	"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
+	"protect on " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
+ "consoledev=ttyS0\0"				\
+ "ramdiskaddr=2000000\0"			\
+ "ramdiskfile=p2020ds/ramdisk.uboot\0"		\
+ "fdtaddr=c00000\0"				\
+ "fdtfile=p2020ds/p2020ds.dtb\0"		\
+ "bdev=sda3\0"
+
+#define CONFIG_HDBOOT				\
+ "setenv bootargs root=/dev/$bdev rw "		\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $loadaddr $bootfile;"			\
+ "tftp $fdtaddr $fdtfile;"			\
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND		\
+ "setenv bootargs root=/dev/nfs rw "	\
+ "nfsroot=$serverip:$rootpath "		\
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $loadaddr $bootfile;"		\
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND		\
+ "setenv bootargs root=/dev/ram rw "	\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $ramdiskaddr $ramdiskfile;"	\
+ "tftp $loadaddr $bootfile;"		\
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_HDBOOT
+
+#endif	/* __CONFIG_H */