ppc4xx: Update configs for Netstal boards

I reorganized my config files, putting the common stuff into netstal-common.h
(got the idea by looking a amcc-common.h from Stefan).

Added stuff to boot the new powerpc linux via NFS (only tested with HCU4).

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
Signed-off-by: Stefan Roese <sr@denx.de>

1 files changed, 11 insertions, 83 deletions

diff --git a/include/configs/mcu25.h b/include/configs/mcu25.h
index e4489696b..5f3119883 100644
--- a/include/configs/mcu25.h
+++ b/include/configs/mcu25.h
@@ -35,6 +35,12 @@
 #define CONFIG_4xx		1		/* ... PPC4xx family	*/
 #define CONFIG_405GP 1
 #define CONFIG_4xx   1
+#define CONFIG_HOSTNAME		mcu25
+
+/*
+ * Include common defines/options for all boards produced by Netstal Maschinen
+ */
+#include "netstal-common.h"
 
 #define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll	*/
 
@@ -80,8 +86,6 @@
  * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
  * set Linux BASE_BAUD to 403200.
  */
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK	       /* external serial clock */
-#define CONFIG_SERIAL_MULTI  1
 /* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */
 #undef	CONFIG_SYS_405_UART_ERRATA_59	       /* 405GP/CR Rev. D silicon */
 #define CONFIG_SYS_BASE_BAUD	    691200
@@ -95,10 +99,6 @@
 /* Set console baudrate to 9600 */
 #define CONFIG_BAUDRATE		9600
 
-
-#define CONFIG_SYS_BAUDRATE_TABLE						\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * Flash
  *----------------------------------------------------------------------*/
@@ -149,74 +149,13 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_SPD_BUS_NUM		0
 
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/* This is the 7bit address of the device, not including P. */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#undef CONFIG_SYS_I2C_MULTI_EEPROMS
-
-
-#define CONFIG_PREBOOT	"echo;"						\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
 /* Setup some board specific values for the default environment variables */
-#define CONFIG_HOSTNAME		mcu25
-#define CONFIG_IPADDR		172.25.1.99
-#define CONFIG_ETHADDR      00:60:13:00:00:00   /* Netstal Machines AG MAC */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-#define CONFIG_SERVERIP		172.25.1.3
-
-#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 /* @16 MB */
-
-#define	CONFIG_EXTRA_ENV_SETTINGS				\
-	"netdev=eth0\0"							\
-	"loadaddr=0x01000000\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"		\
-	        "bootm\0"						\
-	"rootpath=/home/diagnose/eldk/ppc_4xx\0"			\
-	"bootfile=/tftpboot/mcu25/uImage\0"				\
-	"load=tftp 100000 mcu25/u-boot.bin\0"				\
-	"update=protect off FFFB0000 FFFFFFFF;era FFFB0000 FFFFFFFF;"	\
-		"cp.b 100000 FFFB0000 50000\0"			        \
-	"upd=run load;run update\0"					\
-	"vx_rom=mcu25/mcu25_vx_rom\0"					\
-	"vx=tftp ${loadaddr} ${vx_rom};run vxargs; bootvx\0"		\
-	"vxargs=setenv bootargs emac(0,0)c:${vx_rom} e=${ipaddr}"	\
-	" h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0"	\
-	""
-#define CONFIG_BOOTCOMMAND	"run vx"
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR	1	/* PHY address			*/
+#define CONFIG_IPADDR		172.25.1.25
 
-#define CONFIG_PHY_RESET        1	/* reset phy upon startup */
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_SYS_RX_ETH_BUFFER	16 /* Number of ethernet rx buffers & descr */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CONFIG_NETSTAL_DEF_ENV						\
+	CONFIG_NETSTAL_DEF_ENV_POWERPC					\
+	""
 
 /*
  * BOOTP options
@@ -285,13 +224,6 @@
 
 
 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
@@ -353,8 +285,4 @@
 #define CONFIG_KGDB_SER_INDEX	2	    /* which serial port to use */
 #endif
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */