diff options
| -rw-r--r-- | board/mx31ads/mx31ads.c | 16 | ||||
| -rw-r--r-- | board/mx31ads/u-boot.lds | 13 | ||||
| -rw-r--r-- | include/configs/mx31ads.h | 29 |
3 files changed, 42 insertions, 16 deletions
diff --git a/board/mx31ads/mx31ads.c b/board/mx31ads/mx31ads.c index 7c50c023e..5a7d8c91c 100644 --- a/board/mx31ads/mx31ads.c +++ b/board/mx31ads/mx31ads.c @@ -38,18 +38,18 @@ int dram_init (void) int board_init (void) { int i; -#if 0 + /* CS0: Nor Flash */ /* - * These are values from the RedBoot sources by Freescale. However, - * under U-Boot with this configuration 32-bit accesses don't work, - * lower 16 bits of data are read twice for each 32-bit read. + * CS0L and CS0A values are from the RedBoot sources by Freescale + * and are also equal to those used by Sascha Hauer for the Phytec + * i.MX31 board. CS0U is just a slightly optimized hardware default: + * the only non-zero field "Wait State Control" is set to half the + * default value. */ - __REG(CSCR_U(0)) = 0x23524E80; - __REG(CSCR_L(0)) = 0x10000D03; /* WRAP bit (1) is suspicious here, but - * disabling it doesn't help either */ + __REG(CSCR_U(0)) = 0x00000f00; + __REG(CSCR_L(0)) = 0x10000D03; __REG(CSCR_A(0)) = 0x00720900; -#endif /* setup pins for UART1 */ mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX); diff --git a/board/mx31ads/u-boot.lds b/board/mx31ads/u-boot.lds index 1460adcdd..49713d454 100644 --- a/board/mx31ads/u-boot.lds +++ b/board/mx31ads/u-boot.lds @@ -34,7 +34,18 @@ SECTIONS . = ALIGN(4); .text : { - cpu/arm1136/start.o (.text) + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/arm1136/start.o (.text) + board/mx31ads/libmx31ads.a (.text) + lib_arm/libarm.a (.text) + net/libnet.a (.text) + drivers/mtd/libmtd.a (.text) + + . = DEFINED(env_offset) ? env_offset : .; + common/environment.o(.text) + *(.text) } diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h index 77a9a8366..78e2545ff 100644 --- a/include/configs/mx31ads.h +++ b/include/configs/mx31ads.h @@ -72,7 +72,6 @@ #include <config_cmd_default.h> -#define CONFIG_CMD_MII #define CONFIG_CMD_PING #define CONFIG_BOOTDELAY 3 @@ -91,7 +90,19 @@ #define CONFIG_DRIVER_CS8900 1 #define CS8900_BASE 0xb4020300 -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CS8900_BUS16 1 /* follow the Linux driver */ + +/* + * The MX31ADS board seems to have a hardware "peculiarity" confirmed under + * U-Boot, RedBoot and Linux: the ethernet Rx signal is reaching the CS8900A + * controller inverted. The controller is capable of detecting and correcting + * this, but it needs 4 network packets for that. Which means, at startup, you + * will not receive answers to the first 4 packest, unless there have been some + * broadcasts on the network, or your board is on a hub. Reducing the ARP + * timeout from default 5 seconds to 200ms we speed up the initial TFTP + * transfer, should the user wish one, significantly. + */ +#define CONFIG_ARP_TIMEOUT 200UL /* * Miscellaneous configurable options @@ -100,7 +111,7 @@ #define CFG_PROMPT "=> " #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ @@ -136,25 +147,29 @@ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 262 /* max number of sectors on one chip */ #define CFG_MONITOR_BASE CFG_FLASH_BASE /* Monitor at beginning of flash */ -#define CFG_MONITOR_LEN (128 * 1024) /* Reserve 128KiB */ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256KiB */ #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_SECT_SIZE (32 * 1024) #define CFG_ENV_SIZE CFG_ENV_SECT_SIZE + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE + /* S29WS256N NOR flash has 4 32KiB small sectors at the beginning and at the end. * The rest of 32MiB is in 128KiB big sectors. U-Boot occupies the low 4 sectors, * if we put environment next to it, we will have to occupy 128KiB for it. * Putting it at the top of flash we use only 32KiB. */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 32 * 1024 * 1024 - CFG_ENV_SIZE) +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_ENV_SECT_SIZE) /*----------------------------------------------------------------------- * CFI FLASH driver setup */ #define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */ #define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */ -#if 0 /* Doesn't work yet, work in progress */ +#define CONFIG_FLASH_SPANSION_S29WS_N 1 /* A non-standard buffered write algorithm */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */ -#endif #define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */ /* |