diff options
59 files changed, 3668 insertions, 83 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index f04879555..60def0c34 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -411,6 +411,10 @@ Rune Torgersen <runet@innovsys.com> MPC8266ADS MPC8266 +Peter Tyser <ptyser@xes-inc.com> + + XPEDITE5200 MPC8548 + XPEDITE5370 MPC8572 David Updegraff <dave@cray.com> @@ -385,6 +385,8 @@ LIST_85xx=" \ TQM8548 \ TQM8555 \ TQM8560 \ + XPEDITE5200 \ + XPEDITE5370 \ " ######################################################################### @@ -228,6 +228,7 @@ LIBS += drivers/bios_emulator/libatibiosemu.a LIBS += drivers/block/libblock.a LIBS += drivers/dma/libdma.a LIBS += drivers/fpga/libfpga.a +LIBS += drivers/gpio/libgpio.a LIBS += drivers/hwmon/libhwmon.a LIBS += drivers/i2c/libi2c.a LIBS += drivers/input/libinput.a @@ -407,6 +408,7 @@ TAG_SUBDIRS += disk TAG_SUBDIRS += common TAG_SUBDIRS += drivers/bios_emulator TAG_SUBDIRS += drivers/block +TAG_SUBDIRS += drivers/gpio TAG_SUBDIRS += drivers/hwmon TAG_SUBDIRS += drivers/i2c TAG_SUBDIRS += drivers/input @@ -2461,6 +2463,12 @@ TQM8560_config: unconfig echo "#define CONFIG_BOARDNAME \"TQM$${CTYPE}\"">>$(obj)include/config.h; @$(MKCONFIG) -a TQM85xx ppc mpc85xx tqm85xx tqc +XPEDITE5200_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc mpc85xx xpedite5200 xes + +XPEDITE5370_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc mpc85xx xpedite5370 xes + ######################################################################### ## MPC86xx Systems ######################################################################### @@ -621,6 +621,8 @@ The following options need to be configured: CONFIG_CMD_MII * MII utility commands CONFIG_CMD_NAND * NAND support CONFIG_CMD_NET bootp, tftpboot, rarpboot + CONFIG_CMD_PCA953X * PCA953x I2C gpio commands + CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command CONFIG_CMD_PCI * pciinfo CONFIG_CMD_PCMCIA * PCMCIA support CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network @@ -698,6 +700,13 @@ The following options need to be configured: Note that if the RTC uses I2C, then the I2C interface must also be configured. See I2C Support, below. +- GPIO Support: + CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO + CONFIG_PCA953X_INFO - enable pca953x info command + + Note that if the GPIO device uses I2C, then the I2C interface + must also be configured. See I2C Support, below. + - Timestamp Support: When CONFIG_TIMESTAMP is selected, the timestamp diff --git a/board/freescale/mpc8540ads/mpc8540ads.c b/board/freescale/mpc8540ads/mpc8540ads.c index a0b6fbd12..9e3f67768 100644 --- a/board/freescale/mpc8540ads/mpc8540ads.c +++ b/board/freescale/mpc8540ads/mpc8540ads.c @@ -133,7 +133,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/freescale/mpc8541cds/mpc8541cds.c b/board/freescale/mpc8541cds/mpc8541cds.c index 7e40c5c80..e6025c8a5 100644 --- a/board/freescale/mpc8541cds/mpc8541cds.c +++ b/board/freescale/mpc8541cds/mpc8541cds.c @@ -308,7 +308,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/freescale/mpc8548cds/mpc8548cds.c b/board/freescale/mpc8548cds/mpc8548cds.c index c562fc9d9..90e89bc71 100644 --- a/board/freescale/mpc8548cds/mpc8548cds.c +++ b/board/freescale/mpc8548cds/mpc8548cds.c @@ -125,7 +125,7 @@ local_bus_init(void) sys_info_t sysinfo; get_sys_info(&sysinfo); - clkdiv = (lbc->lcrr & 0x0f) * 2; + clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; gur->lbiuiplldcr1 = 0x00078080; diff --git a/board/freescale/mpc8555cds/mpc8555cds.c b/board/freescale/mpc8555cds/mpc8555cds.c index 33685c19f..53d5a936a 100644 --- a/board/freescale/mpc8555cds/mpc8555cds.c +++ b/board/freescale/mpc8555cds/mpc8555cds.c @@ -308,7 +308,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/freescale/mpc8560ads/mpc8560ads.c b/board/freescale/mpc8560ads/mpc8560ads.c index 37308189d..ac7778e25 100644 --- a/board/freescale/mpc8560ads/mpc8560ads.c +++ b/board/freescale/mpc8560ads/mpc8560ads.c @@ -337,7 +337,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/freescale/mpc8568mds/mpc8568mds.c b/board/freescale/mpc8568mds/mpc8568mds.c index bc93be80f..7a23b338a 100644 --- a/board/freescale/mpc8568mds/mpc8568mds.c +++ b/board/freescale/mpc8568mds/mpc8568mds.c @@ -188,7 +188,7 @@ local_bus_init(void) sys_info_t sysinfo; get_sys_info(&sysinfo); - clkdiv = (lbc->lcrr & 0x0f) * 2; + clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; gur->lbiuiplldcr1 = 0x00078080; diff --git a/board/mpc8540eval/mpc8540eval.c b/board/mpc8540eval/mpc8540eval.c index fa0a33686..bf270f4ce 100644 --- a/board/mpc8540eval/mpc8540eval.c +++ b/board/mpc8540eval/mpc8540eval.c @@ -101,7 +101,7 @@ phys_size_t initdram (int board_type) #if !defined(CONFIG_RAM_AS_FLASH) /* LocalBus is not emulating flash */ get_sys_info(&sysinfo); /* if localbus freq is less than 66MHz,we use bypass mode,otherwise use DLL */ - if(sysinfo.freqSystemBus/(CONFIG_SYS_LBC_LCRR & 0x0f) < 66000000) { + if(sysinfo.freqSystemBus/(CONFIG_SYS_LBC_LCRR & LCRR_CLKDIV) < 66000000) { lbc->lcrr = (CONFIG_SYS_LBC_LCRR & 0x0fffffff)| 0x80000000; } else { lbc->lcrr = CONFIG_SYS_LBC_LCRR & 0x7fffffff; diff --git a/board/pm854/pm854.c b/board/pm854/pm854.c index fed0ed431..5353d738b 100644 --- a/board/pm854/pm854.c +++ b/board/pm854/pm854.c @@ -150,7 +150,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/pm856/pm856.c b/board/pm856/pm856.c index 932f1121e..b14a3d34b 100644 --- a/board/pm856/pm856.c +++ b/board/pm856/pm856.c @@ -306,7 +306,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/sbc8548/sbc8548.c b/board/sbc8548/sbc8548.c index 8c073cb4b..519b0f749 100644 --- a/board/sbc8548/sbc8548.c +++ b/board/sbc8548/sbc8548.c @@ -126,7 +126,7 @@ local_bus_init(void) sys_info_t sysinfo; get_sys_info(&sysinfo); - clkdiv = (lbc->lcrr & 0x0f) * 2; + clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; gur->lbiuiplldcr1 = 0x00078080; diff --git a/board/socrates/socrates.c b/board/socrates/socrates.c index d83dc7d6a..df9696e69 100644 --- a/board/socrates/socrates.c +++ b/board/socrates/socrates.c @@ -156,7 +156,7 @@ void local_bus_init (void) uint lcrr = CONFIG_SYS_LBC_LCRR; get_sys_info (&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_mhz = sysinfo.freqSystemBus / 1000000 / clkdiv; /* Disable PLL bypass for Local Bus Clock >= 66 MHz */ diff --git a/board/tqc/tqm85xx/tqm85xx.c b/board/tqc/tqm85xx/tqm85xx.c index 73f1d01bd..cda8208ee 100644 --- a/board/tqc/tqm85xx/tqm85xx.c +++ b/board/tqc/tqm85xx/tqm85xx.c @@ -361,7 +361,7 @@ uint get_lbc_clock (void) { volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); sys_info_t sys_info; - ulong clkdiv = lbc->lcrr & 0x0f; + ulong clkdiv = lbc->lcrr & LCRR_CLKDIV; get_sys_info (&sys_info); diff --git a/board/xes/common/Makefile b/board/xes/common/Makefile new file mode 100644 index 000000000..e7620f447 --- /dev/null +++ b/board/xes/common/Makefile @@ -0,0 +1,57 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +ifneq ($(OBJTREE),$(SRCTREE)) +$(shell mkdir -p $(obj)board/$(VENDOR)/common) +endif + +LIB = $(obj)lib$(VENDOR).a + +COBJS-$(CONFIG_FSL_PCI_INIT) += fsl_85xx_pci.o +COBJS-$(CONFIG_MPC8572) += fsl_8572_clk.o +COBJS-$(CONFIG_MPC85xx) += fsl_85xx_ddr.o +COBJS-$(CONFIG_NAND_ACTL) += actl_nand.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/xes/common/actl_nand.c b/board/xes/common/actl_nand.c new file mode 100644 index 000000000..465aeb099 --- /dev/null +++ b/board/xes/common/actl_nand.c @@ -0,0 +1,65 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * This driver support NAND devices which have address lines + * connected as ALE and CLE inputs. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <nand.h> +#include <asm/io.h> + +/* + * Hardware specific access to control-lines + */ +static void nand_addr_hwcontrol(struct mtd_info *mtd, int cmd, uint ctrl) +{ + struct nand_chip *this = mtd->priv; + ulong IO_ADDR_W; + + if (ctrl & NAND_CTRL_CHANGE) { + IO_ADDR_W = (ulong)this->IO_ADDR_W; + + IO_ADDR_W &= ~(CONFIG_SYS_NAND_ACTL_CLE | + CONFIG_SYS_NAND_ACTL_ALE | + CONFIG_SYS_NAND_ACTL_NCE); + if (ctrl & NAND_CLE) + IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_CLE; + if (ctrl & NAND_ALE) + IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_ALE; + if (ctrl & NAND_NCE) + IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_NCE; + + this->IO_ADDR_W = (void *)IO_ADDR_W; + } + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); +} + +int board_nand_init(struct nand_chip *nand) +{ + nand->ecc.mode = NAND_ECC_SOFT; + nand->cmd_ctrl = nand_addr_hwcontrol; + nand->chip_delay = CONFIG_SYS_NAND_ACTL_DELAY; + + return 0; +} diff --git a/board/xes/common/fsl_8572_clk.c b/board/xes/common/fsl_8572_clk.c new file mode 100644 index 000000000..f5df2dae8 --- /dev/null +++ b/board/xes/common/fsl_8572_clk.c @@ -0,0 +1,51 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> + +/* + * Return SYSCLK input frequency - 50 MHz or 66 MHz depending on POR config + */ +unsigned long get_board_sys_clk(ulong dummy) +{ + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 gpporcr = gur->gpporcr; + + if (gpporcr & 0x10000) + return 66666666; + else + return 50000000; +} + +/* + * Return DDR input clock - synchronous with SYSCLK or 66 MHz + */ +unsigned long get_board_ddr_clk(ulong dummy) +{ + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 ddr_ratio = ((gur->porpllsr) & 0x00003e00) >> 9; + + if (ddr_ratio == 0x7) + return get_board_sys_clk(dummy); + + return 66666666; +} diff --git a/board/xes/common/fsl_85xx_ddr.c b/board/xes/common/fsl_85xx_ddr.c new file mode 100644 index 000000000..30b476701 --- /dev/null +++ b/board/xes/common/fsl_85xx_ddr.c @@ -0,0 +1,93 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/mmu.h> + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +extern void ddr_enable_ecc(unsigned int dram_size); +#endif + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + + dram_size *= 0x100000; + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* Initialize and enable DDR ECC */ + ddr_enable_ecc(dram_size); +#endif + + return dram_size; +} + +#if defined(CONFIG_DDR_ECC) || (CONFIG_NUM_DDR_CONTROLLERS > 1) +void board_add_ram_info(int use_default) +{ +#if (CONFIG_NUM_DDR_CONTROLLERS > 1) + volatile ccsr_ddr_t *ddr1 = (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR); +#endif + + puts(" ("); + +#if (CONFIG_NUM_DDR_CONTROLLERS > 1) + /* Print interleaving information */ + if (ddr1->cs0_config & 0x20000000) { + switch ((ddr1->cs0_config >> 24) & 0xf) { + case 0: + puts("cache line"); + break; + case 1: + puts("page"); + break; + case 2: + puts("bank"); + break; + case 3: + puts("super-bank"); + break; + default: + puts("invalid"); + break; + } + } else { + puts("no"); + } + + puts(" interleaving"); +#endif + +#if (CONFIG_NUM_DDR_CONTROLLERS > 1) && defined(CONFIG_DDR_ECC) + puts(", "); +#endif + +#if defined(CONFIG_DDR_ECC) + puts("ECC enabled"); +#endif + + puts(")"); +} +#endif /* CONFIG_DDR_ECC || CONFIG_NUM_DDR_CONTROLLERS > 1 */ diff --git a/board/xes/common/fsl_85xx_pci.c b/board/xes/common/fsl_85xx_pci.c new file mode 100644 index 000000000..9673a02b5 --- /dev/null +++ b/board/xes/common/fsl_85xx_pci.c @@ -0,0 +1,379 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <pci.h> +#include <asm/immap_85xx.h> +#include <asm/immap_fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> + +extern int fsl_pci_setup_inbound_windows(struct pci_region *r); +extern void fsl_pci_config_unlock(struct pci_controller *hose); +extern void fsl_pci_init(struct pci_controller *hose); + +int first_free_busno = 0; + +#ifdef CONFIG_PCI1 +static struct pci_controller pci1_hose; +#endif +#ifdef CONFIG_PCIE1 +static struct pci_controller pcie1_hose; +#endif +#ifdef CONFIG_PCIE2 +static struct pci_controller pcie2_hose; +#endif +#ifdef CONFIG_PCIE3 +static struct pci_controller pcie3_hose; +#endif + +#ifdef CONFIG_MPC8572 +/* Correlate host/agent POR bits to usable info. Table 4-14 */ +struct host_agent_cfg_t { + uchar pcie_root[3]; + uchar rio_host; +} host_agent_cfg[8] = { + {{0, 0, 0}, 0}, + {{0, 1, 1}, 1}, + {{1, 0, 1}, 0}, + {{1, 1, 0}, 1}, + {{0, 0, 1}, 0}, + {{0, 1, 0}, 1}, + {{1, 0, 0}, 0}, + {{1, 1, 1}, 1} +}; + +/* Correlate port width POR bits to usable info. Table 4-15 */ +struct io_port_cfg_t { + uchar pcie_width[3]; + uchar rio_width; +} io_port_cfg[16] = { + {{0, 0, 0}, 0}, + {{0, 0, 0}, 0}, + {{4, 0, 0}, 0}, + {{4, 4, 0}, 0}, + {{0, 0, 0}, 0}, + {{0, 0, 0}, 0}, + {{0, 0, 0}, 4}, + {{4, 2, 2}, 0}, + {{0, 0, 0}, 0}, + {{0, 0, 0}, 0}, + {{0, 0, 0}, 0}, + {{4, 0, 0}, 4}, + {{4, 0, 0}, 4}, + {{0, 0, 0}, 4}, + {{0, 0, 0}, 4}, + {{8, 0, 0}, 0}, +}; +#elif defined CONFIG_MPC8548 +/* Correlate host/agent POR bits to usable info. Table 4-12 */ +struct host_agent_cfg_t { + uchar pci_host[2]; + uchar pcie_root[1]; + uchar rio_host; +} host_agent_cfg[8] = { + {{1, 1}, {0}, 0}, + {{1, 1}, {1}, 0}, + {{1, 1}, {0}, 1}, + {{0, 0}, {0}, 0}, /* reserved */ + {{0, 1}, {1}, 0}, + {{1, 1}, {1}, 0}, + {{0, 1}, {1}, 1}, + {{1, 1}, {1}, 1} +}; + +/* Correlate port width POR bits to usable info. Table 4-13 */ +struct io_port_cfg_t { + uchar pcie_width[1]; + uchar rio_width; +} io_port_cfg[8] = { + {{0}, 0}, + {{0}, 0}, + {{0}, 0}, + {{4}, 4}, + {{4}, 4}, + {{0}, 4}, + {{0}, 4}, + {{8}, 0}, +}; +#endif + +void pci_init_board(void) +{ + struct pci_controller *hose; + volatile ccsr_fsl_pci_t *pci; + int width; + int host; + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + uint devdisr = gur->devdisr; + uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19; + uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16; + struct pci_region *r; + +#ifdef CONFIG_PCI1 + uint pci_spd_norm = (gur->pordevsr & MPC85xx_PORDEVSR_PCI1_SPD); + uint pci_32 = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_PCI32; + uint pci_arb = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; + uint pcix = gur->pordevsr & MPC85xx_PORDEVSR_PCI1; + uint freq = CONFIG_SYS_CLK_FREQ / 1000 / 1000; + + width = 0; /* Silence compiler warning... */ + io_sel &= 0xf; /* Silence compiler warning... */ + pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR; + hose = &pci1_hose; + host = host_agent_cfg[host_agent].pci_host[0]; + r = hose->regions; + + + if (!(devdisr & MPC85xx_DEVDISR_PCI1)) { + printf("\n PCI1: %d bit %s, %s %d MHz, %s, %s\n", + pci_32 ? 32 : 64, + pcix ? "PCIX" : "PCI", + pci_spd_norm ? ">=" : "<=", + pcix ? freq * 2 : freq, + host ? "host" : "agent", + pci_arb ? "arbiter" : "external-arbiter"); + + /* inbound */ + r += fsl_pci_setup_inbound_windows(r); + + /* outbound memory */ + pci_set_region(r++, + CONFIG_SYS_PCI1_MEM_BASE, + CONFIG_SYS_PCI1_MEM_PHYS, + CONFIG_SYS_PCI1_MEM_SIZE, + PCI_REGION_MEM); + + /* outbound io */ + pci_set_region(r++, + CONFIG_SYS_PCI1_IO_BASE, + CONFIG_SYS_PCI1_IO_PHYS, + CONFIG_SYS_PCI1_IO_SIZE, + PCI_REGION_IO); + + hose->region_count = r - hose->regions; + + hose->first_busno = first_free_busno; + pci_setup_indirect(hose, (int)&pci->cfg_addr, + (int)&pci->cfg_data); + + fsl_pci_init(hose); + + /* Unlock inbound PCI configuration cycles */ + if (!host) + fsl_pci_config_unlock(hose); + + first_free_busno = hose->last_busno + 1; + printf(" PCI1 on bus %02x - %02x\n", + hose->first_busno, hose->last_busno); + } else { + printf(" PCI1: disabled\n"); + } +#elif defined CONFIG_MPC8548 + /* PCI1 not present on MPC8572 */ + gur->devdisr |= MPC85xx_DEVDISR_PCI1; /* disable */ +#endif +#ifdef CONFIG_PCIE1 + pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR; + hose = &pcie1_hose; + host = host_agent_cfg[host_agent].pcie_root[0]; + width = io_port_cfg[io_sel].pcie_width[0]; + r = hose->regions; + + if (width && !(devdisr & MPC85xx_DEVDISR_PCIE)) { + printf("\n PCIE1 connected as %s (x%d)", + host ? "Root Complex" : "End Point", width); + if (pci->pme_msg_det) { + pci->pme_msg_det = 0xffffffff; + debug(" with errors. Clearing. Now 0x%08x", + pci->pme_msg_det); + } + printf("\n"); + + /* inbound */ + r += fsl_pci_setup_inbound_windows(r); + + /* outbound memory */ + pci_set_region(r++, + CONFIG_SYS_PCIE1_MEM_BASE, + CONFIG_SYS_PCIE1_MEM_PHYS, + CONFIG_SYS_PCIE1_MEM_SIZE, + PCI_REGION_MEM); + + /* outbound io */ + pci_set_region(r++, + CONFIG_SYS_PCIE1_IO_BASE, + CONFIG_SYS_PCIE1_IO_PHYS, + CONFIG_SYS_PCIE1_IO_SIZE, + PCI_REGION_IO); + + hose->region_count = r - hose->regions; + + hose->first_busno = first_free_busno; + pci_setup_indirect(hose, (int)&pci->cfg_addr, + (int) &pci->cfg_data); + + fsl_pci_init(hose); + + /* Unlock inbound PCI configuration cycles */ + if (!host) + fsl_pci_config_unlock(hose); + + first_free_busno = hose->last_busno + 1; + printf(" PCIE1 on bus %02x - %02x\n", + hose->first_busno, hose->last_busno); + } +#else + gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */ +#endif /* CONFIG_PCIE1 */ + +#ifdef CONFIG_PCIE2 + pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR; + hose = &pcie2_hose; + host = host_agent_cfg[host_agent].pcie_root[1]; + width = io_port_cfg[io_sel].pcie_width[1]; + r = hose->regions; + + if (width && !(devdisr & MPC85xx_DEVDISR_PCIE2)) { + printf("\n PCIE2 connected as %s (x%d)", + host ? "Root Complex" : "End Point", width); + if (pci->pme_msg_det) { + pci->pme_msg_det = 0xffffffff; + debug(" with errors. Clearing. Now 0x%08x", + pci->pme_msg_det); + } + printf("\n"); + + /* inbound */ + r += fsl_pci_setup_inbound_windows(r); + + /* outbound memory */ + pci_set_region(r++, + CONFIG_SYS_PCIE2_MEM_BASE, + CONFIG_SYS_PCIE2_MEM_PHYS, + CONFIG_SYS_PCIE2_MEM_SIZE, + PCI_REGION_MEM); + + /* outbound io */ + pci_set_region(r++, + CONFIG_SYS_PCIE2_IO_BASE, + CONFIG_SYS_PCIE2_IO_PHYS, + CONFIG_SYS_PCIE2_IO_SIZE, + PCI_REGION_IO); + + hose->region_count = r - hose->regions; + + hose->first_busno = first_free_busno; + pci_setup_indirect(hose, (int)&pci->cfg_addr, + (int)&pci->cfg_data); + + fsl_pci_init(hose); + + /* Unlock inbound PCI configuration cycles */ + if (!host) + fsl_pci_config_unlock(hose); + + first_free_busno = hose->last_busno + 1; + printf(" PCIE2 on bus %02x - %02x\n", + hose->first_busno, hose->last_busno); + } +#else + gur->devdisr |= MPC85xx_DEVDISR_PCIE2; /* disable */ +#endif /* CONFIG_PCIE2 */ + +#ifdef CONFIG_PCIE3 + pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE3_ADDR; + hose = &pcie3_hose; + host = host_agent_cfg[host_agent].pcie_root[2]; + width = io_port_cfg[io_sel].pcie_width[2]; + r = hose->regions; + + if (width && !(devdisr & MPC85xx_DEVDISR_PCIE3)) { + printf("\n PCIE3 connected as %s (x%d)", + host ? "Root Complex" : "End Point", width); + if (pci->pme_msg_det) { + pci->pme_msg_det = 0xffffffff; + debug(" with errors. Clearing. Now 0x%08x", + pci->pme_msg_det); + } + printf("\n"); + + /* inbound */ + r += fsl_pci_setup_inbound_windows(r); + + /* outbound memory */ + pci_set_region(r++, + CONFIG_SYS_PCIE3_MEM_BASE, + CONFIG_SYS_PCIE3_MEM_PHYS, + CONFIG_SYS_PCIE3_MEM_SIZE, + PCI_REGION_MEM); + + /* outbound io */ + pci_set_region(r++, + CONFIG_SYS_PCIE3_IO_BASE, + CONFIG_SYS_PCIE3_IO_PHYS, + CONFIG_SYS_PCIE3_IO_SIZE, + PCI_REGION_IO); + + hose->region_count = r - hose->regions; + + hose->first_busno = first_free_busno; + pci_setup_indirect(hose, (int)&pci->cfg_addr, + (int)&pci->cfg_data); + + fsl_pci_init(hose); + + /* Unlock inbound PCI configuration cycles */ + if (!host) + fsl_pci_config_unlock(hose); + + first_free_busno = hose->last_busno + 1; + printf(" PCIE3 on bus %02x - %02x\n", + hose->first_busno, hose->last_busno); + } +#else + gur->devdisr |= MPC85xx_DEVDISR_PCIE3; /* disable */ +#endif /* CONFIG_PCIE3 */ +} + +#if defined(CONFIG_OF_BOARD_SETUP) +extern void ft_fsl_pci_setup(void *blob, const char *pci_alias, + struct pci_controller *hose); + +void ft_board_pci_setup(void *blob, bd_t *bd) +{ + /* TODO - make node name (eg pci0) dynamic */ +#ifdef CONFIG_PCI1 + ft_fsl_pci_setup(blob, "pci0", &pci1_hose); +#endif +#ifdef CONFIG_PCIE1 + ft_fsl_pci_setup(blob, "pci2", &pcie1_hose); +#endif +#ifdef CONFIG_PCIE2 + ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); +#endif +#ifdef CONFIG_PCIE3 + ft_fsl_pci_setup(blob, "pci0", &pcie3_hose); +#endif +} +#endif /* CONFIG_OF_BOARD_SETUP */ diff --git a/board/xes/xpedite5200/Makefile b/board/xes/xpedite5200/Makefile new file mode 100644 index 000000000..02fe8fcd2 --- /dev/null +++ b/board/xes/xpedite5200/Makefile @@ -0,0 +1,55 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2004 Freescale Semiconductor. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS-y)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/xes/xpedite5200/config.mk b/board/xes/xpedite5200/config.mk new file mode 100644 index 000000000..be5a5c32c --- /dev/null +++ b/board/xes/xpedite5200/config.mk @@ -0,0 +1,34 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2004, 2007 Freescale Semiconductor. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# xpedite5200 board +# +ifndef TEXT_BASE +TEXT_BASE = 0xfff80000 +endif + +PLATFORM_CPPFLAGS += -DCONFIG_E500=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC8548=1 +PLATFORM_CPPFLAGS += -mrelocatable diff --git a/board/xes/xpedite5200/ddr.c b/board/xes/xpedite5200/ddr.c new file mode 100644 index 000000000..c5616d546 --- /dev/null +++ b/board/xes/xpedite5200/ddr.c @@ -0,0 +1,91 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <i2c.h> + +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> + +static void +get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address) +{ + i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t)); + + /* We use soldered memory, but use an SPD EEPROM to describe it. + * The SPD has an unspecified dimm type, but the DDR2 initialization + * code requires a specific type to be specified. This sets the type + * as a standard unregistered SO-DIMM. */ + if (spd->dimm_type == 0) { + spd->dimm_type = 0x4; + ((uchar *)spd)[63] += 0x4; + } +} + +unsigned int fsl_ddr_get_mem_data_rate(void) +{ + return get_ddr_freq(0); +} + +void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd, + unsigned int ctrl_num) +{ + unsigned int i; + + if (ctrl_num) { + printf("%s: invalid ctrl_num = %d\n", __func__, ctrl_num); + return; + } + + for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) + get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS); +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + /* + * Factors to consider for clock adjust: + * - number of chips on bus + * - position of slot + * - DDR1 vs. DDR2? + * - ??? + * + * This needs to be determined on a board-by-board basis. + * 0110 3/4 cycle late + * 0111 7/8 cycle late + */ + popts->clk_adjust = 7; + + /* + * Factors to consider for CPO: + * - frequency + * - ddr1 vs. ddr2 + */ + popts->cpo_override = 9; + + /* + * Factors to consider for write data delay: + * - number of DIMMs + * + * 1 = 1/4 clock delay + * 2 = 1/2 clock delay + * 3 = 3/4 clock delay + * 4 = 1 clock delay + * 5 = 5/4 clock delay + * 6 = 3/2 clock delay + */ + popts->write_data_delay = 3; + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; +} diff --git a/board/xes/xpedite5200/law.c b/board/xes/xpedite5200/law.c new file mode 100644 index 000000000..386f9c587 --- /dev/null +++ b/board/xes/xpedite5200/law.c @@ -0,0 +1,51 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +/* + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + /* LBC window - maps 256M 0xf0000000 -> 0xffffffff */ + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +#if CONFIG_SYS_PCI1_MEM_PHYS + SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_1G, LAW_TRGT_IF_PCI_1), + SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAWAR_SIZE_8M, LAW_TRGT_IF_PCI_1), +#endif +#if CONFIG_SYS_PCI2_MEM_PHYS + SET_LAW(CONFIG_SYS_PCI2_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCI_2), + SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCI_2), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/xes/xpedite5200/tlb.c b/board/xes/xpedite5200/tlb.c new file mode 100644 index 000000000..bd7bff820 --- /dev/null +++ b/board/xes/xpedite5200/tlb.c @@ -0,0 +1,85 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* W**G* - NOR flashes */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - NAND flash */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + +#if CONFIG_PCI1 + /* *I*G* - PCI MEM */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_PHYS, CONFIG_SYS_PCI1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), +#endif + +#if CONFIG_PCI2 + /* *I*G* - PCI MEM */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCI2_MEM_PHYS, CONFIG_SYS_PCI2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), +#endif + +#if defined(CONFIG_PCI1) || defined(CONFIG_PCI2) + /* *I*G* - PCI IO */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_IO_PHYS, CONFIG_SYS_PCI1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_16M, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/xes/xpedite5200/u-boot.lds b/board/xes/xpedite5200/u-boot.lds new file mode 100644 index 000000000..bd952d20f --- /dev/null +++ b/board/xes/xpedite5200/u-boot.lds @@ -0,0 +1,145 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2004, 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +PHDRS +{ + text PT_LOAD; + bss PT_LOAD; +} + +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + *(.text) + *(.got1) + } :text + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } :text + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + .bootpg ADDR(.text) + 0x7f000 : + { + cpu/mpc85xx/start.o (.bootpg) + } :text = 0xffff + + .resetvec ADDR(.text) + 0x7fffc : + { + *(.resetvec) + } :text = 0xffff + + . = ADDR(.text) + 0x80000; + + __bss_start = .; + .bss (NOLOAD) : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } :bss + + . = ALIGN(4); + _end = . ; + PROVIDE (end = .); +} diff --git a/board/xes/xpedite5200/xpedite5200.c b/board/xes/xpedite5200/xpedite5200.c new file mode 100644 index 000000000..e266d1dd8 --- /dev/null +++ b/board/xes/xpedite5200/xpedite5200.c @@ -0,0 +1,125 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2004, 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/processor.h> +#include <asm/immap_85xx.h> +#include <asm/immap_fsl_pci.h> +#include <asm/io.h> +#include <asm/cache.h> +#include <asm/mmu.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <pca953x.h> + +extern void ft_board_pci_setup(void *blob, bd_t *bd); + +int checkboard(void) +{ + volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); + volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR); + + char *s; + + printf("Board: X-ES %s PMC\n", CONFIG_SYS_BOARD_NAME); + printf(" "); + s = getenv("board_rev"); + if (s) + printf("Rev %s, ", s); + s = getenv("serial#"); + if (s) + printf("Serial# %s, ", s); + s = getenv("board_cfg"); + if (s) + printf("Cfg %s", s); + printf("\n"); + + lbc->ltesr = 0xffffffff; /* Clear LBC error interrupts */ + lbc->lteir = 0xffffffff; /* Enable LBC error interrupts */ + ecm->eedr = 0xffffffff; /* Clear ecm errors */ + ecm->eeer = 0xffffffff; /* Enable ecm errors */ + + return 0; +} + +static void flash_cs_fixup(void) +{ + volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_FLASH_PASS_CS)); + printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + lbc->br0 = CONFIG_SYS_BR1_PRELIM; + lbc->or0 = CONFIG_SYS_OR1_PRELIM; + + lbc->br1 = CONFIG_SYS_BR0_PRELIM; + lbc->or1 = CONFIG_SYS_OR0_PRELIM; + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + + /* + * Remap NOR flash region to caching-inhibited + * so that flash can be erased/programmed properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* Invalidate existing TLB entry for NOR flash */ + disable_tlb(0); + set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1); + + flash_cs_fixup(); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif diff --git a/board/xes/xpedite5370/Makefile b/board/xes/xpedite5370/Makefile new file mode 100644 index 000000000..919397c40 --- /dev/null +++ b/board/xes/xpedite5370/Makefile @@ -0,0 +1,45 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2007 Freescale Semiconductor, Inc. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS-y)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/xes/xpedite5370/config.mk b/board/xes/xpedite5370/config.mk new file mode 100644 index 000000000..39469b22c --- /dev/null +++ b/board/xes/xpedite5370/config.mk @@ -0,0 +1,35 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2007-2008 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# xpedite5370 board +# +ifndef TEXT_BASE +TEXT_BASE = 0xfff80000 +endif + +PLATFORM_RELFLAGS += -mrelocatable + +PLATFORM_CPPFLAGS += -DCONFIG_E500=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC8572=1 diff --git a/board/xes/xpedite5370/ddr.c b/board/xes/xpedite5370/ddr.c new file mode 100644 index 000000000..4d3f255d7 --- /dev/null +++ b/board/xes/xpedite5370/ddr.c @@ -0,0 +1,270 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <i2c.h> + +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> + +static void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address) +{ + i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, + sizeof(ddr2_spd_eeprom_t)); +} + +unsigned int fsl_ddr_get_mem_data_rate(void) +{ + return get_ddr_freq(0); +} + +void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd, + unsigned int ctrl_num) +{ + unsigned int i; + unsigned int i2c_address = 0; + + for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) { + if (ctrl_num == 0) + i2c_address = SPD_EEPROM_ADDRESS1; + if (ctrl_num == 1) + i2c_address = SPD_EEPROM_ADDRESS2; + get_spd(&(ctrl_dimms_spd[i]), i2c_address); + } +} + +/* + * There are four board-specific SDRAM timing parameters which must be + * calculated based on the particular PCB artwork. These are: + * 1.) CPO (Read Capture Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths and + * chip-specific internal delays. + * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths. + * Unless clock and DQ lanes are very different + * lengths (>2"), this should be set to the nominal value + * of 1/2 clock delay. + * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control) + * - DDR_SDRAM_CLK_CNTL register + * Source: Signal Integrity Simulations + * 4.) 2T Timing on Addr/Ctl + * - TIMING_CFG_2 register + * Source: Signal Integrity Simulations + * Usually only needed with heavy load/very high speed (>DDR2-800) + * + * ====== XPedite5370 DDR2-600 read delay calculations ====== + * + * See Freescale's App Note AN2583 as refrence. This document also + * contains the chip-specific delays for 8548E, 8572, etc. + * + * For MPC8572E + * Minimum chip delay (Ch 0): 1.372ns + * Maximum chip delay (Ch 0): 2.914ns + * Minimum chip delay (Ch 1): 1.220ns + * Maximum chip delay (Ch 1): 2.595ns + * + * CLK adjust = 5 (from simulations) = 5/8* 3.33ns = 2080ps + * + * Minimum delay calc (Ch 0): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 2.3" * 180 - 400ps + 1.9" * 180 + 2080ps + 1372ps + * = 3808ps + * = 3.808ns + * + * Maximum delay calc (Ch 0): + * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly + * 2.3" * 180 + 400ps + 2.4" * 180 + 2080ps + 2914ps + * = 6240ps + * = 6.240ns + * + * Minimum delay calc (Ch 1): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180- 400ps + 0.7" * 180 + 2080ps + 1220ps + * = 3288ps + * = 3.288ns + * + * Maximum delay calc (Ch 1): + * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180+ 400ps + 1.1" * 180 + 2080ps + 2595ps + * = 5536ps + * = 5.536ns + * + * Ch.0: 3.808ns to 6.240ns additional delay needed (pick 5ns as target) + * This is 1.5 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) + * Ch.1: 3.288ns to 5.536ns additional delay needed (pick 4.4ns as target) + * This is 1.32 clock cycles, pick CPO = READ_LAT + 5/4 (0x7) + * + * + * ====== XPedite5370 DDR2-800 read delay calculations ====== + * + * See Freescale's App Note AN2583 as refrence. This document also + * contains the chip-specific delays for 8548E, 8572, etc. + * + * For MPC8572E + * Minimum chip delay (Ch 0): 1.372ns + * Maximum chip delay (Ch 0): 2.914ns + * Minimum chip delay (Ch 1): 1.220ns + * Maximum chip delay (Ch 1): 2.595ns + * + * CLK adjust = 5 (from simulations) = 5/8* 2.5ns = 1563ps + * + * Minimum delay calc (Ch 0): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 2.3" * 180 - 350ps + 1.9" * 180 + 1563ps + 1372ps + * = 3341ps + * = 3.341ns + * + * Maximum delay calc (Ch 0): + * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly + * 2.3" * 180 + 350ps + 2.4" * 180 + 1563ps + 2914ps + * = 5673ps + * = 5.673ns + * + * Minimum delay calc (Ch 1): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180- 350ps + 0.7" * 180 + 1563ps + 1220ps + * = 2822ps + * = 2.822ns + * + * Maximum delay calc (Ch 1): + * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180+ 350ps + 1.1" * 180 + 1563ps + 2595ps + * = 4968ps + * = 4.968ns + * + * Ch.0: 3.341ns to 5.673ns additional delay needed (pick 4.5ns as target) + * This is 1.8 clock cycles, pick CPO = READ_LAT + 7/4 (0x9) + * Ch.1: 2.822ns to 4.968ns additional delay needed (pick 3.9ns as target) + * This is 1.56 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) + * + * Write latency (WR_DATA_DELAY) is calculated by doing the following: + * + * The DDR SDRAM specification requires DQS be received no sooner than + * 75% of an SDRAM clock period—and no later than 125% of a clock + * period—from the capturing clock edge of the command/address at the + * SDRAM. + * + * Based on the above tracelengths, the following are calculated: + * Ch. 0 8572 to DRAM propagation (DQ lanes) : 1.9" * 180 = 0.342ns + * Ch. 0 8572 to DRAM propagation (CLKs) : 2.3" * 180 = 0.414ns + * Ch. 1 8572 to DRAM propagation (DQ lanes) : 0.7" * 180 = 0.126ns + * Ch. 1 8572 to DRAM propagation (CLKs ) : 1.47" * 180 = 0.264ns + * + * Difference in arrival time CLK vs. DQS: + * Ch. 0 0.072ns + * Ch. 1 0.138ns + * + * Both of these values are much less than 25% of the clock + * period at DDR2-600 or DDR2-800, so no additional delay is needed over + * the 1/2 cycle which normally aligns the first DQS transition + * exactly WL (CAS latency minus one cycle) after the CAS strobe. + * See Figure 9-53 in MPC8572E manual: "1/2 delay" in Freescale's + * terminology corresponds to exactly one clock period delay after + * the CAS strobe. (due to the fact that the "delay" is referenced + * from the *falling* edge of the CLK, just after the rising edge + * which the CAS strobe is latched on. + */ + +typedef struct board_memctl_options { + uint16_t datarate_mhz_low; + uint16_t datarate_mhz_high; + uint8_t clk_adjust; + uint8_t cpo_override; + uint8_t write_data_delay; +} board_memctl_options_t; + +static struct board_memctl_options bopts_ctrl[][2] = { + { + /* Controller 0 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 9, + .write_data_delay = 2, + }, + }, + { + /* Controller 1 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 7, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + }, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + struct board_memctl_options *bopts = bopts_ctrl[ctrl_num]; + sys_info_t sysinfo; + int i; + unsigned int datarate; + + get_sys_info(&sysinfo); + datarate = sysinfo.freqDDRBus / 1000 / 1000; + + for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) { + if ((bopts[i].datarate_mhz_low <= datarate) && + (bopts[i].datarate_mhz_high >= datarate)) { + debug("controller %d:\n", ctrl_num); + debug(" clk_adjust = %d\n", bopts[i].clk_adjust); + debug(" cpo = %d\n", bopts[i].cpo_override); + debug(" write_data_delay = %d\n", + bopts[i].write_data_delay); + popts->clk_adjust = bopts[i].clk_adjust; + popts->cpo_override = bopts[i].cpo_override; + popts->write_data_delay = bopts[i].write_data_delay; + } + } + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; +} diff --git a/board/xes/xpedite5370/law.c b/board/xes/xpedite5370/law.c new file mode 100644 index 000000000..daee676c4 --- /dev/null +++ b/board/xes/xpedite5370/law.c @@ -0,0 +1,54 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +/* + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +#ifdef CONFIG_SYS_PCIE1_MEM_PHYS + SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_1G, LAW_TRGT_IF_PCIE_1), + SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_1), +#endif +#ifdef CONFIG_SYS_PCIE2_MEM_PHYS + SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_2), + SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_2), +#endif +#ifdef CONFIG_SYS_PCIE3_MEM_PHYS + SET_LAW(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_3), + SET_LAW(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_3), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/xes/xpedite5370/tlb.c b/board/xes/xpedite5370/tlb.c new file mode 100644 index 000000000..caafa3011 --- /dev/null +++ b/board/xes/xpedite5370/tlb.c @@ -0,0 +1,94 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* W**G* - NOR flashes */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - NAND flash */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + +#ifdef CONFIG_PCIE1 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), +#endif + +#ifdef CONFIG_PCIE2 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), +#endif + +#ifdef CONFIG_PCIE3 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), +#endif + +#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_64M, 1), +#endif + +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/xes/xpedite5370/u-boot.lds b/board/xes/xpedite5370/u-boot.lds new file mode 100644 index 000000000..cb399120d --- /dev/null +++ b/board/xes/xpedite5370/u-boot.lds @@ -0,0 +1,145 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +PHDRS +{ + text PT_LOAD; + bss PT_LOAD; +} + +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + *(.text) + *(.got1) + } :text + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } :text + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + .bootpg ADDR(.text) + 0x7f000 : + { + cpu/mpc85xx/start.o (.bootpg) + } :text = 0xffff + + .resetvec ADDR(.text) + 0x7fffc : + { + *(.resetvec) + } :text = 0xffff + + . = ADDR(.text) + 0x80000; + + __bss_start = .; + .bss (NOLOAD) : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } :bss + + . = ALIGN(4); + _end = . ; + PROVIDE (end = .); +} diff --git a/board/xes/xpedite5370/xpedite5370.c b/board/xes/xpedite5370/xpedite5370.c new file mode 100644 index 000000000..487509527 --- /dev/null +++ b/board/xes/xpedite5370/xpedite5370.c @@ -0,0 +1,128 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/immap_fsl_pci.h> +#include <asm/io.h> +#include <asm/cache.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <pca953x.h> + +DECLARE_GLOBAL_DATA_PTR; + +extern void ft_board_pci_setup(void *blob, bd_t *bd); + +int checkboard(void) +{ + char *s; + + printf("Board: X-ES %s 3U VPX SBC\n", CONFIG_SYS_BOARD_NAME); + printf(" "); + s = getenv("board_rev"); + if (s) + printf("Rev %s, ", s); + s = getenv("serial#"); + if (s) + printf("Serial# %s, ", s); + s = getenv("board_cfg"); + if (s) + printf("Cfg %s", s); + printf("\n"); + + return 0; +} + +static void flash_cs_fixup(void) +{ + volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS)); + printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + lbc->br0 = CONFIG_SYS_BR1_PRELIM; + lbc->or0 = CONFIG_SYS_OR1_PRELIM; + + lbc->br1 = CONFIG_SYS_BR0_PRELIM; + lbc->or1 = CONFIG_SYS_OR0_PRELIM; + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + + /* + * Remap NOR flash region to caching-inhibited + * so that flash can be erased/programmed properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* Invalidate existing TLB entry for NOR flash */ + disable_tlb(0); + set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1); + + flash_cs_fixup(); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif + +#ifdef CONFIG_MP +extern void cpu_mp_lmb_reserve(struct lmb *lmb); + +void board_lmb_reserve(struct lmb *lmb) +{ + cpu_mp_lmb_reserve(lmb); +} +#endif diff --git a/cpu/mpc85xx/cpu.c b/cpu/mpc85xx/cpu.c index 943602f92..15ba7f1c5 100644 --- a/cpu/mpc85xx/cpu.c +++ b/cpu/mpc85xx/cpu.c @@ -77,8 +77,6 @@ struct cpu_type *identify_cpu(u32 ver) int checkcpu (void) { sys_info_t sysinfo; - uint lcrr; /* local bus clock ratio register */ - uint clkdiv; /* clock divider portion of lcrr */ uint pvr, svr; uint fam; uint ver; @@ -165,30 +163,11 @@ int checkcpu (void) break; } -#if defined(CONFIG_SYS_LBC_LCRR) - lcrr = CONFIG_SYS_LBC_LCRR; -#else - { - volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); - - lcrr = lbc->lcrr; - } -#endif - clkdiv = lcrr & 0x0f; - if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) { -#if defined(CONFIG_MPC8548) || defined(CONFIG_MPC8544) || \ - defined(CONFIG_MPC8572) || defined(CONFIG_MPC8536) - /* - * Yes, the entire PQ38 family use the same - * bit-representation for twice the clock divider values. - */ - clkdiv *= 2; -#endif - printf("LBC:%-4s MHz\n", - strmhz(buf1, sysinfo.freqSystemBus / clkdiv)); - } else { - printf("LBC: unknown (lcrr: 0x%08x)\n", lcrr); - } + if (sysinfo.freqLocalBus > LCRR_CLKDIV) + printf("LBC:%-4s MHz\n", strmhz(buf1, sysinfo.freqLocalBus)); + else + printf("LBC: unknown (LCRR[CLKDIV] = 0x%02lx)\n", + sysinfo.freqLocalBus); #ifdef CONFIG_CPM2 printf("CPM: %s MHz\n", strmhz(buf1, sysinfo.freqSystemBus)); diff --git a/cpu/mpc85xx/fdt.c b/cpu/mpc85xx/fdt.c index 59aafb1be..69fab9952 100644 --- a/cpu/mpc85xx/fdt.c +++ b/cpu/mpc85xx/fdt.c @@ -28,11 +28,12 @@ #include <fdt_support.h> #include <asm/processor.h> +DECLARE_GLOBAL_DATA_PTR; + extern void ft_qe_setup(void *blob); #ifdef CONFIG_MP #include "mp.h" -DECLARE_GLOBAL_DATA_PTR; void ft_fixup_cpu(void *blob, u64 memory_limit) { @@ -231,6 +232,11 @@ void ft_cpu_setup(void *blob, bd_t *bd) "clock-frequency", bd->bi_intfreq, 1); do_fixup_by_prop_u32(blob, "device_type", "soc", 4, "bus-frequency", bd->bi_busfreq, 1); + + do_fixup_by_compat_u32(blob, "fsl,pq3-localbus", + "bus-frequency", gd->lbc_clk, 1); + do_fixup_by_compat_u32(blob, "fsl,elbc", + "bus-frequency", gd->lbc_clk, 1); #ifdef CONFIG_QE ft_qe_setup(blob); #endif diff --git a/cpu/mpc85xx/release.S b/cpu/mpc85xx/release.S index 7c3e8a172..54c936c3e 100644 --- a/cpu/mpc85xx/release.S +++ b/cpu/mpc85xx/release.S @@ -157,6 +157,7 @@ __secondary_start_page: mfspr r0,SPRN_PIR stw r0,ENTRY_PIR(r10) + mtspr IVPR,r12 /* * Coming here, we know the cpu has one TLB mapping in TLB1[0] * which maps 0xfffff000-0xffffffff one-to-one. We set up a diff --git a/cpu/mpc85xx/speed.c b/cpu/mpc85xx/speed.c index 1e0f4838b..0d55228b6 100644 --- a/cpu/mpc85xx/speed.c +++ b/cpu/mpc85xx/speed.c @@ -28,6 +28,7 @@ #include <common.h> #include <ppc_asm.tmpl> #include <asm/processor.h> +#include <asm/io.h> DECLARE_GLOBAL_DATA_PTR; @@ -37,6 +38,7 @@ void get_sys_info (sys_info_t * sysInfo) { volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); uint plat_ratio,e500_ratio,half_freqSystemBus; + uint lcrr_div; plat_ratio = (gur->porpllsr) & 0x0000003e; plat_ratio >>= 1; @@ -60,6 +62,30 @@ void get_sys_info (sys_info_t * sysInfo) sysInfo->freqDDRBus = ddr_ratio * CONFIG_DDR_CLK_FREQ; } #endif + +#if defined(CONFIG_SYS_LBC_LCRR) + /* We will program LCRR to this value later */ + lcrr_div = CONFIG_SYS_LBC_LCRR & LCRR_CLKDIV; +#else + { + volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); + lcrr_div = in_be32(&lbc->lcrr) & LCRR_CLKDIV; + } +#endif + if (lcrr_div == 2 || lcrr_div == 4 || lcrr_div == 8) { +#if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8541) && \ + !defined(CONFIG_MPC8555) && !defined(CONFIG_MPC8560) + /* + * Yes, the entire PQ38 family use the same + * bit-representation for twice the clock divider values. + */ + lcrr_div *= 2; +#endif + sysInfo->freqLocalBus = sysInfo->freqSystemBus / lcrr_div; + } else { + /* In case anyone cares what the unknown value is */ + sysInfo->freqLocalBus = lcrr_div; + } } @@ -82,6 +108,7 @@ int get_clocks (void) gd->cpu_clk = sys_info.freqProcessor; gd->bus_clk = sys_info.freqSystemBus; gd->mem_clk = sys_info.freqDDRBus; + gd->lbc_clk = sys_info.freqLocalBus; /* * The base clock for I2C depends on the actual SOC. Unfortunately, diff --git a/cpu/mpc85xx/start.S b/cpu/mpc85xx/start.S index 8fa0ff7a8..80f96773e 100644 --- a/cpu/mpc85xx/start.S +++ b/cpu/mpc85xx/start.S @@ -184,19 +184,19 @@ _start_e500: mtspr DBCR0,r0 #endif - /* create a temp mapping in AS=1 to the boot window */ + /* create a temp mapping in AS=1 to the 4M boot window */ lis r6,FSL_BOOKE_MAS0(1, 15, 0)@h ori r6,r6,FSL_BOOKE_MAS0(1, 15, 0)@l - lis r7,FSL_BOOKE_MAS1(1, 1, 0, 1, BOOKE_PAGESZ_16M)@h - ori r7,r7,FSL_BOOKE_MAS1(1, 1, 0, 1, BOOKE_PAGESZ_16M)@l + lis r7,FSL_BOOKE_MAS1(1, 1, 0, 1, BOOKE_PAGESZ_4M)@h + ori r7,r7,FSL_BOOKE_MAS1(1, 1, 0, 1, BOOKE_PAGESZ_4M)@l - /* Align the mapping to 16MB */ - lis r8,FSL_BOOKE_MAS2(TEXT_BASE & 0xff000000, (MAS2_I|MAS2_G))@h - ori r8,r8,FSL_BOOKE_MAS2(TEXT_BASE & 0xff000000, (MAS2_I|MAS2_G))@l + lis r8,FSL_BOOKE_MAS2(TEXT_BASE & 0xffc00000, (MAS2_I|MAS2_G))@h + ori r8,r8,FSL_BOOKE_MAS2(TEXT_BASE & 0xffc00000, (MAS2_I|MAS2_G))@l - lis r9,FSL_BOOKE_MAS3(0xff000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR))@h - ori r9,r9,FSL_BOOKE_MAS3(0xff000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR))@l + /* The 85xx has the default boot window 0xff800000 - 0xffffffff */ + lis r9,FSL_BOOKE_MAS3(0xffc00000, 0, (MAS3_SX|MAS3_SW|MAS3_SR))@h + ori r9,r9,FSL_BOOKE_MAS3(0xffc00000, 0, (MAS3_SX|MAS3_SW|MAS3_SR))@l mtspr MAS0,r6 mtspr MAS1,r7 diff --git a/cpu/mpc85xx/tlb.c b/cpu/mpc85xx/tlb.c index a2d16ae2f..5b5f7914f 100644 --- a/cpu/mpc85xx/tlb.c +++ b/cpu/mpc85xx/tlb.c @@ -26,6 +26,11 @@ #include <common.h> #include <asm/processor.h> #include <asm/mmu.h> +#ifdef CONFIG_ADDR_MAP +#include <addr_map.h> +#endif + +DECLARE_GLOBAL_DATA_PTR; void set_tlb(u8 tlb, u32 epn, u64 rpn, u8 perms, u8 wimge, @@ -47,6 +52,11 @@ void set_tlb(u8 tlb, u32 epn, u64 rpn, mtspr(MAS7, _mas7); #endif asm volatile("isync;msync;tlbwe;isync"); + +#ifdef CONFIG_ADDR_MAP + if ((tlb == 1) && (gd->flags & GD_FLG_RELOC)) + addrmap_set_entry(epn, rpn, (1UL << ((tsize * 2) + 10)), esel); +#endif } void disable_tlb(u8 esel) @@ -67,6 +77,11 @@ void disable_tlb(u8 esel) mtspr(MAS7, _mas7); #endif asm volatile("isync;msync;tlbwe;isync"); + +#ifdef CONFIG_ADDR_MAP + if (gd->flags & GD_FLG_RELOC) + addrmap_set_entry(0, 0, 0, esel); +#endif } void invalidate_tlb(u8 tlb) @@ -91,6 +106,25 @@ void init_tlbs(void) return ; } +#ifdef CONFIG_ADDR_MAP +void init_addr_map(void) +{ + int i; + + for (i = 0; i < num_tlb_entries; i++) { + if (tlb_table[i].tlb == 0) + continue; + + addrmap_set_entry(tlb_table[i].epn, + tlb_table[i].rpn, + (1UL << ((tlb_table[i].tsize * 2) + 10)), + tlb_table[i].esel); + } + + return ; +} +#endif + unsigned int setup_ddr_tlbs(unsigned int memsize_in_meg) { unsigned int tlb_size; diff --git a/cpu/mpc86xx/cpu.c b/cpu/mpc86xx/cpu.c index 4cace984d..35680238d 100644 --- a/cpu/mpc86xx/cpu.c +++ b/cpu/mpc86xx/cpu.c @@ -39,8 +39,6 @@ checkcpu(void) uint pvr, svr; uint ver; uint major, minor; - uint lcrr; /* local bus clock ratio register */ - uint clkdiv; /* clock divider portion of lcrr */ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; volatile ccsr_gur_t *gur = &immap->im_gur; @@ -100,22 +98,11 @@ checkcpu(void) printf("MPX:%4lu MHz, ", sysinfo.freqSystemBus / 1000000); printf("DDR:%4lu MHz, ", sysinfo.freqSystemBus / 2000000); -#if defined(CONFIG_SYS_LBC_LCRR) - lcrr = CONFIG_SYS_LBC_LCRR; -#else - { - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile ccsr_lbc_t *lbc = &immap->im_lbc; - - lcrr = lbc->lcrr; - } -#endif - clkdiv = lcrr & 0x0f; - if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) { - printf("LBC:%4lu MHz\n", - sysinfo.freqSystemBus / 1000000 / clkdiv); + if (sysinfo.freqLocalBus > LCRR_CLKDIV) { + printf("LBC:%4lu MHz\n", sysinfo.freqLocalBus / 1000000); } else { - printf(" LBC: unknown (lcrr: 0x%08x)\n", lcrr); + printf("LBC: unknown (LCRR[CLKDIV] = 0x%02x)\n", + sysinfo.freqLocalBus); } puts(" L2: "); diff --git a/cpu/mpc86xx/fdt.c b/cpu/mpc86xx/fdt.c index 3adfad98c..e277040bb 100644 --- a/cpu/mpc86xx/fdt.c +++ b/cpu/mpc86xx/fdt.c @@ -13,6 +13,8 @@ DECLARE_GLOBAL_DATA_PTR; +DECLARE_GLOBAL_DATA_PTR; + void ft_cpu_setup(void *blob, bd_t *bd) { #if (CONFIG_NUM_CPUS > 1) @@ -29,6 +31,13 @@ void ft_cpu_setup(void *blob, bd_t *bd) do_fixup_by_prop_u32(blob, "device_type", "soc", 4, "bus-frequency", bd->bi_busfreq, 1); +#if defined(CONFIG_MPC8641) + do_fixup_by_compat_u32(blob, "fsl,mpc8641-localbus", + "bus-frequency", gd->lbc_clk, 1); +#endif + do_fixup_by_compat_u32(blob, "fsl,elbc", + "bus-frequency", gd->lbc_clk, 1); + fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); #if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) \ diff --git a/cpu/mpc86xx/speed.c b/cpu/mpc86xx/speed.c index 415ac9db8..64a3479d7 100644 --- a/cpu/mpc86xx/speed.c +++ b/cpu/mpc86xx/speed.c @@ -28,6 +28,7 @@ #include <common.h> #include <mpc86xx.h> #include <asm/processor.h> +#include <asm/io.h> DECLARE_GLOBAL_DATA_PTR; @@ -39,6 +40,7 @@ void get_sys_info(sys_info_t *sysInfo) volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; volatile ccsr_gur_t *gur = &immap->im_gur; uint plat_ratio, e600_ratio; + uint lcrr_div; plat_ratio = (gur->porpllsr) & 0x0000003e; plat_ratio >>= 1; @@ -90,6 +92,22 @@ void get_sys_info(sys_info_t *sysInfo) sysInfo->freqProcessor = e600_ratio + sysInfo->freqSystemBus; break; } + +#if defined(CONFIG_SYS_LBC_LCRR) + /* We will program LCRR to this value later */ + lcrr_div = CONFIG_SYS_LBC_LCRR & LCRR_CLKDIV; +#else + { + volatile ccsr_lbc_t *lbc = &immap->im_lbc; + lcrr_div = in_be32(&lbc->lcrr) & LCRR_CLKDIV; + } +#endif + if (lcrr_div == 2 || lcrr_div == 4 || lcrr_div == 8) { + sysInfo->freqLocalBus = sysInfo->freqSystemBus / (lcrr_div * 2); + } else { + /* In case anyone cares what the unknown value is */ + sysInfo->freqLocalBus = lcrr_div; + } } @@ -105,6 +123,7 @@ int get_clocks(void) get_sys_info(&sys_info); gd->cpu_clk = sys_info.freqProcessor; gd->bus_clk = sys_info.freqSystemBus; + gd->lbc_clk = sys_info.freqLocalBus; /* * The base clock for I2C depends on the actual SOC. Unfortunately, diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile new file mode 100644 index 000000000..dd618ed71 --- /dev/null +++ b/drivers/gpio/Makefile @@ -0,0 +1,47 @@ +# +# Copyright 2000-2008 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB := $(obj)libgpio.a + +COBJS-$(CONFIG_PCA953X) += pca953x.o + +COBJS := $(COBJS-y) +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +all: $(LIB) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################## diff --git a/drivers/gpio/pca953x.c b/drivers/gpio/pca953x.c new file mode 100644 index 000000000..390d99ad3 --- /dev/null +++ b/drivers/gpio/pca953x.c @@ -0,0 +1,227 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Driver for NXP's 4 and 8 bit I2C gpio expanders (eg pca9537, pca9557, etc) + * TODO: support additional devices with more than 8-bits GPIO + */ + +#include <common.h> +#include <i2c.h> +#include <pca953x.h> + +/* Default to an address that hopefully won't corrupt other i2c devices */ +#ifndef CONFIG_SYS_I2C_PCA953X_ADDR +#define CONFIG_SYS_I2C_PCA953X_ADDR (~0) +#endif + +enum { + PCA953X_CMD_INFO, + PCA953X_CMD_DEVICE, + PCA953X_CMD_OUTPUT, + PCA953X_CMD_INPUT, + PCA953X_CMD_INVERT, +}; + +/* + * Modify masked bits in register + */ +static int pca953x_reg_write(uint8_t chip, uint addr, uint mask, uint data) +{ + uint8_t val; + + if (i2c_read(chip, addr, 1, &val, 1)) + return -1; + + val &= ~mask; + val |= data; + + return i2c_write(chip, addr, 1, &val, 1); +} + +/* + * Set output value of IO pins in 'mask' to corresponding value in 'data' + * 0 = low, 1 = high + */ +int pca953x_set_val(uint8_t chip, uint mask, uint data) +{ + return pca953x_reg_write(chip, PCA953X_OUT, mask, data); +} + +/* + * Set read polarity of IO pins in 'mask' to corresponding value in 'data' + * 0 = read pin value, 1 = read inverted pin value + */ +int pca953x_set_pol(uint8_t chip, uint mask, uint data) +{ + return pca953x_reg_write(chip, PCA953X_POL, mask, data); +} + +/* + * Set direction of IO pins in 'mask' to corresponding value in 'data' + * 0 = output, 1 = input + */ +int pca953x_set_dir(uint8_t chip, uint mask, uint data) +{ + return pca953x_reg_write(chip, PCA953X_CONF, mask, data); +} + +/* + * Read current logic level of all IO pins + */ +int pca953x_get_val(uint8_t chip) +{ + uint8_t val; + + if (i2c_read(chip, 0, 1, &val, 1)) + return -1; + + return (int)val; +} + +#ifdef CONFIG_CMD_PCA953X +#ifdef CONFIG_CMD_PCA953X_INFO +/* + * Display pca953x information + */ +static int pca953x_info(uint8_t chip) +{ + int i; + uint8_t data; + + printf("pca953x@ 0x%x:\n\n", chip); + printf("gpio pins: 76543210\n"); + printf("-------------------\n"); + + if (i2c_read(chip, PCA953X_CONF, 1, &data, 1)) + return -1; + printf("conf: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? 'i' : 'o'); + printf("\n"); + + if (i2c_read(chip, PCA953X_POL, 1, &data, 1)) + return -1; + printf("invert: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? '1' : '0'); + printf("\n"); + + if (i2c_read(chip, PCA953X_IN, 1, &data, 1)) + return -1; + printf("input: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? '1' : '0'); + printf("\n"); + + if (i2c_read(chip, PCA953X_OUT, 1, &data, 1)) + return -1; + printf("output: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? '1' : '0'); + printf("\n"); + + return 0; +} +#endif /* CONFIG_CMD_PCA953X_INFO */ + +cmd_tbl_t cmd_pca953x[] = { + U_BOOT_CMD_MKENT(device, 3, 0, (void *)PCA953X_CMD_DEVICE, "", ""), + U_BOOT_CMD_MKENT(output, 4, 0, (void *)PCA953X_CMD_OUTPUT, "", ""), + U_BOOT_CMD_MKENT(input, 3, 0, (void *)PCA953X_CMD_INPUT, "", ""), + U_BOOT_CMD_MKENT(invert, 4, 0, (void *)PCA953X_CMD_INVERT, "", ""), +#ifdef CONFIG_CMD_PCA953X_INFO + U_BOOT_CMD_MKENT(info, 2, 0, (void *)PCA953X_CMD_INFO, "", ""), +#endif +}; + +int do_pca953x(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + static uint8_t chip = CONFIG_SYS_I2C_PCA953X_ADDR; + int val; + ulong ul_arg2 = 0; + ulong ul_arg3 = 0; + cmd_tbl_t *c; + + c = find_cmd_tbl(argv[1], cmd_pca953x, ARRAY_SIZE(cmd_pca953x)); + + /* All commands but "device" require 'maxargs' arguments */ + if (!c || !((argc == (c->maxargs)) || + (((int)c->cmd == PCA953X_CMD_DEVICE) && + (argc == (c->maxargs - 1))))) { + printf("Usage:\n%s\n", cmdtp->usage); + return 1; + } + + /* arg2 used as chip number or pin number */ + if (argc > 2) + ul_arg2 = simple_strtoul(argv[2], NULL, 16); + + /* arg3 used as pin or invert value */ + if (argc > 3) + ul_arg3 = simple_strtoul(argv[3], NULL, 16) & 0x1; + + switch ((int)c->cmd) { +#ifdef CONFIG_CMD_PCA953X_INFO + case PCA953X_CMD_INFO: + return pca953x_info(chip); +#endif + case PCA953X_CMD_DEVICE: + if (argc == 3) + chip = (uint8_t)ul_arg2; + printf("Current device address: 0x%x\n", chip); + return 0; + case PCA953X_CMD_INPUT: + pca953x_set_dir(chip, (1 << ul_arg2), + PCA953X_DIR_IN << ul_arg2); + val = (pca953x_get_val(chip) & (1 << ul_arg2)) != 0; + + printf("chip 0x%02x, pin 0x%lx = %d\n", chip, ul_arg2, val); + return val; + case PCA953X_CMD_OUTPUT: + pca953x_set_dir(chip, (1 << ul_arg2), + (PCA953X_DIR_OUT << ul_arg2)); + return pca953x_set_val(chip, (1 << ul_arg2), + (ul_arg3 << ul_arg2)); + case PCA953X_CMD_INVERT: + return pca953x_set_pol(chip, (1 << ul_arg2), + (ul_arg3 << ul_arg2)); + default: + /* We should never get here */ + return 1; + } +} + +U_BOOT_CMD( + pca953x, 5, 1, do_pca953x, + "pca953x - pca953x gpio access\n", + "device [dev]\n" + " - show or set current device address\n" +#ifdef CONFIG_CMD_PCA953X_INFO + "pca953x info\n" + " - display info for current chip\n" +#endif + "pca953x output pin 0|1\n" + " - set pin as output and drive low or high\n" + "pca953x invert pin 0|1\n" + " - disable/enable polarity inversion for reads\n" + "pca953x intput pin\n" + " - set pin as input and read value\n" +); + +#endif /* CONFIG_CMD_PCA953X */ diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c index 367c7d7fc..3f318e02e 100644 --- a/drivers/mtd/nand/fsl_elbc_nand.c +++ b/drivers/mtd/nand/fsl_elbc_nand.c @@ -718,7 +718,7 @@ static void fsl_elbc_ctrl_init(void) int board_nand_init(struct nand_chip *nand) { struct fsl_elbc_mtd *priv; - uint32_t br, or; + uint32_t br = 0, or = 0; if (!elbc_ctrl) { fsl_elbc_ctrl_init(); @@ -737,11 +737,13 @@ int board_nand_init(struct nand_chip *nand) * if we could pass more than one datum to the NAND driver... */ for (priv->bank = 0; priv->bank < MAX_BANKS; priv->bank++) { + phys_addr_t base_addr = virt_to_phys(nand->IO_ADDR_R); + br = in_be32(&elbc_ctrl->regs->bank[priv->bank].br); or = in_be32(&elbc_ctrl->regs->bank[priv->bank].or); if ((br & BR_V) && (br & BR_MSEL) == BR_MS_FCM && - (br & or & BR_BA) == (phys_addr_t)nand->IO_ADDR_R) + (br & or & BR_BA) == BR_PHYS_ADDR(base_addr)) break; } diff --git a/drivers/pci/fsl_pci_init.c b/drivers/pci/fsl_pci_init.c index 1db42fd8d..db68f2600 100644 --- a/drivers/pci/fsl_pci_init.c +++ b/drivers/pci/fsl_pci_init.c @@ -37,6 +37,11 @@ DECLARE_GLOBAL_DATA_PTR; #include <pci.h> #include <asm/immap_fsl_pci.h> +/* Freescale-specific PCI config registers */ +#define FSL_PCI_PBFR 0x44 +#define FSL_PCIE_CAP_ID 0x4c +#define FSL_PCIE_CFG_RDY 0x4b0 + void pciauto_prescan_setup_bridge(struct pci_controller *hose, pci_dev_t dev, int sub_bus); void pciauto_postscan_setup_bridge(struct pci_controller *hose, @@ -306,6 +311,30 @@ void fsl_pci_init(struct pci_controller *hose) } } +/* Enable inbound PCI config cycles for agent/endpoint interface */ +void fsl_pci_config_unlock(struct pci_controller *hose) +{ + pci_dev_t dev = PCI_BDF(hose->first_busno,0,0); + u8 agent; + u8 pcie_cap; + u16 pbfr; + + pci_hose_read_config_byte(hose, dev, PCI_CLASS_PROG, &agent); + if (!agent) + return; + + pci_hose_read_config_byte(hose, dev, FSL_PCIE_CAP_ID, &pcie_cap); + if (pcie_cap != 0x0) { + /* PCIe - set CFG_READY bit of Configuration Ready Register */ + pci_hose_write_config_byte(hose, dev, FSL_PCIE_CFG_RDY, 0x1); + } else { + /* PCI - clear ACL bit of PBFR */ + pci_hose_read_config_word(hose, dev, FSL_PCI_PBFR, &pbfr); + pbfr &= ~0x20; + pci_hose_write_config_word(hose, dev, FSL_PCI_PBFR, pbfr); + } +} + #ifdef CONFIG_OF_BOARD_SETUP #include <libfdt.h> #include <fdt_support.h> diff --git a/include/asm-ppc/fsl_lbc.h b/include/asm-ppc/fsl_lbc.h index 51fc5c13b..e492c62a8 100644 --- a/include/asm-ppc/fsl_lbc.h +++ b/include/asm-ppc/fsl_lbc.h @@ -300,7 +300,10 @@ #define LCRR_EADC_2 0x00020000 #define LCRR_EADC_3 0x00030000 #define LCRR_EADC_4 0x00000000 -#define LCRR_CLKDIV 0x0000000F +/* CLKDIV is five bits only on 8536, 8572, and 8610, so far, but the fifth bit + * should always be zero on older parts that have a four bit CLKDIV. + */ +#define LCRR_CLKDIV 0x0000001F #define LCRR_CLKDIV_SHIFT 0 #define LCRR_CLKDIV_2 0x00000002 #define LCRR_CLKDIV_4 0x00000004 diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index aade097fa..2bb50b47f 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -89,6 +89,9 @@ typedef struct global_data { #if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8536) u32 sdhc_clk; #endif +#if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) + u32 lbc_clk; +#endif /* CONFIG_MPC85xx || CONFIG_MPC86xx */ #if defined(CONFIG_MPC83XX) || defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) u32 i2c1_clk; u32 i2c2_clk; diff --git a/include/asm-ppc/io.h b/include/asm-ppc/io.h index 64cb746b1..4ddad26e8 100644 --- a/include/asm-ppc/io.h +++ b/include/asm-ppc/io.h @@ -10,6 +10,10 @@ #include <linux/config.h> #include <asm/byteorder.h> +#ifdef CONFIG_ADDR_MAP +#include <addr_map.h> +#endif + #define SIO_CONFIG_RA 0x398 #define SIO_CONFIG_RD 0x399 @@ -287,7 +291,11 @@ extern inline void out_be32(volatile unsigned __iomem *addr, int val) static inline void * map_physmem(phys_addr_t paddr, unsigned long len, unsigned long flags) { +#ifdef CONFIG_ADDR_MAP + return (void *)(addrmap_phys_to_virt(paddr)); +#else return (void *)((unsigned long)paddr); +#endif } /* @@ -300,7 +308,11 @@ static inline void unmap_physmem(void *vaddr, unsigned long flags) static inline phys_addr_t virt_to_phys(void * vaddr) { +#ifdef CONFIG_ADDR_MAP + return addrmap_virt_to_phys(vaddr); +#else return (phys_addr_t)((unsigned long)vaddr); +#endif } #endif diff --git a/include/asm-ppc/mmu.h b/include/asm-ppc/mmu.h index 8975e6c90..6d942d083 100644 --- a/include/asm-ppc/mmu.h +++ b/include/asm-ppc/mmu.h @@ -431,6 +431,9 @@ extern void set_tlb(u8 tlb, u32 epn, u64 rpn, extern void disable_tlb(u8 esel); extern void invalidate_tlb(u8 tlb); extern void init_tlbs(void); +#ifdef CONFIG_ADDR_MAP +extern void init_addr_map(void); +#endif extern unsigned int setup_ddr_tlbs(unsigned int memsize_in_meg); #define SET_TLB_ENTRY(_tlb, _epn, _rpn, _perms, _wimge, _ts, _esel, _sz, _iprot) \ diff --git a/include/configs/XPEDITE5200.h b/include/configs/XPEDITE5200.h new file mode 100644 index 000000000..1df6855cc --- /dev/null +++ b/include/configs/XPEDITE5200.h @@ -0,0 +1,546 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2004-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * xpedite5200 board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ +#define CONFIG_MPC8548 1 +#define CONFIG_XPEDITE5200 1 +#define CONFIG_SYS_BOARD_NAME "XPedite5200" +#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ +#define CONFIG_RELOC_FIXUP_WORKS /* Fully relocate to SDRAM */ + +#define CONFIG_PCI 1 /* Enable PCI/PCIE */ +#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CONFIG_PCI1 1 /* PCI controller 1 */ +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +/* + * DDR config + */ +#define CONFIG_FSL_DDR2 +#undef CONFIG_FSL_DDR_INTERACTIVE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_DDR_SPD +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#define SPD_EEPROM_ADDRESS 0x54 +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 +#define CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM + +#define CONFIG_SYS_CLK_FREQ 66666666 + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR + 0x8000) + +/* + * Diagnostics + */ +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x20000000 + +/* + * Memory map + * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable + * 0x8000_0000 0xbfff_ffff PCI1 Mem 1G non-cacheable + * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable + * 0xe800_0000 0xe87f_ffff PCI1 IO 8M non-cacheable + * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable + * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable + * 0xf800_0000 0xfbff_ffff NOR Flash 2 64M non-cacheable + * 0xfc00_0000 0xffff_ffff NOR Flash 1 64M non-cacheable + */ + +#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3) + +/* + * NAND flash configuration + */ +#define CONFIG_SYS_NAND_BASE 0xef800000 +#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_NAND_ACTL +#define CONFIG_SYS_NAND_ACTL_CLE (1 << 3) /* ADDR3 is CLE */ +#define CONFIG_SYS_NAND_ACTL_ALE (1 << 4) /* ADDR4 is ALE */ +#define CONFIG_SYS_NAND_ACTL_NCE (0) /* NCE not controlled by ADDR */ +#define CONFIG_SYS_NAND_ACTL_DELAY 25 + +/* + * NOR flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xfc000000 +#define CONFIG_SYS_FLASH_BASE2 0xf8000000 +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ + {0xfbf40000, 0xc0000} } +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +/* + * Chip select configuration + */ +/* NOR Flash 0 on CS0 */ +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ + BR_PS_16 | \ + BR_V) +#define CONFIG_SYS_OR0_PRELIM (OR_AM_64MB | \ + OR_GPCM_ACS_DIV4 | \ + OR_GPCM_SCY_8) + +/* NOR Flash 1 on CS1 */ +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ + BR_PS_16 | \ + BR_V) +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM + +/* NAND flash on CS2 */ +#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ + BR_PS_8 | \ + BR_V) + +/* NAND flash on CS2 */ +#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ + OR_GPCM_BCTLD | \ + OR_GPCM_CSNT | \ + OR_GPCM_ACS_DIV4 | \ + OR_GPCM_SCY_4 | \ + OR_GPCM_TRLX | \ + OR_GPCM_EHTR) + +/* NAND flash on CS3 */ +#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ + BR_PS_8 | \ + BR_V) +#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM + +/* + * Use L1 as initial stack + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 +#define CONFIG_SYS_INIT_RAM_END 0x4000 + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} +#define CONFIG_BAUDRATE 115200 +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Use the HUSH parser + */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE + +/* I2C EEPROM */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ + +/* I2C RTC */ +#define CONFIG_RTC_M41T11 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 2000 + +/* GPIO */ +#define CONFIG_PCA953X +#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 +#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x19 +#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 + +/* PCA957 @ 0x18 */ +#define CONFIG_SYS_PCA953X_BRD_CFG0 0x01 +#define CONFIG_SYS_PCA953X_BRD_CFG1 0x02 +#define CONFIG_SYS_PCA953X_BRD_CFG2 0x04 +#define CONFIG_SYS_PCA953X_XMC_ROOT0 0x08 +#define CONFIG_SYS_PCA953X_FLASH_PASS_CS 0x10 +#define CONFIG_SYS_PCA953X_FLASH_WP 0x20 +#define CONFIG_SYS_PCA953X_MONARCH 0x40 +#define CONFIG_SYS_PCA953X_EREADY 0x80 + +/* PCA957 @ 0x19 */ +#define CONFIG_SYS_PCA953X_P14_IO0 0x01 +#define CONFIG_SYS_PCA953X_P14_IO1 0x02 +#define CONFIG_SYS_PCA953X_P14_IO2 0x04 +#define CONFIG_SYS_PCA953X_P14_IO3 0x08 +#define CONFIG_SYS_PCA953X_P14_IO4 0x10 +#define CONFIG_SYS_PCA953X_P14_IO5 0x20 +#define CONFIG_SYS_PCA953X_P14_IO6 0x40 +#define CONFIG_SYS_PCA953X_P14_IO7 0x80 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x40000000 /* 1G */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xe8000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 1M */ + +/* + * Networking options + */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC1_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define CONFIG_HAS_ETH0 + +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define TSEC2_FLAGS TSEC_GIGABIT +#define TSEC2_PHY_ADDR 2 +#define TSEC2_PHYIDX 0 +#define CONFIG_HAS_ETH1 + +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "eTSEC3" +#define TSEC3_FLAGS TSEC_GIGABIT +#define TSEC3_PHY_ADDR 3 +#define TSEC3_PHYIDX 0 +#define CONFIG_HAS_ETH2 + +#define CONFIG_TSEC4 1 +#define CONFIG_TSEC4_NAME "eTSEC4" +#define TSEC4_FLAGS TSEC_GIGABIT +#define TSEC4_PHY_ADDR 4 +#define TSEC4_PHYIDX 0 +#define CONFIG_HAS_ETH3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY + +/* + * Command configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ENV +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCA953X +#define CONFIG_CMD_PCA953X_INFO +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_SNTP + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ +#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ +#define CONFIG_PANIC_HANG /* do not reset board on panic */ +#define CONFIG_PREBOOT /* enable preboot variable */ +#define CONFIG_FIT 1 +#define CONFIG_FIT_VERBOSE 1 +#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ +#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ + +/* + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Environment Configuration + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ +#define CONFIG_ENV_SIZE 0x8000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) + +/* + * Flash memory map: + * fff80000 - ffffffff Pri U-Boot (512 KB) + * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) + * fff00000 - fff3ffff Pri FDT (256KB) + * fef00000 - ffefffff Pri OS image (16MB) + * fc000000 - feefffff Pri OS Use/Filesystem (47MB) + * + * fbf80000 - fbffffff Sec U-Boot (512 KB) + * fbf40000 - fbf7ffff Sec U-Boot Environment (256 KB) + * fbf00000 - fbf3ffff Sec FDT (256KB) + * faf00000 - fbefffff Sec OS image (16MB) + * f8000000 - faefffff Sec OS Use/Filesystem (47MB) + */ +#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000) +#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xfbf80000) +#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000) +#define CONFIG_FDT2_ENV_ADDR MK_STR(0xfbf00000) +#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000) +#define CONFIG_OS2_ENV_ADDR MK_STR(0xfaf00000) + +#define CONFIG_PROG_UBOOT1 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_UBOOT2 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_BOOT_OS_NET \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "if test -n $fdtaddr; then " \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "bootm $osaddr - $fdtaddr; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi; " \ + "else; " \ + "bootm $osaddr; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS1 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS2 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT1 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT2 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=yes\0" \ + "download_cmd=tftp\0" \ + "console_args=console=ttyS0,115200\0" \ + "root_args=root=/dev/nfs rw\0" \ + "misc_args=ip=on\0" \ + "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ + "bootfile=/home/user/file\0" \ + "osfile=/home/user/uImage-XPedite5200\0" \ + "fdtfile=/home/user/xpedite5200.dtb\0" \ + "ubootfile=/home/user/u-boot.bin\0" \ + "fdtaddr=c00000\0" \ + "osaddr=0x1000000\0" \ + "loadaddr=0x1000000\0" \ + "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ + "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ + "prog_os1="CONFIG_PROG_OS1"\0" \ + "prog_os2="CONFIG_PROG_OS2"\0" \ + "prog_fdt1="CONFIG_PROG_FDT1"\0" \ + "prog_fdt2="CONFIG_PROG_FDT2"\0" \ + "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ + "bootcmd_flash1=run set_bootargs; " \ + "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ + "bootcmd_flash2=run set_bootargs; " \ + "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ + "bootcmd=run bootcmd_flash1\0" +#endif /* __CONFIG_H */ diff --git a/include/configs/XPEDITE5370.h b/include/configs/XPEDITE5370.h new file mode 100644 index 000000000..3bc0fe8f6 --- /dev/null +++ b/include/configs/XPEDITE5370.h @@ -0,0 +1,589 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * xpedite5370 board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ +#define CONFIG_MPC8572 1 +#define CONFIG_XPEDITE5370 1 +#define CONFIG_SYS_BOARD_NAME "XPedite5370" +#define CONFIG_NUM_CPUS 2 /* 2 Cores */ +#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ +#define CONFIG_RELOC_FIXUP_WORKS /* Fully relocate to SDRAM */ + +#define CONFIG_PCI 1 /* Enable PCI/PCIE */ +#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CONFIG_PCIE1 1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 1 /* PCIE controler 2 */ +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ +#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +/* + * DDR config + */ +#define CONFIG_FSL_DDR2 +#undef CONFIG_FSL_DDR_INTERACTIVE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_DDR_SPD +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ +#define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ +#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ +#define CONFIG_NUM_DDR_CONTROLLERS 2 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 1 +#define CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM + +#ifndef __ASSEMBLY__ +extern unsigned long get_board_sys_clk(unsigned long dummy); +extern unsigned long get_board_ddr_clk(unsigned long dummy); +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0xa000) +#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000) + +/* + * Diagnostics + */ +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x20000000 + +/* + * Memory map + * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable + * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable + * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable + * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable + * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable + * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable + * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable + * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable + * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable + * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable + */ + +#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3) + +/* + * NAND flash configuration + */ +#define CONFIG_SYS_NAND_BASE 0xef800000 +#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ + +/* + * NOR flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xf8000000 +#define CONFIG_SYS_FLASH_BASE2 0xf0000000 +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ + {0xf7f40000, 0xc0000} } +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +/* + * Chip select configuration + */ +/* NOR Flash 0 on CS0 */ +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ + BR_PS_16 | \ + BR_V) +#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ + OR_GPCM_CSNT | \ + OR_GPCM_XACS | \ + OR_GPCM_ACS_DIV2 | \ + OR_GPCM_SCY_8 | \ + OR_GPCM_TRLX | \ + OR_GPCM_EHTR | \ + OR_GPCM_EAD) + +/* NOR Flash 1 on CS1 */ +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ + BR_PS_16 | \ + BR_V) +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM + +/* NAND flash on CS2 */ +#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ + (2<<BR_DECC_SHIFT) | \ + BR_PS_8 | \ + BR_MS_FCM | \ + BR_V) + +/* NAND flash on CS2 */ +#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ + OR_FCM_PGS | \ + OR_FCM_CSCT | \ + OR_FCM_CST | \ + OR_FCM_CHT | \ + OR_FCM_SCY_1 | \ + OR_FCM_TRLX | \ + OR_FCM_EHTR) + +/* NAND flash on CS3 */ +#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ + (2<<BR_DECC_SHIFT) | \ + BR_PS_8 | \ + BR_MS_FCM | \ + BR_V) +#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM + +/* + * Use L1 as initial stack + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 +#define CONFIG_SYS_INIT_RAM_END 0x00004000 + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} +#define CONFIG_BAUDRATE 115200 +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Use the HUSH parser + */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE + +/* PEX8518 slave I2C interface */ +#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 + +/* I2C DS1631 temperature sensor */ +#define CONFIG_SYS_I2C_DS1621_ADDR 0x48 +#define CONFIG_DTT_DS1621 +#define CONFIG_DTT_SENSORS { 0 } + +/* I2C EEPROM - AT24C128B */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ + +/* I2C RTC */ +#define CONFIG_RTC_M41T11 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 2000 + +/* GPIO/EEPROM/SRAM */ +#define CONFIG_DS4510 +#define CONFIG_SYS_I2C_DS4510_ADDR 0x51 + +/* GPIO */ +#define CONFIG_PCA953X +#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 +#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c +#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e +#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f +#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 + +/* + * PU = pulled high, PD = pulled low + * I = input, O = output, IO = input/output + */ +/* PCA9557 @ 0x18*/ +#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ +#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ +#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ +#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ +#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ +#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ +#define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ +#define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ + +/* PCA9557 @ 0x1c*/ +#define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ +#define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ +#define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ +#define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ +#define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ +#define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ +#define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ +#define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ + +/* PCA9557 @ 0x1e*/ +#define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ +#define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ + +/* PCA9557 @ 0x1f */ +#define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ +#define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ +#define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ +#define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ +#define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +/* PCIE1 - VPX P1 */ +#define CONFIG_SYS_PCIE1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ + +/* PCIE2 - PEX8518 */ +#define CONFIG_SYS_PCIE2_MEM_BASE 0xc0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ + +/* + * Networking options + */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_TSEC_TBI +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_ETHPRIME "eTSEC2" + +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC1_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define CONFIG_HAS_ETH0 + +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_PHY_ADDR 2 +#define TSEC2_PHYIDX 0 +#define CONFIG_HAS_ETH1 + +/* + * Command configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DS4510 +#define CONFIG_CMD_DS4510_INFO +#define CONFIG_CMD_DTT +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ENV +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCA953X +#define CONFIG_CMD_PCA953X_INFO +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_SNTP + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ +#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ +#define CONFIG_PANIC_HANG /* do not reset board on panic */ +#define CONFIG_PREBOOT /* enable preboot variable */ +#define CONFIG_FIT 1 +#define CONFIG_FIT_VERBOSE 1 +#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ + +/* + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Environment Configuration + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ +#define CONFIG_ENV_SIZE 0x8000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) + +/* + * Flash memory map: + * fff80000 - ffffffff Pri U-Boot (512 KB) + * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) + * fff00000 - fff3ffff Pri FDT (256KB) + * fef00000 - ffefffff Pri OS image (16MB) + * f8000000 - feefffff Pri OS Use/Filesystem (111MB) + * + * f7f80000 - f7ffffff Sec U-Boot (512 KB) + * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) + * f7f00000 - f7f3ffff Sec FDT (256KB) + * f6f00000 - f7efffff Sec OS image (16MB) + * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) + */ +#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000) +#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f80000) +#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000) +#define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7f00000) +#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000) +#define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000) + +#define CONFIG_PROG_UBOOT1 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_UBOOT2 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_BOOT_OS_NET \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "if test -n $fdtaddr; then " \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "bootm $osaddr - $fdtaddr; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi; " \ + "else; " \ + "bootm $osaddr; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS1 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS2 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT1 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT2 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=yes\0" \ + "download_cmd=tftp\0" \ + "console_args=console=ttyS0,115200\0" \ + "root_args=root=/dev/nfs rw\0" \ + "misc_args=ip=on\0" \ + "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ + "bootfile=/home/user/file\0" \ + "osfile=/home/user/uImage-XPedite5370\0" \ + "fdtfile=/home/user/xpedite5370.dtb\0" \ + "ubootfile=/home/user/u-boot.bin\0" \ + "fdtaddr=c00000\0" \ + "osaddr=0x1000000\0" \ + "loadaddr=0x1000000\0" \ + "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ + "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ + "prog_os1="CONFIG_PROG_OS1"\0" \ + "prog_os2="CONFIG_PROG_OS2"\0" \ + "prog_fdt1="CONFIG_PROG_FDT1"\0" \ + "prog_fdt2="CONFIG_PROG_FDT2"\0" \ + "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ + "bootcmd_flash1=run set_bootargs; " \ + "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ + "bootcmd_flash2=run set_bootargs; " \ + "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ + "bootcmd=run bootcmd_flash1\0" +#endif /* __CONFIG_H */ diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index 528c81090..8141a46dc 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -399,25 +399,16 @@ #define CONFIG_TSEC1_NAME "eTSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "eTSEC1" -#define CONFIG_TSEC3 1 -#define CONFIG_TSEC3_NAME "eTSEC2" -#define CONFIG_TSEC4 -#define CONFIG_TSEC4_NAME "eTSEC3" #undef CONFIG_MPC85XX_FEC -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 1 -#define TSEC3_PHY_ADDR 2 -#define TSEC4_PHY_ADDR 3 +#define TSEC1_PHY_ADDR 0x19 +#define TSEC2_PHY_ADDR 0x1a #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -#define TSEC3_PHYIDX 0 -#define TSEC4_PHYIDX 0 + #define TSEC1_FLAGS TSEC_GIGABIT #define TSEC2_FLAGS TSEC_GIGABIT -#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) /* Options are: eTSEC[0-3] */ #define CONFIG_ETHPRIME "eTSEC0" @@ -464,6 +455,7 @@ /* * Miscellaneous configurable options */ +#define CONFIG_CMDLINE_EDITING /* undef to save memory */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ @@ -507,10 +499,6 @@ #define CONFIG_ETHADDR 02:E0:0C:00:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 02:E0:0C:00:01:FD -#define CONFIG_HAS_ETH2 -#define CONFIG_ETH2ADDR 02:E0:0C:00:02:FD -#define CONFIG_HAS_ETH3 -#define CONFIG_ETH3ADDR 02:E0:0C:00:03:FD #endif #define CONFIG_IPADDR 192.168.0.55 diff --git a/include/e500.h b/include/e500.h index 1971eee29..9d3c8417c 100644 --- a/include/e500.h +++ b/include/e500.h @@ -13,6 +13,7 @@ typedef struct unsigned long freqProcessor; unsigned long freqSystemBus; unsigned long freqDDRBus; + unsigned long freqLocalBus; } MPC85xx_SYS_INFO; #endif /* _ASMLANGUAGE */ diff --git a/include/mpc86xx.h b/include/mpc86xx.h index f119d5bb1..a6fdea352 100644 --- a/include/mpc86xx.h +++ b/include/mpc86xx.h @@ -84,6 +84,7 @@ typedef struct { unsigned long freqProcessor; unsigned long freqSystemBus; + unsigned long freqLocalBus; } MPC86xx_SYS_INFO; #define l1icache_enable icache_enable diff --git a/include/pca953x.h b/include/pca953x.h new file mode 100644 index 000000000..6c2b58c56 --- /dev/null +++ b/include/pca953x.h @@ -0,0 +1,39 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __PCA953X_H_ +#define __PCA953X_H_ + +#define PCA953X_IN 0x00 +#define PCA953X_OUT 0x01 +#define PCA953X_POL 0x02 +#define PCA953X_CONF 0x03 + +#define PCA953X_OUT_LOW 0 +#define PCA953X_OUT_HIGH 1 +#define PCA953X_POL_NORMAL 0 +#define PCA953X_POL_INVERT 1 +#define PCA953X_DIR_OUT 0 +#define PCA953X_DIR_IN 1 + +int pca953x_set_val(u8 chip, uint mask, uint data); +int pca953x_set_pol(u8 chip, uint mask, uint data); +int pca953x_set_dir(u8 chip, uint mask, uint data); +int pca953x_get_val(u8 chip); + +#endif /* __PCA953X_H_ */ diff --git a/lib_ppc/board.c b/lib_ppc/board.c index 289a32a64..61c29b563 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -75,6 +75,10 @@ #include <keyboard.h> #endif +#ifdef CONFIG_ADDR_MAP +#include <asm/mmu.h> +#endif + #ifdef CONFIG_SYS_UPDATE_FLASH_SIZE extern int update_flash_size (int flash_size); #endif @@ -694,6 +698,10 @@ void board_init_r (gd_t *id, ulong dest_addr) */ trap_init (dest_addr); +#if defined(CONFIG_ADDR_MAP) && defined(CONFIG_E500) + init_addr_map(); +#endif + #if defined(CONFIG_BOARD_EARLY_INIT_R) board_early_init_r (); #endif |