| Age | Commit message (Collapse) | Author |
|---|
|
Copied the GPIO configurator written for the Linux kernel.
The Nomadik db8500 GPIO driver. Purpose is to be able
to just cut-n-paste the GPIO config from Linux to U-boot.
Also at the same time remove the obsolete and old
gpio_alt_funcenable/disable methods.
Now all is configured using a table in u8500.c.
Now drivers doesn't have to worry about setting up the GPIO pins.
Actually no driver today uses GPIO pins directly, only via
hardware blocks within db8500. Functions are still added
to be able to interact directly with a GPIO pin. This also
cleaned up a lot of driver by not having to bit manipulate GPIO
registers them self.
The new driver is called db8500_gpio and placed in driver/gpio/.
Functions are in include/db8500_gpio.h:
void db8500_gpio_set_pull(unsigned gpio, enum db8500_gpio_pull pull);
void db8500_gpio_make_input(unsigned gpio);
int db8500_gpio_get_input(unsigned gpio);
void db8500_gpio_make_output(unsigned gpio, int val);
void db8500_gpio_set_output(unsigned gpio, int val);
And for the configurator in include/db8500_pincfg.h:
void db8500_gpio_config_pins(pin_cfg_t *cfgs, size_t num);
All in all the final binary size has decreased.
This is only done for db8500 nomadik GPIO. The code for gpio
expanders has not been touched.
All references to Nomadik has been removed in this driver.
Only db8500 is left.
ST-Ericsson ID: None
Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com>
Change-Id: I90aa1d46c813ffb5a777c3492b5751f5054f71cf
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9904
Reviewed-by: QATOOLS
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
common.h and gpio.h were present in the u8500 board directory and in the
SoC include directory include/asm-arch/arch-stw8500.
This patch removes the duplicates in the board directory and replaces
all "common.h" and "gpio.h" with <asm/arch/common.h> and
<asm/arch/gpio.h>, respectively.
Change-Id: I4ff2a3a11324200222e3ae5b9d22eee6427f6d4c
Signed-off-by: Michael Brandt <michael.brandt@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/8838
Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com>
Reviewed-by: Rikard OLSSON <rikard.p.olsson@stericsson.com>
|
|
Moved enabling of clocks into i2c driver, making it possible to use all i2c
from 0 to 3.
Changed sanity check of i2c_read function to make it possible read from
devices with 2 byte address.
ST-Ericsson ID: CR275232
Change-Id: I6c9c2efe20dcb6903419ba531a86228a5f4491ca
Signed-off-by: Robert Rosengren <robert.rosengren@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/8340
Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com>
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
|
|
This patch is part of WP254081 which depends on WP252006.
* Fixed I2C, use real timeouts instead of counter
* Undefined CONFIG_BOOTTIME, since it as to be changed to new timer.c
* Merged V1 patches from Bangalore
The patches were merged manually, because of the differences
of the U-Boot baseline (Bangalore U-Boot 1.3.1, Lund 2009.11).
The original patches were created by Rabin Vincent
<rabin.vincent@stericsson.com>.
and were applied originally to
Branches: blr_lsp, remotes/origin/blr_lsp
Follows: qpppaaa_20100210_094651
0001-u8500-gpio-add-I2C0-altfun.patch
0002-u8500-use-correct-v1-macros.patch
0003-emmc-clean-up-paritioning.patch
0004-u8500-remove-incorrect-ram-settings.patch
0005-u8500-gpio-remove-unnecessary-ifdefs.patch
0006-u8500-add-ED-v1-detection-and-handle-eMMC-diff.patch
0008-u8500-mmc-don-t-disable-altfuns.patch
0009-u8500-gpio-remove-unused-defined.patch
0010-u8500-mmc-add-barrier-for-while-loop.patch
0011-u8500-mmc-handle-non-block-addressed-cards.patch
0012-u8500-mmc-remove-unused-gpio-settings-on-v1.patch
0013-u8500-emmc-build-fix.patch
0014-u8500-handle-v1-gpios-and-clocks.patch
0015-mmc-build-fix-for-block-addressing.patch
0016-u8500-add-clocks-and-hardware-files.patch
0017-u8500-enable-PRCUM-timers-reg-for-ED.patch
0018-u8500-handle-MTU-for-v1-ED.patch
0019-u8500-emmc-remove-unnecessary-GPIO-settings.patch
0020-u8500-remove-dead-code.patch
0021-u8500-add-working-MTU-timer.patch
0022-pl011-empty-rx-fifo-if-necessary.patch
0023-u8500-gpio-fix-cont-handling-in-altfunc.patch
0024-u8500-reduce-bootdelay-to-1-and-enable-zero-check.patch
0025-u8500-disable-forcing-of-verify-but-set-n-by-default.patch
0029-u8500-fix-some-gpio-settings.patch
0030-emmc-make-v1-paritioning-differences-explicit.patch
Signed-off-by: Michael Brandt <Michael.Brandt@stericsson.com>
Change-Id: I1106702e393c34f630e71f071e06c3952b0d3a1a
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/182
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
These are the patches for WP252006.
There will be a follow-up patched for WP254081.
Environment settings
* board_id bootargs parameter from board_id environment var
set in board_late_init().
* decreased bootdelay to 1 second
* added check for keypress on bootdelay==0
* removed preboot command and introduced "run cmdfile" instead
* changed rootfstype from ext2 to ext3
General I2C refactoring
* include/configs/u8500.h:
Enabled i2c command line commands.
Changed environment settings to use board_id as set in
board_late_init().
Added I2C address and configuration defines.
* board/st/u8500/Makefile: Replaced i2c.o with u8500_i2c.o.
* board/st/u8500/gpio.c, gpio.h: Added I2C busses to altfunc_table.
* board/st/u8500/init_mmc.c: removed config_extended_gpio() and therefore I2C
references. GPIOE settings are now in board_late_init().
* board/st/u8500/u8500.c:
Removed I2C/SD gpio settings from addr,value array.
board_late_init():
Determine and set board_id environment variable
0: mop500, 1: href500
Above boards have different GPIO expander chips which we can
distinguish by the chip id (1 and 3).
The board_id environment variable is needed for the Linux bootargs.
Signed-off-by: Michael Brandt <Michael.Brandt@stericsson.com>
Change-Id: I4c2cab28c1cb74692e0c72b2daa422e97787ff8d
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/167
Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
