diff options
24 files changed, 5853 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/sja1105.txt b/Documentation/devicetree/bindings/net/dsa/sja1105.txt new file mode 100644 index 000000000000..13fd21074d48 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/sja1105.txt @@ -0,0 +1,156 @@ +NXP SJA1105 switch driver +========================= + +Required properties: + +- compatible: + Must be one of: + - "nxp,sja1105e" + - "nxp,sja1105t" + - "nxp,sja1105p" + - "nxp,sja1105q" + - "nxp,sja1105r" + - "nxp,sja1105s" + + Although the device ID could be detected at runtime, explicit bindings + are required in order to be able to statically check their validity. + For example, SGMII can only be specified on port 4 of R and S devices, + and the non-SGMII devices, while pin-compatible, are not equal in terms + of support for RGMII internal delays (supported on P/Q/R/S, but not on + E/T). + +Optional properties: + +- sja1105,role-mac: +- sja1105,role-phy: + Boolean properties that can be assigned under each port node. By + default (unless otherwise specified) a port is configured as MAC if it + is driving a PHY (phy-handle is present) or as PHY if it is PHY-less + (fixed-link specified, presumably because it is connected to a MAC). + The effect of this property (in either its implicit or explicit form) + is: + - In the case of MII or RMII it specifies whether the SJA1105 port is a + clock source or sink for this interface (not applicable for RGMII + where there is a Tx and an Rx clock). + - In the case of RGMII it affects the behavior regarding internal + delays: + 1. If sja1105,role-mac is specified, and the phy-mode property is one + of "rgmii-id", "rgmii-txid" or "rgmii-rxid", then the entity + designated to apply the delay/clock skew necessary for RGMII + is the PHY. The SJA1105 MAC does not apply any internal delays. + 2. If sja1105,role-phy is specified, and the phy-mode property is one + of the above, the designated entity to apply the internal delays + is the SJA1105 MAC (if hardware-supported). This is only supported + by the second-generation (P/Q/R/S) hardware. On a first-generation + E or T device, it is an error to specify an RGMII phy-mode other + than "rgmii" for a port that is in fixed-link mode. In that case, + the clock skew must either be added by the MAC at the other end of + the fixed-link, or by PCB serpentine traces on the board. + These properties are required, for example, in the case where SJA1105 + ports are at both ends of a MII/RMII PHY-less setup. One end would need + to have sja1105,role-mac, while the other sja1105,role-phy. + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for the list of standard +DSA required and optional properties. + +Other observations +------------------ + +The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944) of at least +one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum +cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed +depends on the SPI bus master driver. + +Example +------- + +Ethernet switch connected via SPI to the host, CPU port wired to enet2: + +arch/arm/boot/dts/ls1021a-tsn.dts: + +/* SPI controller of the LS1021 */ +&dspi0 { + sja1105@1 { + reg = <0x1>; + #address-cells = <1>; + #size-cells = <0>; + compatible = "nxp,sja1105t"; + spi-max-frequency = <4000000>; + fsl,spi-cs-sck-delay = <1000>; + fsl,spi-sck-cs-delay = <1000>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + /* ETH5 written on chassis */ + label = "swp5"; + phy-handle = <&rgmii_phy6>; + phy-mode = "rgmii-id"; + reg = <0>; + /* Implicit "sja1105,role-mac;" */ + }; + port@1 { + /* ETH2 written on chassis */ + label = "swp2"; + phy-handle = <&rgmii_phy3>; + phy-mode = "rgmii-id"; + reg = <1>; + /* Implicit "sja1105,role-mac;" */ + }; + port@2 { + /* ETH3 written on chassis */ + label = "swp3"; + phy-handle = <&rgmii_phy4>; + phy-mode = "rgmii-id"; + reg = <2>; + /* Implicit "sja1105,role-mac;" */ + }; + port@3 { + /* ETH4 written on chassis */ + phy-handle = <&rgmii_phy5>; + label = "swp4"; + phy-mode = "rgmii-id"; + reg = <3>; + /* Implicit "sja1105,role-mac;" */ + }; + port@4 { + /* Internal port connected to eth2 */ + ethernet = <&enet2>; + phy-mode = "rgmii"; + reg = <4>; + /* Implicit "sja1105,role-phy;" */ + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +/* MDIO controller of the LS1021 */ +&mdio0 { + /* BCM5464 */ + rgmii_phy3: ethernet-phy@3 { + reg = <0x3>; + }; + rgmii_phy4: ethernet-phy@4 { + reg = <0x4>; + }; + rgmii_phy5: ethernet-phy@5 { + reg = <0x5>; + }; + rgmii_phy6: ethernet-phy@6 { + reg = <0x6>; + }; +}; + +/* Ethernet master port of the LS1021 */ +&enet2 { + phy-connection-type = "rgmii"; + status = "ok"; + fixed-link { + speed = <1000>; + full-duplex; + }; +}; diff --git a/Documentation/networking/dsa/index.rst b/Documentation/networking/dsa/index.rst index 5c488d345a1e..0e5b7a9be406 100644 --- a/Documentation/networking/dsa/index.rst +++ b/Documentation/networking/dsa/index.rst @@ -8,3 +8,4 @@ Distributed Switch Architecture dsa bcm_sf2 lan9303 + sja1105 diff --git a/Documentation/networking/dsa/sja1105.rst b/Documentation/networking/dsa/sja1105.rst new file mode 100644 index 000000000000..7c13b40915c0 --- /dev/null +++ b/Documentation/networking/dsa/sja1105.rst @@ -0,0 +1,166 @@ +========================= +NXP SJA1105 switch driver +========================= + +Overview +======== + +The NXP SJA1105 is a family of 6 devices: + +- SJA1105E: First generation, no TTEthernet +- SJA1105T: First generation, TTEthernet +- SJA1105P: Second generation, no TTEthernet, no SGMII +- SJA1105Q: Second generation, TTEthernet, no SGMII +- SJA1105R: Second generation, no TTEthernet, SGMII +- SJA1105S: Second generation, TTEthernet, SGMII + +These are SPI-managed automotive switches, with all ports being gigabit +capable, and supporting MII/RMII/RGMII and optionally SGMII on one port. + +Being automotive parts, their configuration interface is geared towards +set-and-forget use, with minimal dynamic interaction at runtime. They +require a static configuration to be composed by software and packed +with CRC and table headers, and sent over SPI. + +The static configuration is composed of several configuration tables. Each +table takes a number of entries. Some configuration tables can be (partially) +reconfigured at runtime, some not. Some tables are mandatory, some not: + +============================= ================== ============================= +Table Mandatory Reconfigurable +============================= ================== ============================= +Schedule no no +Schedule entry points if Scheduling no +VL Lookup no no +VL Policing if VL Lookup no +VL Forwarding if VL Lookup no +L2 Lookup no no +L2 Policing yes no +VLAN Lookup yes yes +L2 Forwarding yes partially (fully on P/Q/R/S) +MAC Config yes partially (fully on P/Q/R/S) +Schedule Params if Scheduling no +Schedule Entry Points Params if Scheduling no +VL Forwarding Params if VL Forwarding no +L2 Lookup Params no partially (fully on P/Q/R/S) +L2 Forwarding Params yes no +Clock Sync Params no no +AVB Params no no +General Params yes partially +Retagging no yes +xMII Params yes no +SGMII no yes +============================= ================== ============================= + + +Also the configuration is write-only (software cannot read it back from the +switch except for very few exceptions). + +The driver creates a static configuration at probe time, and keeps it at +all times in memory, as a shadow for the hardware state. When required to +change a hardware setting, the static configuration is also updated. +If that changed setting can be transmitted to the switch through the dynamic +reconfiguration interface, it is; otherwise the switch is reset and +reprogrammed with the updated static configuration. + +Switching features +================== + +The driver supports the configuration of L2 forwarding rules in hardware for +port bridging. The forwarding, broadcast and flooding domain between ports can +be restricted through two methods: either at the L2 forwarding level (isolate +one bridge's ports from another's) or at the VLAN port membership level +(isolate ports within the same bridge). The final forwarding decision taken by +the hardware is a logical AND of these two sets of rules. + +The hardware tags all traffic internally with a port-based VLAN (pvid), or it +decodes the VLAN information from the 802.1Q tag. Advanced VLAN classification +is not possible. Once attributed a VLAN tag, frames are checked against the +port's membership rules and dropped at ingress if they don't match any VLAN. +This behavior is available when switch ports are enslaved to a bridge with +``vlan_filtering 1``. + +Normally the hardware is not configurable with respect to VLAN awareness, but +by changing what TPID the switch searches 802.1Q tags for, the semantics of a +bridge with ``vlan_filtering 0`` can be kept (accept all traffic, tagged or +untagged), and therefore this mode is also supported. + +Segregating the switch ports in multiple bridges is supported (e.g. 2 + 2), but +all bridges should have the same level of VLAN awareness (either both have +``vlan_filtering`` 0, or both 1). Also an inevitable limitation of the fact +that VLAN awareness is global at the switch level is that once a bridge with +``vlan_filtering`` enslaves at least one switch port, the other un-bridged +ports are no longer available for standalone traffic termination. + +Device Tree bindings and board design +===================================== + +This section references ``Documentation/devicetree/bindings/net/dsa/sja1105.txt`` +and aims to showcase some potential switch caveats. + +RMII PHY role and out-of-band signaling +--------------------------------------- + +In the RMII spec, the 50 MHz clock signals are either driven by the MAC or by +an external oscillator (but not by the PHY). +But the spec is rather loose and devices go outside it in several ways. +Some PHYs go against the spec and may provide an output pin where they source +the 50 MHz clock themselves, in an attempt to be helpful. +On the other hand, the SJA1105 is only binary configurable - when in the RMII +MAC role it will also attempt to drive the clock signal. To prevent this from +happening it must be put in RMII PHY role. +But doing so has some unintended consequences. +In the RMII spec, the PHY can transmit extra out-of-band signals via RXD[1:0]. +These are practically some extra code words (/J/ and /K/) sent prior to the +preamble of each frame. The MAC does not have this out-of-band signaling +mechanism defined by the RMII spec. +So when the SJA1105 port is put in PHY role to avoid having 2 drivers on the +clock signal, inevitably an RMII PHY-to-PHY connection is created. The SJA1105 +emulates a PHY interface fully and generates the /J/ and /K/ symbols prior to +frame preambles, which the real PHY is not expected to understand. So the PHY +simply encodes the extra symbols received from the SJA1105-as-PHY onto the +100Base-Tx wire. +On the other side of the wire, some link partners might discard these extra +symbols, while others might choke on them and discard the entire Ethernet +frames that follow along. This looks like packet loss with some link partners +but not with others. +The take-away is that in RMII mode, the SJA1105 must be let to drive the +reference clock if connected to a PHY. + +RGMII fixed-link and internal delays +------------------------------------ + +As mentioned in the bindings document, the second generation of devices has +tunable delay lines as part of the MAC, which can be used to establish the +correct RGMII timing budget. +When powered up, these can shift the Rx and Tx clocks with a phase difference +between 73.8 and 101.7 degrees. +The catch is that the delay lines need to lock onto a clock signal with a +stable frequency. This means that there must be at least 2 microseconds of +silence between the clock at the old vs at the new frequency. Otherwise the +lock is lost and the delay lines must be reset (powered down and back up). +In RGMII the clock frequency changes with link speed (125 MHz at 1000 Mbps, 25 +MHz at 100 Mbps and 2.5 MHz at 10 Mbps), and link speed might change during the +AN process. +In the situation where the switch port is connected through an RGMII fixed-link +to a link partner whose link state life cycle is outside the control of Linux +(such as a different SoC), then the delay lines would remain unlocked (and +inactive) until there is manual intervention (ifdown/ifup on the switch port). +The take-away is that in RGMII mode, the switch's internal delays are only +reliable if the link partner never changes link speeds, or if it does, it does +so in a way that is coordinated with the switch port (practically, both ends of +the fixed-link are under control of the same Linux system). +As to why would a fixed-link interface ever change link speeds: there are +Ethernet controllers out there which come out of reset in 100 Mbps mode, and +their driver inevitably needs to change the speed and clock frequency if it's +required to work at gigabit. + +MDIO bus and PHY management +--------------------------- + +The SJA1105 does not have an MDIO bus and does not perform in-band AN either. +Therefore there is no link state notification coming from the switch device. +A board would need to hook up the PHYs connected to the switch to any other +MDIO bus available to Linux within the system (e.g. to the DSA master's MDIO +bus). Link state management then works by the driver manually keeping in sync +(over SPI commands) the MAC link speed with the settings negotiated by the PHY. diff --git a/Documentation/packing.txt b/Documentation/packing.txt new file mode 100644 index 000000000000..f830c98645f1 --- /dev/null +++ b/Documentation/packing.txt @@ -0,0 +1,149 @@ +================================================ +Generic bitfield packing and unpacking functions +================================================ + +Problem statement +----------------- + +When working with hardware, one has to choose between several approaches of +interfacing with it. +One can memory-map a pointer to a carefully crafted struct over the hardware +device's memory region, and access its fields as struct members (potentially +declared as bitfields). But writing code this way would make it less portable, +due to potential endianness mismatches between the CPU and the hardware device. +Additionally, one has to pay close attention when translating register +definitions from the hardware documentation into bit field indices for the +structs. Also, some hardware (typically networking equipment) tends to group +its register fields in ways that violate any reasonable word boundaries +(sometimes even 64 bit ones). This creates the inconvenience of having to +define "high" and "low" portions of register fields within the struct. +A more robust alternative to struct field definitions would be to extract the +required fields by shifting the appropriate number of bits. But this would +still not protect from endianness mismatches, except if all memory accesses +were performed byte-by-byte. Also the code can easily get cluttered, and the +high-level idea might get lost among the many bit shifts required. +Many drivers take the bit-shifting approach and then attempt to reduce the +clutter with tailored macros, but more often than not these macros take +shortcuts that still prevent the code from being truly portable. + +The solution +------------ + +This API deals with 2 basic operations: + - Packing a CPU-usable number into a memory buffer (with hardware + constraints/quirks) + - Unpacking a memory buffer (which has hardware constraints/quirks) + into a CPU-usable number. + +The API offers an abstraction over said hardware constraints and quirks, +over CPU endianness and therefore between possible mismatches between +the two. + +The basic unit of these API functions is the u64. From the CPU's +perspective, bit 63 always means bit offset 7 of byte 7, albeit only +logically. The question is: where do we lay this bit out in memory? + +The following examples cover the memory layout of a packed u64 field. +The byte offsets in the packed buffer are always implicitly 0, 1, ... 7. +What the examples show is where the logical bytes and bits sit. + +1. Normally (no quirks), we would do it like this: + +63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 +7 6 5 4 +31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 +3 2 1 0 + +That is, the MSByte (7) of the CPU-usable u64 sits at memory offset 0, and the +LSByte (0) of the u64 sits at memory offset 7. +This corresponds to what most folks would regard to as "big endian", where +bit i corresponds to the number 2^i. This is also referred to in the code +comments as "logical" notation. + + +2. If QUIRK_MSB_ON_THE_RIGHT is set, we do it like this: + +56 57 58 59 60 61 62 63 48 49 50 51 52 53 54 55 40 41 42 43 44 45 46 47 32 33 34 35 36 37 38 39 +7 6 5 4 +24 25 26 27 28 29 30 31 16 17 18 19 20 21 22 23 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 +3 2 1 0 + +That is, QUIRK_MSB_ON_THE_RIGHT does not affect byte positioning, but +inverts bit offsets inside a byte. + + +3. If QUIRK_LITTLE_ENDIAN is set, we do it like this: + +39 38 37 36 35 34 33 32 47 46 45 44 43 42 41 40 55 54 53 52 51 50 49 48 63 62 61 60 59 58 57 56 +4 5 6 7 +7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 23 22 21 20 19 18 17 16 31 30 29 28 27 26 25 24 +0 1 2 3 + +Therefore, QUIRK_LITTLE_ENDIAN means that inside the memory region, every +byte from each 4-byte word is placed at its mirrored position compared to +the boundary of that word. + +4. If QUIRK_MSB_ON_THE_RIGHT and QUIRK_LITTLE_ENDIAN are both set, we do it + like this: + +32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 +4 5 6 7 +0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 +0 1 2 3 + + +5. If just QUIRK_LSW32_IS_FIRST is set, we do it like this: + +31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 +3 2 1 0 +63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 +7 6 5 4 + +In this case the 8 byte memory region is interpreted as follows: first +4 bytes correspond to the least significant 4-byte word, next 4 bytes to +the more significant 4-byte word. + + +6. If QUIRK_LSW32_IS_FIRST and QUIRK_MSB_ON_THE_RIGHT are set, we do it like + this: + +24 25 26 27 28 29 30 31 16 17 18 19 20 21 22 23 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 +3 2 1 0 +56 57 58 59 60 61 62 63 48 49 50 51 52 53 54 55 40 41 42 43 44 45 46 47 32 33 34 35 36 37 38 39 +7 6 5 4 + + +7. If QUIRK_LSW32_IS_FIRST and QUIRK_LITTLE_ENDIAN are set, it looks like + this: + +7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 23 22 21 20 19 18 17 16 31 30 29 28 27 26 25 24 +0 1 2 3 +39 38 37 36 35 34 33 32 47 46 45 44 43 42 41 40 55 54 53 52 51 50 49 48 63 62 61 60 59 58 57 56 +4 5 6 7 + + +8. If QUIRK_LSW32_IS_FIRST, QUIRK_LITTLE_ENDIAN and QUIRK_MSB_ON_THE_RIGHT + are set, it looks like this: + +0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 +0 1 2 3 +32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 +4 5 6 7 + + +We always think of our offsets as if there were no quirk, and we translate +them afterwards, before accessing the memory region. + +Intended use +------------ + +Drivers that opt to use this API first need to identify which of the above 3 +quirk combinations (for a total of 8) match what the hardware documentation +describes. Then they should wrap the packing() function, creating a new +xxx_packing() that calls it using the proper QUIRK_* one-hot bits set. + +The packing() function returns an int-encoded error code, which protects the +programmer against incorrect API use. The errors are not expected to occur +durring runtime, therefore it is reasonable for xxx_packing() to return void +and simply swallow those errors. Optionally it can dump stack or print the +error description. diff --git a/MAINTAINERS b/MAINTAINERS index 0af66fa919a8..25db3db8fe38 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -11120,6 +11120,12 @@ S: Maintained F: Documentation/devicetree/bindings/sound/sgtl5000.txt F: sound/soc/codecs/sgtl5000* +NXP SJA1105 ETHERNET SWITCH DRIVER +M: Vladimir Oltean <olteanv@gmail.com> +L: linux-kernel@vger.kernel.org +S: Maintained +F: drivers/net/dsa/sja1105 + NXP TDA998X DRM DRIVER M: Russell King <linux@armlinux.org.uk> S: Maintained @@ -11673,6 +11679,14 @@ L: linux-i2c@vger.kernel.org S: Orphan F: drivers/i2c/busses/i2c-pasemi.c +PACKING +M: Vladimir Oltean <olteanv@gmail.com> +L: netdev@vger.kernel.org +S: Supported +F: lib/packing.c +F: include/linux/packing.h +F: Documentation/packing.txt + PADATA PARALLEL EXECUTION MECHANISM M: Steffen Klassert <steffen.klassert@secunet.com> L: linux-crypto@vger.kernel.org diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig index 82560b710681..c6c5ecdbcaef 100644 --- a/drivers/net/dsa/Kconfig +++ b/drivers/net/dsa/Kconfig @@ -51,6 +51,8 @@ source "drivers/net/dsa/microchip/Kconfig" source "drivers/net/dsa/mv88e6xxx/Kconfig" +source "drivers/net/dsa/sja1105/Kconfig" + config NET_DSA_QCA8K tristate "Qualcomm Atheros QCA8K Ethernet switch family support" depends on NET_DSA diff --git a/drivers/net/dsa/Makefile b/drivers/net/dsa/Makefile index 82e5d794c41f..fefb6aaa82ba 100644 --- a/drivers/net/dsa/Makefile +++ b/drivers/net/dsa/Makefile @@ -18,3 +18,4 @@ obj-$(CONFIG_NET_DSA_VITESSE_VSC73XX) += vitesse-vsc73xx.o obj-y += b53/ obj-y += microchip/ obj-y += mv88e6xxx/ +obj-y += sja1105/ diff --git a/drivers/net/dsa/sja1105/Kconfig b/drivers/net/dsa/sja1105/Kconfig new file mode 100644 index 000000000000..038685bb9d57 --- /dev/null +++ b/drivers/net/dsa/sja1105/Kconfig @@ -0,0 +1,16 @@ +config NET_DSA_SJA1105 +tristate "NXP SJA1105 Ethernet switch family support" + depends on NET_DSA && SPI + select PACKING + select CRC32 + help + This is the driver for the NXP SJA1105 automotive Ethernet switch + family. These are 5-port devices and are managed over an SPI + interface. Probing is handled based on OF bindings and so is the + linkage to phylib. The driver supports the following revisions: + - SJA1105E (Gen. 1, No TT-Ethernet) + - SJA1105T (Gen. 1, TT-Ethernet) + - SJA1105P (Gen. 2, No SGMII, No TT-Ethernet) + - SJA1105Q (Gen. 2, No SGMII, TT-Ethernet) + - SJA1105R (Gen. 2, SGMII, No TT-Ethernet) + - SJA1105S (Gen. 2, SGMII, TT-Ethernet) diff --git a/drivers/net/dsa/sja1105/Makefile b/drivers/net/dsa/sja1105/Makefile new file mode 100644 index 000000000000..1c2b55fec959 --- /dev/null +++ b/drivers/net/dsa/sja1105/Makefile @@ -0,0 +1,9 @@ +obj-$(CONFIG_NET_DSA_SJA1105) += sja1105.o + +sja1105-objs := \ + sja1105_spi.o \ + sja1105_main.o \ + sja1105_ethtool.o \ + sja1105_clocking.o \ + sja1105_static_config.o \ + sja1105_dynamic_config.o \ diff --git a/drivers/net/dsa/sja1105/sja1105.h b/drivers/net/dsa/sja1105/sja1105.h new file mode 100644 index 000000000000..b0a155b57e17 --- /dev/null +++ b/drivers/net/dsa/sja1105/sja1105.h @@ -0,0 +1,153 @@ +/* SPDX-License-Identifier: GPL-2.0 + * Copyright (c) 2018, Sensor-Technik Wiedemann GmbH + * Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ +#ifndef _SJA1105_H +#define _SJA1105_H + +#include <linux/dsa/sja1105.h> +#include <net/dsa.h> +#include "sja1105_static_config.h" + +#define SJA1105_NUM_PORTS 5 +#define SJA1105_NUM_TC 8 +#define SJA1105ET_FDB_BIN_SIZE 4 +/* The hardware value is in multiples of 10 ms. + * The passed parameter is in multiples of 1 ms. + */ +#define SJA1105_AGEING_TIME_MS(ms) ((ms) / 10) + +/* Keeps the different addresses between E/T and P/Q/R/S */ +struct sja1105_regs { + u64 device_id; + u64 prod_id; + u64 status; + u64 port_control; + u64 rgu; + u64 config; + u64 rmii_pll1; + u64 pad_mii_tx[SJA1105_NUM_PORTS]; + u64 cgu_idiv[SJA1105_NUM_PORTS]; + u64 rgmii_pad_mii_tx[SJA1105_NUM_PORTS]; + u64 mii_tx_clk[SJA1105_NUM_PORTS]; + u64 mii_rx_clk[SJA1105_NUM_PORTS]; + u64 mii_ext_tx_clk[SJA1105_NUM_PORTS]; + u64 mii_ext_rx_clk[SJA1105_NUM_PORTS]; + u64 rgmii_tx_clk[SJA1105_NUM_PORTS]; + u64 rmii_ref_clk[SJA1105_NUM_PORTS]; + u64 rmii_ext_tx_clk[SJA1105_NUM_PORTS]; + u64 mac[SJA1105_NUM_PORTS]; + u64 mac_hl1[SJA1105_NUM_PORTS]; + u64 mac_hl2[SJA1105_NUM_PORTS]; + u64 qlevel[SJA1105_NUM_PORTS]; +}; + +struct sja1105_info { + u64 device_id; + /* Needed for distinction between P and R, and between Q and S + * (since the parts with/without SGMII share the same + * switch core and device_id) + */ + u64 part_no; + const struct sja1105_dynamic_table_ops *dyn_ops; + const struct sja1105_table_ops *static_ops; + const struct sja1105_regs *regs; + int (*reset_cmd)(const void *ctx, const void *data); + int (*setup_rgmii_delay)(const void *ctx, int port); + const char *name; +}; + +struct sja1105_private { + struct sja1105_static_config static_config; + bool rgmii_rx_delay[SJA1105_NUM_PORTS]; + bool rgmii_tx_delay[SJA1105_NUM_PORTS]; + const struct sja1105_info *info; + struct gpio_desc *reset_gpio; + struct spi_device *spidev; + struct dsa_switch *ds; +}; + +#include "sja1105_dynamic_config.h" + +struct sja1105_spi_message { + u64 access; + u64 read_count; + u64 address; +}; + +typedef enum { + SPI_READ = 0, + SPI_WRITE = 1, +} sja1105_spi_rw_mode_t; + +/* From sja1105_spi.c */ +int sja1105_spi_send_packed_buf(const struct sja1105_private *priv, + sja1105_spi_rw_mode_t rw, u64 reg_addr, + void *packed_buf, size_t size_bytes); +int sja1105_spi_send_int(const struct sja1105_private *priv, + sja1105_spi_rw_mode_t rw, u64 reg_addr, + u64 *value, u64 size_bytes); +int sja1105_spi_send_long_packed_buf(const struct sja1105_private *priv, + sja1105_spi_rw_mode_t rw, u64 base_addr, + void *packed_buf, u64 buf_len); +int sja1105_static_config_upload(struct sja1105_private *priv); + +extern struct sja1105_info sja1105e_info; +extern struct sja1105_info sja1105t_info; +extern struct sja1105_info sja1105p_info; +extern struct sja1105_info sja1105q_info; +extern struct sja1105_info sja1105r_info; +extern struct sja1105_info sja1105s_info; + +/* From sja1105_clocking.c */ + +typedef enum { + XMII_MAC = 0, + XMII_PHY = 1, +} sja1105_mii_role_t; + +typedef enum { + XMII_MODE_MII = 0, + XMII_MODE_RMII = 1, + XMII_MODE_RGMII = 2, +} sja1105_phy_interface_t; + +typedef enum { + SJA1105_SPEED_10MBPS = 3, + SJA1105_SPEED_100MBPS = 2, + SJA1105_SPEED_1000MBPS = 1, + SJA1105_SPEED_AUTO = 0, +} sja1105_speed_t; + +int sja1105_clocking_setup_port(struct sja1105_private *priv, int port); +int sja1105_clocking_setup(struct sja1105_private *priv); + +/* From sja1105_ethtool.c */ +void sja1105_get_ethtool_stats(struct dsa_switch *ds, int port, u64 *data); +void sja1105_get_strings(struct dsa_switch *ds, int port, + u32 stringset, u8 *data); +int sja1105_get_sset_count(struct dsa_switch *ds, int port, int sset); + +/* From sja1105_dynamic_config.c */ +int sja1105_dynamic_config_read(struct sja1105_private *priv, + enum sja1105_blk_idx blk_idx, + int index, void *entry); +int sja1105_dynamic_config_write(struct sja1105_private *priv, + enum sja1105_blk_idx blk_idx, + int index, void *entry, bool keep); + +u8 sja1105_fdb_hash(struct sja1105_private *priv, const u8 *addr, u16 vid); + +/* Common implementations for the static and dynamic configs */ +size_t sja1105_l2_forwarding_entry_packing(void *buf, void *entry_ptr, + enum packing_op op); +size_t sja1105pqrs_l2_lookup_entry_packing(void *buf, void *entry_ptr, + enum packing_op op); +size_t sja1105et_l2_lookup_entry_packing(void *buf, void *entry_ptr, + enum packing_op op); +size_t sja1105_vlan_lookup_entry_packing(void *buf, void *entry_ptr, + enum packing_op op); +size_t sja1105pqrs_mac_config_entry_packing(void *buf, void *entry_ptr, + enum packing_op op); + +#endif diff --git a/drivers/net/dsa/sja1105/sja1105_clocking.c b/drivers/net/dsa/sja1105/sja1105_clocking.c new file mode 100644 index 000000000000..94bfe0ee50a8 --- /dev/null +++ b/drivers/net/dsa/sja1105/sja1105_clocking.c @@ -0,0 +1,601 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* Copyright (c) 2016-2018, NXP Semiconductors + * Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ +#include <linux/packing.h> +#include "sja1105.h" + +#define SJA1105_SIZE_CGU_CMD 4 + +struct sja1105_cfg_pad_mii_tx { + u64 d32_os; + u64 d32_ipud; + u64 d10_os; + u64 d10_ipud; + u64 ctrl_os; + u64 ctrl_ipud; + u64 clk_os; + u64 clk_ih; + u64 clk_ipud; +}; + +/* UM10944 Table 82. + * IDIV_0_C to IDIV_4_C control registers + * (addr. 10000Bh to 10000Fh) + */ +struct sja1105_cgu_idiv { + u64 clksrc; + u64 autoblock; + u64 idiv; + u64 pd; +}; + +/* PLL_1_C control register + * + * SJA1105 E/T: UM10944 Table 81 (address 10000Ah) + * SJA1105 P/Q/R/S: UM11040 Table 116 (address 10000Ah) + */ +struct sja1105_cgu_pll_ctrl { + u64 pllclksrc; + u64 msel; + u64 autoblock; + u64 psel; + u64 direct; + u64 fbsel; + u64 bypass; + u64 pd; +}; + +enum { + CLKSRC_MII0_TX_CLK = 0x00, + CLKSRC_MII0_RX_CLK = 0x01, + CLKSRC_MII1_TX_CLK = 0x02, + CLKSRC_MII1_RX_CLK = 0x03, + CLKSRC_MII2_TX_CLK = 0x04, + CLKSRC_MII2_RX_CLK = 0x05, + CLKSRC_MII3_TX_CLK = 0x06, + CLKSRC_MII3_RX_CLK = 0x07, + CLKSRC_MII4_TX_CLK = 0x08, + CLKSRC_MII4_RX_CLK = 0x09, + CLKSRC_PLL0 = 0x0B, + CLKSRC_PLL1 = 0x0E, + CLKSRC_IDIV0 = 0x11, + CLKSRC_IDIV1 = 0x12, + CLKSRC_IDIV2 = 0x13, + CLKSRC_IDIV3 = 0x14, + CLKSRC_IDIV4 = 0x15, +}; + +/* UM10944 Table 83. + * MIIx clock control registers 1 to 30 + * (addresses 100013h to 100035h) + */ +struct sja1105_cgu_mii_ctrl { + u64 clksrc; + u64 autoblock; + u64 pd; +}; + +static void sja1105_cgu_idiv_packing(void *buf, struct sja1105_cgu_idiv *idiv, + enum packing_op op) +{ + const int size = 4; + + sja1105_packing(buf, &idiv->clksrc, 28, 24, size, op); + sja1105_packing(buf, &idiv->autoblock, 11, 11, size, op); + sja1105_packing(buf, &idiv->idiv, 5, 2, size, op); + sja1105_packing(buf, &idiv->pd, 0, 0, size, op); +} + +static int sja1105_cgu_idiv_config(struct sja1105_private *priv, int port, + bool enabled, int factor) +{ + const struct sja1105_regs *regs = priv->info->regs; + struct device *dev = priv->ds->dev; + struct sja1105_cgu_idiv idiv; + u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0}; + + if (enabled && factor != 1 && factor != 10) { + dev_err(dev, "idiv factor must be 1 or 10\n"); + return -ERANGE; + } + + /* Payload for packed_buf */ + idiv.clksrc = 0x0A; /* 25MHz */ + idiv.autoblock = 1; /* Block clk automatically */ + idiv.idiv = factor - 1; /* Divide by 1 or 10 */ + idiv.pd = enabled ? 0 : 1; /* Power down? */ + sja1105_cgu_idiv_packing(packed_buf, &idiv, PACK); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, + regs->cgu_idiv[port], packed_buf, + SJA1105_SIZE_CGU_CMD); +} + +static void +sja1105_cgu_mii_control_packing(void *buf, struct sja1105_cgu_mii_ctrl *cmd, + enum packing_op op) +{ + const int size = 4; + + sja1105_packing(buf, &cmd->clksrc, 28, 24, size, op); + sja1105_packing(buf, &cmd->autoblock, 11, 11, size, op); + sja1105_packing(buf, &cmd->pd, 0, 0, size, op); +} + +static int sja1105_cgu_mii_tx_clk_config(struct sja1105_private *priv, + int port, sja1105_mii_role_t role) +{ + const struct sja1105_regs *regs = priv->info->regs; + struct sja1105_cgu_mii_ctrl mii_tx_clk; + const int mac_clk_sources[] = { + CLKSRC_MII0_TX_CLK, + CLKSRC_MII1_TX_CLK, + CLKSRC_MII2_TX_CLK, + CLKSRC_MII3_TX_CLK, + CLKSRC_MII4_TX_CLK, + }; + const int phy_clk_sources[] = { + CLKSRC_IDIV0, + CLKSRC_IDIV1, + CLKSRC_IDIV2, + CLKSRC_IDIV3, + CLKSRC_IDIV4, + }; + u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0}; + int clksrc; + + if (role == XMII_MAC) + clksrc = mac_clk_sources[port]; + else + clksrc = phy_clk_sources[port]; + + /* Payload for packed_buf */ + mii_tx_clk.clksrc = clksrc; + mii_tx_clk.autoblock = 1; /* Autoblock clk while changing clksrc */ + mii_tx_clk.pd = 0; /* Power Down off => enabled */ + sja1105_cgu_mii_control_packing(packed_buf, &mii_tx_clk, PACK); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, + regs->mii_tx_clk[port], packed_buf, + SJA1105_SIZE_CGU_CMD); +} + +static int +sja1105_cgu_mii_rx_clk_config(struct sja1105_private *priv, int port) +{ + const struct sja1105_regs *regs = priv->info->regs; + struct sja1105_cgu_mii_ctrl mii_rx_clk; + u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0}; + const int clk_sources[] = { + CLKSRC_MII0_RX_CLK, + CLKSRC_MII1_RX_CLK, + CLKSRC_MII2_RX_CLK, + CLKSRC_MII3_RX_CLK, + CLKSRC_MII4_RX_CLK, + }; + + /* Payload for packed_buf */ + mii_rx_clk.clksrc = clk_sources[port]; + mii_rx_clk.autoblock = 1; /* Autoblock clk while changing clksrc */ + mii_rx_clk.pd = 0; /* Power Down off => enabled */ + sja1105_cgu_mii_control_packing(packed_buf, &mii_rx_clk, PACK); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, + regs->mii_rx_clk[port], packed_buf, + SJA1105_SIZE_CGU_CMD); +} + +static int +sja1105_cgu_mii_ext_tx_clk_config(struct sja1105_private *priv, int port) +{ + const struct sja1105_regs *regs = priv->info->regs; + struct sja1105_cgu_mii_ctrl mii_ext_tx_clk; + u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0}; + const int clk_sources[] = { + CLKSRC_IDIV0, + CLKSRC_IDIV1, + CLKSRC_IDIV2, + CLKSRC_IDIV3, + CLKSRC_IDIV4, + }; + + /* Payload for packed_buf */ + mii_ext_tx_clk.clksrc = clk_sources[port]; + mii_ext_tx_clk.autoblock = 1; /* Autoblock clk while changing clksrc */ + mii_ext_tx_clk.pd = 0; /* Power Down off => enabled */ + sja1105_cgu_mii_control_packing(packed_buf, &mii_ext_tx_clk, PACK); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, + regs->mii_ext_tx_clk[port], + packed_buf, SJA1105_SIZE_CGU_CMD); +} + +static int +sja1105_cgu_mii_ext_rx_clk_config(struct sja1105_private *priv, int port) +{ + const struct sja1105_regs *regs = priv->info->regs; + struct sja1105_cgu_mii_ctrl mii_ext_rx_clk; + u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0}; + const int clk_sources[] = { + CLKSRC_IDIV0, + CLKSRC_IDIV1, + CLKSRC_IDIV2, + CLKSRC_IDIV3, + CLKSRC_IDIV4, + }; + + /* Payload for packed_buf */ + mii_ext_rx_clk.clksrc = clk_sources[port]; + mii_ext_rx_clk.autoblock = 1; /* Autoblock clk while changing clksrc */ + mii_ext_rx_clk.pd = 0; /* Power Down off => enabled */ + sja1105_cgu_mii_control_packing(packed_buf, &mii_ext_rx_clk, PACK); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, + regs->mii_ext_rx_clk[port], + packed_buf, SJA1105_SIZE_CGU_CMD); +} + +static int sja1105_mii_clocking_setup(struct sja1105_private *priv, int port, + sja1105_mii_role_t role) +{ + struct device *dev = priv->ds->dev; + int rc; + + dev_dbg(dev, "Configuring MII-%s clocking\n", + (role == XMII_MAC) ? "MAC" : "PHY"); + /* If role is MAC, disable IDIV + * If role is PHY, enable IDIV and configure for 1/1 divider + */ + rc = sja1105_cgu_idiv_config(priv, port, (role == XMII_PHY), 1); + if (rc < 0) + return rc; + + /* Configure CLKSRC of MII_TX_CLK_n + * * If role is MAC, select TX_CLK_n + * * If role is PHY, select IDIV_n + */ + rc = sja1105_cgu_mii_tx_clk_config(priv, port, role); + if (rc < 0) + return rc; + + /* Configure CLKSRC of MII_RX_CLK_n + * Select RX_CLK_n + */ + rc = sja1105_cgu_mii_rx_clk_config(priv, port); + if (rc < 0) + return rc; + + if (role == XMII_PHY) { + /* Per MII spec, the PHY (which is us) drives the TX_CLK pin */ + + /* Configure CLKSRC of EXT_TX_CLK_n + * Select IDIV_n + */ + rc = sja1105_cgu_mii_ext_tx_clk_config(priv, port); + if (rc < 0) + return rc; + + /* Configure CLKSRC of EXT_RX_CLK_n + * Select IDIV_n + */ + rc = sja1105_cgu_mii_ext_rx_clk_config(priv, port); + if (rc < 0) + return rc; + } + return 0; +} + +static void +sja1105_cgu_pll_control_packing(void *buf, struct sja1105_cgu_pll_ctrl *cmd, + enum packing_op op) +{ + const int size = 4; + + sja1105_packing(buf, &cmd->pllclksrc, 28, 24, size, op); + sja1105_packing(buf, &cmd->msel, 23, 16, size, op); + sja1105_packing(buf, &cmd->autoblock, 11, 11, size, op); + sja1105_packing(buf, &cmd->psel, 9, 8, size, op); + sja1105_packing(buf, &cmd->direct, 7, 7, size, op); + sja1105_packing(buf, &cmd->fbsel, 6, 6, size, op); + sja1105_packing(buf, &cmd->bypass, 1, 1, size, op); + sja1105_packing(buf, &cmd->pd, 0, 0, size, op); +} + +static int sja1105_cgu_rgmii_tx_clk_config(struct sja1105_private *priv, + int port, sja1105_speed_t speed) +{ + const struct sja1105_regs *regs = priv->info->regs; + struct sja1105_cgu_mii_ctrl txc; + u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0}; + int clksrc; + + if (speed == SJA1105_SPEED_1000MBPS) { + clksrc = CLKSRC_PLL0; + } else { + int clk_sources[] = {CLKSRC_IDIV0, CLKSRC_IDIV1, CLKSRC_IDIV2, + CLKSRC_IDIV3, CLKSRC_IDIV4}; + clksrc = clk_sources[port]; + } + + /* RGMII: 125MHz for 1000, 25MHz for 100, 2.5MHz for 10 */ + txc.clksrc = clksrc; + /* Autoblock clk while changing clksrc */ + txc.autoblock = 1; + /* Power Down off => enabled */ + txc.pd = 0; + sja1105_cgu_mii_control_packing(packed_buf, &txc, PACK); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, + regs->rgmii_tx_clk[port], + packed_buf, SJA1105_SIZE_CGU_CMD); +} + +/* AGU */ +static void +sja1105_cfg_pad_mii_tx_packing(void *buf, struct sja1105_cfg_pad_mii_tx *cmd, + enum packing_op op) +{ + const int size = 4; + + sja1105_packing(buf, &cmd->d32_os, 28, 27, size, op); + sja1105_packing(buf, &cmd->d32_ipud, 25, 24, size, op); + sja1105_packing(buf, &cmd->d10_os, 20, 19, size, op); + sja1105_packing(buf, &cmd->d10_ipud, 17, 16, size, op); + sja1105_packing(buf, &cmd->ctrl_os, 12, 11, size, op); + sja1105_packing(buf, &cmd->ctrl_ipud, 9, 8, size, op); + sja1105_packing(buf, &cmd->clk_os, 4, 3, size, op); + sja1105_packing(buf, &cmd->clk_ih, 2, 2, size, op); + sja1105_packing(buf, &cmd->clk_ipud, 1, 0, size, op); +} + +static int sja1105_rgmii_cfg_pad_tx_config(struct sja1105_private *priv, + int port) +{ + const struct sja1105_regs *regs = priv->info->regs; + struct sja1105_cfg_pad_mii_tx pad_mii_tx; + u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0}; + + /* Payload */ + pad_mii_tx.d32_os = 3; /* TXD[3:2] output stage: */ + /* high noise/high speed */ + pad_mii_tx.d10_os = 3; /* TXD[1:0] output stage: */ + /* high noise/high speed */ + pad_mii_tx.d32_ipud = 2; /* TXD[3:2] input stage: */ + /* plain input (default) */ + pad_mii_tx.d10_ipud = 2; /* TXD[1:0] input stage: */ + /* plain input (default) */ + pad_mii_tx.ctrl_os = 3; /* TX_CTL / TX_ER output stage */ + pad_mii_tx.ctrl_ipud = 2; /* TX_CTL / TX_ER input stage (default) */ + pad_mii_tx.clk_os = 3; /* TX_CLK output stage */ + pad_mii_tx.clk_ih = 0; /* TX_CLK input hysteresis (default) */ + pad_mii_tx.clk_ipud = 2; /* TX_CLK input stage (default) */ + sja1105_cfg_pad_mii_tx_packing(packed_buf, &pad_mii_tx, PACK); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, + regs->rgmii_pad_mii_tx[port], + packed_buf, SJA1105_SIZE_CGU_CMD); +} + +static int sja1105_rgmii_clocking_setup(struct sja1105_private *priv, int port) +{ + struct device *dev = priv->ds->dev; + struct sja1105_mac_config_entry *mac; + sja1105_speed_t speed; + int rc; + + mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; + speed = mac[port].speed; + + dev_dbg(dev, "Configuring port %d RGMII at speed %dMbps\n", + port, speed); + + switch (speed) { + case SJA1105_SPEED_1000MBPS: + /* 1000Mbps, IDIV disabled (125 MHz) */ + rc = sja1105_cgu_idiv_config(priv, port, false, 1); + break; + case SJA1105_SPEED_100MBPS: + /* 100Mbps, IDIV enabled, divide by 1 (25 MHz) */ + rc = sja1105_cgu_idiv_config(priv, port, true, 1); + break; + case SJA1105_SPEED_10MBPS: + /* 10Mbps, IDIV enabled, divide by 10 (2.5 MHz) */ + rc = sja1105_cgu_idiv_config(priv, port, true, 10); + break; + case SJA1105_SPEED_AUTO: + /* Skip CGU configuration if there is no speed available + * (e.g. link is not established yet) + */ + dev_dbg(dev, "Speed not available, skipping CGU config\n"); + return 0; + default: + rc = -EINVAL; + } + + if (rc < 0) { + dev_err(dev, "Failed to configure idiv\n"); + return rc; + } + rc = sja1105_cgu_rgmii_tx_clk_config(priv, port, speed); + if (rc < 0) { + dev_err(dev, "Failed to configure RGMII Tx clock\n"); + return rc; + } + rc = sja1105_rgmii_cfg_pad_tx_config(priv, port); + if (rc < 0) { + dev_err(dev, "Failed to configure Tx pad registers\n"); + return rc; + } + if (!priv->info->setup_rgmii_delay) + return 0; + + return priv->info->setup_rgmii_delay(priv, port); +} + +static int sja1105_cgu_rmii_ref_clk_config(struct sja1105_private *priv, + int port) +{ + const struct sja1105_regs *regs = priv->info->regs; + struct sja1105_cgu_mii_ctrl ref_clk; + u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0}; + const int clk_sources[] = { + CLKSRC_MII0_TX_CLK, + CLKSRC_MII1_TX_CLK, + CLKSRC_MII2_TX_CLK, + CLKSRC_MII3_TX_CLK, + CLKSRC_MII4_TX_CLK, + }; + + /* Payload for packed_buf */ + ref_clk.clksrc = clk_sources[port]; + ref_clk.autoblock = 1; /* Autoblock clk while changing clksrc */ + ref_clk.pd = 0; /* Power Down off => enabled */ + sja1105_cgu_mii_control_packing(packed_buf, &ref_clk, PACK); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, + regs->rmii_ref_clk[port], + packed_buf, SJA1105_SIZE_CGU_CMD); +} + +static int +sja1105_cgu_rmii_ext_tx_clk_config(struct sja1105_private *priv, int port) +{ + const struct sja1105_regs *regs = priv->info->regs; + struct sja1105_cgu_mii_ctrl ext_tx_clk; + u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0}; + + /* Payload for packed_buf */ + ext_tx_clk.clksrc = CLKSRC_PLL1; + ext_tx_clk.autoblock = 1; /* Autoblock clk while changing clksrc */ + ext_tx_clk.pd = 0; /* Power Down off => enabled */ + sja1105_cgu_mii_control_packing(packed_buf, &ext_tx_clk, PACK); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, + regs->rmii_ext_tx_clk[port], + packed_buf, SJA1105_SIZE_CGU_CMD); +} + +static int sja1105_cgu_rmii_pll_config(struct sja1105_private *priv) +{ + const struct sja1105_regs *regs = priv->info->regs; + u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0}; + struct sja1105_cgu_pll_ctrl pll = {0}; + struct device *dev = priv->ds->dev; + int rc; + + /* PLL1 must be enabled and output 50 Mhz. + * This is done by writing first 0x0A010941 to + * the PLL_1_C register and then deasserting + * power down (PD) 0x0A010940. + */ + + /* Step 1: PLL1 setup for 50Mhz */ + pll.pllclksrc = 0xA; + pll.msel = 0x1; + pll.autoblock = 0x1; + pll.psel = 0x1; + pll.direct = 0x0; + pll.fbsel = 0x1; + pll.bypass = 0x0; + pll.pd = 0x1; + + sja1105_cgu_pll_control_packing(packed_buf, &pll, PACK); + rc = sja1105_spi_send_packed_buf(priv, SPI_WRITE, regs->rmii_pll1, + packed_buf, SJA1105_SIZE_CGU_CMD); + if (rc < 0) { + dev_err(dev, "failed to configure PLL1 for 50MHz\n"); + return rc; + } + + /* Step 2: Enable PLL1 */ + pll.pd = 0x0; + + sja1105_cgu_pll_control_packing(packed_buf, &pll, PACK); + rc = sja1105_spi_send_packed_buf(priv, SPI_WRITE, regs->rmii_pll1, + packed_buf, SJA1105_SIZE_CGU_CMD); + if (rc < 0) { + dev_err(dev, "failed to enable PLL1\n"); + return rc; + } + return rc; +} + +static int sja1105_rmii_clocking_setup(struct sja1105_private *priv, int port, + sja1105_mii_role_t role) +{ + struct device *dev = priv->ds->dev; + int rc; + + dev_dbg(dev, "Configuring RMII-%s clocking\n", + (role == XMII_MAC) ? "MAC" : "PHY"); + /* AH1601.pdf chapter 2.5.1. Sources */ + if (role == XMII_MAC) { + /* Configure and enable PLL1 for 50Mhz output */ + rc = sja1105_cgu_rmii_pll_config(priv); + if (rc < 0) + return rc; + } + /* Disable IDIV for this port */ + rc = sja1105_cgu_idiv_config(priv, port, false, 1); + if (rc < 0) + return rc; + /* Source to sink mappings */ + rc = sja1105_cgu_rmii_ref_clk_config(priv, port); + if (rc < 0) + return rc; + if (role == XMII_MAC) { + rc = sja1105_cgu_rmii_ext_tx_clk_config(priv, port); + if (rc < 0) + return rc; + } + return 0; +} + +int sja1105_clocking_setup_port(struct sja1105_private *priv, int port) +{ + struct sja1105_xmii_params_entry *mii; + struct device *dev = priv->ds->dev; + sja1105_phy_interface_t phy_mode; + sja1105_mii_role_t role; + int rc; + + mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries; + + /* RGMII etc */ + phy_mode = mii->xmii_mode[port]; + /* MAC or PHY, for applicable types (not RGMII) */ + role = mii->phy_mac[port]; + + switch (phy_mode) { + case XMII_MODE_MII: + rc = sja1105_mii_clocking_setup(priv, port, role); + break; + case XMII_MODE_RMII: + rc = sja1105_rmii_clocking_setup(priv, port, role); + break; + case XMII_MODE_RGMII: + rc = sja1105_rgmii_clocking_setup(priv, port); + break; + default: + dev_err(dev, "Invalid interface mode specified: %d\n", + phy_mode); + return -EINVAL; + } + if (rc) + dev_err(dev, "Clocking setup for port %d failed: %d\n", + port, rc); + return rc; +} + +int sja1105_clocking_setup(struct sja1105_private *priv) +{ + int port, rc; + + for (port = 0; port < SJA1105_NUM_PORTS; port++) { + rc = sja1105_clocking_setup_port(priv, port); + if (rc < 0) + return rc; + } + return 0; +} diff --git a/drivers/net/dsa/sja1105/sja1105_dynamic_config.c b/drivers/net/dsa/sja1105/sja1105_dynamic_config.c new file mode 100644 index 000000000000..e73ab28bf632 --- /dev/null +++ b/drivers/net/dsa/sja1105/sja1105_dynamic_config.c @@ -0,0 +1,532 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ +#include "sja1105.h" + +#define SJA1105_SIZE_DYN_CMD 4 + +#define SJA1105ET_SIZE_MAC_CONFIG_DYN_ENTRY \ + SJA1105_SIZE_DYN_CMD + +#define SJA1105ET_SIZE_L2_LOOKUP_DYN_CMD \ + (SJA1105_SIZE_DYN_CMD + SJA1105ET_SIZE_L2_LOOKUP_ENTRY) + +#define SJA1105PQRS_SIZE_L2_LOOKUP_DYN_CMD \ + (SJA1105_SIZE_DYN_CMD + SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY) + +#define SJA1105_SIZE_VLAN_LOOKUP_DYN_CMD \ + (SJA1105_SIZE_DYN_CMD + 4 + SJA1105_SIZE_VLAN_LOOKUP_ENTRY) + +#define SJA1105_SIZE_L2_FORWARDING_DYN_CMD \ + (SJA1105_SIZE_DYN_CMD + SJA1105_SIZE_L2_FORWARDING_ENTRY) + +#define SJA1105ET_SIZE_MAC_CONFIG_DYN_CMD \ + (SJA1105_SIZE_DYN_CMD + SJA1105ET_SIZE_MAC_CONFIG_DYN_ENTRY) + +#define SJA1105PQRS_SIZE_MAC_CONFIG_DYN_CMD \ + (SJA1105_SIZE_DYN_CMD + SJA1105PQRS_SIZE_MAC_CONFIG_ENTRY) + +#define SJA1105ET_SIZE_L2_LOOKUP_PARAMS_DYN_CMD \ + SJA1105_SIZE_DYN_CMD + +#define SJA1105ET_SIZE_GENERAL_PARAMS_DYN_CMD \ + SJA1105_SIZE_DYN_CMD + +#define SJA1105_MAX_DYN_CMD_SIZE \ + SJA1105PQRS_SIZE_MAC_CONFIG_DYN_CMD + +static void +sja1105pqrs_l2_lookup_cmd_packing(void *buf, struct sja1105_dyn_cmd *cmd, + enum packing_op op) +{ + u8 *p = buf + SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY; + const int size = SJA1105_SIZE_DYN_CMD; + + sja1105_packing(p, &cmd->valid, 31, 31, size, op); + sja1105_packing(p, &cmd->rdwrset, 30, 30, size, op); + sja1105_packing(p, &cmd->errors, 29, 29, size, op); + sja1105_packing(p, &cmd->valident, 27, 27, size, op); + /* Hack - The hardware takes the 'index' field within + * struct sja1105_l2_lookup_entry as the index on which this command + * will operate. However it will ignore everything else, so 'index' + * is logically part of command but physically part of entry. + * Populate the 'index' entry field from within the command callback, + * such that our API doesn't need to ask for a full-blown entry + * structure when e.g. a delete is requested. + */ + sja1105_packing(buf, &cmd->index, 29, 20, + SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY, op); + /* TODO hostcmd */ +} + +static void +sja1105et_l2_lookup_cmd_packing(void *buf, struct sja1105_dyn_cmd *cmd, + enum packing_op op) +{ + u8 *p = buf + SJA1105ET_SIZE_L2_LOOKUP_ENTRY; + const int size = SJA1105_SIZE_DYN_CMD; + + sja1105_packing(p, &cmd->valid, 31, 31, size, op); + sja1105_packing(p, &cmd->rdwrset, 30, 30, size, op); + sja1105_packing(p, &cmd->errors, 29, 29, size, op); + sja1105_packing(p, &cmd->valident, 27, 27, size, op); + /* Hack - see comments above. */ + sja1105_packing(buf, &cmd->index, 29, 20, + SJA1105ET_SIZE_L2_LOOKUP_ENTRY, op); +} + +static void +sja1105et_mgmt_route_cmd_packing(void *buf, struct sja1105_dyn_cmd *cmd, + enum packing_op op) +{ + u8 *p = buf + SJA1105ET_SIZE_L2_LOOKUP_ENTRY; + u64 mgmtroute = 1; + + sja1105et_l2_lookup_cmd_packing(buf, cmd, op); + if (op == PACK) + sja1105_pack(p, &mgmtroute, 26, 26, SJA1105_SIZE_DYN_CMD); +} + +static size_t sja1105et_mgmt_route_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + struct sja1105_mgmt_entry *entry = entry_ptr; + const size_t size = SJA1105ET_SIZE_L2_LOOKUP_ENTRY; + + /* UM10944: To specify if a PTP egress timestamp shall be captured on + * each port upon transmission of the frame, the LSB of VLANID in the + * ENTRY field provided by the host must be set. + * Bit 1 of VLANID then specifies the register where the timestamp for + * this port is stored in. + */ + sja1105_packing(buf, &entry->tsreg, 85, 85, size, op); + sja1105_packing(buf, &entry->takets, 84, 84, size, op); + sja1105_packing(buf, &entry->macaddr, 83, 36, size, op); + sja1105_packing(buf, &entry->destports, 35, 31, size, op); + sja1105_packing(buf, &entry->enfport, 30, 30, size, op); + return size; +} + +/* In E/T, entry is at addresses 0x27-0x28. There is a 4 byte gap at 0x29, + * and command is at 0x2a. Similarly in P/Q/R/S there is a 1 register gap + * between entry (0x2d, 0x2e) and command (0x30). + */ +static void +sja1105_vlan_lookup_cmd_packing(void *buf, struct sja1105_dyn_cmd *cmd, + enum packing_op op) +{ + u8 *p = buf + SJA1105_SIZE_VLAN_LOOKUP_ENTRY + 4; + const int size = SJA1105_SIZE_DYN_CMD; + + sja1105_packing(p, &cmd->valid, 31, 31, size, op); + sja1105_packing(p, &cmd->rdwrset, 30, 30, size, op); + sja1105_packing(p, &cmd->valident, 27, 27, size, op); + /* Hack - see comments above, applied for 'vlanid' field of + * struct sja1105_vlan_lookup_entry. + */ + sja1105_packing(buf, &cmd->index, 38, 27, + SJA1105_SIZE_VLAN_LOOKUP_ENTRY, op); +} + +static void +sja1105_l2_forwarding_cmd_packing(void *buf, struct sja1105_dyn_cmd *cmd, + enum packing_op op) +{ + u8 *p = buf + SJA1105_SIZE_L2_FORWARDING_ENTRY; + const int size = SJA1105_SIZE_DYN_CMD; + + sja1105_packing(p, &cmd->valid, 31, 31, size, op); + sja1105_packing(p, &cmd->errors, 30, 30, size, op); + sja1105_packing(p, &cmd->rdwrset, 29, 29, size, op); + sja1105_packing(p, &cmd->index, 4, 0, size, op); +} + +static void +sja1105et_mac_config_cmd_packing(void *buf, struct sja1105_dyn_cmd *cmd, + enum packing_op op) +{ + const int size = SJA1105_SIZE_DYN_CMD; + /* Yup, user manual definitions are reversed */ + u8 *reg1 = buf + 4; + + sja1105_packing(reg1, &cmd->valid, 31, 31, size, op); + sja1105_packing(reg1, &cmd->index, 26, 24, size, op); +} + +static size_t sja1105et_mac_config_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const int size = SJA1105ET_SIZE_MAC_CONFIG_DYN_ENTRY; + struct sja1105_mac_config_entry *entry = entry_ptr; + /* Yup, user manual definitions are reversed */ + u8 *reg1 = buf + 4; + u8 *reg2 = buf; + + sja1105_packing(reg1, &entry->speed, 30, 29, size, op); + sja1105_packing(reg1, &entry->drpdtag, 23, 23, size, op); + sja1105_packing(reg1, &entry->drpuntag, 22, 22, size, op); + sja1105_packing(reg1, &entry->retag, 21, 21, size, op); + sja1105_packing(reg1, &entry->dyn_learn, 20, 20, size, op); + sja1105_packing(reg1, &entry->egress, 19, 19, size, op); + sja1105_packing(reg1, &entry->ingress, 18, 18, size, op); + sja1105_packing(reg1, &entry->ing_mirr, 17, 17, size, op); + sja1105_packing(reg1, &entry->egr_mirr, 16, 16, size, op); + sja1105_packing(reg1, &entry->vlanprio, 14, 12, size, op); + sja1105_packing(reg1, &entry->vlanid, 11, 0, size, op); + sja1105_packing(reg2, &entry->tp_delin, 31, 16, size, op); + sja1105_packing(reg2, &entry->tp_delout, 15, 0, size, op); + /* MAC configuration table entries which can't be reconfigured: + * top, base, enabled, ifg, maxage, drpnona664 + */ + /* Bogus return value, not used anywhere */ + return 0; +} + +static void +sja1105pqrs_mac_config_cmd_packing(void *buf, struct sja1105_dyn_cmd *cmd, + enum packing_op op) +{ + const int size = SJA1105ET_SIZE_MAC_CONFIG_DYN_ENTRY; + u8 *p = buf + SJA1105PQRS_SIZE_MAC_CONFIG_ENTRY; + + sja1105_packing(p, &cmd->valid, 31, 31, size, op); + sja1105_packing(p, &cmd->errors, 30, 30, size, op); + sja1105_packing(p, &cmd->rdwrset, 29, 29, size, op); + sja1105_packing(p, &cmd->index, 2, 0, size, op); +} + +static void +sja1105et_l2_lookup_params_cmd_packing(void *buf, struct sja1105_dyn_cmd *cmd, + enum packing_op op) +{ + sja1105_packing(buf, &cmd->valid, 31, 31, + SJA1105ET_SIZE_L2_LOOKUP_PARAMS_DYN_CMD, op); +} + +static size_t +sja1105et_l2_lookup_params_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + struct sja1105_l2_lookup_params_entry *entry = entry_ptr; + + sja1105_packing(buf, &entry->poly, 7, 0, + SJA1105ET_SIZE_L2_LOOKUP_PARAMS_DYN_CMD, op); + /* Bogus return value, not used anywhere */ + return 0; +} + +static void +sja1105et_general_params_cmd_packing(void *buf, struct sja1105_dyn_cmd *cmd, + enum packing_op op) +{ + const int size = SJA1105ET_SIZE_GENERAL_PARAMS_DYN_CMD; + + sja1105_packing(buf, &cmd->valid, 31, 31, size, op); + sja1105_packing(buf, &cmd->errors, 30, 30, size, op); +} + +static size_t +sja1105et_general_params_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + struct sja1105_general_params_entry *entry = entry_ptr; + const int size = SJA1105ET_SIZE_GENERAL_PARAMS_DYN_CMD; + + sja1105_packing(buf, &entry->mirr_port, 2, 0, size, op); + /* Bogus return value, not used anywhere */ + return 0; +} + +#define OP_READ BIT(0) +#define OP_WRITE BIT(1) +#define OP_DEL BIT(2) + +/* SJA1105E/T: First generation */ +struct sja1105_dynamic_table_ops sja1105et_dyn_ops[BLK_IDX_MAX_DYN] = { + [BLK_IDX_L2_LOOKUP] = { + .entry_packing = sja1105et_l2_lookup_entry_packing, + .cmd_packing = sja1105et_l2_lookup_cmd_packing, + .access = (OP_READ | OP_WRITE | OP_DEL), + .max_entry_count = SJA1105_MAX_L2_LOOKUP_COUNT, + .packed_size = SJA1105ET_SIZE_L2_LOOKUP_DYN_CMD, + .addr = 0x20, + }, + [BLK_IDX_MGMT_ROUTE] = { + .entry_packing = sja1105et_mgmt_route_entry_packing, + .cmd_packing = sja1105et_mgmt_route_cmd_packing, + .access = (OP_READ | OP_WRITE), + .max_entry_count = SJA1105_NUM_PORTS, + .packed_size = SJA1105ET_SIZE_L2_LOOKUP_DYN_CMD, + .addr = 0x20, + }, + [BLK_IDX_L2_POLICING] = {0}, + [BLK_IDX_VLAN_LOOKUP] = { + .entry_packing = sja1105_vlan_lookup_entry_packing, + .cmd_packing = sja1105_vlan_lookup_cmd_packing, + .access = (OP_WRITE | OP_DEL), + .max_entry_count = SJA1105_MAX_VLAN_LOOKUP_COUNT, + .packed_size = SJA1105_SIZE_VLAN_LOOKUP_DYN_CMD, + .addr = 0x27, + }, + [BLK_IDX_L2_FORWARDING] = { + .entry_packing = sja1105_l2_forwarding_entry_packing, + .cmd_packing = sja1105_l2_forwarding_cmd_packing, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_COUNT, + .access = OP_WRITE, + .packed_size = SJA1105_SIZE_L2_FORWARDING_DYN_CMD, + .addr = 0x24, + }, + [BLK_IDX_MAC_CONFIG] = { + .entry_packing = sja1105et_mac_config_entry_packing, + .cmd_packing = sja1105et_mac_config_cmd_packing, + .max_entry_count = SJA1105_MAX_MAC_CONFIG_COUNT, + .access = OP_WRITE, + .packed_size = SJA1105ET_SIZE_MAC_CONFIG_DYN_CMD, + .addr = 0x36, + }, + [BLK_IDX_L2_LOOKUP_PARAMS] = { + .entry_packing = sja1105et_l2_lookup_params_entry_packing, + .cmd_packing = sja1105et_l2_lookup_params_cmd_packing, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, + .access = OP_WRITE, + .packed_size = SJA1105ET_SIZE_L2_LOOKUP_PARAMS_DYN_CMD, + .addr = 0x38, + }, + [BLK_IDX_L2_FORWARDING_PARAMS] = {0}, + [BLK_IDX_GENERAL_PARAMS] = { + .entry_packing = sja1105et_general_params_entry_packing, + .cmd_packing = sja1105et_general_params_cmd_packing, + .max_entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT, + .access = OP_WRITE, + .packed_size = SJA1105ET_SIZE_GENERAL_PARAMS_DYN_CMD, + .addr = 0x34, + }, + [BLK_IDX_XMII_PARAMS] = {0}, +}; + +/* SJA1105P/Q/R/S: Second generation: TODO */ +struct sja1105_dynamic_table_ops sja1105pqrs_dyn_ops[BLK_IDX_MAX_DYN] = { + [BLK_IDX_L2_LOOKUP] = { + .entry_packing = sja1105pqrs_l2_lookup_entry_packing, + .cmd_packing = sja1105pqrs_l2_lookup_cmd_packing, + .access = (OP_READ | OP_WRITE | OP_DEL), + .max_entry_count = SJA1105_MAX_L2_LOOKUP_COUNT, + .packed_size = SJA1105ET_SIZE_L2_LOOKUP_DYN_CMD, + .addr = 0x24, + }, + [BLK_IDX_L2_POLICING] = {0}, + [BLK_IDX_VLAN_LOOKUP] = { + .entry_packing = sja1105_vlan_lookup_entry_packing, + .cmd_packing = sja1105_vlan_lookup_cmd_packing, + .access = (OP_READ | OP_WRITE | OP_DEL), + .max_entry_count = SJA1105_MAX_VLAN_LOOKUP_COUNT, + .packed_size = SJA1105_SIZE_VLAN_LOOKUP_DYN_CMD, + .addr = 0x2D, + }, + [BLK_IDX_L2_FORWARDING] = { + .entry_packing = sja1105_l2_forwarding_entry_packing, + .cmd_packing = sja1105_l2_forwarding_cmd_packing, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_COUNT, + .access = OP_WRITE, + .packed_size = SJA1105_SIZE_L2_FORWARDING_DYN_CMD, + .addr = 0x2A, + }, + [BLK_IDX_MAC_CONFIG] = { + .entry_packing = sja1105pqrs_mac_config_entry_packing, + .cmd_packing = sja1105pqrs_mac_config_cmd_packing, + .max_entry_count = SJA1105_MAX_MAC_CONFIG_COUNT, + .access = (OP_READ | OP_WRITE), + .packed_size = SJA1105PQRS_SIZE_MAC_CONFIG_DYN_CMD, + .addr = 0x4B, + }, + [BLK_IDX_L2_LOOKUP_PARAMS] = { + .entry_packing = sja1105et_l2_lookup_params_entry_packing, + .cmd_packing = sja1105et_l2_lookup_params_cmd_packing, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, + .access = (OP_READ | OP_WRITE), + .packed_size = SJA1105ET_SIZE_L2_LOOKUP_PARAMS_DYN_CMD, + .addr = 0x38, + }, + [BLK_IDX_L2_FORWARDING_PARAMS] = {0}, + [BLK_IDX_GENERAL_PARAMS] = { + .entry_packing = sja1105et_general_params_entry_packing, + .cmd_packing = sja1105et_general_params_cmd_packing, + .max_entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT, + .access = OP_WRITE, + .packed_size = SJA1105ET_SIZE_GENERAL_PARAMS_DYN_CMD, + .addr = 0x34, + }, + [BLK_IDX_XMII_PARAMS] = {0}, +}; + +int sja1105_dynamic_config_read(struct sja1105_private *priv, + enum sja1105_blk_idx blk_idx, + int index, void *entry) +{ + const struct sja1105_dynamic_table_ops *ops; + struct sja1105_dyn_cmd cmd = {0}; + /* SPI payload buffer */ + u8 packed_buf[SJA1105_MAX_DYN_CMD_SIZE] = {0}; + int retries = 3; + int rc; + + if (blk_idx >= BLK_IDX_MAX_DYN) + return -ERANGE; + + ops = &priv->info->dyn_ops[blk_idx]; + + if (index >= ops->max_entry_count) + return -ERANGE; + if (!(ops->access & OP_READ)) + return -EOPNOTSUPP; + if (ops->packed_size > SJA1105_MAX_DYN_CMD_SIZE) + return -ERANGE; + if (!ops->cmd_packing) + return -EOPNOTSUPP; + if (!ops->entry_packing) + return -EOPNOTSUPP; + + cmd.valid = true; /* Trigger action on table entry */ + cmd.rdwrset = SPI_READ; /* Action is read */ + cmd.index = index; + ops->cmd_packing(packed_buf, &cmd, PACK); + + /* Send SPI write operation: read config table entry */ + rc = sja1105_spi_send_packed_buf(priv, SPI_WRITE, ops->addr, + packed_buf, ops->packed_size); + if (rc < 0) + return rc; + + /* Loop until we have confirmation that hardware has finished + * processing the command and has cleared the VALID field + */ + do { + memset(packed_buf, 0, ops->packed_size); + + /* Retrieve the read operation's result */ + rc = sja1105_spi_send_packed_buf(priv, SPI_READ, ops->addr, + packed_buf, ops->packed_size); + if (rc < 0) + return rc; + + cmd = (struct sja1105_dyn_cmd) {0}; + ops->cmd_packing(packed_buf, &cmd, UNPACK); + /* UM10944: [valident] will always be found cleared + * during a read access with MGMTROUTE set. + * So don't error out in that case. + */ + if (!cmd.valident && blk_idx != BLK_IDX_MGMT_ROUTE) + return -EINVAL; + cpu_relax(); + } while (cmd.valid && --retries); + + if (cmd.valid) + return -ETIMEDOUT; + + /* Don't dereference possibly NULL pointer - maybe caller + * only wanted to see whether the entry existed or not. + */ + if (entry) + ops->entry_packing(packed_buf, entry, UNPACK); + return 0; +} + +int sja1105_dynamic_config_write(struct sja1105_private *priv, + enum sja1105_blk_idx blk_idx, + int index, void *entry, bool keep) +{ + const struct sja1105_dynamic_table_ops *ops; + struct sja1105_dyn_cmd cmd = {0}; + /* SPI payload buffer */ + u8 packed_buf[SJA1105_MAX_DYN_CMD_SIZE] = {0}; + int rc; + + if (blk_idx >= BLK_IDX_MAX_DYN) + return -ERANGE; + + ops = &priv->info->dyn_ops[blk_idx]; + + if (index >= ops->max_entry_count) + return -ERANGE; + if (!(ops->access & OP_WRITE)) + return -EOPNOTSUPP; + if (!keep && !(ops->access & OP_DEL)) + return -EOPNOTSUPP; + if (ops->packed_size > SJA1105_MAX_DYN_CMD_SIZE) + return -ERANGE; + + cmd.valident = keep; /* If false, deletes entry */ + cmd.valid = true; /* Trigger action on table entry */ + cmd.rdwrset = SPI_WRITE; /* Action is write */ + cmd.index = index; + + if (!ops->cmd_packing) + return -EOPNOTSUPP; + ops->cmd_packing(packed_buf, &cmd, PACK); + + if (!ops->entry_packing) + return -EOPNOTSUPP; + /* Don't dereference potentially NULL pointer if just + * deleting a table entry is what was requested. For cases + * where 'index' field is physically part of entry structure, + * and needed here, we deal with that in the cmd_packing callback. + */ + if (keep) + ops->entry_packing(packed_buf, entry, PACK); + + /* Send SPI write operation: read config table entry */ + rc = sja1105_spi_send_packed_buf(priv, SPI_WRITE, ops->addr, + packed_buf, ops->packed_size); + if (rc < 0) + return rc; + + cmd = (struct sja1105_dyn_cmd) {0}; + ops->cmd_packing(packed_buf, &cmd, UNPACK); + if (cmd.errors) + return -EINVAL; + + return 0; +} + +static u8 sja1105_crc8_add(u8 crc, u8 byte, u8 poly) +{ + int i; + + for (i = 0; i < 8; i++) { + if ((crc ^ byte) & (1 << 7)) { + crc <<= 1; + crc ^= poly; + } else { + crc <<= 1; + } + byte <<= 1; + } + return crc; +} + +/* CRC8 algorithm with non-reversed input, non-reversed output, + * no input xor and no output xor. Code customized for receiving + * the SJA1105 E/T FDB keys (vlanid, macaddr) as input. CRC polynomial + * is also received as argument in the Koopman notation that the switch + * hardware stores it in. + */ +u8 sja1105_fdb_hash(struct sja1105_private *priv, const u8 *addr, u16 vid) +{ + struct sja1105_l2_lookup_params_entry *l2_lookup_params = + priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS].entries; + u64 poly_koopman = l2_lookup_params->poly; + /* Convert polynomial from Koopman to 'normal' notation */ + u8 poly = (u8)(1 + (poly_koopman << 1)); + u64 vlanid = l2_lookup_params->shared_learn ? 0 : vid; + u64 input = (vlanid << 48) | ether_addr_to_u64(addr); + u8 crc = 0; /* seed */ + int i; + + /* Mask the eight bytes starting from MSB one at a time */ + for (i = 56; i >= 0; i -= 8) { + u8 byte = (input & (0xffull << i)) >> i; + + crc = sja1105_crc8_add(crc, byte, poly); + } + return crc; +} diff --git a/drivers/net/dsa/sja1105/sja1105_dynamic_config.h b/drivers/net/dsa/sja1105/sja1105_dynamic_config.h new file mode 100644 index 000000000000..77be59546a55 --- /dev/null +++ b/drivers/net/dsa/sja1105/sja1105_dynamic_config.h @@ -0,0 +1,43 @@ +/* SPDX-License-Identifier: GPL-2.0 + * Copyright (c) 2019, Vladimir Oltean <olteanv@gmail.com> + */ +#ifndef _SJA1105_DYNAMIC_CONFIG_H +#define _SJA1105_DYNAMIC_CONFIG_H + +#include "sja1105.h" +#include <linux/packing.h> + +struct sja1105_dyn_cmd { + u64 valid; + u64 rdwrset; + u64 errors; + u64 valident; + u64 index; +}; + +struct sja1105_dynamic_table_ops { + /* This returns size_t just to keep same prototype as the + * static config ops, of which we are reusing some functions. + */ + size_t (*entry_packing)(void *buf, void *entry_ptr, enum packing_op op); + void (*cmd_packing)(void *buf, struct sja1105_dyn_cmd *cmd, + enum packing_op op); + size_t max_entry_count; + size_t packed_size; + u64 addr; + u8 access; +}; + +struct sja1105_mgmt_entry { + u64 tsreg; + u64 takets; + u64 macaddr; + u64 destports; + u64 enfport; + u64 index; +}; + +extern struct sja1105_dynamic_table_ops sja1105et_dyn_ops[BLK_IDX_MAX_DYN]; +extern struct sja1105_dynamic_table_ops sja1105pqrs_dyn_ops[BLK_IDX_MAX_DYN]; + +#endif diff --git a/drivers/net/dsa/sja1105/sja1105_ethtool.c b/drivers/net/dsa/sja1105/sja1105_ethtool.c new file mode 100644 index 000000000000..46d22be31309 --- /dev/null +++ b/drivers/net/dsa/sja1105/sja1105_ethtool.c @@ -0,0 +1,417 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ +#include "sja1105.h" + +#define SJA1105_SIZE_MAC_AREA (0x02 * 4) +#define SJA1105_SIZE_HL1_AREA (0x10 * 4) +#define SJA1105_SIZE_HL2_AREA (0x4 * 4) +#define SJA1105_SIZE_QLEVEL_AREA (0x8 * 4) /* 0x4 to 0xB */ + +struct sja1105_port_status_mac { + u64 n_runt; + u64 n_soferr; + u64 n_alignerr; + u64 n_miierr; + u64 typeerr; + u64 sizeerr; + u64 tctimeout; + u64 priorerr; + u64 nomaster; + u64 memov; + u64 memerr; + u64 invtyp; + u64 intcyov; + u64 domerr; + u64 pcfbagdrop; + u64 spcprior; + u64 ageprior; + u64 portdrop; + u64 lendrop; + u64 bagdrop; + u64 policeerr; + u64 drpnona664err; + u64 spcerr; + u64 agedrp; +}; + +struct sja1105_port_status_hl1 { + u64 n_n664err; + u64 n_vlanerr; + u64 n_unreleased; + u64 n_sizeerr; + u64 n_crcerr; + u64 n_vlnotfound; + u64 n_ctpolerr; + u64 n_polerr; + u64 n_rxfrmsh; + u64 n_rxfrm; + u64 n_rxbytesh; + u64 n_rxbyte; + u64 n_txfrmsh; + u64 n_txfrm; + u64 n_txbytesh; + u64 n_txbyte; +}; + +struct sja1105_port_status_hl2 { + u64 n_qfull; + u64 n_part_drop; + u64 n_egr_disabled; + u64 n_not_reach; + u64 qlevel_hwm[8]; /* Only for P/Q/R/S */ + u64 qlevel[8]; /* Only for P/Q/R/S */ +}; + +struct sja1105_port_status { + struct sja1105_port_status_mac mac; + struct sja1105_port_status_hl1 hl1; + struct sja1105_port_status_hl2 hl2; +}; + +static void +sja1105_port_status_mac_unpack(void *buf, + struct sja1105_port_status_mac *status) +{ + /* Make pointer arithmetic work on 4 bytes */ + u32 *p = buf; + + sja1105_unpack(p + 0x0, &status->n_runt, 31, 24, 4); + sja1105_unpack(p + 0x0, &status->n_soferr, 23, 16, 4); + sja1105_unpack(p + 0x0, &status->n_alignerr, 15, 8, 4); + sja1105_unpack(p + 0x0, &status->n_miierr, 7, 0, 4); + sja1105_unpack(p + 0x1, &status->typeerr, 27, 27, 4); + sja1105_unpack(p + 0x1, &status->sizeerr, 26, 26, 4); + sja1105_unpack(p + 0x1, &status->tctimeout, 25, 25, 4); + sja1105_unpack(p + 0x1, &status->priorerr, 24, 24, 4); + sja1105_unpack(p + 0x1, &status->nomaster, 23, 23, 4); + sja1105_unpack(p + 0x1, &status->memov, 22, 22, 4); + sja1105_unpack(p + 0x1, &status->memerr, 21, 21, 4); + sja1105_unpack(p + 0x1, &status->invtyp, 19, 19, 4); + sja1105_unpack(p + 0x1, &status->intcyov, 18, 18, 4); + sja1105_unpack(p + 0x1, &status->domerr, 17, 17, 4); + sja1105_unpack(p + 0x1, &status->pcfbagdrop, 16, 16, 4); + sja1105_unpack(p + 0x1, &status->spcprior, 15, 12, 4); + sja1105_unpack(p + 0x1, &status->ageprior, 11, 8, 4); + sja1105_unpack(p + 0x1, &status->portdrop, 6, 6, 4); + sja1105_unpack(p + 0x1, &status->lendrop, 5, 5, 4); + sja1105_unpack(p + 0x1, &status->bagdrop, 4, 4, 4); + sja1105_unpack(p + 0x1, &status->policeerr, 3, 3, 4); + sja1105_unpack(p + 0x1, &status->drpnona664err, 2, 2, 4); + sja1105_unpack(p + 0x1, &status->spcerr, 1, 1, 4); + sja1105_unpack(p + 0x1, &status->agedrp, 0, 0, 4); +} + +static void +sja1105_port_status_hl1_unpack(void *buf, + struct sja1105_port_status_hl1 *status) +{ + /* Make pointer arithmetic work on 4 bytes */ + u32 *p = buf; + + sja1105_unpack(p + 0xF, &status->n_n664err, 31, 0, 4); + sja1105_unpack(p + 0xE, &status->n_vlanerr, 31, 0, 4); + sja1105_unpack(p + 0xD, &status->n_unreleased, 31, 0, 4); + sja1105_unpack(p + 0xC, &status->n_sizeerr, 31, 0, 4); + sja1105_unpack(p + 0xB, &status->n_crcerr, 31, 0, 4); + sja1105_unpack(p + 0xA, &status->n_vlnotfound, 31, 0, 4); + sja1105_unpack(p + 0x9, &status->n_ctpolerr, 31, 0, 4); + sja1105_unpack(p + 0x8, &status->n_polerr, 31, 0, 4); + sja1105_unpack(p + 0x7, &status->n_rxfrmsh, 31, 0, 4); + sja1105_unpack(p + 0x6, &status->n_rxfrm, 31, 0, 4); + sja1105_unpack(p + 0x5, &status->n_rxbytesh, 31, 0, 4); + sja1105_unpack(p + 0x4, &status->n_rxbyte, 31, 0, 4); + sja1105_unpack(p + 0x3, &status->n_txfrmsh, 31, 0, 4); + sja1105_unpack(p + 0x2, &status->n_txfrm, 31, 0, 4); + sja1105_unpack(p + 0x1, &status->n_txbytesh, 31, 0, 4); + sja1105_unpack(p + 0x0, &status->n_txbyte, 31, 0, 4); + status->n_rxfrm += status->n_rxfrmsh << 32; + status->n_rxbyte += status->n_rxbytesh << 32; + status->n_txfrm += status->n_txfrmsh << 32; + status->n_txbyte += status->n_txbytesh << 32; +} + +static void +sja1105_port_status_hl2_unpack(void *buf, + struct sja1105_port_status_hl2 *status) +{ + /* Make pointer arithmetic work on 4 bytes */ + u32 *p = buf; + + sja1105_unpack(p + 0x3, &status->n_qfull, 31, 0, 4); + sja1105_unpack(p + 0x2, &status->n_part_drop, 31, 0, 4); + sja1105_unpack(p + 0x1, &status->n_egr_disabled, 31, 0, 4); + sja1105_unpack(p + 0x0, &status->n_not_reach, 31, 0, 4); +} + +static void +sja1105pqrs_port_status_qlevel_unpack(void *buf, + struct sja1105_port_status_hl2 *status) +{ + /* Make pointer arithmetic work on 4 bytes */ + u32 *p = buf; + int i; + + for (i = 0; i < 8; i++) { + sja1105_unpack(p + i, &status->qlevel_hwm[i], 24, 16, 4); + sja1105_unpack(p + i, &status->qlevel[i], 8, 0, 4); + } +} + +static int sja1105_port_status_get_mac(struct sja1105_private *priv, + struct sja1105_port_status_mac *status, + int port) +{ + const struct sja1105_regs *regs = priv->info->regs; + u8 packed_buf[SJA1105_SIZE_MAC_AREA] = {0}; + int rc; + + /* MAC area */ + rc = sja1105_spi_send_packed_buf(priv, SPI_READ, regs->mac[port], + packed_buf, SJA1105_SIZE_MAC_AREA); + if (rc < 0) + return rc; + + sja1105_port_status_mac_unpack(packed_buf, status); + + return 0; +} + +static int sja1105_port_status_get_hl1(struct sja1105_private *priv, + struct sja1105_port_status_hl1 *status, + int port) +{ + const struct sja1105_regs *regs = priv->info->regs; + u8 packed_buf[SJA1105_SIZE_HL1_AREA] = {0}; + int rc; + + rc = sja1105_spi_send_packed_buf(priv, SPI_READ, regs->mac_hl1[port], + packed_buf, SJA1105_SIZE_HL1_AREA); + if (rc < 0) + return rc; + + sja1105_port_status_hl1_unpack(packed_buf, status); + + return 0; +} + +static int sja1105_port_status_get_hl2(struct sja1105_private *priv, + struct sja1105_port_status_hl2 *status, + int port) +{ + const struct sja1105_regs *regs = priv->info->regs; + u8 packed_buf[SJA1105_SIZE_QLEVEL_AREA] = {0}; + int rc; + + rc = sja1105_spi_send_packed_buf(priv, SPI_READ, regs->mac_hl2[port], + packed_buf, SJA1105_SIZE_HL2_AREA); + if (rc < 0) + return rc; + + sja1105_port_status_hl2_unpack(packed_buf, status); + + /* Code below is strictly P/Q/R/S specific. */ + if (priv->info->device_id == SJA1105E_DEVICE_ID || + priv->info->device_id == SJA1105T_DEVICE_ID) + return 0; + + rc = sja1105_spi_send_packed_buf(priv, SPI_READ, regs->qlevel[port], + packed_buf, SJA1105_SIZE_QLEVEL_AREA); + if (rc < 0) + return rc; + + sja1105pqrs_port_status_qlevel_unpack(packed_buf, status); + + return 0; +} + +static int sja1105_port_status_get(struct sja1105_private *priv, + struct sja1105_port_status *status, + int port) +{ + int rc; + + rc = sja1105_port_status_get_mac(priv, &status->mac, port); + if (rc < 0) + return rc; + rc = sja1105_port_status_get_hl1(priv, &status->hl1, port); + if (rc < 0) + return rc; + rc = sja1105_port_status_get_hl2(priv, &status->hl2, port); + if (rc < 0) + return rc; + + return 0; +} + +static char sja1105_port_stats[][ETH_GSTRING_LEN] = { + /* MAC-Level Diagnostic Counters */ + "n_runt", + "n_soferr", + "n_alignerr", + "n_miierr", + /* MAC-Level Diagnostic Flags */ + "typeerr", + "sizeerr", + "tctimeout", + "priorerr", + "nomaster", + "memov", + "memerr", + "invtyp", + "intcyov", + "domerr", + "pcfbagdrop", + "spcprior", + "ageprior", + "portdrop", + "lendrop", + "bagdrop", + "policeerr", + "drpnona664err", + "spcerr", + "agedrp", + /* High-Level Diagnostic Counters */ + "n_n664err", + "n_vlanerr", + "n_unreleased", + "n_sizeerr", + "n_crcerr", + "n_vlnotfound", + "n_ctpolerr", + "n_polerr", + "n_rxfrm", + "n_rxbyte", + "n_txfrm", + "n_txbyte", + "n_qfull", + "n_part_drop", + "n_egr_disabled", + "n_not_reach", +}; + +static char sja1105pqrs_extra_port_stats[][ETH_GSTRING_LEN] = { + /* Queue Levels */ + "qlevel_hwm_0", + "qlevel_hwm_1", + "qlevel_hwm_2", + "qlevel_hwm_3", + "qlevel_hwm_4", + "qlevel_hwm_5", + "qlevel_hwm_6", + "qlevel_hwm_7", + "qlevel_0", + "qlevel_1", + "qlevel_2", + "qlevel_3", + "qlevel_4", + "qlevel_5", + "qlevel_6", + "qlevel_7", +}; + +void sja1105_get_ethtool_stats(struct dsa_switch *ds, int port, u64 *data) +{ + struct sja1105_private *priv = ds->priv; + struct sja1105_port_status status = {0}; + int rc, i, k = 0; + + rc = sja1105_port_status_get(priv, &status, port); + if (rc < 0) { + dev_err(ds->dev, "Failed to read port %d counters: %d\n", + port, rc); + return; + } + memset(data, 0, ARRAY_SIZE(sja1105_port_stats) * sizeof(u64)); + data[k++] = status.mac.n_runt; + data[k++] = status.mac.n_soferr; + data[k++] = status.mac.n_alignerr; + data[k++] = status.mac.n_miierr; + data[k++] = status.mac.typeerr; + data[k++] = status.mac.sizeerr; + data[k++] = status.mac.tctimeout; + data[k++] = status.mac.priorerr; + data[k++] = status.mac.nomaster; + data[k++] = status.mac.memov; + data[k++] = status.mac.memerr; + data[k++] = status.mac.invtyp; + data[k++] = status.mac.intcyov; + data[k++] = status.mac.domerr; + data[k++] = status.mac.pcfbagdrop; + data[k++] = status.mac.spcprior; + data[k++] = status.mac.ageprior; + data[k++] = status.mac.portdrop; + data[k++] = status.mac.lendrop; + data[k++] = status.mac.bagdrop; + data[k++] = status.mac.policeerr; + data[k++] = status.mac.drpnona664err; + data[k++] = status.mac.spcerr; + data[k++] = status.mac.agedrp; + data[k++] = status.hl1.n_n664err; + data[k++] = status.hl1.n_vlanerr; + data[k++] = status.hl1.n_unreleased; + data[k++] = status.hl1.n_sizeerr; + data[k++] = status.hl1.n_crcerr; + data[k++] = status.hl1.n_vlnotfound; + data[k++] = status.hl1.n_ctpolerr; + data[k++] = status.hl1.n_polerr; + data[k++] = status.hl1.n_rxfrm; + data[k++] = status.hl1.n_rxbyte; + data[k++] = status.hl1.n_txfrm; + data[k++] = status.hl1.n_txbyte; + data[k++] = status.hl2.n_qfull; + data[k++] = status.hl2.n_part_drop; + data[k++] = status.hl2.n_egr_disabled; + data[k++] = status.hl2.n_not_reach; + + if (priv->info->device_id == SJA1105E_DEVICE_ID || + priv->info->device_id == SJA1105T_DEVICE_ID) + return; + + memset(data + k, 0, ARRAY_SIZE(sja1105pqrs_extra_port_stats) * + sizeof(u64)); + for (i = 0; i < 8; i++) { + data[k++] = status.hl2.qlevel_hwm[i]; + data[k++] = status.hl2.qlevel[i]; + } +} + +void sja1105_get_strings(struct dsa_switch *ds, int port, + u32 stringset, u8 *data) +{ + struct sja1105_private *priv = ds->priv; + u8 *p = data; + int i; + + switch (stringset) { + case ETH_SS_STATS: + for (i = 0; i < ARRAY_SIZE(sja1105_port_stats); i++) { + strlcpy(p, sja1105_port_stats[i], ETH_GSTRING_LEN); + p += ETH_GSTRING_LEN; + } + if (priv->info->device_id == SJA1105E_DEVICE_ID || + priv->info->device_id == SJA1105T_DEVICE_ID) + return; + for (i = 0; i < ARRAY_SIZE(sja1105pqrs_extra_port_stats); i++) { + strlcpy(p, sja1105pqrs_extra_port_stats[i], + ETH_GSTRING_LEN); + p += ETH_GSTRING_LEN; + } + break; + } +} + +int sja1105_get_sset_count(struct dsa_switch *ds, int port, int sset) +{ + int count = ARRAY_SIZE(sja1105_port_stats); + struct sja1105_private *priv = ds->priv; + + if (sset != ETH_SS_STATS) + return -EOPNOTSUPP; + + if (priv->info->device_id == SJA1105PR_DEVICE_ID || + priv->info->device_id == SJA1105QS_DEVICE_ID) + count += ARRAY_SIZE(sja1105pqrs_extra_port_stats); + + return count; +} diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c new file mode 100644 index 000000000000..74f8ff9e17e0 --- /dev/null +++ b/drivers/net/dsa/sja1105/sja1105_main.c @@ -0,0 +1,1459 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2018, Sensor-Technik Wiedemann GmbH + * Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/printk.h> +#include <linux/spi/spi.h> +#include <linux/errno.h> +#include <linux/gpio/consumer.h> +#include <linux/phylink.h> +#include <linux/of.h> +#include <linux/of_net.h> +#include <linux/of_mdio.h> +#include <linux/of_device.h> +#include <linux/netdev_features.h> +#include <linux/netdevice.h> +#include <linux/if_bridge.h> +#include <linux/if_ether.h> +#include "sja1105.h" + +static void sja1105_hw_reset(struct gpio_desc *gpio, unsigned int pulse_len, + unsigned int startup_delay) +{ + gpiod_set_value_cansleep(gpio, 1); + /* Wait for minimum reset pulse length */ + msleep(pulse_len); + gpiod_set_value_cansleep(gpio, 0); + /* Wait until chip is ready after reset */ + msleep(startup_delay); +} + +static void +sja1105_port_allow_traffic(struct sja1105_l2_forwarding_entry *l2_fwd, + int from, int to, bool allow) +{ + if (allow) { + l2_fwd[from].bc_domain |= BIT(to); + l2_fwd[from].reach_port |= BIT(to); + l2_fwd[from].fl_domain |= BIT(to); + } else { + l2_fwd[from].bc_domain &= ~BIT(to); + l2_fwd[from].reach_port &= ~BIT(to); + l2_fwd[from].fl_domain &= ~BIT(to); + } +} + +/* Structure used to temporarily transport device tree + * settings into sja1105_setup + */ +struct sja1105_dt_port { + phy_interface_t phy_mode; + sja1105_mii_role_t role; +}; + +static int sja1105_init_mac_settings(struct sja1105_private *priv) +{ + struct sja1105_mac_config_entry default_mac = { + /* Enable all 8 priority queues on egress. + * Every queue i holds top[i] - base[i] frames. + * Sum of top[i] - base[i] is 511 (max hardware limit). + */ + .top = {0x3F, 0x7F, 0xBF, 0xFF, 0x13F, 0x17F, 0x1BF, 0x1FF}, + .base = {0x0, 0x40, 0x80, 0xC0, 0x100, 0x140, 0x180, 0x1C0}, + .enabled = {true, true, true, true, true, true, true, true}, + /* Keep standard IFG of 12 bytes on egress. */ + .ifg = 0, + /* Always put the MAC speed in automatic mode, where it can be + * retrieved from the PHY object through phylib and + * sja1105_adjust_port_config. + */ + .speed = SJA1105_SPEED_AUTO, + /* No static correction for 1-step 1588 events */ + .tp_delin = 0, + .tp_delout = 0, + /* Disable aging for critical TTEthernet traffic */ + .maxage = 0xFF, + /* Internal VLAN (pvid) to apply to untagged ingress */ + .vlanprio = 0, + .vlanid = 0, + .ing_mirr = false, + .egr_mirr = false, + /* Don't drop traffic with other EtherType than ETH_P_IP */ + .drpnona664 = false, + /* Don't drop double-tagged traffic */ + .drpdtag = false, + /* Don't drop untagged traffic */ + .drpuntag = false, + /* Don't retag 802.1p (VID 0) traffic with the pvid */ + .retag = false, + /* Enable learning and I/O on user ports by default. */ + .dyn_learn = true, + .egress = false, + .ingress = false, + }; + struct sja1105_mac_config_entry *mac; + struct sja1105_table *table; + int i; + + table = &priv->static_config.tables[BLK_IDX_MAC_CONFIG]; + + /* Discard previous MAC Configuration Table */ + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_NUM_PORTS, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + /* Override table based on phylib DT bindings */ + table->entry_count = SJA1105_NUM_PORTS; + + mac = table->entries; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) + mac[i] = default_mac; + + return 0; +} + +static int sja1105_init_mii_settings(struct sja1105_private *priv, + struct sja1105_dt_port *ports) +{ + struct device *dev = &priv->spidev->dev; + struct sja1105_xmii_params_entry *mii; + struct sja1105_table *table; + int i; + + table = &priv->static_config.tables[BLK_IDX_XMII_PARAMS]; + + /* Discard previous xMII Mode Parameters Table */ + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_XMII_PARAMS_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + /* Override table based on phylib DT bindings */ + table->entry_count = SJA1105_MAX_XMII_PARAMS_COUNT; + + mii = table->entries; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + switch (ports[i].phy_mode) { + case PHY_INTERFACE_MODE_MII: + mii->xmii_mode[i] = XMII_MODE_MII; + break; + case PHY_INTERFACE_MODE_RMII: + mii->xmii_mode[i] = XMII_MODE_RMII; + break; + case PHY_INTERFACE_MODE_RGMII: + case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII_RXID: + case PHY_INTERFACE_MODE_RGMII_TXID: + mii->xmii_mode[i] = XMII_MODE_RGMII; + break; + default: + dev_err(dev, "Unsupported PHY mode %s!\n", + phy_modes(ports[i].phy_mode)); + } + + mii->phy_mac[i] = ports[i].role; + } + return 0; +} + +static int sja1105_init_static_fdb(struct sja1105_private *priv) +{ + struct sja1105_table *table; + + table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP]; + + /* We only populate the FDB table through dynamic + * L2 Address Lookup entries + */ + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + return 0; +} + +static int sja1105_init_l2_lookup_params(struct sja1105_private *priv) +{ + struct sja1105_table *table; + struct sja1105_l2_lookup_params_entry default_l2_lookup_params = { + /* Learned FDB entries are forgotten after 300 seconds */ + .maxage = SJA1105_AGEING_TIME_MS(300000), + /* All entries within a FDB bin are available for learning */ + .dyn_tbsz = SJA1105ET_FDB_BIN_SIZE, + /* 2^8 + 2^5 + 2^3 + 2^2 + 2^1 + 1 in Koopman notation */ + .poly = 0x97, + /* This selects between Independent VLAN Learning (IVL) and + * Shared VLAN Learning (SVL) + */ + .shared_learn = false, + /* Don't discard management traffic based on ENFPORT - + * we don't perform SMAC port enforcement anyway, so + * what we are setting here doesn't matter. + */ + .no_enf_hostprt = false, + /* Don't learn SMAC for mac_fltres1 and mac_fltres0. + * Maybe correlate with no_linklocal_learn from bridge driver? + */ + .no_mgmt_learn = true, + }; + + table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS]; + + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT; + + /* This table only has a single entry */ + ((struct sja1105_l2_lookup_params_entry *)table->entries)[0] = + default_l2_lookup_params; + + return 0; +} + +static int sja1105_init_static_vlan(struct sja1105_private *priv) +{ + struct sja1105_table *table; + struct sja1105_vlan_lookup_entry pvid = { + .ving_mirr = 0, + .vegr_mirr = 0, + .vmemb_port = 0, + .vlan_bc = 0, + .tag_port = 0, + .vlanid = 0, + }; + int i; + + table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP]; + + /* The static VLAN table will only contain the initial pvid of 0. + * All other VLANs are to be configured through dynamic entries, + * and kept in the static configuration table as backing memory. + * The pvid of 0 is sufficient to pass traffic while the ports are + * standalone and when vlan_filtering is disabled. When filtering + * gets enabled, the switchdev core sets up the VLAN ID 1 and sets + * it as the new pvid. Actually 'pvid 1' still comes up in 'bridge + * vlan' even when vlan_filtering is off, but it has no effect. + */ + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(1, table->ops->unpacked_entry_size, + GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = 1; + + /* VLAN ID 0: all DT-defined ports are members; no restrictions on + * forwarding; always transmit priority-tagged frames as untagged. + */ + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + pvid.vmemb_port |= BIT(i); + pvid.vlan_bc |= BIT(i); + pvid.tag_port &= ~BIT(i); + } + + ((struct sja1105_vlan_lookup_entry *)table->entries)[0] = pvid; + return 0; +} + +static int sja1105_init_l2_forwarding(struct sja1105_private *priv) +{ + struct sja1105_l2_forwarding_entry *l2fwd; + struct sja1105_table *table; + int i, j; + + table = &priv->static_config.tables[BLK_IDX_L2_FORWARDING]; + + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_L2_FORWARDING_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = SJA1105_MAX_L2_FORWARDING_COUNT; + + l2fwd = table->entries; + + /* First 5 entries define the forwarding rules */ + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + unsigned int upstream = dsa_upstream_port(priv->ds, i); + + for (j = 0; j < SJA1105_NUM_TC; j++) + l2fwd[i].vlan_pmap[j] = j; + + if (i == upstream) + continue; + + sja1105_port_allow_traffic(l2fwd, i, upstream, true); + sja1105_port_allow_traffic(l2fwd, upstream, i, true); + } + /* Next 8 entries define VLAN PCP mapping from ingress to egress. + * Create a one-to-one mapping. + */ + for (i = 0; i < SJA1105_NUM_TC; i++) + for (j = 0; j < SJA1105_NUM_PORTS; j++) + l2fwd[SJA1105_NUM_PORTS + i].vlan_pmap[j] = i; + + return 0; +} + +static int sja1105_init_l2_forwarding_params(struct sja1105_private *priv) +{ + struct sja1105_l2_forwarding_params_entry default_l2fwd_params = { + /* Disallow dynamic reconfiguration of vlan_pmap */ + .max_dynp = 0, + /* Use a single memory partition for all ingress queues */ + .part_spc = { SJA1105_MAX_FRAME_MEMORY, 0, 0, 0, 0, 0, 0, 0 }, + }; + struct sja1105_table *table; + + table = &priv->static_config.tables[BLK_IDX_L2_FORWARDING_PARAMS]; + + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT; + + /* This table only has a single entry */ + ((struct sja1105_l2_forwarding_params_entry *)table->entries)[0] = + default_l2fwd_params; + + return 0; +} + +static int sja1105_init_general_params(struct sja1105_private *priv) +{ + struct sja1105_general_params_entry default_general_params = { + /* Disallow dynamic changing of the mirror port */ + .mirr_ptacu = 0, + .switchid = priv->ds->index, + /* Priority queue for link-local frames trapped to CPU */ + .hostprio = 0, + .mac_fltres1 = SJA1105_LINKLOCAL_FILTER_A, + .mac_flt1 = SJA1105_LINKLOCAL_FILTER_A_MASK, + .incl_srcpt1 = true, + .send_meta1 = false, + .mac_fltres0 = SJA1105_LINKLOCAL_FILTER_B, + .mac_flt0 = SJA1105_LINKLOCAL_FILTER_B_MASK, + .incl_srcpt0 = true, + .send_meta0 = false, + /* The destination for traffic matching mac_fltres1 and + * mac_fltres0 on all ports except host_port. Such traffic + * receieved on host_port itself would be dropped, except + * by installing a temporary 'management route' + */ + .host_port = dsa_upstream_port(priv->ds, 0), + /* Same as host port */ + .mirr_port = dsa_upstream_port(priv->ds, 0), + /* Link-local traffic received on casc_port will be forwarded + * to host_port without embedding the source port and device ID + * info in the destination MAC address (presumably because it + * is a cascaded port and a downstream SJA switch already did + * that). Default to an invalid port (to disable the feature) + * and overwrite this if we find any DSA (cascaded) ports. + */ + .casc_port = SJA1105_NUM_PORTS, + /* No TTEthernet */ + .vllupformat = 0, + .vlmarker = 0, + .vlmask = 0, + /* Only update correctionField for 1-step PTP (L2 transport) */ + .ignore2stf = 0, + /* Forcefully disable VLAN filtering by telling + * the switch that VLAN has a different EtherType. + */ + .tpid = ETH_P_SJA1105, + .tpid2 = ETH_P_SJA1105, + }; + struct sja1105_table *table; + int i; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) + if (dsa_is_dsa_port(priv->ds, i)) + default_general_params.casc_port = i; + + table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS]; + + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_GENERAL_PARAMS_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT; + + /* This table only has a single entry */ + ((struct sja1105_general_params_entry *)table->entries)[0] = + default_general_params; + + return 0; +} + +#define SJA1105_RATE_MBPS(speed) (((speed) * 64000) / 1000) + +static inline void +sja1105_setup_policer(struct sja1105_l2_policing_entry *policing, + int index) +{ + policing[index].sharindx = index; + policing[index].smax = 65535; /* Burst size in bytes */ + policing[index].rate = SJA1105_RATE_MBPS(1000); + policing[index].maxlen = ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN; + policing[index].partition = 0; +} + +static int sja1105_init_l2_policing(struct sja1105_private *priv) +{ + struct sja1105_l2_policing_entry *policing; + struct sja1105_table *table; + int i, j, k; + + table = &priv->static_config.tables[BLK_IDX_L2_POLICING]; + + /* Discard previous L2 Policing Table */ + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_L2_POLICING_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = SJA1105_MAX_L2_POLICING_COUNT; + + policing = table->entries; + + /* k sweeps through all unicast policers (0-39). + * bcast sweeps through policers 40-44. + */ + for (i = 0, k = 0; i < SJA1105_NUM_PORTS; i++) { + int bcast = (SJA1105_NUM_PORTS * SJA1105_NUM_TC) + i; + + for (j = 0; j < SJA1105_NUM_TC; j++, k++) + sja1105_setup_policer(policing, k); + + /* Set up this port's policer for broadcast traffic */ + sja1105_setup_policer(policing, bcast); + } + return 0; +} + +static int sja1105_static_config_load(struct sja1105_private *priv, + struct sja1105_dt_port *ports) +{ + int rc; + + sja1105_static_config_free(&priv->static_config); + rc = sja1105_static_config_init(&priv->static_config, + priv->info->static_ops, + priv->info->device_id); + if (rc) + return rc; + + /* Build static configuration */ + rc = sja1105_init_mac_settings(priv); + if (rc < 0) + return rc; + rc = sja1105_init_mii_settings(priv, ports); + if (rc < 0) + return rc; + rc = sja1105_init_static_fdb(priv); + if (rc < 0) + return rc; + rc = sja1105_init_static_vlan(priv); + if (rc < 0) + return rc; + rc = sja1105_init_l2_lookup_params(priv); + if (rc < 0) + return rc; + rc = sja1105_init_l2_forwarding(priv); + if (rc < 0) + return rc; + rc = sja1105_init_l2_forwarding_params(priv); + if (rc < 0) + return rc; + rc = sja1105_init_l2_policing(priv); + if (rc < 0) + return rc; + rc = sja1105_init_general_params(priv); + if (rc < 0) + return rc; + + /* Send initial configuration to hardware via SPI */ + return sja1105_static_config_upload(priv); +} + +static int sja1105_parse_rgmii_delays(struct sja1105_private *priv, + const struct sja1105_dt_port *ports) +{ + int i; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + if (ports->role == XMII_MAC) + continue; + + if (ports->phy_mode == PHY_INTERFACE_MODE_RGMII_RXID || + ports->phy_mode == PHY_INTERFACE_MODE_RGMII_ID) + priv->rgmii_rx_delay[i] = true; + + if (ports->phy_mode == PHY_INTERFACE_MODE_RGMII_TXID || + ports->phy_mode == PHY_INTERFACE_MODE_RGMII_ID) + priv->rgmii_tx_delay[i] = true; + + if ((priv->rgmii_rx_delay[i] || priv->rgmii_tx_delay[i]) && + !priv->info->setup_rgmii_delay) + return -EINVAL; + } + return 0; +} + +static int sja1105_parse_ports_node(struct sja1105_private *priv, + struct sja1105_dt_port *ports, + struct device_node *ports_node) +{ + struct device *dev = &priv->spidev->dev; + struct device_node *child; + + for_each_child_of_node(ports_node, child) { + struct device_node *phy_node; + int phy_mode; + u32 index; + + /* Get switch port number from DT */ + if (of_property_read_u32(child, "reg", &index) < 0) { + dev_err(dev, "Port number not defined in device tree " + "(property \"reg\")\n"); + return -ENODEV; + } + + /* Get PHY mode from DT */ + phy_mode = of_get_phy_mode(child); + if (phy_mode < 0) { + dev_err(dev, "Failed to read phy-mode or " + "phy-interface-type property for port %d\n", + index); + return -ENODEV; + } + ports[index].phy_mode = phy_mode; + + phy_node = of_parse_phandle(child, "phy-handle", 0); + if (!phy_node) { + if (!of_phy_is_fixed_link(child)) { + dev_err(dev, "phy-handle or fixed-link " + "properties missing!\n"); + return -ENODEV; + } + /* phy-handle is missing, but fixed-link isn't. + * So it's a fixed link. Default to PHY role. + */ + ports[index].role = XMII_PHY; + } else { + /* phy-handle present => put port in MAC role */ + ports[index].role = XMII_MAC; + of_node_put(phy_node); + } + + /* The MAC/PHY role can be overridden with explicit bindings */ + if (of_property_read_bool(child, "sja1105,role-mac")) + ports[index].role = XMII_MAC; + else if (of_property_read_bool(child, "sja1105,role-phy")) + ports[index].role = XMII_PHY; + } + + return 0; +} + +static int sja1105_parse_dt(struct sja1105_private *priv, + struct sja1105_dt_port *ports) +{ + struct device *dev = &priv->spidev->dev; + struct device_node *switch_node = dev->of_node; + struct device_node *ports_node; + int rc; + + ports_node = of_get_child_by_name(switch_node, "ports"); + if (!ports_node) { + dev_err(dev, "Incorrect bindings: absent \"ports\" node\n"); + return -ENODEV; + } + + rc = sja1105_parse_ports_node(priv, ports, ports_node); + of_node_put(ports_node); + + return rc; +} + +/* Convert back and forth MAC speed from Mbps to SJA1105 encoding */ +static int sja1105_speed[] = { + [SJA1105_SPEED_AUTO] = 0, + [SJA1105_SPEED_10MBPS] = 10, + [SJA1105_SPEED_100MBPS] = 100, + [SJA1105_SPEED_1000MBPS] = 1000, +}; + +static sja1105_speed_t sja1105_get_speed_cfg(unsigned int speed_mbps) +{ + int i; + + for (i = SJA1105_SPEED_AUTO; i <= SJA1105_SPEED_1000MBPS; i++) + if (sja1105_speed[i] == speed_mbps) + return i; + return -EINVAL; +} + +/* Set link speed and enable/disable traffic I/O in the MAC configuration + * for a specific port. + * + * @speed_mbps: If 0, leave the speed unchanged, else adapt MAC to PHY speed. + * @enabled: Manage Rx and Tx settings for this port. Overrides the static + * configuration settings. + */ +static int sja1105_adjust_port_config(struct sja1105_private *priv, int port, + int speed_mbps, bool enabled) +{ + struct sja1105_xmii_params_entry *mii; + struct sja1105_mac_config_entry *mac; + struct device *dev = priv->ds->dev; + sja1105_phy_interface_t phy_mode; + sja1105_speed_t speed; + int rc; + + mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries; + mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; + + speed = sja1105_get_speed_cfg(speed_mbps); + if (speed_mbps && speed < 0) { + dev_err(dev, "Invalid speed %iMbps\n", speed_mbps); + return -EINVAL; + } + + /* If requested, overwrite SJA1105_SPEED_AUTO from the static MAC + * configuration table, since this will be used for the clocking setup, + * and we no longer need to store it in the static config (already told + * hardware we want auto during upload phase). + */ + if (speed_mbps) + mac[port].speed = speed; + else + mac[port].speed = SJA1105_SPEED_AUTO; + + /* On P/Q/R/S, one can read from the device via the MAC reconfiguration + * tables. On E/T, MAC reconfig tables are not readable, only writable. + * We have to *know* what the MAC looks like. For the sake of keeping + * the code common, we'll use the static configuration tables as a + * reasonable approximation for both E/T and P/Q/R/S. + */ + mac[port].ingress = enabled; + mac[port].egress = enabled; + + /* Write to the dynamic reconfiguration tables */ + rc = sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, + port, &mac[port], true); + if (rc < 0) { + dev_err(dev, "Failed to write MAC config: %d\n", rc); + return rc; + } + + /* Reconfigure the PLLs for the RGMII interfaces (required 125 MHz at + * gigabit, 25 MHz at 100 Mbps and 2.5 MHz at 10 Mbps). For MII and + * RMII no change of the clock setup is required. Actually, changing + * the clock setup does interrupt the clock signal for a certain time + * which causes trouble for all PHYs relying on this signal. + */ + if (!enabled) + return 0; + + phy_mode = mii->xmii_mode[port]; + if (phy_mode != XMII_MODE_RGMII) + return 0; + + return sja1105_clocking_setup_port(priv, port); +} + +static void sja1105_adjust_link(struct dsa_switch *ds, int port, + struct phy_device *phydev) +{ + struct sja1105_private *priv = ds->priv; + + if (!phydev->link) + sja1105_adjust_port_config(priv, port, 0, false); + else + sja1105_adjust_port_config(priv, port, phydev->speed, true); +} + +static void sja1105_phylink_validate(struct dsa_switch *ds, int port, + unsigned long *supported, + struct phylink_link_state *state) +{ + /* Construct a new mask which exhaustively contains all link features + * supported by the MAC, and then apply that (logical AND) to what will + * be sent to the PHY for "marketing". + */ + __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, }; + struct sja1105_private *priv = ds->priv; + struct sja1105_xmii_params_entry *mii; + + mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries; + + /* The MAC does not support pause frames, and also doesn't + * support half-duplex traffic modes. + */ + phylink_set(mask, Autoneg); + phylink_set(mask, MII); + phylink_set(mask, 10baseT_Full); + phylink_set(mask, 100baseT_Full); + if (mii->xmii_mode[port] == XMII_MODE_RGMII) + phylink_set(mask, 1000baseT_Full); + + bitmap_and(supported, supported, mask, __ETHTOOL_LINK_MODE_MASK_NBITS); + bitmap_and(state->advertising, state->advertising, mask, + __ETHTOOL_LINK_MODE_MASK_NBITS); +} + +/* First-generation switches have a 4-way set associative TCAM that + * holds the FDB entries. An FDB index spans from 0 to 1023 and is comprised of + * a "bin" (grouping of 4 entries) and a "way" (an entry within a bin). + * For the placement of a newly learnt FDB entry, the switch selects the bin + * based on a hash function, and the way within that bin incrementally. + */ +static inline int sja1105et_fdb_index(int bin, int way) +{ + return bin * SJA1105ET_FDB_BIN_SIZE + way; +} + +static int sja1105_is_fdb_entry_in_bin(struct sja1105_private *priv, int bin, + const u8 *addr, u16 vid, + struct sja1105_l2_lookup_entry *match, + int *last_unused) +{ + int way; + + for (way = 0; way < SJA1105ET_FDB_BIN_SIZE; way++) { + struct sja1105_l2_lookup_entry l2_lookup = {0}; + int index = sja1105et_fdb_index(bin, way); + + /* Skip unused entries, optionally marking them + * into the return value + */ + if (sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP, + index, &l2_lookup)) { + if (last_unused) + *last_unused = way; + continue; + } + + if (l2_lookup.macaddr == ether_addr_to_u64(addr) && + l2_lookup.vlanid == vid) { + if (match) + *match = l2_lookup; + return way; + } + } + /* Return an invalid entry index if not found */ + return -1; +} + +static int sja1105_fdb_add(struct dsa_switch *ds, int port, + const unsigned char *addr, u16 vid) +{ + struct sja1105_l2_lookup_entry l2_lookup = {0}; + struct sja1105_private *priv = ds->priv; + struct device *dev = ds->dev; + int last_unused = -1; + int bin, way; + + bin = sja1105_fdb_hash(priv, addr, vid); + + way = sja1105_is_fdb_entry_in_bin(priv, bin, addr, vid, + &l2_lookup, &last_unused); + if (way >= 0) { + /* We have an FDB entry. Is our port in the destination + * mask? If yes, we need to do nothing. If not, we need + * to rewrite the entry by adding this port to it. + */ + if (l2_lookup.destports & BIT(port)) + return 0; + l2_lookup.destports |= BIT(port); + } else { + int index = sja1105et_fdb_index(bin, way); + + /* We don't have an FDB entry. We construct a new one and + * try to find a place for it within the FDB table. + */ + l2_lookup.macaddr = ether_addr_to_u64(addr); + l2_lookup.destports = BIT(port); + l2_lookup.vlanid = vid; + + if (last_unused >= 0) { + way = last_unused; + } else { + /* Bin is full, need to evict somebody. + * Choose victim at random. If you get these messages + * often, you may need to consider changing the + * distribution function: + * static_config[BLK_IDX_L2_LOOKUP_PARAMS].entries->poly + */ + get_random_bytes(&way, sizeof(u8)); + way %= SJA1105ET_FDB_BIN_SIZE; + dev_warn(dev, "Warning, FDB bin %d full while adding entry for %pM. Evicting entry %u.\n", + bin, addr, way); + /* Evict entry */ + sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, + index, NULL, false); + } + } + l2_lookup.index = sja1105et_fdb_index(bin, way); + + return sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, + l2_lookup.index, &l2_lookup, + true); +} + +static int sja1105_fdb_del(struct dsa_switch *ds, int port, + const unsigned char *addr, u16 vid) +{ + struct sja1105_l2_lookup_entry l2_lookup = {0}; + struct sja1105_private *priv = ds->priv; + int index, bin, way; + bool keep; + + bin = sja1105_fdb_hash(priv, addr, vid); + way = sja1105_is_fdb_entry_in_bin(priv, bin, addr, vid, + &l2_lookup, NULL); + if (way < 0) + return 0; + index = sja1105et_fdb_index(bin, way); + + /* We have an FDB entry. Is our port in the destination mask? If yes, + * we need to remove it. If the resulting port mask becomes empty, we + * need to completely evict the FDB entry. + * Otherwise we just write it back. + */ + if (l2_lookup.destports & BIT(port)) + l2_lookup.destports &= ~BIT(port); + if (l2_lookup.destports) + keep = true; + else + keep = false; + + return sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, + index, &l2_lookup, keep); +} + +static int sja1105_fdb_dump(struct dsa_switch *ds, int port, + dsa_fdb_dump_cb_t *cb, void *data) +{ + struct sja1105_private *priv = ds->priv; + struct device *dev = ds->dev; + int i; + + for (i = 0; i < SJA1105_MAX_L2_LOOKUP_COUNT; i++) { + struct sja1105_l2_lookup_entry l2_lookup = {0}; + u8 macaddr[ETH_ALEN]; + int rc; + + rc = sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP, + i, &l2_lookup); + /* No fdb entry at i, not an issue */ + if (rc == -EINVAL) + continue; + if (rc) { + dev_err(dev, "Failed to dump FDB: %d\n", rc); + return rc; + } + + /* FDB dump callback is per port. This means we have to + * disregard a valid entry if it's not for this port, even if + * only to revisit it later. This is inefficient because the + * 1024-sized FDB table needs to be traversed 4 times through + * SPI during a 'bridge fdb show' command. + */ + if (!(l2_lookup.destports & BIT(port))) + continue; + u64_to_ether_addr(l2_lookup.macaddr, macaddr); + cb(macaddr, l2_lookup.vlanid, false, data); + } + return 0; +} + +/* This callback needs to be present */ +static int sja1105_mdb_prepare(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_mdb *mdb) +{ + return 0; +} + +static void sja1105_mdb_add(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_mdb *mdb) +{ + sja1105_fdb_add(ds, port, mdb->addr, mdb->vid); +} + +static int sja1105_mdb_del(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_mdb *mdb) +{ + return sja1105_fdb_del(ds, port, mdb->addr, mdb->vid); +} + +static int sja1105_bridge_member(struct dsa_switch *ds, int port, + struct net_device *br, bool member) +{ + struct sja1105_l2_forwarding_entry *l2_fwd; + struct sja1105_private *priv = ds->priv; + int i, rc; + + l2_fwd = priv->static_config.tables[BLK_IDX_L2_FORWARDING].entries; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + /* Add this port to the forwarding matrix of the + * other ports in the same bridge, and viceversa. + */ + if (!dsa_is_user_port(ds, i)) + continue; + /* For the ports already under the bridge, only one thing needs + * to be done, and that is to add this port to their + * reachability domain. So we can perform the SPI write for + * them immediately. However, for this port itself (the one + * that is new to the bridge), we need to add all other ports + * to its reachability domain. So we do that incrementally in + * this loop, and perform the SPI write only at the end, once + * the domain contains all other bridge ports. + */ + if (i == port) + continue; + if (dsa_to_port(ds, i)->bridge_dev != br) + continue; + sja1105_port_allow_traffic(l2_fwd, i, port, member); + sja1105_port_allow_traffic(l2_fwd, port, i, member); + + rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_FORWARDING, + i, &l2_fwd[i], true); + if (rc < 0) + return rc; + } + + return sja1105_dynamic_config_write(priv, BLK_IDX_L2_FORWARDING, + port, &l2_fwd[port], true); +} + +static int sja1105_bridge_join(struct dsa_switch *ds, int port, + struct net_device *br) +{ + return sja1105_bridge_member(ds, port, br, true); +} + +static void sja1105_bridge_leave(struct dsa_switch *ds, int port, + struct net_device *br) +{ + sja1105_bridge_member(ds, port, br, false); +} + +/* For situations where we need to change a setting at runtime that is only + * available through the static configuration, resetting the switch in order + * to upload the new static config is unavoidable. Back up the settings we + * modify at runtime (currently only MAC) and restore them after uploading, + * such that this operation is relatively seamless. + */ +static int sja1105_static_config_reload(struct sja1105_private *priv) +{ + struct sja1105_mac_config_entry *mac; + int speed_mbps[SJA1105_NUM_PORTS]; + int rc, i; + + mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; + + /* Back up settings changed by sja1105_adjust_port_config and + * and restore their defaults. + */ + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + speed_mbps[i] = sja1105_speed[mac[i].speed]; + mac[i].speed = SJA1105_SPEED_AUTO; + } + + /* Reset switch and send updated static configuration */ + rc = sja1105_static_config_upload(priv); + if (rc < 0) + goto out; + + /* Configure the CGU (PLLs) for MII and RMII PHYs. + * For these interfaces there is no dynamic configuration + * needed, since PLLs have same settings at all speeds. + */ + rc = sja1105_clocking_setup(priv); + if (rc < 0) + goto out; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + bool enabled = (speed_mbps[i] != 0); + + rc = sja1105_adjust_port_config(priv, i, speed_mbps[i], + enabled); + if (rc < 0) + goto out; + } +out: + return rc; +} + +/* The TPID setting belongs to the General Parameters table, + * which can only be partially reconfigured at runtime (and not the TPID). + * So a switch reset is required. + */ +static int sja1105_change_tpid(struct sja1105_private *priv, + u16 tpid, u16 tpid2) +{ + struct sja1105_general_params_entry *general_params; + struct sja1105_table *table; + + table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS]; + general_params = table->entries; + general_params->tpid = tpid; + general_params->tpid2 = tpid2; + return sja1105_static_config_reload(priv); +} + +static int sja1105_pvid_apply(struct sja1105_private *priv, int port, u16 pvid) +{ + struct sja1105_mac_config_entry *mac; + + mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; + + mac[port].vlanid = pvid; + + return sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port, + &mac[port], true); +} + +static int sja1105_is_vlan_configured(struct sja1105_private *priv, u16 vid) +{ + struct sja1105_vlan_lookup_entry *vlan; + int count, i; + + vlan = priv->static_config.tables[BLK_IDX_VLAN_LOOKUP].entries; + count = priv->static_config.tables[BLK_IDX_VLAN_LOOKUP].entry_count; + + for (i = 0; i < count; i++) + if (vlan[i].vlanid == vid) + return i; + + /* Return an invalid entry index if not found */ + return -1; +} + +static int sja1105_vlan_apply(struct sja1105_private *priv, int port, u16 vid, + bool enabled, bool untagged) +{ + struct sja1105_vlan_lookup_entry *vlan; + struct sja1105_table *table; + bool keep = true; + int match, rc; + + table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP]; + + match = sja1105_is_vlan_configured(priv, vid); + if (match < 0) { + /* Can't delete a missing entry. */ + if (!enabled) + return 0; + rc = sja1105_table_resize(table, table->entry_count + 1); + if (rc) + return rc; + match = table->entry_count - 1; + } + /* Assign pointer after the resize (it's new memory) */ + vlan = table->entries; + vlan[match].vlanid = vid; + if (enabled) { + vlan[match].vlan_bc |= BIT(port); + vlan[match].vmemb_port |= BIT(port); + } else { + vlan[match].vlan_bc &= ~BIT(port); + vlan[match].vmemb_port &= ~BIT(port); + } + /* Also unset tag_port if removing this VLAN was requested, + * just so we don't have a confusing bitmap (no practical purpose). + */ + if (untagged || !enabled) + vlan[match].tag_port &= ~BIT(port); + else + vlan[match].tag_port |= BIT(port); + /* If there's no port left as member of this VLAN, + * it's time for it to go. + */ + if (!vlan[match].vmemb_port) + keep = false; + + dev_dbg(priv->ds->dev, + "%s: port %d, vid %llu, broadcast domain 0x%llx, " + "port members 0x%llx, tagged ports 0x%llx, keep %d\n", + __func__, port, vlan[match].vlanid, vlan[match].vlan_bc, + vlan[match].vmemb_port, vlan[match].tag_port, keep); + + rc = sja1105_dynamic_config_write(priv, BLK_IDX_VLAN_LOOKUP, vid, + &vlan[match], keep); + if (rc < 0) + return rc; + + if (!keep) + return sja1105_table_delete_entry(table, match); + + return 0; +} + +static enum dsa_tag_protocol +sja1105_get_tag_protocol(struct dsa_switch *ds, int port) +{ + return DSA_TAG_PROTO_NONE; +} + +/* This callback needs to be present */ +static int sja1105_vlan_prepare(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan) +{ + return 0; +} + +static int sja1105_vlan_filtering(struct dsa_switch *ds, int port, bool enabled) +{ + struct sja1105_private *priv = ds->priv; + int rc; + + if (enabled) + /* Enable VLAN filtering. */ + rc = sja1105_change_tpid(priv, ETH_P_8021Q, ETH_P_8021AD); + else + /* Disable VLAN filtering. */ + rc = sja1105_change_tpid(priv, ETH_P_SJA1105, ETH_P_SJA1105); + if (rc) + dev_err(ds->dev, "Failed to change VLAN Ethertype\n"); + + return rc; +} + +static void sja1105_vlan_add(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan) +{ + struct sja1105_private *priv = ds->priv; + u16 vid; + int rc; + + for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) { + rc = sja1105_vlan_apply(priv, port, vid, true, vlan->flags & + BRIDGE_VLAN_INFO_UNTAGGED); + if (rc < 0) { + dev_err(ds->dev, "Failed to add VLAN %d to port %d: %d\n", + vid, port, rc); + return; + } + if (vlan->flags & BRIDGE_VLAN_INFO_PVID) { + rc = sja1105_pvid_apply(ds->priv, port, vid); + if (rc < 0) { + dev_err(ds->dev, "Failed to set pvid %d on port %d: %d\n", + vid, port, rc); + return; + } + } + } +} + +static int sja1105_vlan_del(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan) +{ + struct sja1105_private *priv = ds->priv; + u16 vid; + int rc; + + for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) { + rc = sja1105_vlan_apply(priv, port, vid, false, vlan->flags & + BRIDGE_VLAN_INFO_UNTAGGED); + if (rc < 0) { + dev_err(ds->dev, "Failed to remove VLAN %d from port %d: %d\n", + vid, port, rc); + return rc; + } + } + return 0; +} + +/* The programming model for the SJA1105 switch is "all-at-once" via static + * configuration tables. Some of these can be dynamically modified at runtime, + * but not the xMII mode parameters table. + * Furthermode, some PHYs may not have crystals for generating their clocks + * (e.g. RMII). Instead, their 50MHz clock is supplied via the SJA1105 port's + * ref_clk pin. So port clocking needs to be initialized early, before + * connecting to PHYs is attempted, otherwise they won't respond through MDIO. + * Setting correct PHY link speed does not matter now. + * But dsa_slave_phy_setup is called later than sja1105_setup, so the PHY + * bindings are not yet parsed by DSA core. We need to parse early so that we + * can populate the xMII mode parameters table. + */ +static int sja1105_setup(struct dsa_switch *ds) +{ + struct sja1105_dt_port ports[SJA1105_NUM_PORTS]; + struct sja1105_private *priv = ds->priv; + int rc; + + rc = sja1105_parse_dt(priv, ports); + if (rc < 0) { + dev_err(ds->dev, "Failed to parse DT: %d\n", rc); + return rc; + } + + /* Error out early if internal delays are required through DT + * and we can't apply them. + */ + rc = sja1105_parse_rgmii_delays(priv, ports); + if (rc < 0) { + dev_err(ds->dev, "RGMII delay not supported\n"); + return rc; + } + + /* Create and send configuration down to device */ + rc = sja1105_static_config_load(priv, ports); + if (rc < 0) { + dev_err(ds->dev, "Failed to load static config: %d\n", rc); + return rc; + } + /* Configure the CGU (PHY link modes and speeds) */ + rc = sja1105_clocking_setup(priv); + if (rc < 0) { + dev_err(ds->dev, "Failed to configure MII clocking: %d\n", rc); + return rc; + } + /* On SJA1105, VLAN filtering per se is always enabled in hardware. + * The only thing we can do to disable it is lie about what the 802.1Q + * EtherType is. + * So it will still try to apply VLAN filtering, but all ingress + * traffic (except frames received with EtherType of ETH_P_SJA1105) + * will be internally tagged with a distorted VLAN header where the + * TPID is ETH_P_SJA1105, and the VLAN ID is the port pvid. + */ + ds->vlan_filtering_is_global = true; + + return 0; +} + +/* The MAXAGE setting belongs to the L2 Forwarding Parameters table, + * which cannot be reconfigured at runtime. So a switch reset is required. + */ +static int sja1105_set_ageing_time(struct dsa_switch *ds, + unsigned int ageing_time) +{ + struct sja1105_l2_lookup_params_entry *l2_lookup_params; + struct sja1105_private *priv = ds->priv; + struct sja1105_table *table; + unsigned int maxage; + + table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS]; + l2_lookup_params = table->entries; + + maxage = SJA1105_AGEING_TIME_MS(ageing_time); + + if (l2_lookup_params->maxage == maxage) + return 0; + + l2_lookup_params->maxage = maxage; + + return sja1105_static_config_reload(priv); +} + +static const struct dsa_switch_ops sja1105_switch_ops = { + .get_tag_protocol = sja1105_get_tag_protocol, + .setup = sja1105_setup, + .adjust_link = sja1105_adjust_link, + .set_ageing_time = sja1105_set_ageing_time, + .phylink_validate = sja1105_phylink_validate, + .get_strings = sja1105_get_strings, + .get_ethtool_stats = sja1105_get_ethtool_stats, + .get_sset_count = sja1105_get_sset_count, + .port_fdb_dump = sja1105_fdb_dump, + .port_fdb_add = sja1105_fdb_add, + .port_fdb_del = sja1105_fdb_del, + .port_bridge_join = sja1105_bridge_join, + .port_bridge_leave = sja1105_bridge_leave, + .port_vlan_prepare = sja1105_vlan_prepare, + .port_vlan_filtering = sja1105_vlan_filtering, + .port_vlan_add = sja1105_vlan_add, + .port_vlan_del = sja1105_vlan_del, + .port_mdb_prepare = sja1105_mdb_prepare, + .port_mdb_add = sja1105_mdb_add, + .port_mdb_del = sja1105_mdb_del, +}; + +static int sja1105_check_device_id(struct sja1105_private *priv) +{ + const struct sja1105_regs *regs = priv->info->regs; + u8 prod_id[SJA1105_SIZE_DEVICE_ID] = {0}; + struct device *dev = &priv->spidev->dev; + u64 device_id; + u64 part_no; + int rc; + + rc = sja1105_spi_send_int(priv, SPI_READ, regs->device_id, + &device_id, SJA1105_SIZE_DEVICE_ID); + if (rc < 0) + return rc; + + if (device_id != priv->info->device_id) { + dev_err(dev, "Expected device ID 0x%llx but read 0x%llx\n", + priv->info->device_id, device_id); + return -ENODEV; + } + + rc = sja1105_spi_send_packed_buf(priv, SPI_READ, regs->prod_id, + prod_id, SJA1105_SIZE_DEVICE_ID); + if (rc < 0) + return rc; + + sja1105_unpack(prod_id, &part_no, 19, 4, SJA1105_SIZE_DEVICE_ID); + + if (part_no != priv->info->part_no) { + dev_err(dev, "Expected part number 0x%llx but read 0x%llx\n", + priv->info->part_no, part_no); + return -ENODEV; + } + + return 0; +} + +static int sja1105_probe(struct spi_device *spi) +{ + struct device *dev = &spi->dev; + struct sja1105_private *priv; + struct dsa_switch *ds; + int rc; + + if (!dev->of_node) { + dev_err(dev, "No DTS bindings for SJA1105 driver\n"); + return -EINVAL; + } + + priv = devm_kzalloc(dev, sizeof(struct sja1105_private), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + /* Configure the optional reset pin and bring up switch */ + priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(priv->reset_gpio)) + dev_dbg(dev, "reset-gpios not defined, ignoring\n"); + else + sja1105_hw_reset(priv->reset_gpio, 1, 1); + + /* Populate our driver private structure (priv) based on + * the device tree node that was probed (spi) + */ + priv->spidev = spi; + spi_set_drvdata(spi, priv); + + /* Configure the SPI bus */ + spi->bits_per_word = 8; + rc = spi_setup(spi); + if (rc < 0) { + dev_err(dev, "Could not init SPI\n"); + return rc; + } + + priv->info = of_device_get_match_data(dev); + + /* Detect hardware device */ + rc = sja1105_check_device_id(priv); + if (rc < 0) { + dev_err(dev, "Device ID check failed: %d\n", rc); + return rc; + } + + dev_info(dev, "Probed switch chip: %s\n", priv->info->name); + + ds = dsa_switch_alloc(dev, SJA1105_NUM_PORTS); + if (!ds) + return -ENOMEM; + + ds->ops = &sja1105_switch_ops; + ds->priv = priv; + priv->ds = ds; + + return dsa_register_switch(priv->ds); +} + +static int sja1105_remove(struct spi_device *spi) +{ + struct sja1105_private *priv = spi_get_drvdata(spi); + + dsa_unregister_switch(priv->ds); + sja1105_static_config_free(&priv->static_config); + return 0; +} + +static const struct of_device_id sja1105_dt_ids[] = { + { .compatible = "nxp,sja1105e", .data = &sja1105e_info }, + { .compatible = "nxp,sja1105t", .data = &sja1105t_info }, + { .compatible = "nxp,sja1105p", .data = &sja1105p_info }, + { .compatible = "nxp,sja1105q", .data = &sja1105q_info }, + { .compatible = "nxp,sja1105r", .data = &sja1105r_info }, + { .compatible = "nxp,sja1105s", .data = &sja1105s_info }, + { /* sentinel */ }, +}; +MODULE_DEVICE_TABLE(of, sja1105_dt_ids); + +static struct spi_driver sja1105_driver = { + .driver = { + .name = "sja1105", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(sja1105_dt_ids), + }, + .probe = sja1105_probe, + .remove = sja1105_remove, +}; + +module_spi_driver(sja1105_driver); + +MODULE_AUTHOR("Vladimir Oltean <olteanv@gmail.com>"); +MODULE_AUTHOR("Georg Waibel <georg.waibel@sensor-technik.de>"); +MODULE_DESCRIPTION("SJA1105 Driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/net/dsa/sja1105/sja1105_spi.c b/drivers/net/dsa/sja1105/sja1105_spi.c new file mode 100644 index 000000000000..244a94ccfc18 --- /dev/null +++ b/drivers/net/dsa/sja1105/sja1105_spi.c @@ -0,0 +1,590 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* Copyright (c) 2016-2018, NXP Semiconductors + * Copyright (c) 2018, Sensor-Technik Wiedemann GmbH + * Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ +#include <linux/spi/spi.h> +#include <linux/packing.h> +#include "sja1105.h" + +#define SJA1105_SIZE_PORT_CTRL 4 +#define SJA1105_SIZE_RESET_CMD 4 +#define SJA1105_SIZE_SPI_MSG_HEADER 4 +#define SJA1105_SIZE_SPI_MSG_MAXLEN (64 * 4) +#define SJA1105_SIZE_SPI_TRANSFER_MAX \ + (SJA1105_SIZE_SPI_MSG_HEADER + SJA1105_SIZE_SPI_MSG_MAXLEN) + +static int sja1105_spi_transfer(const struct sja1105_private *priv, + const void *tx, void *rx, int size) +{ + struct spi_device *spi = priv->spidev; + struct spi_transfer transfer = { + .tx_buf = tx, + .rx_buf = rx, + .len = size, + }; + struct spi_message msg; + int rc; + + if (size > SJA1105_SIZE_SPI_TRANSFER_MAX) { + dev_err(&spi->dev, "SPI message (%d) longer than max of %d\n", + size, SJA1105_SIZE_SPI_TRANSFER_MAX); + return -EMSGSIZE; + } + + spi_message_init(&msg); + spi_message_add_tail(&transfer, &msg); + + rc = spi_sync(spi, &msg); + if (rc < 0) { + dev_err(&spi->dev, "SPI transfer failed: %d\n", rc); + return rc; + } + + return rc; +} + +static void +sja1105_spi_message_pack(void *buf, const struct sja1105_spi_message *msg) +{ + const int size = SJA1105_SIZE_SPI_MSG_HEADER; + + memset(buf, 0, size); + + sja1105_pack(buf, &msg->access, 31, 31, size); + sja1105_pack(buf, &msg->read_count, 30, 25, size); + sja1105_pack(buf, &msg->address, 24, 4, size); +} + +/* If @rw is: + * - SPI_WRITE: creates and sends an SPI write message at absolute + * address reg_addr, taking size_bytes from *packed_buf + * - SPI_READ: creates and sends an SPI read message from absolute + * address reg_addr, writing size_bytes into *packed_buf + * + * This function should only be called if it is priorly known that + * @size_bytes is smaller than SIZE_SPI_MSG_MAXLEN. Larger packed buffers + * are chunked in smaller pieces by sja1105_spi_send_long_packed_buf below. + */ +int sja1105_spi_send_packed_buf(const struct sja1105_private *priv, + sja1105_spi_rw_mode_t rw, u64 reg_addr, + void *packed_buf, size_t size_bytes) +{ + u8 tx_buf[SJA1105_SIZE_SPI_TRANSFER_MAX] = {0}; + u8 rx_buf[SJA1105_SIZE_SPI_TRANSFER_MAX] = {0}; + const int msg_len = size_bytes + SJA1105_SIZE_SPI_MSG_HEADER; + struct sja1105_spi_message msg = {0}; + int rc; + + if (msg_len > SJA1105_SIZE_SPI_TRANSFER_MAX) + return -ERANGE; + + msg.access = rw; + msg.address = reg_addr; + if (rw == SPI_READ) + msg.read_count = size_bytes / 4; + + sja1105_spi_message_pack(tx_buf, &msg); + + if (rw == SPI_WRITE) + memcpy(tx_buf + SJA1105_SIZE_SPI_MSG_HEADER, + packed_buf, size_bytes); + + rc = sja1105_spi_transfer(priv, tx_buf, rx_buf, msg_len); + if (rc < 0) + return rc; + + if (rw == SPI_READ) + memcpy(packed_buf, rx_buf + SJA1105_SIZE_SPI_MSG_HEADER, + size_bytes); + + return 0; +} + +/* If @rw is: + * - SPI_WRITE: creates and sends an SPI write message at absolute + * address reg_addr, taking size_bytes from *packed_buf + * - SPI_READ: creates and sends an SPI read message from absolute + * address reg_addr, writing size_bytes into *packed_buf + * + * The u64 *value is unpacked, meaning that it's stored in the native + * CPU endianness and directly usable by software running on the core. + * + * This is a wrapper around sja1105_spi_send_packed_buf(). + */ +int sja1105_spi_send_int(const struct sja1105_private *priv, + sja1105_spi_rw_mode_t rw, u64 reg_addr, + u64 *value, u64 size_bytes) +{ + u8 packed_buf[SJA1105_SIZE_SPI_MSG_MAXLEN]; + int rc; + + if (size_bytes > SJA1105_SIZE_SPI_MSG_MAXLEN) + return -ERANGE; + + if (rw == SPI_WRITE) + sja1105_pack(packed_buf, value, 8 * size_bytes - 1, 0, + size_bytes); + + rc = sja1105_spi_send_packed_buf(priv, rw, reg_addr, packed_buf, + size_bytes); + + if (rw == SPI_READ) + sja1105_unpack(packed_buf, value, 8 * size_bytes - 1, 0, + size_bytes); + + return rc; +} + +/* Should be used if a @packed_buf larger than SJA1105_SIZE_SPI_MSG_MAXLEN + * must be sent/received. Splitting the buffer into chunks and assembling + * those into SPI messages is done automatically by this function. + */ +int sja1105_spi_send_long_packed_buf(const struct sja1105_private *priv, + sja1105_spi_rw_mode_t rw, u64 base_addr, + void *packed_buf, u64 buf_len) +{ + struct chunk { + void *buf_ptr; + int len; + u64 spi_address; + } chunk; + int distance_to_end; + int rc; + + /* Initialize chunk */ + chunk.buf_ptr = packed_buf; + chunk.spi_address = base_addr; + chunk.len = min_t(int, buf_len, SJA1105_SIZE_SPI_MSG_MAXLEN); + + while (chunk.len) { + rc = sja1105_spi_send_packed_buf(priv, rw, chunk.spi_address, + chunk.buf_ptr, chunk.len); + if (rc < 0) + return rc; + + chunk.buf_ptr += chunk.len; + chunk.spi_address += chunk.len / 4; + distance_to_end = (uintptr_t)(packed_buf + buf_len - + chunk.buf_ptr); + chunk.len = min(distance_to_end, SJA1105_SIZE_SPI_MSG_MAXLEN); + } + + return 0; +} + +/* Back-ported structure from UM11040 Table 112. + * Reset control register (addr. 100440h) + * In the SJA1105 E/T, only warm_rst and cold_rst are + * supported (exposed in UM10944 as rst_ctrl), but the bit + * offsets of warm_rst and cold_rst are actually reversed. + */ +struct sja1105_reset_cmd { + u64 switch_rst; + u64 cfg_rst; + u64 car_rst; + u64 otp_rst; + u64 warm_rst; + u64 cold_rst; + u64 por_rst; +}; + +static void +sja1105et_reset_cmd_pack(void *buf, const struct sja1105_reset_cmd *reset) +{ + const int size = SJA1105_SIZE_RESET_CMD; + + memset(buf, 0, size); + + sja1105_pack(buf, &reset->cold_rst, 3, 3, size); + sja1105_pack(buf, &reset->warm_rst, 2, 2, size); +} + +static void +sja1105pqrs_reset_cmd_pack(void *buf, const struct sja1105_reset_cmd *reset) +{ + const int size = SJA1105_SIZE_RESET_CMD; + + memset(buf, 0, size); + + sja1105_pack(buf, &reset->switch_rst, 8, 8, size); + sja1105_pack(buf, &reset->cfg_rst, 7, 7, size); + sja1105_pack(buf, &reset->car_rst, 5, 5, size); + sja1105_pack(buf, &reset->otp_rst, 4, 4, size); + sja1105_pack(buf, &reset->warm_rst, 3, 3, size); + sja1105_pack(buf, &reset->cold_rst, 2, 2, size); + sja1105_pack(buf, &reset->por_rst, 1, 1, size); +} + +static int sja1105et_reset_cmd(const void *ctx, const void *data) +{ + const struct sja1105_private *priv = ctx; + const struct sja1105_reset_cmd *reset = data; + const struct sja1105_regs *regs = priv->info->regs; + struct device *dev = priv->ds->dev; + u8 packed_buf[SJA1105_SIZE_RESET_CMD]; + + if (reset->switch_rst || + reset->cfg_rst || + reset->car_rst || + reset->otp_rst || + reset->por_rst) { + dev_err(dev, "Only warm and cold reset is supported " + "for SJA1105 E/T!\n"); + return -EINVAL; + } + + if (reset->warm_rst) + dev_dbg(dev, "Warm reset requested\n"); + if (reset->cold_rst) + dev_dbg(dev, "Cold reset requested\n"); + + sja1105et_reset_cmd_pack(packed_buf, reset); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, regs->rgu, + packed_buf, SJA1105_SIZE_RESET_CMD); +} + +static int sja1105pqrs_reset_cmd(const void *ctx, const void *data) +{ + const struct sja1105_private *priv = ctx; + const struct sja1105_reset_cmd *reset = data; + const struct sja1105_regs *regs = priv->info->regs; + struct device *dev = priv->ds->dev; + u8 packed_buf[SJA1105_SIZE_RESET_CMD]; + + if (reset->switch_rst) + dev_dbg(dev, "Main reset for all functional modules requested\n"); + if (reset->cfg_rst) + dev_dbg(dev, "Chip configuration reset requested\n"); + if (reset->car_rst) + dev_dbg(dev, "Clock and reset control logic reset requested\n"); + if (reset->otp_rst) + dev_dbg(dev, "OTP read cycle for reading product " + "config settings requested\n"); + if (reset->warm_rst) + dev_dbg(dev, "Warm reset requested\n"); + if (reset->cold_rst) + dev_dbg(dev, "Cold reset requested\n"); + if (reset->por_rst) + dev_dbg(dev, "Power-on reset requested\n"); + + sja1105pqrs_reset_cmd_pack(packed_buf, reset); + + return sja1105_spi_send_packed_buf(priv, SPI_WRITE, regs->rgu, + packed_buf, SJA1105_SIZE_RESET_CMD); +} + +static int sja1105_cold_reset(const struct sja1105_private *priv) +{ + struct sja1105_reset_cmd reset = {0}; + + reset.cold_rst = 1; + return priv->info->reset_cmd(priv, &reset); +} + +static int sja1105_inhibit_tx(const struct sja1105_private *priv, + const unsigned long *port_bitmap) +{ + const struct sja1105_regs *regs = priv->info->regs; + u64 inhibit_cmd; + int port, rc; + + rc = sja1105_spi_send_int(priv, SPI_READ, regs->port_control, + &inhibit_cmd, SJA1105_SIZE_PORT_CTRL); + if (rc < 0) + return rc; + + for_each_set_bit(port, port_bitmap, SJA1105_NUM_PORTS) + inhibit_cmd |= BIT(port); + + return sja1105_spi_send_int(priv, SPI_WRITE, regs->port_control, + &inhibit_cmd, SJA1105_SIZE_PORT_CTRL); +} + +struct sja1105_status { + u64 configs; + u64 crcchkl; + u64 ids; + u64 crcchkg; +}; + +/* This is not reading the entire General Status area, which is also + * divergent between E/T and P/Q/R/S, but only the relevant bits for + * ensuring that the static config upload procedure was successful. + */ +static void sja1105_status_unpack(void *buf, struct sja1105_status *status) +{ + /* So that addition translates to 4 bytes */ + u32 *p = buf; + + /* device_id is missing from the buffer, but we don't + * want to diverge from the manual definition of the + * register addresses, so we'll back off one step with + * the register pointer, and never access p[0]. + */ + p--; + sja1105_unpack(p + 0x1, &status->configs, 31, 31, 4); + sja1105_unpack(p + 0x1, &status->crcchkl, 30, 30, 4); + sja1105_unpack(p + 0x1, &status->ids, 29, 29, 4); + sja1105_unpack(p + 0x1, &status->crcchkg, 28, 28, 4); +} + +static int sja1105_status_get(struct sja1105_private *priv, + struct sja1105_status *status) +{ + const struct sja1105_regs *regs = priv->info->regs; + u8 packed_buf[4]; + int rc; + + rc = sja1105_spi_send_packed_buf(priv, SPI_READ, + regs->status, + packed_buf, 4); + if (rc < 0) + return rc; + + sja1105_status_unpack(packed_buf, status); + + return 0; +} + +/* Not const because unpacking priv->static_config into buffers and preparing + * for upload requires the recalculation of table CRCs and updating the + * structures with these. + */ +static int +static_config_buf_prepare_for_upload(struct sja1105_private *priv, + void *config_buf, int buf_len) +{ + struct sja1105_static_config *config = &priv->static_config; + struct sja1105_table_header final_header; + sja1105_config_valid_t valid; + char *final_header_ptr; + int crc_len; + + valid = sja1105_static_config_check_valid(config); + if (valid != SJA1105_CONFIG_OK) { + dev_err(&priv->spidev->dev, + sja1105_static_config_error_msg[valid]); + return -EINVAL; + } + + /* Write Device ID and config tables to config_buf */ + sja1105_static_config_pack(config_buf, config); + /* Recalculate CRC of the last header (right now 0xDEADBEEF). + * Don't include the CRC field itself. + */ + crc_len = buf_len - 4; + /* Read the whole table header */ + final_header_ptr = config_buf + buf_len - SJA1105_SIZE_TABLE_HEADER; + sja1105_table_header_packing(final_header_ptr, &final_header, UNPACK); + /* Modify */ + final_header.crc = sja1105_crc32(config_buf, crc_len); + /* Rewrite */ + sja1105_table_header_packing(final_header_ptr, &final_header, PACK); + + return 0; +} + +#define RETRIES 10 + +int sja1105_static_config_upload(struct sja1105_private *priv) +{ + unsigned long port_bitmap = GENMASK_ULL(SJA1105_NUM_PORTS - 1, 0); + struct sja1105_static_config *config = &priv->static_config; + const struct sja1105_regs *regs = priv->info->regs; + struct device *dev = &priv->spidev->dev; + struct sja1105_status status; + int rc, retries = RETRIES; + u8 *config_buf; + int buf_len; + + buf_len = sja1105_static_config_get_length(config); + config_buf = kcalloc(buf_len, sizeof(char), GFP_KERNEL); + if (!config_buf) + return -ENOMEM; + + rc = static_config_buf_prepare_for_upload(priv, config_buf, buf_len); + if (rc < 0) { + dev_err(dev, "Invalid config, cannot upload\n"); + return -EINVAL; + } + /* Prevent PHY jabbering during switch reset by inhibiting + * Tx on all ports and waiting for current packet to drain. + * Otherwise, the PHY will see an unterminated Ethernet packet. + */ + rc = sja1105_inhibit_tx(priv, &port_bitmap); + if (rc < 0) { + dev_err(dev, "Failed to inhibit Tx on ports\n"); + return -ENXIO; + } + /* Wait for an eventual egress packet to finish transmission + * (reach IFG). It is guaranteed that a second one will not + * follow, and that switch cold reset is thus safe + */ + usleep_range(500, 1000); + do { + /* Put the SJA1105 in programming mode */ + rc = sja1105_cold_reset(priv); + if (rc < 0) { + dev_err(dev, "Failed to reset switch, retrying...\n"); + continue; + } + /* Wait for the switch to come out of reset */ + usleep_range(1000, 5000); + /* Upload the static config to the device */ + rc = sja1105_spi_send_long_packed_buf(priv, SPI_WRITE, + regs->config, + config_buf, buf_len); + if (rc < 0) { + dev_err(dev, "Failed to upload config, retrying...\n"); + continue; + } + /* Check that SJA1105 responded well to the config upload */ + rc = sja1105_status_get(priv, &status); + if (rc < 0) + continue; + + if (status.ids == 1) { + dev_err(dev, "Mismatch between hardware and static config " + "device id. Wrote 0x%llx, wants 0x%llx\n", + config->device_id, priv->info->device_id); + continue; + } + if (status.crcchkl == 1) { + dev_err(dev, "Switch reported invalid local CRC on " + "the uploaded config, retrying...\n"); + continue; + } + if (status.crcchkg == 1) { + dev_err(dev, "Switch reported invalid global CRC on " + "the uploaded config, retrying...\n"); + continue; + } + if (status.configs == 0) { + dev_err(dev, "Switch reported that configuration is " + "invalid, retrying...\n"); + continue; + } + } while (--retries && (status.crcchkl == 1 || status.crcchkg == 1 || + status.configs == 0 || status.ids == 1)); + + if (!retries) { + rc = -EIO; + dev_err(dev, "Failed to upload config to device, giving up\n"); + goto out; + } else if (retries != RETRIES - 1) { + dev_info(dev, "Succeeded after %d tried\n", RETRIES - retries); + } + + dev_info(dev, "Reset switch and programmed static config\n"); +out: + kfree(config_buf); + return rc; +} + +struct sja1105_regs sja1105et_regs = { + .device_id = 0x0, + .prod_id = 0x100BC3, + .status = 0x1, + .port_control = 0x11, + .config = 0x020000, + .rgu = 0x100440, + .pad_mii_tx = {0x100800, 0x100802, 0x100804, 0x100806, 0x100808}, + .rmii_pll1 = 0x10000A, + .cgu_idiv = {0x10000B, 0x10000C, 0x10000D, 0x10000E, 0x10000F}, + /* UM10944.pdf, Table 86, ACU Register overview */ + .rgmii_pad_mii_tx = {0x100800, 0x100802, 0x100804, 0x100806, 0x100808}, + .mac = {0x200, 0x202, 0x204, 0x206, 0x208}, + .mac_hl1 = {0x400, 0x410, 0x420, 0x430, 0x440}, + .mac_hl2 = {0x600, 0x610, 0x620, 0x630, 0x640}, + /* UM10944.pdf, Table 78, CGU Register overview */ + .mii_tx_clk = {0x100013, 0x10001A, 0x100021, 0x100028, 0x10002F}, + .mii_rx_clk = {0x100014, 0x10001B, 0x100022, 0x100029, 0x100030}, + .mii_ext_tx_clk = {0x100018, 0x10001F, 0x100026, 0x10002D, 0x100034}, + .mii_ext_rx_clk = {0x100019, 0x100020, 0x100027, 0x10002E, 0x100035}, + .rgmii_tx_clk = {0x100016, 0x10001D, 0x100024, 0x10002B, 0x100032}, + .rmii_ref_clk = {0x100015, 0x10001C, 0x100023, 0x10002A, 0x100031}, + .rmii_ext_tx_clk = {0x100018, 0x10001F, 0x100026, 0x10002D, 0x100034}, +}; + +struct sja1105_regs sja1105pqrs_regs = { + .device_id = 0x0, + .prod_id = 0x100BC3, + .status = 0x1, + .port_control = 0x12, + .config = 0x020000, + .rgu = 0x100440, + .pad_mii_tx = {0x100800, 0x100802, 0x100804, 0x100806, 0x100808}, + .rmii_pll1 = 0x10000A, + .cgu_idiv = {0x10000B, 0x10000C, 0x10000D, 0x10000E, 0x10000F}, + /* UM10944.pdf, Table 86, ACU Register overview */ + .rgmii_pad_mii_tx = {0x100800, 0x100802, 0x100804, 0x100806, 0x100808}, + .mac = {0x200, 0x202, 0x204, 0x206, 0x208}, + .mac_hl1 = {0x400, 0x410, 0x420, 0x430, 0x440}, + .mac_hl2 = {0x600, 0x610, 0x620, 0x630, 0x640}, + /* UM11040.pdf, Table 114 */ + .mii_tx_clk = {0x100013, 0x100019, 0x10001F, 0x100025, 0x10002B}, + .mii_rx_clk = {0x100014, 0x10001A, 0x100020, 0x100026, 0x10002C}, + .mii_ext_tx_clk = {0x100017, 0x10001D, 0x100023, 0x100029, 0x10002F}, + .mii_ext_rx_clk = {0x100018, 0x10001E, 0x100024, 0x10002A, 0x100030}, + .rgmii_tx_clk = {0x100016, 0x10001C, 0x100022, 0x100028, 0x10002E}, + .rmii_ref_clk = {0x100015, 0x10001B, 0x100021, 0x100027, 0x10002D}, + .rmii_ext_tx_clk = {0x100017, 0x10001D, 0x100023, 0x100029, 0x10002F}, + .qlevel = {0x604, 0x614, 0x624, 0x634, 0x644}, +}; + +struct sja1105_info sja1105e_info = { + .device_id = SJA1105E_DEVICE_ID, + .part_no = SJA1105ET_PART_NO, + .static_ops = sja1105e_table_ops, + .dyn_ops = sja1105et_dyn_ops, + .reset_cmd = sja1105et_reset_cmd, + .regs = &sja1105et_regs, + .name = "SJA1105E", +}; +struct sja1105_info sja1105t_info = { + .device_id = SJA1105T_DEVICE_ID, + .part_no = SJA1105ET_PART_NO, + .static_ops = sja1105t_table_ops, + .dyn_ops = sja1105et_dyn_ops, + .reset_cmd = sja1105et_reset_cmd, + .regs = &sja1105et_regs, + .name = "SJA1105T", +}; +struct sja1105_info sja1105p_info = { + .device_id = SJA1105PR_DEVICE_ID, + .part_no = SJA1105P_PART_NO, + .static_ops = sja1105p_table_ops, + .dyn_ops = sja1105pqrs_dyn_ops, + .reset_cmd = sja1105pqrs_reset_cmd, + .regs = &sja1105pqrs_regs, + .name = "SJA1105P", +}; +struct sja1105_info sja1105q_info = { + .device_id = SJA1105QS_DEVICE_ID, + .part_no = SJA1105Q_PART_NO, + .static_ops = sja1105q_table_ops, + .dyn_ops = sja1105pqrs_dyn_ops, + .reset_cmd = sja1105pqrs_reset_cmd, + .regs = &sja1105pqrs_regs, + .name = "SJA1105Q", +}; +struct sja1105_info sja1105r_info = { + .device_id = SJA1105PR_DEVICE_ID, + .part_no = SJA1105R_PART_NO, + .static_ops = sja1105r_table_ops, + .dyn_ops = sja1105pqrs_dyn_ops, + .reset_cmd = sja1105pqrs_reset_cmd, + .regs = &sja1105pqrs_regs, + .name = "SJA1105R", +}; +struct sja1105_info sja1105s_info = { + .device_id = SJA1105QS_DEVICE_ID, + .part_no = SJA1105S_PART_NO, + .static_ops = sja1105s_table_ops, + .dyn_ops = sja1105pqrs_dyn_ops, + .regs = &sja1105pqrs_regs, + .reset_cmd = sja1105pqrs_reset_cmd, + .name = "SJA1105S", +}; diff --git a/drivers/net/dsa/sja1105/sja1105_static_config.c b/drivers/net/dsa/sja1105/sja1105_static_config.c new file mode 100644 index 000000000000..b3c992b0abb0 --- /dev/null +++ b/drivers/net/dsa/sja1105/sja1105_static_config.c @@ -0,0 +1,987 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* Copyright (c) 2016-2018, NXP Semiconductors + * Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ +#include "sja1105_static_config.h" +#include <linux/crc32.h> +#include <linux/slab.h> +#include <linux/string.h> +#include <linux/errno.h> + +/* Convenience wrappers over the generic packing functions. These take into + * account the SJA1105 memory layout quirks and provide some level of + * programmer protection against incorrect API use. The errors are not expected + * to occur durring runtime, therefore printing and swallowing them here is + * appropriate instead of clutterring up higher-level code. + */ +void sja1105_pack(void *buf, const u64 *val, int start, int end, size_t len) +{ + int rc = packing(buf, (u64 *)val, start, end, len, + PACK, QUIRK_LSW32_IS_FIRST); + + if (likely(!rc)) + return; + + if (rc == -EINVAL) { + pr_err("Start bit (%d) expected to be larger than end (%d)\n", + start, end); + } else if (rc == -ERANGE) { + if ((start - end + 1) > 64) + pr_err("Field %d-%d too large for 64 bits!\n", + start, end); + else + pr_err("Cannot store %llx inside bits %d-%d (would truncate)\n", + *val, start, end); + } + dump_stack(); +} + +void sja1105_unpack(const void *buf, u64 *val, int start, int end, size_t len) +{ + int rc = packing((void *)buf, val, start, end, len, + UNPACK, QUIRK_LSW32_IS_FIRST); + + if (likely(!rc)) + return; + + if (rc == -EINVAL) + pr_err("Start bit (%d) expected to be larger than end (%d)\n", + start, end); + else if (rc == -ERANGE) + pr_err("Field %d-%d too large for 64 bits!\n", + start, end); + dump_stack(); +} + +void sja1105_packing(void *buf, u64 *val, int start, int end, + size_t len, enum packing_op op) +{ + int rc = packing(buf, val, start, end, len, op, QUIRK_LSW32_IS_FIRST); + + if (likely(!rc)) + return; + + if (rc == -EINVAL) { + pr_err("Start bit (%d) expected to be larger than end (%d)\n", + start, end); + } else if (rc == -ERANGE) { + if ((start - end + 1) > 64) + pr_err("Field %d-%d too large for 64 bits!\n", + start, end); + else + pr_err("Cannot store %llx inside bits %d-%d (would truncate)\n", + *val, start, end); + } + dump_stack(); +} + +/* Little-endian Ethernet CRC32 of data packed as big-endian u32 words */ +u32 sja1105_crc32(const void *buf, size_t len) +{ + unsigned int i; + u64 word; + u32 crc; + + /* seed */ + crc = ~0; + for (i = 0; i < len; i += 4) { + sja1105_unpack((void *)buf + i, &word, 31, 0, 4); + crc = crc32_le(crc, (u8 *)&word, 4); + } + return ~crc; +} + +static size_t sja1105et_general_params_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105ET_SIZE_GENERAL_PARAMS_ENTRY; + struct sja1105_general_params_entry *entry = entry_ptr; + + sja1105_packing(buf, &entry->vllupformat, 319, 319, size, op); + sja1105_packing(buf, &entry->mirr_ptacu, 318, 318, size, op); + sja1105_packing(buf, &entry->switchid, 317, 315, size, op); + sja1105_packing(buf, &entry->hostprio, 314, 312, size, op); + sja1105_packing(buf, &entry->mac_fltres1, 311, 264, size, op); + sja1105_packing(buf, &entry->mac_fltres0, 263, 216, size, op); + sja1105_packing(buf, &entry->mac_flt1, 215, 168, size, op); + sja1105_packing(buf, &entry->mac_flt0, 167, 120, size, op); + sja1105_packing(buf, &entry->incl_srcpt1, 119, 119, size, op); + sja1105_packing(buf, &entry->incl_srcpt0, 118, 118, size, op); + sja1105_packing(buf, &entry->send_meta1, 117, 117, size, op); + sja1105_packing(buf, &entry->send_meta0, 116, 116, size, op); + sja1105_packing(buf, &entry->casc_port, 115, 113, size, op); + sja1105_packing(buf, &entry->host_port, 112, 110, size, op); + sja1105_packing(buf, &entry->mirr_port, 109, 107, size, op); + sja1105_packing(buf, &entry->vlmarker, 106, 75, size, op); + sja1105_packing(buf, &entry->vlmask, 74, 43, size, op); + sja1105_packing(buf, &entry->tpid, 42, 27, size, op); + sja1105_packing(buf, &entry->ignore2stf, 26, 26, size, op); + sja1105_packing(buf, &entry->tpid2, 25, 10, size, op); + return size; +} + +static size_t +sja1105pqrs_general_params_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105PQRS_SIZE_GENERAL_PARAMS_ENTRY; + struct sja1105_general_params_entry *entry = entry_ptr; + + sja1105_packing(buf, &entry->vllupformat, 351, 351, size, op); + sja1105_packing(buf, &entry->mirr_ptacu, 350, 350, size, op); + sja1105_packing(buf, &entry->switchid, 349, 347, size, op); + sja1105_packing(buf, &entry->hostprio, 346, 344, size, op); + sja1105_packing(buf, &entry->mac_fltres1, 343, 296, size, op); + sja1105_packing(buf, &entry->mac_fltres0, 295, 248, size, op); + sja1105_packing(buf, &entry->mac_flt1, 247, 200, size, op); + sja1105_packing(buf, &entry->mac_flt0, 199, 152, size, op); + sja1105_packing(buf, &entry->incl_srcpt1, 151, 151, size, op); + sja1105_packing(buf, &entry->incl_srcpt0, 150, 150, size, op); + sja1105_packing(buf, &entry->send_meta1, 149, 149, size, op); + sja1105_packing(buf, &entry->send_meta0, 148, 148, size, op); + sja1105_packing(buf, &entry->casc_port, 147, 145, size, op); + sja1105_packing(buf, &entry->host_port, 144, 142, size, op); + sja1105_packing(buf, &entry->mirr_port, 141, 139, size, op); + sja1105_packing(buf, &entry->vlmarker, 138, 107, size, op); + sja1105_packing(buf, &entry->vlmask, 106, 75, size, op); + sja1105_packing(buf, &entry->tpid, 74, 59, size, op); + sja1105_packing(buf, &entry->ignore2stf, 58, 58, size, op); + sja1105_packing(buf, &entry->tpid2, 57, 42, size, op); + sja1105_packing(buf, &entry->queue_ts, 41, 41, size, op); + sja1105_packing(buf, &entry->egrmirrvid, 40, 29, size, op); + sja1105_packing(buf, &entry->egrmirrpcp, 28, 26, size, op); + sja1105_packing(buf, &entry->egrmirrdei, 25, 25, size, op); + sja1105_packing(buf, &entry->replay_port, 24, 22, size, op); + return size; +} + +static size_t +sja1105_l2_forwarding_params_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105_SIZE_L2_FORWARDING_PARAMS_ENTRY; + struct sja1105_l2_forwarding_params_entry *entry = entry_ptr; + int offset, i; + + sja1105_packing(buf, &entry->max_dynp, 95, 93, size, op); + for (i = 0, offset = 13; i < 8; i++, offset += 10) + sja1105_packing(buf, &entry->part_spc[i], + offset + 9, offset + 0, size, op); + return size; +} + +size_t sja1105_l2_forwarding_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105_SIZE_L2_FORWARDING_ENTRY; + struct sja1105_l2_forwarding_entry *entry = entry_ptr; + int offset, i; + + sja1105_packing(buf, &entry->bc_domain, 63, 59, size, op); + sja1105_packing(buf, &entry->reach_port, 58, 54, size, op); + sja1105_packing(buf, &entry->fl_domain, 53, 49, size, op); + for (i = 0, offset = 25; i < 8; i++, offset += 3) + sja1105_packing(buf, &entry->vlan_pmap[i], + offset + 2, offset + 0, size, op); + return size; +} + +static size_t +sja1105et_l2_lookup_params_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105ET_SIZE_L2_LOOKUP_PARAMS_ENTRY; + struct sja1105_l2_lookup_params_entry *entry = entry_ptr; + + sja1105_packing(buf, &entry->maxage, 31, 17, size, op); + sja1105_packing(buf, &entry->dyn_tbsz, 16, 14, size, op); + sja1105_packing(buf, &entry->poly, 13, 6, size, op); + sja1105_packing(buf, &entry->shared_learn, 5, 5, size, op); + sja1105_packing(buf, &entry->no_enf_hostprt, 4, 4, size, op); + sja1105_packing(buf, &entry->no_mgmt_learn, 3, 3, size, op); + return size; +} + +static size_t +sja1105pqrs_l2_lookup_params_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105PQRS_SIZE_L2_LOOKUP_PARAMS_ENTRY; + struct sja1105_l2_lookup_params_entry *entry = entry_ptr; + + sja1105_packing(buf, &entry->maxage, 57, 43, size, op); + sja1105_packing(buf, &entry->shared_learn, 27, 27, size, op); + sja1105_packing(buf, &entry->no_enf_hostprt, 26, 26, size, op); + sja1105_packing(buf, &entry->no_mgmt_learn, 25, 25, size, op); + return size; +} + +size_t sja1105et_l2_lookup_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105ET_SIZE_L2_LOOKUP_ENTRY; + struct sja1105_l2_lookup_entry *entry = entry_ptr; + + sja1105_packing(buf, &entry->vlanid, 95, 84, size, op); + sja1105_packing(buf, &entry->macaddr, 83, 36, size, op); + sja1105_packing(buf, &entry->destports, 35, 31, size, op); + sja1105_packing(buf, &entry->enfport, 30, 30, size, op); + sja1105_packing(buf, &entry->index, 29, 20, size, op); + return size; +} + +size_t sja1105pqrs_l2_lookup_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY; + struct sja1105_l2_lookup_entry *entry = entry_ptr; + + /* These are static L2 lookup entries, so the structure + * should match UM11040 Table 16/17 definitions when + * LOCKEDS is 1. + */ + sja1105_packing(buf, &entry->vlanid, 81, 70, size, op); + sja1105_packing(buf, &entry->macaddr, 69, 22, size, op); + sja1105_packing(buf, &entry->destports, 21, 17, size, op); + sja1105_packing(buf, &entry->enfport, 16, 16, size, op); + sja1105_packing(buf, &entry->index, 15, 6, size, op); + return size; +} + +static size_t sja1105_l2_policing_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105_SIZE_L2_POLICING_ENTRY; + struct sja1105_l2_policing_entry *entry = entry_ptr; + + sja1105_packing(buf, &entry->sharindx, 63, 58, size, op); + sja1105_packing(buf, &entry->smax, 57, 42, size, op); + sja1105_packing(buf, &entry->rate, 41, 26, size, op); + sja1105_packing(buf, &entry->maxlen, 25, 15, size, op); + sja1105_packing(buf, &entry->partition, 14, 12, size, op); + return size; +} + +static size_t sja1105et_mac_config_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105ET_SIZE_MAC_CONFIG_ENTRY; + struct sja1105_mac_config_entry *entry = entry_ptr; + int offset, i; + + for (i = 0, offset = 72; i < 8; i++, offset += 19) { + sja1105_packing(buf, &entry->enabled[i], + offset + 0, offset + 0, size, op); + sja1105_packing(buf, &entry->base[i], + offset + 9, offset + 1, size, op); + sja1105_packing(buf, &entry->top[i], + offset + 18, offset + 10, size, op); + } + sja1105_packing(buf, &entry->ifg, 71, 67, size, op); + sja1105_packing(buf, &entry->speed, 66, 65, size, op); + sja1105_packing(buf, &entry->tp_delin, 64, 49, size, op); + sja1105_packing(buf, &entry->tp_delout, 48, 33, size, op); + sja1105_packing(buf, &entry->maxage, 32, 25, size, op); + sja1105_packing(buf, &entry->vlanprio, 24, 22, size, op); + sja1105_packing(buf, &entry->vlanid, 21, 10, size, op); + sja1105_packing(buf, &entry->ing_mirr, 9, 9, size, op); + sja1105_packing(buf, &entry->egr_mirr, 8, 8, size, op); + sja1105_packing(buf, &entry->drpnona664, 7, 7, size, op); + sja1105_packing(buf, &entry->drpdtag, 6, 6, size, op); + sja1105_packing(buf, &entry->drpuntag, 5, 5, size, op); + sja1105_packing(buf, &entry->retag, 4, 4, size, op); + sja1105_packing(buf, &entry->dyn_learn, 3, 3, size, op); + sja1105_packing(buf, &entry->egress, 2, 2, size, op); + sja1105_packing(buf, &entry->ingress, 1, 1, size, op); + return size; +} + +size_t sja1105pqrs_mac_config_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105PQRS_SIZE_MAC_CONFIG_ENTRY; + struct sja1105_mac_config_entry *entry = entry_ptr; + int offset, i; + + for (i = 0, offset = 104; i < 8; i++, offset += 19) { + sja1105_packing(buf, &entry->enabled[i], + offset + 0, offset + 0, size, op); + sja1105_packing(buf, &entry->base[i], + offset + 9, offset + 1, size, op); + sja1105_packing(buf, &entry->top[i], + offset + 18, offset + 10, size, op); + } + sja1105_packing(buf, &entry->ifg, 103, 99, size, op); + sja1105_packing(buf, &entry->speed, 98, 97, size, op); + sja1105_packing(buf, &entry->tp_delin, 96, 81, size, op); + sja1105_packing(buf, &entry->tp_delout, 80, 65, size, op); + sja1105_packing(buf, &entry->maxage, 64, 57, size, op); + sja1105_packing(buf, &entry->vlanprio, 56, 54, size, op); + sja1105_packing(buf, &entry->vlanid, 53, 42, size, op); + sja1105_packing(buf, &entry->ing_mirr, 41, 41, size, op); + sja1105_packing(buf, &entry->egr_mirr, 40, 40, size, op); + sja1105_packing(buf, &entry->drpnona664, 39, 39, size, op); + sja1105_packing(buf, &entry->drpdtag, 38, 38, size, op); + sja1105_packing(buf, &entry->drpuntag, 35, 35, size, op); + sja1105_packing(buf, &entry->retag, 34, 34, size, op); + sja1105_packing(buf, &entry->dyn_learn, 33, 33, size, op); + sja1105_packing(buf, &entry->egress, 32, 32, size, op); + sja1105_packing(buf, &entry->ingress, 31, 31, size, op); + return size; +} + +size_t sja1105_vlan_lookup_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105_SIZE_VLAN_LOOKUP_ENTRY; + struct sja1105_vlan_lookup_entry *entry = entry_ptr; + + sja1105_packing(buf, &entry->ving_mirr, 63, 59, size, op); + sja1105_packing(buf, &entry->vegr_mirr, 58, 54, size, op); + sja1105_packing(buf, &entry->vmemb_port, 53, 49, size, op); + sja1105_packing(buf, &entry->vlan_bc, 48, 44, size, op); + sja1105_packing(buf, &entry->tag_port, 43, 39, size, op); + sja1105_packing(buf, &entry->vlanid, 38, 27, size, op); + return size; +} + +static size_t sja1105_xmii_params_entry_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105_SIZE_XMII_PARAMS_ENTRY; + struct sja1105_xmii_params_entry *entry = entry_ptr; + int offset, i; + + for (i = 0, offset = 17; i < 5; i++, offset += 3) { + sja1105_packing(buf, &entry->xmii_mode[i], + offset + 1, offset + 0, size, op); + sja1105_packing(buf, &entry->phy_mac[i], + offset + 2, offset + 2, size, op); + } + return size; +} + +size_t sja1105_table_header_packing(void *buf, void *entry_ptr, + enum packing_op op) +{ + const size_t size = SJA1105_SIZE_TABLE_HEADER; + struct sja1105_table_header *entry = entry_ptr; + + sja1105_packing(buf, &entry->block_id, 31, 24, size, op); + sja1105_packing(buf, &entry->len, 55, 32, size, op); + sja1105_packing(buf, &entry->crc, 95, 64, size, op); + return size; +} + +/* WARNING: the *hdr pointer is really non-const, because it is + * modifying the CRC of the header for a 2-stage packing operation + */ +void +sja1105_table_header_pack_with_crc(void *buf, struct sja1105_table_header *hdr) +{ + /* First pack the table as-is, then calculate the CRC, and + * finally put the proper CRC into the packed buffer + */ + memset(buf, 0, SJA1105_SIZE_TABLE_HEADER); + sja1105_table_header_packing(buf, hdr, PACK); + hdr->crc = sja1105_crc32(buf, SJA1105_SIZE_TABLE_HEADER - 4); + sja1105_pack(buf + SJA1105_SIZE_TABLE_HEADER - 4, &hdr->crc, 31, 0, 4); +} + +static void sja1105_table_write_crc(u8 *table_start, u8 *crc_ptr) +{ + u64 computed_crc; + int len_bytes; + + len_bytes = (uintptr_t)(crc_ptr - table_start); + computed_crc = sja1105_crc32(table_start, len_bytes); + sja1105_pack(crc_ptr, &computed_crc, 31, 0, 4); +} + +/* The block IDs that the switches support are unfortunately sparse, so keep a + * mapping table to "block indices" and translate back and forth so that we + * don't waste useless memory in struct sja1105_static_config. + * Also, since the block id comes from essentially untrusted input (unpacking + * the static config from userspace) it has to be sanitized (range-checked) + * before blindly indexing kernel memory with the blk_idx. + */ +static u64 blk_id_map[BLK_IDX_MAX] = { + [BLK_IDX_L2_LOOKUP] = BLKID_L2_LOOKUP, + [BLK_IDX_L2_POLICING] = BLKID_L2_POLICING, + [BLK_IDX_VLAN_LOOKUP] = BLKID_VLAN_LOOKUP, + [BLK_IDX_L2_FORWARDING] = BLKID_L2_FORWARDING, + [BLK_IDX_MAC_CONFIG] = BLKID_MAC_CONFIG, + [BLK_IDX_L2_LOOKUP_PARAMS] = BLKID_L2_LOOKUP_PARAMS, + [BLK_IDX_L2_FORWARDING_PARAMS] = BLKID_L2_FORWARDING_PARAMS, + [BLK_IDX_GENERAL_PARAMS] = BLKID_GENERAL_PARAMS, + [BLK_IDX_XMII_PARAMS] = BLKID_XMII_PARAMS, +}; + +const char *sja1105_static_config_error_msg[] = { + [SJA1105_CONFIG_OK] = "", + [SJA1105_MISSING_L2_POLICING_TABLE] = + "l2-policing-table needs to have at least one entry", + [SJA1105_MISSING_L2_FORWARDING_TABLE] = + "l2-forwarding-table is either missing or incomplete", + [SJA1105_MISSING_L2_FORWARDING_PARAMS_TABLE] = + "l2-forwarding-parameters-table is missing", + [SJA1105_MISSING_GENERAL_PARAMS_TABLE] = + "general-parameters-table is missing", + [SJA1105_MISSING_VLAN_TABLE] = + "vlan-lookup-table needs to have at least the default untagged VLAN", + [SJA1105_MISSING_XMII_TABLE] = + "xmii-table is missing", + [SJA1105_MISSING_MAC_TABLE] = + "mac-configuration-table needs to contain an entry for each port", + [SJA1105_OVERCOMMITTED_FRAME_MEMORY] = + "Not allowed to overcommit frame memory. L2 memory partitions " + "and VL memory partitions share the same space. The sum of all " + "16 memory partitions is not allowed to be larger than 929 " + "128-byte blocks (or 910 with retagging). Please adjust " + "l2-forwarding-parameters-table.part_spc and/or " + "vl-forwarding-parameters-table.partspc.", +}; + +sja1105_config_valid_t +static_config_check_memory_size(const struct sja1105_table *tables) +{ + const struct sja1105_l2_forwarding_params_entry *l2_fwd_params; + int i, mem = 0; + + l2_fwd_params = tables[BLK_IDX_L2_FORWARDING_PARAMS].entries; + + for (i = 0; i < 8; i++) + mem += l2_fwd_params->part_spc[i]; + + if (mem > SJA1105_MAX_FRAME_MEMORY) + return SJA1105_OVERCOMMITTED_FRAME_MEMORY; + + return SJA1105_CONFIG_OK; +} + +sja1105_config_valid_t +sja1105_static_config_check_valid(const struct sja1105_static_config *config) +{ + const struct sja1105_table *tables = config->tables; +#define IS_FULL(blk_idx) \ + (tables[blk_idx].entry_count == tables[blk_idx].ops->max_entry_count) + + if (tables[BLK_IDX_L2_POLICING].entry_count == 0) + return SJA1105_MISSING_L2_POLICING_TABLE; + + if (tables[BLK_IDX_VLAN_LOOKUP].entry_count == 0) + return SJA1105_MISSING_VLAN_TABLE; + + if (!IS_FULL(BLK_IDX_L2_FORWARDING)) + return SJA1105_MISSING_L2_FORWARDING_TABLE; + + if (!IS_FULL(BLK_IDX_MAC_CONFIG)) + return SJA1105_MISSING_MAC_TABLE; + + if (!IS_FULL(BLK_IDX_L2_FORWARDING_PARAMS)) + return SJA1105_MISSING_L2_FORWARDING_PARAMS_TABLE; + + if (!IS_FULL(BLK_IDX_GENERAL_PARAMS)) + return SJA1105_MISSING_GENERAL_PARAMS_TABLE; + + if (!IS_FULL(BLK_IDX_XMII_PARAMS)) + return SJA1105_MISSING_XMII_TABLE; + + return static_config_check_memory_size(tables); +#undef IS_FULL +} + +void +sja1105_static_config_pack(void *buf, struct sja1105_static_config *config) +{ + struct sja1105_table_header header = {0}; + enum sja1105_blk_idx i; + char *p = buf; + int j; + + sja1105_pack(p, &config->device_id, 31, 0, 4); + p += SJA1105_SIZE_DEVICE_ID; + + for (i = 0; i < BLK_IDX_MAX; i++) { + const struct sja1105_table *table; + char *table_start; + + table = &config->tables[i]; + if (!table->entry_count) + continue; + + header.block_id = blk_id_map[i]; + header.len = table->entry_count * + table->ops->packed_entry_size / 4; + sja1105_table_header_pack_with_crc(p, &header); + p += SJA1105_SIZE_TABLE_HEADER; + table_start = p; + for (j = 0; j < table->entry_count; j++) { + u8 *entry_ptr = table->entries; + + entry_ptr += j * table->ops->unpacked_entry_size; + memset(p, 0, table->ops->packed_entry_size); + table->ops->packing(p, entry_ptr, PACK); + p += table->ops->packed_entry_size; + } + sja1105_table_write_crc(table_start, p); + p += 4; + } + /* Final header: + * Block ID does not matter + * Length of 0 marks that header is final + * CRC will be replaced on-the-fly on "config upload" + */ + header.block_id = 0; + header.len = 0; + header.crc = 0xDEADBEEF; + memset(p, 0, SJA1105_SIZE_TABLE_HEADER); + sja1105_table_header_packing(p, &header, PACK); +} + +size_t +sja1105_static_config_get_length(const struct sja1105_static_config *config) +{ + unsigned int sum; + unsigned int header_count; + enum sja1105_blk_idx i; + + /* Ending header */ + header_count = 1; + sum = SJA1105_SIZE_DEVICE_ID; + + /* Tables (headers and entries) */ + for (i = 0; i < BLK_IDX_MAX; i++) { + const struct sja1105_table *table; + + table = &config->tables[i]; + if (table->entry_count) + header_count++; + + sum += table->ops->packed_entry_size * table->entry_count; + } + /* Headers have an additional CRC at the end */ + sum += header_count * (SJA1105_SIZE_TABLE_HEADER + 4); + /* Last header does not have an extra CRC because there is no data */ + sum -= 4; + + return sum; +} + +/* Compatibility matrices */ + +/* SJA1105E: First generation, no TTEthernet */ +struct sja1105_table_ops sja1105e_table_ops[BLK_IDX_MAX] = { + [BLK_IDX_L2_LOOKUP] = { + .packing = sja1105et_l2_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_entry), + .packed_entry_size = SJA1105ET_SIZE_L2_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_COUNT, + }, + [BLK_IDX_L2_POLICING] = { + .packing = sja1105_l2_policing_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_policing_entry), + .packed_entry_size = SJA1105_SIZE_L2_POLICING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_POLICING_COUNT, + }, + [BLK_IDX_VLAN_LOOKUP] = { + .packing = sja1105_vlan_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_vlan_lookup_entry), + .packed_entry_size = SJA1105_SIZE_VLAN_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_VLAN_LOOKUP_COUNT, + }, + [BLK_IDX_L2_FORWARDING] = { + .packing = sja1105_l2_forwarding_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_COUNT, + }, + [BLK_IDX_MAC_CONFIG] = { + .packing = sja1105et_mac_config_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_mac_config_entry), + .packed_entry_size = SJA1105ET_SIZE_MAC_CONFIG_ENTRY, + .max_entry_count = SJA1105_MAX_MAC_CONFIG_COUNT, + }, + [BLK_IDX_L2_LOOKUP_PARAMS] = { + .packing = sja1105et_l2_lookup_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_params_entry), + .packed_entry_size = SJA1105ET_SIZE_L2_LOOKUP_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, + }, + [BLK_IDX_L2_FORWARDING_PARAMS] = { + .packing = sja1105_l2_forwarding_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_params_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT, + }, + [BLK_IDX_GENERAL_PARAMS] = { + .packing = sja1105et_general_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_general_params_entry), + .packed_entry_size = SJA1105ET_SIZE_GENERAL_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT, + }, + [BLK_IDX_XMII_PARAMS] = { + .packing = sja1105_xmii_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_xmii_params_entry), + .packed_entry_size = SJA1105_SIZE_XMII_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_XMII_PARAMS_COUNT, + }, +}; + +/* SJA1105T: First generation, TTEthernet */ +struct sja1105_table_ops sja1105t_table_ops[BLK_IDX_MAX] = { + [BLK_IDX_L2_LOOKUP] = { + .packing = sja1105et_l2_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_entry), + .packed_entry_size = SJA1105ET_SIZE_L2_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_COUNT, + }, + [BLK_IDX_L2_POLICING] = { + .packing = sja1105_l2_policing_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_policing_entry), + .packed_entry_size = SJA1105_SIZE_L2_POLICING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_POLICING_COUNT, + }, + [BLK_IDX_VLAN_LOOKUP] = { + .packing = sja1105_vlan_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_vlan_lookup_entry), + .packed_entry_size = SJA1105_SIZE_VLAN_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_VLAN_LOOKUP_COUNT, + }, + [BLK_IDX_L2_FORWARDING] = { + .packing = sja1105_l2_forwarding_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_COUNT, + }, + [BLK_IDX_MAC_CONFIG] = { + .packing = sja1105et_mac_config_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_mac_config_entry), + .packed_entry_size = SJA1105ET_SIZE_MAC_CONFIG_ENTRY, + .max_entry_count = SJA1105_MAX_MAC_CONFIG_COUNT, + }, + [BLK_IDX_L2_LOOKUP_PARAMS] = { + .packing = sja1105et_l2_lookup_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_params_entry), + .packed_entry_size = SJA1105ET_SIZE_L2_LOOKUP_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, + }, + [BLK_IDX_L2_FORWARDING_PARAMS] = { + .packing = sja1105_l2_forwarding_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_params_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT, + }, + [BLK_IDX_GENERAL_PARAMS] = { + .packing = sja1105et_general_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_general_params_entry), + .packed_entry_size = SJA1105ET_SIZE_GENERAL_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT, + }, + [BLK_IDX_XMII_PARAMS] = { + .packing = sja1105_xmii_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_xmii_params_entry), + .packed_entry_size = SJA1105_SIZE_XMII_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_XMII_PARAMS_COUNT, + }, +}; + +/* SJA1105P: Second generation, no TTEthernet, no SGMII */ +struct sja1105_table_ops sja1105p_table_ops[BLK_IDX_MAX] = { + [BLK_IDX_L2_LOOKUP] = { + .packing = sja1105pqrs_l2_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_entry), + .packed_entry_size = SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_COUNT, + }, + [BLK_IDX_L2_POLICING] = { + .packing = sja1105_l2_policing_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_policing_entry), + .packed_entry_size = SJA1105_SIZE_L2_POLICING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_POLICING_COUNT, + }, + [BLK_IDX_VLAN_LOOKUP] = { + .packing = sja1105_vlan_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_vlan_lookup_entry), + .packed_entry_size = SJA1105_SIZE_VLAN_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_VLAN_LOOKUP_COUNT, + }, + [BLK_IDX_L2_FORWARDING] = { + .packing = sja1105_l2_forwarding_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_COUNT, + }, + [BLK_IDX_MAC_CONFIG] = { + .packing = sja1105pqrs_mac_config_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_mac_config_entry), + .packed_entry_size = SJA1105PQRS_SIZE_MAC_CONFIG_ENTRY, + .max_entry_count = SJA1105_MAX_MAC_CONFIG_COUNT, + }, + [BLK_IDX_L2_LOOKUP_PARAMS] = { + .packing = sja1105pqrs_l2_lookup_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_params_entry), + .packed_entry_size = SJA1105PQRS_SIZE_L2_LOOKUP_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, + }, + [BLK_IDX_L2_FORWARDING_PARAMS] = { + .packing = sja1105_l2_forwarding_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_params_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT, + }, + [BLK_IDX_GENERAL_PARAMS] = { + .packing = sja1105pqrs_general_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_general_params_entry), + .packed_entry_size = SJA1105PQRS_SIZE_GENERAL_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT, + }, + [BLK_IDX_XMII_PARAMS] = { + .packing = sja1105_xmii_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_xmii_params_entry), + .packed_entry_size = SJA1105_SIZE_XMII_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_XMII_PARAMS_COUNT, + }, +}; + +/* SJA1105Q: Second generation, TTEthernet, no SGMII */ +struct sja1105_table_ops sja1105q_table_ops[BLK_IDX_MAX] = { + [BLK_IDX_L2_LOOKUP] = { + .packing = sja1105pqrs_l2_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_entry), + .packed_entry_size = SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_COUNT, + }, + [BLK_IDX_L2_POLICING] = { + .packing = sja1105_l2_policing_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_policing_entry), + .packed_entry_size = SJA1105_SIZE_L2_POLICING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_POLICING_COUNT, + }, + [BLK_IDX_VLAN_LOOKUP] = { + .packing = sja1105_vlan_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_vlan_lookup_entry), + .packed_entry_size = SJA1105_SIZE_VLAN_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_VLAN_LOOKUP_COUNT, + }, + [BLK_IDX_L2_FORWARDING] = { + .packing = sja1105_l2_forwarding_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_COUNT, + }, + [BLK_IDX_MAC_CONFIG] = { + .packing = sja1105pqrs_mac_config_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_mac_config_entry), + .packed_entry_size = SJA1105PQRS_SIZE_MAC_CONFIG_ENTRY, + .max_entry_count = SJA1105_MAX_MAC_CONFIG_COUNT, + }, + [BLK_IDX_L2_LOOKUP_PARAMS] = { + .packing = sja1105pqrs_l2_lookup_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_params_entry), + .packed_entry_size = SJA1105PQRS_SIZE_L2_LOOKUP_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, + }, + [BLK_IDX_L2_FORWARDING_PARAMS] = { + .packing = sja1105_l2_forwarding_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_params_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT, + }, + [BLK_IDX_GENERAL_PARAMS] = { + .packing = sja1105pqrs_general_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_general_params_entry), + .packed_entry_size = SJA1105PQRS_SIZE_GENERAL_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT, + }, + [BLK_IDX_XMII_PARAMS] = { + .packing = sja1105_xmii_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_xmii_params_entry), + .packed_entry_size = SJA1105_SIZE_XMII_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_XMII_PARAMS_COUNT, + }, +}; + +/* SJA1105R: Second generation, no TTEthernet, SGMII */ +struct sja1105_table_ops sja1105r_table_ops[BLK_IDX_MAX] = { + [BLK_IDX_L2_LOOKUP] = { + .packing = sja1105pqrs_l2_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_entry), + .packed_entry_size = SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_COUNT, + }, + [BLK_IDX_L2_POLICING] = { + .packing = sja1105_l2_policing_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_policing_entry), + .packed_entry_size = SJA1105_SIZE_L2_POLICING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_POLICING_COUNT, + }, + [BLK_IDX_VLAN_LOOKUP] = { + .packing = sja1105_vlan_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_vlan_lookup_entry), + .packed_entry_size = SJA1105_SIZE_VLAN_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_VLAN_LOOKUP_COUNT, + }, + [BLK_IDX_L2_FORWARDING] = { + .packing = sja1105_l2_forwarding_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_COUNT, + }, + [BLK_IDX_MAC_CONFIG] = { + .packing = sja1105pqrs_mac_config_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_mac_config_entry), + .packed_entry_size = SJA1105PQRS_SIZE_MAC_CONFIG_ENTRY, + .max_entry_count = SJA1105_MAX_MAC_CONFIG_COUNT, + }, + [BLK_IDX_L2_LOOKUP_PARAMS] = { + .packing = sja1105pqrs_l2_lookup_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_params_entry), + .packed_entry_size = SJA1105PQRS_SIZE_L2_LOOKUP_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, + }, + [BLK_IDX_L2_FORWARDING_PARAMS] = { + .packing = sja1105_l2_forwarding_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_params_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT, + }, + [BLK_IDX_GENERAL_PARAMS] = { + .packing = sja1105pqrs_general_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_general_params_entry), + .packed_entry_size = SJA1105PQRS_SIZE_GENERAL_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT, + }, + [BLK_IDX_XMII_PARAMS] = { + .packing = sja1105_xmii_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_xmii_params_entry), + .packed_entry_size = SJA1105_SIZE_XMII_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_XMII_PARAMS_COUNT, + }, +}; + +/* SJA1105S: Second generation, TTEthernet, SGMII */ +struct sja1105_table_ops sja1105s_table_ops[BLK_IDX_MAX] = { + [BLK_IDX_L2_LOOKUP] = { + .packing = sja1105pqrs_l2_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_entry), + .packed_entry_size = SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_COUNT, + }, + [BLK_IDX_L2_POLICING] = { + .packing = sja1105_l2_policing_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_policing_entry), + .packed_entry_size = SJA1105_SIZE_L2_POLICING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_POLICING_COUNT, + }, + [BLK_IDX_VLAN_LOOKUP] = { + .packing = sja1105_vlan_lookup_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_vlan_lookup_entry), + .packed_entry_size = SJA1105_SIZE_VLAN_LOOKUP_ENTRY, + .max_entry_count = SJA1105_MAX_VLAN_LOOKUP_COUNT, + }, + [BLK_IDX_L2_FORWARDING] = { + .packing = sja1105_l2_forwarding_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_COUNT, + }, + [BLK_IDX_MAC_CONFIG] = { + .packing = sja1105pqrs_mac_config_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_mac_config_entry), + .packed_entry_size = SJA1105PQRS_SIZE_MAC_CONFIG_ENTRY, + .max_entry_count = SJA1105_MAX_MAC_CONFIG_COUNT, + }, + [BLK_IDX_L2_LOOKUP_PARAMS] = { + .packing = sja1105pqrs_l2_lookup_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_lookup_params_entry), + .packed_entry_size = SJA1105PQRS_SIZE_L2_LOOKUP_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, + }, + [BLK_IDX_L2_FORWARDING_PARAMS] = { + .packing = sja1105_l2_forwarding_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_l2_forwarding_params_entry), + .packed_entry_size = SJA1105_SIZE_L2_FORWARDING_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT, + }, + [BLK_IDX_GENERAL_PARAMS] = { + .packing = sja1105pqrs_general_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_general_params_entry), + .packed_entry_size = SJA1105PQRS_SIZE_GENERAL_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT, + }, + [BLK_IDX_XMII_PARAMS] = { + .packing = sja1105_xmii_params_entry_packing, + .unpacked_entry_size = sizeof(struct sja1105_xmii_params_entry), + .packed_entry_size = SJA1105_SIZE_XMII_PARAMS_ENTRY, + .max_entry_count = SJA1105_MAX_XMII_PARAMS_COUNT, + }, +}; + +int sja1105_static_config_init(struct sja1105_static_config *config, + const struct sja1105_table_ops *static_ops, + u64 device_id) +{ + enum sja1105_blk_idx i; + + *config = (struct sja1105_static_config) {0}; + + /* Transfer static_ops array from priv into per-table ops + * for handier access + */ + for (i = 0; i < BLK_IDX_MAX; i++) + config->tables[i].ops = &static_ops[i]; + + config->device_id = device_id; + return 0; +} + +void sja1105_static_config_free(struct sja1105_static_config *config) +{ + enum sja1105_blk_idx i; + + for (i = 0; i < BLK_IDX_MAX; i++) { + if (config->tables[i].entry_count) { + kfree(config->tables[i].entries); + config->tables[i].entry_count = 0; + } + } +} + +int sja1105_table_delete_entry(struct sja1105_table *table, int i) +{ + size_t entry_size = table->ops->unpacked_entry_size; + u8 *entries = table->entries; + + if (i > table->entry_count) + return -ERANGE; + + memmove(entries + i * entry_size, entries + (i + 1) * entry_size, + (table->entry_count - i) * entry_size); + + table->entry_count--; + + return 0; +} + +/* No pointers to table->entries should be kept when this is called. */ +int sja1105_table_resize(struct sja1105_table *table, size_t new_count) +{ + size_t entry_size = table->ops->unpacked_entry_size; + void *new_entries, *old_entries = table->entries; + + if (new_count > table->ops->max_entry_count) + return -ERANGE; + + new_entries = kcalloc(new_count, entry_size, GFP_KERNEL); + if (!new_entries) + return -ENOMEM; + + memcpy(new_entries, old_entries, min(new_count, table->entry_count) * + entry_size); + + table->entries = new_entries; + table->entry_count = new_count; + kfree(old_entries); + return 0; +} diff --git a/drivers/net/dsa/sja1105/sja1105_static_config.h b/drivers/net/dsa/sja1105/sja1105_static_config.h new file mode 100644 index 000000000000..069ca8fd059c --- /dev/null +++ b/drivers/net/dsa/sja1105/sja1105_static_config.h @@ -0,0 +1,253 @@ +/* SPDX-License-Identifier: BSD-3-Clause + * Copyright (c) 2016-2018, NXP Semiconductors + * Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ +#ifndef _SJA1105_STATIC_CONFIG_H +#define _SJA1105_STATIC_CONFIG_H + +#include <linux/packing.h> +#include <linux/types.h> +#include <asm/types.h> + +#define SJA1105_SIZE_DEVICE_ID 4 +#define SJA1105_SIZE_TABLE_HEADER 12 +#define SJA1105_SIZE_L2_POLICING_ENTRY 8 +#define SJA1105_SIZE_VLAN_LOOKUP_ENTRY 8 +#define SJA1105_SIZE_L2_FORWARDING_ENTRY 8 +#define SJA1105_SIZE_L2_FORWARDING_PARAMS_ENTRY 12 +#define SJA1105_SIZE_XMII_PARAMS_ENTRY 4 +#define SJA1105ET_SIZE_L2_LOOKUP_ENTRY 12 +#define SJA1105ET_SIZE_MAC_CONFIG_ENTRY 28 +#define SJA1105ET_SIZE_L2_LOOKUP_PARAMS_ENTRY 4 +#define SJA1105ET_SIZE_GENERAL_PARAMS_ENTRY 40 +#define SJA1105PQRS_SIZE_L2_LOOKUP_ENTRY 20 +#define SJA1105PQRS_SIZE_MAC_CONFIG_ENTRY 32 +#define SJA1105PQRS_SIZE_L2_LOOKUP_PARAMS_ENTRY 16 +#define SJA1105PQRS_SIZE_GENERAL_PARAMS_ENTRY 44 + +/* UM10944.pdf Page 11, Table 2. Configuration Blocks */ +enum { + BLKID_L2_LOOKUP = 0x05, + BLKID_L2_POLICING = 0x06, + BLKID_VLAN_LOOKUP = 0x07, + BLKID_L2_FORWARDING = 0x08, + BLKID_MAC_CONFIG = 0x09, + BLKID_L2_LOOKUP_PARAMS = 0x0D, + BLKID_L2_FORWARDING_PARAMS = 0x0E, + BLKID_GENERAL_PARAMS = 0x11, + BLKID_XMII_PARAMS = 0x4E, +}; + +enum sja1105_blk_idx { + BLK_IDX_L2_LOOKUP = 0, + BLK_IDX_L2_POLICING, + BLK_IDX_VLAN_LOOKUP, + BLK_IDX_L2_FORWARDING, + BLK_IDX_MAC_CONFIG, + BLK_IDX_L2_LOOKUP_PARAMS, + BLK_IDX_L2_FORWARDING_PARAMS, + BLK_IDX_GENERAL_PARAMS, + BLK_IDX_XMII_PARAMS, + BLK_IDX_MAX, + /* Fake block indices that are only valid for dynamic access */ + BLK_IDX_MGMT_ROUTE, + BLK_IDX_MAX_DYN, + BLK_IDX_INVAL = -1, +}; + +#define SJA1105_MAX_L2_LOOKUP_COUNT 1024 +#define SJA1105_MAX_L2_POLICING_COUNT 45 +#define SJA1105_MAX_VLAN_LOOKUP_COUNT 4096 +#define SJA1105_MAX_L2_FORWARDING_COUNT 13 +#define SJA1105_MAX_MAC_CONFIG_COUNT 5 +#define SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT 1 +#define SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT 1 +#define SJA1105_MAX_GENERAL_PARAMS_COUNT 1 +#define SJA1105_MAX_XMII_PARAMS_COUNT 1 + +#define SJA1105_MAX_FRAME_MEMORY 929 + +#define SJA1105E_DEVICE_ID 0x9C00000Cull +#define SJA1105T_DEVICE_ID 0x9E00030Eull +#define SJA1105PR_DEVICE_ID 0xAF00030Eull +#define SJA1105QS_DEVICE_ID 0xAE00030Eull + +#define SJA1105ET_PART_NO 0x9A83 +#define SJA1105P_PART_NO 0x9A84 +#define SJA1105Q_PART_NO 0x9A85 +#define SJA1105R_PART_NO 0x9A86 +#define SJA1105S_PART_NO 0x9A87 + +struct sja1105_general_params_entry { + u64 vllupformat; + u64 mirr_ptacu; + u64 switchid; + u64 hostprio; + u64 mac_fltres1; + u64 mac_fltres0; + u64 mac_flt1; + u64 mac_flt0; + u64 incl_srcpt1; + u64 incl_srcpt0; + u64 send_meta1; + u64 send_meta0; + u64 casc_port; + u64 host_port; + u64 mirr_port; + u64 vlmarker; + u64 vlmask; + u64 tpid; + u64 ignore2stf; + u64 tpid2; + /* P/Q/R/S only */ + u64 queue_ts; + u64 egrmirrvid; + u64 egrmirrpcp; + u64 egrmirrdei; + u64 replay_port; +}; + +struct sja1105_vlan_lookup_entry { + u64 ving_mirr; + u64 vegr_mirr; + u64 vmemb_port; + u64 vlan_bc; + u64 tag_port; + u64 vlanid; +}; + +struct sja1105_l2_lookup_entry { + u64 vlanid; + u64 macaddr; + u64 destports; + u64 enfport; + u64 index; +}; + +struct sja1105_l2_lookup_params_entry { + u64 maxage; /* Shared */ + u64 dyn_tbsz; /* E/T only */ + u64 poly; /* E/T only */ + u64 shared_learn; /* Shared */ + u64 no_enf_hostprt; /* Shared */ + u64 no_mgmt_learn; /* Shared */ +}; + +struct sja1105_l2_forwarding_entry { + u64 bc_domain; + u64 reach_port; + u64 fl_domain; + u64 vlan_pmap[8]; +}; + +struct sja1105_l2_forwarding_params_entry { + u64 max_dynp; + u64 part_spc[8]; +}; + +struct sja1105_l2_policing_entry { + u64 sharindx; + u64 smax; + u64 rate; + u64 maxlen; + u64 partition; +}; + +struct sja1105_mac_config_entry { + u64 top[8]; + u64 base[8]; + u64 enabled[8]; + u64 ifg; + u64 speed; + u64 tp_delin; + u64 tp_delout; + u64 maxage; + u64 vlanprio; + u64 vlanid; + u64 ing_mirr; + u64 egr_mirr; + u64 drpnona664; + u64 drpdtag; + u64 drpuntag; + u64 retag; + u64 dyn_learn; + u64 egress; + u64 ingress; +}; + +struct sja1105_xmii_params_entry { + u64 phy_mac[5]; + u64 xmii_mode[5]; +}; + +struct sja1105_table_header { + u64 block_id; + u64 len; + u64 crc; +}; + +struct sja1105_table_ops { + size_t (*packing)(void *buf, void *entry_ptr, enum packing_op op); + size_t unpacked_entry_size; + size_t packed_entry_size; + size_t max_entry_count; +}; + +struct sja1105_table { + const struct sja1105_table_ops *ops; + size_t entry_count; + void *entries; +}; + +struct sja1105_static_config { + u64 device_id; + struct sja1105_table tables[BLK_IDX_MAX]; +}; + +extern struct sja1105_table_ops sja1105e_table_ops[BLK_IDX_MAX]; +extern struct sja1105_table_ops sja1105t_table_ops[BLK_IDX_MAX]; +extern struct sja1105_table_ops sja1105p_table_ops[BLK_IDX_MAX]; +extern struct sja1105_table_ops sja1105q_table_ops[BLK_IDX_MAX]; +extern struct sja1105_table_ops sja1105r_table_ops[BLK_IDX_MAX]; +extern struct sja1105_table_ops sja1105s_table_ops[BLK_IDX_MAX]; + +size_t sja1105_table_header_packing(void *buf, void *hdr, enum packing_op op); +void +sja1105_table_header_pack_with_crc(void *buf, struct sja1105_table_header *hdr); +size_t +sja1105_static_config_get_length(const struct sja1105_static_config *config); + +typedef enum { + SJA1105_CONFIG_OK = 0, + SJA1105_MISSING_L2_POLICING_TABLE, + SJA1105_MISSING_L2_FORWARDING_TABLE, + SJA1105_MISSING_L2_FORWARDING_PARAMS_TABLE, + SJA1105_MISSING_GENERAL_PARAMS_TABLE, + SJA1105_MISSING_VLAN_TABLE, + SJA1105_MISSING_XMII_TABLE, + SJA1105_MISSING_MAC_TABLE, + SJA1105_OVERCOMMITTED_FRAME_MEMORY, +} sja1105_config_valid_t; + +extern const char *sja1105_static_config_error_msg[]; + +sja1105_config_valid_t +sja1105_static_config_check_valid(const struct sja1105_static_config *config); +void +sja1105_static_config_pack(void *buf, struct sja1105_static_config *config); +int sja1105_static_config_init(struct sja1105_static_config *config, + const struct sja1105_table_ops *static_ops, + u64 device_id); +void sja1105_static_config_free(struct sja1105_static_config *config); + +int sja1105_table_delete_entry(struct sja1105_table *table, int i); +int sja1105_table_resize(struct sja1105_table *table, size_t new_count); + +u32 sja1105_crc32(const void *buf, size_t len); + +void sja1105_pack(void *buf, const u64 *val, int start, int end, size_t len); +void sja1105_unpack(const void *buf, u64 *val, int start, int end, size_t len); +void sja1105_packing(void *buf, u64 *val, int start, int end, + size_t len, enum packing_op op); + +#endif diff --git a/include/linux/dsa/sja1105.h b/include/linux/dsa/sja1105.h new file mode 100644 index 000000000000..abf3977e34fd --- /dev/null +++ b/include/linux/dsa/sja1105.h @@ -0,0 +1,23 @@ +/* SPDX-License-Identifier: GPL-2.0 + * Copyright (c) 2019, Vladimir Oltean <olteanv@gmail.com> + */ + +/* Included by drivers/net/dsa/sja1105/sja1105.h */ + +#ifndef _NET_DSA_SJA1105_H +#define _NET_DSA_SJA1105_H + +#include <linux/etherdevice.h> + +#define ETH_P_SJA1105 ETH_P_DSA_8021Q + +/* The switch can only be convinced to stay in unmanaged mode and not trap any + * link-local traffic by actually telling it to filter frames sent at the + * 00:00:00:00:00:00 destination MAC. + */ +#define SJA1105_LINKLOCAL_FILTER_A 0x000000000000ull +#define SJA1105_LINKLOCAL_FILTER_A_MASK 0xFFFFFFFFFFFFull +#define SJA1105_LINKLOCAL_FILTER_B 0x000000000000ull +#define SJA1105_LINKLOCAL_FILTER_B_MASK 0xFFFFFFFFFFFFull + +#endif /* _NET_DSA_SJA1105_H */ diff --git a/include/linux/packing.h b/include/linux/packing.h new file mode 100644 index 000000000000..54667735cc67 --- /dev/null +++ b/include/linux/packing.h @@ -0,0 +1,49 @@ +/* SPDX-License-Identifier: BSD-3-Clause + * Copyright (c) 2016-2018, NXP Semiconductors + * Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ +#ifndef _LINUX_PACKING_H +#define _LINUX_PACKING_H + +#include <linux/types.h> +#include <linux/bitops.h> + +#define QUIRK_MSB_ON_THE_RIGHT BIT(0) +#define QUIRK_LITTLE_ENDIAN BIT(1) +#define QUIRK_LSW32_IS_FIRST BIT(2) + +enum packing_op { + PACK, + UNPACK, +}; + +/** + * packing - Convert numbers (currently u64) between a packed and an unpacked + * format. Unpacked means laid out in memory in the CPU's native + * understanding of integers, while packed means anything else that + * requires translation. + * + * @pbuf: Pointer to a buffer holding the packed value. + * @uval: Pointer to an u64 holding the unpacked value. + * @startbit: The index (in logical notation, compensated for quirks) where + * the packed value starts within pbuf. Must be larger than, or + * equal to, endbit. + * @endbit: The index (in logical notation, compensated for quirks) where + * the packed value ends within pbuf. Must be smaller than, or equal + * to, startbit. + * @op: If PACK, then uval will be treated as const pointer and copied (packed) + * into pbuf, between startbit and endbit. + * If UNPACK, then pbuf will be treated as const pointer and the logical + * value between startbit and endbit will be copied (unpacked) to uval. + * @quirks: A bit mask of QUIRK_LITTLE_ENDIAN, QUIRK_LSW32_IS_FIRST and + * QUIRK_MSB_ON_THE_RIGHT. + * + * Return: 0 on success, EINVAL or ERANGE if called incorrectly. Assuming + * correct usage, return code may be discarded. + * If op is PACK, pbuf is modified. + * If op is UNPACK, uval is modified. + */ +int packing(void *pbuf, u64 *uval, int startbit, int endbit, size_t pbuflen, + enum packing_op op, u8 quirks); + +#endif diff --git a/include/uapi/linux/if_ether.h b/include/uapi/linux/if_ether.h index 3a45b4ad71a3..3158ba672b72 100644 --- a/include/uapi/linux/if_ether.h +++ b/include/uapi/linux/if_ether.h @@ -109,6 +109,7 @@ #define ETH_P_QINQ2 0x9200 /* deprecated QinQ VLAN [ NOT AN OFFICIALLY REGISTERED ID ] */ #define ETH_P_QINQ3 0x9300 /* deprecated QinQ VLAN [ NOT AN OFFICIALLY REGISTERED ID ] */ #define ETH_P_EDSA 0xDADA /* Ethertype DSA [ NOT AN OFFICIALLY REGISTERED ID ] */ +#define ETH_P_DSA_8021Q 0xDADB /* Fake VLAN Header for DSA [ NOT AN OFFICIALLY REGISTERED ID ] */ #define ETH_P_IFE 0xED3E /* ForCES inter-FE LFB type */ #define ETH_P_AF_IUCV 0xFBFB /* IBM af_iucv [ NOT AN OFFICIALLY REGISTERED ID ] */ diff --git a/lib/Kconfig b/lib/Kconfig index a9e56539bd11..ac1fcf06d8ea 100644 --- a/lib/Kconfig +++ b/lib/Kconfig @@ -18,6 +18,23 @@ config RAID6_PQ_BENCHMARK Benchmark all available RAID6 PQ functions on init and choose the fastest one. +config PACKING + bool "Generic bitfield packing and unpacking" + default n + help + This option provides the packing() helper function, which permits + converting bitfields between a CPU-usable representation and a + memory representation that can have any combination of these quirks: + - Is little endian (bytes are reversed within a 32-bit group) + - The least-significant 32-bit word comes first (within a 64-bit + group) + - The most significant bit of a byte is at its right (bit 0 of a + register description is numerically 2^7). + Drivers may use these helpers to match the bit indices as described + in the data sheets of the peripherals they are in control of. + + When in doubt, say N. + config BITREVERSE tristate diff --git a/lib/Makefile b/lib/Makefile index 3b08673e8881..7d4db18fabf1 100644 --- a/lib/Makefile +++ b/lib/Makefile @@ -108,6 +108,7 @@ obj-$(CONFIG_DEBUG_LIST) += list_debug.o obj-$(CONFIG_DEBUG_OBJECTS) += debugobjects.o obj-$(CONFIG_BITREVERSE) += bitrev.o +obj-$(CONFIG_PACKING) += packing.o obj-$(CONFIG_RATIONAL) += rational.o obj-$(CONFIG_CRC_CCITT) += crc-ccitt.o obj-$(CONFIG_CRC16) += crc16.o diff --git a/lib/packing.c b/lib/packing.c new file mode 100644 index 000000000000..50d1e9f2f5a7 --- /dev/null +++ b/lib/packing.c @@ -0,0 +1,213 @@ +// SPDX-License-Identifier: BSD-3-Clause OR GPL-2.0 +/* Copyright (c) 2016-2018, NXP Semiconductors + * Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ +#include <linux/packing.h> +#include <linux/module.h> +#include <linux/bitops.h> +#include <linux/errno.h> +#include <linux/types.h> + +static int get_le_offset(int offset) +{ + int closest_multiple_of_4; + + closest_multiple_of_4 = (offset / 4) * 4; + offset -= closest_multiple_of_4; + return closest_multiple_of_4 + (3 - offset); +} + +static int get_reverse_lsw32_offset(int offset, size_t len) +{ + int closest_multiple_of_4; + int word_index; + + word_index = offset / 4; + closest_multiple_of_4 = word_index * 4; + offset -= closest_multiple_of_4; + word_index = (len / 4) - word_index - 1; + return word_index * 4 + offset; +} + +static u64 bit_reverse(u64 val, unsigned int width) +{ + u64 new_val = 0; + unsigned int bit; + unsigned int i; + + for (i = 0; i < width; i++) { + bit = (val & (1 << i)) != 0; + new_val |= (bit << (width - i - 1)); + } + return new_val; +} + +static void adjust_for_msb_right_quirk(u64 *to_write, int *box_start_bit, + int *box_end_bit, u8 *box_mask) +{ + int box_bit_width = *box_start_bit - *box_end_bit + 1; + int new_box_start_bit, new_box_end_bit; + + *to_write >>= *box_end_bit; + *to_write = bit_reverse(*to_write, box_bit_width); + *to_write <<= *box_end_bit; + + new_box_end_bit = box_bit_width - *box_start_bit - 1; + new_box_start_bit = box_bit_width - *box_end_bit - 1; + *box_mask = GENMASK_ULL(new_box_start_bit, new_box_end_bit); + *box_start_bit = new_box_start_bit; + *box_end_bit = new_box_end_bit; +} + +/** + * packing - Convert numbers (currently u64) between a packed and an unpacked + * format. Unpacked means laid out in memory in the CPU's native + * understanding of integers, while packed means anything else that + * requires translation. + * + * @pbuf: Pointer to a buffer holding the packed value. + * @uval: Pointer to an u64 holding the unpacked value. + * @startbit: The index (in logical notation, compensated for quirks) where + * the packed value starts within pbuf. Must be larger than, or + * equal to, endbit. + * @endbit: The index (in logical notation, compensated for quirks) where + * the packed value ends within pbuf. Must be smaller than, or equal + * to, startbit. + * @op: If PACK, then uval will be treated as const pointer and copied (packed) + * into pbuf, between startbit and endbit. + * If UNPACK, then pbuf will be treated as const pointer and the logical + * value between startbit and endbit will be copied (unpacked) to uval. + * @quirks: A bit mask of QUIRK_LITTLE_ENDIAN, QUIRK_LSW32_IS_FIRST and + * QUIRK_MSB_ON_THE_RIGHT. + * + * Return: 0 on success, EINVAL or ERANGE if called incorrectly. Assuming + * correct usage, return code may be discarded. + * If op is PACK, pbuf is modified. + * If op is UNPACK, uval is modified. + */ +int packing(void *pbuf, u64 *uval, int startbit, int endbit, size_t pbuflen, + enum packing_op op, u8 quirks) +{ + /* Number of bits for storing "uval" + * also width of the field to access in the pbuf + */ + u64 value_width; + /* Logical byte indices corresponding to the + * start and end of the field. + */ + int plogical_first_u8, plogical_last_u8, box; + + /* startbit is expected to be larger than endbit */ + if (startbit < endbit) + /* Invalid function call */ + return -EINVAL; + + value_width = startbit - endbit + 1; + if (value_width > 64) + return -ERANGE; + + /* Check if "uval" fits in "value_width" bits. + * If value_width is 64, the check will fail, but any + * 64-bit uval will surely fit. + */ + if (op == PACK && value_width < 64 && (*uval >= (1ull << value_width))) + /* Cannot store "uval" inside "value_width" bits. + * Truncating "uval" is most certainly not desirable, + * so simply erroring out is appropriate. + */ + return -ERANGE; + + /* Initialize parameter */ + if (op == UNPACK) + *uval = 0; + + /* Iterate through an idealistic view of the pbuf as an u64 with + * no quirks, u8 by u8 (aligned at u8 boundaries), from high to low + * logical bit significance. "box" denotes the current logical u8. + */ + plogical_first_u8 = startbit / 8; + plogical_last_u8 = endbit / 8; + + for (box = plogical_first_u8; box >= plogical_last_u8; box--) { + /* Bit indices into the currently accessed 8-bit box */ + int box_start_bit, box_end_bit, box_addr; + u8 box_mask; + /* Corresponding bits from the unpacked u64 parameter */ + int proj_start_bit, proj_end_bit; + u64 proj_mask; + + /* This u8 may need to be accessed in its entirety + * (from bit 7 to bit 0), or not, depending on the + * input arguments startbit and endbit. + */ + if (box == plogical_first_u8) + box_start_bit = startbit % 8; + else + box_start_bit = 7; + if (box == plogical_last_u8) + box_end_bit = endbit % 8; + else + box_end_bit = 0; + + /* We have determined the box bit start and end. + * Now we calculate where this (masked) u8 box would fit + * in the unpacked (CPU-readable) u64 - the u8 box's + * projection onto the unpacked u64. Though the + * box is u8, the projection is u64 because it may fall + * anywhere within the unpacked u64. + */ + proj_start_bit = ((box * 8) + box_start_bit) - endbit; + proj_end_bit = ((box * 8) + box_end_bit) - endbit; + proj_mask = GENMASK_ULL(proj_start_bit, proj_end_bit); + box_mask = GENMASK_ULL(box_start_bit, box_end_bit); + + /* Determine the offset of the u8 box inside the pbuf, + * adjusted for quirks. The adjusted box_addr will be used for + * effective addressing inside the pbuf (so it's not + * logical any longer). + */ + box_addr = pbuflen - box - 1; + if (quirks & QUIRK_LITTLE_ENDIAN) + box_addr = get_le_offset(box_addr); + if (quirks & QUIRK_LSW32_IS_FIRST) + box_addr = get_reverse_lsw32_offset(box_addr, + pbuflen); + + if (op == UNPACK) { + u64 pval; + + /* Read from pbuf, write to uval */ + pval = ((u8 *)pbuf)[box_addr] & box_mask; + if (quirks & QUIRK_MSB_ON_THE_RIGHT) + adjust_for_msb_right_quirk(&pval, + &box_start_bit, + &box_end_bit, + &box_mask); + + pval >>= box_end_bit; + pval <<= proj_end_bit; + *uval &= ~proj_mask; + *uval |= pval; + } else { + u64 pval; + + /* Write to pbuf, read from uval */ + pval = (*uval) & proj_mask; + pval >>= proj_end_bit; + if (quirks & QUIRK_MSB_ON_THE_RIGHT) + adjust_for_msb_right_quirk(&pval, + &box_start_bit, + &box_end_bit, + &box_mask); + + pval <<= box_end_bit; + ((u8 *)pbuf)[box_addr] &= ~box_mask; + ((u8 *)pbuf)[box_addr] |= pval; + } + } + return 0; +} +EXPORT_SYMBOL(packing); + +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION("Generic bitfield packing and unpacking"); |