diff options
Diffstat (limited to 'include/asm-mips/sgi/hpc3.h')
| -rw-r--r-- | include/asm-mips/sgi/hpc3.h | 317 |
1 files changed, 0 insertions, 317 deletions
diff --git a/include/asm-mips/sgi/hpc3.h b/include/asm-mips/sgi/hpc3.h deleted file mode 100644 index c4729f531919..000000000000 --- a/include/asm-mips/sgi/hpc3.h +++ /dev/null @@ -1,317 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * hpc3.h: Definitions for SGI HPC3 controller - * - * Copyright (C) 1996 David S. Miller - * Copyright (C) 1998 Ralf Baechle - */ - -#ifndef _SGI_HPC3_H -#define _SGI_HPC3_H - -#include <linux/types.h> -#include <asm/page.h> - -/* An HPC DMA descriptor. */ -struct hpc_dma_desc { - u32 pbuf; /* physical address of data buffer */ - u32 cntinfo; /* counter and info bits */ -#define HPCDMA_EOX 0x80000000 /* last desc in chain for tx */ -#define HPCDMA_EOR 0x80000000 /* last desc in chain for rx */ -#define HPCDMA_EOXP 0x40000000 /* end of packet for tx */ -#define HPCDMA_EORP 0x40000000 /* end of packet for rx */ -#define HPCDMA_XIE 0x20000000 /* irq generated when at end of this desc */ -#define HPCDMA_XIU 0x01000000 /* Tx buffer in use by CPU. */ -#define HPCDMA_EIPC 0x00ff0000 /* SEEQ ethernet special xternal bytecount */ -#define HPCDMA_ETXD 0x00008000 /* set to one by HPC when packet tx'd */ -#define HPCDMA_OWN 0x00004000 /* Denotes ring buffer ownership on rx */ -#define HPCDMA_BCNT 0x00003fff /* size in bytes of this dma buffer */ - - u32 pnext; /* paddr of next hpc_dma_desc if any */ -}; - -/* The set of regs for each HPC3 PBUS DMA channel. */ -struct hpc3_pbus_dmacregs { - volatile u32 pbdma_bptr; /* pbus dma channel buffer ptr */ - volatile u32 pbdma_dptr; /* pbus dma channel desc ptr */ - u32 _unused0[0x1000/4 - 2]; /* padding */ - volatile u32 pbdma_ctrl; /* pbus dma channel control register has - * copletely different meaning for read - * compared with write */ - /* read */ -#define HPC3_PDMACTRL_INT 0x00000001 /* interrupt (cleared after read) */ -#define HPC3_PDMACTRL_ISACT 0x00000002 /* channel active */ - /* write */ -#define HPC3_PDMACTRL_SEL 0x00000002 /* little endian transfer */ -#define HPC3_PDMACTRL_RCV 0x00000004 /* direction is receive */ -#define HPC3_PDMACTRL_FLSH 0x00000008 /* enable flush for receive DMA */ -#define HPC3_PDMACTRL_ACT 0x00000010 /* start dma transfer */ -#define HPC3_PDMACTRL_LD 0x00000020 /* load enable for ACT */ -#define HPC3_PDMACTRL_RT 0x00000040 /* Use realtime GIO bus servicing */ -#define HPC3_PDMACTRL_HW 0x0000ff00 /* DMA High-water mark */ -#define HPC3_PDMACTRL_FB 0x003f0000 /* Ptr to beginning of fifo */ -#define HPC3_PDMACTRL_FE 0x3f000000 /* Ptr to end of fifo */ - - u32 _unused1[0x1000/4 - 1]; /* padding */ -}; - -/* The HPC3 SCSI registers, this does not include external ones. */ -struct hpc3_scsiregs { - volatile u32 cbptr; /* current dma buffer ptr, diagnostic use only */ - volatile u32 ndptr; /* next dma descriptor ptr */ - u32 _unused0[0x1000/4 - 2]; /* padding */ - volatile u32 bcd; /* byte count info */ -#define HPC3_SBCD_BCNTMSK 0x00003fff /* bytes to transfer from/to memory */ -#define HPC3_SBCD_XIE 0x00004000 /* Send IRQ when done with cur buf */ -#define HPC3_SBCD_EOX 0x00008000 /* Indicates this is last buf in chain */ - - volatile u32 ctrl; /* control register */ -#define HPC3_SCTRL_IRQ 0x01 /* IRQ asserted, either dma done or parity */ -#define HPC3_SCTRL_ENDIAN 0x02 /* DMA endian mode, 0=big 1=little */ -#define HPC3_SCTRL_DIR 0x04 /* DMA direction, 1=dev2mem 0=mem2dev */ -#define HPC3_SCTRL_FLUSH 0x08 /* Tells HPC3 to flush scsi fifos */ -#define HPC3_SCTRL_ACTIVE 0x10 /* SCSI DMA channel is active */ -#define HPC3_SCTRL_AMASK 0x20 /* DMA active inhibits PIO */ -#define HPC3_SCTRL_CRESET 0x40 /* Resets dma channel and external controller */ -#define HPC3_SCTRL_PERR 0x80 /* Bad parity on HPC3 iface to scsi controller */ - - volatile u32 gfptr; /* current GIO fifo ptr */ - volatile u32 dfptr; /* current device fifo ptr */ - volatile u32 dconfig; /* DMA configuration register */ -#define HPC3_SDCFG_HCLK 0x00001 /* Enable DMA half clock mode */ -#define HPC3_SDCFG_D1 0x00006 /* Cycles to spend in D1 state */ -#define HPC3_SDCFG_D2 0x00038 /* Cycles to spend in D2 state */ -#define HPC3_SDCFG_D3 0x001c0 /* Cycles to spend in D3 state */ -#define HPC3_SDCFG_HWAT 0x00e00 /* DMA high water mark */ -#define HPC3_SDCFG_HW 0x01000 /* Enable 16-bit halfword DMA accesses to scsi */ -#define HPC3_SDCFG_SWAP 0x02000 /* Byte swap all DMA accesses */ -#define HPC3_SDCFG_EPAR 0x04000 /* Enable parity checking for DMA */ -#define HPC3_SDCFG_POLL 0x08000 /* hd_dreq polarity control */ -#define HPC3_SDCFG_ERLY 0x30000 /* hd_dreq behavior control bits */ - - volatile u32 pconfig; /* PIO configuration register */ -#define HPC3_SPCFG_P3 0x0003 /* Cycles to spend in P3 state */ -#define HPC3_SPCFG_P2W 0x001c /* Cycles to spend in P2 state for writes */ -#define HPC3_SPCFG_P2R 0x01e0 /* Cycles to spend in P2 state for reads */ -#define HPC3_SPCFG_P1 0x0e00 /* Cycles to spend in P1 state */ -#define HPC3_SPCFG_HW 0x1000 /* Enable 16-bit halfword PIO accesses to scsi */ -#define HPC3_SPCFG_SWAP 0x2000 /* Byte swap all PIO accesses */ -#define HPC3_SPCFG_EPAR 0x4000 /* Enable parity checking for PIO */ -#define HPC3_SPCFG_FUJI 0x8000 /* Fujitsu scsi controller mode for faster dma/pio */ - - u32 _unused1[0x1000/4 - 6]; /* padding */ -}; - -/* SEEQ ethernet HPC3 registers, only one seeq per HPC3. */ -struct hpc3_ethregs { - /* Receiver registers. */ - volatile u32 rx_cbptr; /* current dma buffer ptr, diagnostic use only */ - volatile u32 rx_ndptr; /* next dma descriptor ptr */ - u32 _unused0[0x1000/4 - 2]; /* padding */ - volatile u32 rx_bcd; /* byte count info */ -#define HPC3_ERXBCD_BCNTMSK 0x00003fff /* bytes to be sent to memory */ -#define HPC3_ERXBCD_XIE 0x20000000 /* HPC3 interrupts cpu at end of this buf */ -#define HPC3_ERXBCD_EOX 0x80000000 /* flags this as end of descriptor chain */ - - volatile u32 rx_ctrl; /* control register */ -#define HPC3_ERXCTRL_STAT50 0x0000003f /* Receive status reg bits of Seeq8003 */ -#define HPC3_ERXCTRL_STAT6 0x00000040 /* Rdonly irq status */ -#define HPC3_ERXCTRL_STAT7 0x00000080 /* Rdonlt old/new status bit from Seeq */ -#define HPC3_ERXCTRL_ENDIAN 0x00000100 /* Endian for dma channel, little=1 big=0 */ -#define HPC3_ERXCTRL_ACTIVE 0x00000200 /* Tells if DMA transfer is in progress */ -#define HPC3_ERXCTRL_AMASK 0x00000400 /* Tells if ACTIVE inhibits PIO's to hpc3 */ -#define HPC3_ERXCTRL_RBO 0x00000800 /* Receive buffer overflow if set to 1 */ - - volatile u32 rx_gfptr; /* current GIO fifo ptr */ - volatile u32 rx_dfptr; /* current device fifo ptr */ - u32 _unused1; /* padding */ - volatile u32 reset; /* reset register */ -#define HPC3_ERST_CRESET 0x1 /* Reset dma channel and external controller */ -#define HPC3_ERST_CLRIRQ 0x2 /* Clear channel interrupt */ -#define HPC3_ERST_LBACK 0x4 /* Enable diagnostic loopback mode of Seeq8003 */ - - volatile u32 dconfig; /* DMA configuration register */ -#define HPC3_EDCFG_D1 0x0000f /* Cycles to spend in D1 state for PIO */ -#define HPC3_EDCFG_D2 0x000f0 /* Cycles to spend in D2 state for PIO */ -#define HPC3_EDCFG_D3 0x00f00 /* Cycles to spend in D3 state for PIO */ -#define HPC3_EDCFG_WCTRL 0x01000 /* Enable writes of desc into ex ctrl port */ -#define HPC3_EDCFG_FRXDC 0x02000 /* Clear eop stat bits upon rxdc, hw seeq fix */ -#define HPC3_EDCFG_FEOP 0x04000 /* Bad packet marker timeout enable */ -#define HPC3_EDCFG_FIRQ 0x08000 /* Another bad packet timeout enable */ -#define HPC3_EDCFG_PTO 0x30000 /* Programmed timeout value for above two */ - - volatile u32 pconfig; /* PIO configuration register */ -#define HPC3_EPCFG_P1 0x000f /* Cycles to spend in P1 state for PIO */ -#define HPC3_EPCFG_P2 0x00f0 /* Cycles to spend in P2 state for PIO */ -#define HPC3_EPCFG_P3 0x0f00 /* Cycles to spend in P3 state for PIO */ -#define HPC3_EPCFG_TST 0x1000 /* Diagnistic ram test feature bit */ - - u32 _unused2[0x1000/4 - 8]; /* padding */ - - /* Transmitter registers. */ - volatile u32 tx_cbptr; /* current dma buffer ptr, diagnostic use only */ - volatile u32 tx_ndptr; /* next dma descriptor ptr */ - u32 _unused3[0x1000/4 - 2]; /* padding */ - volatile u32 tx_bcd; /* byte count info */ -#define HPC3_ETXBCD_BCNTMSK 0x00003fff /* bytes to be read from memory */ -#define HPC3_ETXBCD_ESAMP 0x10000000 /* if set, too late to add descriptor */ -#define HPC3_ETXBCD_XIE 0x20000000 /* Interrupt cpu at end of cur desc */ -#define HPC3_ETXBCD_EOP 0x40000000 /* Last byte of cur buf is end of packet */ -#define HPC3_ETXBCD_EOX 0x80000000 /* This buf is the end of desc chain */ - - volatile u32 tx_ctrl; /* control register */ -#define HPC3_ETXCTRL_STAT30 0x0000000f /* Rdonly copy of seeq tx stat reg */ -#define HPC3_ETXCTRL_STAT4 0x00000010 /* Indicate late collision occurred */ -#define HPC3_ETXCTRL_STAT75 0x000000e0 /* Rdonly irq status from seeq */ -#define HPC3_ETXCTRL_ENDIAN 0x00000100 /* DMA channel endian mode, 1=little 0=big */ -#define HPC3_ETXCTRL_ACTIVE 0x00000200 /* DMA tx channel is active */ -#define HPC3_ETXCTRL_AMASK 0x00000400 /* Indicates ACTIVE inhibits PIO's */ - - volatile u32 tx_gfptr; /* current GIO fifo ptr */ - volatile u32 tx_dfptr; /* current device fifo ptr */ - u32 _unused4[0x1000/4 - 4]; /* padding */ -}; - -struct hpc3_regs { - /* First regs for the PBUS 8 dma channels. */ - struct hpc3_pbus_dmacregs pbdma[8]; - - /* Now the HPC scsi registers, we get two scsi reg sets. */ - struct hpc3_scsiregs scsi_chan0, scsi_chan1; - - /* The SEEQ hpc3 ethernet dma/control registers. */ - struct hpc3_ethregs ethregs; - - /* Here are where the hpc3 fifo's can be directly accessed - * via PIO accesses. Under normal operation we never stick - * our grubby paws in here so it's just padding. */ - u32 _unused0[0x18000/4]; - - /* HPC3 irq status regs. Due to a peculiar bug you need to - * look at two different register addresses to get at all of - * the status bits. The first reg can only reliably report - * bits 4:0 of the status, and the second reg can only - * reliably report bits 9:5 of the hpc3 irq status. I told - * you it was a peculiar bug. ;-) - */ - volatile u32 istat0; /* Irq status, only bits <4:0> reliable. */ -#define HPC3_ISTAT_PBIMASK 0x0ff /* irq bits for pbus devs 0 --> 7 */ -#define HPC3_ISTAT_SC0MASK 0x100 /* irq bit for scsi channel 0 */ -#define HPC3_ISTAT_SC1MASK 0x200 /* irq bit for scsi channel 1 */ - - volatile u32 gio_misc; /* GIO misc control bits. */ -#define HPC3_GIOMISC_ERTIME 0x1 /* Enable external timer real time. */ -#define HPC3_GIOMISC_DENDIAN 0x2 /* dma descriptor endian, 1=lit 0=big */ - - u32 eeprom; /* EEPROM data reg. */ -#define HPC3_EEPROM_EPROT 0x01 /* Protect register enable */ -#define HPC3_EEPROM_CSEL 0x02 /* Chip select */ -#define HPC3_EEPROM_ECLK 0x04 /* EEPROM clock */ -#define HPC3_EEPROM_DATO 0x08 /* Data out */ -#define HPC3_EEPROM_DATI 0x10 /* Data in */ - - volatile u32 istat1; /* Irq status, only bits <9:5> reliable. */ - volatile u32 bestat; /* Bus error interrupt status reg. */ -#define HPC3_BESTAT_BLMASK 0x000ff /* Bus lane where bad parity occurred */ -#define HPC3_BESTAT_CTYPE 0x00100 /* Bus cycle type, 0=PIO 1=DMA */ -#define HPC3_BESTAT_PIDSHIFT 9 -#define HPC3_BESTAT_PIDMASK 0x3f700 /* DMA channel parity identifier */ - - u32 _unused1[0x14000/4 - 5]; /* padding */ - - /* Now direct PIO per-HPC3 peripheral access to external regs. */ - volatile u32 scsi0_ext[256]; /* SCSI channel 0 external regs */ - u32 _unused2[0x7c00/4]; - volatile u32 scsi1_ext[256]; /* SCSI channel 1 external regs */ - u32 _unused3[0x7c00/4]; - volatile u32 eth_ext[320]; /* Ethernet external registers */ - u32 _unused4[0x3b00/4]; - - /* Per-peripheral device external registers and DMA/PIO control. */ - volatile u32 pbus_extregs[16][256]; - volatile u32 pbus_dmacfg[8][128]; - /* Cycles to spend in D3 for reads */ -#define HPC3_DMACFG_D3R_MASK 0x00000001 -#define HPC3_DMACFG_D3R_SHIFT 0 - /* Cycles to spend in D4 for reads */ -#define HPC3_DMACFG_D4R_MASK 0x0000001e -#define HPC3_DMACFG_D4R_SHIFT 1 - /* Cycles to spend in D5 for reads */ -#define HPC3_DMACFG_D5R_MASK 0x000001e0 -#define HPC3_DMACFG_D5R_SHIFT 5 - /* Cycles to spend in D3 for writes */ -#define HPC3_DMACFG_D3W_MASK 0x00000200 -#define HPC3_DMACFG_D3W_SHIFT 9 - /* Cycles to spend in D4 for writes */ -#define HPC3_DMACFG_D4W_MASK 0x00003c00 -#define HPC3_DMACFG_D4W_SHIFT 10 - /* Cycles to spend in D5 for writes */ -#define HPC3_DMACFG_D5W_MASK 0x0003c000 -#define HPC3_DMACFG_D5W_SHIFT 14 - /* Enable 16-bit DMA access mode */ -#define HPC3_DMACFG_DS16 0x00040000 - /* Places halfwords on high 16 bits of bus */ -#define HPC3_DMACFG_EVENHI 0x00080000 - /* Make this device real time */ -#define HPC3_DMACFG_RTIME 0x00200000 - /* 5 bit burst count for DMA device */ -#define HPC3_DMACFG_BURST_MASK 0x07c00000 -#define HPC3_DMACFG_BURST_SHIFT 22 - /* Use live pbus_dreq unsynchronized signal */ -#define HPC3_DMACFG_DRQLIVE 0x08000000 - volatile u32 pbus_piocfg[16][64]; - /* Cycles to spend in P2 state for reads */ -#define HPC3_PIOCFG_P2R_MASK 0x00001 -#define HPC3_PIOCFG_P2R_SHIFT 0 - /* Cycles to spend in P3 state for reads */ -#define HPC3_PIOCFG_P3R_MASK 0x0001e -#define HPC3_PIOCFG_P3R_SHIFT 1 - /* Cycles to spend in P4 state for reads */ -#define HPC3_PIOCFG_P4R_MASK 0x001e0 -#define HPC3_PIOCFG_P4R_SHIFT 5 - /* Cycles to spend in P2 state for writes */ -#define HPC3_PIOCFG_P2W_MASK 0x00200 -#define HPC3_PIOCFG_P2W_SHIFT 9 - /* Cycles to spend in P3 state for writes */ -#define HPC3_PIOCFG_P3W_MASK 0x03c00 -#define HPC3_PIOCFG_P3W_SHIFT 10 - /* Cycles to spend in P4 state for writes */ -#define HPC3_PIOCFG_P4W_MASK 0x3c000 -#define HPC3_PIOCFG_P4W_SHIFT 14 - /* Enable 16-bit PIO accesses */ -#define HPC3_PIOCFG_DS16 0x40000 - /* Place even address bits in bits <15:8> */ -#define HPC3_PIOCFG_EVENHI 0x80000 - - /* PBUS PROM control regs. */ - volatile u32 pbus_promwe; /* PROM write enable register */ -#define HPC3_PROM_WENAB 0x1 /* Enable writes to the PROM */ - - u32 _unused5[0x0800/4 - 1]; - volatile u32 pbus_promswap; /* Chip select swap reg */ -#define HPC3_PROM_SWAP 0x1 /* invert GIO addr bit to select prom0 or prom1 */ - - u32 _unused6[0x0800/4 - 1]; - volatile u32 pbus_gout; /* PROM general purpose output reg */ -#define HPC3_PROM_STAT 0x1 /* General purpose status bit in gout */ - - u32 _unused7[0x1000/4 - 1]; - volatile u32 rtcregs[14]; /* Dallas clock registers */ - u32 _unused8[50]; - volatile u32 bbram[8192-50-14]; /* Battery backed ram */ -}; - -/* - * It is possible to have two HPC3's within the address space on - * one machine, though only having one is more likely on an Indy. - */ -extern struct hpc3_regs *hpc3c0, *hpc3c1; -#define HPC3_CHIP0_BASE 0x1fb80000 /* physical */ -#define HPC3_CHIP1_BASE 0x1fb00000 /* physical */ - -extern void sgihpc_init(void); - -#endif /* _SGI_HPC3_H */ |