| Age | Commit message (Collapse) | Author |
|---|
|
The commit 55ee7017ee31 ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x") unintentionally changes the
clocksource devices for AM437x from OMAP GP Timer to SyncTimer32K.
Unfortunately, the SyncTimer32K is starving from frequency deviation
as mentioned in commit 5b5c01359152 ("ARM: OMAP2+: AM43x: Use gptimer
as clocksource") and, as reported by Franklin [1], even its monotonic
nature is under question (most probably there is a HW issue, but it's
still under investigation).
Taking into account above facts It's reasonable to rollback to the use
of omap3_gptimer_timer_init().
[1] http://www.spinics.net/lists/linux-omap/msg127425.html
Fixes: 55ee7017ee31 ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x")
Reported-by: Cooper Jr., Franklin <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2, this
is an new variant of the the DRA72x/DRA74x automotive infotainment
chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7 based
microcontroller we support, related to the smaller STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile, see
http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to removing
support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the memory
controller using 'perf'"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (95 commits)
ARM: davinci: da830-evm: use gpio descriptor for mmc pins
ARM: davinci: da850-evm: use gpio descriptor for mmc pins
ARM: davinci: hawk: use gpio descriptor for mmc pins
ARM: ARTPEC-6: add select MFD_SYSCON to MACH_ARTPEC6
ARM: davinci: da8xx: Fix ohci device name
ARM: oxnas: Add OX820 config and makefile entry
ARM: oxnas: Add OX820 SMP support
ARM: davinci: PM: fix build when da850 not compiled in
ARM: orion5x: remove legacy support of ls-chl
ARM: integrator: drop EBI access use syscon
ARM: BCM5301X: Add back handler ignoring external imprecise aborts
ARM: davinci: PM: support da8xx DT platforms
ARM: davinci: PM: cleanup: remove references to pdata
ARM: davinci: PM: rework init, remove platform device
ARM: Kconfig: Introduce MACH_STM32F746 flag
ARM: mach-stm32: Add a new SOC - STM32F746
ARM: shmobile: document SK-RZG1E board
ARM: shmobile: r8a7745: basic SoC support
ARM: imx: mach-imx6ul: add imx6ull support
ARM: zynq: Reserve correct amount of non-DMA RAM
...
|
|
DRA71x processor family is a derivative of DRA722 ES2.0 targetted for
infotainment systems.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The function is empty, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This fixed a regression with DT boot compared to legacy boot.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
[tony@atomide.com: edited patch subject to follow standard]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This fixes a regression with device tree based booting compared to legacy booting for n900 to make the n900 legacy user space to also work with device tree based booting
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
|
|
AM437x-based boards, can use omap4_local_timer_init()
just fine. Let's use that instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Some omaps are producing imprecise external aborts because we are
wrongly trying to init SRAM for device tree based booting. Only
omap3 is still using the legacy SRAM code, so we need to make it
omap3 specific. Otherwise we can get errors like this on at least
dm814x:
Unhandled fault: imprecise external abort (0xc06) at 0xc08b156c
...
(omap_rev) from [<c08b12e0>] (omap_sram_init+0xf8/0x3e0)
(omap_sram_init) from [<c08aca0c>] (omap_sdrc_init+0x10/0xb0)
(omap_sdrc_init) from [<c08b581c>] (pdata_quirks_init+0x18/0x44)
(pdata_quirks_init) from [<c08b5478>] (omap_generic_init+0x10/0x1c)
(omap_generic_init) from [<c08a57e0>] (customize_machine+0x1c/0x40)
(customize_machine) from [<c00098a4>] (do_one_initcall+0x80/0x1dc)
(do_one_initcall) from [<c08a2ec4>] (kernel_init_freeable+0x218/0x2e8)
(kernel_init_freeable) from [<c063a554>] (kernel_init+0x8/0xec)
(kernel_init) from [<c000f890>] (ret_from_fork+0x14/0x24)
Let's fix the issue by making sure omap_sdrc_init only gets called for
omap3. To do that, we need to have compatible "ti,omap3" in the dts
files. And let's also use "ti,omap3630" instead of "ti,omap36xx" like
we're supposed to.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On boards with more than 2GB of RAM booting goes wrong with things not
working and we're getting lots of l3 warnings:
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x260/0x384()
44000000.ocp:L3 Custom Error: MASTER MMC6 TARGET DMM1 (Idle):
Data Access in User mode during Functional access
...
[<c044e158>] (scsi_add_host_with_dma) from [<c04705c8>]
(ata_scsi_add_hosts+0x5c/0x18c)
[<c04705c8>] (ata_scsi_add_hosts) from [<c046b13c>]
(ata_host_register+0x150/0x2cc)
[<c046b13c>] (ata_host_register) from [<c046b38c>]
(ata_host_activate+0xd4/0x124)
[<c046b38c>] (ata_host_activate) from [<c047f42c>]
(ahci_host_activate+0x5c/0x194)
[<c047f42c>] (ahci_host_activate) from [<c0480854>]
(ahci_platform_init_host+0x1f0/0x3f0)
[<c0480854>] (ahci_platform_init_host) from [<c047c9dc>]
(ahci_probe+0x70/0x98)
[<c047c9dc>] (ahci_probe) from [<c04220cc>]
(platform_drv_probe+0x54/0xb4)
Let's fix the issue by enabling ZONE_DMA for LPAE. Note that we need to
limit dma_zone_size to 2GB as the rest of the RAM is beyond the 4GB limit.
Let's also fix things for dra7 as done in similar patches in the TI tree
by Lokesh Vutla <lokeshvutla@ti.com>.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
this function is not only about the 32k sync
timer, it's OMAP's generic init_time implementation.
Let's rename it to make that detail easier to
notice.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
instead of constantly defining a small wrapper
around __omap_sync32k_timer_init(), let's define
a generic one which can be used by all OMAPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When commit c4082d499fa2 ("ARM: omap2+: board-generic: clean up the
irq data from board file") cleaned up the direct usage of gic_of_init
and omap_intc_of_init, it failed to clean up the macros properly.
Since these macros are no longer used, lets just remove them.
Fixes: c4082d499fa2 ("ARM: omap2+: board-generic: clean up the irq data from board file")
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Update dm814x changes for sparse fixes to make data structures
static.
Conflicts:
arch/arm/mach-omap2/omap_hwmod_81xx_data.c
|
|
Fix dm814x DT_MACHINE_START.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DRA7 uses OMAP5 IO table at the moment. This is purely spurious since
the OMAP5 and DRA7 register maps are different in many aspects.
AM57xx/DRA7 TRM Reference: http://www.ti.com/lit/ug/spruhz6/spruhz6.pdf
NOTE: Most of the drivers are already doing ioremap, so, there should'nt
be any functional improvement involved here, other than making the
initial iotable more accurate.
Fixes: a3a9384a1157 ("ARM: DRA7: Reuse io tables and add a new .init_early")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Also included are some cleanups where
the platform maintainers hadn't separated cleanups from new developent
in separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might
start combining the cleanup and new-development branches more"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (124 commits)
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: digicolor: select syscon and timer
ARM: zynq: Simplify SLCR initialization
ARM: zynq: PM: Fixed simple typo.
ARM: zynq: Setup default gpio number for Xilinx Zynq
ARM: digicolor: add low level debug support
ARM: initial support for Conexant Digicolor CX92755 SoC
ARM: OMAP2+: Add dm816x hwmod support
ARM: OMAP2+: Add clock domain support for dm816x
ARM: OMAP2+: Add board-generic.c entry for ti81xx
ARM: at91: pm: remove warning to remove SOC_AT91SAM9263 usage
ARM: at91: remove unused mach/system_rev.h
ARM: at91: stop using HAVE_AT91_DBGUx
ARM: at91: fix ordering of SRAM and PM initialization
...
|
|
Pull ARM updates from Russell King:
- clang assembly fixes from Ard
- optimisations and cleanups for Aurora L2 cache support
- efficient L2 cache support for secure monitor API on Exynos SoCs
- debug menu cleanup from Daniel Thompson to allow better behaviour for
multiplatform kernels
- StrongARM SA11x0 conversion to irq domains, and pxa_timer
- kprobes updates for older ARM CPUs
- move probes support out of arch/arm/kernel to arch/arm/probes
- add inline asm support for the rbit (reverse bits) instruction
- provide an ARM mode secondary CPU entry point (for Qualcomm CPUs)
- remove the unused ARMv3 user access code
- add driver_override support to AMBA Primecell bus
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (55 commits)
ARM: 8256/1: driver coamba: add device binding path 'driver_override'
ARM: 8301/1: qcom: Use secondary_startup_arm()
ARM: 8302/1: Add a secondary_startup that assumes ARM mode
ARM: 8300/1: teach __asmeq that r11 == fp and r12 == ip
ARM: kprobes: Fix compilation error caused by superfluous '*'
ARM: 8297/1: cache-l2x0: optimize aurora range operations
ARM: 8296/1: cache-l2x0: clean up aurora cache handling
ARM: 8284/1: sa1100: clear RCSR_SMR on resume
ARM: 8283/1: sa1100: collie: clear PWER register on machine init
ARM: 8282/1: sa1100: use handle_domain_irq
ARM: 8281/1: sa1100: move GPIO-related IRQ code to gpio driver
ARM: 8280/1: sa1100: switch to irq_domain_add_simple()
ARM: 8279/1: sa1100: merge both GPIO irqdomains
ARM: 8278/1: sa1100: split irq handling for low GPIOs
ARM: 8291/1: replace magic number with PAGE_SHIFT macro in fixup_pv code
ARM: 8290/1: decompressor: fix a wrong comment
ARM: 8286/1: mm: Fix dma_contiguous_reserve comment
ARM: 8248/1: pm: remove outdated comment
ARM: 8274/1: Fix DEBUG_LL for multi-platform kernels (without PL01X)
ARM: 8273/1: Seperate DEBUG_UART_PHYS from DEBUG_LL on EP93XX
...
|
|
This allows booting ti81xx boards when a .dts file
is in place.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch implements generic DT L2C initialisation (the one from
init_IRQ in arch/arm/kernel/irq.c) for Omap4 and AM43 platforms and
kills the SoC specific stuff in arch/arm/mach-omap2/omap4-common.c.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
N900 legacy user space apps need the board name in
/proc/cpuinfo to work properly for the Hardware entry.
For other boards this should not be an issues and they
can use the generic Hardware entry.
Let's fix the issue by adding a custom DT_MACHINE_START
for n900.
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into
drivers directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
bus: arm-ccn: Fix spurious warning message
leds: add device tree bindings for register bit LEDs
soc: add driver for the ARM RealView
power: reset: driver for the Versatile syscon reboot
leds: add a driver for syscon-based LEDs
drivers/soc: ti: fix build break with modules
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, this is the largest branch, though this time a little under
half of the total changes with 307 individual non-merge changesets.
The largest changes are the addition of new machines, in particular
the Tegra based Chromebook, the Renesas r8a7794 SoC, and DT support
for the old i.MX1 platform.
Other changes include
- at91: various sam9 and sama5 updates
- exynos: much extended Peach Pi/Pit (Chromebook 2) support
- keystone: new peripherals
- meson: added DT for meson6 SoC
- mvebu: new device support for Armada 370/375
- qcom: improved support for IPQ8064 and MSM8x60
- rockchip: much improved support for rk3288
- shmobile: lots of updates all over the place
- sunxi: dts license change
- sunxi: more a23 device support
- vexpress: CLCD DT description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (308 commits)
ARM: DTS: meson: update DTSI to add watchdog node
ARM: dts: keystone-k2l: fix mdio io start address
ARM: dts: keystone-k2e: fix mdio io start address
ARM: dts: keystone-k2e: update usb1 node for dma properties
ARM: dts: keystone: fix io range for usb_phy0
Revert "Merge tag 'hix5hd2-dt-for-3.18' of git://github.com/hisilicon/linux-hisi into next/dt"
Revert "ARM: dts: hix5hd2: add wdg node"
ARM: dts: add rk3288 i2s controller
ARM: vexpress: Add CLCD Device Tree properties
ARM: bcm2835: add I2S pinctrl to device tree
ARM: meson: documentation: add bindings documentation
ARM: meson: dts: add basic Meson/Meson6/Meson6-atv1200 DTSI/DTS
ARM: dts: mt6589: Change compatible string for GIC
ARM: dts: mediatek: Add compatible property for aquaris5
ARM: dts: mt6589-aquaris5: Add boot argument earlyprintk
ARM: dts: mt6589: Fix typo in GIC unit address
ARM: dts: Build dtb for Mediatek board
ARM: dts: keystone: fix bindings for pcie and usb clock nodes
ARM: dts: keystone: k2l: Fix chip selects for SPI devices
ARM: dts: keystone: add dsp gpio controllers nodes
...
|
|
now we can safely drop those fields from our machine_desc.
While at that, also drop the now unused omap_intc_of_init()
definition.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. So mark the
non-const function parameters and structs for OMAP2+ as const, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The definition
static const char *omap3_boards_compat[] __initconst = {
defines a changable array of constant strings. That is you must not do:
*omap3_boards_compat[0] = 'f';
but
omap3_boards_compat[0] = "another string";
is fine. So the annotation __initconst is wrong and yields a compiler
error when other really const variables are added with __initconst.
As the struct machine_desc member dt_compat is declared as
const char *const *dt_compat;
making the arrays const is the better alternative over changing all
annotations to __initdata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM57xx processor family are variants of DRA7 family of processors and
targetted at industrial and non-automotive applications.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The only difference from the dra74x devices is the missing .smp entry.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use of const init definition must use __initconst so replace
all such instances where __initdata is used.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull OMAP fbdev changes from Tomi Valkeinen:
"This is based on the already pulled fbdev-main changes, and this also
merges .dts branch from Tony Lindgren (which has also been pulled), so
that I was able to add the display related .dts changes.
This contains OMAP related fbdev changes for 3.15. The bulk of the
patches are for adding Device Tree support for OMAP Display Subsystem:
- SoCs: OMAP2/3/4
- Boards: OMAP4 Panda, OMAP4 SDP, OMAP3 Beagle, OMAP3 Beagle-xM,
OMAP3 IGEP0020, OMAP3 N900
- Devices: TFP410 Encoder, tpd12s015 HDMI companion chip, Sony
acx565akm panel, MIPI DSI Command mode panel and HDMI, DVI and
Analog TV connectors"
* tag 'fbdev-omap-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (45 commits)
OMAPDSS: HDMI: fix interlace output
OMAPDSS: add missing __init for dss_init_ports
ARM: OMAP2+: remove pdata quirks for displays
OMAPDSS: remove DT hacks for regulators
Doc/DT: Add DT binding documentation for tpd12s015 encoder
Doc/DT: Add DT binding documentation for TFP410 encoder
Doc/DT: Add DT binding documentation for Sony acx565akm panel
Doc/DT: Add DT binding documentation for MIPI DSI CM Panel
Doc/DT: Add DT binding documentation for HDMI Connector
Doc/DT: Add DT binding documentation for DVI Connector
Doc/DT: Add DT binding documentation for Analog TV Connector
ARM: omap3-n900.dts: add display information
ARM: omap3-igep0020.dts: add display information
ARM: omap3-beagle-xm.dts: add display information
ARM: omap3-beagle.dts: add display information
ARM: omap4-sdp.dts: add display information
Doc/DT: Add DT binding documentation for OMAP DSS
OMAPDSS: acx565akm: Add DT support
OMAPDSS: connector-analog-tv: Add DT support
OMAPDSS: hdmi-connector: Add DT support
...
|
|
As there is no common panel framework in the kernel, we have OMAP
specific panel drivers. However, the DT data should be generic. This
brings the issue that some other platform could use the same panels, and
would need to create a driver with the same 'compatible' string as the
OMAP driver.
In the long run, we have to get a common panel framework. For the time
being, this patch solves the issue:
At early boot time, we go through the DT nodes looking for the panels
the kernel supports for OMAP. For each found node, the 'compatible'
string is prepended with "omapdss,", i.e. "sony,acx565akm" becomes
"omapdss,sony,acx565akm". The OMAP display drivers all have "omapdss,"
at the beginning of their compatible field.
This allows us to have generic DT data, but OMAP specific display
drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The OMAP display architecture requires a bunch of platform devices which
are not created via .dts (for now). We also need to pass a few function
pointers and the DSS hardware version from the arch code to omapdss
driver.
This patch adds omapdss_init_of() function, called from board-generic at
init time, which handles those tasks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Power, reset and clock related changes via Paul Walmsley <paul@pwsan.com>, via
Tony Lindgren:
Some low-level optimizations and fixes that don't belong in an -rc
series for various OMAP-family chips, targeted for v3.15.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/prcm-a-for-v3.15/20140228124518/
* tag 'omap-for-v3.15/prcm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: DPLL: stop reparenting to same parent if already done
ARM: OMAP2+: clock: fix rate prints
ARM: AM43x: hwmod data: register spinlock OCP interface
ARM: OMAP2+: clockdomain: Reintroduce SW_SLEEP Support
ARM: OMAP2+: AM43xx: implement support for machine restart
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The SyncTimer in AM43x is clocked using the following two sources:
1) An inaccuarte 32k clock (CLK_32KHZ) derived from PER DPLL, causing system
time to go slowly (~10% deviation).
2) external 32KHz RTC clock, which may not always be available on board like
in the case of ePOS EVM
Use gptimer as clocksource instead, as is done in the case of AM335x
(which does not have a SyncTimer). With this, system time keeping works
accurately.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add restart hook so that AM4372 builds can restart the platform.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Now that we have standardized SoC definitions, update the
compatibility strings in board machine descriptors. Eventually, we
should just have SoC compatiblity here and all board specific stuff
should disappear.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The am3517 is wrongly booting as omap3 which means that the am3517
specific devices like Ethernet won't work when booted with device
tree. Now with the new devices defined in am3517.dtsi, let's use
that instead of the omap3.dtsi, and add a separate machine entry
for am3517 so am3517-evm can use it.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated comments and fixed build without omap3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM335x, AM43xx, OMAP5 and DRA7 have missing late init hook. Introduce
SoC specific hook with a call to OMAP2+ generic lateinit hook. This
allows the generic late initializations such as cpufreq hooks to be
active.
Based on out-of-tree patches that need to be introduced in
mainline, this introduction allows us to provide the foundation for
further SoC specific features as they are developed.
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
omap-for-v3.13/board-removal
We need the fixes in v3.12-rc5, dts changes in omap-for-v3.13/dt, and
the platform data quirk changes in omap-for-v3.13/quirk to start
removing omap3 board files without breaking things.
|
|
For few things we're still going to be needing platform
data for device tree based drivers. Let's set up auxdata
handling and do it in pdata-quirks.c so we have all the
legacy calls in one place.
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
SoC family definitions at the moment are reactive to board needs
as a result, beagle-xm would matchup with ti,omap3 which invokes
omap3430_init_early instead of omap3630_init_early. Obviously, this is
the wrong behavior.
With clock node dts conversion, we get the following warnings before
system hangs as a result and 3630 based platforms fails to boot
(uart4 clocks are only present in OMAP3630 and not present in
OMAP3430):
...
omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
omap_hwmod: uart4: cannot _init_clocks
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434
_init+0x6c/0x80()
omap_hwmod: uart4: couldn't init clocks
...
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: timer12: enabled state can only be entered from
initialized, idle, or disabled state
...
WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224
_idle+0xd4/0xf8()
omap_hwmod: timer12: idle state can only be entered from enabled state
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: uart4: enabled state can only be entered from
initialized, idle, or disabled state
So, add specific compatiblity for 3630 to allow match for Beagle-XM
platform.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: left out ti,omap343x, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Let's use platform data quirk support for board-generic.c.
This removes all board specific hacks out of board-generic.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We want to drop the board-*.c files but keep things working.
Let's make it a bit easier to support legacy platform data
init with quirks. This also keeps board-generic.c clean from
board specific hacks.
For now, the quirks table is empty, that is populated
in the later patches.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The omap44xx_restart used on omap4 and omap5 devices can be reused
on dra7 devices as well. The device instance however is different
across omap5 and dra7 as compared to omap4. So fix this for omap5
as well as dra7.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Describe minimal DT boot machine details for DRA7xx based SoC's. DRA7xx
family is based on dual core ARM CORTEX A15 using GIC as the interrupt controller.
The PRCM and timer infrastructure is reused from OMAP5 and so are the io
descriptor tables.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
|
|
Till the OMAP clocks are correctly defined in device tree, use
this temporary hack to provide clock alias to the USB PHY clocks.
Without this, USB Host & Ethernet will not be functional with
device tree boots on Panda and uEVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Describe minimal DT boot machine details for AM43x based SoC's. AM43x
SoC's are ARM Cortex-A9 based with one core. AM43x is similar to
AM335x w.r.t L4 PER/WKUP memory map. AM43x has a sync timer, here that
is being used as clocksource, while 1ms dmtimer as clockevent.
Signed-off-by: Ankur Kishore <a-kishore@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
|
|
DevKit8000 is a beagle board clone from Timll, sold by
armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D,
S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and
JTAG interface.
Add the basic DT support for devkit8000. It includes:
- twl4030 (PMIC)
- MMC1
- I2C1
- leds
Signed-off-by: Anil Kumar <anilk4.v@gmail.com>
Tested-by: Thomas Weber <thomas@tomweber.eu>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
omap-for-v3.10/timer
Conflicts:
arch/arm/mach-omap2/timer.c
|
