| Age | Commit message (Collapse) | Author |
|---|
|
This define should really be TX_CMD_SEC_KEY_FROM_TABLE
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
FW versions older than -17 for 3160 and 7260 and older than -22 for
newer NICs are not supported anymore. Don't load these versions
and remove code that handles them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support new format. TX response will not be sent anymore,
so all needed data is in the BA response.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Due to the addition of another option in the SCD_CONFIG_CMD's
%enable field, change the assignment of this field to use
defines rather than hard-code the value itself.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Newer hardware supports GCMP and GCMP 256-bit ciphers.
Add support for adding/setting GCMP key for TX mode.
In the TX command handling GCMP-256 is handled in a different
way as the key size should be up to 128-bits:
Set the key value to the key index in the key table,
and specify that this key should be taken form the key table
instead of from the TX command.
While at it - convert security control flags to an enum.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add support CSA countdown offloading. When CSA starts, the driver
specifies the offsets to the eCSA and CSA IEs in the beacon template
command and the fw performs the countdown.
The fw notifies the driver when the channel switch flow
should be performed.
Beacon sent notifications are not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
TX CMD API has changed to support offload assist.
Currently we do not enable checksum yet, but must set the
padding indication, to avoid FW errors.
Set other amsdu flag as well.
The rest of the flags will be configured only if HW csum
is enabled and will be set in future patches.
This change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
FW behaviour changed and now updates driver about the used TPC
reduction in the following cases:
1. In tx response, which is used mostly for a single frame case
2. In BA notification
When tx aggregation fails with the initial rate, FW will send
to the driver BA notification and will try to transmit with the
next rate, but this time without tx power reduction. Thus, in case
of a failure with the initial rate, driver will get two BA notifications,
the first one with reduced tx power as in the LQ command and the second
one with 0 power reduction.
This patch adapts the TPC statistics according to the description above:
1. Use BA notifications instead of Tx response
2. For TPC only, drop the optimization which considers empty BA as one
MPDU. The reason is that with TPC we want to recover very quickly from
a bad power reduction and, therefore we'd like the success ratio to get
an immediate hit when failing to get a BA, so we'd switch back to a
lower or zero power reduction
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
