summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath9k
AgeCommit message (Collapse)Author
2012-05-02Revert "ath9k_hw: Fix incorrect spur_freq_sd for AR9003"Rajkumar Manoharan
This reverts commit a844adfd7bee4edc66d337de6c33b348e83552a8. The commit a844adfd is degrading rx sensitivity of lower rate in HT40 mode and it is confirmed that reverting the change is improving rx sensitivity. spur_freq_sd (for self-corr in AGC) is defined with respect to the center of each 20MHz channel while spur_phase_delta (for self-corr in Rx and spur data filter) is defined with respect to the center of current RF channel. So in short, we need to subtract spur_freq_sd (for self-corr in AGC) by the offset between the center of primary20 and the center of RF channel in SW. This offset could be +/10 MHz for dynamic 40. Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com> Signed-off-by: Kai Shi <kaishi@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23ath9k: fix tx power settings for AR9287Gabor Juhos
The 'ath9k_hw_update_regulatory_maxpower' helper function has been introduced by commit a55f858852e4345d0a31af593c46738ca8614bff (ath9k_hw: Cleanup TX power calculation for AR9287). Updating of the max_power_level value has been moved into the helper function in that change, however the removed code from 'ath9k_hw_ar9287_set_txpower' has not been replaced with a call of the new helper function. Due to that missing call, retrieving tx power for 2x2 and 3x3 chainmask is not handled properly. During the calculation of the tx power for 2x2 and 3x3 chainmasks the values are reduced. Those reductions must be compensated during retrieving. Fix this by adding the missing call of the helper function. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23ath9k: add an extra boolean parameter to ath9k_hw_apply_txpowerGabor Juhos
In order to unifying regulatory limit handling commit ca2c68cc7bc80fc4504fb420df04cce99c9ee6ec (ath9k_hw: clean up tx power handling) introduced a new helper function 'ath9k_hw_apply_txpower', and the direct calls of 'ah->eep_ops->set_txpower' has been replaced by a call of the helper function. This caused a change in the behaviour of the 'ath9k_hw_set_txpowerlimit' function. The purpose of that function is to calculate and store the rate txpower table and the regulatory limit without touching the hardware registers. Before the commit, the 'test' parameter of the function was passed to the 'ah->eep_ops->set_txpower'. Now the calling of the 'set_txpower' function happens indirectly through 'ath9k_hw_apply_txpower', so the 'test' argument of the 'set_txpower' is always 'false'. This patch restores the original behaviour of 'ath9k_hw_set_txpowerlimit' by adding a new argument to 'ath9k_hw_apply_txpower.' Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17ath9k: Fix TX fragmentationSujith Manoharan
Assigning sequence number for frames without taking care of the fragment field breaks transmission of fragmented frames. Fix this by assigning the fragment number properly. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-13ath9k: wake up the hardware from full sleep when idle is turned offFelix Fietkau
The hardware needs a reset to recover from full sleep. Issue this reset directly in the ath9k_config call that turns off idle, otherwise tx remains dead until the first channel change after the idle state change Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-10Revert "ath9k: fix going to full-sleep on PS idle"Sujith Manoharan
This reverts commit c1afdaff90538ef085b756454f12b29575411214. Users have reported connection failures in 3.3.1 and suspend/resume failures in 3.4-rcX. Revert this commit for now - PS IDLE can be fixed in a clean manner later on. Cc: stable@vger.kernel.org Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-05Merge branch 'akpm' (Andrew's patch-bomb)Linus Torvalds
Merge batch of fixes from Andrew Morton: "The simple_open() cleanup was held back while I wanted for laggards to merge things. I still need to send a few checkpoint/restore patches. I've been wobbly about merging them because I'm wobbly about the overall prospects for success of the project. But after speaking with Pavel at the LSF conference, it sounds like they're further toward completion than I feared - apparently davem is at the "has stopped complaining" stage regarding the net changes. So I need to go back and re-review those patchs and their (lengthy) discussion." * emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches) memcg swap: use mem_cgroup_uncharge_swap fix backlight: add driver for DA9052/53 PMIC v1 C6X: use set_current_blocked() and block_sigmask() MAINTAINERS: add entry for sparse checker MAINTAINERS: fix REMOTEPROC F: typo alpha: use set_current_blocked() and block_sigmask() simple_open: automatically convert to simple_open() scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open() libfs: add simple_open() hugetlbfs: remove unregister_filesystem() when initializing module drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback fs/xattr.c:setxattr(): improve handling of allocation failures fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed fs/xattr.c: suppress page allocation failure warnings from sys_listxattr() sysrq: use SEND_SIG_FORCED instead of force_sig() proc: fix mount -t proc -o AAA
2012-04-05simple_open: automatically convert to simple_open()Stephen Boyd
Many users of debugfs copy the implementation of default_open() when they want to support a custom read/write function op. This leads to a proliferation of the default_open() implementation across the entire tree. Now that the common implementation has been consolidated into libfs we can replace all the users of this function with simple_open(). This replacement was done with the following semantic patch: <smpl> @ open @ identifier open_f != simple_open; identifier i, f; @@ -int open_f(struct inode *i, struct file *f) -{ ( -if (i->i_private) -f->private_data = i->i_private; | -f->private_data = i->i_private; ) -return 0; -} @ has_open depends on open @ identifier fops; identifier open.open_f; @@ struct file_operations fops = { ... -.open = open_f, +.open = simple_open, ... }; </smpl> [akpm@linux-foundation.org: checkpatch fixes] Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-03-28ath9k: Use HW HT capabilites properlySujith Manoharan
The commit "ath9k: Remove aggregation flags" changed how nodes were being initialized. Use the HW HT cap bits to initialize/de-initialize nodes, else we would be accessing an uninitialized entry during a suspend/resume cycle, resulting in a panic. Reported-by: Justin P. Mattock <justinmattock@gmail.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-26ath9k: fix a memory leak in ath_rx_tasklet()Eric Dumazet
commit 0d95521ea7 (ath9k: use split rx buffers to get rid of order-1 skb allocations) added in memory leak in error path. sc->rx.frag should be cleared after the pskb_expand_head() call, or else we jump to requeue_drop_frag and leak an skb. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Felix Fietkau <nbd@openwrt.org> Cc: John W. Linville <linville@tuxdriver.com> Cc: Trond Wuellner <trond@chromium.org> Cc: Grant Grundler <grundler@chromium.org> Cc: Paul Stewart <pstew@chromium.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-26ath9k: reduce listen time periodRajkumar Manoharan
When we have downlink traffic alone and the station is going thru bgscan, the client is out of operating channel for around 1000ms which is too long. The mac80211 decides when to switch back to oper channel based on tx queue, bad latency and listen time. As the station does not have tx traffic, the bgscan can easily affect downlink throughput. By reducing the listen time, it helps the associated AP to retain the downstream rate. Cc: Paul Stewart <pstew@google.com> Tested-by: Gary Morain <gmorain@google.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-26ath9k: fix max noise floor thresholdRajkumar Manoharan
Currently the maximum noise floor limit is set as too high (-60dB). The assumption of having a higher threshold limit is that it would help de-sensitize the receiver (reduce phy errors) from continuous interference. But when we have a bursty interference where there are collisions and then free air time and if the receiver is desensitized too much, it will miss the normal packets too. Lets make use of chips specific min, nom and max limits always. This patch helps to improve the connection stability in congested networks. Cc: stable@vger.kernel.org Cc: Paul Stewart <pstew@google.com> Tested-by: Gary Morain <gmorain@google.com> Signed-off-by: Madhan Jaganathan <madhanj@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-16Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem Conflicts: drivers/net/wireless/ath/ath9k/hw.c
2012-03-15ath9k_hw: remove unused initvalsFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: inline AR9271 1.0 INI overridesFelix Fietkau
Makes them more readable and reduces code size Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: remove iniModes_*_tx_gain_9271Felix Fietkau
Program tx gain through iniModesTxGain like on AR9287 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: clean up iniModesAdditionalFelix Fietkau
use iniModesFastClock for 5 ghz fast clock specific settings, and iniAdditional for clock/chip specific initval overrides Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: fix AR9380 register settings for channel 14Felix Fietkau
Program the ah->ini_japan2484 INI values which were left out by accident Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: fold ar9002_hw_cck_chan14_spread into mode regs initializationFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: remove iniCommon_*_cck_fir_coeff_9271Felix Fietkau
These arrays are unused Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: clean up ath9k_hw_setuprxdescFelix Fietkau
The ATH9K_HW_CAP_AUTOSLEEP check is bogus, the rx status area needs to be cleared on all non-EDMA PCI/AHB based chipsets anyway. Limit the memset to the rx status area to improve performance. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: remove ath9k_hw_gettxintrtxqsFelix Fietkau
The driver can just check the mask directly Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: optimize register access functionsFelix Fietkau
By checking for NR_CPUS, the compiler can optimize out register access serialization code on non-SMP kernels Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: remove ath9k_hw_getdefantennaFelix Fietkau
The default antenna (as programmed by the INI file) is always 0 anyway. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: remove ath9k_hw_htc_resetinitFelix Fietkau
Automatically set the ah->htc_reset_init on init and after PHY disable. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: clean up tx completion interrupt handlingFelix Fietkau
TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and used together, and they share the same bitmask in enum ath9k_tx_queue_flags. Simplify the code that tests for these flags. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: simplify tx queue interrupt mask handlingFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: Fix multi-VIF BSS handlingSujith Manoharan
mac80211 provides short preamble information and ERP protection information on a per-BSS basis, which can be used. Remove flags stored in the driver, which was incorrect since they were being used in a global manner. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: Remove aggregation flagsSujith Manoharan
SC_OP_TXAGGR and SC_OP_RXAGGR are not really needed. The HT capabilities of the station and HW can be used instead. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: Cleanup FastChannelChangeSujith Manoharan
The logic to determine whether to use FCC is a bit convoluted. Use a small helper function to decide whether FCC is to be used. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: Remove 'other' VIF countSujith Manoharan
It is not needed and will not be used anyway since unsupported interfaces are not allowed to be created. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: Remove unused variablesSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: Remove unnecessary initializationSujith Manoharan
There is no need to mask out SWBA/BMISS from the interrupt mask in start(). Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath9k: fix going to full-sleep on PS idleFelix Fietkau
The check for PS_WAIT_FOR_TX_ACK was inverted, the hardware should only go to full sleep if no tx is pending. Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath9k: Fix mactime from being clobbered in rx_statusAshok Nagarajan
mactime was being overwritten by the function ath9k_rx_skb_preprocess. Fixed by memsetting rx_status in ath_rx_tasklet. Signed-off-by: Ashok Nagarajan <ashok@cozybit.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath9k: configure bss info at assoc notificationRajkumar Manoharan
The proper place to configure bss info is at assoc notification. So that ath9k continues to work if the supirous bssid notification will be removed in future. Cc: Johannes Berg <johannes@sipsolutions.net> Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath9k_hw: Fix enabling of MCI and RTTMohammed Shafi Shajakhan
tested in AR9462 Rev:2, both hardware capability flag are set Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath9k: Fix BTCOEX shutdownSujith Manoharan
Flush MCI profiles only if MCI is being actually used. This fixes a panic on driver unload when non-MCI devices are being used and btcoex_enable is set. BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffffa06296d2>] ath_mci_flush_profile+0x12/0x100 [ath9k] Call Trace: [<ffffffffa061befe>] ath9k_stop_btcoex+0x5e/0x80 [ath9k] [<ffffffffa061ed57>] ath9k_stop+0xb7/0x230 [ath9k] [<ffffffffa0533f30>] ieee80211_stop_device+0x50/0x180 [mac80211] [<ffffffffa051f0cf>] ieee80211_do_stop+0x2af/0x6a0 [mac80211] [<ffffffffa051f4da>] ieee80211_stop+0x1a/0x20 [mac80211] [<ffffffff81365d96>] __dev_close_many+0x86/0xe0 [<ffffffff81365ee0>] dev_close_many+0xa0/0x110 [<ffffffff81366038>] rollback_registered_many+0xe8/0x260 [<ffffffff813661cb>] unregister_netdevice_many+0x1b/0x80 [<ffffffffa051e950>] ieee80211_remove_interfaces+0xd0/0x110 [mac80211] [<ffffffffa050c133>] ieee80211_unregister_hw+0x53/0x120 [mac80211] [<ffffffffa061d5a4>] ath9k_deinit_device+0x44/0x70 [ath9k] [<ffffffffa062c1d4>] ath_pci_remove+0x54/0xa0 [ath9k] [<ffffffff81267c46>] pci_device_remove+0x46/0x110 [<ffffffff8131021c>] __device_release_driver+0x7c/0xe0 [<ffffffff81310960>] driver_detach+0xd0/0xe0 [<ffffffff81310078>] bus_remove_driver+0x88/0xe0 [<ffffffff81311122>] driver_unregister+0x62/0xa0 [<ffffffff81268004>] pci_unregister_driver+0x44/0xc0 [<ffffffffa062c8b5>] ath_pci_exit+0x15/0x20 [ath9k] [<ffffffffa063205d>] ath9k_exit+0x15/0x31 [ath9k] [<ffffffff810b92cc>] sys_delete_module+0x18c/0x270 [<ffffffff814373dd>] ? retint_swapgs+0x13/0x1b [<ffffffff8124828e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff81437de9>] system_call_fastpath+0x16/0x1b Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-09Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
2012-03-07ath9k: fix signal strength reporting issuesFelix Fietkau
On A-MPDU frames, the hardware only reports valid signal strength data for the last subframe. The driver also mangled rx_stats->rs_rssi using the ATH_EP_RND macro in a way that may make sense for ANI, but definitely not for reporting to mac80211. This patch changes the code to calculate the signal strength from the rssi directly instead of taking the average value, and flag everything but the last subframe in an A-MPDU to tell mac80211 to ignore the signal strength entirely, fixing signal strength fluctuation issues reported by various users. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07ath9k: get rid of double queueing of rx frames on EDMAFelix Fietkau
Process rx status directly instead of separating the completion test from the actual rx status processing. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07ath9k: remove rssi/antenna information from recv debug statsFelix Fietkau
The way this is implemented (simply storing the last value) is absolutely worthless for debugging anything, and the same information is also available through the MAC sample feature, so there's no point in keeping this around. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07ath9k: make MAC sample statistics optionalFelix Fietkau
They're more expensive than some of the other debug options and only used in very rare situations, so it sometimes makes sense to disable them while leaving in debugfs support. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07ath9k_hw: use cold instead of warm reset on AR9280Felix Fietkau
Cold reset is more reliable for getting the hardware out of some specific stuck states. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05ath9k: make use of list_for_each_entry_safeMohammed Shafi Shajakhan
this does the same thing as the previous code Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05ath9k: completely zero intialize valid_phy_rate_idxMohammed Shafi Shajakhan
its better to zero initialize the 'valid_phy_rate_idx' array completely Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05ath9k: fix drv_tx_last_beacon on AR9003 by processing beacon tx statusFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05ath9k_hw: enable interrupts for beacon tx completion eventsFelix Fietkau
Not doing so could cause the tx status queue to overflow during longer periods of time without non-beacon tx. These events are also required for proper drv_tx_last_beacon handling. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05ath9k: do not call ath9k_hw_txprocdesc on AR9003 outside of the tx taskletFelix Fietkau
Since AR9003 uses a global tx status queue, processing tx status outside of the regular tx tasklet is dangerous and messes up hardware/software synchronization of tx status events. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05Revert "ath9k_hw: Fix false tx hung detection in AR9003 chips"Felix Fietkau
The approach of this change is flawed, as it triggers tx status processing from more callsites, yet the chips only have one global tx status queue. Subsequent patches will properly fix the issue that this one tried to address. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-16 07:20:18 +0000