1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
|
/*
* Copyright (C) 2008-2009 ST-Ericsson
*
* Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2, as
* published by the Free Software Foundation.
*
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl022.h>
#include <linux/spi/spi.h>
#include <asm/localtimer.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <plat/mtu.h>
#include <mach/hardware.h>
#include <mach/setup.h>
#define __MEM_4K_RESOURCE(x) \
.res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
/* These are active devices on this board */
static struct amba_device uart0_device = {
.dev = { .init_name = "uart0" },
__MEM_4K_RESOURCE(U8500_UART0_BASE),
.irq = {IRQ_UART0, NO_IRQ},
};
static struct amba_device uart1_device = {
.dev = { .init_name = "uart1" },
__MEM_4K_RESOURCE(U8500_UART1_BASE),
.irq = {IRQ_UART1, NO_IRQ},
};
static struct amba_device uart2_device = {
.dev = { .init_name = "uart2" },
__MEM_4K_RESOURCE(U8500_UART2_BASE),
.irq = {IRQ_UART2, NO_IRQ},
};
static void ab4500_spi_cs_control(u32 command)
{
/* set the FRM signal, which is CS - TODO */
}
struct pl022_config_chip ab4500_chip_info = {
.lbm = LOOPBACK_DISABLED,
.com_mode = INTERRUPT_TRANSFER,
.iface = SSP_INTERFACE_MOTOROLA_SPI,
/* we can act as master only */
.hierarchy = SSP_MASTER,
.slave_tx_disable = 0,
.endian_rx = SSP_RX_MSB,
.endian_tx = SSP_TX_MSB,
.data_size = SSP_DATA_BITS_24,
.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
.clk_phase = SSP_CLK_SECOND_EDGE,
.clk_pol = SSP_CLK_POL_IDLE_HIGH,
.cs_control = ab4500_spi_cs_control,
};
static struct spi_board_info u8500_spi_devices[] = {
{
.modalias = "ab4500",
.controller_data = &ab4500_chip_info,
.max_speed_hz = 12000000,
.bus_num = 0,
.chip_select = 0,
.mode = SPI_MODE_0,
.irq = IRQ_AB4500,
},
};
static struct pl022_ssp_controller ssp0_platform_data = {
.bus_id = 0,
/* pl022 not yet supports dma */
.enable_dma = 0,
/* on this platform, gpio 31,142,144,214 &
* 224 are connected as chip selects
*/
.num_chipselect = 5,
};
static struct amba_device pl022_device = {
.dev = {
.coherent_dma_mask = ~0,
.init_name = "pl022",
.platform_data = &ssp0_platform_data,
},
.res = {
.start = U8500_SSP0_BASE,
.end = U8500_SSP0_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
.irq = {IRQ_SSP0, NO_IRQ },
/* ST-Ericsson modified id */
.periphid = SSP_PER_ID,
};
static struct amba_device pl031_device = {
.dev = {
.init_name = "pl031",
},
.res = {
.start = U8500_RTC_BASE,
.end = U8500_RTC_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
.irq = {IRQ_RTC_RTT, NO_IRQ},
};
static struct amba_device *amba_devs[] __initdata = {
&uart0_device,
&uart1_device,
&uart2_device,
&pl022_device,
&pl031_device,
};
static void __init u8500_timer_init(void)
{
#ifdef CONFIG_LOCAL_TIMERS
/* Setup the local timer base */
twd_base = __io_address(U8500_TWD_BASE);
#endif
/* Setup the MTU base */
mtu_base = __io_address(U8500_MTU0_BASE);
nmdk_timer_init();
}
static struct sys_timer u8500_timer = {
.init = u8500_timer_init,
};
static void __init u8500_init_machine(void)
{
int i;
/* Register the active AMBA devices on this board */
for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
amba_device_register(amba_devs[i], &iomem_resource);
spi_register_board_info(u8500_spi_devices,
ARRAY_SIZE(u8500_spi_devices));
u8500_init_devices();
}
MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
/* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
.phys_io = U8500_UART2_BASE,
.io_pg_offst = (IO_ADDRESS(U8500_UART2_BASE) >> 18) & 0xfffc,
.boot_params = 0x100,
.map_io = u8500_map_io,
.init_irq = u8500_init_irq,
/* we re-use nomadik timer here */
.timer = &u8500_timer,
.init_machine = u8500_init_machine,
MACHINE_END
|
