| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
board/atmel/atngw100/atngw100.c
board/atmel/atstk1000/atstk1000.c
cpu/at32ap/at32ap700x/gpio.c
include/asm-avr32/arch-at32ap700x/clk.h
include/configs/atngw100.h
include/configs/atstk1002.h
include/configs/atstk1003.h
include/configs/atstk1004.h
include/configs/atstk1006.h
include/configs/favr-32-ezkit.h
include/configs/hammerhead.h
include/configs/mimc200.h
|
|
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Replace the avr32-specific board_init_info hook by the standard
board_early_init_r hook and make it optional.
board_early_init_r() runs somewhat earlier than board_init_info used to
do, but this isn't a problem for any of the in-tree boards.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
- Separate the portmux configuration functionality from the GPIO pin
control API.
- Separate the controller-specific code from the chip-specific code.
- Allow "ganged" port configuration (multiple pins at once).
- Add more flexibility to the "canned" peripheral select functions:
- Allow using more than 23 address bits, more chip selects, as
well as NAND- and CF-specific pins.
- Make the MACB SPEED pin optional, and choose between MII/RMII
using a parameter instead of an #ifdef.
- Make it possible to use other MMC slots than slot 0, and support
different MMC/SDCard data bus widths.
- Use more reasonable pull-up defaults; floating pins may consume a
lot of power.
- Get rid of some custom portmux code from the mimc200 board code. The
old gpio/portmux API couldn't really handle its requirements, but
the new one can.
- Add documentation.
The end result is slightly smaller code for all boards. Which isn't
really the point, but at least it isn't any larger.
This has been verified on ATSTK1002 and ATNGW100. I'd appreciate if
the board maintainers could help me test this on their boards. In
particular, the mimc200 port has lost a lot of code, so I'm hoping Mark
can help me out.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: Alex Raimondi <alex.raimondi@miromico.ch>
Cc: Julien May <julien.may@miromico.ch>
Changes since v1:
* Enable pullup on NWAIT
* Add missing include to portmux-pio.h
* Rename CONFIG_PIO2 -> CONFIG_PORTMUX_PIO to match docs
|
|
|
|
Renamed initialization functions for atngw100 and atstk1000.
Removed initializations for these boards from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
This cleans up the SDRAM initialization and related code a bit, and
allows faster booting.
* Add definitions for EBI and internal SRAM to asm/arch/memory-map.h
* Remove memory test from sdram_init() and make caller responsible
for verifying the SDRAM and determining its size.
* Remove base_address member from struct sdram_config (was sdram_info)
* Add data_bits member to struct sdram_config and kill CFG_SDRAM_16BIT
* Add support for a common STK1000 hack: 16MB SDRAM instead of 8.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Rework the HMATRIX configuration interface so that it becomes easier
to configure the HMATRIX for boards with special needs, and add new
parts.
The HMATRIX header file has been split into a general,
chip-independent part with register definitions, etc. and a
chip-specific part with SFR bitfield definitions and master/slave
identifiers.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
This is a replacement for ATSTK1002 with 64MB SDRAM and NAND flash on
board. It's currently in production and will be available soon.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
The existing code assumes the SDRAM row refresh period should always
be 15.6 us. This is not always true, and indeed on the ATNGW100, the
refresh rate should really be 7.81 us.
Add a refresh_period member to struct sdram_info and initialize it
properly for both ATSTK1000 and ATNGW100. Out-of-tree boards will
panic() until the refresh_period member is updated properly.
Big thanks to Gerhard Berghofer for pointing out this issue.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Set up the portmux for the MMC interface and enable the MMC driver
along with support for DOS partitions, ext2 and FAT filesystems.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Implement MACB initialization for AVR32 and ATSTK1000, and turn
everything on, including the MACB driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Conform to the "standard" interface and use initdram() instead of
board_init_memories() on AVR32. This enables us to get rid of the
sdram_size member of the global_data struct as well.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Rewrite the resource management code (i.e. I/O memory, clock gating,
gpio) so it doesn't depend on any global state. This is necessary
because this code is heavily used before relocation to RAM, so we
can't write to any global variables.
As an added bonus, this makes u-boot's memory footprint a bit smaller,
although some functionality has been left out; all clocks are enabled
all the time, and there's no checking for gpio line conflicts.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Patch by Haavard Skinnemoen, 12 Sep 2006
|
