diff options
Diffstat (limited to 'include/configs/yosemite.h')
| -rw-r--r-- | include/configs/yosemite.h | 137 |
1 files changed, 68 insertions, 69 deletions
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index cb2042ce6..b66ab58d8 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -55,36 +55,36 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ -#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 -#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 -#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 +#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CONFIG_SYS_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ +#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 /*Don't change either of these*/ -#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/ -#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs*/ +#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/ +#define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/ /*Don't change either of these*/ -#define CFG_USB_DEVICE 0x50000000 -#define CFG_NVRAM_BASE_ADDR 0x80000000 -#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000) -#define CFG_BOOT_BASE_ADDR 0xf0000000 +#define CONFIG_SYS_USB_DEVICE 0x50000000 +#define CONFIG_SYS_NVRAM_BASE_ADDR 0x80000000 +#define CONFIG_SYS_BCSR_BASE (CONFIG_SYS_NVRAM_BASE_ADDR | 0x2000) +#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ -#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ -#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ -#define CFG_INIT_RAM_END (4 << 10) -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */ +#define CONFIG_SYS_INIT_RAM_END (4 << 10) +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data*/ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ +#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ /*define this if you want console on UART1*/ #undef CONFIG_UART1_CONSOLE @@ -96,69 +96,68 @@ * Note: DENX encourages to use redundant environment in FLASH. */ #if 1 -#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #else -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ #endif /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CFG_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */ +#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#ifdef CFG_ENV_IS_IN_FLASH -#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) -#endif /* CFG_ENV_IS_IN_FLASH */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) +#endif /* CONFIG_ENV_IS_IN_FLASH */ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ -#define CFG_KBYTES_SDRAM (128 * 1024) /* 128MB */ -#define CFG_SDRAM_BANKS (2) +#define CONFIG_SYS_KBYTES_SDRAM (128 * 1024) /* 128MB */ +#define CONFIG_SYS_SDRAM_BANKS (2) /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR (0xa8>>1) -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#ifdef CFG_ENV_IS_IN_EEPROM -#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */ -#define CFG_ENV_OFFSET 0x0 -#endif /* CFG_ENV_IS_IN_EEPROM */ +#ifdef CONFIG_ENV_IS_IN_EEPROM +#define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */ +#define CONFIG_ENV_OFFSET 0x0 +#endif /* CONFIG_ENV_IS_IN_EEPROM */ /* I2C SYSMON (LM75, AD7414 is almost compatible) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_AD7414 1 /* use AD7414 */ #define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 70 -#define CFG_DTT_LOW_TEMP -30 -#define CFG_DTT_HYSTERESIS 3 +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 /* * Default environment variables @@ -186,13 +185,13 @@ /* USB */ #define CONFIG_USB_OHCI_NEW #define CONFIG_USB_STORAGE -#define CFG_OHCI_BE_CONTROLLER +#define CONFIG_SYS_OHCI_BE_CONTROLLER -#undef CFG_USB_OHCI_BOARD_INIT -#define CFG_USB_OHCI_CPU_INIT 1 -#define CFG_USB_OHCI_REGS_BASE (CFG_PERIPHERAL_BASE | 0x1000) -#define CFG_USB_OHCI_SLOT_NAME "ppc440" -#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 +#undef CONFIG_SYS_USB_OHCI_BOARD_INIT +#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 +#define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_PERIPHERAL_BASE | 0x1000) +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 /* Comment this out to enable USB 1.1 device */ #define USB_2_0_DEVICE @@ -226,29 +225,29 @@ #define CONFIG_PCI /* include pci support */ #undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ +#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/ /* Board-specific PCI */ -#define CFG_PCI_TARGET_INIT -#define CFG_PCI_MASTER_INIT +#define CONFIG_SYS_PCI_TARGET_INIT +#define CONFIG_SYS_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ -#define CFG_FLASH CFG_FLASH_BASE -#define CFG_CPLD 0x80000000 +#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CPLD 0x80000000 /* Memory Bank 0 (NOR-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x03017300 -#define CFG_EBC_PB0CR (CFG_FLASH | 0xda000) +#define CONFIG_SYS_EBC_PB0AP 0x03017300 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xda000) /* Memory Bank 2 (CPLD) initialization */ -#define CFG_EBC_PB2AP 0x04814500 -#define CFG_EBC_PB2CR (CFG_CPLD | 0x18000) +#define CONFIG_SYS_EBC_PB2AP 0x04814500 +#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_CPLD | 0x18000) -#define CFG_BCSR5_PCI66EN 0x80 +#define CONFIG_SYS_BCSR5_PCI66EN 0x80 #endif /* __CONFIG_H */ |