summaryrefslogtreecommitdiff
path: root/include/asm-arm
AgeCommit message (Collapse)Author
2011-05-31Silencing TOC and itp error messages not applicable to snowball.Mathieu J. Poirier
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2011-02-17Adding official machine ID.Mathieu J. Poirier
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2011-02-14Adding base support for snowball.Mathieu J. Poirier
- Initial pin configuration. - Introduction of u8500_is_snowball. - Introduction of new machine type. Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2011-01-31U8500: Kick the Cortex watchdog when dumpingPer Fransson
ST-Ericsson ID: 321908 Change-Id: Ib51c36558e37c7f52db638052644758e6d3cc51a Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/13848 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2011-01-27db8500: Verify signature of kernel before bootingRobert Rosengren
Verification of the kernel and ITP signature before allowing to boot is added. This feature is configurable and by default not activated. MeeGo- built RPM will have this enabled. ST-Ericsson ID: WP275634, ER275440 Change-Id: Ib888f39dd5dca1bc8b7d6e1b002da83a77908b07 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/11415 Tested-by: Robert ROSENGREN <robert.rosengren@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: QATOOLS Reviewed-by: Jens WIKLANDER <jens.wiklander@stericsson.com>
2011-01-18U8500: Add support for HREFP 2.0 V60 and laterMichael Brandt
The HREFP 2.0 V60 has no GPIO expander, therefore some GPIO lines were moved around. The preferred approach was to first check if there is a machid in the environment. And if not try to program the GPIOE. If that fails, assume it is a V60 or newer. But for the splash screen, we need to know very early on which HW version we are running. At that time no environment is available, therefore it is unavoidable to do the I2C access (10 ms timeout), if both HW versions shall be supported in one binary. CAUTION: you need also a Linux kernel which supports MACH_TYPE_HREFV60. Older U8500 kernels will not even issue a start-up message. Depends-On: http://gerrit.lud.stericsson.com/gerrit/12335 ST-Ericsson ID: CR 272893 Change-Id: Id794df8c185dfbf67f7bce81deb49abf71129f7b Signed-off-by: Michael Brandt <michael.brandt@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/12578 Reviewed-by: Torbjorn SVENSSON <torbjorn.x.svensson@stericsson.com> Reviewed-by: Robert ROSENGREN <robert.rosengren@stericsson.com> Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com> Reviewed-by: Bibek BASU <bibek.basu@stericsson.com>
2010-12-15db8500: Move ISSW code out from itp.cRobert Rosengren
Splitting security related code from itp.c into sec_bridge.c ST-Ericsson ID: WP275634 ST-Ericsson FOSS-OUT ID: Trivial Change-Id: I813daf0d0eaea4645e7d990bf467f19b0af968db Signed-off-by: Robert Rosengren <robert.rosengren@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/10895 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-15U8500: Move itp and cspsa into SoC directoryRobert Rosengren
itp.c and cspsa_fp.c is SoC specific, not board specific. Other db8500 based boards need it as well, therefore move it into the SoC directory. ST-Ericsson ID: WP275634 ST-Ericsson FOSS-OUT ID: Trivial Change-Id: I386c0d84e9f44f18ded0d9059fc2dae4c27974f2 Signed-off-by: Robert Rosengren <robert.rosengren@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/10894 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com> Reviewed-by: Joakim AXELSSON <joakim.axelsson@stericsson.com>
2010-12-08db8500: New GPIO driver and config, from Linux kernelJoakim Axelsson
Copied the GPIO configurator written for the Linux kernel. The Nomadik db8500 GPIO driver. Purpose is to be able to just cut-n-paste the GPIO config from Linux to U-boot. Also at the same time remove the obsolete and old gpio_alt_funcenable/disable methods. Now all is configured using a table in u8500.c. Now drivers doesn't have to worry about setting up the GPIO pins. Actually no driver today uses GPIO pins directly, only via hardware blocks within db8500. Functions are still added to be able to interact directly with a GPIO pin. This also cleaned up a lot of driver by not having to bit manipulate GPIO registers them self. The new driver is called db8500_gpio and placed in driver/gpio/. Functions are in include/db8500_gpio.h: void db8500_gpio_set_pull(unsigned gpio, enum db8500_gpio_pull pull); void db8500_gpio_make_input(unsigned gpio); int db8500_gpio_get_input(unsigned gpio); void db8500_gpio_make_output(unsigned gpio, int val); void db8500_gpio_set_output(unsigned gpio, int val); And for the configurator in include/db8500_pincfg.h: void db8500_gpio_config_pins(pin_cfg_t *cfgs, size_t num); All in all the final binary size has decreased. This is only done for db8500 nomadik GPIO. The code for gpio expanders has not been touched. All references to Nomadik has been removed in this driver. Only db8500 is left. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: I90aa1d46c813ffb5a777c3492b5751f5054f71cf Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9904 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: Clean up PRCMU code in db8500 SoC codeJoakim Axelsson
Clean up of PRCMU code in db8500 SoC code. Move things from cpu.c and clock.h to prcmu.c. Also remove duplicate #defines and have prcmu.c use the #defines in prcmu.h. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: Ieffb0094b3f43f0c88f3ed457c6cb296fa0ce378 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9899 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: Display cpu info.Joakim Axelsson
Enable CONFIG_DISPLAY_CPUINFO and implement print_cpuinfo() in cpu/arm_cortexa9/db8500.c. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: Id4f67b223fabc4a8007229f8db12bd2a7362f8c2 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7115 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: Move all clock code from board to SoCJoakim Axelsson
Moved clock code from board/st/u8500/u8500.c to cpu/arm_cortexa9/db8500/clock.c. Remove code to simulate Maja clocks. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: Ibbb21d53091ceaddcc01e1a195e129039f986696 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7114 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: Move cpu identifying function to SoC codeJoakim Axelsson
Moved u8500_is_earlydrop() and cpu_is_u8500*() to include/asm-arm/arch-db8500/cpu.h. They are kept in cpu.h as the functions are very small and should be inlined with each use of them. The final binary actually also became around 100 bytes smaller. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: Ied553b7c8a004a37c70c3e328a069ae8b2a92b23 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9893 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: Split arch_cpu code from boardJoakim Axelsson
First patch to split cpu_arch SoC-code away from board code. Added usage of arch_cpu_init() which is the corresponding to board_init(). Moved db8500 code from board/st/u8500/u8500.c to cpu/arm_cortexa9/db8500/cpu.c. Also created include/asm/arch-db8500/cpu.h and include/asm/arch-db8500/prcmu.h. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: I403d7d4f6c655c0d383afb3cb3be7e7df96683a3 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7150 Reviewed-by: Joakim AXELSSON <joakim.axelsson@stericsson.com> Tested-by: Joakim AXELSSON <joakim.axelsson@stericsson.com> Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-07db8500: cpu-arch rename stw8500 to db8500Joakim Axelsson
Started work with splitting the files in board/st/u8500 into proper SoC (system on a chip), drivers, commands and board code. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: I33300b1990f377bc049785102f1c87fbe579e86d Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7089 Reviewed-by: Robert ROSENGREN <robert.rosengren@stericsson.com> Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Mikael LARSSON1 <mikael.xt.larsson@stericsson.com>
2010-11-19U8500: Removed duplicates of common.h and gpio.hMichael Brandt
common.h and gpio.h were present in the u8500 board directory and in the SoC include directory include/asm-arch/arch-stw8500. This patch removes the duplicates in the board directory and replaces all "common.h" and "gpio.h" with <asm/arch/common.h> and <asm/arch/gpio.h>, respectively. Change-Id: I4ff2a3a11324200222e3ae5b9d22eee6427f6d4c Signed-off-by: Michael Brandt <michael.brandt@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/8838 Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com> Reviewed-by: Rikard OLSSON <rikard.p.olsson@stericsson.com>
2010-11-17arm: update mach-typesMian Yousaf Kaukab
To get numbers for 5500 machines and official SVP8500 numbers. ST-Ericsson ID: ER280045 mach-types are equivalent to the following patch: ST-Ericsson ID: AP279856 Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Change-Id: I0ce5ce2c31cc3e35fadd01acc20f077992be2f0d Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/8775 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-11-12U8500: Load splash image from TOCMikael Larsson
This patch removes splash image from u-boot binary and loads it from a toc entry called SPLASH instead. Depends-On: I2e182df7fa056a5df2deb05a4ebab844eedbb85d I715045aba01c1c747f9bd15f02c6d057f66ff968 I93e63a092fd6f229f530e55ec4b98e8e09db1c06 ST-Ericsson ID: ER268766 Change-Id: I4ee7885618d18d526dfca55d7c45b769cd9b52c9 Signed-off-by: Mikael Larsson <mikael.xt.larsson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/6879 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Rikard OLSSON <rikard.p.olsson@stericsson.com>
2010-11-04U8500: Add support for SPIMarkus Helgesson
Added SPI support for U8500 ST-Ericsson ID: 269867 ST-Ericsson FOSS-OUT ID: STETL-FOSS-OUT-10121 Change-Id: Ied17dd39aa1ebc0ee95818c59c7f211ce655b8bf Signed-off-by: Markus Helgesson <markus.helgesson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7569 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-08-31prcm: fix DB8500v2 TCDM base address and I2C chip idRabin Vincent
Handle the changed TCDM base address on DB8500v2, and the required chip bits to the I2C slave address. Based on the Linux modifications. Change-Id: I9fc8df1553824bd03a908a5c4285be284ea158db Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/4213 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-08-20ux500: add DB8500v2 supportRabin Vincent
- Add cpu_is_u8500v2() for identification: ASICID has moved, so use the MIDR for primary identification. - Handle the changed MTU0 enable bit - Handle the MMC DBLOCKSIZE field move ST-Ericsson ID: CR267426 Change-Id: Ieae6032cf4e96796a8b53cfb95b28b26d4cf9a7b Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/3960 Reviewed-by: Martin LUNDHOLM <martin.xa.lundholm@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-08-11Replace MMC/SD driver to fit new framework.Ulf Hansson
IR265772: MMC driver does not detect SDHC cards. IR254201: Restructure MMC/SD driver for U8500 board according to the block device framework in mainline U-Boot. Changes to mmc framework: - Multi Block Read support in mmc framework. - Wrap Multi Block Write/Read to be able to adopt for large transaction. - Removed incorrect check in EXT CSD for high capacity MMC. - Corrected check for high capacity SD cards. - Set MMC buswidth to 8, prio of using 4. Known limitations/bugs in mmc framework: - High capacity MMC, will likely not get the correct density. - High speed is set, whether or not the host supports it or not. board/st/u8500/mmc_utils: IMPORTANT FOR DEVELOPERS: - Removed unessary U-Boot commands which is already supported in cmd_fat. - mmc_read_cmd_file: Read command.txt into bootcmd env from FAT FS in SD card. - write_partition_block: Writes the MBR if it is not already written. board/st/u8500/mmc_host[c.h]: - Implements the entire MMC/SD host driver for the PL180 block. - There is still room for optimization: Increase CLK-speed. Use high-speed for SD cards. Is GPIO setup correctly for both cards an eMMC. EarlyDrop support not fully tested. Dynamically turn on voltage/clocks to SD, not always. More... Note: - Increased read/write performance for eMMC, to around 5.4 MB/s for sequential read/write. Earlier measurements was 3.5 MB/s for read and 2.6 MB/s for write. ST-Ericsson ID: ER265772, CR267996, ER267993 Change-Id: I921102edbde761407ff5ad476d1bb99f5dc7a2ef Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/2288 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Martin LUNDHOLM <martin.xa.lundholm@stericsson.com> Tested-by: Martin LUNDHOLM <martin.xa.lundholm@stericsson.com> Reviewed-by: Mikael LARSSON <mikael.xt.larsson@stericsson.com> Tested-by: Mikael LARSSON <mikael.xt.larsson@stericsson.com>
2010-07-23Boottime changes. Moved generic boottime code from lib_arm to common. ↵Jonas Aaberg
Boottime now internally uses us instead of ticks. Reviewed-by: Michael Brandt <michael.brandt@stericsson.com> Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Change-Id: If30d2eb384d6e82daa86c3cab7a6fd2a22baefb5 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/3053 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-07-19Applies vibrator support for U-boot.Grzegorz Sygieda
This implements vibrator feature using AB8500 chip and I2C i/f. The vibrator driver provides shell command "vibrate". Checked with HREFP boards: 1.1_V21, 1.1_V31, 1.1_V33 ST-Ericsson ID: AP266348 Change-Id: Ifd0d780b41c4285038b8de659cdeac2086b8e873 Signed-off-by: Grzegorz Sygieda <grzegorz.sygieda@tieto.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/2937 Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-06-10Adding support for startup graphicsJimmy Rubin
This patch does the following: * Startup graphics only support for HREF+. * Displays a logo last in the u-boot sequence before the kernel is booted. * Informs the kernel not to display penguins. * Added pmem values to bootargs. ST Ericsson Change-ID: WP236570 Change-Id: Ib176c17a795ddd002e94344eb9c67739b1e2269e Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/1048 Reviewed-by: Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
2010-05-24Use proper copyright linesRabin Vincent
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Change-Id: Ieec8e7940e7acdc88d7c17b12007f61841741325 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/390 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
2010-05-24HREF+ SD supportRabin Vincent
On HREF+, SD card power supply is controlled by the Vaux3 regulator. In order to enable the power supply, port the AB8500 PRCMU I2C read/write code from Linux to U-Boot, and then write the appropriate registers via those functions. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Change-Id: I470f3da694e6ea0e3e0e16571c3048066f0a4309 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/388 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
2010-05-19HREF V1 updatesMichael Brandt
This patch is part of WP254081 which depends on WP252006. * Fixed I2C, use real timeouts instead of counter * Undefined CONFIG_BOOTTIME, since it as to be changed to new timer.c * Merged V1 patches from Bangalore The patches were merged manually, because of the differences of the U-Boot baseline (Bangalore U-Boot 1.3.1, Lund 2009.11). The original patches were created by Rabin Vincent <rabin.vincent@stericsson.com>. and were applied originally to Branches: blr_lsp, remotes/origin/blr_lsp Follows: qpppaaa_20100210_094651 0001-u8500-gpio-add-I2C0-altfun.patch 0002-u8500-use-correct-v1-macros.patch 0003-emmc-clean-up-paritioning.patch 0004-u8500-remove-incorrect-ram-settings.patch 0005-u8500-gpio-remove-unnecessary-ifdefs.patch 0006-u8500-add-ED-v1-detection-and-handle-eMMC-diff.patch 0008-u8500-mmc-don-t-disable-altfuns.patch 0009-u8500-gpio-remove-unused-defined.patch 0010-u8500-mmc-add-barrier-for-while-loop.patch 0011-u8500-mmc-handle-non-block-addressed-cards.patch 0012-u8500-mmc-remove-unused-gpio-settings-on-v1.patch 0013-u8500-emmc-build-fix.patch 0014-u8500-handle-v1-gpios-and-clocks.patch 0015-mmc-build-fix-for-block-addressing.patch 0016-u8500-add-clocks-and-hardware-files.patch 0017-u8500-enable-PRCUM-timers-reg-for-ED.patch 0018-u8500-handle-MTU-for-v1-ED.patch 0019-u8500-emmc-remove-unnecessary-GPIO-settings.patch 0020-u8500-remove-dead-code.patch 0021-u8500-add-working-MTU-timer.patch 0022-pl011-empty-rx-fifo-if-necessary.patch 0023-u8500-gpio-fix-cont-handling-in-altfunc.patch 0024-u8500-reduce-bootdelay-to-1-and-enable-zero-check.patch 0025-u8500-disable-forcing-of-verify-but-set-n-by-default.patch 0029-u8500-fix-some-gpio-settings.patch 0030-emmc-make-v1-paritioning-differences-explicit.patch Signed-off-by: Michael Brandt <Michael.Brandt@stericsson.com> Change-Id: I1106702e393c34f630e71f071e06c3952b0d3a1a Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/182 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Jonas ABERG <jonas.aberg@stericsson.com> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
2010-01-13Merge branch 'master' of http://git.denx.de/u-bootMichael Brandt
2010-01-13Updated timing measurement structure, changed atags and added idle time ↵Jonas
measurement. Note: idle time measurement does not seem to work reliable at the moment. Verification needed. Signed-off-by: Michael Brandt <Michael.Brandt@stericsson.com>
2010-01-12Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2010-01-09DA8xx: Add GPIO register definitionsAjay Kumar Gupta
Added DA8xx GPIO base addresses in gpio_defs.h and pointers to different BANKs which can be used to program GPIOs. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Swaminathan S <swami.iyer@ti.com>
2010-01-06ARM Update mach-typesTom Rix
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php And built with repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm commit c9f937e4a3f4ebf9924ec21d80632e5eb61d949c Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2010-01-04Davinci: NAND enable ECC even when not in NAND boot modeNick Thompson
Davinci: NAND enable ECC even when not in NAND boot mode On Davinci platforms, the default NAND device is enabled (for ECC) in low level boot code when NAND boot mode is used. If booting in another mode, NAND ECC is not enabled. The driver should make sure ECC is enabled regardless of boot mode if NAND is configured in U-Boot. Signed-off-by: Nick Thompson <nick.thompson@ge.com>
2010-01-04Davinci: Configurable NAND chip selectsNick Thompson
Davinci: Configurable NAND chip selects Add a CONFIG_SYS_NAND_CS setting to all davinci configs and use it to setup the NAND controller in the davinci_nand mtd driver. Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
2010-01-04Merge branch 'boottime' into mop500Michael Brandt
Conflicts: .gitignore include/configs/u8500.h
2009-12-22Merge branch 'master' of http://git.denx.de/u-bootMichael Brandt
Conflicts: include/usb/musb_udc.h
2009-11-30Corrected timer errors and changed MTU0 timer from 0 to 3 due to 0 is used ↵Jonas
by the linux kernel and we still want to be able to use that timer for boottime measurement. IE leave the 3rd timer run until we're executing init. Added atags for u-boot timing measurements as communication with the kernel.
2009-11-29ARM Update mach-typesTom Rix
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php And built with repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm commit 3fcca9ac6cbce35b3e81e247d375534117d5f4cd Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-11-27arm: A320: Add support for Faraday A320 evaluation boardPo-Yu Chuang
This patch adds support for A320 evaluation board from Faraday. This board uses FA526 processor by default and has 512kB and 32MB NOR flash, 64M RAM. FA526 is an ARMv4 processor and uses the ARM920T source in this patch. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2009-11-27OMAP3: Fix SDRC initNishanth Menon
Defaults are for Infineon DDR timings. Since none of the supported boards currently do XIP boot, these seem to be faulty. fix the values as per the calculations(ACTIMA,B), conf the sdrc power with pwdnen and wakeupproc bits Signed-off-by: Nishanth Menon <nm@ti.com>
2009-11-27OMAP3:SDRC: introduce DDR typesNishanth Menon
Micron DDR timings based on: http://www.sakoman.net/cgi-bin/gitweb.cgi?p=x-load-omap3.git;a=blob;f=include/asm/arch-omap3/mem.h;h=e6fbfe3947f5d0d85fea776e30821d4017316d86;hb=HEAD Introduce Micron DDR timings and provide CONFIG_OMAP3_INFINEON_DDR and CONFIG_OMAP3_MICRON_DDR config options to allow for platform files to setup their timings as per the type of DDR selected Reported-by: Steve Sakoman in http://www.nabble.com/forum/Permalink.jtp?root=25779518&post=25959734&page=y Signed-off-by: Nishanth Menon <nm@ti.com>
2009-11-27OMAP3:SDRC: Cleanup references to SDPNishanth Menon
Remove SDP referenced unused defines Signed-off-by: Nishanth Menon <nm@ti.com>
2009-11-27Add TI DA8xx support: DA8xx includesNick Thompson
Provides initial support for TI OMAP-L1x/DA8xx SoC devices. See http://www.ti.com The DA8xx devices are similar to DaVinci devices but have a differing memory map and updated peripheral versions. Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2009-11-27Add a unified s3c24x0 header filekevin.morfitt@fearnside-systems.co.uk
This patch adds a unified s3c24x0 cpu header file that selects the header file for the specific s3c24x0 cpu from the SOC and CPU configs defined in board config file. This removes the current chain of s3c24-type #ifdef's from the s3c24x0 code. Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27Clean-up of s3c24x0 header fileskevin.morfitt@fearnside-systems.co.uk
Cleans up the s3c24x0 header files: s4c24x0.h: removes the use of 'volatile' from the S3C24X0_REG8, S3C24X0_REG16 and S3C24X0_REG32 register typedef's. Registers are always accessed using the IO accessor functions which cast the register address as 'volatile' anyway so it isn't required here. s3c2400.h and s3c2410.h: insert a blank line between the static inline functions Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
2009-11-27s3c64xx: move s3c64xx header files to asm-arm/arch-s3c64xxMinkyu Kang
This patch moves the s3c64xx header files from include/ to include/asm-arm/arch-s3c64xx Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27Move s3c24x0 header files to asm-arm/arch-s3c24x0/kevin.morfitt@fearnside-systems.co.uk
This patch moves the s3c24x0 header files from include/ to include/asm-arm/arch-s3c24x0/. checkpatch.pl showed 2 errors and 3 warnings. The 2 errors were both due to a non-UTF8 character in David M?ller's name: ERROR: Invalid UTF-8, patch and commit message should be encoded in UTF-8 #489: FILE: include/asm-arm/arch-s3c24x0/s3c2410.h:3: + * David M?ller ELSOFT AG Switzerland. d.mueller@elsoft.ch As David's name correctly contains a non-UTF8 character I haven't fixed these errors. The 3 warnings were all because of the use of 'volatile' in s3c24x0.h: WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt #673: FILE: include/asm-arm/arch-s3c24x0/s3c24x0.h:35: +typedef volatile u8 S3C24X0_REG8; +typedef volatile u16 S3C24X0_REG16; +typedef volatile u32 S3C24X0_REG32; I'll fix these errors in another patch. Tested by running MAKEALL for ARM8 targets and ensuring there were no new errors or warnings. Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27ARM Update mach-typesTom Rix
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php And built with repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm commit 156171c71a0dc4bce12b4408bb1591f8fe32dc1a Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-11-27ARM Update mach-types.hTom Rix
From http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm Commit id 0996391139f43d032335b5360db11da62a2cbb39 Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-05-15 00:41:37 +0000